Search Documents

By Robert B. Fulton, Gill Montgomery

Fluorspar is the commercial name for fluorite, a mineral that is calcium fluoride, CaF2. The name, derived from the Latin word fluere (to flow), refers to its low melting point and its early use in metallurgy as a flux. It is the principal industrial source of the element fluorine. Cryolite, sodium aluminum fluoride, Na3AlF6, is a rare mineral which has been found in commercial quantities only in Greenland. The natural material has been supplanted by synthetic cryolite for its principal industrial use in the manufacture of aluminum. History Fluorspar was used by the early Greeks and Romans for ornamental purposes as vases, drinking cups, and table tops. Various peoples, including the Chinese and the American Indians, carved ornaments and figurines from large crystals. Its usefulness as a flux was known to Agricola in sixteenth century Europe. Fluorspar mining began in England about 1775 and at various places in the United States between 1820 and 1840. Production grew substantially following the development of basic open-hearth steelmaking, wherein it is used as a flux. Use was stimulated by growth of the steel, aluminum, chemical, and ceramic industries, particularly during World Wars I and II. Fluorocarbons entered the picture in 1931. The use of anhydrous hydrogen fluoride (HF) as a catalyst in the manufacture of alkylate for high octane fuel began in 1942. Differential flotation for separating fluorspar from galena, sphalerite, and common gangue minerals in the 1930s, and the application of heavy-media concentrating methods to the treatment of low-grade ores in the 1940s were outstanding technological advances that facilitated increased production. Recently, pelletizing and briquetting of flotation concentrates for use in steel furnaces and the development of flotation schemes for beneficiating ores containing abundant dolomite and barite have been major improvements in the industry. Uses of Fluorspar Fluorspar is used to make hydrogen fluoride, also called hydrofluoric acid, an intermediate for fluorocarbons, aluminum fluoride, and synthetic cryolite. It is used as a flux in the steel and ceramic industries, in iron foundry and ferroalloy practice, and has many minor specialized uses. Hydrogen fluoride (HF) is produced by reacting acid grade (97% CaF2) fluorspar with sulfuric acid in a heated kiln or retort to produce HF gas and calcium sulfate. After purification by scrubbing, condensing, and distillation, the HF is marketed as anhydrous HF, a colorless fuming liquid, or it may be absorbed in water to form the aqueous acid, usually 70% HF. Synthetic cryolite, organic and inorganic fluoride chemicals, and elemental fluorine are made from hydrofluoric acid. The acid itself is important in catalysis in the manufacture of alkylate, which is an ingredient in high-octane fuel for aircraft and automobiles, in steel pickling, enamel stripping, glass etching and polishing, and in various electroplating operations. The manufacture of one ton of virgin aluminum requires about 50 to 60 lb of fluorine content in synthetic cryolite and alumnium fluoride. This quantity, through improved technology and recovery practices, is being lowered significantly.

Jan 1, 1983

On August 4, 1844, J. C. Fremont made the first record found of coal in Wyoming. On the North Fork of the Platte River, beyond Medicine Butte, in Carbon County, he noted: "in the precipitous bluffs were displayed a succession of strata containing fossil, vegetable remains, and several beds of coal. In some of the beds, the coal did not appear to be perfectly mineralized; and in some of the seams, it was compact and remarkably lustrous." A little later he noted, "longitude 111°, latitude 4 1/2°-Muddy R.--coal."1 In 1848, Clayton reported coal on Sulphur Creek near the site of old Bear River City, in Uinta County.2 Maj. Osborne Cross in his journal, on July 1, 1849, records seeing coal on Deer Creek and in one of the hills near Crooked Muddy Creek, in Converse County; on July 7, he records that the country from Deer Creek to the Sweetwater River abounds in coal, probably in Natrona and Carbon Counties.3 A letter from Asst. Quartermaster Van Vliet to General Jessup dated July 25, 1850, asked an appropriation for building shops at Fort Laramie for making repairs for the emigrants, and mentions "coal and timber," but undoubtedly meant charcoal, as no other mention of stone coal is made in the records of the fort.4 Stansbury, in 1852, placed on his map of this section the words: "Great Coal Basin," extending from the west bank of Bear River, near the present Evanston, to Point of Rocks in Sweetwater County. In 1859, a military coal reservation was established near here, but the coal was never worked to any great extent, although probably some was hauled to Fort Bridger for smithing purposes. When the fort was abandoned this reservation returned to the public lands .2 In the same year (1859), Hayden traced the lignite formation uninterruptedly from the upper Missouri Valley to a point on the North Platte River, about 80 miles northwest of Fort Laramie.5 On August 25, 1865,

Jan 1, 1942

The work of the Committee during the year 1914 was especially directed to the securing of a larger representation in the Institute of those engaged in coal mining and coking. While these industries exceed in volume and in monetary importance all other mining industries in the United States, the membership of the Institute representing them has in recent years been relatively small. It was thought that an increase in the membership of the Institute obtained from among those engaged in these industries was desirable in order to increase interest in the work of the Institute, for this result can only be reached by securing the presentation and publication of a larger number of papers relating to these industries. It is evident that the reading of such papers will tend to increase the attendance at the local and general meetings of the Institute. Sessions of the Coal and Coke Committee were held and a number of papers relating to these subjects were presented at the meetings at Butte, Salt Lake, and Pittsburgh, the Pittsburgh meeting especially being planned with this in view. The activities of the Local Section of the Institute organized in the Pennsylvania Anthracite region have reawakened interest in that district and it is hoped that the same object can be obtained in the bituminous coal fields, either through the organization of one or more. local sections, affiliation with some of the local coal-mining societies, or through activities of the Coal and Coke Committee. Referring to the work of the Committee in its efforts to increase the membership of the Institute, the Committee desires to acknowledge the services rendered by many members scattered throughout the various coal-mining districts of the United States, in compiling lists of those qualified for membership in the Institute, but who have not yet become members. The lists so compiled comprised about 1,100 names, which were furnished to the Committee by the co-operation of 40 or 50 members of the Institute.

Jan 3, 1915

By A. S. Nowick, A. E. Roswell

Anelastic measurements of atomic mobility in an Ag-Zn substitutional solid solution, make possible a study of the rate of decay of lattice defects frozen into the alloy by quenching. A WIDE variety of experimental evidence has accumulated recently in support of the belief that atomic mobility or diffusion in face-centered cubic lattices occurs principally through the movement of lattice defects, as contrasted to a mechanism by which two or more atoms directly exchange lattice positions. The most direct evidence, summarized in a recent review,' includes the Kirkendall-effect measurements and anelastic measurements on quenched alloys. Theoretical calculations' have focused attention on the lattice vacancy as the defect probably responsible for diffusion in the common metals. Later calculations3 have also shown the possible importance of combined pairs of vacancies in producing diffusion. The only defect that has been considered seriously, in addition to the vacancy and combination of vacancies, is the "interstitialcy" (an atom which has left its normal lattice position and entered an interstitial position) ; the calculated energy of formation of an interstitialcy in a close-packed lattice is too large to permit a reasonable probability for the occurrence of this defect In view of these calculations it may be tentatively concluded that the defects producing atomic movements are single or multiple vacancies. Anelastic measurements of atomic mobility in substitutional solid solutions provide a valuable method for the study of lattice defects. By means of this method it was first demonstrated' that defects may be frozen into a lattice by rapid quenching from high temperatures. (It was subsequently shown6 that resistivity measurements may also be capable of detecting the presence of frozen-in defects.) A summary of the principles involved in these anelastic measurements will now be presented. The anelastic method is based on a relaxation phenomenon in substitutional solid solutions, first discovered by Zenera in a brass and subseauentlv investigated extensively in a series of Ag-zn solid solutions.' This relaxation effect may be observed in the usual way either dynamically, as a peak in

Jan 1, 1954

By H. J. Oberson, J. H. Brown

Comminution devices such as rod or ball mills are characteristically nonselective in their operation in that all material fed to a mill is ground to some extent. This is unfortunate when the object of comminution is liberation, for not only is energy expended in breaking pure gangue particles wasted, but, since gangue is frequently the predominant phase, the opportunity for such loss is great. Ideally, in this application a comminuting device should develop fracture only in locked particles. In the present investigation an attempt was made to use the large density difference which may exist between minerals to prevent comminution of one while grinding the other. EXPERIMENTAL MATERIALS AND EQUIPMENT The two minerals used in this work were -8-mesh galena and -8+ 20-mesh quartz. All tests were made on 2000-g charges containing 50 pct by weight of each mineral. Heavy media suspensions consisted of -100-mesh ferrosilicon in water. For grinding, a laboratory mill 10 in. diam by 12 in. long was filled to about 30 pct of its volume with either a ball or a rod charge. The balls ranged in size from 3/8 to 1 1/8 in. in diam; the rods ranged from 5/8 to 1 1/4 in. diam by 11 in. long. EXPERIMENTAL PROCEDURE In all tests employing heavy media, the ground pulps were treated as follows: 1) After recovering the ground charge from the mill but before drying, the pulp was wet screened on 200 mesh. 2) After drying the + 200-mesh product from step 1, the ferrosilicon was removed magnetically. 3) The nonmagnetic quartz and galena product from step 2 was sized on 10-mesh through 200-mesh screens. 4) The mineralogical composition of each screen fraction was determined by measuring its specific gravity. The specific gravity was related to the weight of galena in the fraction through the relationship

Jan 1, 1961

By Herbert H. Kellogg, Nathaniel Arbiter, Arthur F. Taggart

THE experimental work herein described is presented in support of the following broad hypothesis: Conditioning of metals and metallic sulphides by amine collectors involves metathetic reaction at the solid surface between the collector and an oxidized metallic compound, to produce a coating comprising an amine-bearing compound of low solubility in the system. The type of reaction is different in acid and in basic solutions; both types may occur simultaneously in near-neutral pulps. EXPERIMENTAL The experiments comprise contact-angle tests with a variety of metals and metallic sulphides and extraction tests on ground chalcocite. Contact-angle tests were made principally on metals. Covellite paralleled metallic copper in amine solution at pH 8.8 (Table 3) and in alkaline water, but maintained an angle of about 70° in 10-3 HCl solution, where metallic copper lost its angle. The tests with anionic collectors (Table I) indicate that the behavior of metals in general is parallel to that of their minerals in anionic solutions. It is believed that this is generally true with cationic collectors also, but the covellite test is a warning against a broad assumption to this effect. All test specimens were mounted in Transoptic.* All tests in conditioning solution were preceded by a test in distilled water; cleaning and polishing were continued in every case until the angle in water was zero. Subsequent transfers into and out of solutions and test cells were made in such a way as to prevent exposure of the surface to air.1 The amine used was primary laurylamine, Armour and Co., AM-1120. It was used in the form of the hydrochloride, obtained by precipitation with gaseous hydrochloric acid from an ether solution of the amine, and purified by two recrystallizations from ether-alcohol.2 Inorganic and other test reagents were standard laboratory grades. [ ] Temperatures were not controlled; the probable range of test-solution temperatures is 65° t0 80°F.

Jan 1, 1943

By Arthur F. Taggart, Herbert H. Kellogg, Nathaniel Arbiter

The experimental work herein described is presented in support of the following broad hypothesis: Conditioning of metals and metallic sulphides by amine collectors involves metathetic reaction at the solid surface between the collector and an oxidized metallic compound, to produce a coating comprising an amine-bearing compound of low solubility in the system. The type of reaction is different in acid and in basic solutions; both types may occur simultaneously in near-neutral pulps. Experimental The experiments comprise contact-angle tests with a variety of metals and metallic sulphides and extraction teats on ground chalcocite. Contact-angle tests were made principally on metals. Covellite paralleled metallic copper in amine solution at pH 8.8 (Table 3) and in alkaline water, but maintained an angle of about 70° in Io-3 HCl solution, where metallic copper lost its angle. The tests with anionic collectors (Table I) indicate that the behavior of metals in general is parallel to that of their minerals in anionic solutions. It is believed that this is generally true with cationic collectors also, but the covellite test is a warning against a broad assumption to this effect. All test specimens were mounted in Transoptic.* All tests in conditioning solution were preceded by a test in distilled water; cleaning and polishing were continued in every case until the angle in water was zero. Subsequent transfers into and out of solutions and test cells were made in such a way as to prevent exposure of the surface to air.1 The amine used was primary laurylamine, Armour and Co., AM-1120. It was used in the form of the hydrochloride, obtained by precipitation with gaseous hydrochloric acid from an ether solution of the amine, and purified by two recrystallizations from ether-alcoho1.2 Inorganic and other test reagents were standard laboratory grades. Temperatures were not controlled; the probable range of test-solution temperatures is 650 to 80°F.

Jan 1, 1943

By Herbert H. Kellogg, Nathaniel Arbiter, Arthur F. Taggart

The experimental work herein described is presented in support of the following broad hypothesis: Conditioning of metals and metallic sulphides by amine collectors involves metathetic reaction at the solid surface between the collector and an oxidized metallic compound, to produce a coating comprising an amine-bearing compound of low solubility in the system. The type of reaction is different in acid and in basic solutions; both types may occur simultaneously in near-neutral pulps. Experimental The experiments comprise contact-angle tests with a variety of metals and metallic sulphides and extraction teats on ground chalcocite. Contact-angle tests were made principally on metals. Covellite paralleled metallic copper in amine solution at pH 8.8 (Table 3) and in alkaline water, but maintained an angle of about 70° in Io-3 HCl solution, where metallic copper lost its angle. The tests with anionic collectors (Table I) indicate that the behavior of metals in general is parallel to that of their minerals in anionic solutions. It is believed that this is generally true with cationic collectors also, but the covellite test is a warning against a broad assumption to this effect. All test specimens were mounted in Transoptic.* All tests in conditioning solution were preceded by a test in distilled water; cleaning and polishing were continued in every case until the angle in water was zero. Subsequent transfers into and out of solutions and test cells were made in such a way as to prevent exposure of the surface to air.1 The amine used was primary laurylamine, Armour and Co., AM-1120. It was used in the form of the hydrochloride, obtained by precipitation with gaseous hydrochloric acid from an ether solution of the amine, and purified by two recrystallizations from ether-alcoho1.2 Inorganic and other test reagents were standard laboratory grades. Temperatures were not controlled; the probable range of test-solution temperatures is 650 to 80°F.

Jan 1, 1943

By E. A. Anderson

In another paper' the writer has shown that the low permissible maximum fiber stress in a loaded zinc sheet demands a much closer support spacing than is used for steel. The limiting fiber stress in 13-gage (0.032 in.) sheets having a 1-in. depth of corrugation was found to be about 5000 lb. per sq. in. on a 37-in. span under a load of 40 Ib. per sq. ft. Corrugated steel sheets are commonly laid with spans varying from 48 to 60 in. In order to increase the span in 13-gage zinc to 54 in. (a common spacing) the metal must be capable of withstanding, under long-continued loading, a maximum fiber stress of about 10,000 lb. per sq. in. This is known to be impossible with unalloyed zinc. In this paper the writer describes a series of experiments leading up to the development of an alloy capable of safely sustaining this fiber stress. The effect of alloying on the slow creep of zinc was studied by means of static tensile tests, accurate determinations of apparent elastic limits and finally by means of loading tests on full-size roof sections. Two industrial buildings roofed with alloyed zinc sheets on spans involving fiber stresses in excess of 10,000 lb. per sq. in. have been under observation for over two years without signs of sagging. Experimental Work Two methods of increasing the maximum permissible fiber stress in zinc were considered. Cold rolling, which' increases the stiffness and tensile strength, was found to decrease the resistance to slow flow. Alloying, therefore, provided the only feasible means of obtaining the desired result, It was recognized that the improvement secured by the solid solution of natural impurities was insufficient. A series of alloys was outlined, therefore, in which a number of metals were added separately and together. The sheets rolled from these alloys were tested under

Jan 1, 1930

By Howard N. Eavenbon

The low-volatile, or smokeless, coal field of southern West Virginia is in Fayette, Raleigh, Wyoming, Mercer, Summers and McDowell counties, in the extreme southern portion of the state, and extends into the adjacent counties of Tazewell and Buchanan in Virginia. McDowell County is the largest producer, with Fayette and Raleigh counties next. The total area of the field (Fig. 1) is approximately 1600 square miles, or 1,024,000 acres. The percentage of volatile matter in the various seams ranges from 15 to 26 per cent, The upper limit of true low-volatile coal is usually considered to be 23 per cent volatile matter; above this point, the coal usually is classed as medium volatile. This limit will be used in this paper. Geological Position of Seams The smokeless seams are among the oldest coal seams in the country, as the Pocahontas group of rocks is the lowest member of the coal-bearing series and rests on top of the Mauch Chunk red shale, in or below which no coal seams of any importance occur. The Pocahontas group, or Lower Pottsville measures, has a thickness of 750 ft. in southern McDowell County, which decreases to about 350 ft. at Prince, on the New River, in Fayette County, 50 miles to the northeast. In this group, at various points, 12 coal beds have been found, of which 4 have been found in workable thickness and are now being mined. The New River group, or Middle Pottsville measures, is just above the Pocahontas group and varies in thickness from 1300 ft. in southern McDowell County to about 700 ft. along New River. At various places, 16 beds of smokeless coal have been identified in this group, of which 5 have been found in workable thickness and are now being mined. A general columnar section of these strata is shown on Fig. 2. The workable seams in these strata, arranged in geological sequence, are as shown on page 77.

Jan 1, 1932

By John Mark Patek

Knowledge of the relative floatability of silicate minerals is increasing in importance as flotation is being applied to the concentration of nonsulfides. Many silicates are in themselves commercial products amenable to concentration by flotation. Moreover, the selective flotation of other nonsulfide minerals, such as cassiterite, depends largely upon the floatability of associated gangue silicates. Differences in floatability existing between the various silicates have not- been sufficiently appreciated; for example, the feldspars that differ greatly in floatability have generally been merely treated as "feldspar." It was the purpose of the work described in this paper to determine by experiment the differences in floatability between silicates; to investigate the causes for such differences, and to discover a means of predetermining approximate floatability without the necessity of experimentation. Determining Floatability The relative floatability of 20 silicates so selected as to represent all of the more common silicate types1 was obtained by flotation tests enumerated in Table 1. The mineral to be floated was crushed dry on a steel plate, and screened repeatedly during crushing through an 80-mesh screen in order to produce a sand with all grains as close to 80 mesh as possible. The sand was placed in dilute (6N) hydrochloric acid until free of soluble foreign material, and then washed with tap water about ten times in order to remove both acid and fines. The resultant product, which averaged 82 per cent plus 200 mesh, was floated in 50-gram charges in a 50-gram Denver celluloid flotation machine with 0.008 gram of terpineol, and from 0.01 to 0.05 gram of oleic acid in a solution acidified with sulfuric acid. The degree of separation of one mineral from another was determined by counting under a nlicroscope the grains of each mineral, both in the concentrate and in the tailings, and comparing their relative abundance in each. Unless the comparison showed a decided difference in amount,

Jan 1, 1935

By G. Willard Quick

FAILURES in railroad rails have been of vital concern to engineers; railroad executives, rail manufacturers and the general public for years. Failures from transverse fissures originating from internal nuclei have received particular attention in the past 20 years. Dr. J. E. Howard first reported this type of failure in 1911, as being responsible for a wreck-on the Lehigh Valley R. R. in which several lives were lost. Since then many transverse fissures have been found. In 1919, Waring and Hofammann1 etched longitudinal sections of rails in hot acid and found cracks extending both longitudinally and transversely in certain used rails as well as in some new rails.. Since then it has been thought by many that these "shatter" cracks are the nuclei from which transverse fissures subsequently develop in service. Methods for reducing the rate of cooling rails on the hot. bed have been devised to decrease the temperature gradient and consequently the stress gradient in the rails. A study of the tensile properties of rails at elevated temperatures was made by Freeman and Quick,2 who investigated the properties at temperatures through which rails pass on the cooling bed after leaving the hot saw. In their investigation a special study was made of the ductility of the steels in the temperature range 400° to 700° C. In this temperature range it was found that certain rail and other steels showed a marked decrease in elongation and reduction of area. The phenomenon was called "secondary brittleness" and the temperature range the "secondary brittle range." A tentative explanation was presented that internal failure such as "shatter cracks" and "hair cracks" in rails are the result of thermal stresses developed in the steel structure while cooling through the secondary brittle range. The investigation showed that the magnitude of the phenomenon varies for different heats, but that it did not differ for specimens from different ingots or for different rails in a particular ingot. It was also shown that annealing rail steel at a temperature either above or below the critical

Jan 1, 1932

By M. J. Greaves, Alan English

Pelletizing on a commercial scale is only 10 years old; yet in this period more than 150 million tons of pellets have been produced. Instrumentation and controls have played an important part in the development of an entirely new industry in almost unprecedented time. Initially, most control circuits used in the pelletizing industry were manually operated, since the confidence factor in instruments and controls was quite low at that time. This changed considerably in recent years and improvements in the use of instruments and controls have probably developed more rapidly in pelletizing than in any other metallurgical process. Now, within a decade of the start of commercial operations, the use of manually operated controls has changed and consideration is being given to the utilization of computers for data logging and control purposes.

Jan 7, 1965

Charles T. Malcolmson, Chicago, Ill.:—Mr. Blauvelt's admirable paper is a valuable contribution to the literature on briquetting of coal in this country. It should have a special significance for those interested in the commercial development of the coal-briquette industry. I believe that the data included in Mr. Blauvelt's paper will be particularly useful because they represent costs taken from a briquette-plant in actual operation. There are several points touched on in Mr. Blauvelt's paper which may bear comment in the way of emphasis rather than of criticism. In the first place, he has stated a fact which becomes axiomatic to any one who has had any experience in the design, building, or operation of coal-briquette plants, and that is, that the press is only one factor in the successful opera-

Jan 1, 1911

By W. M. Baldwin, J. T. Brown

The effect of hydrogen on the ductility, c, of SAE 1020 steel at strain rates, i, from 0.05 in. per in. per rnin to 19,000 in. per in. per rnin and at temperature, T, from +150° to —320°F was determined. The ductility surface of the embrittled steel reveals two domains: one in which and the other in which The usual "explanations" of hydrogen embrittlement are in accord with the first of these domains only. THE purpose of this investigation was a fuller A characterization of this of the investigation effects of varying temperature and strain rate on the fracture strain of hydrogen-charged steel. To be sure, it is known that low and high temperatures remove the embrittlement that hydrogen confers upon steels at room temperature,1 * see Fig. la and b, and that high strain rates have a similar effect,'-' see Fig. 2a, b, and c. However, the general effect of these two testing conditions on the fracture ductility of hydrogen-charged steels is not known, i.e., the three-dimensional graphical representation of fracture ductility as a function of temperature and strain rate is not known—only two traverses of the graph are available. The need for such a graph is not pedantic. To demonstrate this point, Fig. 3a, b, and c shows three of many three-dimensional graphs, all possible on the basis of the two traverses at hand. The important point (as will be developed in the Discussion) is that each of them would indicate a different basic mechanism for hydrogen embrittlement. It will be noted that the four types of ductility surfaces in Fig. 3a, b, and c may be characterized as follows: Material and Procedure Tensile tests were made at various temperatures and strain rates on a commercial grade of % in. round SAE 1020 steel in both a virgin state and as charged with hydrogen. The steel was spheroidized at 1250°F for 168 hr to give the unembrittled steel the lowest possible transition temperature. The steel was charged cathodically with hydrogen as follows: The specimen was attached to a 6 in. steel wire, degreased for 5 min in trichlorethylene, rinsed with water, and fixed in a plastic top in the center of a cylindrical platinum mesh anode. The assembly was placed in a 1000 milliliter beaker containing an electrolyte of 900 milliliters of 4 pct sulphuric acid and 10 milliliters of poison (2 grams of yellow phosphorous dissolved in 40 milliliters of carbon disulphide). A current density of 1 amp per sq in. was used which developed a 4 v drop across the two electrodes. All electrolysis was carried on at room temperature. Temperatures for tensile tests were obtained by immersing the specimens in baths of water (+70° to + 150°F), mixtures of liquid nitrogen and isopen-tane (+70° to —24O°F), and boiling nitrogen (-240" to-320°F). Specimens were tested in tension at strain rates of 0.05, 10, 100, 5000, and 19,000 in. per in. per min. The 0.05 and 10 in. per in. per rnin strain rates were obtained on a 10,000 lb Riehle tensile testing machine, the 100 in. per in. per rnin rate on a hydraulic-type draw bench with a special fixture, and the 500 and 19,000 in. per in. per rnin rates on a drop hammer. The fracture ductility of hydrogen-charged steel at room temperature and normal testing strain rates (-0.05 in. per in. per min) is a function of electro-lyzing time, dropping to a value that remains constant after a critical time.'* Under the conditions of • The hydrogen content of the steel continues to increase with charging time even after the ductility has leveled off to its saturated value.' this research the saturated loss in ductility occurred at approximately 30 min, see Fig. 4, and a 60 min charging time was taken as standard for all subsequent tests. After charging the steel with hydrogen, the surface was covered with blisters. These have been described by Seabrook, Grant, and Carney.' The original diameter of the specimen was not reduced by acid attack, even after 91 hr. Results The ductility of both uncharged and charged specimens is given as a function of strain rate in Fig. 5, and as a function of temperature at four different strain rates in Fig. 6. These results are assembled into a three-dimensional graph in Fig. 7. It is seen that the locus of the minima in the ductility curves of the charged steels divides the ductility surface into two domains. At temperatures below the minima,

Jan 1, 1955

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit.' The rocks are well-consolidated Gila conglomerate, quartz monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Ranaome. In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 3Y4x41/4-in. tool joints; 8-in. bits, 23/4x 3 3/4-in. tool joints; 6-in. bits, 21/4x31/4-in. tool joints; 4-in. bits, 15/ix25/s-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property. To allow for 2-in. drill pipe with tool joints, 31/2-in. core barrels and bits were used. With the standard 31h-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 5 to 37/8 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven machines. The open churn drill hole was cased with 21h-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in un-consolidated material like the formations drilled by

Jan 1, 1953

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit.' The rocks are well-consolidated Gila conglomerate, quartz monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Rannome. In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 31/4x41/4-in. tool joints; 8-in. bits, 23/4x 33/4-in. tool joints; 6-in. bits, 2Y4x3Y4-in. tool joints; 4-in. bits, 15/ix25/8-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property. To allow for 23/8-in. drill pipe with tool joints, 31h-in. core barrels and bits were used. With the standard 31h-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 55/8 to 3 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven machines. The open churn drill hole was cased with 21h-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in un-consolidated material like the formations drilled by

Jan 1, 1953

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit.' The rocks are well-consolidated Gila conglomerate, quartz monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Ranaome. In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 3Y4x41/4-in. tool joints; 8-in. bits, 23/4x 3 3/4-in. tool joints; 6-in. bits, 21/4x31/4-in. tool joints; 4-in. bits, 15/ix25/s-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property. To allow for 2-in. drill pipe with tool joints, 31/2-in. core barrels and bits were used. With the standard 31h-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 5 to 37/8 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven machines. The open churn drill hole was cased with 21h-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in un-consolidated material like the formations drilled by

Jan 1, 1953

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit.' The rocks are well-consolidated Gila conglomerate, quartz monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Rannome. In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 31/4x41/4-in. tool joints; 8-in. bits, 23/4x 33/4-in. tool joints; 6-in. bits, 2Y4x3Y4-in. tool joints; 4-in. bits, 15/ix25/8-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property. To allow for 23/8-in. drill pipe with tool joints, 31h-in. core barrels and bits were used. With the standard 31h-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 55/8 to 3 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven machines. The open churn drill hole was cased with 21h-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in un-consolidated material like the formations drilled by

Jan 1, 1953

Mr. Joseph P. GAZZAM,Germiston, Transvaal, So. Africa (communication to the Secretary*) :—About fourteen years ago, in southeastern Missouri,I used a method for the wet determination of lead which closely resembles the modified sulphate-chromate method described by Mr.. Guess. The principal difference, however, is, that after dissolving the lead chromate in hydrochloric acid, the chromic acid is determined by means of a standard solution of ferrous sulphate. The method, which I believe is still in use in southeastern Missouri, was found to be convenient and accurate for the determination of lead in the ores and various products of the mills and furnaces in that district, but it was never used for complex ores. A number of determinations of lead in mill-tailings were made in the year 1891; a few of these results are given in Table I. Table I.—Determinations of Lead in MilL-Tailings by Wet Assay.

Jan 1, 1905