Search Documents

By J. T. Ryan

SAFETY practice or the elimination of accidents in our coal mines is specifically a problem of management. It cannot be delegated to any governmental agency except that the various coal-producing states do and should have some minimum safety standard laws. However, the legislative method of attempting to control mine accidents is ineffective because of the delay between the necessity and the action. It will always be impossible to keep our various state mining laws up to date; and when the law says you must do a certain thin there is a tendency to do this and no more. Unless the scheme for setting up state regulations is so flexible that when a new hazard develops it can be immediately and adequately covered and the whole responsibility for accident elimination placed undivided on the

Jan 1, 1937

By Arthur L. Bishop

INTRODUCTION Purpose The in-situ leach method for uranium extraction is a relatively new and innovative method of uranium mining. In 1975, the first commercial in-situ facility began operation in south Texas. Since that time numerous other operations have been initiated as either pilot or commercial ventures. Considerable literature has been published that deals primarily with generalities of the process or environmental concerns. Several federal agencies have published documents which do not reflect the true operating or environmental nature of the in-situ leach method of uranium extraction. From an environmental standpoint, this is also evident in the promulgation of rules and regulations. Hence, the purpose of this paper is to present experience with an environmental concern--non- production zone excursions--such that the industry and the regulatory agencies will gain greater insight devoid of preconceived ideas and misconceptions. General Process Description In south Texas, in-situ leach mining is utilized to extract uranium from permeable sandstone ore deposits 61 to 213 meters (200 to 700 feet) below the surface. Uranium is present as an insoluble uranium oxide. In the in-situ or solution mining technique, anoxidizing lixiviant is injected into the formation through injection wells. The solution reacts with the insol uble carbonate complex. This soluble uranium complex is produced at recovery wells, each containing a submersible pump. During production there is a constant sweeping of lixiviant through the formation from the injection wells to the recovery wells. Injection and recovery wells can be arranged in any of a number of geometric patterns dependent upon ore body configuration, aquifer permeability, and operator preference. Submersible pumps in the recovery wells pump the uranium rich pregnant solution to the initial processing facility. Monitor wells surrcsund the pattern area and are screened in appropriate stratigraphic horizons (production and non-production zones) to detect any lixiviant migration that may occur (Fig. 1).

Jan 1, 1980

By George C. Branner

STATE geological surveys have had an interesting development in this country. They first appeared more than a hundred years ago. The fact that they have persisted and are now an important part of most state governments indicates the basic need for state departments con-cerned with mineral problems. The number of state surveys in 1941 (43) is at an all-time high, as is the aggre¬gate appropriation for their support for the fiscal year 1940-'41 ($1,600,708). The first surveys, those of North and South Carolina (see Fig. 1), made their appearance in 1820-'30, but neither survived that period. During the next two decades surveys were created in twenty states, but only three survived. In fact, it was not until the decade 1900-'10, when eighteen surveys were created and only five abolished, that these agencies became firmly established.

Jan 1, 1941

By F. W. Davis

SOME idea may be gained of the tremendous consumption of refractories by the open-hearth steel manufacturers from a statement made by A. T. Green at a meeting reported by T11.e Industrial Chemist of London, as follows: "At a very progressive steel plant in the Midlands, with a battery of five open-hearth furnaces working. twelve months and making 3000 tons of steel per week, the cost of refractories per ton of steel produced averages about $0.50 for the actual open- hearth casting and $0.12 for those operations incidental to the rolling of the metal." .These figures, when translated into the annual tonnage of steel, represent a very considerable expenditure.

Jan 1, 1930

By Archer E., Wheeler

Producing copper companies were active during 1941 owing to the national defense program the United States and the requirements of the friendly belligerent nation. This activity extended to the American owned properties in South America, the major part of whose product was taken by the Metals Reserve Co., a U.S. Government agency. Anaconda Copper Mining Co. is building a new converter plant at Anaconda, with four units of the Peirce-Smith type. The addition is being built adjacent to the reverberatory plant so as to avoid the necessity of hauling matte and slag. It is expected to be completed this year.

Jan 1, 1942

By Lyle D. Randen

With the environmental movement beginning in the late 1960's came a deluge of permit requirements for the mining industry. Coal mining has been one of, if not the most, severely impacted of the mineral industries as a result of the passage of the Federal Surface Mining Control and Reclamation Act of 1977. Numerous provisions of this Act and numerous regulations developed under authority of the Act are being challenged in differing levels of the judicial system across the United States. Such court cases have had varied success. Numerous other regulatory programs that are not quite as dramatic as the SMCRA have presented an unending regulatory problem for mining operators. My comments in this presentation relate primarily to the major Federal and State agencies and their legal responsibilities which we in the coal mining industry must address in order to receive authority to construct and operate surface coal mines in the State of Wyoming. A list of the Federal and State agencies one could deal with in an application is as follows: 1. Bureau of Land Management (BLM). BLM is responsible for deciding where and when to lease federally owned coal and for establishing terms and conditions for leases. BLM also has some control over surface reclamation on federal land, i.e. regrading to eliminate highwalls, covering of spoils, maximum extraction of coal to limit future disturbance, contemporaneous reclamation, etc. BLM is also responsible for designation of federal lands unsuitable for all or certain types of surface coal mining operations. 2. Geological Survey (USGS). USGS coal mining responsibilities apply only to Federal and Indian lands and concern compliance with production requirements including diligent development, minimum production levels, royalty payments and resource protection, and

Jan 1, 1983

By M. L. Requa

This paper is abstracted from the report of the Appraisement Committee of the Independent Oil Producers' Agency, of which the writer was Chairman. The other members of the committee were M. V. McQuigg and R. S. Haseltine. To Thomas Cox, engineer in charge of the investigation, and to his efficient staff of assistants, is due the credit for the detail work necessary in carrying out the plan of the Committee. It treats only of the valuation of the lands, wells, and piping, without going into details of equipment and other features. It was recognized, early in the operation, that the value of oil lands was the value of oil to be extracted, and marketed, less the costs attendant thereon. Referring this back to the costs in cents per barrel, it became obvious that surface improvements, absolutely necessary in the production of oil, from wells then drilled; had no separate and independent value aside from the value of the land, but that any excess equipment, not necessary for the production of oil from present wells, such as drilling tools, well casing, etc., should be given a present condition value. In valuing the properties of the Independent Oil Producers' Agency, the Committee has considered the following facts: 1. That from each property there will ultimately be. produced a certain total quantity of oil. 2. That in the production of that oil a certain total quantity of money will be expended. 3. That a certain total amount of money will be received from the oil. 4. That the total net receipts will be the total gross receipts less the cost of development and production. 5. That the present value of the net receipts must be such an amount that when invested by a purchaser it will be returned with 8 per cent. interest additional during the life of the property.

Jan 2, 1918

By William P. Blake

Copper Basin in Yavapai county, Arizona Territory, about twenty miles southwest of Prescott, is well named. It is a depressed area, and a region of cupriferous impregnation.* The geologic conditions are simple. The foundation rock is a coarse-grained granite and gneiss, in which soda feldspar predominates. There are also dykes of porphyritic rock, and a large quartz vein containing pyrites. Superimposed on this crystalline foundation, we find heavy beds of mechanically formed rocks, conglomerates, breccias, and sandstones, in horizontal layers cropping along the bed of a creek, and apparently the remnants of a much more extended formation, now denuded and largely carried away by gradual atmospheric erosion. The heavy beds of conglomerate are in many places much broken and tilted up, even standing on edge in large blocks, as if they had been lifted by some great convulsion; but the cause is much more simple, being merely the removal by gradual disintegration and erosion of the softened and decayed granitic rock below. The materials of these sedimentary beds are chiefly fragments of granite, gneiss, and plutonic rocks loosely mingled. They are the chief repositories of the copper-ore, which forms the cementing substance. This copper-ore is the blue and the green carbonate, azurite and malachite, and the ore is so generally spread through the mass of the beds that the blue and the green croppings can be seen at a great distance, particularly after or during a shower of rain, when the colors are extremely brilliant and beautiful. The copper carbonate is not only a matrix and a cementing material for the fragments of rock, but it invests and covers these fragments so that only malachite and azurite are visible. The beds are from three to ten feet or more in thickness, and, although seemingly solid carbonate of copper, rarely contain over 12 or 15 per cent. of that metal. Some portions of the conglomerates are much more highly charged with copper than others, and in places the beds are almost without copper. If a lump of the coarse sandstone

Jan 1, 1889

By AIME AIME

THE Federated American Engineering Societies through its Executive Board has endorsed House Bill 5230, introduced April 26, 1921, which provides for- the completion of the topographical survey of the United States. Before this bill can be reported out it will be necessary for the House Committee on -interstate and foreign commerce to hold hearings. This will not be done unless the engineers of the country show interest -and demand action which should be taken immediately after the recess ends and Congress reconvenes this fall. Surveys and maps have been made in this country ever since Captain John Smith mapped Chesapeake Bay about. 300 years ago, but it is only in comparatively recent years that the need for accurate maps has been keenly felt by those engaged in the industrial' and commercial development of the country.

Jan 1, 1921

By E. C. Lee

THE safety of mine workers has received more attention from both State and Federal law-making bodies than any other industry, a fact that shows clearly the hazardous nature of the industry. The last, but by no means the least, of the measures adopted for the protection of mine workers, is workmen's compensation legislation. This is proving to be a powerful instrument for greater safety in the industries, from the fact that special stress is laid not on how the accident happened or who may have been responsible for it, but on how badly the employee is hurt by it. The injured person does not have to employ lawyers to prove his case, because the mere fact of his employment is proof of his right to compensation. The immediate effect of such legislation is the certainty confronting the mine operator that he must pay out large sums for every accident, regardless of its cause, thus adding materially to the cost of the production of his coal. This fact furnished to the operator the strongest incentive to reduce the causes of accidents; not that the operator has ever lacked reasonable consideration for the welfare of his employees and a proper humane interest in their safety, but his engrossment in earning his daily livelihood has been so great that he has not felt that he had the time to devote to the safety of the operation. This time he must now find because of the actual-cash value of the prevention of accidents in his mines. This agency alone proved inadequate to bring about a material improvement because operators have always been willing enough to improve safety conditions when possible to do so within reasonable limits of their financial ability. The requirement in the Workmen's Compensation Laws of several of the States, that the mine operator shall insure as a guarantee of his ability to meet his compensation obligations, has furnished the needed incentive, moral and financial, necessary to the prompt and effective dissemination of a more general knowledge of the causes and

Jan 10, 1917

By G. F. Jenkins

ASBESTOS is a general term embracing the fibrous varieties of a number of minerals. Of these, the hydrous magnesium silicate, chrysotile (H4Mg3Si209), a variety of serpentine, is the most abundant and useful to industry. All other types of asbestos belong to the amphibole group of minerals and are classified as: crocidolite, NaFe(SiO3), FeSiO3; anthophyllite, (MgFe)SiO3; amosite, also a ferromagnesium silicate but with iron content higher than that of anthophyllite; tremolite, CaMg3(SiO3)4; and, actinolite, Ca (MgFe)3(SiO3)4. PROPERTIES The commercial value of asbestos depends largely on the physical property that permits it to be readily separated into fine filaments of high tensile strength and flexibility, which, coupled with the fact that it has the quality of incombustibility of a mineral-in distinction to vegetable and animal fibers-makes it of unique usefulness for many purposes. To some extent, the value depends upon the length of the fiber, although extreme length is neither necessary nor desirable for most purposes. Chrysotile occurs as cross-fiber veins, in which the asbestos fibers are approximately' at right angles to the vein walls, with vein width- or fiber length-seldom exceeding 2 or 3 in.; also as slip-fiber, in which the fibers 'lie in the same plane as the vein or on slippage planes. A cleanly broken vein of cross-fiber has a pearly luster and may range from a deep green or brown color to light shades of yellowish green or cream. When of good quality, the fiber filaments forming the vein may be easily drawn away from their neighbors and exhibit a fine silkiness and pure white color. They may be twisted into a thread and when flexed between thumb and fingers are found to be strong and pliable. Chrysotile withstands comparatively high temperatures without breaking down completely or fusing but begins to lose water of crystalliza-

Jan 1, 1949

By Fred Porter

Pollution problems from smelters may be unique in industry since the pollutants cover the wide range of SOx, particulates, carcinogens (arsenic), plus a number of heavy metals, the health implications of which are not clearly understood. In addition to this wide range of pollutants, many of the plants are extremely old; and fugitive emissions may, in fact, be the most significant air pollution problem. The Environmental Protection Agency, both in an in-house and contract effort, has assessed the quantity of pollutants emitted and evaluated the health impact. This paper will review the status of EPA's regulatory efforts in both new and existing smelters in light of these pollutant assessment studies.

Jan 1, 1976

By AIME AIME

FEW indeed are the sections of the country where trained or partly trained workers have not already been hired by a war industry plant or will be within the near future. Yet right in the midst of the heavily industrialized East lies the anthracite area, home of a million people, whose productive power has persistently been by-passed either by private industry or by the Government Plant Site Board. The chief reason given for not locating war plants in the area is that it is not within the strategic zone, but in numerous instances elsewhere this rule has been waived. Furthermore, the anthracite region is well protected on all sides by mountains and is at all points more than 100 miles inland. Continued depression in the anthracite industry and a crippling blow dealt by the war emergency to the production of silk and rayon goods, the chief manufacturing activity of the area, have resulted in a heavy migration, particularly of trained young workers, into near-by industrial areas. At least 50,000 people are currently unemployed, with the likelihood of an increase in coming months, and as many families are on relief.

Jan 1, 1942

CONTENTS PAGE FOGLER, M. F., and QUINN, E. J.-Scratch and Brinell Hardness of Severely Cold-rolled Metals. Discussed by H. S. Rawdon, Carl Benedicks, M. F. Fogler, A. L.Davis 1 GREEN, C. H. Eutectic Patterns in Metallic Alloys. Discussed by Carl Benedicks, Carle R. Hayward, G. E. Dalbey, George F. Comstock, C. H. Green. 3 ARCHER, ROBERT S., and JEFFRIES, ZAY.-New Developments in High-strength Aluminum Alloys. - Discussed by F. B. Coyle, M. F. Fogler, Zay. Jeffries, D. J. McAdam, Jr., Horace C. Knerr, Ernest Schweizer 6 FLICK, FULTON B.-Etching Aluminum and Its Alloys for Macroscopic and Microscopic Examination. Discussed by Samuel Daniels 22. MERICA, PAUL D., and WALTENBERG, R. G.-The Malleability of Nickel. Discussed by H. W. Gillett, Ancel St. John. L. W. McKeehan, A. L. Feild, A. L. Davis 23 ANDERSON, ROBERT J., and NORTON, JOHN T.-X-ray Evidence Versus the Amorphous-metal Hypothesis. Discussed by Zay Jeffries, Chu Phay Yap, Francis B. Foley, H. H. Lester, Edgar C. Bain, Ancel St. John, L. W. McKeehan, Carle R. Hayward, R. P: Heuer, Jerome Alexander, Carl Benedicks 26 COOK, MAURICE, and EVANS, ULICK R.-Recrystallization and Grain Growth in Soft Metals. Discussed by M. F. Fogler 36 POLUSHKIN, E. P.-Determination of Structural Composition of Alloys by a . Metallographic Planimeter. Discussed by H. S. Rawdon 36 BASSETT, WILLIAM H., and DAVIS, C. H.-Corrosion of Copper Alloys in Sea Water. Discussed by W. B. Price, W.. R. Webster, George A. Orrok, A. E. White, William H. Bassett, D. K. Crampton 38, Scratch and Brinell Hardness of Severely Cold-rolled Metals Discussion of the paper of M. F. FOGLER and E. J. QUINN, presented at the New York Meeting, February, 1925, and issued as Paper No. 1395-E with MINING AND METALLURGY, January, 1925. H. S. RAWDON, * Washington, D. C.-We had the privilege of looking over the data just given before they were published and we were not able to suggest any convincing reason for the differences that were secured

Jan 6, 1925

By Milton H. Fies

EARLY in 1945 the laboratories of the Southern Research Institute will begin active research investigations on behalf of industrial clients. This achievement has come after four years of planning by a group of Alabama businessmen, and is in partialanswer to an urgent need in the South. Those who conceived the Institute have long realized that a marked relationship exists between scientific research and the economic well-being of the several regions of the country. Clearly, technological research, generally absent in the South, is the medium through which are created new finished goods industries, and the increase of technological research is perhaps the most important long-range project in the South.

Jan 1, 1945

By HARRY H. SMITH

IT IS my understanding that, speaking broadly, the function of the engineering profession is to find how to do the thing required better for less money. Mechanical engineers, mining engineers, and the various other kinds of engineers are engaged in discovering and effectuating new and improved methods .of producing better goods and services at less cost to industry. The savings and advantages, thus, accruing ace reflected from time' to time in increased productive powers of industry and lower costs to the public which consumes the goods and services.

Jan 1, 1931

By Austin E. Dwight

IT has been shown by Oelsen and Wever' that the effect of a solute element on the allotropic transformation in iron is dependent upon the quantity

Jan 1, 1957

By A. G. Rozner

TRANSVERSE rupture tests have been commonly used in mechanical investigations of brittle materials. The specimens are simple, easy to prepare, and loading presents no difficulty. Owing to the complexity of stress distribution in bending1 one can determine stresses rigorously only for the elastic range. The bend-test results, however, are at times converted into tensile-strength data, determined as maximum fiber stress. The assumption is made that for small plastic deformations the linear stress-strain relation applies. This problem was experimentally investigated by Bach3 who tested cast iron in bending and in tension and found that the maximum fiber strength obtained in bending exceeded the experimental tensile strength by a factor depending on the geometry of the tested piece. The factor varied from 1.57 for a rectangular cross section to 2.12 for a circular cross section of the tested beam. Since this work was carried out 60 years ago, the cast iron used could be expected to have been highly brittle, thus the extent of plastic deformation prior to fracture very small. We have therefore carried out a number of tests on magnesium-modified cast iron with an average elongation of -5 pct. It was hoped that the data obtained from the tests would serve as a guideline for comparing data obtained in tension and bending for brittle materials. Mechanical properties were measured at room temperature on an Instron tensile machine at a crosshead speed of 0.05 in. per min. The three-point bend test employed cylindrical bars 0.20 in. in diameter with a 1.0-in. span. For the tensile test, cylindrical tensile specimens with a gage length of 0.85 in. and a diameter of 0.160 in. were used. Results are summarized in Table I. From Table I one can see that fracture strength

Jan 1, 1965

By J. M. Uys, T. B. King

WalSH, Chipman, King, and rant' have measured the water content (as hydrogen) of actual steel-making slags. An average water content of 290 ppm was found for basic open-hearth tapping slags and 114 ppm for acid open-hearth slags. Upon equilibration of these slags at 1550°C with a 25 pct H20-75 pct Nz atmosphere, the water content increased to about 410 and 300 ppm for the basic and acid slags, respectively. Walsh et al. concluded that an acid slag was thus relatively far removed from equilibrium, and that basic slags showed a closer approach to equilibrium, with the water vapor in the furnace atmosphere. Herasymenko2 contended that these conclusions were unjustified, as the oxygen pressure used in the equilibration experiments, ;bout 5 x X atm, was quite different from that found in the furnace. Consequently, during the experiments the slag composition would have changed due to oxidation of ferrous iron. As an extension of Walsh's work and to attempt to clarify this matter, the solubility of water in a basic open-hearth slag was measured as a function of oxygen pressure. Similar measurements were also made on synthetic silicates in the "Fe0"-Fe203-SiO, system. The experimental technique has been described previously by Walsh et a1.l and Uys and King.3 Samples of the basic open-hearth finishing slag, contained in 10-cc platinum crucibles, were equilibrated at 1550°C with atmospheres of different oxygen pressure but constant water-vapor pressure, Ph~o = 0.192 atm. Calculations, as well as measurements, indicate that this figure approximates the water pressure of the combustion gases in a steam-atomized, oil-fired open hearth. Oxygen pressures in the open hearth can vary from 10"2 atm in the combustion gases to between l0-' and 10" atm in the steel bath. The former figure depends on the combustion practice and the latter on the carbon content and temperature of the bath. The oxygen pressure of the slag should lie somewhere between these extremes and is expected to be closer to that of the steel bath than that of the combustion gases. Oxygen pressures were therefore varied between 10" and 6 x l0 atm. At the lowest pressure the slag "puffed up" when quenched (indicating possible loss of water) so experiments were not conducted at lower oxygen pressures. The results are shown in Fig. 1, which includes the water content of the slag "as sampled". The results show that the water content of the slag increased appreciably on equilibration with water vapor at 0.192 atm pressure and that the water solubility apparently decreases with increased oxygen pressure. The solubilities found are comparable to those of the Li20-Ca0-Si02 system.3 Work with synthetic slags in the "Fe0"-Fe203-SiOz system was performed at 1500" C, with Ph20 = 0.192 atrn and for oxygen pressures varying between 10"2 and 10-lo atm. Samples for chemical analysis were prepared as described by Larson.4 The results are shown in Fig. 2. Some low-silica melts tested at low oxygen pressures "puffed up" when quenched and analyzed less than 100 ppm water; these results are not included in Fig. 2. The melts containing 40 mol pct silica also showed a tendency to "puff up" during the quench, when they were tested at the lowest oxygen pressure. These results indicate that, at constant silica content, the solubility of water decreases somewhat with increased oxygen pressure. The effect is, however, small considering the wide range of oxygen pressures studied. Also, at constant oxygen pressure (above about lom5 atm) the solubility increases

Jan 1, 1963

By Earl Oliver

IN times like these, the A. I. M. E. and similar societies have their greatest usefulness. . . . Individuals and companies acting alone in the development of public opinion are merely voices crying in the wilderness. United and organized they make a great force that can and does influence public action. . . . What part, if any, then, shall the A. I. M. E. take in these great stabilization processes of civilization? Shall it help to give direction and force to scientific knowledge which comes within its field of activity or shall it merely develop more of it? . . . Is it the A. I. M. E.'s function to help bring system, order and direction out of this situation so that the world can again have forward economic movement, or should it rest on its oars until other agenciess develop that public understanding and direction so necessary for economic progress? As we understand the functions of the A. I. M. E. Petro¬leum Division, they are to discover and promote knowl¬edge for the benefit of society on the mining of oil and gas. To the individual member of the Petroleum Division, there are certain advantages of social and professional contacts, but the collective purpose is that described. And the individual is benefited by membership only as the Division measures up to the purposes of its existence. Consequently, the welfare of this Division and that of its members depends on the extent to which it keeps pace with the needs of society on matters relating to the mining of oil and gas.

Jan 1, 1932