Search Documents

By R. A. Salathiel

A new synthetic material has been developed which is highly effective in treating drilling muds to reduce filtration rate. The material is the soluble salt of a very high molecular weight condensation product of sulfonated phenol and formaldehyde (SPIF). Laboratory tests show that SPIF is effective in muds of all salinities varying from fresh water to saturated salt water. Alkaline materials. such as soda ash or caustic and quebracho, may be used in combination with SPIF to advantage, and are essential in muds containing saturated salt water. In a field test where the water used in the mud had a salinity of about one-half that of sea water, SPIF in combination with caustic and quebracho made a very satisfactory mud. SPIF does not ferment. but due probably to additional polymerization a slight decrease in effectiveness is found when it is subjected to high PH and high temperature for a long time. INTRODUCTION Drilling mud is essential in rotary drilling. The influence of variations in the different properties of a mud on its ability to perform the various functions in drilling of wells is thoroughly understood in some cases and poorly understood in others. For instance, the function of mud density in restraining high pressure fluids is simple and well known. On the other hand. while the value of low filtration is widely recognized, it is seldom possible to determine precisely what filtration rate is required for the mud to perform its functions properly. Filtration rate is important because it influences the ease of moving tools in or out of the hole. Filtration rate also affects the stability of the bore hole walls, which are subject to softening and degradation by aqueous filtrate. Difficulties in rotary drilling are often avoided by using low-filtration muds. Treatment of fresh-water muds to provide moderately low filtration rates usually consists of adding chemicals to improve the dispersion of the clays. To provide very low filtration rates, organic colloidal materials are added. Among the materials hat are used in this way are starch, natural gums, and altered celluloses. In muds that contain large amounts of salt or calcium or magnesium ions, the clays are coagulated and, as a consequence, the filtration rate is undesirably high. In such muds organic colloids are of great importance. LIMITATIONS OF PRESENT FILTRATION ADDITIVES Starch and water-soluble gums are widely used as filtration control agents. Starch is the most important material of this kind being used. It has the advantage of relatively low cost. It is effective in promoting low filtration rates, not only in fresh water muds, but also in muds containing large amounts of salts. However, both starch and natural gums are subject to fermentation and must be preserved from damage caused by microbiologic attack. Also, both starch and natural gums tend to increase the mud viscosity undesirably. Furthermore, the quantity of material required may be quite large. This is especially true when substantial amounts of salts are present. In such a case small addition* of starch may increase rather than reduce the filtration rate of the mud. Carboxy-methyl-cellulose, a chemically altered form of cellulose, has some advantages over starch. It is effective in smaller concentrations and does not increase the viscosity as much as

Jan 1, 1952

By J. G. Y. Chow, S. B. McRickard

The tensi1e properties of Ferrovac iron have been studied from 4° to 300°K. The stress required for macroscopic yielding was found to he constant below approximately 50°K. The effect of mechanical twinning on this low -temperature stress plateau was investigated. The onset of twinning occurs in this iron between 130° and 150°K and depending on its previous thermal history the twinning-stress curue may drop below or remain above the vield-stress curves as the temperature is lowered. Twinning has been shown to initiate slip in quenclzed iron at low temperatures. In no instances, however, did the onset of twinning alter the continuity of the yield stress -tempwature curve. Our data shows that carbon inhibits twinning and slip at low tem-peratures. This observation nay be used to explain the ductile-to-brittle transition in iron. The effect of fast neutron irradiation on yielding and embrittlement in iron and Fe-C alloys is offered as supporting evidence for this viewpoint. THE mode of yielding in iron at low temperatures was studied in an attempt to find an expression based on a single mechanism to describe the thermal dependence of the yield stress of iron. There are two types of inflections observed in the variation of the yield stress with temperature in iron and Fe-C alloys. The first is associated with ductile behavior and consists of a region extending 50" to 100°K above absolute zero in which the yield stress is independent of temperature. The second is observed in more brittle materials such as Fe-C alloys and irradiated iron and consists of an abrupt discontinuity in the yield curve as the temperature is lowered through a ductile-to-brittle transition point. The temperature dependence of the yield stress for iron with four grain diameters as found in this study is shown in Fig. 1. To varying degrees all the curves appear to flatten or approach an asymptotic value as the temperature is lowered below 50°K. Several other investigators1,2 have observed a plateau in the yield stress of iron and steel at low temperatures and in 1956 Louat3 presented a theory which contained an explanation for this behavior. In a subsequent exchange with Erickson and Low4'5 who attributed the plateau to the onset of mechanical twinning Louat8 showed that twinning first occurs in iron and steel tested in tension at temperatures as high as 140°K which is well above the observed plateau in yield stress. Furthermore he pointed out that both twinning and slip are basically dislocation processes and that with modified parameters his original theory still applied when deformation is initiated by twinning. Variables which affect the ductile-to-brittle transition in iron are test temperature, strain rate, composition and grain size.7 LOW,8 Hahn et al.,9 and Hull10 have provided evidence which links brittle fracture at a given temperature with the specimen grain size and the onset of twinning. In fact, Hull equates the brittle fracture stress to the twinning stress. On the other hand brittle fracture has been observed in the absence of twinning and priestnerl1 has given a fracture criterion which is valid whether or not fracture is preceded by extensive twinning. The data presented here clarify the role of twinning in the low-temperature deformation of iron. Strong evidence is given that the amount and distribution of interstitial impurities such as carbon are of

Jan 1, 1965

By J. B. Clark, A. S. Yue

The zone-melting technique can be adapted for the de-termination of the eutectic composition in complex metal systerrzs. The application of this method is demonstrated in a simple eutectic system, Mg-AE, in which the eutectic composition is known and in a complex ternary system, Mg-Al-Zn, in which the literature is uncertain as to the composition of the ternary eutectic. The advantages and limitations of this unique approach for the determirution of the eutectic composition are discussed. ThE eutectic composition in phase diagrams is usually determined by thermal analysis of a series of arbitarily selected alloy compositions. The temperatures of the liquidus and eutectic arrests for each alloy are plotted and the eutectic composition is estimated by extrapolation to the entectic temperature of the curve formed by the liquidus arrest temperatures for the series of alloys. Although this approach readily yields the eutectic temperatures, several dekrminations are needed to estimate the eutectic composition, even in a simple system. In a complex ternary system, a great many determinations are often necessary to estimate, even approximately, the ternary eutectic composition. Thus, the conventional method is inherently tedious and time consuming. The application of zone melting provides a relatively efficient method of determining the eutectic composition.' As an illustration, consider the zone melting of an alloy composition C, in the simple eutectic system A-B, shown in Fig. 1, under the ideal conditions of infinitely rapid diffusion in the liquid, no diffusion in the solid, and ease of nucleation of both phases. As the zone moves along the bar, the composition of the zone is enriched by solute rejected during the freezing of the a phase and the zone composition approaches the eutectic composition CE.Once the zone composition attains the lowest melting composition, i.e., the eutectic composition, it remains at this composition as the zone moves along the bar and finally freezes as such at the end of the bar. Chemical analysis of the end of such a zone-melted bar then should yield the eutectic composition CE of the system A-B. A corresponding analysis can be made for a ternary eutectic system. Under the ideal conditions noted above, only one pass of the molten zone is required to yield the eutectic composition. Experimentally, however, a solute-rich layer forms at the solid-liquid interface2 and the composition of the zone does not attain the eutectic composition as rapidly or as uniformly as in the ideal case outlined above. But with agitation of the melt, the ideal conditions can be approximated experimentally. Also, as shown below, zone melting permits a cumulative build-up of the solute at the end of the bar to the eutectic composition. The purpose of this paper is to demonstrate this unique method for determining the eutectic composition. The method is here applied to two systems: first, to the binary Mg-A1 system, in which the composition is well established, and second, to the complex Mg-Al-Zn system in which there is doubt concerning the composition of the ternary eutectic. EXPERIMENTAL PROCEDURE The zone-melting apparatus used in this study is described in detail elsewhere.3 Briefly, the binary alloy rods (5/8 in. in diam and 9 in. long) and the ternary alloy rods (5/8 in. in diam and 6 in. long), with the compositions given in Table I, were zone

Jan 1, 1962

By AIME AIME

FREDERICK WORTHEN BRADLEY, the newly elected president of the Institute, may be said to be the prototype of the men who have built up the great mining industry of the West. He was born in Nevada County, Cal., on Feb. 21, 1863, and studied mining at the University of California from 1882 to 1884, as a member of the Class of 1885. He was in contact with the mining industry from his earliest years and in his reminiscences which we published last month, he told of meeting Thomas Mein and H. C. Perkins in 1877. Beginning as assayer and roustabout at the Eagle Bird mine, in Nevada county, Mr. Bradley was a deputy mineral surveyor in 1886 and 1887 and superintendent of the Spanish mine from 1885 to 1890. There he made a record of mining gold ore at 65 cents per ton that was not only astounding in that day when modern large scale mining had not yet been developed but is still a mark to shoot at. As a result he was called in 1890 to be assistant manager of the Bunker Hill and Sullivan and was made manager in 1893. In 1897, he was elected to the presidency of the company, a position he still holds. H. C. Perkins and D. O. Mills, the largest stockholders in the Bunker Hill and Sullivan Co. took over the Tacoma smelter in 1898, feeding it with concentrate from the Coeur d'Alene and Douglas Island mines but also doing a gen-era1 smelting business. Mr. Bradley was put in as president of the Smelting company, and held that position until the plant was sold to the American Smelting Securities Co. in 1905.

Jan 1, 1929

By AIME AIME

THE following paragraphs comprise such information as the Secretary has been able to obtain concerning the members and associates whose deaths have been reported. Further particulars or corrections of errors, and biographical data concerning deceased members or associates not already noticed in this way, are solicited. Pat Doyle was born in 1849. At the age of fifteen he entered the Civil Engineering College of Madras, India, and left it at seventeen, having achieved special distinction in mathematics, chemistry,. and geology. Before be was eighteen years old he was in charge of two of the most important Sub-Divisions in the Madras Presidency, where he had ample opportunities for acquiring a preliminary knowledge of his profession, which was his chief object in joining the Public Works Department. In 1867, his energetic measures saved the island of Seringham from disastrous inundation. At this period he began contributing to the press ; and after a varied practical experience he came into public notice again in 1876, with an article in the Colliery Guardian on Indian Mines and Mining. In 1877 he became a Fellow of the Statistical Society of London. He was a founder of the Straits Branch of the Royal Asiatic Society and a life member of the parent Society of Great- Britain and- Ireland, as well as a member of the Independent Asiatic Society of Bengal. In 1878-9 he was Chief Superintendent of the Public Works of Perak; was active in having the Associate Member Class added to the Institution of Civil Engineers; and became a member of the Society of Engineers of London and of the North of England Institute of Mining and Mechanical Engineers. In 1880 he went to the Southern Colonies and held several appointments in Australia, where he became a member of the Johnsonian Club, Brisbane, and the Queensland Philo-

Jan 5, 1908

By JOHN BIRKNBINE

MR. NEILSON was born Aug. 12, 1842, at Philadelphia, Pa., where he died Dec. 30, 1906. His business career began with his graduation, in the class of 1862, from the Polytechnic College of the State of Pennsylvania. For a short time after graduation he was instructor in mathematics at the college, and then became associated with Messrs. Booth & Garrett, chemists, of his native city: In 1867 he was sent to the Adirondack mountains to care for mining interests of the late Jay Cooke, and spent about three years there, operating the forges at Elizabethtown, Essex county, N. Y. He also prepared an interesting monograph on Catalan forges and their operations. In 1868 he published a chart showing the material progress of the United States, and the cost of certain staple products during a series of years, which is believed to be the first of its kind issued in this country. In 1870 he made a trip to the Pacific Coast, prior to entering the service of the Pennsylvania Steel Company. In 1871, when the Logan Iron & Steel Co., of Burnham, Pa., failed, Mr. Neilson was appointed receiver, re-organized the company, became' its General Manager, and spent more than four years in this work. In the meantime, he became interested in the Freedom forge of the same place, and, with Mr. Wm. Burnham and Mr. Milton Brosius, laid the foundations for what is now the Standard Steel Works. From Jan. 1, 1877, to April 1, 1890, he was General Manager of these works, and closely associated with the Baldwin Locomotive Works. In 1878 he was in charge of the first consignment of Baldwin locomotives to Europe, which, with a picked crew of men from Baldwin's, he took to Eydtkennen, Russia, and placed in service. In 1890 he resigned from the Standard Steel Works and ac-

Jul 1, 1907

By R. H. Wightman, G. H. ADAM

In order to secure good results in the prevention of accidents, it is generally recognized that the desire for such accomplishment, as well as the aggressive and constructive action to achieve it, must emanate from the Top Management and permeate successively down through the "Chart of Authority" to the workmen. Several years ago, with the above as a basis and with full support of the Top Management, the Mining Department started a program of selling the foremen and bosses the idea that safety could be achieved and that it was desired and required. Using psychology, persistence and numerous other methods, the foremen and bosses were finally impressed with the idea that "It can be done" and "It will be done." With this in mind, new ideas were brought forth by the foremen and bosses regarding the caving operation and the specific jobs in the operation. These new ideas were taken up in round-table discussions and resulted in certain changes in the undercutting method and the actual drawing of the blocks. These changes resulted in increasing fragmentation of the blocks which prevented the usual hang-up areas in the blocks. With the rock smaller in size and within reasonable reach from the tapping drifts, accidents were prevented in the tapping section. At the same time, an enforced campaign of housekeeping throughout the mine was undertaken with very beneficial results. The foremen and bosses then, in turn, educated and trained the workers themselves to become safely conscious. In so doing, a constant re- minder was given on all jobs assigned that the job was to be done safely as well as efficiently. No man is assigned a job who is not qualified for the type of work required. Efficiency and safety go hand in hand.

Jan 1, 1949

The mining fraternity of North America was grieved and shocked to learn of the death of Dr. Willet G. Miller on Feb. 10, 1925. Doctor Miller was for many years the Provincial Geologist of Ontario and the one who more than any other had contributed by his personal work and the reports of his subordinates to the recent extraordinary mineral development of the Province. Doctor Miller was fifty-eight at the time of his decease. A man of unusually stalwart physique, he seemed destined to many years of useful service. His friends in both the American and Canadian Mining Institutes can with difficulty reconcile themselves to his loss. Doctor Miller was born in 1867 in Port Rowan, Ont., on the shores of Lake Erie. After preparation in the high school of his native town, he entered the University of Toronto and took his bachelor's degree in 1890. He pursued graduate studies in geology at Chicago, Harvard, and Heidelberg Universities. In 1893, he was first appointed lecturer and soon thereafter Professor of Geology in Queens University, Kingston, Ont., a chair which he held until 1902. He was then appointed Provincial Geologist of Ontario and was placed at the head of the Survey which was attached to the Department of Mines. Within the next year, 1903, he performed the service that made him famous. In the summer of 1903, in connection with the building of the Ontario Government Railway toward an objective on James Bay, veins had been noticed by construction parties just north of what is Cobalt Lake today, and in the rocky pass that is now traversed by the main line of the Canadian National Railway en route to Vancouver. The pink stain of cobalt bloom on the vein, known later as La Rose, caught the eye of a workman; in November, Doctor Miller recognized the silver in it, and brought the possibilities of the district to general attention. In December, he published an article in the Engineering and Mining Journal, stating that the veins could be worked at a handsome profit. During the winter and spring, the mining interest awoke, which resulted in the astonishingly productive silver district of Cobalt; but in which, Doctor Miller, because a government official, scrupulously refrained from having any financial interest whatever. Seldom has so high a sense of honor been manifested; and as the result, Doctor Miller commanded confidence and respect to an extraordinary degree. Hard on the discoveries at Cobalt came, in the next few years, those at the other famous camps in Northern Ontario; and step by step with them, reports issued from

Jan 1, 1925

By Ernest G. Enck

"The Rockets' Red Glare" of the Fourth of July is produced by strontium compounds. However, strontium has a number of less spectacular uses; i.e. in, or in connection with, the manufacture of ceramics, caustic soda, glass, railway and truck signal flares, beet sugar and steel. The principal ore of strontium for use both as the mineral and for production of compounds is celestite (SrSO4). This mineral varies in color from white to pink or blue depending on presence of impurities. It has a hardness of about 3.5 and specific gravity of 3.9. It is brittle and has perfect basal and prismatic cleavages. The high grade ore is obtained from England, hence it has become the standard for all other producing areas. (See analyses, Table 1.) The most objectionable impurity in English celestite is iron, coming mostly from adhering clay. On the other hand, Mexican celestite, while no higher in strontium sulfate content, is extremely low in iron (less than 0.2 pct), hence it is more desirable for certain uses. Most of the celestite in Spain and in the United States is high in calcium and barium, and commonly high in iron, and requires some form of beneficiation in order to be equal to English ore. The natural carbonate (SrCO3), or strontianite, is less important than celestite as a source of strontium, because it is less abundant and is not so widespread in its occurrence. Furthermore, it generally occurs with calcite (CaCO3) and lead sulfide (PbS), and for most uses these impurities are detrimental. This mineral is generally white or yellowish, forming needle-like crystals. It has a hardness of about 3.7 and a specific gravity of 3.68-3.8. The mineral is brittle and has an imperfect cleavage. A typical analysis of German strontianite is shown in Table 1. [ ] Distribution of Deposits UNITED STATES Occurrences of strontium minerals are known in Arkansas, Arizona, California, Illinois, Ohio, Pennsylvania, Tennessee, Texas, and Washington. Celestite occurs in the Vulture Mountains, Maricopa County, Arizona in beds three to ten feet thick associated with sandstone, gypsum, and barite. Because of the low strontium content, approximately 86 pct SrSO4, it has no commercial value. A large deposit of celestite occurs in San Bernardino County, California, in the Cady Mountains near Argus Station, about eight miles west of Ludlow. The celestite here is interbedded with shaly and clayey tuff in a zone about 300 ft thick. Massive, finely crystalline ore has been recovered with an analysis

Jan 1, 1960

Silver ore was first discovered in 1866 at Manhattan, and a few ore shipments were treated in a mill at nearby Belmont. The district was abandoned from 1869 to April 1, 1905, when rich gold float was discovered on what was to be called the April Fool claim. By early 1906, 4, 000 people lived in Manhattan. The San Francisco earthquake, in April of 1906, caused the withdrawal of capital from Manhattan and most of the mines were shut down. Later that year and in 1907, however, more strikes were made. The camp prospered until the mid-1920s, but a steady production of several hundred thousand dollars per year was sustained even during the great depression. Then, in 1939, Nevada's first bucket-line dredge was installed below the town and operated until 1947, producing $4.6 million in gold. The Houston International Minerals operation at Manhattan was started in July of 1980 at a throughput of about 545 mt per day (600 st per day). In contrast to the early day underground operations, Houston's mine is open-pit and processes low-grade disseminated ores. The ore is a metamorphic schist containing 2. 7 g Au and 1. 03 g Ag per mt (0. 08 oz Au and 0. 03 oz Ag per st). Some coarse gold, up to 1 mm in size, is present. Mining and haulage is done by a contractor. Stockpiled mine-run ore is crushed in three stages comprising a jaw crusher and two cone crushers, with screens ahead of the cone crushers. Crushed product, at about 19 mm (3/4 in.) size, is stored in a silo. Grinding is by single stage ball mill with the discharge passing over two hydraulic traps for coarse gold removal. These traps will be replaced in late 1980 by a two-cell Pan American jig treating the cyclone underflow. The jig hutch product, along with the hydraulic trap product that has been stored, will be treated further for gold recovery. The gravity tails will then be cycloned with the underflow being recirculated in the ball mill and the overflow being treated by flotation. A rougher concentrate is made in twelve No. 48 Galigher cells with the float tails being cycloned. Cyclone underflow is refloated in another four No. 48 cells; the overflow is treated in sluice boxes for further gold recovery before being sent by gravity to the tailings pond. Bulk flotation concentrates are cleaned three times with the final concentrate being thickened. The thickener underflow is then batch cyanided in mechanically agitated tanks and washed with barren liquor

Jan 1, 1981

Edmund Gybbon SpilsbURy, mining and metallurgical engineer of international reputation, died suddenly of heart failure on May 28, 1920, in the New York Eye and Ear Infirmary, following an operation for cataract, which had been successfully performed a few days before. Mr. Spilsbury was one of the early members of the American Institute of Mining Engineers, which he joined in 1873. During all this time he contributed freely of his time and ability. He was manager of the Institute from 1885 to 1887, vice-president, 1893 and 1894, and president in 1896. He was also a member of the Engineers Club, of which he was president in 1916 and 1917, American Society of Civil Engineers, American Society of Mechanical Engineers, Institution of Mining and Metallurgy, Mining and Metallurgical Society of America, American Electrochemical Society and the Rocky Mountain Club of New York. He was a trustee of the United Engineering Society from 1916 to his death; a member of United Engineering Society Library Board from its organization in 1913 until his death, being its chairman from 1918 to January, 1920; a trustee of Engineering Foundation Board from 1916 until his death; and member of the John Fritz Medal Board of Award. He was also a member of the Division of Engineering of the National Research Council. Born in London, England, in 1845, Mr. Spilsbury went to Liege, Belgium, at an early age, where he received his preliminary education. For his technical education he attended the University of Louvain, Belgium, graduating in 1862, and later he took a practical course at Clausthal, Germany. In 1864 he became assistant engineer for the Eschweiler Zinc Co., of Stolberg, one of the largest miners and smelters of lead and zinc in the world at that time, and the next year he took charge of that company's mines and works on the Island of Sardinia. From Sardinia he went to the Atlas Mountains in Morocco. In 1867 he entered the service of McClean & Stilman, of London, and had charge of the construction of the iron gates for the Surrey Commercial Docks. In 1868 he was designing engineer with J. Casper Harkort, and had charge of most of the detail work of the Keulenberg Bridge in Holland, the Danube Bridge in Vienna, and the Rhine Bridge at Düsseldorf. In 1870 Mr. Spilsbury came to the United States to investigate the lead and zinc resources for the Austro-Belgian Metallurgical Co. After spending two years in this work, he resigned in order to practice in the United States, and he was the first to introduce the Harz system of ore

Jan 1, 1922

Edmund Gybbon SpilsbURy, mining and metallurgical engineer of international reputation, died suddenly of heart failure on May 28, 1920, in the New York Eye and Ear Infirmary, following an operation for cataract, which had been successfully performed a few days before. Mr. Spilsbury was one of the early members of the American Institute of Mining Engineers, which he joined in 1873. During all this time he contributed freely of his time and ability. He was manager of the Institute from 1885 to 1887, vice-president, 1893 and 1894, and president in 1896. He was also a member of the Engineers Club, of which he was president in 1916 and 1917, American Society of Civil Engineers, American Society of Mechanical Engineers, Institution of Mining and Metallurgy, Mining and Metallurgical Society of America, American Electrochemical Society and the Rocky Mountain Club of New York. He was a trustee of the United Engineering Society from 1916 to his death; a member of United Engineering Society Library Board from its organization in 1913 until his death, being its chairman from 1918 to January, 1920; a trustee of Engineering Foundation Board from 1916 until his death; and member of the John Fritz Medal Board of Award. He was also a member of the Division of Engineering of the National Research Council. Born in London, England, in 1845, Mr. Spilsbury went to Liege, Belgium, at an early age, where he received his preliminary education. For his technical education he attended the University of Louvain, Belgium, graduating in 1862, and later he took a practical course at Clausthal, Germany. In 1864 he became assistant engineer for the Eschweiler Zinc Co., of Stolberg, one of the largest miners and smelters of lead and zinc in the world at that time, and the next year he took charge of that company's mines and works on the Island of Sardinia. From Sardinia he went to the Atlas Mountains in Morocco. In 1867 he entered the service of McClean & Stilman, of London, and had charge of the construction of the iron gates for the Surrey Commercial Docks. In 1868 he was designing engineer with J. Casper Harkort, and had charge of most of the detail work of the Keulenberg Bridge in Holland, the Danube Bridge in Vienna, and the Rhine Bridge at Düsseldorf. In 1870 Mr. Spilsbury came to the United States to investigate the lead and zinc resources for the Austro-Belgian Metallurgical Co. After spending two years in this work, he resigned in order to practice in the United States, and he was the first to introduce the Harz system of ore

Jan 1, 1922

By Wilson D. Michell

The Magma copper vein trends east-west, dips 70" south, and cuts through a 6000-ft thickness of limestones, quartzites,. shale, diabase, and schist. The vein is itself a fault with a horizontal offset of 500 ft on the formation contacts in the two walls. There are two principal faults of large displacement and numerous smaller steep and flat faults that complicate the prediction of ore occurrence. A study of the geology, its systematic recording to facitliate ready reference, and graphic methods of interpretation of mineralization have aided the exploration, development, 2nd mining of the ore. In making predictions of the distribution of mineable ore bodies and their shape in critical areas, studies are made of "mineralization contours" and "mineralization trends," which are developed on a longitudinal section of the vein from variations in the concentration of the combined base metal content as shown by assays of available openings in the mine. Introduction This paper describes an example of geological work applied directly to mining and exploration problems in a deep vein deposit, and it is presented as being of interest especially to those engaged in working more or less similar veins. In 1944 to 1945 the writer spent a year as assistant to J. K. Gustafson in a thorough geological examination of the Magma mine. Much of the writer's subsequent independent work described in the present paper had its inception in ideas originated by Gustafson during that examination. Objectives of Geological Work at Magma Mine The objectives of geological work at Magma, as at operating vein mines of a similar nature, can be summarized as follows: 1. Direct assistance to the mining department by means of predictions as to the size, shape, grade, and location of ore bodies; by solution of fault problems and irregularities in the veins; by prepara-?ion of detailed ore-reserve estimates in specific areas; by keeping a complete record of the geology and assay results in the mine; and by guiding development work. In short, geology can aid in the realization of the prime purpose of the mining department, which is that of producing the greatest amount of ore in the most economical and expeditious manner possible. 2. Guidance for exploration, especially diamond drilling, in undeveloped areas of the mine. 3. Contributions to the understanding of the general geology of the deposit and its regional setting, including ore genesis, structure, and mineral relationships. Magma Ore Deposit The east-west trending Magma vein, dipping about 70" south, cuts through a 6000-ft thickness of concordant limestones, quartzites, shale, diabase, and schist, named in descending order. These

Jan 1, 1949

James Douglas will long be remembered as a distinguished mining engineer and metallurgist, as a scientist with broad vision, as an executive whose understanding of practical problems coupled with his knowledge of men and affairs enabled him to weld together great mining interests and to their service build railroads and bring power. More, he will be recalled as a philosopher and a writer of charm, a historian of no mean order, and one whose catholic tastes and enthusiasms led him into the fields of education, medicine and theology. His aim was to possess that which he considered made life worth while—friends and effectiveness in whatever task he undertook. In this aim he was successful to a degree exceeded by few, as thousands of his friends and associates could and can testify. Dr. Douglas was born on November 4,1837, at Quebec, Canada. His father, James Douglas, Sr., was a prominent physician and the leading surgeon of Canada. He also established the first retreat for the insane in the Dominion, the Quebec Lunatic Asylum, to which he devoted his services for years; The son followed in the footsteps of his father and studied medicine, not only in Canada but also in Scotland and in Germany. He entered the University of Edinburgh in 1855 but after two years at that institution returned to Canada and was graduated from Queens university at Kingston, Ontario, .with the degree of Bachelor of Arts. Later he went to Lava1 University, Quebec, and subsequently became professor of chemistry at Morrin College, Quebec. After he was graduated—at the time he considered his formal education completed—he traveled with his father in Europe and in the Orient; visiting Egypt, being especially interested in that country, several times. They gathered together an important archaeological collection which later was donated by them to the Metropolitan Museum of Art in the city of New York. James Douglas was also greatly interested in photography, a hobby in which he made use of his chemical knowledge. The writer can remember distinctly the descriptions he gave more than forty years ago in Arizona of the difficulties he encountered with the old wet photographic plates, especially while traveling in Egypt, when he prepared and used his own chemicals. In his humorous manner he told how he once discovered, in the nick of time, the nurse preparing to give the baby in the party a rub-down, using for that purpose the white, limpid

Jan 1, 1934

By W. J. Reagan

IN a study of the life of ingot molds, it is essential to eliminate all of the variables. In the commercial manufacture of steel this is almost an impossibility. In this study many of the variables have been eliminated, and because of the unusually consistent furnace practice, with small variations in the type of steel manufactured, and a similar type of mold design for all ingot sizes, it is possible to determine with some degree of accuracy the cause of variations in ingot-mold life. All of the ingot molds in this study were used in the production of basic open-hearth killed steel with chemical analyses within the following range: C, 0.50-0.85 per cent; Mn, 0.60-0.80; Si, 0.20-0.30; S, 0.04 max.; P, 0.04 max. All ingot molds were of the closed-bottom type and used for bottom casting only. None of the molds in the study failed from cutting of the sides due to top casting; in fact, on only rare occasions are any molds used for top casting. The general type of this mold is shown in Fig. 1. All sizes have rather a heavy band of metal, about 6 in. wide, at the top to give mechanical strength at this point, and all have cast lugs. Cross sections of the vari-ous sizes from top and bottom sections are shown in Fig. 2. Ratios of wall thickness to ingot weight, ratio of ingot diameter to ingot length, and other figures of interest are shown in Table 1. In. the majority of cases, the cause of failure in this type of mold is due to heavy fire cracking on the "flats" at a point from 3 to 6 in. from the bottom radius of the mold. Fig. 3 pictures this type of failure. The start of failure at these points usually begins with a very small section of the interior surface becoming involved. As a rule, a section of 1 or 2 sq. in. is the first noticeable 'indication that mold failure is taking place. Gradually the small section increases until a sizable cavity develops, causing a protuberance on the bottom of the ingot, which eventually becomes too large to be stripped. The mold is then removed from service. At the time of failure, this cavity often reaches a size of about 5 sq. in. and about 1/2 in. deep. Sometimes cavities are found on only two or three sides and at other times all twelve sides appear to be involved.

Jan 1, 1936

By Wilson D. Michell

The Magma copper vein trends east-west, dips 70" south, and cuts through a 6000-ft thickness of limestones, quartzites,. shale, diabase, and schist. The vein is itself a fault with a horizontal offset of 500 ft on the formation contacts in the two walls. There are two principal faults of large displacement and numerous smaller steep and flat faults that complicate the prediction of ore occurrence. A study of the geology, its systematic recording to facitliate ready reference, and graphic methods of interpretation of mineralization have aided the exploration, development, 2nd mining of the ore. In making predictions of the distribution of mineable ore bodies and their shape in critical areas, studies are made of "mineralization contours" and "mineralization trends," which are developed on a longitudinal section of the vein from variations in the concentration of the combined base metal content as shown by assays of available openings in the mine. Introduction This paper describes an example of geological work applied directly to mining and exploration problems in a deep vein deposit, and it is presented as being of interest especially to those engaged in working more or less similar veins. In 1944 to 1945 the writer spent a year as assistant to J. K. Gustafson in a thorough geological examination of the Magma mine. Much of the writer's subsequent independent work described in the present paper had its inception in ideas originated by Gustafson during that examination. Objectives of Geological Work at Magma Mine The objectives of geological work at Magma, as at operating vein mines of a similar nature, can be summarized as follows: 1. Direct assistance to the mining department by means of predictions as to the size, shape, grade, and location of ore bodies; by solution of fault problems and irregularities in the veins; by prepara-?ion of detailed ore-reserve estimates in specific areas; by keeping a complete record of the geology and assay results in the mine; and by guiding development work. In short, geology can aid in the realization of the prime purpose of the mining department, which is that of producing the greatest amount of ore in the most economical and expeditious manner possible. 2. Guidance for exploration, especially diamond drilling, in undeveloped areas of the mine. 3. Contributions to the understanding of the general geology of the deposit and its regional setting, including ore genesis, structure, and mineral relationships. Magma Ore Deposit The east-west trending Magma vein, dipping about 70" south, cuts through a 6000-ft thickness of concordant limestones, quartzites, shale, diabase, and schist, named in descending order. These

Jan 1, 1949

ARTICLE I NAME AND OBJECT SEC. 1. This Institute is incorporated under the Membership Corporations law of the State of New York; its corporate name is American Institute of Mining and Metallurgical Engineers, Inc.; and its objects are such as are stated in its Certificate of Incorporation. ARTICLE II- MEMBERS SEC. 1. The membership of the Institute shall comprise four classes, namely: 1. Members; 2. Honorary Members; 3. Associates; 4. Junior Associates. All members shall be equally entitled to the privileges of membership, excepting that Honorary Members, Junior Associates, and Members and Associates whose residences shall be outside of the United States, Mexico, and Canada shall not e entitled to vote. Members and Associates residing within the United States of America, Mexico, and Canada, and not in arrears for dues, shall be entitled to vote in person at the meetings of the Institute, or, as hereinafter provided for, by letter ballot. SEC. 2. Members shall comprise all those persons who on the third Monday of February, 1918, were members of the Institute, and in addition thereto, all those thereafter elected or transferred into the class of Members. A person to be eligible for election or transfer into the class of Members must be at least 27 years of age and must have had at least six years' employment in the practice of-engineering, mining, geology, metallurgy or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. Graduation from the scientific course of a college, approved by the Committee on Membership, shall be considered equivalent to two years' employment, as required in the previous sentence. Employment as a teacher of engineering, mining, geology, metallurgy or chemistry, if in direct charge, may be considered a position of responsibility as specified in the second paragraph. Persons employed in research or any scientific literary work or in teaching in the scientific departments of colleges, approved by the Committee on Membership, who at the same time are engaged in consulting or in the active practice of mining, geology, or metallurgy, shall be entitled to consider the time so spent in active practice as equivalent to an equal length of time of employment in positions of responsibility, . provided the work done or the positions held seem to the Committee on Membership to warrant the. equivalency. The requirement of three years' employment in positions of responsibility may be waived by the Committee on Membership in the case of persons who have done notable original work in mining,. geology, or metallurgy, or have won distinction by

Jan 1, 1925

ARTICLE I NAME AND OBJECT SEC. I. This Institute is incorporated under the Membership Corporations law of the State of New York; its corporate name is American Institute of Mining and Metallurgical Engineers, Inc.; and its objects are such as are stated in its Certificate of Incorporation. ARTICLE II MEMBERS SEC. 1. The membership of the Institute shall comprise four classes, namely: 1. Members; 2. Honorary Members; 3. Associates; 4. Junior Associates. All members shall be equally entitled to the privileges of membership, excepting that Honorary Members, Junior Associates, and Members and Associates whose residences shall be outside of the United States, Mexico, and Canada shall not be entitled to vote. Members and Associates residing within the United States of America, Mexico, and Canada, .and not in arrears for dues, shall be entitled to vote in person at the meetings of the Institute, or, as hereinafter provided for, by letter ballot. SEC. 2. Members shall comprise all those persons who on the third Monday of February, 1918, were members of the Institute, and in addition thereto, all those thereafter elected or transferred into the class of Members. A person to be eligible for election or transfer into the class of Members must be at least 27 years of age and must have had at least six years' employment in the practice of engineering, mining, geology, metallurgy or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. Graduation from the scientific course of a college, approved by the Committee on Membership, shall be considered equivalent to two years' employment, as required in the previous sentence. Employment as a teacher of engineering, mining, geology, metallurgy or chemistry, if in direct charge, may be considered a position of responsibility as specified in the second paragraph. Persons employed in research or any scientific literary work or in teaching in the scientific departments of colleges, approved by the Committee on Membership, who at the same time are engaged in consulting or in the active practice of mining, geology, or metallurgy, shall be entitled to consider the time so spent in active practice as equivalent to an equal length of time of employment in positions of responsibility, provided the work done or the positions held seem to the Committee on Membership to warrant the equivalency. The requirement of three years' employment in positions of responsibility maybe waived by the Committee on Membership in the case of persons who have done notable original work in mining, geology, or metallurgy, or have won distinction by

Jan 1, 1925

By W. J. Reagan

In a study of the life of ingot molds, it is essential to eliminate all of the variables. In the commercial manufacture of steel this is almost an impossibility. In this study many of the variables have been eliminated, and because of the unusually consistent furnace practice, with small variations in the type of steel manufactured, and a similar type of mold design for all ingot sizes, it is possible to determine with some degree of accuracy the cause of variations in ingot-mold life. All of the ingot molds in this study were used in the production of basic open-hearth killed steel with chemical analyses within the following range: C, 0.50-0.85 per cent; Mn, 0.60-0.80; Si, 0.20-0.30; S, 0.04 max.; P, 0.04 max. All ingot molds were of the closed-bottom type and used for bottom casting only. None of the molds in the study failed from cutting of the sides due to top casting; in fact, on only rare occasions are any molds used for top casting. The general type of this mold is shown in Fig. 1. All sizes have rather a heavy band of metal, about 6 in. wide, at the top to give mechanical strength at this point, and all have cast lugs. Cross sections of the various sizes from top and bottom sections are shown in Fig. 2. Ratios of wall thickness to ingot weight, ratio of ingot diameter to ingot length, and other figures of interest are shown in Table 1. In the majority of cases, the cause of failure in this type of mold is due to heavy fire cracking on the "flats" at a point from 3 to 6 in. from the bottom radius of the mold. Fig. 3 pictures this type of failure. The start of failure at these points usually begins with a very small section of the interior surface becoming involved. As a rule, a section of 1 or 2 sq. in. is the first noticeable indication that mold failure is taking place. Gradually the small section increases until a sizable cavity develops, causing a protuberance on the bottom of the ingot, which eventually becomes too large to be stripped. The mold is then removed from service. At the time of failure, this cavity often reaches a size of about 5 sq. in. and about 1/2in. deep. Sometimes cavities are found on only two or three sides and at other times all twelve sides appear to be invoIved.

Jan 1, 1937

By A. A. Bauer, M. S. Farkas, F. A. Rough

An investigation of the d-phase relationships between the uranium-zirconium and uranium-molybdenum systems was conducted. A ternary cut joining U-31.5 at. pct Mo to U-74 at. pct Zr is presented on the basis of differential thermal analysis, metallographic and X-ray diffraction data. HyDothetical isothermal ternary sections, inferred from the determined d-phase relationships, are presented for the uraniztm-zirconium-molybdenum system. A ternary eutectoid, at 454ºC, was found in zirconium-rich alloys. Its composition, based on metallography and electron-beam micro-analysis, is estimated as U-61.7 at. pct Zr-7.1 at. pct Mo. URANIUM binary systems have been studied extensively in the past to supply basic information needed in reactor-fuel development. Alloys of uranium with zirconium, molybdenum, and titanium are of particular interest because, in these binaries, extensive or complete solid solubility between the body-centered-cubic forms of these elements and y uranium exists. In addition, an intermediate phase of limited solid solubility forms in each of these systems by transformation of the high-temperature ?-uranium phase. Previous investigation of the phase relationships existing between the intermediate 6 phases in the uranium-zirconium-titanium and the uranium-molyb- denum-titanium ternaries have already been reported.1,2 The results of an investigation of the phase relationships existing between the 6 phases in the uranium-zirconium-molybdenum system is reported here. The phase equilibria that occur in the solid-state portions of the pertinent binary systems are shown in Fig. 1. Phase nomenclature appearing throughout the report is as shown in these diagrams. The crystal structure of the phases in this system are given in Table I. EXPERIMENTAL PROCEDURES Alloys were cast and fabricated to 1/4-in.-diam rod. Specimens were heat treated and examined by metallographic and X-ray techniques. Thermal-analysis data were obtained.

Jan 1, 1960