Search Documents

By John Wulff, J. H. Hollomon

Service failures in brass condenser tubes are often due to corrosion. One of the commonest types of corrosion reveals a surface structure of redeposited copper.' The study of the effect of alloy addition agents in preventing this kind of corrosion has received impetus from the extensive publication of Bengough and May.2 The mechanism of such inhibition gauged from immersion corrosion,2 cell corrosion,3 and electrolytic potential4 measurements is controversial. This controversy may be attributed in part to a lack of definite knowledge5 of the actual nature of the initial films formed in corrosion experiments. In our own corrosion work on copper and 70-30 brass this lack became apparent and necessitated an examination of surface films by X-ray and electron diffraction methods. The present paper is but an introduction to the subject of inhibition and reports the structure of films formed in active corrodents. Experimental Procedure The arsenical coppers and brasses used in this investigation were made by one of the writers* in the plant of the Revere Copper and Brass Co. at Rome, N. Y. Standard commercial melting practice was followed. O.F.H.C. copper and electrolytic zinc were used and all arsenic additions were made by additions of a master copper alloy. The final analyses are given in Table I. Likewise, the extrusion, cold-rolling, and intermediate anneals employed followed standard usage. Final heat-treatments were given to all materials to produce a similar grain size (0.035 to 0.045 mm. for brass and 0.015 to 0.025 for copper) for the alloys containing various percentages of arsenic. Samples 1/2 by M by 1/4 in. were cut from sheet material resurfaced and finished with 0000 metal-lographic papers. The surfaces were all degreased in alcohol and benzine before immersion. After immersion in the corrodent, they were washed gently in tap water, dipped first in alcohol and then in pure benzine and allowed to dry in the diffraction apparatus. The reflection electron diffraction apparatus used has been described by Burwell and Wu1ff.6 Fig. I is typical of the photo-grams obtained. The X-ray apparatus was

Jan 1, 1941

By L. K. Welch, C.W. Macgregor

The past 20 years has seen a revolutionary change in the testing of materials at elevated temperatures. This has largely been brought about by the practical importance of the creep problem in the design of equipment for operation at high temperatures. The short-time tension test carried out at elevated temperatures has consequently assumed in many cases only a secondary role compared with the longtime creep test. In many problems, however, a knowledge of the short-time high-temperature properties of a metal is essential. To mention a few cases in which this is so, we might include all hot-forming operations such as rolling, forging, etc., the welding problem if residual stresses are to be computed, the development of new alloys for high-temperature service where, in the initial stages, time does not permit of long duration creep tests, and others. Usually a knowledge of the short-time properties is desired, if only to serve as a background against which to compare creep behavior. In conducting short-time high-temperature tests, it has been almost the universal practice to determine stresses based on the original area and strains referred to the original gauge length which is usually chosen as 2 in. It has been pointed out1,2 that one of the reasons that the true significance of certain tensile properties is not understood, which perhaps curtails their usefulness, especially when the material is applied under conditions differing considerably from the test conditions, is that true physical stresses and strains are not determined. It is essential to have a knowledge of true stresses and strains in order to correlate the values present in the tension test with those existing, for example, in hot metal-forming operations and in the general problem of the yielding and failure of metals under combined stress conditions. Stress and strain values based on the original dimensions of the test piece do not exist physically except in the early stages of the test. Since at the present time there is very little information in the literature on true stress-strain relations in the short-time high-temperature tension test it is proposed in the following pages to describe a

Jan 1, 1943

By L. K. Welch, C. W. MacGregor

The past 20 years has seen a revolutionary change in the testing of materials at elevated temperatures. This has largely been brought about by the practical importance of the creep problem in the design of equipment for operation at high temperatures. The short-time tension test carried out at elevated temperatures has consequently assumed in many cases only a secondary role compared with the longtime creep test. In many problems, however, a knowledge of the short-time high-temperature properties of a metal is essential. To mention a few cases in which this is so, we might include all hot-forming operations such as rolling, forging, etc., the welding problem if residual stresses are to be computed, the development of new alloys for high-temperature service where, in the initial stages, time does not permit of long duration creep tests, and others. Usually a knowledge of the short-time properties is desired, if only to serve as a background against which to compare creep behavior. In conducting short-time high-temperature tests, it has been almost the universal practice to determine stresses based on the original area and strains referred to the original gauge length which is usually chosen as 2 in. It has been pointed out1,2 that one of the reasons that the true significance of certain tensile properties is not understood, which perhaps curtails their usefulness, especially when the material is applied under conditions differing considerably from the test conditions, is that true physical stresses and strains are not determined. It is essential to have a knowledge of true stresses and strains in order to correlate the values present in the tension test with those existing, for example, in hot metal-forming operations and in the general problem of the yielding and failure of metals under combined stress conditions. Stress and strain values based on the original dimensions of the test piece do not exist physically except in the early stages of the test. Since at the present time there is very little information in the literature on true stress-strain relations in the short-time high-temperature tension test it is proposed in the following pages to describe a

Jan 1, 1943

By L. E. Welch, C. W. MacGregor

THE past 20 years has seen a revolutionary change in the testing of materials at elevated temperatures. This has largely been brought about by the practical importance of the creep problem in the design of equipment for operation at high temperatures. The short-time tension test carried out at elevated temperatures has consequently assumed in many cases only a secondary role compared to the long-time creep test. In many problems, however, a knowledge of the short-time high-temperature properties of a metal is essential. To mention a few cases in which this is so, we might include all hot-forming operations such as rolling,' forging, etc., the welding problem if residual stresses are to be computed, the development of new alloys for high-temperature service where, in the initial stages, time does not permit of long duration creep tests, and others. Usually a knowledge of the short-time properties is desired, if only to serve as a background against which to compare creep behavior. In conducting short-time high-temperature tests, it has been almost the universal practice to determine stresses based on the original area and strains referred to the original gauge length which is usually chosen as 2 in. It has. been pointed out 1,2 that one of the reasons that the true significance of certain tensile properties is not understood, which perhaps curtails their usefulness, especially when the material is applied [ ] under conditions differing considerably from the test conditions, is that true physical stresses and strains are not determined. It is essential to have a knowledge of true stresses, and strains in order to correlate the values present in the tension test with those existing, for example, in hot metal-forming operations and in the general problem of the yielding and failure of metals under combined stress conditions. Stress and strain values based on the original dimensions of the test piece do not exist physically except in the early stages of the test. Since at the present time there is very little information in the literature on true stress-strain relations in the short-time high-temperature tension test it is proposed in the following pages to describe a

Jan 1, 1942

By T. N. Rhodin

There can be two types of films on solids, those which are stable in mono-layers and those which tend to aggregate into three dimensional structures. A great number of metal films formed by condensation onto a solid base are unstable in the sense that they will aggregate into crystals providing the atoms possess sufficient surface mobility. The crystalline structure of the film is strongly influenced by the base in many systems and, in some cases, a single orientation prevails when the force fields around the atoms in the supporting crystal are sufficiently strong.' Relatively little is available in the literature about the nature of these forces and the role they play in promoting a preferred orientation of the atoms arriving at the substrate surface. An understanding of their periodicity and magnitude relative to the surface forces characteristic of the film itself should provide insight into the critical dependence of film orientation on the nature and temperature of the substrate. In addition, this effect may be very useful in preparing samples for surface studies. The study of the physical and chemical characteristics of pure metal surfaces has been severely handicapped by the presence of strongly adherent foreign films. Furthermore, the randomness of the surface orientation has obscured interpretation of experimental results. Evaporation of metals in high vacuum onto carefully selected substrates under ideal conditions for preferred orientation appears suited to the preparation of flat, oxide-free, oriented films for surface reaction studies. Many factors influence their structure and some understanding of the mechanism of their formation is a necessary prerequisite for obtaining satisfactory surfaces for study. The dominant factors in defining film structure are film thickness and growth rate and the nature, condition, and temperature of the substrate. GENERAL ASSEMBLY The system was enclosed in an 18 in. bell jar which rested on an L-shaped neoprene gasket on a ground steel plate as indicated in Fig 1. Rapid evacuation of the system to 10-6 mm mercury was facilitated by a 4 in. manifold, 2 in. packless valve, and an extra large diffusion pump. Suitable arrangement of valves on a secondary manifold readily permitted introduction of purified gases

Jan 1, 1950

By W. A. Ver Wiebe, E. G. Dahlgren

The year 1937 must be considered the most eventful one ever experienced in the development of oil and gas activity. Out of a total of 57 new pools discovered, 18 are apportioned to eastern Kansas and 39 to western Kansas. (For statistical purposes Kansas is divided along the meridian that separates ranges 3 E. and 4 E.) In addition to numerous longdistance extensions of the large Hugoton gas field of southwestern Kansas, two other gas pools were discovered in the area lying west of range 3 E. The 37 new oil pools in that area are to be found in 13 different counties, among which Rice heads the list with a total of seven oil pools and one gas pool. Ellis and Barton Counties both added six new oil pools, while Russell County follows in fourth place with four. Among eastern counties Butler heads the list with four new pools. Cowley arid Chautauqua each accounted for three new discoveries. The number of wells necessary to accomplish this result totals 2657, of which 1915 are oil wells and 128 gas wells. The initial production of the oil wells amounted to 2½ million barrels. Although most of the wells were drilled in proven territory, there was a good deal of wildcatting. The fact that 614 dry holes were completed emphasizes the ever-present risk attendant upon the efforts of pioneers. Some of the more venturesome spirits reached out to the counties farthest west in the state. An indication of the feverish excitement reached at times is recorded in the fact that no less than 600 drilling operations were in progress during one week in May, or the fact that over 100 new locations were staked during the second week in July. During one week in May, 65 successful oil wells were completed for an initial production of 68,000 barrels. Many drilling obligations came due during the year, and this perhaps accounts for the fact that one company had as many as 59 active operations at one time during September. Another evidence of great interest in oil possibilities in Kansas is furnished by the record of sales of oil properties, which in one case reached the high figure of about $3000 per acre.

Jan 1, 1938

By T. Egleston

The necessity of using a refractory material capable of much greater resistance to chemical action and having a far higher melting-point than those which contain silica, which melt and sweat off in the furnace even when not exposed to bases forming with silica more or less fusible compounds, has led to a careful practical study of all those materials which contain very refractory bases. The results of these researches, extending over several years, and made on a very large scale in many of the largest works in Europe, are of the highest interest, not only considered as a step in the progress of the study of the materials themselves, but in the application of refractory materials to metallurgical uses in general. The result of the experience of the last seven years with these basic materials, as in general with all such substanccs, is that natural products cannot be used as such. They are either too uncertain in their quality, contain substances which may in certain cases be very injurious, or, when in a condition in which they might be used, are so rare as to become practically unavailable for employment on a large scale. The materials that may he used are therefore not only limited in number. but they must be prepared artificially. When the use of basic artificial material is further extended, no doubt the number of these substances will not only be greatly increased, but the methods of preparation will be both perfected and cheapened to such an extent as to permit their application in processes for which they have hitherto proved too expensive. The quantity of refractory materials required for making ingots will he from 130 to 150 Ibs. per ton, or between 6 and 8 per cent. of the metal produced. In an establishment producing 2000 to 3000 tons of steel per week, considerable space is required to handle the basic materials properly. It is proposed in this paper to briefly discuss these basic materials and their application in the only two metallurgical processes where they have as yet been applied. These are the basic Bessemer and the basic open-hearth process, known as the Thomas-Gilchrist processes.

Jan 1, 1886

By T. Johnston, B. Cox

The results of oxidation and corrosion experiments on niobium in oxygen and steam at temperatures of 350° to 650°C, and in dilute sulphate solutions at 300°C are presented. The oxidation of niobium in oxygen can be explained in terms of a pre-transition period, which obeys an approximately parabolic rate law, and a post-transition period in which a more rapid linear rate is partially stifled by restriction of the gas flow due to the gvowth of the porous outer film. Due to changes in the porosity of the outer layers the restriction presented by the porous outel. film attains a limiting value. Subsequent oxidation obeys a linear rate law and shows an almost linear dependence of the rate on gas pressure. liltimately a second failure of the protective film may take place leading to a further acceleration in the oxidation rate. In water vapor the oxidation of niobium follows a parabolic rate law and does not show a transition to linear kinetics. The higher oxide, Nba05, was usually absent from the NbO/NbO2 film which was formed. The addition of a small partial pressure of oxygen to the water vapo3, resulted in accelerated oxidation according to the normal kinetics for oxidation in oxygen. The oxygen reacted preferentially with the niobium, and the protective oxide film was reformed when all the oxygen had been consumed. This behavior supports the theory that nucleation of Nb205 on the surface of the protective NbO/NbO2 film is the cause of the accelerated oxidation. After oxidation in steam at high-pressure Nb2Os was found in the protective film. The mode of formation of Nb2O5 under these conditions did not produce a change in kinetics, but was thought to explain the comparatively large dependence on pressure of the oxidation rate. The kinetics of oxidation in oxygenated aqueous solutions at 300°C were similar to those for oxidation in oxygen. A penetrating attack on niobium sheet may be related to the second breakaway observed by some investigators of oxidation in oxygen.

Jan 1, 1963

By Benjamin Gi ldersleeve

Uniquely colored, thin-bedded quartzite is quarried between Crossville and Crab Orchard in Cumberland County, Tenn. It is produced in all sizes up to the limits of transportation from beds usually ranging in thickness from less than 1/2 in. to 6 in. The stone is very resistant to wear and weathering and is marketed throughout the country for many different purposes in exterior and interior construction. The annual production exceeds 36,000 tons, valued at nearly $1,000,000.

Jan 1, 1950

By A. T. Robinson, J. E. Dorn

The electrical resistivities of aluminum alloys containing CU, Ge, Zn, Ag, Cd, and Mg were found to increase linearly with the atomic percentage of the solute atoms. Application of Linde's rule to these data suggests that each aluminum atom contributes 2.5 electrons to the metallic bond. ALTHOUGH aluminum invariably exhibits a Jt\. valence of three in ionic solids, it does not follow necessarily that its valence in the metallic state is also three. As a matter of record, many properties suggest that the number of bonding electrons in metallic aluminum is less than three. For example, as shown in Fig. 1, the atomic radii1 of the metallic elements in the solid state decrease with increasing atomic number at the beginning of any one period. The atomic radius of aluminum, however, is greater than that which would result from a regular decrease in atomic radius with increasing atomic number, suggesting that the number of bonding electrons in aluminum is somewhat less than three. Correlated with the anomalously large atomic radius of aluminum is its abnormally low melting temperature. As the atomic numbers increase in any one period, the melting temperatures of the metallic elements increase.' As shown in Fig. 2, however, the melting temperature of aluminum (13) is only slightly greater than that of magnesium (12). Again the number of bonding electrons in metallic aluminum appears to be nearer two than the expected value of three. In addition Ageev and Ageeva3 alculated the electron density distribution in the aluminum lattice. A comparison of such electron density curves for various assumed valence states of aluminum with experimentally determined curves suggests that the actual number of bonding electrons in metallic aluminum is between two and three. Hume-Rothery and Raynor', " have suggested that the above-mentioned abnormalities are associated with the overlapping of the Brillouin zones of metallic aluminum when it is in the usual face-centered cubic structure. The importance of the number of bonding electrons in metals has been extended recently into the field of mechanical properties. While formerly it was thought that the plastic properties of alpha solid solutions were primarily dependent upon the lattice strain induced in the solvent by the solute, it is now known that the difference in the number of bonding electrons of the solute and solvent also has its influence on the plastic properties."1' In order to achieve a satisfactory correlation of the effect of alloying elements on the plastic properties of aluminum alloys,"'T however, it was necessary to assume that the number of bonding electrons contributed by aluminum was about two rather than the expected value of three. It appeared to be desirable, therefore, to seek other criteria for evaluating the number of bonding electrons contributed by aluminum to its alpha solid solutions, especially in view of the practical as well as the theoretical importance of the effect of valency on the plastic properties. Norbury' was perhaps the first to illustrate that the increase in resistance of alpha solid solutions is associated with the differences in valence of the solute and solvent metals. In a series of illuminating investigations Linden-'' has shown that the electrical

Jan 1, 1952

By W. Seymour

Uranium was cold rolled to a reduction in thickness of 90 pct and the preferred orientation of the grains was determined from X-ray intensity data. Complete pole figures for a large number of atom planes were plotted, and the preferred orientation was found to be duplex (102) [0101 + (012) [021]. These preferred orientations are compared with those reported for many of the hexagonal-close-packed metals. THE preferred orientation of a highly reduced cold-rolled uranium strip was determined in order to obtain additional experimental data which would be useful in further understanding the deformation mechanisms of uranium. The preferred orientations reported herein are not in agreement with those theoretically predicted by Calnan and Clews' for cold-rolled uranium sheets, and differ somewhat from those reported from experiments by Fisher, and Burke and Turkalo. Such variations might be accounted for by differences in the fabrication temperature and the reductions. Experimental Procedure The uranium used in this investigation had been hot rolled to 0.060 in. at 575°C from 0.393 in., and from a 0.060 to 0.020 in. thick sheet at 275°C. From this point the sheet was cold reduced 90 pct to 0.002 in. at room temperature. Three specimens were used to obtain complete pole-figure data. The first was a 1/2 in. square section illuminated by the X-ray beam on the rolling surface. The other two were l/2 in. square longitudinal and transverse sections each made as follows: Approximately 200 1/2 in. square sections of the foil were piled one on top of the other, so that the rolling direction for each piece was kept coincident. A 1/2 in. square by 1/8 in. thick steel section was placed on the top and bottom of a pile and the entire assembly was then bolted tightly together through a 1/8 in. diam hole drilled down through the center. Each pile was then surface-ground from the two proper sides to sections 1/2 in. square by 3/16 in. thick. These specimens were then polished flat and electro-polished to remove 0.005 in. of the surfaces to be examined. It can be shown that uranium is so opaque to a Cu Ka X-ray beam that only a small percentage would be transmitted by one micron of uranium. Therefore, a method of measuring the X-ray intensities diffracted from specimen surfaces was used. The specimens were mounted in a modified Schulz reflection holder' which automatically changed the position of the specimen at a constant rate. The holder, in turn, was mounted on a General Electric XRD-3 Spectro-Goniometer and an automatic record made of the diffracted X-ray intensity vs specimen position. While a specimen moved automatically through 10" inclination, at a rate of l° per min, it simultaneously rotated 360" about a normal to the illuminated surface. (The inclination and rotation angles are referred to as F and a, respectively.) The data were then plotted along the resulting spiral path on a stereographic projection, Fig. 1. Because of defocusing effects on the diffracted beam which occur when diffracting surfaces are in-

Jan 1, 1955

By Jens P. Nielsen, W. H. Justice

This paper describes an improved acidizing technique which has been applied in acidizing gas wells in the La Gloria Field. Wells acidized in this manner exhibited a much greater increase in deliverahility than wells acidized in the conventional manner. The acid is injected into the well in small slugs separated by a small volume of high pressure gas. The acid and gas are displaced from the tuhing by high pressure gas to reduce the hydrostatic head on the well when the acid is recovered from the well. The well is opened for production as soon as the acid and gas are displaced. This procedure permits a very rapid recovery of the acid which results in large increases in the deliverability of the gas wells. It has been found advantageous in the acidization of gas injection wells to inject the high pressure gas directly after the acid without backflowing the acid out of the well. This practice has made it possible to inject the gas in the injection wells of this field with a much lower pressure differential. This reduces the horsepower required to inject the gas and also decrease:, the number of injection wells required per reservoir. INTRODUCTION The results obtained by acidizing gas wells ill the La Gloria Field have varied considerably in the past. For this reason. a planned study of the acidizing procedure was undertaken in order to obtain more consistent results. The Frio Sands of the La Gloria Field are rather permeable and it was not necessary to acidize many of the wells when they were originally completed. At the completion of an eight-year cycling program in several of the gas reservoirs, it became necessary to recomplete many wells in other reservoirs. It was found that the opan Flow potential of the wells recompleted in different sands was not as large as wells that were originally completted in that reservoir. A study of the drilling records of several of these wells indicated that the sands had originally been subjected to considerable hydrostatic drilling fluid overload while the well was being drilled to the deeper sands of the field. It is indicated that during this eight-year period, the drilling mud and water that were lost into the formation when the well was being drilled had formed a relatively impermeable Eone around the well bore. This impermeable zone around the well bore made it very difficult to obtain high deliverability wells when the original wells are recompleted in other zones. Muskat' has shown that in uniformly permeable and porous formations a zone of partial plugging one ft in radius around the well would drastically decrease the productivity of the well. The analysis for this problem shows that the production capacity of a well is very sensitive to the value of the permeability of the zone immediately surrounding the well bore. This is to be expected in view of the highly localized character of the pressure drop in a radial flow system about the well center. The reduction of the deliverability is not proportional to the thickness of the mud-affected zone as the major portion of the reduction in deliverahility IS caused hy the

Jan 1, 1952

By Y. Shimomura, M. Serizawa, Y. Takahashi, K. Miyagawa

The "semi-pellet" sintering method developed and currently being used at the Fuji Iron & Steel's Hirohata Works is discusssd. It is shown that the method makes fine-sized material easily sinterable and increases sinter production. The operation can be incorporated readily into conventional sintering plants. Sintering plant raw materials currently being used in the Hirohata Works consist of 40 pct pyrite cinder, 40 pct fines resulting from crushing and screening of imported ores, and 20 pct others, such as mill scale and iron sands. Pyrite cinder, a major component in the sinter feed, has been getting finer since 1952, due to the increased grinding required for the improvement of the results in the iron sulfide flotation and to the adoption of FluoSolid roasters in sul-furic acid plants; some fines pass 100-mesh sieve almost completely. Increased use of the fine-sized pyrite cinders in the sinter raw mix resulted in such difficulties as decreased bed permeability, uneven firing conditions, and low yield. In an attempt to study the cause and to find a remedy for this problem, a series of experiments were made, using an 80-kg experimental sintering pan. As a result it was established that, by rolling the fine-sized pyrite cinders into small balls of 10 to 3 mm diam (hereafter called semi-pellets) and mixing them into the sinter raw mix, the bed permeability was improved, the sintering time shortened, and the yield and production rate increased. It is proposed that this new method be called the semi-pellet sintem'ng. In recent years the pelletizing process has taken the spotlight in the agglomeration field for treating fine-sized ores here in Japan as well as in the U.S. and Europe. This process produces pellets suitable for the blast furnace charge as such, and consists of three major operations: fine grinding, balling, and firing. With regard to the firing technique, some problems still appear unsolved. In the semi-pellet sintering, however, several ad- vantages can be claimed: the balling operation is relatively simple because only small-sized balls are shown to be acceptable and the operation can be readily incorporated into the conventional sintering plant, since only balling, not grinding or firing, equipment is needed. Basic test work on the process was initiated in 1954 and favorable results were obtained. Accordingly a pilot plant was built in 1955 and the test work was continued. The semi-pellets thus prepared in the pilot plant were tested further by USing them in the actual sintering pan and their beneficial effects ascertained. In late 1956 a drum-type balling machine (2.4X4 m) was installed and it went into operation in April 1957 in conjunction with the Greenawalt sintering plant (8 pans having dimensions of 7.2 m in length, 3 m in width, and 0.3 m in depth). In October 1958 a cone-type pelletizer, with a 2.2 m diam, and later a disk-type pelletizer were further added in the plant. In the DL sintering plant (2000 tpd), newly built in July, 1960, four disk-type pelletizers (3.2 m diam, 10 tph capacity) were installed. By mixing the semi-pellets thus prepared with the feed, the sintering operation was found to be greatly improved. The results of the basic test work, and the equipment and operation of the semi-pellet sintering operation at the Hirohata Works will be described. ON THE SINTERING CHARACTERISTICS OF FINE SIZED PYRITE CINDERS To ascertain the effect of addition of fine-sized pyrite cinders on the sintering characteristics, a series of measurements on bed permeability was carried out by varying the size distribution of pyrite cinders. The composition of the raw mix used in the tests was fixed at 50 pct pyrite cinder, 20 pct Larap magnetite fines, 30 pct sinter return, and 5 pct coke; only the size distribution of the pyrite cinder was varied. Also the moisture content was changed at each size distribution. The results are given in Fig. 1. For all pyrite cinders tested the bed

Jan 1, 1961

By M. C. Flemings, G. E. Nereo

General expressions are given to describe macro-segregation in castings and ingots which results from mass flow of solute-rich liquid to feed solidification and thermal contractions. Analytical solutions are given for solidification with planar isotherms (unidirectional and bidirectional heat flow). These solutions describe inverse segregation and centerline segregation. Numerical examples are given for A1-4.5 pct Cu alloy. In 1540, Vannoccio Biringuccio published one of the first references to macrosegregation, describing the problem of exudation and inverse segregation in the manufacture of bronze gun barrels.' Since then, a great many studies of macrosegregation have been reported. Recent work of particular engineering interest includes that of Marburg 2 and others:" on centerline segregation and other types of segregation in large steel ingots, and work of Adams,5 Scheil, 6 and Kirkaldy and youdelis7 on inverse segregation in nonferrous ingots. In most studies on this subject, the various types of macrosegregation have been treated as separate phenomena. For example, quite different mechanisms have been proposed for formation of centerline segregation, negative cone of segregation, inverse segregation, banding, and so forth. In this, and in several papers to follow, it is proposed that these as well as other types of macrosegregation result from the same basic mechanism and can be quantitatively described by the same basic equation. It has often been suggested that some types of segregation (such as centerline segregation and banding) occur as a result of buildup of solute at the tips of growing dendrites.2-4 ,8-10 As example, banding can be induced in centrifugal castings by mechanical vibration, and Northcott 10 suggests this might be due to the influence of the vibration on the boundary layer at the dendrite tips of the growing dendrites. However, in view of the extremely small boundary layer known to exist at the tips of the dendrites,11,12 any interpretation of macrosegregation based on this boundary layer is clearly incorrect. Note that experiment has shown that significant buildup of solute does not occur at dendrite tips in ingot solidification, but even if such buildup occurred the thickness of the enriched zone would only be the order of D/U where D is liquid diffusion coefficient and U is dendrite tip velocity. For usual casting or ingot solidification this solute-enriched layer is 10"3 cm, far too small to account, for example, for centerline segregation.11'12 It has also been suggested that convection in the bulk liquid (ahead of the advancing dendrites) might cause segregation by sweeping away the solute-rich boundary layer in front of the dendrites.3 However, since there is no significant boundary layer, this explanation must be incorrect. The convection might directly cause segregation by penetrating between the dendrite arms, and presumably in a rimming steel ingot it is sufficiently vigorous to cause some segregation in this way. Centerline segregation, however, cannot be interpreted as resulting from this convection since a sharply segregated zone is usually found near the centerline, with the bulk of the ingot being nearly of nominal composition. If convection in the bulk liquid were the direct cause, a gradual change in ingot composition over the entire cross section would be expected. It is known that sudden changes in convection of the bulk liquid during solidification can result in banding,14 but it is not clear that the banding results directly from the effect of convection on solute distribution. Changes in convection also affect thermal conditions in the liquid-solid region of a solidifying ingot. It will be seen later in this paper, and in a paper to follow, that macrosegregation is strongly influenced by these thermal changes. Recognizing that in some cases of ingot solidification (as in solidification of rimming steels) convection in the bulk liquid may have a direct effect on solute distribution, we neglect it in this paper and in the several to follow. We then derive general expressions describing macrosegregation which results from the mechanism of interdendritic flow of solute-rich liquid

Jan 1, 1968

By William L. Boyd, Eugene L. McCarthy, Laurance S. Reid

Proper control of the moisture content of natural gas is essential to reliable operation of gas transmission and distribution facilities serving northern markets. The moisture content of natural gas is usually determined by dew point measurement at the existing pressure. For any gas of constant moistrire content. the dew Point varies with the pressure. A correlation of the data of several investigators is prezented in graphical form by the authors. These data were correlated by the authors and F. M. Townsend, C. C. Tsao. M. I). Rogers. Jr.. and J. A. Porter. graduate students in chemi(.a1 engineering at the University of Oklahoma. Of articular interest are the hitherto unpublished low temperature data observed by Wickliffe Skinner. Jr., which are included in this correlation. PRESENTATION OF DATA The problem of interpreting water dew points, or saturation temperatures. of natural gas in terms of specific moisture con-tent has increased in importance during the past decade bec.arl.;e of extensive development.; in the transmission and petro-chemical phases of the natural gas industry. Virtually all gas transported to northern and eastern markets must be dehydrated to a low water vapor content to prevent hydrate formation in transmission and distribution lines and resultant interruption.; in gas deliveries. Complete dehydration is required in certain phases of tile petro-chemical industry involving low-temperature operations. It is a well-known fact that the water vapor content of pure hydrocarbon vapors and their mixtures at superatmospheric pressures cannot be predicted with accuracy by assuming validity of the ideal gas laws." Earlier interest in the general problem was concentrated on the water vapor content of pure hydrocarhons and hydrocarbon mixtures in the pressure and temperature ranges common to gas and oil producing reservoirs in order to obtain fundamental data for the improvement of production techniques and the furtherance of reservoir studies. Excellent data are published for pressures ranging from atmospheric to 10,000 psig and for temperatures ranging from 100° to 460° F4,9,10,11 and are found to be in close agreement. However, experimental data at high pressures and temperatures below 100°F are comparatively limited in scope. Experimental data in the lower temperature range have been reported by Laulhere and Briscoe.8 Deaton, et al,2,3 Hammerscllmidt,5,6 and wade," In general, the pressures employed in these investigations ranged from atmospheric to 1.000 psig while temperatures ranged from 32° to 120°F; i.e., the usual conditions encountered in gas transmission line operations, Additional data were reported by Russell, et al,12 at pressures as high as 2.000 psig and covering a rather narrow atmospheric temperature range. In 1947, Hammerschmidt published a correlation of all available data,' in which the water vapor content of gases at saturation. under high pressure and low temperature. was predicted by extrapolation. In 1948, Wickliffe Skinner. Jr.. presented data on the moisture content of a low nitrogen content gas at low temperature and at pressures ranging upward to 1.500 psia.1-3 Comparison of Skinner's experimental data with the extrapolated data of Hammerscllmidt revealed an appreciable variation in the lower temperature range. emphasizing the need for a new correlation which would rely on Skinner's data at lower temperatures. Careful scrutiny of available data suggested that presence of an appreciable quantity of nitrogen in a gas mixture may affect its saturated moisture content so that data obtained from gases with more than three per cent nitrogen were not used in this correlation. CORRELATION OF DATA Data employed in this correlation are presented in Table I. The data of Dodson and Standing.4 McKetta and Katz,9 and Olds, Sage and Lacey10 were compared and found to be in close agreement so that the data of Olds. et al, re-plotted in a more convenient form by the Humble Oil and Refining Co.,' were used for temperatures of 100°F and above. Skinner's data were used for temperatures below 40°F. Between these intermediate temperature limits, the data of Hammerschmidt.7 Wade" and extrapolated data of Olds. et al.1 were tabulated

Jan 1, 1950

By A. E. Back, S. F. Ravitz

When manganese ores are leached with sulphur dioxide, a large part of any zinc in the ore usually is extracted with the manganese.1 In the dithionate process,2,3 in which the manganese ore is leached with dilute sulphur dioxide gas and the manganese is subsequently precipitated by adding lime to the pregnant solution, the zinc is precipitated with the manganese. These facts suggested the possibility of applying the dithionate process to the recovery of zinc from oxidized ores or calcined sulphide concentrates. Accordingly, an investigation was begun, and preliminary tests were made on several ores and concentrates. The results were encouraging, but the need to devote available funds and personnel to other projects made it necessary to drop the work before the various factors involved in the process could be studied in detail. A brief mention of the process,4 however, elicited a number of inquiries, so that it appeared desirable to report the results of the preliminary work. The dithionate process as applied to zinc may be summarized briefly as follows: The ore or calcined concentrate is leached with dilute SO2 gas to dissolve the zinc, largely as zinc sulphate, in accordance with the following equation in which [ZnO] represents the "oxide zinc" in the ore or calcine: [ZnO] + SO2(g) + 1/2 O2 = Zn++SO4— [1] If, in the leaching step, the ore or calcine is suspended in calcium dithionate solution, the sulphate ion, as it is formed, is precipitated immediately as calcium sulphate, which is subsequently filtered off with the insoluble ore residue: Zn++SO4— + Ca++S2O6— = CaSO4(s) + Zn++S2O6- [2] An alternative procedure is to suspend the ore in water, filter off the insoluble ore residue after leaching, add calcium dithionate to the resulting zinc sulphate solution, and then filter off the calcium sulphate precipitate. In either event the zinc is obtained in the form of a pregnant solution of zinc dithionate, from which it can be precipitated as relatively pure zinc hydroxide by adding milk of lime: Zn++S2O6— + Ca(OH), = Zn(OH)2(s) + Ca++S2O6- [3] The zinc hydroxide precipitate is calcined to form the final zinc oxide product: Zn(OH)2 = ZnO(s) + H2O(g) [4] Theoretically the process is completely cyclic with respect to dithionate ion, the calcium dithionate required for reaction 2 being replaced by that formed in reaction 3. In practice, of course, small amounts of dithionate would be lost in the various filter cakes, depending on the economic washing limits. In the leaching step, however, some of the SO2 is oxidized to dithionale instead of sulphate, accord- ing to the following overall reaction: ZnO + 2SO2(g) + 1/2 O2(g) = Zn++S2O6-, [5] so that the dithionate losses are made up, at least in part. Ores and Concentrates Tested The analyses of the ores and concentrates tested are summarized in Table 1, which also includes the analyses of the calcines produced from the concentrates. The concentrates were roasted in a laboratory muffle furnace at the temperatures indicated until evolution of SO2 could no longer be detected; shallow clay dishes ordinarily were used; but calcines 2a and 2c were prepared in iron dishes, with the result that these two calcines were badly contaminated with iron scale. The "complex" concentrate, sample 1, consisted essentially of sphalerite grains containing inclusions of pyrite and other sulphide minerals too minute to be liberated by grinding within economic limits. In the " marmatitic" concentrate, sample 2, the iron was present largely as marmatite (that is, as iron sulphide in solid solution in zinc sulphide) rather than as pyrite inclusions. The zinc was present largely as the carbonate in the two "oxidized" ores, samples 3 and 4, and as the silicate in the "willemite" ore, sample 5. Leaching Tests The leaching cell was a 3-liter glass beaker placed in an electrically heated water bath manually controlled to maintain a temperature of 35°C in the leach slurry. The slurry was agitated by means of a flat paddle-type stirrer

Jan 1, 1950

By L. D. Jaffe, H. C. Mann, E. L. Reed

It has been generally believed that fracture originates at a point and, if the stress is suficient, propagates across the material from this point. Evidence to the contrary is given in Fig 1. This micrograph shows an area close to the fracture of a steel containing The material had been quenched from 1675°F and tempered at 1150°F as a round about 10 in, in diam, and had a static tensile strength of 132,000 psi and a static yield strength of 105,000 psi. The steel was broken in 3000 cycles of reversed bending at a nominal max. fiber stress of 110,000 psi at a speed of 10,000 rpm. It was in the form of a standard R.R. Moore specimen with 45" V-notch, 0.015 in. radius and 0.220 in. diam at base of notch. The fractured edge in Fig 1 is part of the central portion of the specimen which broke during the final sudden fracture. Attention is directed to the short cracks which appear as dark lines within the specimen. Similar cracks were found in another specimen of the material, broken in 1,798,000 cycles at a nominal stress of 40,000 psi. The cracks were found in several areas close to the path of the final sudden fracture. This final fracture appeared microscopically to be wholly brittle and transcrystalline. Closer to the surface of the specimens, near the path of progressive fracture, which presumably advanced gradually during many cycles, there was microscopic evidence of some local deformation, but no microcracks. Neither were microcracks observed in areas distant from the main fracture path. The following explanation is offered: In the sudden fracture of the specimen, a crack propagates along a crystallo-graphic plane, with little or no plastic deformation of the adjacent material, until it reaches a grain boundary or a particle of carbide or inclusion which stops its advance. (The particle or boundary may be outside the plane of polish and not visible in the micrograph.) A stress concentration occurs about the end of the stopped crack. One or more new cracks are likely to start in the zone of this stress concentration. They may lie in the same grain as the first crack or in an adjacent grain. New cracks may occasionally start in a nearby but not adjacent grain whose orientation with respect to the stress leads to more ready fracture than does that of the grain between. Once started, these cracks propagate along crystallographic planes in their grains and the process repeats. This leads to discontinuous, branching chains of microcracks. As the process continues, microcracks probably tend to link up by fracture of intermediate material under the influence of increasing stress concentration. Occasionally, too, there may be a series of nearby grains of similar orientation so that there is a certain continuity of fracture across them. In either case the effective size of a crack is increased, resulting in greater stress concentration at its ends and a greater likelihood of further increase of size of the continuously-fractured region. When one continuous crack crosses the entire specimen, macroscopic fracture has occurred. The fractured edge of the specimen in Fig 1 represents a series of microcracks which became continuous across the entire specimen. The short, dark-appearing cracks in the figure did not become continuous over a large area. The row of microscopic stress concentrations at their ends may link up with those of the "main crack" outside the plane of polish. The above explanation does not imply that microcracks develop at the same rate in all portions of the specimen. They will develop most rapidly where the macroscopic tensile stress and macroscopic stress concentration are greatest. Viewed on a scale large compared to the grains, the fracture would appear to progress continuously across the specimen. Although Fig 1 shows a specimen broken in a fatigue test, it is believed that the microcracks discussed do not depend on the repetitive nature of the stressing used, since they are in the region where "sudden" fracture occurred, presumably in a single stress cycle. The whole process of microcrack propagation outlined above is thought to have occurred during this single cycle. It is believed that discontinuous crack propagation may be universal in brittle transgranular fracture of crystalline solids. Further experiments are under way.

Jan 1, 1950

A. G. Cockbain—The paper by Burlingame, Bitsianes and Joseph is of great interest in extending the work done on high grade sinters, particularly that of Hessle, and the development and application to them of the technique of McBriar, Johnson, Andrews and Davies on ironstone sinters. In this laboratory the work of McBriar et al. has also been continued and extended to cover high grade sinters, and a sectioning technique similar to that used by McBriar et al. was attempted on sinter cakes made in the laboratory sinter unit, using magnetite concentrates (containing 64 pct Fe). In these experiments no attempt was made to flush out the products of combustion with nitrogen before cooling. It was considered that free air penetration would occur on only a limited scale with the size of sinter cake made (14 in. sq x 12 in. deep). Chemical analyses of the zones showed generally similar features of those described by Burlingame et al. and especially the FeO rich region at and just behind the flame front, i.e. zones of ignition and combustion. This seems to indicate that the nitrogen atmosphere does not materially affect the states of oxidation in the sinter cake or at least that special care is not required unless the sinter cake is small. Burlingame et al. consider that FeO present has some significant part to play in the mechanism of sintering. This view does not find favor with the author. The reduction of iron oxides in the presence of red hot coke is a well known phenomenon, whether conducted in an atmosphere of nitrogen or in a crucible in air, and in view of the presence of some carbon in the hot sinter, especially just at the ignition zone, cessation of the progress of the flame front will in no way affect the reduction of iron oxides near hot coke. Even in a nitrogen atmosphere some CO and CO, will be generated by reduction and by continual oxidation and reduction of CO as the transfer agent, the oxidation state of the iron oxides can be lowered quite rupidly so long as free carbon exists with enough heat. Knowing the composition of the gas at the flame front (obtainable by probes), it would be possible to calculate the static oxidation state of Fe2O3/Fe3O2 in equilibrium with it and hence obtain a check on the chemical analyses to see if in fact direct reduction of the Fe2O3/Fe2O1 to FeO has taken place. Have the authors attempted this? It appears to this writer that what is required is some means of reducing rapidly the heat content of the ignition zone and immediately behind, and at the same time insuring no oxidation by the air. In ironstone sinters the difficulty of oxidation state of the iron did not arise on account of the very large slag bulk. However, in high grade sinters knowledge of this, and also the mechanism whereby high oxidation states can be obtained in the final sinter, is of great interest. R. D. Burlingame (author's reply)—The question has been raised as to whether the high FeO content found in high-fuel sinters is due to actual reduction at the advancing flame front or due to unavoidable direct reduction during the quenching period. For such direct reduction to have taken place in the freshly-formed sinter, a considerable amount of solid carbon would have had to escape combustion and be available throughout the hot sinter zone during the quenching period. A simple stoichiometric calculation with the limited data available indicates that a zone of freshly-formed sinter over 2 in. wide must have averaged roughly 2 pct C to accomplish the amount of reduction found. Furthermore, the presence of this amount of carbon would indicate that the fuel in the charge had not burned over a narrow front but over a zone at least 2 in. thick. In contrast to such a condition, the data of the present investigation indicate that the combustion of fuel is confined mainly to a narrow front in which high temperatures and reducing conditions favor. the formation of excess ferrous iron.

Jan 1, 1959

By E. R. Buchanan, R. E. Reed-Hill

Cylindrical magnesium single crystals were deformed in torsion. The axis of torsion was the basal pole. Five crystals were deformed to different strains between 0.08 and 1.03 and then sectioned in order to determine their dislocation densities using the transmission electron microscope. The work hardening rate of all specimens was at least an order of magnitude higher than that normally associated with easy glide in a tension test and comparable to that obserzed in stage B of a tension test. The correspondence between stage B in a tension test and the initial stages of a torsion test is believed to result from the fact that in both cases deformation occurs in a structure containing roughly equivalent densities of the dislocations associated with the three basal slip vectors. THERE are three basic ways of changing the shape of a crystal using slip dislocations. The crystal can be sheared along a slip direction in a slip plane; it can be bent about an axis in the slip plane normal to the slip direction; and, if the slip plane contains multiple slip directions, it can be twisted or rotated about the slip plane normal. Of the three processes, generally known as translational, flexural, and rotational slip, only rotational slip has not been extensively investigated. The object of the present research was to obtain basic information about this phase of crystalline plasticity. This paper is concerned with some aspects of the stress-strain curves obtained by twisting magnesium crystals about their basal poles. Magnesium was selected for four reasons. One, its recovery rate at room temperature is relatively low. Two, single crystals may be easily grown. Three, at room temperature the critical resolved shear stress for basal slip is about two orders of magnitude lower than that for nonbasal slip, so that rotational slip might be expected to occur primarily by basal slip. Finally, relationships between flow stress, shear strain, and dislocation density have been determined for tensile deformation of magnesium crystals,' thereby providing a basis of comparison for the torsional results. EXPERIMENTAL PROCEDURES Crystals were grown from 0.5 in. diam extruded sublimed magnesium rod furnished by the Dow Chemical Co. who reported that it contained in weight percent less than 0.0003 Al, 0.01 Ca, 0.01 Cu, 0.0012 Fe, 0.001 Mn, 0.0005 Ni, 0.003 Pb, 0.001 Si, 0.01 Sn, and 0.02 Zn, with the balance magnesium. All crystals were grown in a dried argon atmosphere using Jill-son's2 modified Bridgman technique. Two different methods were used to obtain crystals with the basal plane normal to the specimen axis. These included direct growth from seeds of the proper orientation, and spark machining (trepanning) of 0.5 in. diam cylinders from larger (1.5 in. diam) randomly grown crystals. The crystals thus produced were polished in a 20 pct HC1 water solution and then etched in a 1 pct HC1 water solution to develop etch pits lying in rows parallel to the basal plane trace. The crystals were then revolved about their axes on the stage of a low-powered microscope. Torsion specimens were prepared only from those crystals whose axes were normal to the rows of etch pits. It is estimated that this simple orientation method was accurate to about 51 deg. 1.625 in. long cylinders were next cut from these selected crystals and then acid machined in a 20 pct HC1 water solution into torsion specimens with a 1 in. long by 0.30 in. diam reduced gage section. Following this, they were annealed in air at 400°C and furnace cooled to room temperature. The specimens were given a final polish in a 10 pct HC1 water solution, rinsed in ethanol, dried, and cemented into brass grips with an epoxy resin. In addition to the torsion specimens, several tensile specimens with their basal planes at 45 deg to the stress axis were also prepared with similar dimensions except that the gage sections were increased to 4 in. in length. The torsion specimens were tested in the apparatus

Jan 1, 1970

By R. J. Quigg, G. S. Doble

Commercial stress -relieved TD Nickel bar was shown to retain room- and elevated-temperature tensile strength after exposure up to 2501°F. Cold swaging increased both room -temperature and 2000°F tensile strength. After annealing at 2500°F the strengthening due to swaging was retained at 2000°F hilt eliminated at room temperature. Annealing produced changes in hardness and X-ray half peak width indicating the presence of recovery processes as 1071° as 1000°F but no recrystallization of swaged material was noted at any temperature. In contrast to swaging, rolling induced a recrystal-lized structure after annealing. The tensile strength of this recrystallized structure was comparable to the cold-worked condition. High-temperature tensile properties of as -received bar were highly anisotropic with the transverse tensile strength being one fifth the longitudinal value. The aniso-/ropy is affected by working direction and may he partially reversed by changing the direction of metal flow. The divergence in tensile strength, beginning above 550°F or- approximate one third the absolute melting point, is strain-rate dependent. T D Nickel is a commercial dispersion-hardened alloy containing 2 vol pct thoria. The dispersion, consisting of spherical particles 0.030 to 0.050 in diameter with an interparticle spacing of less than 1 is reported to maintain stable properties up to 2400°F.1 This stability of second phase results in maintenance of elevated-temperature strength at higher temperatures and longer times than normal nickel-base superalloys.2 The purpose of this paper is to describe the effect of various mechanical working operations on the strength and microstructural stability of TD Nickel bar. MATERIAL AND PROCEDURES All material used in this study was commercial TD Nickel bar. This material is produced by a chemical process which results in a nickel powder containing a dispersion of thoria particles. The powder is then pressed, sintered, extruded, and subsequently worked to bar stock. Three starting materials from three separate lots were used: as-extruded bar. 1-in.-diam stress-relieved bar, and 1/2-in.-diam stress-relieved bar. Since TD Nickel bar stock is cold-worked without a recrystalliza-tion anneal, the accumulated deformation or degree of cold work in these materials increases as the bar diameter decreases. Some of the 1/2-in.-diam bar was swaged to 1/4 in. diameter at room temperature in order to produce an as-worked condition for comparison with the stress-relieved stock. Tensile testing was performed on an Instron Tensile Tester at a constant crosshead speed of 0.020 in. per min. The 0.2 pct offset yield strength was measured from the load-crosshead movement plot. Specimen gage dimensions were 0.080 in. in diameter by 0.40 in. in length, producing a strain rate of approximately 0.050 min-1. Specimens were tested in air and heated within a resistance-wound furnace controlled to ±5°F. A 15-min soak at temperature was employed before testing. Samples were heat-treated in air and specimens machined after exposure with sufficient material removed to eliminate any surface contamination. X-ray line breadth was determined from a diffractometer scan of a transverse face of a bar using copper K, radiation. Metallographic preparation utilized standard mechanical polishing with Carapella's etch. Specimens for electron microscopy were electropolished in a 1:7 sulfuric/methaol solution and chromium-shadowed collodion replicas prepared. RESULTS AND DISCUSSION I) Effect of Elevated-Temperature Exposure on the properties of TD Nickel. The effect of various elevated-temperature exposures on the room-temperature tensile strength of TD Nickel is shown in Table I. In the unexposed condition the tensile strength, reduction in area, and hardness all increase with increasing accumulated deformation while the elongation decreases. After exposure at 2500°F the strength of all three materials decreases to about 65,000 psi and the elongations increase slightly. The apparent increase in strength of the 1-in. bar after a 2000°F treatment is probably experimental scatter. These results indicate that the room-temperature strengthening due to additional deformation is annealed out upon elevated-temperature exposure. In contrast to the room-temperature data, the 2000°F tensile strengths increase in order of increasing deformation even after exposure. Although some loss of strength occurs after exposure, much of the effect of working is still maintained at 2000°F. The room-temperature hardness after various

Jan 1, 1965