Search Documents

By J. H. Keeler

QUESTIONS raised during earlier investigations of the preferred orientation in titanium1 and zirco-nium sheet led to the examination of the rolling and annealing textures of beryllium and hafnium sheet. Since the c/a ratios are 1.568 and 1.584, less than that of ideal close packing, 1.633, it would be expected that the preferred orientations would be similar to those exhibited by zirconium and titanium. This was found to be true. However, in several regards the orientations observed for beryllium differed from those reported by Smigels-kas and Barrett4 and so are given here. The okientations for hafnium are presented since only the cold-rolling texture has been reported in the unclassified literature. The pole figures were determined by transmission using an X-ray spectrogoniometer with copper Ka radiation and the automatic pole-figure recorder designed by Geisler described previously.6 The intensity units in the pole figures in this case are only arbitrary since calibration against a random sample of the same material was not considered necessary for the original purpose of the examination. The beryllium sheet, cold-rolled from 0.036 in. to 0.006 in., a reduction of about 84 pct, exhibited a split texture with the [1010] direction in the rolling direction as shown in Fig. 1. The same specimen annealed in vacuo for 1 hr at 1000°C showed no change in orientation. These textures

Jan 1, 1959

By James P. Roe

Those who deem the subject of this paper an old and superseded one may recall with advantage the words of the great proverb-maker, bidding us to seek the new in the ashes of the old. The manufacture of wrought-iron began with the small hearth built upon an eminence, and relying on the wind for blast. Next came, either the hearth about 12 in. in diameter by 2 ft. in height, blown by a man operating two goat-skins for bellows, or, a hearth of greatly varying diameter and about 10 R. high, depending for its blast upon natural draft. The former appeared in India, the latter in Burmah; and both were in operation until quite recently, though their origin is lost in prehistoric times. The Catalan forge was the evolutionary descendant of the foregoing, and the parent of the Blase-ofen, which in turn led to the high bloomary or " StÜckofen," the father of the blastfurnace, as a producer of cast-iron. The production of cast-iron checked the growth of the direct processes; and led to the introduction of various hearths, such as the Walloon, for low-silicon irons; and the South Wales process, combining the run-out fire with the finery, for higher-silicon irons. Some of these are still in operation in localities possessing the necessary raw materials; and their product is used for purposes requiring wrought-iron of exceptional quality, the supply of which is still smaller than the demand.

Jan 1, 1906

By F. M. Lewis, J.F. Myers

The Tennessee Copper Company's operations are in the Ducktown Basin, in the extreme southeast corner of Tennessee. The ore is of the heavy sulphide type, the predominating sulphides being pyrite, pyr-rhotite, chalcopyrite and sphalerite. The gangue is a micaceous schist, with varying amounts of free quartz. The mining operation develops two classes of ore, each of which is concentrated by the flotation process in separate mills. Table 1 shows a typical analysis of the ore treated in each mill. The London mill was built in 1922, with a capacity of 400 tons per day. This was gradually increased to 600 tons by 1926, to 900 tons in 1928, and to 1350 tons in 1938. Fig. 1 shows the crushing and grinding flowsheet in 1928, when the capacity was 900 tons; Fig. 2, the crushing and grinding flowsheet that was developed by 1938, for the treatment of 1350 tons per day. A comparison of these flowsheets reveals that this increase in tonnage, with a subsequent improved operation, was accomplished with identically the same major equipment. Improving a concentrator's capacity, metallurgical results, and costs as time goes by is a commonplace practice, and is accomplished in various ways, depending upon the local conditions. The reason for presenting the data of how this was accomplished in the mills of the Tennessee Copper Co. is that a fast-running rod mill plays such an interesting role

Jan 1, 1943

By E. P. Barrett

THE high-frequency laboratory induction furnace with a rotating liquid crucible enables research workers to conduct certain investigations heretofore very difficult or impossible to realize because vessels are not obtainable that are capable of resisting the physical conditions or the chemical actions to which they are subjected. Applications for patents covering commercial uses of centrifugal liquid crucibles were filed in the United States in 1919,1 in France in 1925, in the United States and Germany in 1926,2 and in France in 1927.3 In 1928, Schuette and Maier,4 of the Bureau of Mines, reported the construction of a whirling table beneath a high-frequency induction furnace. SHAPE AND SIZE OF CENTRIFUGAL LIQUID CRUCIBLES When a vessel containing a liquid is rotated, the inner surface of the liquid takes the shape f a paraboloid under the simultaneous action of centrifugal force and gravity. The internal dimensions of the paraboloid rotating liquid crucible are governed by the diameter of the container and its speed of rotation. Melted Wood's metal was poured into cylinders 2 ½ in. in diameter, which were rotated at 180, 300, and 468 r.p.m. When the metal was solid, a slurry of plaster of Paris was added, and rotation continued until the plaster had set. Fig. 1, a photograph of sections f the cylinders, shows the effect f speed f rotation of the containers upon the shape f the inner surface f the rotating liquid crucibles.

Jan 1, 1938

By J. F. Myers, F. M. Lewis

The Tennessee Copper Company's operations are in the Ducktown Basin, in the extreme southeast corner of Tennessee. The ore is of the heavy sulphide type, the predominating sulphides being pyrite, pyr-rhotite, chalcopyrite and sphalerite. The gangue is a micaceous schist, with varying amounts of free quartz. The mining operation develops two classes of ore, each of which is concentrated by the flotation process in separate mills. Table 1 shows a typical analysis of the ore treated in each mill. The London mill was built in 1922, with a capacity of 400 tons per day. This was gradually increased to 600 tons by 1926, to 900 tons in 1928, and to 1350 tons in 1938. Fig. 1 shows the crushing and grinding flowsheet in 1928, when the capacity was 900 tons; Fig. 2, the crushing and grinding flowsheet that was developed by 1938, for the treatment of 1350 tons per day. A comparison of these flowsheets reveals that this increase in tonnage, with a subsequent improved operation, was accomplished with identically the same major equipment. Improving a concentrator's capacity, metallurgical results, and costs as time goes by is a commonplace practice, and is accomplished in various ways, depending upon the local conditions. The reason for presenting the data of how this was accomplished in the mills of the Tennessee Copper Co. is that a fast-running rod mill plays such an interesting role

Jan 1, 1943

By E. G. Leonardon

THE first to appreciate and foresee the value of applying electrical measurements to structural studies was Prof. Conrad Schlumberger, Professor of Physics at the School of Mines in Paris. One of his earliest practical undertakings in this line was carried out, in the field, at Fierville-la-Campagne, Normandy, in 1912. His book, published in 1920,1 still stands as an authoritative, fundamental treatise on the use of the electric current in geological studies, in spite of the rapid evolution of geophysics during the last seven years. A remarkable feature of this book is that, even then, it stressed the role of electricity in structural investigations and made public the first successful results obtained therewith. Stratigraphic studies have been pursued continuously by Conrad Schlumberger and his associates since 1912, the only interruption being the World War. The results attained demonstrate the wide possibilities of electrical exploration in structural work. This field of activity is, at the least, as varied and valuable as the search for ore. It is curious that until very recently it has so slightly attracted the attention of geophysicists and geologists on this continent. The purpose of this paper is to present briefly some examples of the practical application of the potential methods to geological studies. These examples are chosen from a number of problems solved in the field by our firm, in the course of its consulting practice. Certain fundamental points are briefly stated before the field operations and interpretations are described.

Jan 1, 1928

By William Blauvelt

Tun technical and engineering problems in the manufacture of coke are today the problems of the byproduct oven. Except in a few special localities, practically no beehive ovens have been built in the United States for the last 5 or 6 years except as renewals of old plants, and during these years the total number of beehive ovens in existence has been steadily falling. On the other hand, the number of byproduct ovens has increased from 4624 in 1911 to a total of about 7660 in operation at the end of 1917; with 2800 building, this makes a total of about 10,460 which will be in operation in 1918, or shortly thereafter. Preliminary Government estimates place the total production of coke for 1917 at 56,600,000 tons, the largest tonnage in the history of the industry. Of this 34,000,000 tons or 60 per cent. was beehive, and 22,-600,000 tons, or 40 per cent. was byproduct coke. Some time in 1918 the production of byproduct coke should pass the beehive output, and when the byproduct ovens now building are completed the total byproduct capacity will be about 40,000,000 tons of coke per. annum, which is over 70 per cent. of the record-breaking total coke production of 1917. The reasons for these changes in the coking industry are familiar to all of us, and need not be discussed here.

Jan 3, 1918

By John C. F. Randolph

This establishment being now in full working order, it has seemed of considerable professional interest to collect together, in a concise form, the various points as to its plan, method of dressing, and equipment. The data contained in this paper have been largely drawn from the able paper of E. Kutscher, constrnoting engineer of the works, contained in the Zeitschrift fur Berg-HÜtten-und Salinenwesen im Preussischen Staate, 1873, supplemented by some personal memoranda made while the works were under construction and by memoranda on the works appearing in various German technical papers from their completion up to date. This is probably the largest dressing works in the world devoted to the beneficiation of argentiferous lead ores, and it is doubtful if any establishment for the concentration of mineral of any description can compare with it in size. As showing the final practice adopted in an old and very conservative mining region, in which the concentration of ores has been a matter of constant practice and experiment for a very long period, these works are of peculiar interest. The fact that the Clausthal ores strongly resemble a very large and abundant class of ores found in the United States has always attracted the attention of American mining engineers and mine owners to the methods employed in dressing and smelting them. The study of their methods of concentration of ores has, however, always been full of difficulty,

Jan 1, 1879

By John C. F. Randolph

(Read at the Amenia Meeting, October, 1877.) Tits establishment being now in full working order, it has seemed of considerable professional interest to collect together, in a concise form, the various points as to its plan, method of dressing, and equipment. The data contained in this paper have been largely drawn from the able paper of E. Kutscher, constructing engineer. of the works, contained in the Zeitschrift fur Berg-Hütten-und Salinenuesen im Preussischen Staate, 1873, supplemented by some personal memoranda made while the works were under construction and by memoranda on the works appearing in various German technical papers from their completion up to date. This is probably the largest dressing works in the world devoted to the beneficiation of argentiferous lead ores, and it is doubtful if any establishment for the concentration of mineral of any description can compare with it in size. As showing the final practice adopted in an old and very conservative mining region, in which the concentration of ores has been a matter of constant practice and experiment for a very long period, these works are of peculiar interest. The fact that the Clausthal ores strongly resemble a very large and abundant class of ores found in the United States has always attracted the attention of American mining engineers and mine owners to the methods employed in dressing and smelting them. The study of their methods of concentration of ores has, however, always been full of difficulty,

Jan 1, 1878

By George W. Neumann

The mines and concentrator of Brunswick Mining and Smelting Corporation are located in the northern part of the province of New Brunswick, approximately 20 miles distant from the City of Bathurst. Discovery of the No. 6 orebody by diamond drilling in 1952 was followed by the finding in March 1953, of the larger and higher- grade No. 12 orebody, approximately six miles to the north of the No. 6 deposit. Original development was financed by St. Joseph Lead Co., and included a small open-pit operation with a 10C ton per day pilot mill at No. 6 orebody, shaft sinking and underground development at No. 1; orebody, and an extensive program of laboratory and pilot plant metallurgical research on No. 12 ore. These operations were suspended in May 1958, and remained in standby condition until June 1961, when the equity of St. Joseph Lead Co. was purchased by a group headed by M. J. Boylen, K. C. Irving, Maritime Mining Corporation, and the Patino Corporation. Construction of a mine plant and concentrator at the No. 12 mine commenced in October 1962 and the concentrator was placed in operation in March, 1961b. Preparation of the open pit mine for production, construction of the No. 6 Concentrator to produce bulk Pb-Zn-Cu-Ag concentrate from No. 6 ore, and construction of an Imperial Smelting Process smelter at Belledune were started in 1964 and placed in operation in September 1966.

Jan 1, 1970

By W. Mostowitsch, H. O. Hofman

The mineral gypsum, CaSO4 + 2 H2O, has been used for many years as a sulphurizing and basic flux in several smelting-operations. Thus, in smelting oxide nickel-ore in the blastfurnace, it is commonly added to the charge to furnish the sulphur necessary for collecting the metal in a matte, and a base for slagging the siliceous gangue. In the concentration of lead-copper matte in the reverberatory furnace it has been used for years at Preiberg, Saxony,1 for a similar purpose, and for producing at the same time a copper-matte with less than 0.15 per cent. of Fe. The latest use gypsum has been put to is in the blast-roasting process of Carmichael-Bradford.2 The term " blast-roasting," given by A. S. Dwight3 to the Dwight-Lloyd method of roasting and agglomerating: is a happy generic term which covers the ground better than the " lime-roasting " of Ingalls5 or the " pot-roasting " of Austin: in that it leaves the operation independent of the character of the flux and the form of apparatus, and retains the characteristic feature of this class of processes—namely, that of using forced draft. In the Carmichael-Bradford process the dehydrated material, mixed with galena-concentrate, acts as a diluent and a flux. The process differs in this from the Huntington-Heberlein7 and the Savelsberg8 processes, in both of which limestone is used.

Jan 1, 1909

By R. Q. Shotts

Data are presented which show that fractions of varying densities from the same coals are oxidized at different rates by nitric acid. From oxidation data, the approximate quantity of "bright" and "dull" components may be calculated. Definite relationships between oxidation rate and rank are shown for density fractions from at least two bituminous coals. IN 1945, the Alabama State Mine Experiment Station initiated a program on the determination of fusain in certain coals of the state.1 Because of the lack of equipment and personnel necessary for microscopic examination, the chemical method2 was used exclusively. During studies of the distribution of fusain in fractions of various sizes and densities on a medium volatile coal, the author noted a higher rate of oxidation of the nonfusain part of the coal in the lower density fractions and the difference in rate became more marked the shorter the oxidation period used. Since durain and other "dull" components of coal have been reported3,4,5 to have higher densities than vitrain and the bright components, it appeared probable that the observed differences in rates of oxidation in the different density fractions were due to variations in petro-graphic composition. Such effects have been noticed by other workers.2,3 In order to obtain further evidence on this point, several Alabama coals of different rank have been separated into three or more fractions on the basis of density and their rates of oxidation determined, using the procedure specified for the determination of fusain, except that measurements were made at short time intervals as well as for the longer periods specified in the regular procedure. Significant differences in the rates of oxidation of the nonfusain part of the various fractions have been observed, and it is believed that studies of this type may make possible the identification of individual petrographic components or lead to methods for their semiquan-titative estimation. Properties of the Coals: Analyses and some properties of the whole coals studied are given in table I. The range in rank of the coals is not the widest possible within the state, but samples of the low volatile coals that occur in thin beds in the northeastern part of the state, were unavailable. The Clements bed is not, at present, considered workable. The coal is of medium volatile rank, quite friable, and very strongly swelling. Analyses of different size fractions show that the larger sizes are of higher rank than the smaller ones. Material passing the No. 50 sieve (all sieve sizes refer to the U. S. Standard Series) is close to high volatile A in rank, except for the size passing a No. 200 sieve, in which fusain is partially concentrated. Because of the variation in rank of the sizes of Clements coal, oxidation studies were made of two widely different size ranges. The + 1-in. material was crushed on rolls to about 1/8 in. and separated into five fractions by float-and-sink treatment in a benzene-carbon tetrachloride mixture. The — No. 4 + No. 8 and the — No. 4 + No. 50 size ranges tested overlap but the latter size was studied last with the expectation that it would include more oxidizable material than the first size. This proved not to be the case. Yields and properties of the specific gravity fractions oxidized are shown in table II. Milldale bed coal probably represents, as nearly as it is possible to do so, the "average" coal of the state. The material passing a No. 4 sieve was the only size range oxidized. It was divided into four specific gravity fractions. As in every case the heaviest fraction, which was essentially rock, was discarded. The Black Creek is the most extensive in area of

Jan 1, 1951

By R. Q. Shotts

Data are presented which show that fractions of varying densities from the same coals are oxidized at different rates by nitric acid. From oxidation data, the approximate quantity of "bright" and "dull" components may be calculated. Definite relationships between oxidation rate and rank are shown for density fractions from at least two bituminous coals. IN 1945, the Alabama State Mine Experiment Station initiated a program on the determination of fusain in certain coals of the state.1 Because of the lack of equipment and personnel necessary for microscopic examination, the chemical method2 was used exclusively. During studies of the distribution of fusain in fractions of various sizes and densities on a medium volatile coal, the author noted a higher rate of oxidation of the nonfusain part of the coal in the lower density fractions and the difference in rate became more marked the shorter the oxidation period used. Since durain and other "dull" components of coal have been reported3,4,5 to have higher densities than vitrain and the bright components, it appeared probable that the observed differences in rates of oxidation in the different density fractions were due to variations in petro-graphic composition. Such effects have been noticed by other workers.2,3 In order to obtain further evidence on this point, several Alabama coals of different rank have been separated into three or more fractions on the basis of density and their rates of oxidation determined, using the procedure specified for the determination of fusain, except that measurements were made at short time intervals as well as for the longer periods specified in the regular procedure. Significant differences in the rates of oxidation of the nonfusain part of the various fractions have been observed, and it is believed that studies of this type may make possible the identification of individual petrographic components or lead to methods for their semiquan-titative estimation. Properties of the Coals: Analyses and some properties of the whole coals studied are given in table I. The range in rank of the coals is not the widest possible within the state, but samples of the low volatile coals that occur in thin beds in the northeastern part of the state, were unavailable. The Clements bed is not, at present, considered workable. The coal is of medium volatile rank, quite friable, and very strongly swelling. Analyses of different size fractions show that the larger sizes are of higher rank than the smaller ones. Material passing the No. 50 sieve (all sieve sizes refer to the U. S. Standard Series) is close to high volatile A in rank, except for the size passing a No. 200 sieve, in which fusain is partially concentrated. Because of the variation in rank of the sizes of Clements coal, oxidation studies were made of two widely different size ranges. The + 1-in. material was crushed on rolls to about 1/8 in. and separated into five fractions by float-and-sink treatment in a benzene-carbon tetrachloride mixture. The — No. 4 + No. 8 and the — No. 4 + No. 50 size ranges tested overlap but the latter size was studied last with the expectation that it would include more oxidizable material than the first size. This proved not to be the case. Yields and properties of the specific gravity fractions oxidized are shown in table II. Milldale bed coal probably represents, as nearly as it is possible to do so, the "average" coal of the state. The material passing a No. 4 sieve was the only size range oxidized. It was divided into four specific gravity fractions. As in every case the heaviest fraction, which was essentially rock, was discarded. The Black Creek is the most extensive in area of

Jan 1, 1951

By Norman L. Newbern, Robert E. Green

An investigation of the effect of size on the deformation properties of metal single crystals made it desirable to grow from the melt cylindrical aluminum single crystals possessing exactly the same crystallographic orientation but varying in diameter. Methods for the growth of rather large (up to 3 in. diam) aluminum single crystals in molds of the desired shape are well known. However, when one applies the same techniques to the growth of smaller (less than 1/8-in. diam) specimens many additional problems arise. Two of the major problems are the construction of the molds to be used and the removal of the thin specimens from these molds without deformation after growth has been completed. Also the problem of the constraint forces exerted by the mold on the specimen is much more pronounced for the smaller specimens. The technique described herein is a zone-melting method in which no mold is used since the surface tension of the molten metal and its oxide is sufficient to retain the melt. The specimen is suspended vertically in a manner similar to that of Keck and Golay.2 However, while Keck and Golay supported the specimen from both ends, the method used here supports the specimen only at the upper end. The surface tension of the molten aluminum and aluminum oxide contains the melt and suspends a length of newly grown crystal that has already passed through the molten zone until the weight of the newly grown crystal is equal to the component of surface tension holding the specimen together in the molten region. When the weight of the newly grown crystal is equal to the component of surface tension holding the specimen together the specimen pulls in two in the molten zone. The length of crystal which can be grown before this separation occurs varies with the diameter of the specimen and the size of the molten zone. In order to prevent the specimen from pulling in two a tube of glycerine is placed beneath the furnace in such a manner that the newly grown crystal passes into the glycerine which provides sufficient buoyancy to allow aluminum single crystals in wire form to be grown to lengths determined only by the length of the tube containing the glycerine. A schematic diagram of the experimental arrangement is shown in Fig. 1. The furnace used is constructed as follows. High-resistance nichrome wire is coiled on a 3/8-in. diam fused quartz tube. The distance between the windings is much less over a length of about 3/8 in. at the center so as to develop a hot spot. This core is located in the center of a 4-in. diam steel cylinder 5 in. in height and insulated from it by Kayolite. The temperature of the furnace is controlled by means of a thermocouple located near the central hot spot and a Minneapolis-Honeywell temperature controller. Temperature ins,ide the furnace is measured with a thermocouple and a standard potentiometer in the usual manner. By the above method it is possible to grow high-purity (99.99 pct Al) aluminum single-crystal wires over a range of sizes. Crystals varying from 1/8 to 1/64-in. diam were grown by the authors. Since the tube containing the glycerine cannot contain a crystal longer than approximately 3 ft, the growth of crystals longer than this presents another problem. It was found that one could cut the newly grown crystal without deformation in the region between furnace and glycerine tube try means of a cutting torch and then by moving the glycerine tube slightly aside continue

Jan 1, 1962

By R. Schuhmann, E. J. Michal

Experimental measurements are reported for the oxygen pressures of iron-silicate slags in equilibrium with solid silica. CO2-CO mixtures were bubbled through the slags in silica crucibles to find equilibrium values of p co2/p co over the entire composition range of silica-saturated slags at 1250°, 1300°, and 1350°C. From the data, the activity vs. composition relationships were calculated for O, FeO, and Fe. SLAGS composed primarily of silica and iron oxides have particular practical importance in copper smelting,' in acid steelmaking, and in accounting for the service behavior of silica refractories. These slags all contain both ferrous and ferric iron, so that, strictly speaking, they are ternary or three-component liquid solutions. For convenience, the components may be taken as the three oxides, FeO, Fe2O3, and SiO2. The constitution of the FeO-Fe,O,-SiO, system at slagmaking temperatures has been studied in a recent investigation described in a separate paper.' This work showed the compositional ranges of iron-silicate melts at temperatures up to 1450°C and also the temperature-composition relationships for melts in equilibrium with various solid phases, including iron, wüstite, magnetite, and silica. Broadly speaking, the compositions of iron-silicate melts at a given temperature should be thought of as varying over a two-dimensional field. In the first place, the silica/total iron oxide relationship varies from maximum silica for silica-saturated melts to minimum silica for wüstite-saturated melts or, at higher temperatures, to zero silica for straight iron oxide melts. In copper smelting, for example, the converter slags approach the low silica limits while the reverberatory-furnace slags have intermediate silica contents, perhaps approaching silica saturation in some circumstances. Liquids formed in the pores of silica refractories presumably are close to silica saturation. The second type of composition variation is in the ferric/ferrous relationship, which depends on how oxidizing or how reducing the process conditions are. Relatively reducing slags, such as acid-steelmaking slags, are lower in ferric oxide and ap- proach saturation with metallic iron. Oxidized slags, such as copper-smelting slags, contain larger percentages of ferric oxides and approach or reach saturation with magnetite. Since these two kinds of compositional variations are closely related to two general properties of interest for all metallurgical slags, basicity, and oxidizing power, it is hoped that the thermodynamic study of iron-silicate slags eventually will throw further light on the significance and nature of these long-recognized but as yet poorly understood slag properties. Measurements of oxygen activity as a function of slag composition, using CO-CO2 gas mixture to fix oxygen activities, afford an experimentally convenient approach to the study of the thermodynamic properties of iron-silicate slags. In a preceding investigation,³ his approach was used in a systematic study of iron-silicate slags in equilibrium with solid iron. The present paper gives the results of a similar study of the iron-silicate slags in equilibrium with solid silica. The experimental work consisted in the determination of CO2: CO ratios in gas mixtures at equilibrium in the system: gas: liquid slag: silica Determinations were made at temperatures from 1250° to 1350°C for slags ranging in composition from iron saturation to magnetite saturation. Also, equilibrium CO,: CO ratios and slag compositions were determined for the univariant systems: gas: liquid slag: silica: iron gas: liquid slag: silica: magnetite Experimental Methods The experimental procedure was essentially the same as that used in the previous study of iron-silicate slags saturated with solid iron," but in order to work with the silica-saturated slags an all-silica crucible assembly was used. A liquid slag was prepared from pure prefused stock materials and brought to equilibrium with the silica crucible at the desired temperature. Then a mixture of CO2 and CO was continuously bubbled through the melt

Jan 1, 1953

By H. H. Hasler

THE mining and removal of coal from two or more beds, either simultaneously or consecutively, in vertically adjacent areas have always been matters of concern to mine operators from both operating and recovery points of view. However, with the progressive introduction and use of electrical and mechanical facilities, such problems assume even greater proportions. In this paper typical cases occuring in Cambia County, Pa., are given and procedures whereby such problems may be .greatly reduced, if not entirely eliminated, are suggested. Throughout a considerable portion of the Central Pennsylvania bituminous coal region, particularly in Cambria County (Fig. I), the portion of the region to which references in this paper are made, large areas are encountered where two or more beds of coal occur and have been mined extensively since the earliest days of mining in the county. Generally, operations were commenced in one bed of coal on a property, following which, as conditions appeared to warrant, operations were commenced in another bed or beds on the same property, in some instances by the same operator. Operating results by no means have been uniformly successful, as the following review of some typical cases indicates, partly because of lack of experience in earlier cases and in certain later cases to disregard for the experiences of earlier operators. It is suggested that repetitions of such failures may be reduced largely, if not eliminated entirely, by adherence to a few basic principles founded upon past experiences. Geology and Stratigraphy The geology, stratigraphy, and relief of almost all of Cambria County have been studied and reported at length by the U. S. Geological Survey in its Johnstown, Ebensburg and Barnesboro-Patton Folios and other publications, by the Pennsylvania Geological Survey and by various individuals. All exposed rocks occurring within the boundaries of the county are of sedimentary origin, consisting of alternate beds of sandstone, slate, shale, fireclay, coal, limestone, etc., and all have been classified by the U. S. Geological Survey as extending from the upper strata of the Catskill formation, Devonian system, to and including, in a few hilltop areas, the lower strata of the Monongahela formation, Carboniferous system. Included within that range is the Allegheny formation, Pennsylvania series, which embraces all of the commercially important beds of coal that occur in the county, viz., the A, or Brookville, to the E, or Upper Freeport, both inclusive, shown in Fig. 2. The measures are traversed by a series of anticlines and synclines, extending in a northeasterly and southwesterly direction, which form broad, gently sloping basins (flat to 15 pct pitch, exceptionally to 25 pct). However, the topography of the surface is such that long lines of outcrops of all beds of coal overlying bed B, and to a limited extent bed B also, occur over large areas, a factor which contributed to the early and extensive development of mining activities in the county. Earliest mining developments of commercial importance were made in B, C', D, and E beds of coal, and it is in these beds that the principal mining operations are being conducted. To a limited extent, mining operations also have been conducted in local areas in the A, B rider and C beds. Coal beds being mined today range in thickness from approximately 28 to 60 in. Intervals between the respective beds of coal are variable but conform somewhat to the following general averages: A to B, 60 to 100 ft.; B to C, 50 ft.; C to C', 70 ft.; C' to D, 45 ft.; and D to E, 45 ft. The following are typical mining cases obserced over a period of years in various parts of the county.

Jan 1, 1952

By M. J. Marcinkowski, K. S. Sree Harsha

A detailed numerical analysis has been made of the equilibrium configuration of partial dislocations in a blocked deformation twin under an externally applied stress. Twins made up of both pure screw and pure edge partials have been considered. The components of stress in the vicinity of the twin tip associated with each of these configurations have been plotted. It has been found that at some critical degree of oblateness the shear stress fields of the blocked screw or edge twin can both sPontaneously nucleate slip, whereas only the component of stress oxx about the edge twin can nucleate and propagate cracks. TWINNING becomes a predominant mode of plastic deformation at low temperatures and/or high strain rates. Fig. l(a) shows what must be the first step in the formation of a deformation twin, namely the formation of a loop of imperfect dislocation bounding a stacking fault. In an fcc crystal the partial dislocations have Burgers vectors of the type 1/6 a,(112) and the fault is of the intrinsic type while in the bcc crystal the partials have Burgers vectors of the type ao(lll). The stacking sequence of (111) planes in a perfect fcc crystal is given by ABC ABC, and so forth, and in one which contains a twin by ABCABACBA, and so forth. It is apparent that the stacking fault and twin give rise to no mistakes associated with adjacent close-packed planes; however, with respect to second-neighbor close-packed planes the faulted crystal has twice as many mistakes as the twin. The energy of the twin boundary may thus be taken to be one-half that of the intrinsic fault boundary. In the case of the bcc crystal the stacking sequence of (112) planes is given by ABCDEFABCD, and so forth, in a perfect crystal, by ABCDCDEFA, and so forth, in a crystal which contains a fault, and by ABCDCBAF, and so forth, in one which contains a twin. An analysis similar to that applied in the fcc crystal shows that both the fault as well as the twin involve no neighbor violations across adjacent planes. However, there are twice as many violations across second-neighbor (112) planes associated with the fault as compared to that of the twin. Thus once again the energy of the twin boundary may be taken as one-half that of the fault. It is important to note that, unlike the fcc, the faults in the bcc crystal involve first nearest-neighbor violations and are thus expected to be of much higher energy than those in fcc crystals. A more detailed analysis of the material discussed above can be found in Ref. 1. To a good approximation then, the lenticular twin shown in Fig. l(b) can be generated by adding partial dislocation loops on successive (111) planes for fcc crystals or (112) planes for bcc crystals in the manner shown, with no additional expenditure of chemical energy other than that required for the fault shown in Fig. l(a). In practice, deformation twins are much more extended than that shown in Fig. l(b) and more closely resemble one shown schematically in Fig. l(c). It is readily apparent that the free energy of the twin and matrix are identical. In those cases where the partials lead to a structural change, the free energy of the material contained within the dislocation array is lower than that of the matrix and we have the so-called martensite transformation. The present investigation is the first in a series of five major theoretical-experimental efforts which will deal with the static and dynamic behavior of twin nucleation and growth. There has been a recent surge in activity pertaining to the equilibrium shapes of twin lamellae2'3 and

Jan 1, 1969

By Charles C. Towle, Irving Rapaport

URANIUM mineralization along the north flank of the Zuni Uplift, in the vicinity of Haystack Butte, was discovered by Paddy Martinez, a Navajo Indian, in the spring of 1950. The find was reported to the Santa Fe Railway Co., which initiated a program of exploration upon its holdings in the district in December of 1950. The Anaconda Copper Mining Co. secured numerous leases in January and February, 1951, and began an intensive exploration and development program in March 1951. The district was extended into the Lucero Uplift in August of 1951 by the discovery of uranium mineralization in Todilto limestone by Joy Sinyella, a Supai Indian living on the Laguna Reservation. Initial reconnaissance was performed in the district by the Atomic Energy Commission in November 1950. A field office under the direction of the Denver Exploration Branch of the AEC was established at Prewitt, N. Mex. in January 1951 to study regional and detailed guides to ore, to evaluate the ore deposits, and to promote the development of the district by providing geologic services for the companies and individuals engaged in exploration. With the development of sufficient ore to warrant construction of a mill, the Grants area of New Mexico has come of age as a full fledged uranium mining district. The carnotite-type deposits of Grants, the first of major economic importance found in limestone, have extended the Colorado Plateau carnotite field into the more complex structure of the Basin and Range Province. General Geology The Grants uranium district is in northwestern New Mexico, along the southern flank of the San Juan Basin, between the cities of Gallup and Albuquerque. The region is at a mean altitude of about 6800 ft, vegetation is sparse, and outcrops are excellent. Mt. Taylor volcanic peak, at an elevation of 11,400 ft dominates the surrounding area. The overlying cliff-forming Dakota sandstone is the most resistant formation in the Grants District and characteristically erodes into dissected mesas as much as five miles wide. The principle uranium ore-bearing horizons are found in the underlying Morrison formation, and the Todilto limestone of the San Rafael group. The Morrison weathers into. a series of steep slopes and precipitous cliffs near the lower part of the Dakota-capped rims, while in contrast, the relatively resistant underlying. Todilto [ ] limestone forms broad benches extending out from the base of these Dakota rims as much as five miles wide. The Todilto benches are covered with overburden to an average depth of about 5 ft in the first thousand ft away from the Dakota rim, but increases to about 200 ft at the base of the rim. In many places however, a thick mantle of upper Cretaceous sediments and Tertiary volcanics "obscures the ore-bearing Jurassic, and precludes exploration. . The known uranium deposits of the Grants District are distributed throughout a zone 85 miles long and about 10 miles wide. Stratigraphy Rocks from pre-Cambrian through Tertiary are exposed in the uplifted areas, but uranium appears to be restricted chiefly to two zones in Jurassic sediments. The Jurassic sediments of the Colorado Plateau have been subdivided into three units, in ascending order: (1) Glen Canyon group, (2) San Rafael group, (3) Morrison formation. The Todilto limestone zone within the San Rafael group has produced the bulk of ore to date, but the promise of the Morrison zone is rapidly increasing. The Todilto formation extends about 300 miles east-west and about 100 miles in a north-south direction. It is composed of a lower, extensive, limestone member and a central, more restricted, thick, pure gypsum member. The Todilto is believed to be of lacustrine origin. The Morrison formation in this area is subdivided, rather arbitrarily, into three members: Recapture Creek, Westwater Canyon, and Brushy Basin. Ore

Jan 1, 1952

By W. W. Mein

IN March 1949 the Calaveras Cement Co. was sued by five landowners whose properties are located in the vicinity of the plant. These landowners—all of them cattle ranchers—sued for dust damages of $120,338 and for an injunction preventing the company from casting dust upon their properties in injurious quantities. The issue was split, the jury deciding the amount of damages and the court handling the injunction features. The action came to trial before a jury in April of that year and resulted in damages being awarded in the amount of $7,508. A month later the court issued its injunction requiring recovery of stack dust to an 87 pct minimum. The Calaveras plant, shown in Fig. 1, is located three miles from San Andreas in the heart of the Mother Lode country, about 45 miles east of Stockton, Calif. Since it is in a small town, the company's responsibilities to its employees and to the community are different from those of plants located in large centers of population. Construction of the plant was begun in 1925, and production was started the following year. Standard gray Portland cement as well as several specialty cements are produced. Production facilities have been continually enlarged so that the present capacity is more than double what it was 25 years, ago. The most important item in the company's expansion program was the purchase in 1945 of an 11 ft 3 in. x 360 ft Allis-Chalmers kiln which had been declared surplus by the Defense Plant Corp. The company is now able to produce about 2,500,000 bbl of cement a year, and employment at the plant is approximately 300. The production of cement has always involved a dust problem, solution of which has been attempted in a number of different ways. By far the most efficient method of catching dust discharge is electric precipitation. Soon after the company went into production in the 1920's, the landowners near the plant began complaining about dust discharge. The company settled the matter by paying them a total of $27,000 for dust damages incurred during the period from 1929 to 1938. In the latter year the two-unit Cot-trell Electric Precipitator shown in Fig. 2 was installed and collected over 85 pct of the dust resulting from operation of the two 11 ft 3 in. x 10 ft x 240 in. kilns. From 1938 until 1946 the landowners registered no objection and were apparently satisfied with that dust recovery. In 1946, however, the substantially higher production resulting from operation of the new kiln immediately overtaxed the facilities of the existing two-unit precipitator. In a short time claims for dust damages were again received from the landowners. The company informed them that because of postwar shortages it would take several years to install a new precipitator. The company stated that it intended to purchase an additional precipitator and offered in the meanwhile to pay the landowners a fair amount to cover their damages. This offer was rejected and the landowners filed suit in the Superior Court of Calaveras County asking for total damages of $120,-338 and for the injunction outlined above. Case for the Ranchers The attorneys for the plaintiffs produced three different types of witnesses: first, the landowners themselves and members of their families; second, other cattle raisers who were sympathetic to the plaintiffs; and third, several types of technical experts: veterinarians, soil chemists, and an aerial photographer. The testimony of these witnesses was designed to establish that the flue dust from the plant had not only damaged the land and the forage, but had also caused fluorine poisoning to their animals. By a combination of these causes, the plaintiffs attempted to prove substantial loss of profits.

Jan 1, 1952

By W. B. Gogarty

With the use of polymer solutions in secondary recovery operations, the need has developed to understand the mobility control mechanism. This study investigated mobility control by considering both permeability and rheological effects. Experiments used a high molecular weight, partially hydrolyzed polyacrylamide polymer. Flow studies took place in reservoir and Berea cores having zero oil saturation. Effective size of the polymer flow unit was inferred from Nuclepore filter tests. Clay studies indicated the particle size capable of decreasing the core permeability. Flushed permeabilities measured the approximate core permeabilities with flowing polymer solutions. These permeabilities were considerably lower than original values. With mobility data and the flushed permeability, maximum effective viscosities were determined for polymer solution flow in a core. Effective viscosities showed that rheological properties play an important part in mobility control with polymer solutions. The study showed that permeabilities decrease and stabilize with polymer flow. At the lower permeabilities, high shear rates exist in the cores. Because of the pseudoplastic character of the polymer solution, the high shear rates caused low effective viscosities. This condition pointed to the inefficient use of the potentially high viscosity of the polymer solution at low shear rates. INTRODUCTION In the oil industry, a great deal of interest is being shown in the use of polymer solutions for secondary recovery and a number of polymer floods are being performed in the United States.1 Some of these floods have become commercial while others have been reported as failures. A number of floods are still in progress and remain to be evaluated. With the advent of polymer flooding, the need developed to understand the mobility control mechanism in porous media. Rheologically, the polymer solutions behave as pseudoplastic fluids. Investigators have studied the rheology for this type of non-Newtonian fluid in porous media?-6 Results have also been reported on the ability of polymer solutions to decrease mobility.7-10 Some investigators indicated that polymer solutions show a different rheological behavior in cores than on the viscometer.7,8 This study is representative of an initiatory investigation on mobility control with polymer solutions. Some effects are considered on a qualitative basis. Mobility control is considered from the standpoint of both permeability and rheology and, to the extent possible, permeability and rheological effects are considered separately. Results show that mobility control occurs from a reduced permeability caused by polymer retention and an effective viscosity determined by the average shear rate in the core. In this respect, rheological behavior is as important in mobility control as permeability. PROCEDURES A high molecular weight, partially hydrolyzed, polyacrylamide polymer was used in the investigation. Solutions of various concentrations were made with this polymer in different types of water. Some solutions used distilled water and others used tap water. The tap water contained approximately 500 ppm dissolved solids. As used in this paper, concentrations in ppm refer to parts by weight solute to one million parts by weight of solvent. In the tap water, calcium and magnesium accounted for from 60 to 80 ppm of the solids, the remainder being mostly sodium chloride. All solutions contained a bactericide, and anti-oxidants and antiprecipitants were added to the tap water. Capillary and concentric-cylinder* viscometers determined the rheological properties of solutions. The capillary viscometer is described elsewhere.6 Berea and reservoir sandstone were used as core materials for this investigation. Cores were 1 in. in diameter by approximately 2 to 3 in. long. Prior to mounting, the Berea cores were heat-treated for 3 hours at 850F. This treatment decreased the water-sensitivity of the clays in the cores. The reservoir cores were cleaned with solvent and