Search Documents

By W. E. Showalter

This paper discusses some of the results of combstion-drive tests which were made in a test cell using a sand bed 10 in. in diameter x 10-ft long. The test method is illustrated and described. The relationship between the API gravity of the in situ oil and the amount of air required for combustion drive is discussed in detail. Other things constant, the air requirement for combustion drive increases as the APl gravity of the in situ oil decreases. If the test results apply to actual reservoirs, the lowest-priced oils may cost the most to recover by this method. Information is shown which indicates that the effect of pressure on the amount of hydrocarbon burned is not large. A method of predicting air requirements from the API gravity of the in situ oil is presented. INTRODUCTION Combustion drive is the term used to identify the process of interstitial or in situ burning as an oil recovery method. Part of the in situ oil is burned to generate the energy needed to produce the remainder of the oil. Combustion drive as an oil recovery mechanism remains an economic uncertainty in spite of all the work that has been done by the industry in both laboratory and field?-6 This paper will show some of the results of tests which were made in a test cell for the purpose of studying the nature of the combustion-drive process. It will present data which indicate that the API gravity of the in situ oil is a significant indicator of the amount of air required to drive a burning front through oil sand. Air requirement varies inversely as the API gravity of the in situ oil. EXPERIMENTAL The tests were performed in a cell which utilized a cylindrical sand section 10 in. in diameter x 10-ft long. The thin-walled metal pipe which held the sand was wound with twenty external electrical resistance heaters which, by means of an automatic controller, maintained adjacent sections of the wall of the pipe at temperatures equal to the temperatures of the contained sand. Each heater covered 6 linear in. of the pipe. By this means lateral heat loss from the sand section was minimized, thereby causing the sand section to simulate more closely a horizontal increment of a combustion-drive reservoir. Fig. 1 shows a schematic diagram of the test assembly. Thermocouples to measure the temperature in the sand were located every 6 in. along the length of the sand section. The pipe containing the sand was enclosed in a cell designed for an operating pressure of 500 psig. The inlet air pressure was controlled at the inlet, and the gas flow rate was controlled and measured at the outlet of the cell. The oil sand used for the tests was prepared by mixing first water and then oil with the noncon-solidated sand using a closed mixer similar to a cement mixer. Table 1 shows a screen analysis of the sand. Ninety percent of the sand was 100 mesh or finer. This sand was a mixture of 80 per cent No. 120 Nevada White Sand and 20 per cent Tennessee Hi-Fusion Moulding Sand No. 3. The Nevada sand was a clean silica sand. The Tennessee sand con-

By J. S. Crump, C. R. Hocott, A. E. Hoffman

Planning of the efficient operation of a gas-condensate reservoir requires a knowledge not only of the gross phase behavior of the system but also of the equilibrium distribution of the various components between the gas and condensate phases. This equilibrium distribution can be calculated with appropriate equilibrium constants. In this paper are presented equilibrium constants determined experimentally for the oil and gas phases initially present in the same reservoir and for the gas and condensate phases of the gas cap material at a series of pressures below the original reservoir pressure. Also presented is a method for the correlation of the experimentally determined equilibrium constants. The utility of the correlation is demonstrated further by an example of its use in adjusting the equilibrium data to permit their application to another gas-condensate system of similar composition. INTRODUCTION Planning of the efficient operation of a gas-condensate reservoir requires a thorouugh knowledge not only of the gross phase behavior of the particular hydrocarbon system but also of the equilibrium distribution of the various components between the gas and condensate phases. At the initial conditions of reservoir temperature and pressure, the original hydrocarbon materials in a gas-condensate reservoir or in the gas-cap of an associated reservoir exist in a single, homogeneous vapor phase. However, some condensation of hydrocarbons to a liquid phase usually occurs in the reservoir as pressure declines incident to production. Because of this condensation. the produced gas changes composition continuously. The composition of the produced gas, as well as that of the condensed liquid, can be calculated from the composition of the original reservoir material through the application of appropriate equilibrium constants or "K"-values provided these values are known. Equilibrium constants have been used for many years in problems of surface separation of gas and oil and natural gasoline recovery. However, no satisfactory equilibrium data at reservoir conditions have been available for the higher boiling hydrocarbons which acquire abnormal volatility at high pressure and are therefore present in the gas phase in condensate reservoirs. Early work in this field indicated that the behavior of the higher boiling hydrocarbons largely determines the behavior of gas-condensate systems at high pressure.' Consequently, a portable test unit was designed to permit determination of the distribution of the heavier hydrocarbons between the gas and liquid phases of a gas-condensate system. This paper describes the test equipment and presents the results of an investigation of the reservoir fluids from an associated oil and gas reservoir in the Frio formation in Southwest Texas. Also presented is a method for correlation of the experimentally determined equilibrium constants, together with an example of the use of the method in adjusting these data for application to another gas-condensate system of similar composition. FIELD TESTING AND SAMPLING In order to determine the compositions of the reservoir fluids, field samples were secured from two different wells, one completed in the oil zone, and one completed in the gas cap. The oil well was completed through perforations in 51/2-in. casing at a depth of 6,822-6,828 ft subsea. Pressure and temperature traverses made in the well indicated the pressure and temperature to be 3,831 psig and 201 °F, respectively, at a depth of 6.828 ft subsea. Subsurface samples were taken from this well after a four-hour shut-in period.

Jan 1, 1953

By R. D. Mollison, C. F. Fogarty

Sulfur is widely distributed in nature. It is present in the earth's crust, the ocean, the meteorites that come to us from cosmic space and in practically all animal and plant life. According to Clarke,9 the earth's crust contains 0.06 pct sulfur. Large quantities of free or combined sulfur are found in coal, natural gas and petroleum. Mineral waters contain sulfates and hydrogen sulfide. Sulfur is rather plentiful in the crust of the earth; however, only under special circumstances can it be produced profitably. Sulfur is one of the cheapest raw materials used by industry; and, therefore, the economic feasibility of a given deposit is strongly dictated by the law of supply and demand on local as well as world-wide levels. The forms which are commercially important are elemental sulfur or brimstone, and the sulfides such as pyrite (FeS2), pyrrhotite (FenSn+1), chalcocite (Cu2S), sphalerite (ZnS), and galena (PbS); the sulfates such as gypsum (CaSO4,2H2O), anhydrite (CaSO4), and kieserite (MgSO4,H2O). Elemental Sulfur Elemental sulfur is found in many localities, generally in solfataras and gypsum type deposits. The solfatara deposits are found commonly in the neighborhood of active or extinct volcanoes as in Italy, Japan and Chile, or fumaroles associated with mineral springs such as the Mammoth Hot Springs in Yellowstone Park. Here the sulfur is deposited in tufas or other porous host rocks. This type of sulfur deposit probably results from the oxidation of hydrogen sulfide or the reaction of hydrogen sulfide with sulfur dioxide. Most of the world's supply of elemental sulfur comes from the gypsum-type deposits. Here the mineral occurs as either crystalline or amorphous sulfur in sedimentary rocks in close association with gypsum and limestone. This association is characteristic and occurs in almost all the great gypsum beds of the world, although sulfur is not always present in quantities of economic importance. Various theories have been advanced to account for this association. Bischof5 suggested that the sulfur came from hydrogen sulfide which resulted from the reduction of calcium sulfate by carbon or methane in accordance with the following reactions: CaSO4 + 2C= CaS + 2CO2 CaS + C02+ H2O = CaCO3 + H2S CaSO4 + CH4= CaS + C02+ 2H20 2H2S + 02= 2H20 + 2S All of the sulfur-bearing domes on the Gulf Coast have calcium sulfate in great quantity in the cap. They all show the presence of hydrocarbons. The oxygen for the final reaction could have been supplied by circulating ground waters. The principal objection to this theory is that temperatures of 700° to 1000°C are needed to reduce the sulfate to sulfide with carbon compounds. The geologic evidence is that the temperature of the sulfur-bearing domes of Texas did not exceed 100°C. Proponents of the theory say that geologic time or a catalyst replaced temperature. According to another theory the sulfur in the salt domes is the result of bacterial action. Sulfate reducing bacteria have been detected in sulfur cores and in the formation water issuing from salt domes. It has, therefore, been suggested that these bacteria converted the sulfate to sulfide which subsequently was converted to elemental sulfur.

Jan 1, 1960

By H. W. Hockin, D. r. Brandt, R. H. Walsh, P. L. Dietz, P. R. Girardot

New Jersey, Florida, and Canadian ilmenites were reduced with hydrogen or coke under various experimental conditions and the phase changes occurring in the ilmenite upon reduction have been studied by microscopic examination of polished sections and by X-ray diffraction. The products formed were dependent upon the type of ilmenite, temperature, time and reducing agent. Of the reducing agents, hydrogen was the more effective at lower temperatures. 1 HE possible utilization of ilmenite as a source of both iron and titanium has resulted in the development of a number of methods for the separation of the iron and titanium content. Slagging processes as currently used in Canada are typical of such methods. Somewhat less attention has been given industrially to the reduction of the iron content at less than the slagging temperature. Although references maybe found to such work, in general only one type of ilmenite, either natural or synthetic, has been studied by each author. We have attempted to draw some relationship between the results of experimental reduction and the type of deposit from which the ilmenite was derived, as evidenced by phases occurring in the ores and in the reduction products. Ilmenite ores having from 27 to 61 pct titanium dioxide were included in this study and in each case reduction was carried out at such temperatures that only limited coalescence of the particulate iron product occurred within the ilmenite grains. The history of the individual ilmenite samples and the temperature of reduction were found to determine the occurrence of various phases and the mode of distribution of the iron. REVIEW OF EARLIER WORK ON REDUCTION One of the earliest references to the reduction of ilmenite at less than the slagging temperature was made in 1917.' The metallic iron produced was_____ leached out by the action of dilute sulfuric or hydrochloric acid, to leave a product high in titanium dioxide. Subsequent to this, numerous patents2-'? and other references13"21 have appeared concerning reduction of ilmenite by carbon, hydrogen, carbon monoxide, methane, coal gas, water gas, or the like in the absence of fluxing agents. Mineragraphic examinations were not reported, and in the main, the only examinations made were chemical analyses. However, in two cases3,13, titanium suboxides were reported in the products and in one case2' rutile was reported, in addition to metallic iron. Both were identified by X-ray diffraction. While reductions in the absence of fluxing agents were generally followed by either a wet or dry chemical process for removal of the metallic iron, a Canadian source17 reported removal of the metallic iron by magnetic separation. By the addition of fluxing agents during reduction, the metallic iron has been coalesced into "pearls." Each reference to such a process23-28 has shown that the coalesced iron could be removed by magnetic or gravity means after the product was crushed. In the absence of fluxes, the coalescence did not generally occur. The major part of the present study has been limited to reductions without fluxing agents in order to determine the primary reactions of naturally occurring ilmenites. Titaniferous iron ores have also been studied,29-33 17, l9 their reduction having been used as the basis of a commercial process for beneficiation of such ores in Norway29 and more recently considered in the United States34,35. The ease of reduction of titaniferous iron ores relative to that of hematite or magnetite has been referred to,33 with the conclusion that the more

Jan 1, 1961

By F. W. Luersson

High carbon, low phosphorus steel can now be made from pig iron containing 0.7 pct P or more, in a commercial sized open hearth furnace. No external heat is required for refining, and steel produced is identical with basic open hearth steel. THE classical Thomas process, which requires liquid pig iron containing over 11/2 pct P, yields a product relatively high in phosphorzs and nitrogen. Unless large quantities of recarburizers are added to the refined steel, the product is low in carbon content. Thus, the Thomas process is not well suited to American raw materials, and its product is often not acceptable according to the standards set by American industry. The shortcomings of the Thomas process have long been recognized; with the advent of low cost oxygen, studies were initiated to develop pneumatic processes which would conceivably overcome the inherent objections to Thomas steelmaking. Several such modified basic pneumatic processes have been tested experimentally in commercial trials during the past decade. Probably the most widely publicized of these developments has been the oxygen converter process as practiced in Austrial,2 and in Canada.8 n this process, oxygen is substituted for air and introduced above the liquid bath in order to increase the heat available to the metallurgical system. This avoids the need for high phosphorus raw materials and gives a product low in nitrogen. In this process, the phosphorus content in the final product depends, to a considerable extent, on the total amount of that element in the burden. The rotary furnace4 which is now in commercial operation at Domnarvet Steelworks, Sweden, is producing low phosphorus steel from iron containing 1.8 to 2 pct P. One or more early slags are removed and by this means high carbon steels of open hearth quality can be produced. At this stage of development there is some question as to the applicability of the rotary process to large heats. Another development has been the use of oxygen in combination with either steam6 or carbon dioxide yn the basic bessemer, thus avoiding the introduction of nitrogen gas into the refining system and giving a product relatively low in nitrogen content. A double slag process has been used in Europe7 in conjunction with a regular Thomas converter, by means of which it is possible to obtain a phosphorus content in the product approaching that obtained in basic open hearth steels. The Turbo-Hearth process:' which uses the side blowing principle so as to produce low nitrogen steel from normal American pig irons, has been developed experimentally in this country. A process fitted to U. S. raw materials All of the preceding processes, with the exception of the rotary furnace, suffer from the common shortcoming that they cannot be adapted to the production of high-carbon, low-phosphorus steels unless large proportions of recarburizers are added. In 1947, a program was initiated by the Inland Steel Company1' to study an oxygen steelmaking process specifically designed to utilize the full range of phosphorus analyses encountered in American pig irons and to give finai products with phosphorus and nitrogen contents comparable to steel produced by the basic open hearth process. Some of the objectives of the proposed process are: 1) the process should be able to accommodate molten pig iron conta;rl;rrg up to 1 pct P., 2) sne process should be subject to close control of carbon analysis, 3) the process should be capable of producing high carbon

Jan 1, 1958

By M. C. Smith, W. V. Green, D. M. Olsen

The creep-rupture behavior of commercial powder-metallurgy molybdenum rod is reported in the temperature range 1600" to 250O°C, at stresses up to 9000 psi and times up to 1 month. The effects of temperature, stress, and grain growth are discussed. Rupture time is fitted to the Larson-Miller parameter and compared to lower-temperature and higher-stress results reported by pugh.1 BECAUSE of its high melting point, molybdenum should retain useful strength to relatively high temperatures. Combined with its ready availability in the United States, this makes it attractive for many applications in missiles, rockets, and so forth—wherever its susceptibility to oxidation can be tolerated or overcome. The mechanical properties of molybdenum rod in the temperature range —200" to 1540°C have been reported by pugh,' Bechtold,' Parke,3 and Carriker and Guard.4 Madden and chen5 have measured the tensile properties of molybdenum single crystals in vacuum up to about 2500°C. As one further step in evaluating its mechanical usefulness, the constant-load creep-rupture properties of commercial powder-metallurgy molybdenum rod have been investigated in the range 1600" to 2500°C. MATERIAL TESTED Creep specimens were machined from 1/2-in. round commercial molybdenum rod, manufactured from powder by pressing, sintering, and swaging. Spectrochemical analysis of the rod showed "traces" (less than 0.01 pct) of silicon, aluminum, chromium, iron, and zirconium, and "faint traces" (less than 0.001 pct) of manganese, magnesium, cobalt, and nickel. Carbon content was 130 to 200 ppm, nitrogen was 110 to 180 ppm, and oxygen 30 to 35 ppm. A typical microstructure of the as-received rod is shown in Fig. 1. Room temperature tensile properties for five specimens strained at about 0.015 in. per in. per min are shown in Table I. CREEP SPECIMENS USED The specimens used for creep-rupture testing are illustrated in Fig. 2. The 1/4-in.-diam gage section was 3/4 in. long, and terminated at shoulders 5 mils high. These shoulders served as fiducial marks for optical strain measurements. Surface finish on the gage section was 16pin. r.m.s. One specimen, for a "long-time" test described below, was modified by dividing the 3/4-in. gage length into three 1/4-in. long sections with individual diameters of 0.250, 0.230, and 0.210 in., each terminating in a pair of fiducial shoulders. TESTING PROCEDURE The constant-load creep-testing machine used has been described by Smith, Olson, and Brown.6 In it the specimen is held vertically on the axis of a cylindrical tantalum or tungsten heater tube by threaded molybdenum or tungsten grips. Both specimen and grips are heated by radiation from the heater-tube, which is heated by its own electrical resistance. The bottom specimen grip is held at its lower end by a clevis pin. The testing load is applied to the specimen through the upper grip by means of hanging weights, a constant force-multiplication lever system, and a pull rod sealed to the chamber lid by a bellows. The incandescent specimen is viewed by an external optical system through slots in the heater-tube and radiation shielding, and an enlarged image of it is projected on a ground-glass screen. Gage-length measurements are made on this image with a pair of cathetometers. Thorium oxide coatings were applied to the threaded ends of most specimens, to prevent diffusion-welding of specimens to grips during testing. Without such a coating welding usually occurred, and grips were often broken by subsequent efforts to remove the tested specimens.

Jan 1, 1960

By J. N. Anderson

Developments in reverberatory furnace practice at Noranda over the period 1928 to 1953 are described. Features of interest are increasing furnace tonnage from 700 to 2000 tons per furnace day, the use of the suspended basic roof, and improvements in furnace fuel ratio. Points of comparison and contrast between Canadian and American furnace practice are given. OPERATIONS at the Noranda smelter have been described in a series of papers published between 1930 and 1945.1-4 In the present paper the development of reverberatory furnace practice over the 25 year period from the beginning of operations up to the present time will be reviewed and current furnace practice will be described in some detail. Particular attention will be given to those features which are characteristic of Canadian practice: first, the use of the suspended basic roof; second, the deliberate driving of furnaces to give tonnages in the range of 1400 to 2000 tons of solid charge per furnace day; and third, the continuous operation of furnaces at high tonnage for many years without any extended shutdown for repairs or rebuilding. Finally, points of comparison and contrast between reverberatory furnace practice in Canada and the United States will be discussed. The Noranda smelter, which started in December 1927, was built for the reduction of ore from the Horne mine where early development had shown a comparatively small tonnage of rich cop-per-gold ore of a grade and character which would require direct smelting. The smelter was designed for a capacity of 1000 tons of ore a day and originally consisted of eight roasters, two reverberatory furnaces, and two converters, together with necessary auxiliaries. The discovery of a large new body of ore in 1928 made it necessary to increase both the size and the scope of the reduction plant. A mill which was ultimately brought to a capacity of 3000 tons a day was built for concentrating low grade ore and in addition the capacity of the smelting plant had to be greatly expanded, so that for the next fifteen years every effort in the smelter was directed toward achieving maximum tonnage. Because the layout and design of the smelter made it impracticable to add a third furnace, it was necessary to increase the tonnage on the two original furnaces by improvements in furnace design and operation, roasting and converting equipment being added as required to meet the demands of increased furnace capacity. The smelter tonnage, which reached a peak in 1941, was curtailed in 1944 when it became necessary to operate on a one-furnace basis because of a reduction in the output of the Horne mine due to a shortage of labor. Two-furnace operation at a moderate tonnage was resumed in 1949. In the early years the smelter tonnage was made up almost entirely of Noranda ores and concentrates. However, since 1937 an increasing tonnage of ores and concentrates from other mines has been treated in the smelter. In recent years, with decreased production from the Horne mine, copper concentrates from several mines in the district, treated on a custom basis, have formed an important part of the smelter tonnage. A review of developments in reverberatory furnace practice at Noranda falls naturally into the following four periods: 1—1928 to 1935, the early years; 2—1935 to 1944, the period of greatest change and development; 3—1944 to 1949, one-furnace op-

Jan 1, 1955

By J. L. Fitch, B. G. Hurd

The presence of gypsum in samples subjected to standard core analysis introduces serious errors in the measurement of water saturation and porosity. The magnitude of these errors, depending upon the type of analysis procedure used, has been evaluated experimentally and theoretically. Water-saturated pore volumes determined by vacuum distillation or retort procedures may be too high by as much as 48 per cent of the volume of gypsum present. The maximum error in this value determined by Dean-Stark extraction with toluene is 36 per cent of the gypsum volume. If pore space is measured by a Boyle's law type porosimeter the maximum erorr due to gypsum is 38 per cent of the original gypsum volume present. The conscientious core analyst may eliminate the errors caused by gypsum by either of two methods. He may apply suitable corrections for the water of crystallization removed from gypsum, or take special precautions to prevent dehydration of gypsum during core cleaning and alzalysis procedures. These alternatives are discussed and methods for obtaining reliable core analysis data are proposed. Gypsum (CaSO4 . 2H2O) occurs as a common mineral in many of the world's sedimentary basins. In addition to its presence as primary bedded evaporitic deposits, it is often found as secondary replacement zones and pore-fillings in host rocks. That it may cause false indications in porosity, both on neutron logs and in standard core analysis, has been generally recognized. False porosity interpretations from neutron logs result because the chemically bound water in gypsum attenuates neutrons as effectively as free water. Errors in core analysis result when gypsum is dehydrated prior to or during the analysis. Vacuum retort procedures used by many laboratories to determine fluid saturation and porosity effect a complete removal of water of crystallization from gypsum. The crystal water, distilled and collected with free water from the sample, is counted as water-sat11rated pore space. Dehydration of gypsum results in a decrease in volume occupied by calcium sulfate and a corresponding increase in pore volume. Thus, if gypsum is dehydrated by sample cleaning and drying procedures, subsequent porosity measurements with gas expansion or compression instruments will be high. The qualitative effect of gypsum on porosity determinations by retort procedures was discussed in a recent article by Bynum and Koepl3. They concluded that since false porosity was interpreted as being water saturated, determinations of oil content were not affected. Others in the industry, however, have pointed out that porosity values are often used with values of water saturation determined independently, e.g., from electric resistivity logs in making reserve estimates. Values of water saturation calculated from the formation resistivity using the Archie equation, S4= are actually low if values of are high due to gypsum. In this case, false porosity values due to gypsum could cause serious errors in calculations of oil-in-place. This investigation was made to determine quantitatively the effect of gypsum on porosity values determined by different core analysis procedures. EXPERIMENTAL PROCEDURES Dehydration of Gypsum The extent and rate of removal of water of crystallization from gypsum under conditions encountered in core analysis procedures were studied. Taken for the experiments were three types of relatively pure, naturally occurring gypsum, viz. selenite, satin spar and massive gypsum. Although all samples probably contained trace chemical impurities, each type lost the theoretical amount of water upon complete dehydration. An automatic recording thermobalance, similar to one described by Mauer2, was used to obtain dehydration rate data for samples heated in dry air. Water

By A. W. Ruff

In the last ten years large gains have been made in the field of blasting. These gains have been both in the theoretical and in the practical application of explosives. One of the most publicized changes in the practical application of commercial explosives is the now-prevalent use of ammonium nitrate and fuel oil. The new water-compatible mixture of ammonium nitrate and TNT should also have a large field of application. Most of the theoretical gains have been concerned with the actual rock breakage obtained with explosives. In the last ten years, large gains have been made in the field of blasting. These gains have been both in the theoretical and in the practical application of explosives. One of the most publicized changes in the practical application of commercial explosives is the now prevalent use of ammonium nitrate and fuel oil. The new water-compatible mixture of ammonium nitrate and TNT should also have a large field of application. Most of the theoretical gains have been concerned with the actual rock breakage obtained with explosives. EXPANDING-GAS-BUBBLE THEORY There has been an outstanding change in the conception of how an explosive produces rock failure. The early theory which explained rock breakage was correct for some of the first force-producing agents such as quicklime. When a drillhole was filled with quicklime and water added, the material expanded and steam was generated. The expanding material and the steam exerted a slowly increasing pressure on the sides of the drillhole. The force broke the rock by splitting. Because a great quantity of gas was produced by the deflagration of gunpowder, the same process of the gas pressure splitting the rock was assumed to take place. Even after 80 years of use, the rock-breaking action of all high explosives was thought to be caused entirely by the expanding gas bubble which tore and split the rock. Fig. 1 shows a vertical section through an exploding spherical charge of high explosive. It illustrates the early theory which attributed the entire breakage to the expanding gas bubble. The basic idea of this theory is that the breakage started at the explosive charge and progressed toward the free face. REFLECTED-WAVE THEORY me expanding-gas- bubble theory has gradually been replaced by the reflected-wave theory. The reflected-wave theory explains rock failure by explosives in the following manner: The enormously high gas pressure in the drillhole produces fracturing of the rock on the sides of the drillhole. The fracturing around a 1 1/2-in. diam drillhole is usually confined to an area with about a 6-in. diam. In the fractured area, the pressure of the gas is reduced until the force on the walls is no longer capable of fracturing the rock. Although the gas pressure does not continue to fracture the rock, the pressure imposes a high impact stress on the wall rock. In addition, a pressure or seismic pulse is produced in the rock. The pulse is probably entirely a compression pulse when originally produced in the rock. But, with distance, part of the energy of the compression pulse is transformed into a tension pulse which follows the compression pulse. The explosive charges and burdens used in conventional mine blasting are such that the tension pulse of the original wave is probably too small to be considered in a practical evaluation of the theory. The compression pulse is transmitted through the rock with no associated fracturing.

Jan 1, 1961

By R. N. Thurston, E. A. Nesbitt, G. Y. Chin

A general relalionship between the amount of glide shear (due to slip) and the macroscopic shape change has been developed. Since the deformation can be large, finite strain analysis is employed. In this treatnzent, the shape change is expressed by a deformation gradient matrix, F - [axi/aXj1, where X and x refer to the initial and final positions of a particle. This matrix is readily evaluated in terms of the amounl of glide shear, a , and the direction cosines of the slip-plane normal and the slip direction for a single active slip system. In the case of deformation from slip on several systems, the product F(a) of the several deformation gradient matrices is first calculated. Then, by assuming that the final configuration is reached by a long series of small shears of magnitude a, occurring more or less alternately in the several slip sys- IN problems of crystal plasticity, it is often necessary to relate the amount of glide in the operating slip systems to the macroscopic strain components. This relationship is relatively simple when only small strains are considered. In this case the separate strain contributions from several slip systems are additive. Such a procedure is incorrect in the case of large plastic deformation. To the authors' knowledge, no general treatment of the latter problem has appeared in the literature. In specific instances, Mark, Polanyi, and schmid3 have derived the relationship between glide and axial elongation during tensile pulling of a single crystal when only one slip system is active. A similar relationship for duplex slip was worked out by v. Goler and Sachs.4 Taylor and Elam5 have also studied in detail problems of large plastic deformation. Due to uncertainties as to the slip systems at the time, terns, the final deformation gradient matrix can be obtained. Mathematically, the problem is reduced to finding the limit of F(dN as N — m while a — 0 in such a way that the Product Na = 0, a ftnite conslant designatzng the accunzulated amount of shear. It turns out that this limit is simply , where F, is the matrix whose elements are the coefficients of a in the F(a) matix. Application is made of the present treatment to a fcc crystal of Perlrzalloy compressed on the (110) plane and contrained to elongate zn the [112] directzon. In addition, it is shown that one rnay readily obtain from the general analyszs the well-known formulas relating elongation, amount of glide shear, and amount of lattice rotation for crystals deforming by single and double slip under tension. however, they were mainly concerned with proving that slip occurs on {111}(110) systems in fcc metals. The present general treatment arose out of recent investigations of magnetic anisotropy in cold-worked Fe-Ni alloys6 as well as some related problems in strength anisotropy of single crystals.' Detailed application of the general analysis will be provided in the case of a Permalloy single crystal compressed on the (110) plane and constrained to elongate only in the [112] direction. It will be seen that, as expected, the small strain approximation leads to significant errors after moderate straining. It will also be shown that the present general treatment yields the formulas of Mark et al. and of v. Goler and Sachs in those specific cases. GENERAL CONSIDERATIONS Consider a homogeneous deformation in which a material point initially at moves to both positions being referred to the same set of Cartesian axes. Such a deformation can be

Jan 1, 1967

By C. E. Lundin, M. Hansen, D. J. McPherson

PRIOR work on the Zr-Cu phase diagram by Alli-bone and Sykes,' Pogodin, Shumova, and KUGU cheva,' and Raub and EngeL3 as confined largely to copper-rich alloys. The investigations of Raub and Engel were the most recent and seemingly the most complete of these. Alloys from 0 to 68.3 pct Zr were studied principally by thermal analysis and microscopic examination. These authors reported an inter metallic compound ZrCu, (1116°C melting point) and two eutectics, one at 86.3 pct Cu (977°C mp) and the other at 49 pct Cu (877°C mp). The solubility of zirconium in copper was reported to be less than 0.1 pct at 940°C. The zirconium melting stock consisted of Westing-house "Grade 3" iodide crystal bar (nominally 99.8 pct pure). It was treated by sand blasting and pickling (HF-HNO, solution) to remove the surface film of corrosion product, resulting from grade designation tests. The crystal bar was cold rolled to strip, lightly pickled again, and cut into pieces approximately 1/32 in. thick and 1/4 in. square. These were cleaned in acetone, dried, and stored for charging. The high-purity copper (spectrographic grade) was supplied by the American Smelting and Refining Co. with a nominal purity of 99.99 pct. These copper rods were rolled to strip, cut into squares the same size as the zirconium platelets, cleaned in acetone, dried, and stored. Equipment and Procedures The equipment used for melting and annealing the zirconium binary alloys and for the determination of solidus curves has been described in connection with previous work on the Ti-Si system' and in recent papers in this series describing the studies on eight binary zirconium systems.5-' Techniques employed for preparing and processing the alloys were also similar to those used in the above references. Ingots of 20 g were melted under a protective atmosphere of helium on water-cooled copper blocks in a nonconsumable electrode (tungsten) arc furnace. The ingots were homogenized and cold-worked prior to isothermal annealing to aid in the attainment of equilibrium. The specimens were heat-treated in Vycor bulbs sealed in vacuo or under argon, depending on the temperature of the anneal. Quenching was accomplished by breaking the Vycor bulbs under cold water. Temperature control was within ±3OC of reported temperatures. Thermal analysis was primarily relied on to determine eutectic levels, peritectic levels, and compound melting points. The induction furnace incipient melting technique was also used but did not provide the accuracy obtained by thermal analysis in this system, which involves much lower solidus temperatures than the other zirconium systems. A special technique for the determination of characteristic temperatures was employed in the case of several intermediate phases and their eutectics which displayed very small differences in melting temperatures. Specimens were sealed in Vycor bulbs and annealed at a series of very accurately controlled temperatures. Metallographic examination was then employed to reveal incipient melting. Furnaces and techniques in general were described previously.' The echant used was 20 pct HF plus 20 pct HNO3 in glycerine unless otherwise stated. Results and Discussion The chemical analyses of the majority of alloys prepared for the determination of phase relationships in this system are given in Table I and a brief summary of the equilibrium anneals employed is given in Table 11. In a preliminary program, alloys containing 1, 4, and 7 pct Cu were annealed for three different times at each of the temperatures 700°, 800°, and 900°C. No change in the relative amounts of phases present was detected after 350, 150, and 75 hr at the above temperatures, respectively. The times listed in Table II were accordingly chosen as a result of these preliminary tests. Zirconium-rich alloys containing from 0.1 to 10 pct CU were reduced by cold pressing from 58 to 8 pct, depending upon thk alloy content, homogenized for 7 hr at 900°C, and then reduced 80 to 13 pct by cold rolling, again depending upon copper content. Other alloys were studied in the cast, or cast and annealed conditions. The contracted scope of investigation for this system included the range 0 to 50 atomic pct Cu. This approximate region is shown in Fig. 1. Due to evidence of phase relationships departing considerably from those proposed by Raub and Engel" in the 50 to 100 atomic pct range, the investigation was extended to cover this composition area rather thoroughly also. Fig. 2 is a drawing of the entire diagram. The labeling of some phase fields was omitted in Fig. 2 for the sake of clarity. An expanded view of the zirconium-rich region, with the experimental points necessary for its construction, is given in Fig. 3. The generally accepted value of Vogel and Tonn8 or the allotropic transformation a + 862' ±5OC, was employed in the construction of these diagrams. A careful study revealed that the "Grade 3" crystal bar used in this investigation actually transforms over the approximate range 850" to 870°C, due to impurities. It must be expected that this two-phase field in unalloyed zirconium will cause some departures from binary ideality in the very dilute alloys. Zirconium-rich Alloys: The a + ß transformation temperature is decreased from 862" to about 822°C by increasing amounts of copper. Thus, a eutectoid reaction, fi ß a+ Zr,Cu, occurs at a composition of about 1.6 pct Cu. The eutectoid level was determined to lie between the alloy series annealed at 815" and 830°C. The placement of this eutectoid temperature

Jan 1, 1954

By R. I. Jaffee, H. R. Ogden, D. J. Maykuth

IN THE past year, Jaffee and Campbell&apos; and Finlay and Snyder2 reported on the mechanical properties of titanium-base alloys, some of which were in the same ranges of composition as are covered in this paper. In this paper, evidence confirming that given by Finlay and Snyder on the effects of carbon, oxygen, and nitrogen on titanium will be presented; and, in addition, new data will be given on the effects of these elements on the flow properties and phase transformation of titanium. Materials and Preparation of Alloys The preparation and general properties of iodide titanium have been adequately described elsewhere.&apos; , As-deposited iodide titanium rod, prepared at Battelle, of Vickers hardness less than 90 was employed as the base metal in the present work. This was the same material as that used by Finlay and Snyder.2 The probable analysis reported by them for standard quality metal holds here also: N 0.005 pct, 0 0.01 pct, C 0.03 pct, Fe <0.04 pct, A1 <0.05 pct, Si <0.03 pct, and Ti 99.85 pct. Carbon was added in the form of flake graphite supplied by the Joseph Dixon Crucible Co. Oxygen was added in the form of c.p. grade TiO, powder, produced by J. T. Baker Chemical Co. Nitrogen was added in Ti3N4 powder, supplied by the Remington Arms Co. Individual ingots weighed 7 or 8 g. Carbon, oxygen, or nitrogen was added by placing the corresponding powder in a capsule made from as-deposited iodide titanium rods and melting the capsule with the balance of the charge. The charge was are-melted with a tungsten electrode on a water-cooled copper hearth under a partial vacuum of very pure argon (99.92 pct minimum). Melting was practically contamination free. Vick-ers hardness increases of less than 10 points were normal for unalloyed iodide titanium control melts. Nitrogen analyses of are-melted iodide titanium showed a nitrogen content of 0.005 pct, about the same as is present in the as-deposited rod. No tungsten pickup was found in a melt of iodide titanium analyzed for tungsten. Weight losses in melting nitrogen-free alloys were very small and varied consistently from nil to 0.015 g (0 to 0.2 pct). This permitted the use of nominal composition for these alloys. Chemical analyses made for carbon, which can be analyzed conveniently by combustion methods, justified this procedure. Where nitrogen was added, considerable splattering took place. Here it was necessary to analyze for nitrogen by the Kjeldahl method. The ingots were hot rolled at 850°C to about 0.045 in. thick. After hot rolling, the strips were descaled by mechanical grinding, and then given a cold reduction of 5 to 10 pct to insure a uniform thickness throughout the length of the specimen. The edge strips and the tensile strips were annealed in a vacuum of 1x10-4 mm Hg pressure for 3 1/2 hr at 850°C and furnace cooled. Methods of Investigation Hardness Measurements: At least five Vickers hardness measurements were taken using a 10-kg load on each sample in the following conditions: (1) top and bottom of each ingot, (2) top and bottom surface of as-rolled and annealed sheet, and (3) on cross-section of annealed sheet and all quenched specimens. Tensile Tests: Tensile tests were conducted on Baldwin-Southwark testing machines having load ranges of 600 or 2000 lb. Tests were made on 1-in. gauge-length specimens, 3 1/4-in. overall length, 1/2 in. wide, 0.040 in. thick, with a reduced section 1 1/4 in. long and 0.250 in. wide. Two SR-4, A-7 strain gauges, one mounted on each side of the specimen, were used to measure the strain over a limited range to determine the modulus of elasticity. After the modulus of elasticity readings had been taken, load vs. strain readings were taken, using only one strain gauge, at increments of 0.0001 in. until the yield points were passed and then at 0.001-in. increments to the limit of the strain-gauge indicator (0.02 in.). Strain readings above 0.02 in. per in. were taken every 0.01 in., using dividers to measure the strain between the 1-in. gauge marks until the maximum load had been reached. Crosshead speed, when using the SR-4 gauges, was 0.005 in. per min, and, when using dividers, 0.01 in. per min. Flow Curves: Flow curves were determined using the true stress-true strain data obtained during the tension test. The usefulness of this type of information has been dealt with very adequately elsewhere by L. R. Jackson,&apos; J. H. Hollomon,6 and many others. Flow curves of true stress vs. true strain could be converted to the more conventional cold-work curve of 0.2 pct offset yield strength vs. percentage of cold reduction by means of the transformation, 1/1 = 1/1-R, where R is the fraction reduction in cold working. Thus, the true strains corresponding to percentage reduction can be calculated, and the 0.2 pct offset yield strengths scaled off the — 6 curve by taking the true stresses corresponding to the values of 6 + 0.002 strain. Heat Treatment: For the transformation studies, the alloys were heat treated in a horizontal-tube furnace using a dried 99.92 pct argon atmosphere, and quenched into water. Essentially no contamination was found after several hours of heat treatment at temperatures up to 1050°C. Metallography: Specimens were prepared in the

Jan 1, 1951

By J. P. Smith

Permian salt measures carry extensive lenses of soluble potash salts in north central Germany. Potash deposits of Oligocene age are found in the Upper Rhine Graben of Alsace (France), and in the Catalonian Basin of Spain. These deposits are found in a wide range of structural settings. Reserves are large, and the production of potash salts is an important phase in the economy of each of these countries.

Jan 1, 1950

A few years later another gazetteer said of Virginia: "The Ouasioto Mountains are 50 or 60 miles wide at the Gap. These mountains abound in coal, lime and free-stone." The Gap was the Potomac River. "Copper, iron, black-lead, coal, marble, limestone &c are found in this country."&apos; In the Morris papers, in Louisa and Goochland Counties, some records of operations in 1797 and 1798 have been preserved. These are: [ ]

Jan 1, 1942

By GEORGE W. HARHIS

IN the earlier period of anthracite-ruining, much coal was wasted, both underground and in the culm-banks on the surface. Such waste is common in the development of new mining districts, in which, as a rule, only the richest material can be profitably treated. In the anthracite-region, special causes operated to increase this evil. The mines were generally operated under 20-year leases, and royalties were paid upon such coal only as was actually marketed. The lessees consequently cared for immediate profit only. They were- not bound to win all the coal they exposed, or to leave it in such condition that their successors could win it. Nor was it their interest or duty to educate consumers in the use of their product. The market called for coal of large sizes ; and such coal they furnished, throwing away the rest. Any pains taken by them to bring about a more rational use of coal by their consumers would have borne fruit, after their leases had expired, to the benefit of somebody else. A full statement of the situation wits given in 1893, in the report of the State Commission, appointed in 1889 to investigate the subject.` That body included the names of Heber S. Thompson, William Griffith and the late Eckley B. Coxe.2 Its report gives special attention to the utilization of the old culm-banks.

Nov 1, 1905

By R. B. Moore

IN 1914 the writer and K. L. Kithil announced, through Bulletin 70 of the U. S. Bureau of Mines, that the United States possessed the largest deposits of radium-bearing ore in the world. At that time a small amount of this ore was being, mined and shipped to Europe, and one company was preparing to start the extraction and recovery of radium in this country. The importance of our carnotite deposits in Colorado and Utah up to the publication of Bulletin 70 was not, however, appreciated by anyone.. At that time the total supply of radium in the world was about 10 g., calculated as element, and when I estimated that at least 100 g. of radium element, and probably 200 g., would be produced from our carnotite deposits, there was a considerable amount of skepticism. Up to the present time almost 200 g. have come from this ore, and some writers put this figure a little higher. Uranium ore was found in the copper mines of the Union Minière du Haut-Katanga at Luiswishi in 1913. Later discoveries were made at other places in the Belgian Congo, and the Katanga ores now represent the largest supply of radium-bearing ore in the world. In fact, since 1923 very little radium has been produced from American carnotite, the Katanga ore representing practically the world&apos;s supply of. radium since that date.

Jan 1, 1930

By AIME

COAL, its acquisition and consumption, has loomed large enough in the lives of many of us at one time or another, not from a technical standpoint, perhaps, but on a utility basis, to keep the house warm and the plant going. The Chairman of the Coal Division was much like many of us in that respect until after his graduation from Northwestern in 1928. Then he went to work as geologist for the Zeigler Coal Co., investigating strip coal possibilities in western Illinois, and also did research in the microscopy of coal at the Illinois Geological Survey. His interest in coal was originated and stimulated by Gilbert H. Cady, of the Illinois Geological Survey. With his advice, and with the co-operation of M. M. Leighton, Survey chief, the results of his research work on the mineral constituents of coal at the Survey were accepted as a thesis for his doctorate which he received from Harvard in 1935. Nine days before the Christmas of 1906, Clayton Garrett Ball was born at Wauconda, Ill. His father was professor of geology at Northwestern until he retired in 1946; retirement didn&apos;t lessen his active interest in his profession; he&apos;s still teaching geology at the University of Kansas City. So it was only natural for Clayton to study at Northwestern. In 1937, following a year&apos;s connection with the Bell &

Jan 1, 1948

By Sherwin F. Kelly

Twenty five years of exploration has shown that the "geophysical dollar" is worth $1780 in the Orange Free State, $1488 on the Witwatersrand, $85 in Sweden, $28,000 in the Transvaal and $3500 or more in the U.S.

Jan 6, 1951

By P. A. Beck, M. V. Nevitt

All binary and a number of ternary u alloys formed by first long period transition elements were examined and found to be ferromagnetic at low temperatures. The Curie temperatures for these alloys were measured. It was found that the correlation of the Curie temperature with composition may be described qualitatively in terms of the contributions of the various component atomic moments to the saturation moment of the alloy. Ternary Fe-Cr-Mo u phase alloys were also found to be ferromagnetic, with a Curie temperature dependent on the iron content and largely independent of the unit cell dimensions. Similar relations were found for the Co-Fe-Cr and the Co-Cr-Mo a alloys, where the Co + Fe content appears to determine the Curie temperature. RECENTLY, it has become increasingly evident that the u phase is some kind of an "electron compound." Several papers1-&apos; discussed the empirical correlation between the composition of the various u phases in alloys of the transition elements and the distribution of electrons in the partially filled d-levels of the component atoms. However, a picture of the latter can be formed only in a more or less intuitive manner, as in the Pauling theory," and the rigorous treatment of these problems is at present prevented by lack of adequate knowledge of the electronic structure of the transition elements in the metallic state. It appeared reasonable to expect that investigation of the magnetic properties, which are related to d-shell electrons, may help in clarifying the physical nature of the foregoing empirical correlation. Qualitative tests of samples of various compositions have shown that certain u alloys become ferromagnetic at liquid nitrogen temperature." The present investigation was undertaken to determine whether or not low temperature ferromagnetism is characteristic of a large variety of u alloys and to establish how the Curie temperatures of ferromagnetic u alloys are influenced by changes in composition and in lattice parameter. In the first portion of the in- vestigation, Curie temperatures were measured for a series of u alloys containing either vanadium or chromium with one or two of the elements manganese, iron, cobalt, or nickel. In the second phase of the work, data were obtained on the Curie temperature of ternary (Fe, Co, Cr)a, (Fe, Cr, Mo)a, and (Co, Cr, MO)U alloys, as a function of composition and of interatomic spacing. Experimental Procedures High frequency vacuum melting in high purity re-crystallized alumina crucibles was employed in the preparation of the u alloys, using metals whose lot analyses are given in Table I. Approximately two-thirds of the alloys were analyzed chemically, the analytical results being in acceptable agreement with the intended compositions, as seen in Tables I1 and 111. The specimens were annealed for homogen-ization in an atmosphere of purified 92 pct He and 8 pct H, mixture or in evacuated and sealed Vycor tubes at temperatures from 780" to 1300°C, depending on the temperature range of the u phase field for the particular composition. The annealing temwerature and time for kach alloy are given in Tables 11 and 111. Curie points were determined by an induction method; the change with temperature of mutual inductance between two coils was observed when the i-u specimen was inserted into the flux path between the coils. The transformer consisted of three coils each containing 1200 turns of 0.0050 in. diam enameled copper wire. The center coil, P in Fig. 1, served as the primary coil, and was linked magnetically with each of the two secondary coils, S, and S? which were connected in series opposition. The primary coil, P, was energized by an audio-oscillator, set at a frequency of 500 cycles per sec, while the signal from the transformer secondary circuit,

Jan 1, 1956

By Walter Gaby

L. C. GRATON, Cambridge, Mass.-May I ask, in connection with one point in the summary, to what extent the author regards actinolite equivalent to tourmaline as an index of high-temperature and presumably magmatic conditions of deposition of the accompanying sulphides? W. E. GARY.-I merely advanced the idea that the mineral actinolite might have some such significance. In the copper deposit at Braden in South America, the ore occurs in an andesite breccia which is cemented by a matrix of sulphides, quartz, and tourmaline. Tourmaline is a high-temperature mineral, and when we find it associated with ores, these are regarded as having come from a volcanic or deep-seated source, hence a primary hypogenetic deposit. Thus we can count on greater continuation of the ore with depth than in some other kinds of deposit, and I thought that the actinolite, being also a high-temperature mineral, might have some such bearing in the case of Mount Morgan. I did not advance this idea as a final conclusion from a study of such phenomena, but thought that it might bear some discussion in view of the fact of the peculiar occurrence of this mineral in a notable orebody. It also occurs with the copper ores at Ducktown, Tenn., and in both cases may only be due to general regional metamorphism.

Jan 12, 1916