Search Documents

By Harry H. Angst, Reuel A. Cochrane

THE successful exploitation by opencut methods of the low-grade porphyry copper deposits is due to the economical handling of large tonnages. Large tonnages are possible only if the rock material is broken so that the large power shovels can operate with minimum delays. This is particularly true at the New Cornelia mine, where the dense, hard, tough rock material creates problems not encountered in most of the porphyry copper mines. The introduction of churn drills at the New Cornelia for primary drilling, in 1936, necessitated a complete change in the methods of breaking ground as formerly air drills had been used. The blasting operations are of particular interest because of the handling of great quantities of high explosives in safely and efficiently fragmenting the hard rock material. ROCK FORMATIONS At the New Cornelia mine the rocks are quartz monzonite with a diorite border facies intruding a rhyolitic series. Overlying these formations is a fanglomerate formation composed of boulders of monzonite, diorite, rhyolite, and other types of rock of unknown derivation. (The word "fanglomerate" is used in this paper in referring to the local conglomerate type of rock formations.) The ore body is approximately 4800 ft. long and 2800 ft. wide, and is of the disseminated type. Mineralization occurs principally the quartz monzonite and to some extent in the adjacent diorite and rhyolite. The principal ore minerals are chalcopyrite, bornite, and a small amount of chalcocite. Over a considerable area the quartz monzonite is extremely hard and siliceous in character, owing to pegmatitic zones of alteration. The hardness of the ground depends on the intensity of the silicification. In a small area in-the pit, the monzonite contains an abundance of pyrite accompanied by sericitization and is soft and easily fragmented. This is true also in the remaining oxidized portion of the ore body. The diorite and rhyolite formations, like the monzonite, vary from extremely hard to very soft material, but on the whole are easier to fragment than the monzonite. jointing is prevalent in all the rock formations and plays an important role in the blasting efficiencies. In the fanglomerate formation, numerous well-defined joints, widely spaced, tend to make the ground blocky when blasted. This is a deterrent to good fragmentation. In the other rocks the joints are more numerous and are closely spaced, except in localized areas where the formations are extremely hard. These descriptions indicate that the lowest blasting efficiency will be obtained in the harder formations, from which the major portion of the mine production is obtained; namely, the monzonite and rhyolite. All rock formations mined at the New Cornelia pit are so hard that excavation

Jan 1, 1941

By J. Doig, A. A. Bauer, F. A. Rough

AN investigation of the phase relationships between the 6 phases of the uranium-molybdenum and uranium-titanium systems was conducted by studying alloys ranging in composition from uranium-31.5 at. pct Mo to uranium-34 at. pct Ti. A ternary cut showing these phase relationships is presented upon the basis of thermal-analysis data obtained and upon the basis of metallographic and X-ray examination of heat-treated and quenched specimens. Isothermal ternary sections, inferred from phase relationships determined between the two 6 phases, are presented for the uranium-molybdenum-titanium system. In the compositional range investigated, a y-ura-nium solid solution exists at elevated temperatures. At about 900°C the 6-U2Ti phase, with limited molybdenum solubility, forms. Epsilon, a molybdenum-titanium-rich solid solution appears at the same temperature and appears in all phase regions that exist below this temperature except in the terminal 6-phase regions. The y phase is stable to approximately 660°C in titanium-rich alloys; the y and 6-U,Ti phases decompose at this temperature to a uranium in a peritectoid reaction. The y phase in molybdenum-rich alloys of the ternary cut studied decomposes in an apparent eutectoid reaction, at about 593°C, to the 6-uranium-molyb-denum and a-uranium phases. The e phase while present, presumably plays a negligible role in these reactions. Titanium was found to markedly decrease the stability of retained y in these alloys. Age-hardening characteristics developed in titanium-contain ing uranium-molybdenum alloys quenched from 900°C and aged at 500°C are ascribed to decomposition of Y to the a and E phases. INTRODUCTION Alloys of uranium with molybdenum, titanium, and zirconium, respectively, are of great interest because of their potential use as reactor fuels. As a result, this interest extends to the constitution of these alloys, particularly in view of their uniqueness of constitution. In these systems, alone, among known uranium-alloy systems, an intermediate phase forms by direct decomposition of the high-temperature y-uranium phase. As a prelude to possible future alloy development, an investigation has been undertaken of the phase relationships that occur between the intermediate phases of these systems. These phase relationships have already been reported for the intermediate 6 phases of the uranium-zirconium and uranium-titanium systems.' The results of an investigation of the phase relationships between the 6 phases of the uranium-molybdenum and uranium-titanium systems are reported here. The phase relationships that occur in the binary systems pertinent to this investigation are shown in Fig. 1. Phase nomenclature appearing throughout this report is as shown in these diagrams; the crystal structure of the phase is given in Table I. EXPERIMENTAL PROCEDURE Alloys were cast and fabricated to flat plate. Specimens were heat treated and examined metal-

Jan 1, 1959

By J. T. Eash, N. B. Pilling

As a group, the alloys of iron, nickel and carbon are, in application, one of the most versatile of the ferrous alloy family, and while many investigations have been made of their properties and structure only a few attempts have been made to show the microstructural relation over a wide range of composition. It is neccssary at once to be clear about the kind of structural relation with which we are concerned. The equilibrium diagram provides quantitative data regarding structural make-up and its variation with temperature, but equilibrium structures often are far different from the technologically significant ones. This is particularly true of steels and cast irons, and some of the most important cornponents of their structure may have no place in the diagram of equilibrium. The fugitive phases that result from transFormation are dealt with in a highly detailed and descriptive manner in. the S-curves originated by Bain. The present effort lies in a still different field, which is to portray the relation between sweeping changes in composition and in resultant structure, under controlled but nonequilib-rium conditions of thermal treatment. The Guilletl diagram presented in 1903 was the initial attempt at such a correlation and frequent references to this diagram can be found in the literature even though later work has shown it to require considerable modification. Kase2 published in 1925 a diagram that was based upon observations of furnace-cooled melts: At low carbon contents this diagram agreed fairly well with experience in showing pearlite to exist in alloys containing up to 6 per cent nickel, and completely austenitic steels at 24 to 28 per cent nickel. At high carbon contents, however, irons were indicated as being martensitic at around 2 per cent nickel and austenitic at 12 per cent nickel; these interpretations are open to serious question. Based upon experience with steels and cast iron, Wickenden3 suggested a diagram that agreed fairly well with Kase's in the steel range but which presented a wide departure from it in the higher-carbon, high-nickel regions. In its broad picture, the Wickenden diagram is an approach to "practical" structures. Reference may be made at this point to the efforts of Marsh5 to construct an iron-nickel-carbon equilibrium diagram by the coordination of scattered data, which are described at length in the monograph cited. None of these preceding attempts has appeared to meet the need for an exposition of the structural sequence that is encountered in traversing the nickel-steel nickel-cast-iron range under what might be called ordinary departures from equilibrium. ExperimentaT. Conditions Since the intent has been to establish structures developed under arbitrary conditions, experimental details have perhaps more than usual importance. Three of these conditions should particularly be noticed: (I) the material was cast and not subjected

Jan 1, 1942

By J. T. Eash, N. B. Pilling

As a group, the alloys of iron, nickel and carbon are, in application, one of the most versatile of the ferrous alloy family, and while many investigations have been made of their properties and structure only a few attempts have been made to show the microstructural relation over a wide range of composition. It is neccssary at once to be clear about the kind of structural relation with which we are concerned. The equilibrium diagram provides quantitative data regarding structural make-up and its variation with temperature, but equilibrium structures often are far different from the technologically significant ones. This is particularly true of steels and cast irons, and some of the most important cornponents of their structure may have no place in the diagram of equilibrium. The fugitive phases that result from transFormation are dealt with in a highly detailed and descriptive manner in. the S-curves originated by Bain. The present effort lies in a still different field, which is to portray the relation between sweeping changes in composition and in resultant structure, under controlled but nonequilib-rium conditions of thermal treatment. The Guilletl diagram presented in 1903 was the initial attempt at such a correlation and frequent references to this diagram can be found in the literature even though later work has shown it to require considerable modification. Kase2 published in 1925 a diagram that was based upon observations of furnace-cooled melts: At low carbon contents this diagram agreed fairly well with experience in showing pearlite to exist in alloys containing up to 6 per cent nickel, and completely austenitic steels at 24 to 28 per cent nickel. At high carbon contents, however, irons were indicated as being martensitic at around 2 per cent nickel and austenitic at 12 per cent nickel; these interpretations are open to serious question. Based upon experience with steels and cast iron, Wickenden3 suggested a diagram that agreed fairly well with Kase's in the steel range but which presented a wide departure from it in the higher-carbon, high-nickel regions. In its broad picture, the Wickenden diagram is an approach to "practical" structures. Reference may be made at this point to the efforts of Marsh5 to construct an iron-nickel-carbon equilibrium diagram by the coordination of scattered data, which are described at length in the monograph cited. None of these preceding attempts has appeared to meet the need for an exposition of the structural sequence that is encountered in traversing the nickel-steel nickel-cast-iron range under what might be called ordinary departures from equilibrium. ExperimentaT. Conditions Since the intent has been to establish structures developed under arbitrary conditions, experimental details have perhaps more than usual importance. Three of these conditions should particularly be noticed: (I) the material was cast and not subjected

Jan 1, 1942

West Virginia University, Engineering Experiment Station, Morgantown, W Va C E Lawall, Director. For copies of Bulletins or other information address the Director Two classes of the Bulletins published by the Engineering Experiment Station are of particular interest in this directory- Research Bulletins, and Extension Bulletins, or bulletins published for use in extension work They are. Research Bulletin 1, The conservation of natural gas in West Virginia (1918), 2, Acceleration stresses in hoisting ropes (1927), 3, Classification of gas wells for operation (1927), 4, Mining methods in West Virginia (1929), 5, The whiteware industry of West Virginia, Extension Bulletin 1, Electricity in mines, series

Jan 1, 1933

By Thomas O. Breitling

The Mill Design Session at the Annual Meeting in New York next February will have a total of four papers. All of these papers will be concerned with the subject of in-plant dust in the hard-rock mining industry. The emphasis on efficient dust collection is timely, because dust is a problem not yet adequately covered in AIME papers. In general, dust collection should be the step following dust suppression. Dust collection and its return to the ore recovery circuit, or its waste to tailing are sources of added operating cost. If possible, dust should be kept in the main stream of ore flow by suppression.

Jan 1, 1970

By Freeman Bishop

The House Ways and Means Committee recently heard a bitter dispute over whether gasoline with lead is a worse pollutant than gasoline without lead. The lead industry is also squarely in the middle of this dispute for obvious reasons. Lead used in gasoline amounts to 270,000 tpy, or more than 254 of the annual total mined in the U.S. Few industries can face the loss of such a market without wondering how they are to stay in business. The lead industry picked up unexpected support in this dispute, however, when the AFL-CIO stepped up with outright opposition to the President's proposal to tax lead in gasoline.

Jan 1, 1970

ENGINEERS AVAILABLE (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) A member of the Institute who has had many years' experience in office management for prominent mining engineering and metallurgical companies, and who is now located in the West, would like to secure an executive position with a firm or company engaged in mining or metallurgy, located in the East, and preferably in New York. No. 139. Member, aged 36, married, graduate mining engineer, 14 years' active experience as engineer, superintendent, and manager of large coal-mining operations. Wide experience in development and operation of

Jan 10, 1914

By Joseph W. Leonard

In a recent publication in the SME Transactions of September, 1975, Volume 258, entitled “Potential for Further Lowering Sulfur in Intensively Cleaned Coal at Mines,” the writer discussed: (1) technical findings useful for the management of reserves to further lower sulfur in intensively cleaned coal and (2) a future coal preparation plant concept for the intensive cleaning of sulfur. The purpose of this technical note is to (1) illustrate the nomographs that can be formed when recovery is phased in with previous work, (2) make note of the powerful potential for predicting future cleaning performance in unmined areas, and (3) discuss resulting mathematical interrelationships.

Jan 1, 1979

By Joseph W. Leonard

In a recent publication in the SME Transactions of September, 1975, Volume 258, entitled "Potential for Further Lowering Sulfur in Intensively Cleaned Coal at Mines", the writer discussed: (1) technical findings useful for the management of reserves to further lower sulfur in intensively cleaned coal, and (2) a future coal preparation plant concept for the intensive cleaning of sulfur. The purpose of this technical note is to ( I ) illustrate the nomographs that can be formed when recovery is phased in with previous work, (2) make note of the powerful potential for predicting future cleaning performance in unmined areas, and (3) discuss resulting mathematical interrelationships.

Jan 1, 1978

By Murray F. Hawkins, Marion L. Kimmel

sage' appears to have been the first (1933) to design a rolling ball viscosimeter for the express purpose of measuring the viscosity of oils with natural gas in solution, i.e., under reservoir conditions. In 1940 Hocott and Buckley' further refined the rolling ball instrument in both design and method of operation, and their instrument, known as the Humble type, was the forerunner of present day viscosimeters used in petroleum production and research laboratories. They also initiated the technique of charging the viscosimeter with a sample directly from a bottom hole sampler. In 1948 the committee on engineering research 01 the Petroleum Division of the AIME in Part 3 (1) of

Jan 1, 1955

By Fred W. Shultz

The process engineer is familiar with the in any methods employed in the past for analyzing various materials. These include panning. eyeballing, and wet chemistry. Of those mentioned only wet chemistry has been and will continue to be a standard measure for the elemental content in a given material. However, wet chemistry, by the very nature of the method, can be excessively time-consuming and thus reducing obviously the number of samples that may be processed in a given period. The analysis by X-ray, in most cases, requires nothing more than assurance that the sample is in a suitable state for presentation to the X-ray spectrometer.

Jan 1, 1964

By Harry A. Perry

The Highlad underground uranium mine is located in the southern Powder River Basin, Converse County, Wyoming. Development by Exxon Minerals Company began in 1973 and average production from the complex roll- front deposit ranges from 500 to 600 stpd. A staff of six eight grade control technicians work within the Geology Department to guide and monitor production, to minimize waste and to account production to reserve estimates. A thorough knowledge of the complex roll- front deposit aids in accounting production to reserve estimates. Grade control technicians assist the mine geologist in making geologic cross sections, in estimating reserves, and in predicting monthly and quarterly production grades.

Jan 1, 1980

By Oliver Bowles

WHEN a new type of equipment revolutionizes methods of quarrying one kind of stone, producers of other kinds focus their attention on its potentialities in their particular fields. The purpose of this paper is to discuss the accomplishments of the wire saw in slate, to show its more limited attainments in other kinds of stone, and to point out the possibili-ties of much wider application. A wire saw consists of a 3/16-in. or 1/4-in. three-strand wire cable that runs as a belt and cuts the rock by abrasion. (Fig. 1.) The teeth of the saw are sand grains carried in the grooves between the strands.

Jan 1, 1936

By A. A. Dor

Out of nine new major iron ore concentrators put in operation during the last three years, or expected to be commissioned in 1968, seven incorporate primary grinding mills and have a total design capacity of 13,150,000 ltpy of pellets, while only two include conventional rod and ball mill grinding circuits for a total design capacity of about 6,100,000 ltpy (Table I). This evolution in the application of primary grinding to hard, fine grained magnetite ores represents an important development in the technology of mineral processing. It has been the outcome of comprehensive testwork in the laboratory and in pilot plants.

Jan 11, 1968

By Joseph R. Hatch

When compared to average shale composition, average coal is enriched in sulfur and selenium, has similar amounts of arsenic, beryllium, lead, antimony and molybdenum, and is depleted in at least 26 other elements. Within a coalfield, or region, some coals are enriched (10X average shale) in silver, arsenic, cadmium, cobalt, germanium, molybdenum, nickel, lead, selenium, uranium, and zinc. Important factors controlling element distributions in coal include geochemical conditions (primarily pH) in the peat swamp, composition and depositional environment of coal roof rocks, thermal maturity (rank), nature and intensity of any epigenetic mineralization, composition of ground waters that come in contact with the coal, and degree of weathering.

Jan 1, 1983

By C. H. Li, R. J. Stokes, T. L. Johnston

Sodium chloride crystals are brittle in the presence of surface microcracks. Water immersion leads to an enhancement of ductility which is retained indefinitely in dry air providing the crystal is dried without leaving a surface precipitate. Storage in a damp atmosphere results in a surface reaction and consequent rembrittlement. Although elimination of surface flaws in ionic solids does not necessarily enhance ductility, there is always a change in the location of the fracture origin. EVER since the original experiments of Joffel there has been controversy over their interpretation and no satisfactory generalized explanation has yet been given. It is generally admitted that when sodium

Jan 1, 1961

By A. Blake Caldwell

Northwest frontier is here defined as Alaska, the Yukon, the Northwest Territories and northern British Columbia. The mineral potential of this area is great and will unfold in the decade ahead but now the largest single producer is the Pine Point lead-zinc mine in the NWT about 1200 km north of Edmonton, Alta., close to the south shore of Great Slave Lake. The mill, initially designed for 4540 mtpd, was expanded to 7250 mtpd in 1969. This operation is described in detail in Mining and Concentrating of Lead and Zinc, Vol.1, Chapt. 17, SME/AIME in the article by W. H. R. Gibney.

Jan 1, 1971

By C. H. Johnson

THE year 1952 has seen the continuance of the trend pointed out by Tell Ertl in this magazine a year ago, toward mechanization in metal and mineral mines. Outstanding progress has been made in the adoption of rock bolting in situations where, a short time ago it would have seemed inapplicable. New devices, better equipment, and improved practices are in part responsible for shifting fashions in mine development, stoping methods, and transportation systems. Only new mines, of course, can take the advantage of the new ideas that are being tested and demonstrated throughout the industry, but the old mines often show a surprising adaptability

Jan 2, 1953

By H. D. Newell

THERE has been much research and commercial development in recent years in the use of chromium and nickel in steels of various types, including those intended for high-temperature service. By "high-tem-perature steels" are meant those specifically designed for service at ele-vated temperatures in steam plants, oil refineries and other industries where high-temperature operations are conducted. This paper is devoted to some preliminary data on the effect of silicon on certain of the most popular chromium-molybdenum steels now being used in quantity by the refining industry and includes a short statement on the influence of copper in steels intended for high-temperature service.

Jan 1, 1937