Search Documents

By W. A. Backofen, G. Y. Chin, W. F. Hosford

The effect of machine stiffness on discontinuous flow and fracture of the 2024 aluminum alloy was studied in tension at 4.2OK. An increase of machine stiffness was found to decrease the amount of elongation and drop in load during discontinuous flow, thereby postponing fracture to larger strains and higher stresses. The possibility of utilizing stiffened tools in deformation processing to suppress shear fracture originating from unstable flow was indicated. The problem of nucleating discontinuous flow and the role of the effective mass of the system in discontinuous flow were also considered. AT low temperatures the plastic flow of metals is often discontinuous, with sudden load drops and elongations.1,3 Basinski1,4 has presented strong evidence that discontinuous flow, at least in aluminum alloys, occurs under nearly adiabatic conditions. During testing the load may drop suddenly and flow become localized when the thermal softening, due to heat generated in plastic straining, is greater than the strain and strain-rate hardening. This instability criterion is more easily satisfied at low temperatures because 1) the volume specific heat is reduced so that relatively large temperature increases are possible in straining, and 2) the flow stress is relatively temperature-dependent. The important role of adiabatic shear in ductile fracture processes has been emphasized,5-1 and consideration has already been given to the influences of thermal and mechanical properties on the tendency of a material to undergo adiabatic shear.17677 By focusing attention on how the mechanical loading system influences low-temperature discontinuous flow, additional insight into adiabatic shear and its effect on fracture may be gained. EXPERIMENTAL PROCEDURE Because of its low thermal conductivity, the 2024 aluminum alloy exhibits a highly consistent discon- tinuous-flow behavior at 4.2°K and was therefore chosen as the material for study. Machined specimens of 0.113 in. diam and 1.125 in. gage length were solution heat-treated at 490°C for 3 hr, quenched into cold water, and immediately immersed in liquid nitrogen until just before testing. Testing was done at 4.2°K by immersion in liquid helium at a crosshead drive rate of 0.03 in. per min. As normally used (hard-machine basis), the spring constant of the testing machine was k = 25,000 lb per in. By inserting beam springs in series with the specimen, this value could be lowered by a factor of about 100. Details can be found elsewhere.? As a result of variable machine stiffness, the actual strain rate ranged from about 3 x 10 5 to 3 x 10-4 per sec from one test to another, as well as within any one test. However, preliminary tests had established that the tensile curves were not altered significantly by this strain-rate variation. Fig. 1 shows a typical load vs plastic-elongation curve for a solution heat-treated 2024 aluminum alloy specimen pulled in the standard hard machine (k = 25,000 lb per in.) at 4.2"K. The elastic extension has been subtracted. Plastic flow proceeded smoothly from yielding at approximately 22,000 psi (load = 220 lb) to a strain of about 4 pct at which point the flow became discontinuous. The magnitude of the load drops as well as the plastic elongation per drop increased with increasing strain until the specimen finally broke abruptly. The load-elongation behavior of a sample tested with a relatively soft machine under otherwise identical conditions is given in Fig. 2. In general, there

Jan 1, 1964

By M. King Hubbert, David G. Willis

A theoretical examination of the fracturing of rocks by means of pressure applied in boreholes leads to the conclusion that, regardless of whether the fracturing fluid be of the penetrating or non-penetrating type, the fractures produced should be approximately perpendicular to the axis of least stress. The general state of stress underground is that in which the three principal stresses are unequal. For tectonically relaxed areas characterized by normal faulting, the least stress should be horizontal; the fractures produced should be vertical with the injection pressure less than that of the overburden. In areas of active tectonic compression, the least stress should be vertical and equal to the pressure of the overburden; the fractures should be horizontal with injection pressures equal to or greater than the pressure of the overburden. Horizontal fractures cannot be produced by hydraulic pressures less than the total pressure of the overburden. These conclusions are compatible with field experience in fracturing and with the results of laboratory experimentation. INTRODUCTION The hydraulic-fracturing technique of well stimulation is one of the major developments in petroleum engineering of the last decade. The technique was introduced to the petroleum industry in a paper by J. B. Clark,' of the Stanolind Oil and Gas Co. in 1948, and since then its use has progressively expanded so that by the end of 1955 more than 100,000 individual treatments had been performed. The technique itself is mechanically related to three other phenomena concerning which ah extensive literature had previously developed. These are: (1) pressure parting in water injection wells in secondary-recovery operations, (2) lost circulation during drilling, and (3) the breakdown of formations during squeeze-cementing operations, all of which appear to involve the formation of open fractures by pressure applied in a wellbore. The most popular interpretation of this mechanism has been that the pressure had parted the formation along a bedding plane and lifted the overburden, notwithstanding the fact that in the great majority of cases where pressures were known they were significantly less than those due to the total weight of the overburden as determined from its density. Prior to 1948, this prevalent opinion had already been queried by Dickey and Andresen,2 in a study of pressure parting; and by Walker,"' who, in studies of squeeze cementing, pointed out that the pressures required were mostly less than those of the overburden, and inferred that the fractures should be vertical. J. B. Clark,' in his paper introducing hydraulic fracturing, and later Howard and Fast," and Scott, Bearden, and Howard," also of Stanolind, postulated that the entire weight of the overburden need not be lifted in producing horizontal fractures, but that it was only necessary to- lift an "effective overburden," requiring a correspondingly lower pressure. Hubbert,7 in discussing the paper by Scott and associates, pointed out that the normal state of stress underground is one of unequal principal stresses; and in tectonically relaxed areas, characterized by normal faults, the least stress should be horizontal. Therefore, in most cases, fracturing should be possible with pressure less than that of the overburden and, moreover, such fractures should be vertical. Harrison, Kieschnick, and McGuire,8 also on the expectation that the least principal stress should be horizontal, argued strongly in favor of vertical fracturing. Scott, Bearden, and Howard6 observed that, when

Jan 1, 1958

By T. D. Murphy

The element silicon, with its usual partner, oxygen, plays the same role on this planet relative to inorganic materials as carbon and hydrogen play with respect to living organisms. The crystallographic structure of silicon dioxide (SiO,) consists of one atom of silicon well-nigh inseparably bonded to four contiguous atoms of oxygen, a gas of but slightly more than half its atomic weight, forming a three-dimensional network of SiO, tetrahedra (Dietz, 1968). This wispy arrangement is the fabric of the mineral quartz which is one of the harder, more abrasive, and chemically stable raw materials to be found in Mother Nature's cupboard. Most of us are vaguely familiar with the observation that nearly 60% of the lithosphere to an approximate depth of 10 miles is composed of these two elements, which proportion actually rises to about 75% if the atmosphere, hydrosphere, and biosphere are included (Parker, 1967). Elemental silicon is a brittle steel-gray metalloid with a density of 2.42 and does not occur in nature. In its limited commercial form, which is still brittle and metallic in appearance, its density drops to 2.33. It combines with oxygen to form the gaseous oxide SiO, or the solid dioxide SiO, (analogous to its congener carbon in CO and CO,); a tetrachloride SiCl, (analogous to CC1,); or, combining with oxygen and one or more metal ions, forms the largest rock-making family of all, the silicates. Further, next to the feldspars, quartz is the most abundant known mineral and, in some form or another, accounts for roughly 12% of surficial terrestrial rock. It is this so-called "free silica" to which your attention is chiefly directed in this chapter. In any such consideration of silica, its several crystalline phases with their attendant differing physical properties appear worthy of delineation. Alpha quartz is the only one of this interesting polymorphic family that is thermodynamically stable at normal pressures and temperatures up to about 573°C. The low phases of tridymite and cristobalite can exist in the so-called metastable state below 117°- 200°C but seldom occur in nature in these two different crystal forms (Sosman, 1965). Opaline silica, now considered by most researchers to be a variety of cristobalite, occurs in abundance and is the only exception. The three remaining polymorphs, keatite, coesite, and stishovite, also are metastable under ambient conditions. Keatite, however, is not known to occur naturally and has only been synthesized in the laboratory. The other two have been identified in submicron sizes and in microscopic amounts, occurring naturally as a result of high order shock-wave pressures generating quite elevated temperatures-such as might accompany the impact of a large meteorite on a hard sandstone terrain (Chao, et al., 1962). An intriguing characteristic of these silica minerals, and one which has very practical applications, is their extremely variable densities. The classic 2.65 specific gravity of alpha quartz drops to 2.20 in tridymite, cristobalite, and lechatelierite (natural silica glass), as well as in many man-made glasses of commerce which are merely noncrystalline or amorphous solids in the form of super-cooled liquids which can no longer change their shapes (Pauling, 1950). It rises again to 2.50 and 2.93 for keatite and coesite, respectively, and finally becomes a reported 4.35 for stishovite-nearly a 50% range in density for the known physical combinations that silica naturally assumes (Frondel, 1962; Konnert, et al., 1973; Pecora, 1960).

Jan 1, 1975

By K. C. Strebig, C. W. Schultz, A. A. Selim

The effect of some organic additives in diamond drilling of quartzite was investigated in the laboratory. The drill was designed to measure the rate of penetration, the thrust, and the torque and to record each as a function of the distance drilled. A statistical plan was followed throughout the investigation and an equation representing the bit performance was derived from the mathematical theory of reliability. The drilling torque was found to increase with the use of additives while the sliding coefficient of friction and the wear coefficient decreased. The energy per unit volume consumed was found to increase with the use of additives. A hypothesis explaining the effects achieved with the additives is given. INTRODUCTION For some time researchers have attempted to increase drilling efficiency by adding certain agents to the flushing medium. Much of this interest is the result of the observations of Rehbinder, Shreiner and Zhigach1 They postulated that "...in processes for the mechanical destruction of solids, a region of increased crack formation is created in the deformed layers adjoining that surface of destruction, forming the predestmction zone. The surrounding medium (for example, a liquid) which wets a given solid will penetrate the embryo microcracks of the predestruc-tion zone. Increasing the molecular affinity of this liquid for the surface of the solid considerably facilitates the deformation and destruction by softening the solid in the zone of increased crack formation. In this manner, the hardness or strength of the deformed body is decreased by the influence of the penetration of the liquid into the predestraction zone." This is known as the "Rehbinder effect". Rehbinder's work has prompted many investigators to examine the effect of additives on the mechanical destruction of rocks. Engelmann, Terichow and Selim reported that the maximum penetration of the rock by a diamond point in a solution environment was at the isoelectric point of the solution.* Robinson reported that his results did not appear to support the theory of Rehbinder.3 Joris and .McLaren suggested that additives with surface tension lower than water will be more efficient in cooling the diamonds.4 Their effectiveness in removing the fine cuttings from the face of the bit will also improve the efficiency of the system. They reported an improvement in impregnated bit life and penetration rates with the use of soluble oil additives. In contrast, Long and Agnew, drilling with surface set bits, reported that lubricating agents increase bit temperature and wear.5 A significant change was reported6 in the mechanical properties of rock with polar additives. It was concluded that this change in the mechanical properties of the rock in the presence of the additive is due to the rock hydrophilic properties. Ethylene glycol, glycerine and anionic detergent were selected for this investigation because their surface tension is lower than that of water. The surface tension of these additives for the concentrations studied was 42 to 75 percent of the surface tension of water. A low surface tension additive would wet the surface of the diamonds more easily and hence would be more effective in cooling the diamonds. Another characteristic of these low surface tension additives is their effectiveness in removing the cuttings and preventing the flocculation of the formed particles in the drilling process. This article summarizes the results of an investigation performed at the laboratories of USBM, Twin Cities Mining Research Center. The objective of the investigation was to study the over-all effects of some organic additives on the performance of diamond impregnated bits in atmospheric drilling conditions only and not in downhole pressured conditions.

Jan 1, 1970

By E. A. Has, E. Mcl. Tittmann

Double roasting of sinter carrying a high percentage of lead concentrates, gave rise to the problem of removing the sheets of metallic lead formed in the wind boxes. The solution of the problem has been found in the water sealed wind boxes. The metallic lead is granulated and can be removed without seriously interfering with the operation of the machine and eliminates necessity of men going in wind boxes with air guns. THE practice of double sintering the charge for lead blast furnaces, which is now standard throughout the lead smelting industry, has introduced the rather difficult problem of cleaning the wind boxes on sintering machines used for the final pass. Two factors have more recently accentuated this problem: (1) the growing demand of workmen for better working conditions and less arduous labor, and (2) the growing dearth of crude lead ores and the improved grade of lead concentrates demand a charge carrying the maximum percentage of lead. One to 2 pct of such high lead charges (30 to 40) when processed on machines in reasonably good condition will pass through the grates and report in the wind boxes. One-half to three-quarters of this material will be metallic lead reduced by the coke breeze or other fuel mixed with the charge. This lead forms large cakes or chunks which are hard to remove and which substantially increase the time the machine is out of operation for cleaning the wind boxes. A high lead fall can reduce the operating time 30 pct. As a specific example, a 30 ft machine having 63 in. pallets, and equipped with three conventional wind boxes, requires 3 to 4 hr per day for removing the accumulation in the wind boxes when operated as a final pass machine. This same machine when operated on raw charge requires less than an hour per day for cleaning. To eliminate formation of large chunks of lead in the wind boxes of the final pass machines and time lost in cleaning the boxes, R. C. Rutherford of the Chihuahua smelter of the American Smelting and Refining Co., devised and patented* a wind box having a water bath to granulate the lead as it falls from the grate bars. Later, C. H. Harris of the San Luis plant made and patentedt an improvement on Rutherford's device in which the water bath seals the wind box in a manner permitting the latter to be readily cleaned without destroying the vacuum. The first machine to our knowledge to use the water bath box was at the Chihuahua plant along the lines of the Rutherford patent. In 1942, a machine was placed in operation at the El Paso plant which incorporated the features of both Rutherford and Harris. This machine is 40 ft long equipped with pallets 63 x 24 in., and having 4 wind boxes 10 ft 4 in. x 7 ft 2 in. x 51 ft 3 in. in size (fig. 1). The air from the fourth box is returned to the first three, and the gas from the first three discharged to a baghouse. The machine has conventional drive, discharge hopper,

Jan 1, 1951

Agnico-Eagle Mines Ltd. comprises a Gold Division at Joutel, Quebec, and a Silver Division at Cobalt, Ontario. In 1979 the Silver Division milled 41,700 mt (46,000 st) of ore at a recovered grade of 139 g per mt (4.06 oz per st) for a production of 5,816 kg (187,000 oz) of silver. The 100 -year -old mining, camp of Cobalt has long been noted for its high-grade silver ores, and now seems to be on the threshold of being revived with several companies operating in the area. In 1979, the Gold Division milled at the rate of 27,200 mt per month (30,000 st) and processed 333,000 mt (367,000 st) at a grade of 6.58 g per mt (0.192 oz per st) with a mill recovery of 91.670 to produce 2,013 kg (64,700 oz) of gold. The average total cost per ton milled was $22.10 per mt ($20.05 per st) which was $3.66 per g ($1 13.90 per 0s). These figures make Agnico-Eagle one of the lowest cost producers in North America. Gold occurrence in the Joutel ore is fine-grained and contained within sulfide facies composed mainly of pyrite with minor pyrrhotite. Two underground mining methods are employed with long hole stoping accounting for about 75% of the ore mined and shrinkage stoping the remainder. Ore from underground is hoisted into a 545 mt (600 st) coarse ore bin from where it is conveyed to a 45 mt (50 st) surge bin ahead of the 10-51 Hydrocone crusher. Crushed ore is then screened to make a 13 mm (112 in.) product with the oversize being recrushed in a 7-60 Hydrocone. Mill feed is conveyed to two 900 mt (1,000 st) fine ore bins. The Hydrocones were installed as part of a new crushing plant in March of 1980 and have contributed substantially to an increase in mill capacity. Space has been left to install a third crusher in the future. The fine ore bins discharge to a 2.75 m by 3.66 m (9 ft by 12 ft) rod mill, followed by a 3. 7 m by 5.5 m (12 ft by 18 ft) ball mill in closed circuit with a Krebs 380 mm (15 in.) cyclone to produce a 7070 minus 37 micron (400 mesh) .flotation feed. This pulp is first treated in a 34 cu m (1, 200 cu ft) Maxwell flotation cell and then in an additional twelve 2.8 cu m (100 cu ft) cells. Combined flotation concentrates are reground to 9070 minus 37 microns (400 mesh) in a 1.8 m by 4.9 m (6 ft by 16 ft) ball mill in closed circuit with a single Krebs 254 mrn (10 in.) cyclone. Flotation tailings are sent to the tailings dam. Reground concentrates are then aerated with lime to a single Pachuca and thickened in a 16.75 m (55 ft) diameter thickener with the addition of diesel fuel to render any activated graphite inert to adsorption of

Jan 1, 1981

By D. E. Trout, W. R. Hibbard

Previous investigations have shown that the cold rolling textures1n2 and the drawn wire textures3 of copper change their secondary components after the addition of about 1 pct aluminum and 5 pct zinc, but do not change after the addition of as much as 30 pct nickel. However, few data are available on compression textures. Barrett4 reports from unpublished work with E. L. Layland that compression rolled copper develops a texture which is predominately (110) in the compression plane with a secondary spread to (113) and weaker spread to (100) as shown in Fig 1. However, 70-30 alpha brass similarly treated develops a texture again predominately (110) in the compression plane and with a weak secondary spread to {113} but with moderate (111) secondary intensities illustrated in Fig 2. Experimental Procedure Specimens of the compositions shown in Table 1 remaining from a previous investigation3 were annealed to a grain size of 0.090 mm average diam and machined to cylinders 0.20 in. diam and 0.20 in. high. Cylinders were compressed 90 pct reduction in height between lubricated steel blocks in a tensile machine. Glancing X ray photo-grams using copper K-alpha radiation were taken at an angle of 0 degrees to the compression surface. (111), (002) and (220) rings were analyzed to define the textures shown in Table 1. The results are in agreement with Barrett4 as to types of textures and are essentially in agreement with previous work1,2,3 as to the effects of composition. In the wire study3 it was reported that the 4.99 pct zinc alloy had a brass-type texture, while the data in Table 1 indicate a copper-type texture for compression. The wire specimen of the 4.99 pct zinc alloy was re-examined by X rays and it was established that the [loo] component still exists in the wire axis. Therefore, Table 2 of Ref. 3 is in error and should indicate a double [ill], [loo] copper-type texture for this alloy. This correction results in complete consistency with regard to compositional effects, namely that copper and its alloys containing up to approximately 1 pet aluminum, 5 pct zinc and at least 30 pct nickels develop a copper-type texture and more concentrated copper-aluminum and copper-zinc solid solution alloys will form a brass-type texture. Summary Compression textures developed in copper and its alpha solid solution alloys of aluminum, nickel and zinc are essentially the same types as those re- ported by Barrett4 with compositional effects occurring at approximately the same percent additions as previously reported for rolled sheet182 and drawn wire.3 The Scovill Manufacturing Co., Waterbury, Conn., furnished the copper and brass alloys, performed certain chemical analyses and supplied laboratory facilities where needed. References 1. Brick, Martin and Angier: Tram. A.S.M. (1943) 31, 675. 2. Dahl and Pawlek: Zlsch. Melall. (1936) 28, 266. 3. Hibbard and Yen: Trans. AIME 175, 126. Melals Tech.. Feb. 1948, TP 2334. 4. Barrett: Structure of Metals, mc- Graw-Hill (19421, 386.

Jan 1, 1950

By H. T. Clark

Within the last twenty years at least three sets of lattice constants for the room temperature (alpha, hexagonal close packed) phase of titanium have been reported in the literature. These values, summarized in Table 1, differ one from another by amounts far greater than can be explained on the basis of inaccuracies in parameter measurements. This paper presents new values determined for high purity titanium. It also details the effect of two elements, oxygen and nitrogen, on these parameters and shows that two of the previously reported values are probably in error because of the presence of one or both of these elements in the material used for examination. Preparation of Samples The titanium+ used for this study was prepared by the thermal decomposition of titanium tetraiodide7 on a hot titanium filament. This titanium rod was prepared for X ray examination by melting about 10 g in purified argon in an electric arc furnace on a cold hearth. This cast button was cold rolled to 0.040 in. thick sheet, cleaned, annealed in vacuum at 1000°C and cold rolled to 0.020 in. thickness. About 0.003 in. of surface material was then removed by hand grinding on papers to remove any contamination caused by the rolls and the sample was bent to the radius of the focusing camera. The sample was then vacuum annealed at 600°C, a temperature just high enough to cause recrystallization, producing a fine grained structure. Such a structure is essential in sheet specimens prepared for focusing cameras in order to have a sufficient quantity of grains to develop continuous diffraction lines. The use of sheet specimens rather than powder samples appears to be essential for the X ray examination of titanium. This is because of titanium's exceptionally high gettering power and its rapid absorption of adsorbed gases, water -vapor, and the like at annealing temperatures. While the effect of this contamination may be neglected for sheet specimens, its effect on 200-300 mesh powder is appreciable. Titanium alloys of oxygen and nitrogen were prepared by a technique simi- lar to that described above except that the required amount of the highest purity titanium oxide or nitride available was added prior to melting in the arc furnace. These materials were added by placing them in holes drilled in the titanium. A small weight loss invariably occurs during the melting of these oxygen and nitrogen alloys. This is believed to be due entirely to the loss of some of the powdered compound in the blast of the electric arc, an assumption which is justified on the basis that there is no weight loss during the melting of titanium metal and that wet analyses for nitrogen on representative samples have checked with the calculated analyses when it was assumed that the entire loss during melting was due to the loss of titanium nitride powder. These alloy buttons were reduced to sheet in the same manner as used for the unalloyed titanium. Experimental Procedure A North American Phillips 12 cm diam symmetrical precision focusing vacuum camera and copper radiation

Jan 1, 1950

By J. A. Cahill, A. D. Kirshenbaum

Using an alumina or zirconia crucible with an alumina sinker or a molybdenum sinker coated with zirconium dioxide, the density of liquid iron was determined by the immersed-sinker method over the temperature range of 1800" to 2500°K. The density, with respect to temperature, is ex-Dressed by the equation Dg/cm = 8.523 - 8.358 X 10 T'K The molar Volumes and thermal coefficients of expansion were calculated. Iron, upon me1ting, was found to expand 3.5 pct. A basic knowledge of the physical properties of materials at high temperatures is becoming increasingly important. A check of the literature shows, that in spite of the importance of iron, very few measurements have been made of its physical properties in the liquid state. Density measurements have been made by Benedicks and his collaborators1g using the method of balanced columns, by Desch and smith4 using the immersed sinker method with an alumina sinker, by Lucas using the maximum bubble method5 and by Stott and endall' who used an alumina pyknometer. In the method of balanced columns, the difference in level of molten iron in two arms of a U-tube, together with the corresponding difference of pressure had to be measured. The formation of gas bubbles in one or both arms was a great source of error. These values are very erratic. They vary from 6.83 to 7.45 g per cm3 at the melting point (1805"~) and from 6.45 to 7.15 g per cm3 at 1890°K. Stott and Rendall determined the density at 1837"K, with a reproducibility of *0.2 pct. They used an alumina pyknometer fired to 1973°K. The vessel was filled in a vacuum furnace by immersion in the liquid metal. When thermal equilibrium was attained, the pyknometer was withdrawn, cooled, the ingot removed and then weighed. The chief disadvantage of the method was the difficulty of inserting the pyknometer without cracking it. The authors have been able to determine the density of liquid iron from its melting point up to 2500°K, by using the immersed-sinker method, with A1203 or ZrOz crucibles and A1203 or molybdenum sinkers coated with Zr02, Fig. 1. EXPERIMENTAL Apparatus. In these studies the source of heat was the carbon tube resistance furnace with an argon atmosphere described previously.7 Experimental runs were made using either Ala3 or ZrOz crucibles. The sinkers used were 1) pure A1a3 and 2) molybdenum coated with ZrOz. The crucible, 2 1/8 in. in diam and 3 in. high, was centered in the furnace on an Ala3 of Zr02 pedestal. The sinker, 1/2 in. in diam and 1 1/2 in. long, together with a counter weight, was suspended from an analytical balance into the melt by a molybdenum wire. Procedure. The procedure, as described previously,' consisted in measuring the weight loss of the sinker in the liquid iron while determining simultaneously the liquid iron temperature by means

Jan 1, 1962

By S. I. Liu

THE effects of strain histories, consisting of several prestrains in opposite directions, on the flow and fracturing characteristics of metals determined in a final test have been investigated previously.'" Such strain histories vary from a single prestrain in tension or compression to the number of strain cycles leading to fatigue failure.' Between these two limits, various strain histories could be visualized and some can be attained readily. One such example is a strain history consisting of a first prestrain in tension of various magnitudes and a second prestrain in compression also of various mag-nitude. In this investigation the strain history was extended to the combination of these two limits, i.e., a single prestrain in tension or compression followed by balanced strain cycles of a selected magnitude e, = k0.12. It was found in this case that only compressive initial prestrains could be investigated with sufficient accuracy.* Such strain histories can be considered also as (low cycle) fatigue tests of a metal subjected to various amounts of cold working. It appears from previous publications that cold working within a wide range of reductions usually raises the un-notched fatigue strength of many metals.'-' This effect, however, has been found to be inconsistent and sometimes reversed for other metals?.7 Furthermore, Ludwik reports that the yield strength of cold-worked specimens may be reduced by cyclic strains, while that of materials without cold work is generally increased in the initial cycles." " In addition to the above tests, a study was made of the effect of intermediate re-solution heat treatment on low cycle fatigue behavior. Such anneals should eliminate the strain hardening induced by the cyclic strains. As far as their effect on the fracture characteristics is concerned, a few previous tests seemed to indicate that the damage resulting from cyclic strains is retained only partially after heat treatment." A further investigation was made in which one specimen was subjected to repeated unbalanced tension cycles in which the strain interval was approximately $ 0.013. This repetition of plastic tension damages the material slightly. This result appears to confirm Ludwik's observations." " Commercial 3/4-in. rod of the aluminum alloy 24ST4 was selected for this investigation. The material was subjected to the following treatments before machining: 1—Re-solution treatment at 920" ± 10°F for 45 min, 2—water quench at room temperature, and 3—aging for four days at room tem-perature.? The treated material then was machined to desired specimen contour and tested. A coolant was used during machining to minimize any artificial aging effects of heating during machining. In some cases the 24ST4 specimens were reheat treated after having been strained. In these cases, the heat treatment was the same as the re-solution heat treatment described above. Procedure As shown in Fig. 1, threaded end specimens with a minimum diameter of 0.266 in. and a contour radius of 2 in. were used for prestraining to an axial compressive strain ranging from 6, = —0.10 to E, = —0.48. For large prestrains, two consecutive corn-

Jan 1, 1952

By A. Lee Barrett

Mine power systems are quite different in many respects from those usually found in industrial plants. Wide areas are served, usually by a circuit which is connected continuously throughout the mine. In some mines one circuit may run for several miles. There are usually a small number of branch circuits involved considering the areas covered. In all mines circuits are sectional-ized at approximately 2500 ft by means of switches. All, or at least most branch .circuits, are sectionalized by manual switches. In some mines automatic sectionalizing gear is used to give automatic overload protection at various strategic points in the system. However at the present time this practice is by no means general. Circuit hazards in mine electric systems are much greater than those encountered in industrial installation. Falls of roof or coal form a prominent hazard which may break the wire and may cause ground faults or partial ground faults. Ordinarily electric cables in mines cannot be insulated, therefore a fall can easily cause a short circuit. The humidity in most mines is greater than 95 pct and at many points the floor is wet and water may be dripping from the roof over insulators, increasing the difficulties at that point. All electrical circuits must be contained in the mine entries and space must also be provided for moving equipment and men. Consequently, because of the proximity of the power circuit to the locomotives and other moving equipment a considerable hazard is introduced. Mine haulage track is not always good so that wrecks are not unusual. A wreck frequently does considerable damage to the power circuit. A ground fault frequently results in heavy arcing which may be sustained. If the damage to the circuit is mechanical it may mean that a trip of coal has wrecked and a great deal of coal dust could be thrown into the air as a result of the wreck. The arc resulting from the ground fault could ignite the coal dust and a mine explosion would result. A continued ground fault, even if high in resistance, also may ignite the coal which may be on the bottom of the entry and a mine fire may result. The fire hazard is one of the most serious hazards in any coal mine. Since the mine circuit is completely interconnected, any power interruption resulting. from a fault seriously affects the whole operation. Unless the mine is completely sectionalized the whole mine will be shut down until the fault is located and the proper switches are opened to isolate the fault; even then large areas may still be without power if they are supplied by a single power circuit which may be opened in isolating the fault. Further, mine power is usually supplied from a relatively small number of substations and the fault may be on a stub feed circuit, in which case power cannot be restored until the fault has been cleared. Practice varies widely with respect to placement of substations. Usually they will be spaced from I to 2 miles in 500V opera-tions, and at I mile intervals or less, in 250V operation. Actual mining operations govern substation placements and no general rules can be followed.

Jan 1, 1949

By A. Lee Barrett

MINE power systems are quite different in many respects from those usually found in industrial plants. Wide areas are served, usually by a circuit which is connected continuously throughout the mine. In some mines one circuit may run for several miles. There are usually a small number of branch circuits involved considering the areas covered. In all mines circuits are sectionalized at approximately 2500 ft by means of switches. All, or at least most branch circuits, are sectionalized by manual switches. In some mines automatic sectionalizing gear is used to give automatic overload protection at various strategic points in the system. However at the present time this practice is by no means general. Circuit hazards in mine electric systems are much greater than those encountered in industrial installation. Falls of roof or coal form a prominent hazard which may break the wire and may cause ground faults or partial ground faults. Ordinarily electric cables in mines cannot be insulated, there- fore n fall can easily cause a short circuit. The humidity in most mines is greater than 95 pct and at many points the floor is wet and water may be dripping from the roof over insulators, increasing the difficulties at that point. All electrical circuits must be contained in the mine entries and space must also be provided for moving equipment and men. Consequently, because of the proximity of the power circuit to the locomotives and other moving equipment a considerable hazard is introduced. Mine haulage track is not always good so that wrecks are not unusual. A wreck frequently does consider- able damage to the power circuit. A ground fault frequently results in heavy arcing which may be sustained. If the damage to the circuit is mechanical it may mean that a trip of coal has wrecked and a great deal of coal dust could be thrown into the air as a result of the wreck. The arc resulting from the ground fault could ignite the coal dust and a mine explosion would result. A continued ground fault, even if high in resistance, also may ignite the coal which may be on the bottom of the entry and a mine fire may result. The fire hazard is one of the most serious hazards in any coal mine. Since the mine circuit is completely interconnected, any power interruption resulting from a fault seriously affects the whole operation. Unless the mine is completely sectionalized the whole mine will be shut down until the fault is located and the proper switches are opened to isolate the fault; even then large areas may still be without power if they are supplied by a single power circuit which may be opened in isolating the fault. Further, mine power is usually supplied from a relatively small number of substations and the fault may be on a stub feed circuit, in which case power cannot be restored until the fault has been cleared. Practice varies widely with respect to placement of substations. Usually they will be spaced from I to 2 miles in 500V operations, and at 1 mile intervals or less, in 250 V operation. Actual mining operations govern substation placements and no general rules can be followed.

Jan 1, 1948

By E. W. Hart, W. R. Hibbard

The room temperature flow characteristics of a series of Cu-Cr alloys are found to be related to the amount and characteristics of the chromium-rich precipitate. The results are consistent with the theory of Fisher, Hart, and Pry, which considers the trapping to dislocation loops around precipitate particles. THE use of dispersed phases for hardening metals, particularly high temperature alloys, has been practiced for several years. Current theories describing the effects of dispersions on the basis of dislocation theory have been proposed by Mott and Nabarro.l-4 rowan," and Fisher, Hart, and Pry.8 These theories recently have been discussed by Hart,' who pointed out that the experimental data available for comparison with theoretical calculations for overaged alloys are confined to studies by Gensamer, Pearsall, Pellini, and Low,8 Shaw, Sher-by, Starr, and Dorn,9 and some hitherto unpublished data on Cu-Cr alloys which will be described herein. Certain difficulties were associated with the interpretation of the first two studies. Gensamer, Pearsall, Pellini, and Low were concerned principally with interparticle spacing and did not document particle sizes. Shaw, Sherby, Starr, and Dorn included all the data in their report which was necessary for the theoretical evaluation, but their study is subject to some question1" due to difference in prior history of various specimens and due to systematic differences in particle characteristics" which appeared to be associated with differences in the magnification of their microscopic examination. The current study was undertaken to obtain critical data in a manner which avoids some of these limitations. Specimens of eight Cu-Cr alloys remaining from a previous investigation'' were available in the form of 100 mil sheet of the compositions shown in Table I. At 200 mil this material had been previously an- nealed ½ hr at 1000°C, water quenched, and cold rolled 50 pct. Samples were further cold rolled to a thickness of 20 mil for a total reduction of 90 pct. Sheet tensile specimens of standard geometry with a gage length 2½ in. long and 0.20 in. wide were machined from this sheet. These specimens were then annealed in a dried N2-H2 atmosphere for the times and temperatures indicated in Table I. This anneal served two purposes: 1—to obtain a fairly uniform and nearly constant grain size of 0.015 to 0.022 mm average diameter, and 2—to precipitate a fairly uniform, nearly spherical over-aged dispersion of essentially pure chromium. A typical microstructure illustrating the grain size and the uniformity of the dispersion is shown in Fig. 1. A typical dispersion illustrating the range of sizes and shapes of the particles is shown in Fig. 2. The tensile specimens were tested in the Instron equipment described in ref. 11 at room temperature at a strain rate of 0.04 in. per in. per min. Three tests were run on each alloy with sufficient repro-ducibility that a single true stress-true plastic strain curve could be drawn through the three sets of data for each alloy. Typical curves are shown in Fig. 3.

Jan 1, 1956

By W. H. Moore, E. T. Powell

IN the early days of mining in the Anthracite field, only the thicker and better seams of coal were mined, because of the limited mining and coal-cleaning facilities, therefore many of the thinner and less productive seams were permitted to remain unmined. With improvements in mining methods, the introduction of modem preparation plants, and the increased market demand for small-size coal, the thinner and more laminated seams have now become assets. In many instances these seams overlie the mined-out beds of the thicker and better seams, from which all recoverable coal was removed by the conventional breast-and-pillar method of mining. Some collieries in certain sections of the Anthracite field are now relying on these thinner and laminated seams. For the purpose of illustration, a large area in the Hickory Swamp-Ridge Basin of the western middle coal field has been selected, where as early as 1898 the No. 4, or Little Buck Mountain, seam was mined and pillars removed. The No. 5, or Buck Mountain, seam lying on a comparatively light pitch and with intervening strata of but 55 ft. of rock was not mined until 1935. Farther east, in the same basin the Nos. 8 and 9 seams, which are two splits of the Mammoth seam, have been mined and robbed and the workings have been abandoned since 1896. The overlying No. 9½ seam, or the upper split of the Mam- moth, and the No. 9¾ or 4-ft. seam remained virgin, with only an interval of 50 ft. of rock separating them, and with 40 to so ft. of rock strata separating the No. 9½ seam from the completely mined area of the Nos. 8 and 9 seams. These seams lie on a pitch of 45° on the south side of the basin and on 75° on the north side of the basin. Mining has been carried on in the 9½ and 9¾ seams for 3 years on both dips of the basin, for a distance of 3500 ft. In some sections the overlying strata of the thicker seams previously mined have settled without any apparent breaks in the upper strata, as indications have shown in the top split of the Mammoth; while in other areas the roof and bottom of this top split of the Mammoth have settled unevenly, thereby causing the bottom and roof to break into blocks. In attempting to mine over a large area of the No. 5 or Buck Mountain seam, a similar settlement has been encountered; the roof of the seam has been broken and a considerable amount of timbering has been necessary in order to make the mining of the seam possible. The conventional breast-and-pillar method, using shaker conveyors, has been used in the No. 5 seam, and a slant-breast method in the mining of Nos. 9½ and 9¾ seams. Mining OF Light-pitch Seams The No. 4 seam was mined and robbed by the conventional breast-and-pillar system. In this area the seam pitched from 5° to 25° on the north dip, averaged 8 ft. in thickness and had a slate bottom and a

Jan 1, 1942

By J. K. Kerver, J. S. Osoba, J. G. Richardson, J. A. Hafford

A detailed study of a number of methods of relative permea-abilitv measurement has been made in a search for the tech-niqrle most suited to routine analysis of cores taken from reservoir rock. It has been found from tests run on the same samples of core material by a number of techniques that the Penn State, Hassler, Hafford, and dispersed feed techniques all yield results which are felt to be reliable. Conditions under which the faster single core dynamic technique may be used are described. Further work on the calculation of relative permeabilities to oil from data obtained by the gas drive method is needed before this latter rapid method can be utilized. Correlations between theoretical studies and experimental results have been obtained in studies of the boundary effect. pressure distribution in two-phase flow, and gas expansion effects. Previous conclusions that the effects of the outflow boundary could be made negligibly small have been substantiated. Results of experimentally determined oil and gas pressure distributions along a core sample during flow are presented. Further studies of the effects of rate of flow in the measurement of relative permeability-saturation relations have shown that results are independent of the rate of flow as long as the flow rate is below the point where inertial effects commence. An analysis of the effects of a severalfold expansion of gas along the flow path indicates that while saturation gradients are induced in the test sample, the errors caused by this phenomenon in relative permeability measurements are small. INTRODUCTION Many pages of literature have been devoted to pointing out the need for relative permeability-saturation relations in reservoir engineering. One of the most attractive ways of obtaining this information is by the analysis of samples of core material taken from the formation in question, and again literature has described man); methods for obtaining these data. It is the purpose of this paper to present the work that has been done in the study of some of these published methods together with some other methods that have been recently developed in this laboratory. Also, a study of some of the factors that influence the laburatory determination of relative permeability-saturation relations is presented. FACTORS WHICH AFFECT LABORATORY STUDY OF FLUID FLOW THROUGH RESERVOIR ROCK To determine relative permeability-saturation relations of samples of reservoir rock in the laboratory, it is important to know what factors affect these measurements in order that the magnitude of these effects can be ascertained and steps then can be taken to eliminate or, in some cases, to minimize them. The factors that have been investigated are the boundary effect, the effect of gas expansion. and the rate effect. Boundary Effect In laboratory experiments in which two immiscible fluids are flowed through a porous medium, there exists a discontinuity of capillary properties at the outflow face. This discontinuity exists became the fluids pass from a region of finite capillary pressure in the sample to a region of zero capillary pressure in an open receiving vessel. The capillary forces existing in the core caupe the rock to tend to retain

Jan 1, 1952

By W. H. Moore, E. T. Powell

IN the early days of mining in the Anthracite field, only the thicker and better seams of coal were mined, because of the limited mining and coal-cleaning facilities, therefore many of the thinner and less productive seams were permitted to remain unmined. With improvements in mining methods, the introduction of modem preparation plants, and the increased market demand for small-size coal, the thinner and more laminated seams have now become assets. In many instances these seams overlie the mined-out beds of the thicker and better seams, from which all recoverable coal was removed by the conventional breast-and-pillar method of mining. Some collieries in certain sections of the Anthracite field are now relying on these thinner and laminated seams. For the purpose of illustration, a large area in the Hickory Swamp-Ridge Basin of the western middle coal field has been selected, where as early as 1898 the No. 4, or Little Buck Mountain, seam was mined and pillars removed. The No. 5, or Buck Mountain, seam lying on a comparatively light pitch and with intervening strata of but 55 ft. of rock was not mined until 1935. Farther east, in the same basin the Nos. 8 and 9 seams, which are two splits of the Mammoth seam, have been mined and robbed and the workings have been abandoned since 1896. The overlying No. 9½ seam, or the upper split of the Mam- moth, and the No. 9¾ or 4-ft. seam remained virgin, with only an interval of 50 ft. of rock separating them, and with 40 to so ft. of rock strata separating the No. 9½ seam from the completely mined area of the Nos. 8 and 9 seams. These seams lie on a pitch of 45° on the south side of the basin and on 75° on the north side of the basin. Mining has been carried on in the 9½ and 9¾ seams for 3 years on both dips of the basin, for a distance of 3500 ft. In some sections the overlying strata of the thicker seams previously mined have settled without any apparent breaks in the upper strata, as indications have shown in the top split of the Mammoth; while in other areas the roof and bottom of this top split of the Mammoth have settled unevenly, thereby causing the bottom and roof to break into blocks. In attempting to mine over a large area of the No. 5 or Buck Mountain seam, a similar settlement has been encountered; the roof of the seam has been broken and a considerable amount of timbering has been necessary in order to make the mining of the seam possible. The conventional breast-and-pillar method, using shaker conveyors, has been used in the No. 5 seam, and a slant-breast method in the mining of Nos. 9½ and 9¾ seams. Mining OF Light-pitch Seams The No. 4 seam was mined and robbed by the conventional breast-and-pillar system. In this area the seam pitched from 5° to 25° on the north dip, averaged 8 ft. in thickness and had a slate bottom and a

Jan 1, 1942

By H. R. Brannon, J. S. Osoba

The introduction of the scintillation counter into field use for gamma-ray well logging has provided a new tool with special utility for the deternzination of natural radioactivity of sediments. Previous subsurface gamma-ray measurements have indicated only the total amount of radioactivity of the sediments. With the scintillation counter, the relative amounts of the elements which emit gamma radiation can be determined. Sediments logged included 35 zones in wells located in the Teras Gulf Coast, East Texas, and West Teras. Although the data obtained from measurements made to date are not sufficient to evaluate the possibilities of spectral logging, it appears likely that spectral measurements will yield information of geologic value. INTRODUCTION Although variations in the natural radioactivity of sediments were recognized as early as 1909,1 the appli- cation of such variations to borehole logging was not made until almost 30 years later. A group of Russian workers in the early 1930's were successful in making crude measurements of natural gamma activity in an oil well borehole. The first practical gamma-ray logging system was developed by Howell and Frosch2 in 1939. Induced radioactivity, or neutron, logging appeared soon after the introduction of gamma-ray logging. After early work had demonstrated the potentialities of radioactivity logging, development of sensitive and stable logging equipment for field use followed, so that neutron and natural gamma logs are now run routinely and have proved to be extremely valuable in characterizing subsurface formations. Even though tremendous strides have been made in developing radioactivity logging, it is apparent that the ultimate in the method of logging has not been reached, for, until very recently1 in none of the commercially available logging systems has advantage been taken of the fact that gamma radiation is composed of a spectrum of rays, each ray having a distinct and characteristic energy. An individual gamma ray originates in a single element and has energy determined by the element. The inten- sity of radiation, or number of rays emitted from unit volume in unit time, is determined by the concentration of the element. If it were possible to sort out these gamma rays and assign them to their parent elements, thereby essentially analyzing for the elements, a wealth of new information descriptive of formation material and fluid content would be at hand. For example, if in natural gamma logging, the gammas due to potassium and to the thorium and uranium series were measured individually, data would thus be available on the concentrations of each of the three elements, adding materially to the information content of the log. In contrast, conventional gamma logs measure only a quantity proportional to the combined concentrations of uranium, thorium, and potassium. The naturally radioactive elements occur in sediments in concentrations dependent on source material of the sediment, and through their chemical characteristics, on conditions of deposition,' so that the individual concentrations may be diagnostic for particular formations. These concentrations, particularly if measured in situ, could lead to a powerful tool for correlation and for reflecting environmental conditions under which sedimentation took place. As a correlation tool, individual uranium, thorium, and potassium measurements

Jan 1, 1957

By W. A. Backofen, G. Mayer

Single crystals of iron, copper, and a Cu-7 wt pct A1 alloy were pulled through conical dies to simulate the constraint in a polycrystalline aggregate undergoing axisymmetric reduction. With Taylor-type hardening, dependence of the drawing stress, od, on the Taylor orientation factor, M, is predictable from the polycrystal stress-strain curve; in particular, for a power-law relationship, it should follow that d log od/d log M = (1 + n). A first-order agreement with analysis was found in the data from iron. For copper, the implied n from the observed d log od/d l°g M was -0, while for Cu-7Al it was negative. The trend was in the direction of random polycrystal behavior. Thus the idea of hardening only in response to the amount of prior slip loses validity as stacking fault energy (SFE) is lowered. Two possible explanations have been suggested: as stacking fault ribbons are widened, barriers from dislocation reactions become increasingly effective in dispersing slip and reducing the orientation dependence of the total glide strain dm that appears in alternatively, or conjointly, the polyslip shear stress, 7, acquires an orientation dependence of a kind which has the same leveling effect on M. The problem of relating the strain hardening of polycrystalline material to that of an isolated single crystal is still largely unsolved. In a new experimental approach from recent work, single crystals of different orientations have been deformed under the constraints found in an aggregate while measuring their deformation resistance. Procedures have involved drawing cylindrical crystals through conical dies1 and compressing slab-shaped crystals in plane strain.2'3 Predictions for the outcome of such experiments were made first by Taylor~ and later, in more general form, by Bishop and Hill.5'6 Taylor's example was the axisymmetric extension of an fcc crystal slipping on the usual {111}(110) systems or, equivalently, a bcc crystal undergoing 'kestricted" slip on {110}(111). In his solution, the deformation work supplied was equated to that dissipated internally in slip on all active systems. With o the single applied tensile stress, dc the resulting axial strain, and dyT the total glide strain on systems operating at resolved shear stress, 7: The orientation dependence of M was found by minimizing dyT for each orientation while activating five independent systems, Fig. l(a).? The Bishop and Hill analysis, based on a principle of maximum work, leads to essentially the same conclusion; the need for at least five active systems is recognized in the finding that either six or eight are actually brought into operation. The mean value from the entire stereo-graphic triangle in either case is M - 3.06. More recently, Hutchinson8 made a Taylor-type analysis for pencil glide in a bcc structure, from which piehlerg prepared Fig. l(b) as the counterpart in Fig. l(a); here M = 2.75. The obvious weakness in such analyses is the indifference to slip-system interactions. A condition of what might be termed "independent"

Jan 1, 1969

By Regis M. N. Pelloux, N. J. Grant

Five or six alloys each in the systems Ni-C.v, Ni-Mo, and NL-W, spaced to cover the single phase areas as well as a part of the adjacent two-phase field, were prepared as uacuum-melted alloys. Tensile tests at room temperature and stress rupture tests at 1200° and 1500°F we.ve run for time periods to give fracture in 0.1 to 500 hr. Observations mere made of solid-solution and second-phase strengthening or uleakening, coupled with studies of ductility and the role of structure on the noted behavior patterns. THE development of stable creep-resistant alloys while broad and systematic is also highly empirical. A number of simple rules have been suggestedL-" but these are based on scant data. Whereas rules for low-temperature alloy strengthening can be applied with some success in more simple systems, the extension to behavior at high temperatures (greater than about 0.4 of the absolute melting temperature) is very poorly understood and has encountered important exceptions and deviations in terms of atom size or valency effects. In particular, the occurrence of both solid-solution weakening4,5 and second-phase weakening2 at high temperatures is of interest. MATERIALS AND PROCEDURE Nickel was chosen as the base material because of its important role in current high-temperature alloy applications, because of its freedom from a phase transformation, and because of wide solubilities for many elements of interest. The selected alloys were single- and two-phase structures in the Ni-Cr,6 Ni-Mo,7 and Ni-w 8 systems. The alloys were vacuum melted and cast, utilizing high-purity raw materials, in the form of 15 lb ingots. They were readily forged into 1/2-in. bar stock (except the two highest chromium alloys). The alloy compositions are shown in Table I. Typical impurity values are: Carbon: Max 0.03 pct (except for 30 and 35 pct Cr alloys which had 0.07) Nitrogen: Max 0.005 pct (except for two of the Cr alloys which had 0.05) Sulfur: Max 0.004 pct Silicon: Max 0.05 pct Each alloy was solution treated (air quenched) to produce comparable grain size. The two-phase alloys were then overaged in an effort to produce a stable structure for testing at 1200° and 1500°F, The results are summarized in Table 11. Following the heat treatments outlined in Table 11, the bars were machined to a gage section of 1.25-in. long by 0.250-in. diam. In addition to room-temperature tensile tests, stress-rupture tests were run at 1200" and 1500°F for time periods from 0.1 to about 500 hr. RESULTS Room-Temperature Mechanical Properties—The ultimate tensile strength, total elongation, and reduction of area values for all the alloys are plotted vs atomic percent of the solute element in Fig. 1. It can be seen that for the same amount of solute element the ultimate tensile strength increases in the order chromium, molybdenum, tungsten. Elongation increases (reduction of area decreases) with increasing amounts of solute for all the solid solution alloys, the values ranging from 50 to 70 pct. The ultimate tensile strength values for the two-

Jan 1, 1961

By W. H. Moore, E. T. Powell

IN the early days of mining in the Anthracite field, only the thicker and better seams of coal were mined, because of the limited mining and coal-cleaning facilities, therefore many of the thinner and less productive seams were permitted to remain unmined. With improvements in mining methods, the introduction of modem preparation plants, and the increased market demand for small-size coal, the thinner and more laminated seams have now become assets. In many instances these seams overlie the mined-out beds of the thicker and better seams, from which all recoverable coal was removed by the conventional breast-and-pillar method of mining. Some collieries in certain sections of the Anthracite field are now relying on these thinner and laminated seams. For the purpose of illustration, a large area in the Hickory Swamp-Ridge Basin of the western middle coal field has been selected, where as early as 1898 the No. 4, or Little Buck Mountain, seam was mined and pillars removed. The No. 5, or Buck Mountain, seam lying on a comparatively light pitch and with intervening strata of but 55 ft. of rock was not mined until 1935. Farther east, in the same basin the Nos. 8 and 9 seams, which are two splits of the Mammoth seam, have been mined and robbed and the workings have been abandoned since 1896. The overlying No. 9 ¾ seam, or the upper split of the Mammoth, and the No. 9 ¾ or 4-ft. seam remained virgin, with only an interval of 50 ft. of rock separating them, and with 40 to 50 ft. of rock strata separating the No. 9 ½ seam from the completely mined area of the Nos. 8 and 9 seams. These seams lie on a pitch of 45° on the south side of the basin and on 75° on the north side of the basin. Mining has been carried on in the 9 ½ and 9 ¾ seams for 3 years on both dips of the basin, for a distance of 3500 ft. In some sections the overlying strata of the thicker seams previously mined have settled without any apparent breaks in the upper strata, as indications have shown in the top split of the Mammoth; while in other areas the roof and bottom of this top split of the Mammoth have settled unevenly, thereby causing the bottom and roof to break into blocks. In attempting to mine over a large area of the No. 5 or Buck Mountain seam, a similar settlement has been encountered; the roof of the seam has been broken and a considerable amount of timbering has been necessary in order to make the mining of the seam possible. The conventional breast-and-pillar method, using shaker conveyors, has been used in the No. 5 seam, and a slant-breast method in the mining of Nos. 9 ½ and 9 ¾ seams. MINING OF LIGHT-PITCH SEAMS The No. 4 seam was mined and robbed by the conventional breast-and-pillar system. In this area the seam pitched from 5° to 25° on the north dip, averaged 8 ft. in thickness and had a slate bottom and a

Jan 1, 1941