Search Documents

By James J. Norton, Lincoln R. Page

Effective methods for determining grade and reserves of pegmatites in advance of mining have been developed in recent years. When intensive work began on the economic geology of pegmatites during the early years of World War II, it was widely believed that grade and reserves could be estimated only in a most general way. The literature indicated that not all pegmatite deposits are unpredictable, but statements emphasizing unpredictability and irregularity seem to have been more widely accepted. Many standard references reflect the prevailing opinion that minerals are unsystematic in their occurrence in pegmatites. Pegmatites have been de- scribed as "notorious for their irregular structure," and minerals within pegmatites as "irregularly distributed," "irregularly disseminated,'' of "erratic occurrence," "proverbially erratic in distribution," "characterized by extreme irregularity in size and distribution of the essential minerals, and variety and proportion of the accessory minerals, and "spotty."

Apr 1, 1956

By Robert G. Peets

After 216 years, the end of operations at the Corn- wall mine can be foreseen within the next two decades. The story starts in 1732 when three sons of Wiliam Penn-John, Thomas, and Richard-deeded 9669 acres in the Province of Pennsylvania to a Joseph Turner, who assigned it to William Allen. In 1734 Peter Grubb, who had prospected for iron in the area, paid Allen £ 135 for 300 acres of this tract in what is now Lebanon County. In 1737 he was granted a warrant for 142.5 additional acres, which included three hills of outcropping magnetite described as "rich and abundant, forty feet deep, commencing two feet under the earth's surface." This seemingly inexhaustible reserve was to become one of the most valuable deposits in the U. S. before the ore-rich Lake Superior region was developed.

Jan 7, 1957

By K. P. Gupta

The Cb-rich boundary of the (Cb,Al) a phase field at 1250OC is near 41 pct Al. The Al atoms tend to occupy the C. N. 12 sites in this structure. A homologous (Ta,Al)a phase was identified. No a phase was found in the Mo-Al system at 1200°C. The first binary o-phase with a non-transition element as a major component was found1,2 in the Cb-Al system. The composition of this phase was reported2 as approximately 34 at. pct Al, based on X-ray diffraction patterns taken of alloys in the as-cast condition. Further study of the composition of this o-phase, therefore, appeared desirable. Since Si was previously found3,4 to occupy preferentially the lowest C.N. sites (I and IV) in the a phase, and preliminary resultsa indicated that Al may show similar ordering, one of the aims of the present work was to obtain more complete information on ordering in (Cb, Al) o. Among the binary systems of Al with Ti-, V-, and Cr-group elements, the Ti-Al, Zr-Al, V-Al, and Cr-Al systems are known to comprise no o-phase. In the present work a Ta-Al and a Mo-Al alloy were studied in an effort to find additional o phases with Al as a major component. EXPERIMENTAL PROCEDURES AND RESULTS An alloy with the intended composition of Ta + 40 at. pct Al was prepared by arc melting in He atmosphere. In both the as-cast condition and after annealing for 10 days at 1250°C and quenching in cold water this alloy consisted of two phases, as seen in the X-ray pattern and the microstructure. One of these phases was identified as the o-phase; the observed and calculated d-spacings are shown in Table I. The lattice parameters of this o-phase are a = 9.972 A, c = 5.214 A and c/a =0.5228, as determined from a Debye-Scherrer pattern using Fe K a radiation. The d-spacings for the unknown second phase are given in Table 11. The alloy contained approximately 25 pct of the unknown phase after annealing, as estimated on the basis of microscopic examination. A Mo-Al alloy was prepared by arc melting, with an intended Al-content of 35 at. pct. The alloy button was annealed for 7 days at 1200°C and water quenched. The X-ray pattern of the alloy in both the as-cast and the annealed state showed the reflections of Mo3Al (Cr30 type structure) and an unknown phase different from a. Six Cb-Al alloys were prepared in the composition range 30 to 50 pct Al. All alloys were arc melted in He atmosphere. After annealing for three days at 1175oC in evacuated silica capsules and quenching in water, the alloys with 30 to 40 pct Al contained three phases, namely the o-phase, Cb3Al (Cr3O-type structure) and an unknown phase. The alloys with more than 40 pct Al contained two phases, namely, what appeared metallographically, the o-phase and the same unknown phase. In the alloys containing less that 38 pct Al, the unknown phase was not present after annealing for 4 days at 1250°c,

Jan 1, 1962

By C. Scala, M. Gondouin

Published laboratory data have established that very significant streaming potentials can exist across mud cakes subjected to pressure differentials such as exist between a mud column and formation fluids. Since shale is similar in kind and in properties to a well-formed mud cake, it appeared possible that streaming potentials might also arise across shales. A practical consequence would be that the streaming potential contribution to the SP would be smaller than might otherwise be assumed since the SP is measured with respect to the "shale bare line". The resultant contribution would be the difference between the streaming potential across the shale and that across the mud cake. In order to investigate this possibility, a laboratory apparatus was devised for measuring streaming potentials under pressure conditions normally encountered in wells. Reported data on streaming potentids across mud cakes were verified. More important, appreciable streaming potentials were found across shale samples. As in the case of mud cakes, the shale potentials varied with the concentration and nature of the impregnating electrolyte. Dependence on pressure was In a different rela-tion than that for mud cakes, possibly because of the lower compressibility of shales. The differences in streaming potentials between the shales md mud cakes were generally small, although they might vary considerably in practice depending on the relative electro-kinetic properties of the particular shale-mud cuke combination. A "poorly eflective" shale with a "very eflec-tive mud cake" would produce the largest negative addition to the electrochemical component of the SP. Results of field experiments with pressurized wells were considered in the light of the laboratory results. INTRODUCTION Field experiments wherein the pressure of the mud column in a borehole was varied have often indicated the presence of a streaming potential, but its magnitude was not easily predictable and its sign sometimes changed from one formation to another in the same well.' In the interpretation of SP logs from standard surveys, nevertheless, the correct value of R,, is very frequently obtained, within the limits of field accuracy, using only the simple electrochemical expression of the SP provided that proper corrections are made for bed thickness, ion activity, etc.' Accordingly, it was apparent that the streaming potential component of the SP in a borehole was considerably more complex than commonly assumed and clarification was indeed necessary The close similarity in nature and constitution of a shale to a well-compacted mud cake suggested that a streaming potential might also exist across shales as pointed out by M. P. Tixier in 1953 and as recently emphasized by Wyllie." e practical consequence would be that the streaming potential across the mud cake would be canceled, at least in part, on electrical logs since the SP is recorded with respect to the shale potential as a base line. This appeared to be a plausible explanation for many of the effects observed but no supporting data were available. In 1955 preliminary experiments at low pressures were conducted in our laboratories which supported the hypothesis of the shale streaming potential and formed the basis for later studies at borehole pressures.* EARLY LOW PRESSURE EXPERIMENTS The early experiments were conducted primarily to determine the possibility of a streaming potential across shales. The shale used was a compact type designated as No. 7 from Reagan County, Tex. (Permian). Cut samples were saturated for over one month in .2 to 2.0-N NaCl solutions. In order to eliminate all electrode polarization effects, a dynamic method was used. A transient pressure of about 1 atm was applied across

By D. H. Thompson, A. W. Tracy

E. A. ANDERSON*—At the outset, I note that you are using a humid atmosphere containing ammonia but that you make no reference to the variable of carbon dioxide content. Edmunds in his work in this laboratory found very marked effects on the rate of failure due to variations in carbon dioxide in the environment. This point is, of course, strongly related to the overall corrosion rate problem since the role of the carbon dioxide seems to be to permit the formation of hygrogroscopic salts which give a controlled moisture film on the specimen surface, which in turn seems to support the intergranular penetration more consistently than would otherwise occur. (2) Your results with various copper binary systems are very striking. It is curious, however, that the time-to-failure minima all occur at percentages of the alloying element which are considerably below the solubility limits as given in the conventional equilibrium diagrams. If your theory regarding the presence of these impurities in some concentration in the grain boundaries is correct, then either the existing diagrams are not accurate in the room temperature region, or there is a difference in solubility in the grain boundaries as compared -with the grains. A study along these lines might be very revealing. (3) The undesirable effect of silicon in copper calls to mind our own observations on the influence of silicon on the stress corrosion cracking resistance of alpha brass. In this case, silicon was found to have a very marked beneficial effect, particularly when a heat treatment capable of producing a grain boundary constituent was used. I should appreciate it if in the discussion of your paper this point should arise, you would attempt to clarify the difference between the copper-silicon binaries and the copper-zinc-sili-con ternary alloys. D. H. THOMPSON and A. W. TRACY (authors' reply)—(1) We have no data on the constancy of the carbon dioxide content of the air used for the test atmosphere but have believed that the normal carbon dioxide content of the air was as constant as could be obtained by using Edmunds' method of removing carbon dioxide from the air and then adding a measured quantity. In any event, the test atmosphere was the same for all specimens in a test run. We agree with Mr. Anderson that the carbon dioxide content is important in the formation of a hygroscopic film on specimens. (2) We can imagine that there could be a concentration of solute atoms at the grain boundaries which would be so small that present methods would not detect it even if it exceeded the solubility limit of the alloy. There could be somewhat greater solubility at the grain boundaries for an interstitial solute. There is a possibility that phosphorus dissolves in this way but we believe that none of the other solutes studied does. In our present studies we hope to find out something about conditions at the grain boundaries of some of the systems mentioned in the paper. (3) Mr. Anderson points out that silicon brass, which has had a high temperature heat treatment followed by a quench. is highly resistant to stress-corrosion cracking. Although the test conditions used by Anderson* et al were different from our test conditions, it is noted that the silicon brasses which had not had the special heat treatment were less resistant to stress-corrosion cracking than copper containing approximately equal amounts of silicon. G. R. GOHN†—Nonferrous metallurgists and particularly, materials engineers, have been accustomed to thinking

Jan 1, 1950

By T. G. Digges, M. R. Achter

ALTHOUGH zone melting has found favor in recent years because of its convenience and its faster rate of production of single crystals, the older technique of strain annealing still has a number of advantages. It has been reported1 that the lattice of a crystal prepared in this manner has fewer defects than one grown from the melt and, of course, the control of the external geometry is easier. Also, the diameter of the crystal which can be grown by zone melting has a theoretical limit determined by the surface tension, thermal conductivity, and specific gravity of the material, while the size of that which can be grown in the solid state is limited only by practical considerations. In a program for the study of the structure-sensitive properties of niobium and its alloys it was desirable, for ease of handling, to have available single crystals of large diameter. This requirement dictated the choice of the strain-anneal technique. Induction heating was chosen in the present work in preference to other methods because of its deep penetration of large-diameter sections. A five-turn coil, powered by a motor generator operating at 10,000 cps, is contained in a vacuum chamber. The work is lowered through the coil for both the recrystallization and the crystal-growth steps. Starting with electron-beam melted material, the bars are cold-swaged, recrystallized, strained in a tensile machine, and then subjected to the growth step. Single crystals have been grown under the following conditions: Reduction in area during swaging— 79 to 99 pct, recrystallization temperature—1500o to 1667°C at the rate of 1.25 in. per hr, strain—1.0 to 2.5 pct, growth temperature—1600o to 2400°C at rates from 0.15 to 1.25 in. per hr. Starting grain sizes achieved after the recrystallization step varied from 0.6 to 1.55 mm. The starting grain size was found to be critical; if it is too fine and has any residual cold work, as shown by the presence of a fiberlike texture, a single crystal cannot be grown. Using this technique niobium single crystals have been grown from 0.250 in. diameter and 12 in. long to 1.00 in. diameter and 5 in. long as shown in Fig. 1. The 1-in. crystal is the largest to be reported for a refractory metal as compared to 0.500 in. for molybdenum grown by zone melting.2 As with zone melting, control of orientation is possible by the use of special procedures. Other investigators, see for example Williamson and Smallman,3 have reported that orientation control may be achieved by a bending technique. In the present work the strained rod is partially lowered through the coil to start the growth of the crystal. Then it is removed and bent at a point ahead of the interface between the single and polycrystalline portions. Finally, it is returned to the chamber and growth is continued "around the corner". The amount of bending which can be imparted to the rod is limited by coil geometry which up to now has been 10 deg. However, by repeating the bending and growing operations it should be possible to attain any desired orientation. The perfection of these single-crystal specimens as a function of process variables is being measured by X-ray and metallographic techniques and the results will be reported in a forthcoming paper. This work was partially supported by the Advanced Research Projects Agency.

Jan 1, 1964

By W. L. Phillips

Nickel alloys containing approximately 0.5, 2.0, and 6.0 at. pct of Os, Pd, Ru, and Rh were Prepared by vacuum melting. Tension tests were carried out at 25°, 500°, 800°, and 1000°C; stress-rupture tests were carried out at 650° and 800°C. The room- and elevated-temperature tensile strength, as well as the stress-rupture life, increased for the same atomic percent in the order palladium, rhodium, ruthenium, osmium. The ductility decreased with increasing concentration or temperature for a given concentration. The results are discussed in terms of solid-solution theory. BOTH solid-solution strengthening and weakening have been observed in alloys. The simple rules which have been suggested to explain alloy strengthening are subject to several exceptions and deviations based on atom size and valency effects. The purpose of the present investigation was to extend the knowledge of the effect of solid-solution alloying on the mechanical properties of several Ni-Pt group metal alloys at room and elevated temperatures. The platinum group metals, osmium, ruthenium, rhodium, and palladium were chosen as the solute elements because of their different valencies and atom sizes. Nickel was chosen as the base material because of the large amount of previous literature available on nickel alloys. EXPERIMENTAL PROCEDURE Grade A Carbonyl nickel powder having the following composition: C, 0.07 pct; Fe, 0.013 pct; Mn, 0.0005 pct; Si, 0.016 pct; Mg, 0.0003 pct; S, 0.003 pct, was purchased from the International Nickel Co. The platinum-group metal powders were purchased from A. D. Mackay Co. The powders were weighed, cone-blended for 4 hr, and vacuum-melted into 1-in.-diam billets, approximately 2 in. long. The ingots were homogenized for 5 hr at 1800°F before being extruded into 1/4-in. rods at 2100°F. The alloy compositions are shown in Table I. Typical impurity values were not significantly different than that of the as-received nickel. All alloys were single phase. The lattice parameter of each alloy after the heat treatment described below is also included in Table I. Each alloy was annealed at 2200°F for 1 hr and air-quenched to comparable grain sizes (ASTM G.S. No. 4-5). The rods were then machined into test samples 0.160-in. diam and 0.750-in. gage length. Tension testing was carried out in an In-stron tension-testing machine at a strain rate of 0.02 in. per in. per min. An extensometer was used to determine the room-temperature yield stress. Stress-rupture testing was carried out in an Arc Weld stress-rupture unit. All testing was performed in air. EXPERIMENTAL RESULTS A) Room-Temperature Mechanical Properties. The 0.2 pct yield stress, ultimate tensile strength, and elongation for all alloys tested at room temperature are plotted as a function of atomic percent solute element in Fig. 1. The ultimate tensile strength for the same atomic percent increases in the order palladium, rhodium, ruthenium, osmium. The yield strength at low concentrations, -0.5 at. pct, increases in the order osmium, palladium, ruthenium, rhodium. At higher concentrations, 3.0 and 10.0 pct, the yield strength increases in the same order as the tensile strength. Both yield strength and tensile strength increase rapidly ini-

Jan 1, 1964

By Samuel Storchheim

IT was noted that variations existed in the magnetic properties, namely, coercive force, He, and rema-nence, Br, of 18/8 stainless steel wires of the same analysis when these wires were given the same percentage of reductiori of area at different rates of reduction. In order to determine the extent of these variations, a program was initiated whereby commercial 302 and 304 stainless steels were drawn with a wide variation of speeds. Ultimate tensile strengths and specific resistances, as well as the Hc-BT measurements, were determined. If variations of considerable magnitude were found, it was thought that the knowledge accrued from the investigation could probably aid in determining the particular drawing speed required to obtain desired properties for a given specification for a particular analysis of wire. Drawing Procedure Two specimens (set I, No. 302 and No. 304), the chemical analyses of which are given in Table I, were drawn at different speeds, namely, 45 to 3900 ft per min, directly from 0.016 in. diam wire to 0.004 in. diam wire, a 93.7 pct reduction of area. To obtain this high percentage of reduction, the wire at 0.016 in. was softened by annealing at 1150°C. It was then strung in a No. 16CF variable speed Vaughn drawing unit and passed through 13 B.&S. gage dies of successively smaller diameter, as shown in the accompanying table. Following this step, several hundred feet of the wire was drawn, at a particular speed, through the dies and wound upon a spool. Once the sample of wire was drawn at the desired speed, the spool with the finished sample was removed, tagged for later identification, and an empty spool was placed in the machine. Another wire sample was drawn at a different speed, after making the necessary adjustments upon the Vaughn unit. At the greater speeds, several thousand feet of sample were drawn to insure that the wire to be used for testing would be uniform. This was done because the desired speed was not reached instantly; the wire taking a short while to attain the required drawing rate. All speed measurements were made by placing a tachometer against one of the machine's pulleys during the actual drawing of the specimens. 84.4 pct reduction of area. The 0.072 in. diameter wire was also annealed at 1150°C. The process of obtaining samples was the same as described above. The only difference between the two was that the rates involved were not as extensive, set II covering a range of 625 to 1150 ft per min. Tensile tests were carried out for the 0.004 in. diam wires on a horizontal Scott Tensile Tester, while tensile tests for the 0.028 in. diam wires were made on a vertical Scott Tensile Tester. Each value listed in the tables represented the average of five samples with a maximum deviation of approximately 3 pct among the samples. Resistance per foot of the wires was determined by use of standard bridges accurate to the nearest hundreth of an ohm for the 0.004 in. wire, and to the nearest thousandth of an ohm for the 0.028 in. wire. The resistances per foot were then converted to resistivities by use of the following equation: P = RxCM where R is the resistance per ft in ohms per ft; CM, the area in circular mils; and P, the resistivity in ohms—CM. The values listed in the tables likewise

Jan 1, 1952

By C. A. Bruch, W. E. McHugh, R. W. Hockenbury

Commercially pure molybdenum specimens were irradiated in the Materials Testing Reactor for an estimated exposure of 1.9 to 5.9x10 20 thermal nvt. Prior to irradiation, the material was ductile in the tension test; whereas after irradiation, it was brittle. The results of tension tests conducted at various temperatures revealed that the transition temperature for this material had been increased from —30' to +70°C as a result of the radiation exposure. From metallographic studies, it is concluded that the embrittlement is due to submicroscopic changes which raise the flow stress-temperature curve of the material. PRIOR to ten years ago, the bombardment of metals with high speed heavy particles such as protons, deuterons, a particles, and neutrons was primarily of academic interest. These particles existed in extremely small numbers in a few laboratories and only under very special conditions. With the introduction of the nuclear power reactors, these particles are now available in enormous quantities and it has become important from a practical standpoint to learn how well metals withstand severe reactor radiations. The principal radiations of concern in reactors are neutrons and y rays, since the heavier charged particles exist only in limited regions of reactors. Seitz,' in a theoretical approach, has shown that all of these high energy particles, except y rays, have enough energy to knock atoms from lattice sites and that these knocked-on atoms have enough energy to cause additional displacements of neighboring atoms. The result of this process would be a lattice containing many imperfections in the form of interstitial atoms and vacancies. Hence, it would be expected that the properties of metals can be changed by reactor radiations, and such has been found to be the case. Only a limited amount of data have been published in the open literature,2,3 and these data have been for relatively low integrated-neutron-flux exposures. In general, one effect of reactor radiations on the mechanical properties of metals has been to increase strength and decrease ductility. It is now possible to irradiate specimens in the Materials Testing reactor at much higher fluxes and to higher integrated exposures than previously possible.' The data which are being presented here describe the effects of a relatively high exposure on some mechanical properties of molybdenum. Experimental Procedures Material: The molybdenum used in this investigation was obtained from the Climax Molybdenum Co. The two heats from which the material originated were melted under a vacuum of 5 to 30 microns and cast in 7 in. diam water-cooled copper molds. One ingot contained 0.061 pct C and the other 0.066 pct. Both ingots were hot worked by extrusion and rolling into % in. diam rods, after which they were annealed and straightened. The rods were subsequently heated to 1100°C in a hydrogen atmosphere and swaged to ½ in. diam rods at the Research Laboratory of the General Electric Co. The resulting material had an average hardness of 264 VPN, or 99.2 Rb, and had an average of 5000 grains per sq ml in the transverse section, Test Specimens: Substandard-size tensile specimens were prepared according to the specifications shown in Fig. 1. These specimens were used also for hardness measurements. The metallographic specimens were small disks which were polished, etched, and photographed at X1000 prior to irradiation. The field studied was

Jan 1, 1956

By A. W. Demmler

RECENTLY, Chaudron,&apos; Montariol,2 and their co-workers published the results of their studies on zone-refined aluminum. They found their material to be capable of recrystallization at —50°C, but gave no data as to the percentage reduction or time required. Their material was found to be practically non-work hardening at room temperature, but after 96 pct cold work at a low temperature and storage in liquid nitrogen it was found to recrystallize to coarse grains in less than 3 hr at 20°C. Recently, a study was made of the room temperature recrystallization characteristics of zone-melted aluminum. An ingot 14 in. in length, with a 3hx3 in. cross section, was made in an extremely high purity graphite boat under an atmosphere of dried commercial argon. It was made by first passing the molten zone along the ingot of 99.99+ pct A1 15 times. At this point, the most impure 3 in. (the end toward which the eutectic forming impurities migrated) were replaced with more of the original starting material, and 15 more traverses were made. Each traverse of the zone along the ingot required approximately 3 hr. Three ingots were prepared in this identical fashion and the chemical analyses were made spec-trographically on two of these ingots, rather than on the one used in this investigation. The analyses were made at 1 in. intervals along the ingot, in duplicate. Over the purest 5 in. of the ingot, which were most important in this investigation, there was found an average composition of <0.00004 pct Cu, <0.0003 pct Fe, <0.0001 pct Si, and <0.0001 pct Mg. In addition, the following elements were not detected spectrographically even in the more impure end of the bar: manganese, zinc, nickel, chromium, titanium, vanadium, lead, tin, boron, beryllium, bismuth, gallium, zirconium, cadmium, antimony, cobalt, and molybdenum. The original ingot was given several cold reductions, with intermediate anneals in order to refine the grains. Owing to the extreme length resulting and the ease of deforming the material plastically, it was cut into eight equal lengths and identified as shown in Fig. 1, with the highest numbered section at the purer end (that enriched with peritectic formers). Section 6 was used in the exploratory work and was found to be of exceptionally high purity, giving more rapid rates of room temperature re crystallization than any previous aluminum studied at the Alcoa Research Laboratories. This fact suggested that the entire midsection of the ingot might be of very high purity. Accordingly, section 4 was chosen for the next study. A portion of it was rolled to cold reductions of 10, 25, 40, 60, 75, and 90 pct at room temperature, and the re-crystallization of each specimen was followed by X-ray pinhole transmission photographs. The other portion received the same treatment, except that both the specimens and the rolls were maintained at 160°F in the process of rolling. The latter ortion was retarded in its recrystallization as compared to the former, probably due to the stress relief effect of the warm rolling. Both of these portions of the fourth section were found to recrystallize at a considerably slower rate than did the sixth section.

Jan 1, 1957

By M. F. Goudge, R. V. Tomkins

Sodium sulfate is an important chemical raw material that is being used in ever increasing quantities in modem industry. It comes on the market mainly in three forms: (1) Salt cake (Na2SO4), a relatively crude form of the anhydrous salt containing up to 3 pct impurities, and comprising about three-quarters of the North American production; (2) anhydrous sodium sulfate (Na2SO4), a refined form containing less than 0.3 pct impurities; (3) Glauber&apos;s salt, the decahydrate (Na2SO4.10H2O) containing 55.9 pct water of crystallization. Competing with salt cake from natural sources is byproduct salt cake from a number of industrial operations. For instance there is Mannheim cake resulting from the manufacture of hydrochloric acid by the reaction of salt (NaCl) and sulfuric acid in Mannheim furnaces; rayon cake, a high-quality product, resulting from the process of making rayon by the viscose process; chrome cake from the processing of sodium chromate to dichromate; phenol cake from the manufacture of phenol; also byproduct sodium sulfate resulting from the conversion of lithium sulfate to lithium carbonate; from the processing of sodium tetraborate to boric acid; from converting sodium formate to formic acid; and in the manufacture of cellophane. Sodium sulfate is also obtained as a byproduct in the manufacture of isosebasic acid. In addition strong competition has resulted from imports of byproduct salt cake from the chemical industries of a number of highly industrialized European countries. However in recent years due to technological changes the output of byproduct salt cake is rapidly diminishing and the natural deposits are becoming the most important source of sodium sulfate used in North America. For instance, the production of hydrochloric acid in Mannheim plants has become obsolete and thus the greatest single source of byproduct salt cake will disappear. Also viscose rayon is meeting strong competition from nylon and other synthetic fibers and production of byproduct salt cake from this source may do little more than remain at the present level. These factors together with increasing demand for sodium sulfate point to increased production from natural sources. In 1958, 36 pct of the total United States production was derived from natural sources and in addition 97,000 short tons was imported so that over 40 pct of the total consumption was supplied by natural sources whereas in 1953 the proportion was only 24 pct. The rapid growth in production is shown in Table 1. Principal Sodium Sulfate Minerals There are many minerals in which sodium sulfate is a constituent but those of commercial importance at the present time, and consisting wholly of sodium sulfate in either the hydrous or anhydrous states, are mirabilite and thenardite. Minerals of potential importance but consisting in part of compounds other than sodium sulfate are glauberite in which sodium sulfate is combined with calcium sulfate, and blödite in which sodium sulfate is combined with magnesium sulfate. Mirabilite (Na2SO4.10H2O) the decahydrate, consists of 24.8 pct SO3, 19.3 pct Na2O, and 55.9 pct H20. It is a colorless to opaque, soft, water-soluble mineral with a slightly bitter taste. It has a hardness of less than 2 and a specific gravity of 1.48. It forms long needle-

Jan 1, 1960

By S. A. Falconer

This paper deals with the practical application of the Dutch State Mines cyclone separator for fine-coal cleaning. The more important operating variables are discussed, and results of a number of continuous-scale tests on various fine coals with a 6-in. cyclone separator are given. Descriptions of the Cyanamid Pilot Plant and the 50 tph Cyclone Separator Plant at the Emma Washery in Holland are included. TODAY, as never before, the coal producers of this country are faced with the necessity for obtaining maximum yield of marketable coal of all sizes down to and including the finest. Particular interest is being displayed in a more effective means of recovering the finer sizes which in the past so often have been discarded to waste or treated by inadequate equipment. The reasons for this interest are easily understood. Rising mining costs have resulted in the increased use of mechanized equipment underground for full seam mining. This, in turn, means more refuse in the run-of-mine and also more fines in the feed going to the cleaning plant. Stringent antistream pollution laws now make it necessary at least to impound the fines, and usually it is a paying proposition to recover the coal from these fines before sending them to the storage area. Finally, the market and price of the finer sizes has increased, but at the same time specifications have tightened and the demand is for higher grade products. During the past four years a great deal of publicity has been given to this new process and apparatus for treating fine sizes of ores as well as coal. Excellent discussions of the apparatus itself and the theoretical aspects of the basic operating principles involved in its operation have been presented by M. G. Driessen,1-3 M. R. Geer and H. F. Yancey,4,5 J. W. Hyer6 and more recently by D. A. Dahlstrom8 as well as others.7,9-11 In view of this, it has been decided to include in the present paper only a brief description of the cyclone separator and its operating principles. This paper deals primarily with some of the more practical commercial aspects of the process and equipment required for its operation; the variables in the operation of the cyclone, their effect and means for control; and the results obtained with a 6-in. semicommercial size separator on a variety of fine coals, bituminous and anthracite, using finely ground magnetite for the separating medium solids. A description is included of the commercial-size cyclone separator pilot plant installed by the Dutch State Mines at its Emma mine in Holland, where finely ground slate is utilized as medium solids. Field of Application: The Dutch State Mines cyclone separator operates most efficiently on ores and coal in the size range of % in. to about 48 mesh. On some types of feed, effective separation can be made on sizes as small as 100 mesh, but up to the present, this may be considered exceptional. Depending upon the type of medium used, the specific gravities of separation can be varied within wide limits, up to as high as 2.70, if magnetite is used as medium. Early Development: The development of the Dutch State Mines cyclone as a separator, or cleaner, was the outgrowth of early experimental work by Dries-sen&apos; and others in Holland, just prior to World War 11, in the course of which was discovered the effectiveness of the cyclone in reclaiming and thickening the dense medium used in the "Loess" process of

Jan 1, 1951

By S. A. Falconer

This paper deals with the practical application of the Dutch State Mines cyclone separator for fine-coal cleaning. The more important operating variables are discussed, and results of a number of continuous-scale tests on various fine coals with a 6-in. cyclone separator are given. Descriptions of the Cyanamid Pilot Plant and the 50 tph Cyclone Separator Plant at the Emma Washery in Holland are included. TODAY, as never before, the coal producers of this country are faced with the necessity for obtaining maximum yield of marketable coal of all sizes down to and including the finest. Particular interest is being displayed in a more effective means of recovering the finer sizes which in the past so often have been discarded to waste or treated by inadequate equipment. The reasons for this interest are easily understood. Rising mining costs have resulted in the increased use of mechanized equipment underground for full seam mining. This, in turn, means more refuse in the run-of-mine and also more fines in the feed going to the cleaning plant. Stringent antistream pollution laws now make it necessary at least to impound the fines, and usually it is a paying proposition to recover the coal from these fines before sending them to the storage area. Finally, the market and price of the finer sizes has increased, but at the same time specifications have tightened and the demand is for higher grade products. During the past four years a great deal of publicity has been given to this new process and apparatus for treating fine sizes of ores as well as coal. Excellent discussions of the apparatus itself and the theoretical aspects of the basic operating principles involved in its operation have been presented by M. G. Driessen,1-3 M. R. Geer and H. F. Yancey,4,5 J. W. Hyer6 and more recently by D. A. Dahlstrom8 as well as others.7,9-11 In view of this, it has been decided to include in the present paper only a brief description of the cyclone separator and its operating principles. This paper deals primarily with some of the more practical commercial aspects of the process and equipment required for its operation; the variables in the operation of the cyclone, their effect and means for control; and the results obtained with a 6-in. semicommercial size separator on a variety of fine coals, bituminous and anthracite, using finely ground magnetite for the separating medium solids. A description is included of the commercial-size cyclone separator pilot plant installed by the Dutch State Mines at its Emma mine in Holland, where finely ground slate is utilized as medium solids. Field of Application: The Dutch State Mines cyclone separator operates most efficiently on ores and coal in the size range of % in. to about 48 mesh. On some types of feed, effective separation can be made on sizes as small as 100 mesh, but up to the present, this may be considered exceptional. Depending upon the type of medium used, the specific gravities of separation can be varied within wide limits, up to as high as 2.70, if magnetite is used as medium. Early Development: The development of the Dutch State Mines cyclone as a separator, or cleaner, was the outgrowth of early experimental work by Dries-sen&apos; and others in Holland, just prior to World War 11, in the course of which was discovered the effectiveness of the cyclone in reclaiming and thickening the dense medium used in the "Loess" process of

Jan 1, 1951

By E. J. Rapperport, M. F. Smith

A presentation of the W-Ru constitution diagram is given. Techniques utilized in the determination of phase boundary values include electron micro-probe analysis of two-phased alloys and diffusion couples, as well as normal metallographic and X-ray methods. The primary features of the diagram are: 1) a terminal solid solution of ruthenium in tungsten with a maximum solubility of 23 at. pct Ru at 2300°C; 2) a terminal solid solution of tungsten in ruthenium with a maximum solubility of 48 at. pct W at 2205°C; 3) a o phase of maximum breadth about 6 at. pct based on the composition W3Ru2 which forms peritectically from the melt at 2300°C, and which decomposes eutectoidally at 1667 °C to form a twigs ten and 0 ruthenium; 4) a eutectic at 45 at. pct Ru and 2205°C with the products being o plus ß ruthenium. THE W-Ru diagram has previously been studied only in a cursory fashion. Raub and alter&apos; obtained a 1400°C isotherm in which they observed no intermediate phases, and on which they established the limits of solubility as 36.5 at. pct W in ruthenium and about 1.5 at. pct Ru in tungsten. In addition, Obrowski2 found a o phase forming peritectically from the melt and existing only above 1650°C. Below this temperature the phase was presumed to decompose eutectoidally. The present work finds the diagram as given in Fig. 1. I) EXPERIMENTAL PROCEDURE The materials used for alloy preparation in determining the W-Ru constitution diagram were 99.9 pct pure ruthenium powder supplied by Baker Chemical Co., and 99.9 pct pure tungsten powder from General Electric Co. Typical analyses of these elements are given in Table I. Initial alloys at 10 at. pct intervals were prepared from the metal powders by the following method. Powders sufficient for 25 g of the alloys were weighed out with an accuracy of 0.1 mg and blended mechanically. After blending, the powders were compacted, in a steel die, at approximately 30,000 psi. The compacts were sintered in an electric vacuum furnace in order to remove adsorbed gases and to achieve partial densification prior to arc-melting. Vacua of 10-4 mm Hg or less were maintained in sintering as the furnace temperature was raised to approximately 2000°C. Sintering times ranged from 10 to 20 hr. The sintered compacts were arc-melted under a protective atmosphere of purified helium. Melting was conducted on a water-cooled copper hearth, utilizing a nonconsumable tungsten electrode. In the melting process, each alloy was turned over and re-melted on opposite sides from four to six times to ensure complete melting and to eliminate gross in-homogeneities. The arc-melter used had a vacuum capability of 5 X 10-6 mm Hg, and a leak rate of about 20 -liters per hr. Chemical analysis techniques for refractory metal-platinum group metal combinations are not well-established; therefore, composition control and determination depended principally upon weight-loss observations and calculations. This consisted in weighing each alloy after sintering and after arc-melting, and calculating the maximum and minimum composition values, assuming the total weight losses to be first all tungsten, and then all ruthenium. Since composition uncertainty was directly related to weight loss, care was taken to minimize losses in handling, compacting, and melting. Prior to homogenization and equilibration the as-arc-melted alloys were analyzed in several

Jan 1, 1964

By J. Phillip Neal, Kefton H. Teague, Carroll P. Rogers

Feldspars, the most abundant minerals of the igneous rocks, occur in numerous forms and mixtures. The feldspars of commercial significance are found in widely distributed pegmatites as large crystals usually free of iron-bearing impurities and thus suitable for hand-cobbing, and also in larger bodies where the ore contains various types of feldspar intermingled with quartz and relatively free of iron-bearing impurities, or at least readily unlocked from impurities present at relatively coarse mesh. The latter type of ore includes some pegmatites, and the "alaskite" bodies so common in the Spruce Pine district of North Carolina. On the west coast of the US and in Oklahoma there is-or has been-commercial recovery of natural feldspathic sand as a source of alumina in glass and ceramics. "Aplite" in commercial terminology is a light-colored igneous rock with a granitic composition and a fine sugary texture, often banded with readily removable iron impurities. Only one area in Virginia produces aplite for the glass industry; it is located near Montpelier in Hanover County. According to Deer et al. (1966) the word feldspar derives from the Swedish feldt or jolt (field) and "spath:" chunks of rock appearing in tilled ground overlying granite. Castle and Gillson (1960) indicate a Germanic origin, citing "spat," which is said to refer to any transparent or translucent material which is readily cleavable. The term "spar" has in the past been applied to minerals other than feldspar, such as barite, calcite, and fluorite. It is correct to call the latter "fluorspar." There is a true barium feldspar, but it is rare and of no present economic importance. What is recognized as feldspar or "spar" by present producers and consumers consists of three silicate minerals which, if pure, would have the formulas KA1Si3O8 (microcline or orthoclase), NaAlSi3O8 (albite), and CaAl2Si2O8 (anorthite). These are almost never found in pure form in nature, but occur together in great abundance in a three-component system. A considerable number of different combined ratios of these three exists, with the exception that isomorphism between potassium spar and calcium spar is very limited. User specifications for feldspar products are largely built around the prevalent naturally occurring ratios. Passages following will refer to "K-spar," "Naspar," or "Ca-spar." Nomenclature and Descriptive Terms Relating to both the mineralogy and the economics of feldspar are certain terms whose coverage it is useful to specify. Commercially, aplite is a feldspathic rock mined and beneficiated in one location in Virginia, in which both titanium and feldspar minerals are present-the latter now being the major, if not the only, economic product. Technically, the term aplite when applied to this rock is of questionable accuracy. But, in light of accepted commercial usage, the term will be here used to designate it. Regarding the Virginia rock, Ross (1941) is cited. Alaskite is another term requiring understanding if not precise use. A distinctive rock type customarily called by this name is found near Spruce Pine, Mitchell County, North Carolina. An important major feldspar source, it contains somewhat higher levels of plagioclase feldspar and quartz than alaskite as defined in the Glossary of Geology and Related Sciences, which states that `orthoclase, microcline, and subordinate quartz are the principal

Jan 1, 1983

By R. L. Slobod, B. H. Caudle

In the past, the main emphasis in attacking the problem of the recovery of oil has been on the determination of fluid flow characteristics and residual oil saturation in the part of the reservoir which is contacted by a displacing phase. It is recognized that the determination of the fraction of the reservoir contacted in secondary recovery operations is also of great importance in predicting the ultimate recovery to be expected. A method is described in which radiographic techniques are used to determine these areal sweepout factors for any type of well spacing. Data showing the relationship of viscosity ratio and relative permeability to areal sweepout efficiency are presented for the five spot and the direct line drive well spacing patterns. Further applications of the method to studies of the displacement efficiency in the area contacted are mentioned. INTRODUCTION The problem of increasing oil recovery from typical reservoirs is generally attacked by trying to devise some means for reducing the residual oil in that part of the reservoir which is contacted. The fraction of the reservoir contacted in the displacement process. however, is also of major importance but has been given less consideration in the past. one reason for this neglect is the meager information available on the portion of the reservoir contacted and the magnitude of changes in this factor as operating conditions are varied. Until recently, the only means available for determining this quantity has involved the use of the electrolytic or poten-tiometric modelsl in which one is limited to working with a mobility ratio of unity. while means for calculating the volume of a reservoir contacted do exist. the calculations are very tedious for systems with mobility ratio different from unity. Recently several such determinations have been reported,213 and an experimental method involving a step-wise use of potentiometric models has been described.&apos; A new method which has been developed for studying the areal distribution of phases in a porous medium is discussed below. This tool can be&apos; used to determine the effect of operating variables such as viscosity, relative permeability, presence of gas, mobility ratio, rate and stratification on the fraction of the reservoir contacted by the displacing medium. This development based on the use of X-rays gives a pictorial representation of the location of the phases. Further, the amount of each phase at each point of interest can be determined quantitatively. X-RAY METHOD FOR AREAL STUDIES In this method the location of various phases distributed Over a test area are observed simultaneously by obtaining a photographic record of the transmission of X-rays through the test plate. This procedure is an adaptation of the radiographic techniques which have 10% been used in the medical and industrial fields. Just as the medical profession uses a chest plate to show spatial interrelationships, the location of an X-ray absorbing fluid and a nonabsorbing fluid in a porous medium can be determined by obtaining a photographic record of transmitted X-rays. Moreover, as changes occur in such a System, these changes can be observed by taking successive photographs. Previously, X-ray methods have been used in fluid flow studies to determine quantitatively the saturation at a given point in the system. The intensity of the transmitted X-rays was measured by an ionization chamber, so that a point by point survey of saturation could be made. In comparison with this earlier quantitative procedure, the photographic procedure which simultaneously observes the saturation at many

Jan 1, 1952

J. B. Cohen (AVCO Mfg. Co.)-The model presented by the authors is only one of several possible mechanisms for low-temperature aging. It is true that the motion of dislocations to the copper atoms, followed by diffusion along the dislocation lines, is one such mechanism. However, the details of such a process which would :result in copper-rich platelets on (100) planes in the f.c.c. matrix are not clear. Furthermore, there is at least one other mechanism that may be used to e.xplain the authors&apos; results, so that the data do not clearly favor the Turnbull model. The zones may form by "normal" diffusion. The diffusion constants would be higher at room temperature than extrapolated data would suggest due to vacancies trapped in the specimens in the quench. The diffusivity would then be multiplied by the ratio of the number of vacancies present at the solution temperature to that present at room temperature. These vacancies could remain in the alloy specimen for long times at room temerature, due to interaction with the copper atoms. &apos; The activation energy for diffusion is smaller than that for bulk diffusion at elevated temperatures for it is only that for the motion of vacancies existing after the quench; after these are used up, the aging process effectively ceases. It is somewhat questionable if the laws governing transformation kinetics can be directly applied to changes in elastic moduli, especially in the case of aging where the structure and the composition of the zones may be changing during aging, If such laws are assumed, it is possible to explain the exponential factor of % with this vacancy model. It is probable that the structure of the zones and the matrix match only on (100) planes. Certainly the precipitates that form in this system after various aging treatments show orientation relationships similar to those of the zones. Strains on the edges of the zone may set up fields which do not allow the zone to grow in an edgewise manner. The exponent in the growth of a thin plate in a direction perpendicular to its face would be %. It may also be that copper atoms are attracted to dislocations. If this is the rate-controllin factor in the growth process Ifthisthen an exponent of % or % may arise. The writer would like to know if the authors have tried plotting l/a; proportional to as might be expected for "dislocation drainage." R. H. Doremus (General Electric Research Laboratory)—An important new method for following the growth of Guinier-Preston zones is presented in this paper, and I wish to congratulate the authors on their experiments. Their interpretation of the results, however, is doubtful in certain respects. To determine the exponent m in Eq. [4] the authors plotted -log at against t to various powers (their Fig. 6). The initial value of frequency used for these plots was found by extrapolating the data to zero time. In Fig. A the data from their Fig. 2 are plotted against a linear, rather than logarithmic, time scale. To obtain graphs similar to their Fig. 6 for these data one must use an initial frequency of about 52720; such a plot for m = % is shown in Fig. B. The straight line in Fig. B fits the data in an intermediate range only. The curve drawn in Fig. A was mapped from this line; comparison of

Jan 1, 1960

By R. F. Domagala, M. Hansen, D. J. McPherson

On the basis of metallographic analysis, incipient melting data, thermal analysis work, and X-ray diffraction, phase relationships in the 0 to 50 atomic pct Cr region were carefully resolved. Phase relationships in the 50 to 100 atomic pct region were outlined. A single intermediate phase, ZrCr,, was established in the system. A eutectic and a eutectoid were found in the zirconium-rich region of the system, while a eutectic was located in the chromium-rich region. Limited solubility of chromium in both a and a zirconium was observed. THIS is another in a series of papers on zirconium-base binary phase diagrams based on a program sponsored by the Atomic Energy Commission. The Zr-Sn,&apos; Zr-Si,&apos; and Zr-Mo and Zr-W" systems have already been published. Previous work on the Zr-Cr system includes a partial diagram by Hayes, Roberson, and Davies&apos; and a complete diagram by McQuillan." The phase relationships reported by these authors were determined with magnesium-reduced zirconium, whereas those reported herein are based on iodide metal. Some X-ray work on the intermediate phase in this system was also reported by Hayes et al., as well as by Wallbaum.&apos; Comparisons with these data are made in the appropriate sections. Thermal analysis, metallographic and incipient melting techniques were employed to accurately resolve phase relationships in the 0 to 50 atomic pct Cr region, while the remainder of the diagram is outlined on a basis of cast structures and thermal analysis. A description and analyses of the metals used in the preparation of alloys for this study are included in Table I. A "low-hafnium" zirconium crystal bar (Westinghouse "Grade 3") was used. This material was produced by the decomposition of a volatile iodide onto a hot zirconium filament. The as-received crystal bar was coated with corrosion product from a standard autoclave test by which its grade designation is determined. A sand-blasting and subsequent HF-HNO, pickling treatment was employed to remove this contamination. The bars were cold-rolled to approximately 1/32-in. sheet, pickled again, sheared to 1/4-in. squares, washed with acetone, and stored for use. Ingot chromium metal from National Research Corp. and electrolytic chromium flakes from Johnson, Matthey and Co., Ltd., were available as alloy additions. The ingot chromium was received in granular form. The large granules were sized by crushing, treated for iron removal, rinsed with acetone, and stored. The flakes were broken to approximately 1/8 in. with mortar and pestle, cleaned with acetone, and stored for charging. Experimental Procedure A nonconsumable electrode arc furnace identical to that described by Hansen, Kessler, and McPher-son,&apos; was used in this work. A 400 amp dc welding generator was the source of power. To insure homogeneity, ingots were melted in a water-cooled spun copper crucible, a total of four times without opening the furnace. No difficulties were encountered in the preparation of these binary alloys. Analyzed chromium contents were found to agree very well with the intended content. Melts of pure zirconium were interspersed in the course of preparing the alloys and their hardness was measured to keep a constant check on the melting technique. Vycor and quartz bulbs were used to contain the samples for isothermal annealing treatments. Vycor bulbs were employed for temperatures up to 110O°C, while quartz was used above this temperature. For treatments up to 950°C the bulbs were evacuated before sealing, but for higher temperatures a partial pressure of argon was admitted to the

Jan 1, 1954

By L. J. Ingvalson, Roy H. Miller

IN 1948, as part of a program to expand the copper tube mill facilities of the American Brass Co. plant at Kenosha, Wisconsin, plans were formulated to convert the 100 ton capacity anode casting furnace at the Great Falls, Montana plant of the Anaconda Co. to the production of 3 in. phosphor -ized billets. The furnace was rebuilt completely and construction was started on an addition to the building. Members of the Great Falls staff visited various billet casting plants to draw upon the experience of other producers of this type of casting. Many features of other plants were incorporated into the Great Falls plant but, in addition, many new designs were made and perfected to make the plant the most advanced of its type. Construction was begun in 1949, with the intention of having the plant in production in the early part of 1951. In January 1951, as the plant was being rushed to completion, the government placed restrictions on the production of copper tubing. As a result, work was halted and the plant lay idle for two years. Interest was reactivated in May 1953 with the lifting of restrictions on copper. Plans were laid to go into production in July and the first charge was taken out July 1, 1953. Basically the plant is designed to produce from cathode copper a 3 in. diam billet, 50 in. long. weighing 110 lb, and containing 0.013 to 0.036 pct P, at a rate of 150,000 Ib per operating day. These billets are to be pierced and drawn into tubing. Furnace The furnace is a 100 ton capacity reverberatory type, gas fired furnace; 21 ft long and 9 ft wide. Gas is introduced to the furnace through two 38 hole Mettler gas burners. These burners are of chrome nickel alloy with four jets per hole. The furnace is charged with cathodes from the Electrolytic Copper Refinery plus return scrap from the casting operation by means of a Wellman Seaver Morgan Co. 7,000 lb capacity charging machine. The charge crane has a 20 ft boom and fork peel provided with an air ram to push material off the peel. The machine travels on overhead tracks and can be moved in any direction. The boom can be raised and lowered and swung through an arc of 180". With well stacked units of 6,000 lb, an experienced operator can put the first charge into the furnace in 40 min. After charging, the steel framed silica brick charge door is put in place and sealed with clay. After melting and skimming off the slag, the copper is blown until an oxygen content of 0.40 pct is reached. The metal is then heated to 2180°F, covered with coke, and poled. Poling is continued until a 3 in. diam test billet, 8 in. long, shows a flat set. The oxygen content is usually 0.030 pct at this time. At the end of poling, a temperature of 2160" to 2180°F is desired. In the side of the furnace opposite the charging door is the taphole slot, extending 36 in. upward from the bottom of the furnace. It is 4½ in. wide at the outside face and widens to 9 in. at the inside face of the furnace. It is filled with a wet mixture of sand, fireclay, and crushed coal. Flow of metal

Jan 1, 1957

By Langtry E. Lynd

The predominant tonnage use of titanium is as a white pigment, in the form of rutile or anatase, which are allotropic modifications of titanium dioxide. Because of its whiteness, high refractive index and resulting light scattering ability, titanium dioxide is unequaled as a white pigment for paints, paper, rubber, and a wide variety of other materials. Consumption of titanium dioxide pigments for these uses has been rising steadily for many years, United States consumption in 1956 amounting to about 486,000 tons, worth $250,000,000. Production was off a little in 1957 and 1958. An outstanding development in the titanium field in recent years is the expansion of titanium metal production. Virtually nonexistent before 1948, United States production of pure titanium metal sponge reached a high in 1957 of about 17,200 tons, worth about $77,000,000. United States titanium sponge metal production in 1958 was cut back to about 4,600 tons because of reductions in military requirements. Another major use of titanium, in the form of the mineral, rutile, is for welding rod coatings. United States consumption of rutile for this purpose in 1958 amounted to about 11,000 tons, worth $1,100,000. Titanium-Bearing Minerals Although several minerals contain titanium as a major constituent, only a few of these occur in sufficient quantities and concentrations to be of commercial importance. These are ilmenite (FeTiO3), rutile (TiO2), and alteration products of ilmenite which have been referred to as weathered ilmenite, leucoxene, or arizonite. The other polymorphs of titanium dioxide, brookite and anatase, occur in a few deposits, of which only one has been of even minor importance. Considerable concentrations of titanite or sphene (CaTiSiO5) and perovskite (CaTiO3) are known, but do not compete with ilmenite and rutile deposits in grade or size. Rutile is very widely distributed as an accessory mineral in most rocks, but large deposits of commercial importance are rare. A few rock deposits have been worked for rutile but only one, in Virginia, is in operation (1959). Development of one in Mexico was discontinued recently. At present, the main sources of rutile are the beach and dune sands of Australia and Florida. A major use of rutile is for the manufacture of titanium tetrachloride, which is the intermediate compound universally used in titanium metal manufacture. Another main use of rutile is for welding rod coatings. Although the whiteness and brightness of titanium dioxide pigment is due to the high refractive index of rutile or anatase, natural rutile is too impure to be used directly as a white pigment, is too expensive to use for manufacturing pure oxide pigment, and is too scarce to provide the required tonnages. Instead, the cheaper, more abundant, mixed oxide of iron and titanium, ilmenite, which is readily decomposed by sulfuric acid, is used for manufacture of rutile and anatase pigments. Ilmenite is mined from both rock and sand deposits. Rock deposits contain ilmenite in massive or heavily disseminated form along with magnetite or hematite and are almost invariably associated with anorthositic and gabbroic rocks. Ilmenite also occurs as an accessory mineral in a great many igneous and metamorphic rock types. Concentrations of

Jan 1, 1960