Search Documents

By B. H. Cody

The Morenci concentrator of the Phelps Dodge Corporation is a part of the project that was completed after five years had been spent in development of the open-pit mine, equipment and process testing in the former No. 6 concentrator, and construction of the reduction works. The reduction works, of which the concentrator is a part, is about a mile and a quarter southeast of Morenci, on the highway that leads up Morenci Canyon. The concentrator has a nominal capacity for the treatment of 45,000 tons of ore daily. The original plant, which has a rated capacity of 25,000 tons of ore daily and is now in its fifth year of operation, began production on Jan. 30, 1942. The addition, to increase the capacity 80 pct, began operation on Dec. I, 1943. The equipment of the original plant has been described in Mining and Metallurgy (May 1942). NO changes in equipment were recommended for installation in the concentrator extension and only one major change, forced by a shortage of maintenance labor, has since been made. Metallurgical treatment has been altered in some ways as experiments progressed and as labor and economic conditions dictated. No complete description of the operation of the concentrator has been published, so this paper will record such operating and equipment changes as have been necessary, the operating methods that have been developed and the metallurgical results that have been obtained. Descriptions are given in the order of the processes with a flowsheet and an equipment list of each process for convenient reference. The questions asked by engineer visitors have guided the detail in which operation and maintenance are described. During the period Jan. 30, 1942 to Sept. I, 1946, ore milled has totaled 43,595,253 dry tons, from which 1,643,885 tons of concentrate have been made, containing an indicated production of 783,164,-809 lb of copper. The principal results obtained in operation of the concentrator during the years 1942 to 1945, inclusive, and to Sept. I, 1946 are shown in Table I. A graphic general flowsheet of the plant is given in Fig I. Ore The Morenci ore that is now being treated is a medium-hard monzonite porphyry in which the principal sulphide minerals are chalcocite and pyrite. A minor amount of covellite is present. Chalcopyrite and bornite have been observed under the microscope. The chalcocite occurs mainly as a coating on pyrite. Some of the coatings are so thick that the pyrite presents the appearance of being an inclusion in chalcocite. Some are less than one micron thick and are barely visible at 500 diameters magnification of a polished cross section. Some chalcocite is present as a in in the gangue. Various oxidized copper minerals are present as a result of oxidation in place but they represent a minor proportion of the copper minerals of the ore body. Oxidation

Jan 1, 1949

By J. A. Berger, R. J. Towner

A method for determining the disorientation between sub-grains that .share a common tilt or twist boundary from measurements on X-ray micrographs is described. The method may be applied to subgrains of almost any orientation having boundary angles in the range from about 1 min to 1 deg of arc. An adaption of the Berg-Barretl method has been made to allow calculation of small angles of about 1 min to 1 deg of arc: between adjacent subgrains from the relative displacement of their images on X-ray micrographs. schulz4 gave equations for determining subgrain disorientation where the axis of subgrain rotation and the reflecting crystal planes were parallel to the specimen surface. In our method, however, they need not be parallel and, indeed, may have va:rious orientations. His camera setup, involving a fine-focus X-ray tube for obtaining high resolution with continuous radiation, was different from the one used in the present investigation (a 1.2 x 1.2 mm effective source and characteristic radiation). The X-rays produced a slight magnification in the subgrain images in the Schulz method, but not in the present method. The commonly available type of X-ray tube used permitted relatively short exposure times with a fine-grained photographic plate, which could be magnified optically many times for the examination of small subgrains. The method is illustrated by results obtained on {110} tilt boundaries in a polygonized aluminum single crystal of 99.994 pct purity. The flat crystal was stretched 6 pct in tension and then heated at 500°C for a cumulative time of 5 hr. Earlier, cahn5 studied subgrains formed by polygonization in stretched and heated aluminum crystals. He observed kink bands to have well defined boundaries lying in (110) planes, at least in the early stages of deformation. Cahn found that the (110) tilt boundaries formed by polygonization were directly related to the lattice bending about the <211> axis which lay in the (111) slip plane perpendicular to the <110> slip direction. DESCRIPTION OF THE CAMERA Our camera was similar in detail to Honey-combe&apos;s.6 Unfiltered copper radiation was used at 35 kv, and 20 ma. With the particular specimen used here to illustrate the method, a 1.2 by 1.2 mm effective source and a distance of 780 mm from target to specimen were employed, giving a convergence of 5 min of arc in the primary beam. The distance was 9.5 mm from the specimen to film. The upper 1/2- by 1-in. portion of the front surface of the specimen was irradiated with the film in parallel position. Since the specimen had been inhomogeneously deformed, many regions were in a position to reflect characteristic radiation at the Bragg Angle. Five minute exposures were satisfactory with Kodak Single Coated X-ray Film, 1 1/2 hr

Jan 1, 1961

By O. Katz, A. Spilners, M. Simnad

THE oxidation of titanium has been studied in recent years by a number of investigators.&apos;-W ne of the most important aspects of the reaction of titanium with oxygen, which has been observed by several of the investigators, is the extremely high solubility of oxygen in the metal. A detailed study of the Ti-0 systeml% as shown that the solubility limit of oxygen in a-titanium is approximately 14.5 wt pct 0 from 800" to 1700°C. The unusual oxidation behavior of titanium may be ascribed to this phenomenon, since part of the oxygen uptake enters into solid solution in the metal and only a part is available for scale formation. A more complete study of the kinetics of oxidation of titanium would require information on the influence of oxygen in solution in the metal upon the oxidation rate. Such information would also be of interest in regard to the theory of oxidation of metals. The authors have measured the oxidation rates of oxygen-saturated and oxygen-free titanium between 800" and 1200°C and have found appreciable differences in their rates of oxygen uptake and in the activation energies. The experimental set-up was similar to that described in a previous paper.u The course of oxida-dation was followed continously by attaching the specimen to a sensitive spring balance and observing the extension of the spring with time of oxidation. High purity electrolytic oxygen was used and precautions were taken to purify the gases employed. The specimens were prepared from iodide titanium and were ground on metallographic polishing papers to a fineness of 4/0. The furnace was first evacuated and filled with argon; the specimen was lowered into the furnace, which was then evacuated and filled with oxygen, after the specimen had reached the oxidation temperature in argon. The samples were presaturated with oxygen by means of the following procedure: Each specimen was first heated in oxygen at 1200°C until its increase in weight indicated 13.8 pct by weight uptake of oxygen. The furnace was then immediately evacuated and filled with purified argon five times. The specimen was heated in the argon atmosphere for a period of 72 hr at 1200°C in order to saturate the metal with oxygen by complete absorption of the scale. The temperature was lowered to the oxidation temperature, the furnace was evacuated and filled with oxygen, and the oxidation rate was followed by noting the extension of the spring balance. No oxide film was visible on these specimens at the start of the oxidation experiments. Titanium samples in the oxygen-free as-received condition were also oxidized and their oxidation rates measured. The results are shown in Figs. 1, 2, and 3, which indicate that the initial rates of uptake of oxygen by both the oxygen-saturated and oxygen-free specimens are parabolic at these temperatures. The rate of uptake of oxygen is, however, appreciably lower

Jan 1, 1956

By C. E. Birchenall, M. H. Davis

The rate of oxidation of titanium in the temperature range 650° to 950°C has been measured. &apos;The linear rate law obtained is explained by interface reaction control of the process. Tracer experiments indicate the oxygen diffuses in at least one phase of the scale. THE kinetics of oxidation of titanium, principally at low temperatures and under varying oxygen pressures, have been reported.¹,² In the present investigation the rates of oxidation of titanium have been determined by the gravimetric method in the temperature range 650" to 1000°C under 1 atm of oxygen. Some of the scales formed were powdered and an endeavor was made to identify the phases present by X-ray diffraction. Alexander and Pigeon1 ascribe a logarithmic rate law to the growth of thick films formed at temperatures up to 565"C, and Gulbransen and Andrew&apos; suggest that the parabolic rate law holds up to 600°C. In both cases large initial deviations from those relationships are apparent and no explanation is offered. In the present experiments it is shown that a linear rate law holds in the temperature range 650" to 1000°C, and it is suggested that the initial deviations observed are due in part to a spurious surface area effect and also to the high solubility of oxygen in titanium metal. Positive information on the mechanism of oxidation is not available, but oxygen ion diffusion through the lattice is inferred from the re- sults of trace experiments. X-ray analysis of the scale confirms Gulbransen and Hickman&apos;s&apos; observation on the presence of rutile TiO². Experimental Details The titanium used in these experiments was prepared by the reduction of titanium tetrachloride with magnesium and was used in the form of rolled sheet. Samples approximately 0.040x0.5x0.75 in. were cut and polished to a fineness of 4/0 on metal-lographic polishing papers. Individual samples, suspended on a platinum wire, were lowered into the hot zone of a furnace, in vacuo, by means of a winch, and oxygen was admitted after the desired temperature was attained. The increase of weight of single samples oxidized for fixed times at certain temperatures was determined by weighing the sample before and after oxidation on a chemical balance. In these instances the sample was used for only one time at one temperature. In some cases the course of oxidation was followed by attaching the sample to a sensitive spring balance and noting periodically the extension of the spring with time of oxidation. Kirkendall type experiments were carried out by marking the surface of the titanium prior to oxidation with a solution containing radioactive silver. After drying, the specimen was heated in vacuo to decompose the silver nitrate used, leaving a small amount of metallic radioactive silver on the surface. Following oxidation, these samples were mounted, ground, and then placed in intimate contact with

Jan 1, 1952

By J. C. M. Li

A dislocation model is constructed for a cylindrical tilt boundary of which the axis of tilt is parallel to the axis of the cylinder. The strain energy per unit area calculated from this model agrees with thut of an infinite vertical wall of edge dislocations. Based on this model, a dislocation mechanism for the shrinking of such a cylindrical boundary is proposed. The power relation between the grain boundary velocity and the driving force is accounted fm by the stress dependence of dislocation velocity. The activation area for grain boundary motion is found to correlate with that .for Creep in aluminum. In the preceding paper&apos; the velocity of a curved grain boundary is found to be a power function of the driving force, [1] where M is the velocity at unit driving force, y is the grain boundary energy, and p is the radius of curvature. This finding adds another nonlinear rate equation to metallurgical phenomena. While a macroscopic theory for the steady state as just presented2 can be used to understand the shape of the moving boundary, such theory usually does not provide any information about the atomistics of the process. It is attempted in this paper to discuss the nonlinear rate equation in terms of a dislocation mechanism. A DISLOCATION MODEL FOR A CYLINDRICAL TILT BOUNDARY Before a dislocation mechanism can be proposed for the motion of a cylindrical tilt boundary, it is necessary to construct a dislocation model for the boundary. For simplicity, a tilt boundary in a simple cubic lattice will be examined. Although this does not represent the situation in aluminum, it is expected that the general features will be similar. The details of the model in the fcc lattice can be constructed when a refinement of the simple model is called for. A cylindrical low angle tilt boundary in a simple cubic lattice is shown in Fig. 1. Two sets of edge dislocations are needed as shown. A schematic representation is shown in Fig. 2(a). In terms of a continuous distribution of dislocations, the density of dislocations n, of Burgers vector b, in the small segment ds of the grain boundary is Similarly the density of dislocations n, of Burgers vector bz in the same segment ds is where is the tilt angle of the grain boundary. Based on this continuous distribution of dislocations in the grain boundary, it can be shown that the interaction between a small segment of the boundary and the rest of it is zero. Furthermore, the stress produced at any point inside or outside the cylinder is also zero. This shows that the model is acceptable in the sense that the boundary has no long-range stresses. Since the model of continuous distribution of dislocations in the grain boundary does not reveal the interactions among individual dislocations, a discrete dislocation model has to be used for such purpose. For simplicity, an equivalent model is shown in Fig. 3. This arises because the total Burgers vector is, from

Jan 1, 1970

Discussion of the paper of G. P. Hulst, presented at the Salt Lake meeting, August, 1914, and printed in Bulletin No. 92, August, 1914, pp. 1865 to 1871. L. S. AUSTIN, Salt Lake City, Utah.-One question that I would like to ask is in regard to the sampling kettle which stands beside the softening furnace. How is the sample taken or melted? G. P. HULST.-The sampling kettles in question are of 45 tons capacity and are fired with coal. The lead bullion comes in on a high line in car-load lots of 30 to 40 tons. The entire lot is trucked from car, weighed over scales and thrown into the sampling kettle, which has been previously cleaned. The kettle is fired and the bullion melted, then heated up until no frozen bullion&apos; remains in the .bottom or adheres to the sides of the kettle. The kettle is scraped clean, sides and bottom, and the wet dross is skimmed Doff clean into molds. The kettle is stirred thoroughly during the period in which 24 to 30 samples of approximately ½ assay ton are taken. These samples are taken in a long-hand loci iron mold, providing for taking six to eight "gumdrops." The mold is inserted and heated to the same temperature as the molten metal, and gumdrops are clipped out and cooled in the mold by dipping &apos;the bottom of. the mold into Water. The samples should be free from fins. The gumdrops represent the contents of the kettle, and in assaying, they should not be clipped, but weighed up and the result computed. The dross bars are weighed and sawed according to old hammer and punch sample template. The sawdust represents a sample of the dross. In eases of high gold in the bullion there is a slight correction in the assay. This method of sampling was developed at the Omaha plant of the American Smelting & Refining Co., W. T.. Page, Manager, in 1903 or 1904, for adjusting differences in checking smelter sampling. L. S. AUSTIN.-The base bullion which you treat is very clean. It has been remelted, and skimmed before shipment. How rapidly can you get it through the softening furnace, and how does it compare with ordinary base bullion? G. P. HULST.-Twenty-four hours is the softening limit on these charges. In other words, it is charged into the furnace, heated up, and the first and second skimmings are taken off, and it goes into the kettle the next day; that is, 24 hr. elapse from the time the bullion is charged to the time it is in the kettle. L. S. AUSTIN.-It seems to be a long time to hold such a pure bullion. I suppose, though, it comes around conveniently so that you have a time for all the other operations of refining. Isn&apos;t that the case? MR. HULST.-Every refinery is based on those principles.

Jan 11, 1914

By Charles C. Rodd

Prior to 1938, proration procedure in Kansas required the physical testing of wells in order to set up a basis for allocating production. Subsequently the use of liquid-level data and bottom-hole pressure data was authorized on certain types of wells as a basis for calculating well capacities, thereby permitting wells to be tested at low rates and with small volumes of production. This paper gives some attention to the equipment used for obtaining liquid-level data but in general it is devoted to the theoretical and physical factors involved in well testing by drawdown methods. These tests are divided into two classifications: (I) liquid-level data used directly to calculate capacities, and (2) liquid-level data and liquid-level measuring equipment used in connection with other data to determine bottom-hole pressure. Equations and calculations for both types are shown. Well capacities calculated from fill-up data have not been used generally but offer a simple means of testing some wells. Theoretical factors and calculations for such tests are shown. In the state of Kansas, proration laws required that the "ability of a well to produce" be given consideration in state allocation orders and for many years this was the only factor used in prorating the allowed oil. The "ability of a well to produce", was the quantity of oil that could be obtained from a well in a prescribed period, usually 24 hr. Early in the history of State-regulated proration, Kansas operators realized that, unless some restriction were placed upon equip- ment, the competition between producers to obtain large well "potentials" might result in a race to install the largest pumping equipment. Consequently, restrictions were placed upon the size of tubing and length of pump stroke that could be used in pumping wells during potential tests. Later, restrictions were placed also upon the size of tubing and chokes that could be used in flowing walls. Despite the restriction setup, better pumping equipment was designed and installed, pumps were improved, and various devices were invoked to obtain high rates of production for short periods of time. By 1937 pumping cycles of forty to forty-five 54-in. strokes per minute were not uncommon, and numerous wells had produced at the rate of 3500 bbl. per day for short periods. Such production was far beyond any rate that could be long sustained. Equipment necessary to take "potentials" was several times larger than that needed for normal producing purposes, and repairs and replacements required by the high pumping speeds were excessive. Also, many operators suspected that the high rates of production main tained during &apos;"potential" tests were conducivc to early water encroachment. By 1938 large-scale physical testing of wells in Kansas ended, the use of the bottom-hole pressure gauge had become common, engineers and operators were becoming familiar with the term &apos;&apos;productivity index," and bottom-hole pressure was being used as a factor in allocation in many areas. There were many drawbacks, however, to large-scale use of

Jan 1, 1943

By B. L. Averbach, E. E. Underwood

The vapor pressure of zinc in equilibrium with solid ß AgZn alloys has been measured by the dew-point method. The thermodynamic activities of silver, and the molar heats of formation have been calculated. Similar measurements have been made for the ternary alloys formed by adding gold to AgZn. An apparent particle size effect has been observed for AgZn filings. The vapor pressure of zinc over filings is 15 to 20 pct higher than over the solid alloys. STATISTICAL methods have been used to inter pret the thermodynamic activities of the components of a solid solution in terms of average equilibrium atomic configurations. In some cases, the atomic arrangements can be measured by X-ray methods, and the results are usually expressed in terms of short range order parameters. Only in the cases of Cu³Au and AgAu have there been sufficient X-ray and thermodynamic data to verify the assumed correlation between the X-ray and the thermodynamic measurements. In Cu³Au the agreement is good; negative deviations from Raoult&apos;s law are observed and the number of Cu-Au nearest neighbor pairs predicted on the basis of the thermodynamic treatments agrees quite well with the number of such pairs observed by the X-ray methods. The ß brass alloys present a different set of conditions. The ordering is so rapid in these alloys that the disordered state cannot be retained on quenching. In contrast, the disordered state in CuAu is easily retained on quenching. On heating, the ordered ß brass loses its long range order continuously as the critical temperature is approached; in Cuau the order decreases slightly on heating and then drops discontinuously to zero at the critical temperature. These differences indicate that the short range order configurations in ß brass systems may be of a different character than in Cudu systems. However, X-ray measurements of local order cannot be made in the Cu-Zn alloys because of the similarity in scattering factors. The alloy AgZn is isomorphous with CuZn, however, and recent experiments have indicated that there is a good possibility of observing short range order in this system. Another complication arises in the case of ß AgZn. The disordered body-centered cubic structure exists above 280°C. On quenching from above this temperature an ordered structure of the cesium-chloride type is formed. On slow cooling, however, a complex hexagonal structure, the 3 phase, is produced; and if an ordered quenched alloy is reheated the phase begins to form above 80°C. It is thus difficult to study local order by X-ray methods in single crystals of AgZn since the C phase formed on heating does not necessarily return to a single crystal of the original orientation. This problem has been met, however, by adding a few percent of gold to the AgZn. The gold suppresses the formation of the c

Jan 1, 1952

By Marshall B. Standing, Donald L. Katz

DENSITY data are reported on 16 saturated hydrocarbon vapors at pressures ranging from 1000 to 8220 lb. per sq. in. and at temperatures ranging from 35° to 250°F. These data have been used to extend the compressibility-factor chart for natural gases up to 10,000 lb. per sq. in. The relatively large quantity of high-boiling constituents present in high-pressure vapors in equilibrium with crude oils makes it necessary to include in the analysis of the gas the molecular weight, density, and possibly boiling range of the heptanes and heavier fraction. Relationships have been presented by which the density of gases may be obtained directly from the temperature, pressure, and gas gravity provided the gases have a common source or are similar in composition. INTRODUCTION The densities of natural gases are necessary in many engineering computations in petroleum production and utilization. Gas reserves, changes in reservoir pressure, gradients in gas wells, metering of gases, pipeline flow, and compression of gases are typical problems requiring the density of the gas. A decade ago, engineering computations used ideal gas laws with deviations up to 500 lb. per sq. in.4 Recent discoveries of pools having pressures up to 7500 lb. per sq. in., and installation of pressure-maintenance and recycling plants, have increased the need for data on gas density at high pressures. METHODS OF COMPUTATION The accepted method of computing the density or specific volume of natural gases is the use of the ideal gas law corrected by a compressibility factor. The method proposed by Kay7 of correlating compressibility factors for gaseous mixtures on pseudocritical properties5 appears to be satisfactory for natural gases.2 The methane-compressibility factor has been shown to deviate systematically from the behavior of natural gases2 and a chart giving these corrected factors is available. A method of computing specific volume of gaseous mixtures from partial molal volumes has been reported by Sage and Lacey.8 Complete data for the computation are not yet available for all hydrocarbon gases. Most of the reported data on gas densities have been in the single-phase region removed from the dew point or saturation condition. Since most gases in the reservoir or while on contact with liquid during flow are saturated, the determination of densities under conditions of saturation is particularly important. Although there is no reason to believe that the saturated gases differ in behavior from those considerably removed from their dew points, the usual experimental determinations find difficulty on approaching the dew-point conditions. This paper reports the density of 16 saturated gases in equilibrium with crude oils. The relationships developed to compute the density of gases to high pressure&apos; have been modified and enlarged. A simplified method of obtaining gas density is presented in the form of charts, which apply for specific groups of gases.

Jan 1, 1941

By Charles C. Rodd

Prior to 1938, proration procedure in Kansas required the physical testing of wells in order to set up a basis for allocating production. Subsequently the use of liquid-level data and bottom-hole pressure data was authorized on certain types of wells as a basis for calculating well capacities, thereby permitting wells to be tested at low rates and with small volumes of production. This paper gives some attention to the equipment used for obtaining liquid-level data but in general it is devoted to the theoretical and physical factors involved in well testing by drawdown methods. These tests are divided into two classifications: (I) liquid-level data used directly to calculate capacities, and (2) liquid-level data and liquid-level measuring equipment used in connection with other data to determine bottom-hole pressure. Equations and calculations for both types are shown. Well capacities calculated from fill-up data have not been used generally but offer a simple means of testing some wells. Theoretical factors and calculations for such tests are shown. In the state of Kansas, proration laws required that the "ability of a well to produce" be given consideration in state allocation orders and for many years this was the only factor used in prorating the allowed oil. The "ability of a well to produce", was the quantity of oil that could be obtained from a well in a prescribed period, usually 24 hr. Early in the history of State-regulated proration, Kansas operators realized that, unless some restriction were placed upon equip- ment, the competition between producers to obtain large well "potentials" might result in a race to install the largest pumping equipment. Consequently, restrictions were placed upon the size of tubing and length of pump stroke that could be used in pumping wells during potential tests. Later, restrictions were placed also upon the size of tubing and chokes that could be used in flowing walls. Despite the restriction setup, better pumping equipment was designed and installed, pumps were improved, and various devices were invoked to obtain high rates of production for short periods of time. By 1937 pumping cycles of forty to forty-five 54-in. strokes per minute were not uncommon, and numerous wells had produced at the rate of 3500 bbl. per day for short periods. Such production was far beyond any rate that could be long sustained. Equipment necessary to take "potentials" was several times larger than that needed for normal producing purposes, and repairs and replacements required by the high pumping speeds were excessive. Also, many operators suspected that the high rates of production main tained during &apos;"potential" tests were conducivc to early water encroachment. By 1938 large-scale physical testing of wells in Kansas ended, the use of the bottom-hole pressure gauge had become common, engineers and operators were becoming familiar with the term &apos;&apos;productivity index," and bottom-hole pressure was being used as a factor in allocation in many areas. There were many drawbacks, however, to large-scale use of

Jan 1, 1943

Discussion of the paper of HOWARD N. EAVENSON, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 94, October,&apos; 1914, pp. 2637 to 2660. GEORGE S. RICE, Pittsburgh, Pa.-I think it is very wise to point out the greater liability to explosions in certain parts of the year, if there be such difference, with the caution, however, that vigilance be not relaxed at other times. In comparing the figures for the United States with those of Europe, I think we should separate them as far as possible according to cause of origin and means of propagation. That is to say, it would appear to me that the majority of our explosions are due more directly to the ignition of coal dust directly from the flame of explosives, whereas, judging from my inquiries and observations in some of the mines of Europe, the majority of their explosions have been caused by the ignition of fire damp. Now, in the case of fire damp, I do not think that anybody has yet attempted or has been able to find any connection between the seasons and the issuance of methane into mines. One thing must be borne in mind, that if you get a strong explosion of fire damp, dust of a character that might not ignite readily by itself might assist in the extension of an explosion of fire damp through a considerable area in the mine, if not throughout the mine. While it is true we have many lesser explosions in this country attributable to fire damp, it would appear that the majority of all the mine explosions of the country, in considering the means of propagation beyond the locality of the origin, are due to coal dust; and it is the liability to coal-dust explosions that appears to be affected by seasonal changes. Hence the desirability of separating statistically (if it could be done by the inspectors) fire-damp explosions from coal-dust explosions, in order to obtain the true value of the seasonal effect. Nevertheless, in spite of the inclusion of fire-damp explosions with coal-dust explosions, the preponderance of the evidence, as indicated in Mr. Eavenson&apos;s figures for American mines, has shown that&apos; in this country there were more explosions in the winter and spring months, when the mines are drier; that is, when the mines are apt to be drier. Whereas, according to the European figures that he has gathered, it seems to be very clearly demonstrated that in France, England, and Belgium, the time when explosions occur has no connection with any particular season. That, I think, is partly due to the point just mentioned, that a majority of their explosions have originated from fire damp. The European mining men have been more careful, generally speaking, with the use of explosives than we have, so that the cause of ignition from that source has been less. Only comparatively few of the mines in foreign

Jan 4, 1915

By F. W. Rols-Hausen, F. W. Jessen

It is the purpose of this paper to present data on brines occurring in the Frio formation of the Texas Gulf Coast, and to show how their composition varies, (1) with depth below the surface, (2) with depth below the top of the formation, and (3) along the approximate strike. The brines vary in chloride content from 3,180 to 73,000 p.p.m., though the average salinity of the salt waters is shown to vary with total depth; the concentration being 35,000 to 40,000 p.p.m. at 3500 to 5500 ft., slightly less than 50,000 p.p.m. chloride at 5500 to 6500 ft. and average 38,000 to 40,000 below 6500 feet. From the analyses available, it appears that the highest concentration of salts occurs in the upper 300 ft. of the formation, while lower salinity is found with increasing depth below this point. The salt waters from wells in Starr County show less concentration of dissolved salts than in any other group of wells farther north along the strike. In all, 116 analyses from 63 fields and 14 wildcats, from depths ranging from 1300 to 11,400 ft. below the surface and from z to 3240 ft. below the top of the Frio, are recorded. Introduction Brines have been studied for many Years in an attempt to solve some of the geologic and production problems associated with the production of oil and gas. One practical application of study of . water analyses is the correlation of waters occurring above, in, or below the producing sand in the same field or throughout the same formation. The Frio formation, the series of sands and shales occurring below the Marginulina zone and above the Vicksburg, is one of the major oil and gas-producing formations in the Texas Gulf Coast. Fossils are rare or absent in the upper Frio throughout most of the area. When available, cuttings and cores, and electric logs were used to determine the top of the Frio. A change in lithology was used to determine this point in most of the wells, and fossils were used in some of the deep wells. It is realized that a change in lithology is not perfect for correlation purposes over long distances and some of the trends may be influenced by the inability to differentiate between the nonfossiliferous Marginulina zone and the Frio. It underlies virtually all the area shown on the accompanying map (Fig. I). Although it is not productive in the updip facies, it has been explored to a limited degree below I2,000 ft. Further more, toward the coast line future drilling to deeper depths should encounter this formation. Although thousands of wells have penetrated or drilled entirely through the formation, very few water samples have been secured from the many sands occurring in this formation and analyzed. Previous Investigation No previous published study has been made of the chemical composition and concentration of waters from the Frio formation. However, one water analysis

Jan 1, 1944

By H. W. Schadler

Single crystals of tungsten, which were grown by electron bombardment floating zone refining, were strained 2 pet in tension and bending at 298°, 77°, and 20°K to determine the modes and crystallography of the plastic deformation of these temperatures. At 77° and 20°K plastic deformation occurs by slip on systems of the type (011) [111] and by twinning on (112)-type planes. For crystals strained at 298°K, deformation occurs by slip in [111] directions on either (Oil)- or (112)-type planes. CURRENT models for the initiation of brittle fracture in crystalline materials are based on a knowledge of the details of their plastic deformation.1 Body-centered cubic tungsten exhibits brittle failure at temperatures below about 500 °K yet the modes and crystallography of its plastic deformation have not been studied below 1000°K. In 1924, Goucher2 reported that tungsten single crystals with a total impurity content of less than 0.01 wt pet deformed by slip on the (112) [111] system in the temperature range 1000° to 3000°K. He also observed (001) [010] slip in one crystal which was constrained by the presence of a large fissure. According to Barrett3 tungsten also deforms by twinning on the (112) plane in the [111] direction, but he gives no details on the tendency for twin formation or the temperature range in which twinning occurs. Therefore, as a necessary part of a study of the factors influencing the brittle fracture of tungsten, the modes and crystallography of the plastic deformation were determined at 298°, 77°, and 20°K. Tungsten single crystals, grown using the electron-bombardment zone-refining technique first described by Calverly,4 were deformed to between 1 and 2 pet plastic strain in tension and bending. The surface offset resulting from slip or twinning was observed with an optical microscope to determine the crystallography of the deformation. The existence of twins was proven by the standard polishing and etching technique; and the crystallography of dislocation motion was followed using the dislocation etchant described by Wolff.5 Some observations on the fracture characteristics of tungsten single crystals are included. EXPERIMENTAL TECHNIQUES Growth, Purity, and Perfection of the Crystals-Several years ago Calverly, Davis, and Lever4 dem-onstrated the feasibility of growing tungsten single crystals by the electron-bombardment floating zone-refining technique, and Carlson6 showed that crystals produced in this way had a high degree of purity and were ductile at room temperature. Tungsten single crystals produced by this technique in equipment similar to that described by Carlson were used in this study. The starting material, a powder metallurgy product, was obtained in the form of a swaged 1/8-in. rod from the General Electric Wire Plant in Cleveland, Ohio. The crystals were grown from this material in a vacuum of 10"4 mm of Hg by passing a molten zone 1/8 in. long down the rod twice at a speed of 3 mm per min. At this zone speed

Jan 1, 1961

Secretary Membership Committee Increase of Membership Papers and Publications Committee Library Committee Treasurer Report of the Secretary TO THE BOARDOF DIRECTORASN D THE MEMBEROS F THE AMERICANIN STITUTE OF MINING AND METALLURGICAENL GINEERS GENTLEME:N As will be shown by the special reports of the Finance, Membership, Library, Papers and Publications, Increase of Membership, and other standing Committees, together with that of the Treasurer, the year 1927 was one in which the Institute made very satisfactory progress in a number of directions. In total numbers the membership is no larger but in revenue from dues there has been a marked increase. This has been due to the promotion to full membership of Junior Associates of earlier years, to the larger proportion that come in originally as members rather than juniors, and to the keener interest in the work of the Institute reflected in prompter payment of dues. The latter is important, since experience shows that of those who fall behind a large number must ultimately be dropped for non-payment. Conditions in the mining industries have been healthy though not booming. It has been much easier for members to find employment and meet their financial obligations but there has not been that flow of young men into mining, and hence in part into the Institute, that characterized certain earlier years. Rather the tendency toward centralization and larger industrial units has restricted the number, though not the scope, of opportunities for technical men in the mineral industries. The Institute is constantly receiving resignations from members crowded out of mining into other lines of activity. On the other hand, those who remain in mining and metallurgy have a greatly increased necessity for i,dormation and contacts with technology. A few years ago many superintendents and most foremen were non-technical men. Today the reverse rule obtains and shift bosses and men who occupy even lower positions in industrial units are called upon to know and to apply such an amount of technical knowledge that graduate engineers are the rule rather than the exception. The curious situation has obtained that with a much smaller enrolment of students in the schools of mining and metallurgy there has been at times an actual shortage of young engineers for beginners&apos; jobs. The young men retort that the conditions of employment and pay offered in mining are not equal to those in other lines and, while it is undoubtedly true that the young engineer beginning in mining is able to start under conditions markedly better as to pay, living, and responsibility than did the men who are now leaders, they are required to know much more and have usually spent more in time and money to qualify for their jobs. The whole matter is one which warrants much more attention than has been given to it. For the Institute it is important since the young men

Jan 1, 1928

By Andrew B. Crichton

THE oft repeated statements of the United States Geological Survey and the Bureau of Mines that the coal reserves in the United States are sufficient for 3000 yr have given us all a sense of security hard to disturb. If we discount that statement 66 pct, which to the uninformed seems drastic, we would still have 1000 yr supply, and why should mortal man worry about the difference between 1000 and 3000 yr supply of coal. That is exactly the attitude which many who should be better in- formed have taken toward the problem. A recent brochure "How Strong is America," by the New York Herald Tribune, states there is "no end to coal * * The truth is staggering * * U. S. has enough coal to last 4000 years." What the statement actually means is that the calculator got as high as 4000 yr and decided it was pointless to go on. The President&apos;s ERP Committee on Natural Resources and others in high places continue to assure the country of our superabundance of coal. In the past few days the “Wall Street Journal" carried an item from Director Boyd of the Bureau of Mines saying that within a hundred years we would need to triple our annual coal production of 6oo,ooo,ooo tons, making it 1,800,000,000 tons annually, and at that rate we had coal reserves sufficient for 1000 yr. In my humble opinion, we cannot now or ever produce 1,800,000,000 tons annually, be- cause we do not have the reserves in the producing districts to do it. Past reckoning in geology may be, as in the Psalms, a thousand years are as yesterday, but the future must be considered more realistically, and "a thousand years" is really a "heck" of a long time. In most developed areas, mining engineers can count the coal reserves in terms of a hundred years or less, and in some important areas now producing large annual tonnages in much under fifty years. They think when they hear of thousands of years coal reserves, reference is made to distant fields and "the fields are always green far away." The estimates of our coal reserves upon which we are relying were made in 1907 under the direction of Marius R. Campbell, Director of the United States Geological Survey. It is apparent this work was not well done. It was necessarily based on rather meager data because of the little development and prospecting as of that date. There were mistakes in the correlation of seams, and they assumed the continuity of thick seams throughout large coal bearing areas where coal often did not exist. The overstatement of coal bearing areas in the Campbell figures are common. The 1907 survey includes all coals over 14 in. in thickness to a depth of 3000 ft. The total coal reserves according to Campbell were 3157.2 billion tons. The production and mining losses that year would amount to -570 million tons and

Jan 1, 1948

By D. H. Turner, F. A. Crossley

The titanium-rich corner of the system Ti-Al-Si has been studied to determine the phase relationships in the temperature interval 600° to 1200°C. Metallographic examination of long time isothermally annealed specimens was the means of investigation. PART of a program on phase relations and transformation processes of titanium alloy systems included the study of the titanium-rich corner of the Ti-Al-Si system. The investigation covered ternary compositions in the range 2 to 8 pet A1 and 0.1 to 2 pet Si and binary compositions in the range 0.2 to 2 pet Si. Temperatures were in the range of 600" to 1200°C. Alloys containing 6 pet A1-0.1 to 0.5 pet Si were investigated down to 400°C. Partial vertical sections are presented for 2, 4, 6, and 8 pet Al. The Ti-Si system has been reported by Hansen et al.&apos; It is characterized by a eutectoid decomposition, ß = ± a + Ti3Si3, at 860°C. The maximum solubility of silicon in a is reported to be about 0.5 pet at the eutectoid temperature. The solubility of silicon in 0 increases from 0.9 pet at the eutectoid temperature to approximately 3 pet at the eutectic temperature, 1330°C. Several investigations in the composition range of interest have been reported for the Ti-A1 system."&apos; These investigations are in agreement on the phase fields, but differ to small extents on boundary positions. However, very recent, and as yet unpublished, findings" " indicate that there are perhaps two phases which occur at lower aluminum contents than the ? (TiA1) phase, and that the solubility of aluminum in a titanium is less than 6 pet. In the present investigation phase relations found are in agreement with the published literature exemplified by the work of Bumps et al.3 Therefore, it is probable that the partial system reported herein is metastable and does not represent true equilibrium. Experimental Procedure High purity Bureau of Mines titanium sponge of 103 Bhn hardness, granulated aluminum shot of 99.7 pet purity, and silicon powder of 99.8 pet purity were used in making the alloys. For the work in the range from 600" to 1200°C, 100 g ingots were prepared by arc melting. Melting losses were negligible and spot checks by chemical analysis showed good agreement between nominal and analyzed results. Nominal compositions are used throughout this paper. Ingots were forged to 3/8 in. rounds and cut into specimens for heat treatment. Isothermal anneals in the range from 600" to 900°C were preceded by solution treatment at 1000°C for 1 hr, followed by furnace cooling to the annealing temperature. Samples were sealed in evacuated Vycor bulbs for heat treatments up to 1000°C. Higher temperature anneals were done with the samples sealed in quartz bulbs under a partial pressure of argon.

Jan 1, 1959

By F. W. Jessen, F. W. Rols-Hausen

It is the purpose of this paper to present data on brines occurring in the Frio formation of the Texas Gulf Coast, and to show how their composition varies, (1) with depth below the surface, (2) with depth below the top of the formation, and (3) along the approximate strike. The brines vary in chloride content from 3,180 to 73,000 p.p.m., though the average salinity of the salt waters is shown to vary with total depth; the concentration being 35,000 to 40,000 p.p.m. at 3500 to 5500 ft., slightly less than 50,000 p.p.m. chloride at 5500 to 6500 ft. and average 38,000 to 40,000 below 6500 feet. From the analyses available, it appears that the highest concentration of salts occurs in the upper 300 ft. of the formation, while lower salinity is found with increasing depth below this point. The salt waters from wells in Starr County show less concentration of dissolved salts than in any other group of wells farther north along the strike. In all, 116 analyses from 63 fields and 14 wildcats, from depths ranging from 1300 to 11,400 ft. below the surface and from z to 3240 ft. below the top of the Frio, are recorded. Introduction Brines have been studied for many Years in an attempt to solve some of the geologic and production problems associated with the production of oil and gas. One practical application of study of . water analyses is the correlation of waters occurring above, in, or below the producing sand in the same field or throughout the same formation. The Frio formation, the series of sands and shales occurring below the Marginulina zone and above the Vicksburg, is one of the major oil and gas-producing formations in the Texas Gulf Coast. Fossils are rare or absent in the upper Frio throughout most of the area. When available, cuttings and cores, and electric logs were used to determine the top of the Frio. A change in lithology was used to determine this point in most of the wells, and fossils were used in some of the deep wells. It is realized that a change in lithology is not perfect for correlation purposes over long distances and some of the trends may be influenced by the inability to differentiate between the nonfossiliferous Marginulina zone and the Frio. It underlies virtually all the area shown on the accompanying map (Fig. I). Although it is not productive in the updip facies, it has been explored to a limited degree below I2,000 ft. Further more, toward the coast line future drilling to deeper depths should encounter this formation. Although thousands of wells have penetrated or drilled entirely through the formation, very few water samples have been secured from the many sands occurring in this formation and analyzed. Previous Investigation No previous published study has been made of the chemical composition and concentration of waters from the Frio formation. However, one water analysis

Jan 1, 1944

By W. N. Lacey, B. H. Sage

THE results of an extensive experimental program relating to the effectiveness of gravel screens have been correlated. The factors considered in some detail include gravel size and condition of packing, sand size and size distribution, fluid velocity, fluid viscosity, and thickness and arrangement of gravel screens. Good agreement between calculated values based upon probability considerations and experimental results relating to the influence of the thickness of the gravel screen was obtained. All of these factors are treated in the correlation in order that their influence may be taken into account in ascertaining the characteristics of an effective gravel screen for a particular set of conditions. The details of the experimental program are not given in the present paper but a description of generalized behavior and typical experimental results are recorded in graphic form. INTRODUCTION Gravel screens have been placed in water and oil wells for a number of years1,2,3 with the dual objective of increasing the productivity and decreasing the entrance of sand into the well bore. An understanding of the factors controlling the effectiveness of gravel screens in this connection is of industrial interest because it will lead to the proper selection of gravel. Some of the fundamental considerations involved in the migration of sand through a coarser body of porous materials were investigated by Coberly and Wagner4 and further experimental work has been carried out by Gumpertz.5 Apparently the pertinent phenomena are somewhat complex and are influenced by many variables. The present paper deals with the prediction of the behavior of gravel screens under the conditions encountered in practice but does not attempt to discuss the experimental methods or results that were obtained as a background and upon which the prediction is based. INFLUENCE OF GRAVEL SCREENS UPON PRODUCTIVITY The use of a gravel screen may increase the productivity of a well by increasing its effective diameter, and this constitutes one of the objectives of its use. The permeability of most gravels and coarse sands that are employed in practice is so large compared to that of the sand in place that relatively little loss in production rate will arise from the use of material fine enough to cause the desired resistance to sand migration. For example, in Fig. I is depicted the approximate variation in the permeability of closely sized spherical gravels under the conditions of packing likely to be encountered in screens. The dotted lines indicate the variation that might be found because of differences in packing. It should be realized that the permeability is not a single-valued function of the. average grain diameter but is related to a large number of factors, including the size, the size distribution and the shapes of the particles. However, Fig. I does permit a rough estimation of the permeability of closely sized- spherical gravels and shows that the permeability with even the smaller particles is very large compared to that of most petroleum production horizons.

Jan 1, 1941

By J. D. Hanawalt, C. E. Nelson, J. A. Peloubet

THE subject of the salt-water corrosion resistance of magnesium alloys is somewhat like that of the pitting of stainless steels, in that it involves a relatively small percentage of the applications but receives a much greater proportion of the publicity. Actually magnesium alloys are in use in many exterior applications as well as interior, with no trouble from corrosion. Magnesium and its alloys have a striking stability against atmospheric attack, being far superior to iron. Specimens exposed unprotected to atmospheric weathering for 10 years show only a superficial surface-film formation. The basic nature of magnesium and of its important alloys is that they are also resistant to the attack of salt water even in an unprotected state, giving substantially no loss in weight after one year of alternate immersion in 3 per cent NaCl solution (Fig. I). This basic behavior is often masked because of the extreme sensitivity of these alloys to certain impurities and combinations of impurities. It is known, and the subject of increasing emphasis, that higher purity leads generally to greater stability for many materials, nonmetallic as well as metallic. However, a review of the literature on the corrosion factors in magnesium alloys shows that almost all researchers worked with base metal in which metallic impurities varied in uncontrolled amounts. The major factor, that of metallic impurities, probably greatly overshadowed the effects of minor ones such as flux inclusions, nonmetallic impurities, porosity, metallographic state, which these researchers presumed to study. In the present investigation the first observation of interest is that whereas magnesium of commercial purity (99.9 per cent pure) has a corrosion rate in alternate immersion in 3 per cent NaCl solution at room temperature of anywhere from 5 to 100 mg. per sq. cm. per day, the corrosion rate of high-purity magnesium is 0.15 ± 0.05 mg. per sq. cm. per day. The principle followed in the experiments was to add to such base magnesium other elements, singly and in combination, in controlled and known amounts and to observe the corrosion behavior of the resulting alloy. These experiments show the existence of what may be called "tolerance limits" of magnesium and some of its alloys for certain impurities. The extremely small percentages of impurities involved and the sharpness of the corrosion discontinuities appear to be quite unpredictable. In order to carry on this work, it was necessary to develop an analysis technique suitable to the problem. In some cases it was necessary quantitatively to analyze impurities to less than 0.001 per cent. The experimental data to be presented are based on observation of about 5000 alloy specimens and on more than 50,000 quantitative analyses. While the primary purpose of this paper is to present the experimentally obtained data on corrosion rates as a function of composition, and particularly to demon-

Jan 1, 1941

By M. R. Tek, K. H. Coats, D. L. Katz

A large number of boundary value problems encountcred in unsteady-state heat transfer, fluid flow through porous media, neutron diffusion and mass transfer involve the solution of a linear, parabolic partial differential equation commonly refcrred to as the diffusivity equation, where U is the dependent potential variable. K is the diffusivity (hydraulic, thermal, neutron, etc.) and 1 is the time variablc. Solutions to Eq. I are available in the literature for a wide variety of initial and houndary conditions. The great majority of these solutions are ohtained for geometric boundaries corresponding to linear. cylindrical or spherical flow models. A typical engineering application where the solution to Eq. 1 is required is the calculation of underground water encroachment across the boundaries of oil or natural gas reservoirs, In this particular area of application, the reservoir boundary is invariably approximated by circular geometry. However. the areal shape of many reservoirs can be better approximated by elliptic rather than circular boundaries. Thus the need for a general method of solving the diffusivity equation in elliptic coordinates arises in this problem as well as in other engineering applications involving elliptic boundaries. The solution to the diffusivity equation usually in volves the Error Function for the linear flow model, Bessel functions for the radial flow model and trigonometric or Legendre functions for the spherical flow model. It is well known that the general solution to the diffusivity equation in elliptic coordinates involves Mathieu functions. The significance of Mathieu functions in the analytical treatment of the diffusivity equation in elliptic coordinates is discussed in the literature However, these references do not providc analytical solutions useful in practical engineering problems. The objectives of this papcr are the development of the equations describing the unsteady-state liquid flow through a porous medium with an elliptic inner boun- dary, the development of a numerical method of solving these equations and, finally, a comparison of the water encroachment quantities calculated from the elliptic flow equation with those calculated from the radial flow equation. While the specific problem treated in this paper relates to unsteady-state liquid flow through a porous medium, the basic equations and computational techniques devcloped will apply equally well to problems occurring in the other areas of engincering interest mentioned previously. The solution given here is limited to a single case in which thc outer boundary encloses an area 100 times that of the inner boundary. DESCRIPTION OF THE FLOW MODEL Fig. 1 shows the flow model upon which the calcu lations presented in this paper are based. The inncr and outer houndaries of the flow model are represented by two confocal ellipses with major and minor axes, respectively, equal to 2a1, 2b1, and 2a, and 26,. The height of the elliptic cylinder flow model is denoted by 17. The following assumptions are employed in the development 01 the equations governing the unsteady-state liquid flow through the described flow model. 1. Uniform porosity and permeability throughout the flow model