Search Documents

By M. R. Hatfield, F. J. Vosburgh

In a recent article, it was shown that in the blast furnaces in Germany that are lined with carbon blocks no cooling plates are used, and that shower cooling is employed on the hearth and bosh sections. While one of the authors was in Germany he was told that one furnace was being operated without even the shower cooling on the bosh section, though the hearth section was shower-cooled. In discussion of this interesting situation with a number of blast-furnace operators in this country, it was made clearly and promptly evident that shower cooling was very unpopular, probably because of its messiness and its ineffectiveness. Both of the causes for the dislike of shower coolings are reasonable ones. Shower cooling can be and frequently is messy, but the present cooling of blast furnaces leaves much to be desired on that score. Shower cooling is ineffective as compared with plate cooling, so far as its usefulness in keeping the bricks cool enough not to melt or fall to pieces is concerned. However, the introduction of carbon linings changes the situation. No one is concerned with keeping a carbon lining cool, for no temperature in the blast furnace has any effect on carbon, which is just as stable at 3000°F. as it is at 70°F. The only concern is for the shell—to keep it cool enough for safety and comfort— and for that shower cooling is sufficient. Of course, with only the shell to cool, instead of the shell plus all the refractory material, much less water would be required, and the necessity for constant attention to the flow would be lessened, as the hundreds of inlets and outlets would be eliminated. Probably half of the water used in cooling a blast furnace is used for cooling the shaft and tuyeres and the remainder for the bosh and hearth sections. However, in view of the dislike of shower cooling in the United States, and particularly because at least one German blast furnace is operated with no cooling of the bosh section, thought was given to the possibility that a carbon-lined blast furnace might be operated without any cooling of the entire carbon-lined portion. For that reason a series of experiments was performed to determine what might be the temperature of the shell of a blast furnace protected by a carbon lining and operated under varying conditions up to a maximum inside temperature of 3000°F. Experimental Procedure A schematic diagram of the experimental setup is shown in Fig. I and a photograph of the entire assembly in Fig. 2. The heating element was a a tubc nominally 25/8 in. 0.d. by 2 in. i.d. by 30 in., used as a resistor. Power was furnished by a I5-kva. transformer operating

Jan 1, 1942

By J. C. Cordell, C. F. Weinaug

A study of the behavior of retrograde condensation from gas mixtures was made in the presence and absence of sand in order to determine if the condensed liquid would re-vaporize in the Presence of sand. Methane-butane and methane-pentane mixtures that would form liquids by retrograde condensation when produced from a constant volume cell were used. The methane-butane mixtures of similar composition were produced by three different methods. The first two were charged into an empty cell and were produced in one case within a period of 9 hr and in the other within a period of 3 days. The third mixture was charged to a sand-packed cell and produced within a period of 9 hr. The curves relating composition of the produced gas to pressure obtained from these experiments show that equilibrium was maintained as long as liquid was condensing. However, during the portion of the pressure decline where the condensed liquid should be revaporizing, equilibrium was maintained only when the mixture was produced from the sand-packed cell. The methane-pentane mixture is produced only in the presence of sand. The data obtained for this system also show that equilibrium is maintained at all times during the pressure decline. These results indicate that revaporization is aided rather than prevented by the fact that the condensate "wets the sand." The significance to the petroleum industry of the behavior of hydrocarbons in the retrograde region is becoming increasingly important because a large percentage of reservoirs being discovered today arc of the gas-condensate type. The important characteristic of a gas-condensate reservoir is the retrograde condensation of a liquid phase throughout the reservoir if the pressure is allowed to decline. In order to prevent the loss of this retrograde liquid in some of these reservoirs, they are "cycled"; that is, the material produced from the reservoir is processed to remove the heavier hydrocarbons and the light fractions are returned to the reservoir to maintain the reservoir pressure. Another method of producing these reservoirs is Pressure depletion. There are other methods but they are not in general use. Although a large number of factors are involved in determining the optimum method of producing a reservoir, only the problem of whether the retrograde condensate resulting from pressure depletion will revaporize from sand at equilibrium conditions is considered in this paper. Also the data are limited to the methane-n-butane and the methane-n-pentane systerns at loo°F and one type of sand. Three types of tests were run in order to compare the revaporization of retrograde liquid formed in a cell with that formed in a sand-packed cell, and to establish the effect of time. The results of tests presented in this paper indicate that both time and the presence of sand promote the revaporization of

Jan 1, 1949

By M. R. Hatfield, F. J. Vosburgh

IN a recent article,† it was shown that in the blast furnaces in Germany that are lined with carbon blocks no cooling plates are used, and that shower cooling is employed on the hearth and bosh sections. While one of the authors was in Germany he was told that one furnace was being operated without even the shower cooling on the bosh section, though the hearth section was shower-cooled. In discussion of this interesting situation with a number of blast-furnace operators in this country, it was made clearly and promptly evident that shower cooling was very unpopular, probably because of its messiness and its ineffectiveness. Both of the causes for the dislike of shower coolings are reasonable ones. Shower cooling can be and frequently is messy, but the present cooling of blast furnaces leaves much to be desired on that score. Shower cooling is ineffective as compared with plate cooling, so far as its usefulness in keeping the bricks cool enough not to melt or fall to pieces is concerned. However, the introduction of carbon linings changes the situation. No one is concerned with keeping a carbon lining cool, for no temperature in the blast furnace has any effect on carbon, which is just as stable at 3000°F. as it is at 70°F. The only concern is for the shell-to keep it cool enough for safety and comfort and for that shower cooling is sufficient. Of course, with only the shell to cool, instead of the shell plus all the refractory material, much less water would be required, and the necessity for constant attention to the flow would be lessened, as the hundreds of inlets and outlets would be eliminated. Probably half of the water used in cooling a blast furnace is used for cooling the shaft and tuyeres and the remainder for the bosh and hearth sections. However, in view of the dislike of shower cooling in the United States, and particularly because at least one German blast furnace is operated with no cooling of the bosh section, thought was given to the possibility that a carbon-lined blast furnace might be operated without any cooling of the entire carbon-lined portion. For that reason a series of experiments was performed to determine what might be the temperature of the shell of a blast furnace protected by a carbon lining and operated under varying conditions up to a maximum inside temperature of 3000°F. EXPERIMENTAL PROCEDURE A schematic diagram of the experimental setup is shown in Fig. I and a photograph of the entire assembly in Fig. 2. The heating element was a carbon tube nominally 2 5/8 in. o.d. by 2 in. i.d. by 30 in., used as a resistor. Power was furnished by a 15-kva. transformer operating

Jan 1, 1941

By M. R. Hatfield, F. J. Vosburgh

In a recent article, it was shown that in the blast furnaces in Germany that are lined with carbon blocks no cooling plates are used, and that shower cooling is employed on the hearth and bosh sections. While one of the authors was in Germany he was told that one furnace was being operated without even the shower cooling on the bosh section, though the hearth section was shower-cooled. In discussion of this interesting situation with a number of blast-furnace operators in this country, it was made clearly and promptly evident that shower cooling was very unpopular, probably because of its messiness and its ineffectiveness. Both of the causes for the dislike of shower coolings are reasonable ones. Shower cooling can be and frequently is messy, but the present cooling of blast furnaces leaves much to be desired on that score. Shower cooling is ineffective as compared with plate cooling, so far as its usefulness in keeping the bricks cool enough not to melt or fall to pieces is concerned. However, the introduction of carbon linings changes the situation. No one is concerned with keeping a carbon lining cool, for no temperature in the blast furnace has any effect on carbon, which is just as stable at 3000°F. as it is at 70°F. The only concern is for the shell—to keep it cool enough for safety and comfort— and for that shower cooling is sufficient. Of course, with only the shell to cool, instead of the shell plus all the refractory material, much less water would be required, and the necessity for constant attention to the flow would be lessened, as the hundreds of inlets and outlets would be eliminated. Probably half of the water used in cooling a blast furnace is used for cooling the shaft and tuyeres and the remainder for the bosh and hearth sections. However, in view of the dislike of shower cooling in the United States, and particularly because at least one German blast furnace is operated with no cooling of the bosh section, thought was given to the possibility that a carbon-lined blast furnace might be operated without any cooling of the entire carbon-lined portion. For that reason a series of experiments was performed to determine what might be the temperature of the shell of a blast furnace protected by a carbon lining and operated under varying conditions up to a maximum inside temperature of 3000°F. Experimental Procedure A schematic diagram of the experimental setup is shown in Fig. I and a photograph of the entire assembly in Fig. 2. The heating element was a a tubc nominally 25/8 in. 0.d. by 2 in. i.d. by 30 in., used as a resistor. Power was furnished by a I5-kva. transformer operating

Jan 1, 1942

By R. A. Bell, R. Schultz, P. G. Hallof

The Ballyvergin area is located in County Clare on the southwest coast of Ireland. It is one of six areas in County Clare in which mining operations were carried out during the last century. The ores mined were high grade Cu-Pb-Ag deposits in the form of small fracture fillings and gash veins in the lower Carboniferous limestones. The zone of primary economic interest is situated on the north limb of a geosyncline which plunges moderately to the southwest. The zones of mineralization previously mined were associated with local structures and folds, and the initial geophysical investigations took the form of reconnaissance induced polarization measurements around, and between, the old mines. This work located an anomaly which, on drilling, resulted in a small extension of the Pb-Cu ore at the Ballyvergin mine. However, a potentially more important zone of mineralization resulted from the drilling of another IP anomaly near Ballyvergin. This wide anomaly was found to be a domal shaped deposit of disseminated chalcopyrite located at a depth of more than 100 ft. The deposit is controlled by local folding in the sediments and is of a type previously unknown in the area. More IP investigations are under way to locate other deposits of the same type. The Ballyvergin area is located in County Clare, about 35 miles northeast of Shannon Airport, near the Atlantic west coast of Southern Ireland (Fig. 1). Interest in the area stems from a number of occurrences of small, but high grade, Pb-Ag deposits. From the summer of 1960 to the spring of 1961, Irish Base Metals carried out a comprehensive exploration program on a 38-sq mile concession in east-central County Clare in an attempt to locate additional deposits of this type. Field operations consisted of geologic mapping, geochemical soil and stream sampling, geophysical surveying and diamond drilling. The geophysical program consisted primarily of detailed induced polarization (IP) surveys in the general vicinity of old mine workings, supplemented by electromagnetic and self-potential investigations. Subsequent diamond drilling of a well defined IP anomaly close to the old Ballyvergin mine disclosed a sizeable deposit of low grade disseminated copper, a type of deposit previously unknown in this area. REGIONAL GEOLOGY Topography: The topography is of the Karst type with low regional relief. The northern parts of the area are covered almost completely with glacial deposits including a large number of drumlins. Elsewhere the overburden is patchy and only moderately deep. A close network of roads makes every part of the area readily accessible, and rail and harbor facilities are available nearby — Fig. 2. Stratigraphy: The area was mapped on a reconnaissance basis by the Geological Survey of Ireland during the latter part of the 19th century at scales of 1 and 6 in. to the mile. Mapping is complicated in

Jan 1, 1962

Discussion of the papers of Dorsey A. Lyon and Samuel S. Arentz, p. 789; S. E. Bretherton, p. 802; H. A. Wentworth, p. 809; and Richard D. Drvine, p. 814. GeoRge W. RiteR, Salt Lake City, Utah.—We have every reason to believe that oil flotation will soon come into general use as a final guard against slime losses in concentrating mills, not only in the case of zinc ores, but also in the case of other semi-precious ores. It also promises much as a primary process for the concentration of minerals that are not adapted to gravity methods. Moreover, modifications of the process involving selective or preferential flotation are gradually becoming understood, and will make it possible to eliminate pyrite and other minerals occurring as undesirable impurities in zinc concentrates. And what perhaps is of equal importance, further modifications promise an effective method of separating zinc blende from ores that are chiefly valuable for copper, lead, and precious metals, thereby making an asset out of zinc which has heretofore been a liability. The tendency of certain pulverized minerals to float on water, especially after having been in contact with grease, has been known to mill-men for a long time, and was formerly something to be deplored and to be striven against. All at once, this tendency has become a saving grace; and now, like tardy converts to a new faith, we are zealous advocates of something we once despised. I was once employed at a mine in the Tintic mining district of Utah— the old Eureka Hill property—where ores that were too low in value to warrant being sent to copper or lead smelters were treated in a combination mill. The ores contained gold, silver, lead, copper, zinc, manganese, arsenic, etc., in varying quantities and in varying mineral forms, mingled in a quartz and calcite gangue. The material was stamped fine and then concentrated on Frue vanners so as to make a smelting concentrate, after which the tailings were thickened and treated in amalgamating pans for the recovery of non-concentratable precious metals. In the amalgamating pans, under the influence of heat and agitation, a dark greasy froth or scum sometimes formed on the surface of the ore mixture. This froth or scum was composed mainly of mineral sulphides, and its occurrence might have meant only casual losses in the previous concentration, except that the phenomenon was accompanied by faulty amalgamation of the precious metals and by excessive losses in the mill tailings. Grease and oil, present by accident, were the cause of the trouble. Whether the intense vibration in the mill, due to the pounding of the heavy stamps, had caused small particles of grease to be shaken loose

Jan 1, 1915

By T. E. Leontis, D. H. Feisel

MAGNESIUM alloys containing rare earth metals have received considerable attention during the past several years because of the need for light alloys having high strength and creep resistance at elevated temperatures. Although much of the work reported earlier has dealt with alloys containing Mischmetal, it has been shown in two previous papersl, V hat distinctly different effects are produced by various rare earth metals and rare earth metal mixtures on the properties of magnesium. For example, much higher strengths are obtained in magnesium alloys containing didym-ium (essentially neodymium plus praseodymium) than in alloys made with Mischmetal, which contains all the rare earth metals in the proportions in which they occur naturally in the monazite ore. Mg-rare earth metal alloys are characterized by a relatively coarse grain size, which greatly impairs castability. The addition of zirconium as a second alloying ingredient has been shown8,7 to refine the grain size, which also produces a distinct improvement in the strength properties. Certain Mg-Mischmetal-Zr and Mg-Mischmetal-Zn-Zr alloy compositions which are currently being produced commercially have been discussed in dytail by Nelson and Strieter,8,4 who also present some in- formation on a Mg-low Ce-Mischmetal-Zr alloy, and by Nelson.8 A patent issued to Jessup, Emley, and Fisher9 emphasizes the superiority of Mg-didymium-Zn-Zr alloys over the corresponding alloys made with Mischmetal. The purpose of this paper is to present the results of an extensive investigation concerned with the effect of increasing amounts of zirconium on magnesium sand casting alloys containing several different rare earth metal mixtures in varying amounts. The effect of the addition of zinc to some of these alloys is also being reported. Preparation and Testing of Alloys The alloys studied in this investigation were prepared in small laboratory melts according to the melting procedures described by Nelson1" as the Crucible Method. Electrolytic magnesium having the composition shown in Table I was used as the starting material. The rare earth metal alloying ingredients used in preparing these alloys were essentially of the compositions listed in Table 11. Some of the didymium-containing alloys were prepared using a Mg-didymium hardener. The rare earth metal content of this hardener analyzed 1.2 pct Ce, 10.4 pct Pr, 80.8 pct Nd, and 7.6 pct La. The zirconium was added in one of three forms: 1) as sponge zirconium obtained from the Bureau of Mines; 2) as a fused salt consisting of 50 pct ZrCl, and 50 pct alkali chlorides from which the zirconium is reduced by the magnesium; or 3) as a Mg-Zr hardener. The alloying procedures and melt hand-

Jan 1, 1958

By A. H. Daane, B. J. Beaudry

The uranium-antimony system has been investigated by metal-lographic, therma1, and X-ray methods. There are four intermediate phases present: USbz and U,Sb, which undergo peritectic decomposition at 1355°and 1695OC, respectively, and USb and UPSbs which melt congruently at 1850"and 1800°C, respectively. There is a eutectic between U4Sbs and USb which melts at 1770°C. USb,, UsSb4, and USb are line compounds while U4Sbs has a solubility range of approximately 1.5 at. pct at 1770°C. Single crystal studies of the cmpo,und U.,SbS show it to have a hexagonal unit cell with a, = 9.268A and c, = 6.201b;. The solubility of uranium in liquid antimony increases from 0.1 at. pct at 650°C to 1.5 at. pct at 900°C. The solubility of antimony in a, P, and y uranium is approximately 0.02, 0.1, and 0.05 at. pct respectively. IN nuclear reactors, uranium has been used mainly in the form of solid-fuel elements of the pure-metal or uranium-rich alloys. However, in attempts to overcome some of the difficulties inherent in solid-fueled reactors, reactor concepts hive been proposed in which the fuel would be a liquid metal, such as a solution of uranium in another metal. The liquid-metal fueled reactor (LMFR) designed by the Brook-haven National Laboratory of the U.S. Atomic Energy Commission is an example. Fuel for this reactor is a solution of approximately 800 ppm enriched uranium in bismuth.' To design such liquid-fueled reactors, a background of information on the solubility of uranium in various metals is obviously necessary. The present study was undertaken to pro- vide information for such purposes, and in addition, to study the uranium-antimony system as a whole. A preliminary literature search showed that some work had been done previously on uranium-antimony alloys, but no attempts had been made to make a complete study of this system. The solubility of uranium in antimony was studied by Cammack and Bridger' up to 950°C and by Hayes and Gordon up to 900'-C. Their data are plotted in Fig. 1. Ferro, in an X-ray structure study of some uranium-antimony compounds, found USg to be tetragonal with a, = 4.2724 and c, = 8.471A, U3S4 to be b.c.c. with aO = 9.095A and USb to be f.c.c. with a,= 6.191A. Colani reported the compound UsSba; however, work by Ferro and by this Laboratory showed that this compound does not exist. foote' reported several intermediate phases in the uranium-antimony system, but did not identify them. Greninger' re-ported finding an intermediate phase in a 5 at. pct Sb

Jan 1, 1960

By William M. Newton, John E. Sherborne

The relation between the properties of electric logs and the fluid used in drilling a well is briefly discussed in this paper, and the fact that the resistivity of the drilling mud and its filtrate can appreciably affect such logs is shown. Apparatus was designed and a procedure established to determine the effect of various factors on the resistivity of drilling mud. Five muds commonly employed in California were tested and the following observations were made: I. The effect of raising the temperature from 80°F. to 180°F. is to decrease the resis-tiviiy of the mud or filtrate approximately 50 per cent. 2. The resistivity of the mud in most cases closely approximates that of its filtrate. 3, The change in the resistivities of muds caused by the addition of chemical is not the same function of the amount of chemical added for each mud. 4. The effect produced by increased sodium chloride content is to reduce markedly the resistivity of the mud and its filtrate. 5. Weighting materials, such as Baroid and limestone, tend to increase the resistivity of drilling mud. 6, Cement and counteracting reagents reduce mud resistivity. Introduction During recent years, the practice of "electrically logging9' a geologic formation by means of a system of electrodes lowered in a well bore has provided data of inestimable value concerning the nature of the sediments penetrated. Thus, it is generally possible, by means of electric logs, to distinguish readily the differences between shales, sandstones, cherts, limestones, and other rock forms. The distinguishing characteristics recorded in this manner have made possible long-range and closely detailed mapping and visualization of deeply buried structures1-5 to a degree not to be obtained with a reasonable expenditure of money by any other means at present in use. Besides being of value in correlation work, electric logs have been found, in some instances, to be useful in estimating the nature of fluid contained within the pores of a rock. In special cases, even the relative permeabilities at different horizons have been determined.6 That electric logs should reflect in some measure such physical properties of rocks as porosity and permeability and, in addition, give rise to data pertaining to the fluid content of rock interstices, becomes evident when the conditions giving rise to the electrical phenomena measured are known. However, it is not the purpose of this paper to review the present status of electric logging; rather, the reader is referred to the papers cited on page 220 for the principles and practice involved. Importance of Drilling FLuid in Electric Logging Because the drilling fluid must be the medium through which the electric logging device is made to traverse the formations penetrated by a borehole, and since, in general, the drilling mud completely surrounds

Jan 1, 1942

By John W. Vanderwilt

The fluorescence of scheelite has been an important aid in recent years in the discovery and development of scheelite deposits. The use of fluorescence of synthetic compounds in industry, particularly in advertising, also has expanded greatly during the past decade. As a result, a number of new and convenient units for producing ultraviolet energy have become available, which have led to a greater application of fluorescence in the study of minerals. Studies have shown that the fluorescent color of a mineral may vary: (I) with the kind and quantity of trace elements, and (2) with the particular wave length of ultraviolet energy used. The wave length is dependent first on the type of generating equipment used, and finally on the filter employed to remove the visible light that may be present. A number of so-called ultraviolet lamps are listed and described, together with suitable filters known to be available. Scheelite fluoresces brilliantly with wave lengths of 2200 to about 3000Å., but not with longer wave lengths. The most convenient and efficient sources of ultraviolet for scheelite fluorescence are portable and laboratory units designed particularly for use with scheelite. So-called ultraviolet light globes of the photo-flood type emit wave lengths too long to cause scheelite to fluoresce. Attention is called to the minerals that fluoresce in a manner similar to scheelite, which necessitates a check test by means of characteristic physical properties. Chemical tests are the final authority both for identity and content of tungsten in scheelite ore. Introduction Recent development and extensive use of fluorescent lighting make it unnecessary to explain what fluorescence looks like. The fluorescent light tube is in reality a mercury vapor arc, which generates ultraviolet energy. Coating the inside walls of the tube is a substance, called a phosphor, that converts the ultraviolet rays to visible rays of light. In a like manner, certain minerals will transform ultraviolet energy to visible rays of various colors. The phenomenon of brilliant fluorescent colors cannot be satisfactorily described or reproduced photographically; a display must be seen to be appreciated. Only a few years ago fluorescence was regarded primarily as a source of entertainment, chiefly in spectacular displays of specimens in museums. The brilliant fluorescence of willemite, a zinc ore mineral, at Franklin, New Jersey, was utilized quite early in checking the efficiency of certain milling operations. Fluorescence has been used extensively in exploring for scheelite, as well as in mining this ore, during the past 10 years. The use of fluorescence in detecting scheelite, an important tungsten ore mineral, is well established, and much success has attended this new method; scheelite is a very inconspicuous white to gray mineral in ordinary light, but it

Jan 1, 1949

By John W. Vanderwilt

The fluorescence of scheelite has been an important aid in recent years in the discovery and development of scheelite deposits. The use of fluorescence of synthetic compounds in industry, particularly in advertising, also has expanded greatly during the past decade. As a result, a number of new and convenient units for producing ultraviolet energy have become available, which have led to a greater application of fluorescence in the study of minerals. Studies have shown that the fluorescent color of a mineral may vary: (I) with the kind and quantity of trace elements, and (2) with the particular wave length of ultraviolet energy used. The wave length is dependent first on the type of generating equipment used, and finally on the filter employed to remove the visible light that may be present. A number of so-called ultraviolet lamps are listed and described, together with suitable filters known to be available. Scheelite fluoresces brilliantly with wave lengths of 2200 to about 3000Å., but not with longer wave lengths. The most convenient and efficient sources of ultraviolet for scheelite fluorescence are portable and laboratory units designed particularly for use with scheelite. So-called ultraviolet light globes of the photo-flood type emit wave lengths too long to cause scheelite to fluoresce. Attention is called to the minerals that fluoresce in a manner similar to scheelite, which necessitates a check test by means of characteristic physical properties. Chemical tests are the final authority both for identity and content of tungsten in scheelite ore. Introduction Recent development and extensive use of fluorescent lighting make it unnecessary to explain what fluorescence looks like. The fluorescent light tube is in reality a mercury vapor arc, which generates ultraviolet energy. Coating the inside walls of the tube is a substance, called a phosphor, that converts the ultraviolet rays to visible rays of light. In a like manner, certain minerals will transform ultraviolet energy to visible rays of various colors. The phenomenon of brilliant fluorescent colors cannot be satisfactorily described or reproduced photographically; a display must be seen to be appreciated. Only a few years ago fluorescence was regarded primarily as a source of entertainment, chiefly in spectacular displays of specimens in museums. The brilliant fluorescence of willemite, a zinc ore mineral, at Franklin, New Jersey, was utilized quite early in checking the efficiency of certain milling operations. Fluorescence has been used extensively in exploring for scheelite, as well as in mining this ore, during the past 10 years. The use of fluorescence in detecting scheelite, an important tungsten ore mineral, is well established, and much success has attended this new method; scheelite is a very inconspicuous white to gray mineral in ordinary light, but it

Jan 1, 1949

Discussions of the papers of DORSET A. LYON and SAMUEL S. ARENTZ, RICHARD D. DIVINE, H. A. WENTWORTH, and S. E. BRETHERTON, presented at the Salt Lake meeting August, 1914, and printed in Bulletins Nos. 91 and 92, July and August, 1914. GEORGE W. RITER, Salt Lake City, Utah.-We have every reason to believe that oil flotation Will soon come into general use as a final guard against slimes losses in concentrating mills, not only in the case of zinc ores, but also in the case of other semi-precious ores. It also promises much as a primary process for the concentration of minerals that are not adapted to gravity methods. Moreover, modifications of the process involving selective or preferential flotation are gradually becoming understood, and will make it possible to eliminate pyrite and other minerals occurring as undesirable impurities in zinc concentrates. And what perhaps is of equal importance, further modifications promise an effective method of separating zinc blende from ores that are chiefly valuable for copper, lead, anti precious metals, thereby making an asset out of zinc which has heretofore been a liability. The tendency of certain pulverized minerals to float on water, especially after having been in contact with grease, has been known to mill-men for a long time, and was formerly something to be deplored and to be striven against. All at once, this tendency has become a saving grace; and now, like tardy converts to a new faith, we are zealous advocates of something we once despised. I was once employed at a mine in the Tintic mining district of Utah¬the old Eureka Hill property-where ores that were too low in value to Warrant being sent to copper or lead smelters were treated in a combination mill. The ores contained gold, silver, lead, copper, zinc, manganese, arsenic, etc., in varying quantities and in varying mineral forms, mingled in a quartz and calcite gangue. The material was stamped fine and then concentrated on Frue vanners so as to make a smelting concentrate, after which the tailings were thickened and treated in amalgamating pans for the recovery of non-concentratable precious metals. In the amalgamating pans, under the influence of heat and agitation, a dark greasy froth or scum sometimes formed on the surface of the ore mixture. This froth or scum was composed mainly of mineral sulphides, and its occurrence might have meant only casual losses in the previous concentration, except that the phenomenon was accompanied by faulty amalgamation of the precious metals and by excessive losses in the mill tailings. Grease and oil, present by accident, were the cause of the trouble.

Jan 11, 1914

By J. M. Seeman, R. A. Dodd

If some solution-quenched supersaturated aluminum solid solutions, e.g.., Al(Cu), are plastically deformed at room temperature and then aged at 200oC, the hardness may first decrease before increasing in the usual manner ' A similar transient softening is observed, even in the absence of plastic deformation, when a thin foil or small-diameter wire Al(Cu) specimen is rapidly quenched from the solution-treatment temperature and then aged.' Also, some solution-quenched and neutron-irradiated alloys undergo an initial hardness decrease during subsequent aging.3 The usual explanation of the transient softening in the above examples involves the effect of vacancies introduced by plastic deformation, rapid quenching, and neutron irradiation, respectively However, the mechanism of softening is not unequivo-cably established. In the first-noted case, Gane and parkins' observed that the softening was approximately proportional to the difference in the atomic diameters of solute and solvent, and it was argued that, if a large relative difference in atomic diameter promoted vacancy-assisted room-temperature solute diffusion to dislocations, dislocation climb occurring during subsequent aging at 200°C could cause transient softening. Some substantiation of this theory was offered by the additional observation that discontinuous yielding of solution-quenched polycrystalline Al(Cu) tensile specimens was suppressed by interrupting the test for a short aging treatment at 200°C. Of course, reversion (resolution of GPI) at 200°C would also cause softening, and Sil-cock4 expressed the opinion that the softening in the case of Al(Cu) must be partly associated with reversion. Also, Hirsch5 commented on the possibility that, if jogs cause hardening, an anneal at 200°C should straighten the jogged dislocations and result in softening. However, parkins' has re-expressed his belief that these mechanisms are not entirely consistent with the observed serrated stress-strain curves. Experimental. New data has now been obtained for Al(Cu), Al(Ge), Al(Mg), and Al(Zn) primary solid-solution alloys. These alloys were prepared from metals exceeding 99.99 pct purity, and specimens 4 by 4 in. diam were solution-treated, quenched, deformed 10 pct in compression at room temperature, and aged at 200'C in a cottonseed oil bath for various times. Generally, these operations could not be carried out in rapid succession, so the alloys were stored in a freezer between treatments to minimize aging. The variation in hardness with aging time, Figs. 1 to 4, was determined by microhardness testing with a 3.0-kg load. At least five readings were averaged to obtain each data point, and all measurements were taken about the center circumference of each cylinder (region of maximum deformation). Each specimen was used to obtain only one data point, i.e., specimens were not replaced in the aging bath after measurements were made. In

Jan 1, 1968

By J. B. Bassett, E. S. Rowland

INTRODUCTION THE experimental work reported herein was inspired by the publication of a paper by Grange and Stewart,1 in which it was suggested that at low chromium contents the effect of this element on the [M,] point was greater than at higher chromium contents. It was argued that, if a small increase of chromium in solution in austenite caused a sharp lowering of the [M,] point, it might lead to an explanation of occasional unsolved stress cracking of SAE 52100 during heat treatment. Commercial hardening is carried out at temperatures of incomplete solution, leaving carbides available to enrich the austenite during any inadvertent increase in temperature. Such enrichment of the austenite in chromium content would lower the [ M,] point nearer room temperature where cracking is more likely to occur. Accordingly, it was decided to investigate the effect of chromium, in quantities between o and 2 pct, on the[ M,] point of commercial steels. Fig I summarizes the data available on chromium steels. For purposes of comparison, the [M, ] temperature values were corrected by means of the Grange and Stewart formula§ to (I) Hypoeutectoid compositions: 0.50 pct carbon and 0.80 pct manganese (2) Hypereutectoid compositions: 1.00 pct carbon and 0.35 pct manganese. Only the steels having compositions reasonably close to these corrected values were included, because large adjustments inevitably introduce increased errors such as are experienced in using the formula. The straight lines of Fig I were drawn by the authors. These data obviously do not settle the question of the effect of chromium on the [M,] point, particularly at low chromium contents. While it is fairly well established that chromium causes the [M,] to be lowered when present in quantities of I pct or more, Grange and Stewart1 have suggested that in small amounts (less than I. pct) it is more effective in lowering the[ M,] point, while Klier and Troiano2 have suggested that in small amounts it is less effective in lowering the []M,] point. Payson and Savage3 concur with Klier and Troiano and further suggest that the effect is not linear at these concentrations. Rose and Fischer4 report that small amounts of chromium actually raise the-[M,] point of a 0.20 carbon steel. MATERIAL Two series of 35 lb induction heats were melted for this work, the analyses of which are given in Table I. One series was aimed at 0.50 pct carbon and 0.80 pct manganese with chromium additions in 0.25 pct increments from o to 1.5 pct with a single heat at 2.0 pct Cr. This series was considered necessary because the commercial heat treatment of SAE 52100 does not generally introduce more than about 0.60 pct carbon in solution in the austenite. The high

Jan 1, 1948

By I. W. L. Finlay, H. R. Ogden, R. Jaffee, D. J. Maykuth

Aluminum has been found to be soluble in a titanium to about 26 pct, and to raise the temperature range of transformation from a to 8. Two intermediate phoses exist in the system, a new face-centered tetragonal phase, designated as 7, which occurs between 34 and 46 pct Al, and TiAI Metallographic and X-ray diffraction data were used to determine the diagram. ALUMINUM is one of the useful alloying additions for titanium-base alloys. It is an important constituent in two commercial alloys released in 1950, one containing 4 pct A1 and 4 pct Mn, and the other containing 3 pct A1 and 5 pct Cr as the metallic alloy content. It is probable that, in the future, other titanium alloys containing aluminum will be released. In the course of alloy development work, some of the features of the constitution of titanium-rich Ti-A1 alloys have been developed. These are described in the present paper. The only available information on the Ti-A1 system concerns the aluminum-rich end of the diagram. In summarizing the early work, Hansen' indicated that there is little solubility of titanium in aluminum, and that a two-phase region exists up to the intermediate compound, TiA1a (37.2 wt pct Ti), which has a congruent melting point at 1355°C. Fink' has reported that a peritectic reaction occurs at 665°C between the melt and TiA1³ to form the terminal solid solution of titanium in aluminum. The solubility of titanium in aluminum has been established at 0.24 pct at 510°C and is estimated to be between 1 and 1.5 pct at the peritectic temperature. No information has been published on the diagram above TiAl,, other than a statement- hat aluminum raises the a to ß transformation temperature of titanium. Materials and Preparation of Alloys Iodide-type titanium and high-purity aluminum were used in this investigation. Typical analyses of these materials are given in Table 1. Alloys were prepared by arc melting on a water-cooled copper hearth, using the techniques described previously for contamination-free melting.' Weight losses during melting were very low, ranging from 0 to 0.02 g in a 10 to 15 g charge, indicating that little or no loss of aluminum occurred during melting. This permitted the use of nominal compositions for these alloys. Alloy ingots containing from 0 to 7.5 pct A1 were rolled in air at 850°C to 0.040 in. sheet. Alloys containing from 7.5 to 16 pct A1 could only be rolled about 25 pct reduction at temperatures up to and including 1200°C. Alloys containing above 16 pct A1

Jan 1, 1952

By John E. Sherborne, William M. Newton

The relation between the properties of electric logs and the fluid used in drilling a well is briefly discussed in this paper, and the fact that the resistivity of the drilling mud and its filtrate can appreciably affect such logs is shown. Apparatus was designed and a procedure established to determine the effect of various factors on the resistivity of drilling mud. Five muds commonly employed in California were tested and the following observations were made: I. The effect of raising the temperature from 80°F. to 180°F. is to decrease the resis-tiviiy of the mud or filtrate approximately 50 per cent. 2. The resistivity of the mud in most cases closely approximates that of its filtrate. 3, The change in the resistivities of muds caused by the addition of chemical is not the same function of the amount of chemical added for each mud. 4. The effect produced by increased sodium chloride content is to reduce markedly the resistivity of the mud and its filtrate. 5. Weighting materials, such as Baroid and limestone, tend to increase the resistivity of drilling mud. 6, Cement and counteracting reagents reduce mud resistivity. Introduction During recent years, the practice of "electrically logging9' a geologic formation by means of a system of electrodes lowered in a well bore has provided data of inestimable value concerning the nature of the sediments penetrated. Thus, it is generally possible, by means of electric logs, to distinguish readily the differences between shales, sandstones, cherts, limestones, and other rock forms. The distinguishing characteristics recorded in this manner have made possible long-range and closely detailed mapping and visualization of deeply buried structures1-5 to a degree not to be obtained with a reasonable expenditure of money by any other means at present in use. Besides being of value in correlation work, electric logs have been found, in some instances, to be useful in estimating the nature of fluid contained within the pores of a rock. In special cases, even the relative permeabilities at different horizons have been determined.6 That electric logs should reflect in some measure such physical properties of rocks as porosity and permeability and, in addition, give rise to data pertaining to the fluid content of rock interstices, becomes evident when the conditions giving rise to the electrical phenomena measured are known. However, it is not the purpose of this paper to review the present status of electric logging; rather, the reader is referred to the papers cited on page 220 for the principles and practice involved. Importance of Drilling FLuid in Electric Logging Because the drilling fluid must be the medium through which the electric logging device is made to traverse the formations penetrated by a borehole, and since, in general, the drilling mud completely surrounds

Jan 1, 1942

By Blake M. Loring, Robert A. Colton

MeltiXg procedures for most metals and alloys usually include some provision for the control of oxygen, since this element frequently has some undesirable effect on the properties of the metal or alloy concerned. In the melting of the various bronzes, this is especially true, since oxygen can be introduced into the melt in a number of ways, most of which are difficult to control. In making bronzes from virgin materials, oxygen is usually present in the commercial grades of copper used; electrolytic fire-refined copper ingots usually contain from 0.02 to 0.05 per cent oxygen. When ingot metal or scrap bronze is used in the charge, oxides are almost always present to some degree. Under certain melting conditions and in certain types of melting equipment the atmosphere over the metal may be highly oxidizing. This, of course, may be desirable in the melting practice used, but is certain to introduce appreciable amounts of oxygen into the melt, and that may not be entirely desirable. From the foundry viewpoint oxygen may have several harmful effects on bronzes. The formation of excessive amounts of oxides may produce drossy metal, which, in turn, means dirty castings and a potentially high rejection rate. It is claimed, too, that oxides in the metal may combine with hydrogen to form steam and thereby produce porosity in certain of the bronzes. The presence of certain refractory oxides, such as SnOz, may be undesirable from the viewpoint of making machining difficult, or as possible stress-raisers in the metal matrix. It is often said that excessive oxide present in the liquid metal makes the metal run sluggishly. Since it appears impractical to try to control the amount of oxygen introduced into the metal beyond taking the economical limit of precaution about charging dirty scrap, it would seem' that control of the oxygen content of the liquid metal offers the most promising approach to this problem. This might be done by using slags, or covers, or by the use of some element or compound added to the melt to remove oxygen preferentially. Most aspects of this problem have been considered and considerable work has been done along these lines. A reconsideration of the problem is indicated, however, by the controversial nature of the evidence at hand, especially on the possibility of using a chemical deoxidizer to control the oxygen content of bronzes. Choice of Deoxidizer The choice of the chemical agent selected as a deoxidizer would naturally depend first on the alloy in which it is to ~he used: in this particular case the alloy is Navy gun metal. In Table. I are listed a group of elements that might be considered as deoxidizers for bronze, with some of their properties that should be considered in

Jan 1, 1946

By F. Morgan, M. Muskat, R. G. Russell

Core experiments with radioactive tracers are reported in which an artificial radioactive material, radiovanadium, was used in aqueous solution in a study of the mobility of connate water. Sandstone cores saturated with active water were first oil-flooded to simulate virgin sand conditions in which the pores are filled with oil and connate water. They were then subjected to flooding with inactive water. Measurements were made of the activity of various portions of the effluent as well as the activity of the core after the flooding process was completed. In additional experiments the distribution of activity along the core was measured during the flooding process. In still other experiments direct flooding tests were made on cores fully saturated with active water. In all cases it was found that after injecting into the core a volume of inactive water equal to a pore volume, the effluent contained more than 80 per cent of the active content originally in the core. It is felt that these results imply a high degree of mobility of the connate water when subjected to flooding, although at least a partial contribution of the effect of tracer transfer within the core cannot be definitely excluded. The implications of this result with respect to water-flooding, core analysis and electric logging are discussed. A better approach to determining the connate water saturation of oil-producing rocks, by measuring the fluid content of core samples at the surface, is by the use of crude oil or oil-base muds as the coring fluid. Although water flooding is of considerable importance in the recovery of ail, comparatively little is known with certainty about the role played by the connate water during the operations. Two possibilities exist. Either the connate water is retained in the formation while the flood water sweeps past, or it is pushed along to a greater or lesser degree by the flood. Thus far no explicit recognition in terms of quantitative studies appears to have been given to the displacement of connate waters by the intruding extraneous waters, although such a possibility might be important in determining the efficiency of the oil -displacement process in water-flooding operations, especially in argillaceous rocks. On the other hand, it is a common observation that the first water produced with the oil as a result of water-flooding is definitely saline.*.' Similar questions regarding the mobility of the interstitial water arise in the quantitative description of the advance of edge-water drives. In the interpretation of the water saturations determined from core analyses, when coring with water-base muds, it is generally assumed that the drilling fluid merely adds to the connate water without displacing the

Jan 1, 1947

By Blake M. Loring, Robert A. Colton

MeltiXg procedures for most metals and alloys usually include some provision for the control of oxygen, since this element frequently has some undesirable effect on the properties of the metal or alloy concerned. In the melting of the various bronzes, this is especially true, since oxygen can be introduced into the melt in a number of ways, most of which are difficult to control. In making bronzes from virgin materials, oxygen is usually present in the commercial grades of copper used; electrolytic fire-refined copper ingots usually contain from 0.02 to 0.05 per cent oxygen. When ingot metal or scrap bronze is used in the charge, oxides are almost always present to some degree. Under certain melting conditions and in certain types of melting equipment the atmosphere over the metal may be highly oxidizing. This, of course, may be desirable in the melting practice used, but is certain to introduce appreciable amounts of oxygen into the melt, and that may not be entirely desirable. From the foundry viewpoint oxygen may have several harmful effects on bronzes. The formation of excessive amounts of oxides may produce drossy metal, which, in turn, means dirty castings and a potentially high rejection rate. It is claimed, too, that oxides in the metal may combine with hydrogen to form steam and thereby produce porosity in certain of the bronzes. The presence of certain refractory oxides, such as SnOz, may be undesirable from the viewpoint of making machining difficult, or as possible stress-raisers in the metal matrix. It is often said that excessive oxide present in the liquid metal makes the metal run sluggishly. Since it appears impractical to try to control the amount of oxygen introduced into the metal beyond taking the economical limit of precaution about charging dirty scrap, it would seem' that control of the oxygen content of the liquid metal offers the most promising approach to this problem. This might be done by using slags, or covers, or by the use of some element or compound added to the melt to remove oxygen preferentially. Most aspects of this problem have been considered and considerable work has been done along these lines. A reconsideration of the problem is indicated, however, by the controversial nature of the evidence at hand, especially on the possibility of using a chemical deoxidizer to control the oxygen content of bronzes. Choice of Deoxidizer The choice of the chemical agent selected as a deoxidizer would naturally depend first on the alloy in which it is to ~he used: in this particular case the alloy is Navy gun metal. In Table. I are listed a group of elements that might be considered as deoxidizers for bronze, with some of their properties that should be considered in

Jan 1, 1946

By M. Muskat, F. Morgan, R. G. Russell

Core experiments with radioactive tracers are reported in which an artificial radioactive material, radiovanadium, was used in aqueous solution in a study of the mobility of connate water. Sandstone cores saturated with active water were first oil-flooded to simulate virgin sand conditions in which the pores are filled with oil and connate water. They were then subjected to flooding with inactive water. Measurements were made of the activity of various portions of the effluent as well as the activity of the core after the flooding process was completed. In additional experiments the distribution of activity along the core was measured during the flooding process. In still other experiments direct flooding tests were made on cores fully saturated with active water. In all cases it was found that after injecting into the core a volume of inactive water equal to a pore volume, the effluent contained more than 80 per cent of the active content originally in the core. It is felt that these results imply a high degree of mobility of the connate water when subjected to flooding, although at least a partial contribution of the effect of tracer transfer within the core cannot be definitely excluded. The implications of this result with respect to water-flooding, core analysis and electric logging are discussed. A better approach to determining the connate water saturation of oil-producing rocks, by measuring the fluid content of core samples at the surface, is by the use of crude oil or oil-base muds as the coring fluid. Although water flooding is of considerable importance in the recovery of ail, comparatively little is known with certainty about the role played by the connate water during the operations. Two possibilities exist. Either the connate water is retained in the formation while the flood water sweeps past, or it is pushed along to a greater or lesser degree by the flood. Thus far no explicit recognition in terms of quantitative studies appears to have been given to the displacement of connate waters by the intruding extraneous waters, although such a possibility might be important in determining the efficiency of the oil -displacement process in water-flooding operations, especially in argillaceous rocks. On the other hand, it is a common observation that the first water produced with the oil as a result of water-flooding is definitely saline.*.' Similar questions regarding the mobility of the interstitial water arise in the quantitative description of the advance of edge-water drives. In the interpretation of the water saturations determined from core analyses, when coring with water-base muds, it is generally assumed that the drilling fluid merely adds to the connate water without displacing the

Jan 1, 1947