Search Documents

By Ralph Hultgren, Bernard York, David W. Mitchell

It is a well-known fact that magnesium-alloy castings are apt to be coarse grained if the melt is not superheated several hundred degrees above the melting point before casting. (The casting temperature varies according to the shape of the mold. A typical casting temperature is perhaps 1400°F.) British practice is to heat to 900°C. (1650°°F.) for 15 min., cool rapidly to casting temperature, and cast.1 In Germany superheating is carried out at 850° to 900°C. (1560° to 1650°F.) depending on the amount of scrap used. It is stated that further refinement will be obtained by prolonging the period of superheating or by increasing the superheat temperature to 950°C. (1740°F.).2 In the United States superheating is carried out at i600° to 1700°F. (871° to 927°C.), perhaps even higher in some places. It is stated that superheating effects are found as low as 1500°F. (816°C.), but several hours are required.3 These commercial treatments lead to grain sizes in sand castings that may vary from 4 to 8 grains per sq. mm.§ in heavy sections and from 60 to l00 in 3-in sections to perhaps 380 in thin sections. It is also generally known that the refining effect of superheating is lost if the melt is held for some time at lower temperatures before casting. Aside from these very qualitative statements, there is little to be found in the literature as to the effect of temperature and time of superheat on the final grain size. Because of the uncertainty of these factors, the Office of Production Research and Development of the War Production Board placed a research contract with the University of California, supervised by the War Metallurgy Committee. This research, which was done under the "Restricted" Project NRC-550, is the basis of this paper, which has been released for publication by the O.P.R.D. The material studied was an alloy prepared from carbothermic magnesium. The temperatures required for grain refinement proved to be widely different from those used in practice, as described in the statements in the first paragraph. This difference is attributed to the fact that the magnesium in the specimens was of carbothermic origin instead of the electrolytic magnesium in common use. MATERIALS AND METHODS The magnesium alloy studied was one of the most popular sand-casting alloys, with a nominal composition of 9 per cent aluminum, 2 per cent zinc, and 0.r per cent (minimum) manganese and the balance magnesium. This is designated

Jan 1, 1945

By Ralph Hultgren, Bernard York, David W. Mitchell

It is a well-known fact that magnesium-alloy castings are apt to be coarse grained if the melt is not superheated several hundred degrees above the melting point before casting. (The casting temperature varies according to the shape of the mold. A typical casting temperature is perhaps 1400°F.) British practice is to heat to 900°C. (1650°F.) for 15 min., cool rapidly to casting temperature, and cast.' In Germany superheating is carried out at 850' to 900°C. (1560° to I650°F.) depending on the amount of scrap used. It is stated that further refinement will be obtained by prolonging the period of superheating or by increasing the superheat temperature to 950°C. (I740°F.).2 In the United States superheating is carried out at 1600' to 1700°F. (871' to 927°C.), perhaps even higher in some places. It is stated that superheating effects are found as low as 1500°F. (816°C.), but several hours are required.3 These commercial treatments lead to grain sizes in sand castings that may vary from 4 to 8 grains per sq. mm.! in heavy sections and from 60 to IOO in 1/2-in. sections to perhaps 380 in thin sections. It is also generally known that the refining effect of superheating is lost if the melt is held for some time at lower temperatures before casting. Aside from these very qualitative statements, there is little to be found in the literature as to the effect of temperature and time of superheat on the final grain size. Because of the uncertainty of these factors, the Office of Production Research and Development of the War Production Board placed a research contract with the University of California, supervised by the War Metallurgy Committee. This research, which was done under the "Restricted" Project NRC-550, is the basis of this paper, which has been released for publication by the O.P.R.D. The material studied was an alloy prepared from carbothermic magnesium. The temperatures required for grain refinement proved to be widely different from those used in practice, as described in the statements in the first paragraph. This difference is attributed to the fact that the magnesium in the specimens was of carbothermic origin instead of the electrolytic magnesium in common use. Materials and Methods The magnesium alloy studied was one of the most popular sand-casting alloys, with a nominal composition of 9 Per cent aluminum, 2 per cent zinc, and 0.1 per cent (minimum) manganese and the balance magnesium. This is designated

Jan 1, 1945

By Wallace F. Lovejoy

The conservation of mineral resources as a public policy question has received a great deal of attention in the area of petroleum and practically no attention in other mineral areas, except, of course, soil and water. Some insights into mineral conservation problems and how these problems can be approached in the social decision-making process are significant. THE MEANINGS OF CONSERVATION Conservation means many things to many people .2, 11 Too often it is a label attached to a proposed program or policy to add respectability and to gain public acceptance. It is a term applied to specific resources in some contexts and to resources generally in other contexts. The oft-quoted comment of President William Howard Taft that conservation is something everybody is for, no matter what it means, succinctly illustrates the confusion over both the meaning of the concept and the policies required to implement a conservation program. This confusion goes quite deep and is more than a matter of semantics or emphasis. For example, the efficient exploitation of a mineral deposit which might be applauded as good conservation in terms of that mineral, might well result in destruction of or harm to the environment which might be viewed as bad conservation. Economics provides some tools to help solve this sort of problem, but there may be fundamental differences in value systems among groups in this society, so that ultimately society must collectively make a subjective political choice as to what is good or bad conservation policy.a An Economic Definition of Conservation The economic concepts of conservation have more relevance and are more easily applied to minerals than to many other natural resources. This does not mean that economics goes all the way in understanding mineral conservation, but at least it provides a framework for analysis which later can be altered to include noneconomic variables. Perhaps the greatest confusion in discussing mineral conservation arises in attempting to relate purely physical concepts with economic concepts. An economist is interested in maximizing or conserving values; he is not interested in maximum physical recovery or utilization. He wants to know the costs and benefits of using, or not using, resources. The economic theory of mineral-resource conservation can be labeled variously as the theory of exhaustion, the theory of resource exploitation, the theory of resource utilization, or simply as a special case of the broad theory of capital.4,28 Consideration of these labels illuminates the concerns of the econo-

Jan 1, 1976

JOHN W. BELL, *Montreal, Quebec, Canada (communication to the Secretary?). The test results in Mr. Taggart's paper will, I am sure, be recognized as a notable contribution, and of great assistance in the study of the performance of the Hardinge mill. I regret, however, being obliged to note that Mr. Taggart still retains. such confidence in the Kick-Stadler method of computing the ?relative mechanical efficiency" of crushing machines. The Rittinger-Kick graph submitted by Mr. Gates and the tests made at McGill University disclosed precisely the same fundamental defect in the Kick-Stadler theory. Consequently, I have been obliged to recalculate in terms of Rittinger surface units the results obtained in the 28 rock-crushing tests cited by Mr. Taggart, in order to find- out what the relative efficiencies really were. In order to show the large discrepancies between the Stadler and Rittinger R. M. R's, the most, efficient result disclosed by each method is represented by the number 100, and the R.. M. E.'s for the other tests have been recalculated on this basis. The results will be found in Table 1. Personally, I look forward to the time when we shall cease to talk about "relative mechanical efficiency" and merely refer to the "efficiency" of a crusher. All that is required to accomplish this is to agree on a standard method for determining the "crushing constant" of a given rock and a standard method for calculating the efficiency. The figures in the fourth column of Table 1 have been derived by assuming a constant of 2,000 for the quartzite crushed in the Yale tests. The Stadler method sometimes indicates changes in efficiency produced by, changes in operating conditions, as I pointed out in a paper describing rock-crushing tests made at McGill University. It is, however, not enough to determine that certain changes increase or decrease efficiency; surely it is equally important to determine the magnitude of these variations. By examination of Mr. Taggart's results, I have been obliged to conclude that the size of feed and amount of reduction greatly influence the Stadler R. M. E. figures, that they are positively misleading. It should be mentioned that since the majority of the tests have been made at the least efficient feed rates, and since, moreover, it is one of the evidently very important factors affecting efficiency, it is possible that different results might be obtained by a high-tonnage feed series, and that

Jan 8, 1917

By Leo F. Reinartz

The history of steelmaking in the United States is a fascinating story of determination, sudden tragedy, exploitation, and inventive genius rolled into one gigantic plot. Mr. Reinartz' flowing interpretation of the progress made in the last one hundred years is being presented in a series of four articles. THIS is the Age of Steel. We live in a mechanized era. Our everyday lives--everything we see or do-are organized and influenced by this versatile metal. Our industries, our farms, our homes, and our transportation-yes, our vocations and avocations, or luxuries and necessities-all are dependent upon smelting iron and making steel. Take away iron and steel and soon our vaunted civilization would revert to a primitive existence. These metals, often in crude forms, have been known for thousands of years. Down through the ages, until about one hundred years ago, steel was made laboriously, and at high est, in small batches. During those years, methods of manufacture did not change very much. Over long periods of time only warriors, royalty, and wealthy people could afford to use articles made of iron or steel. History has recorded that the nations which were expert in iron and steel manufacture, and had access to rich iron-ore deposits, were the leaders in war or in peaceful pursuits. At the end of the 18th century, thirteen struggling American colonies had broken not only the political shackles that bound them to Great Britain, but also many of the economic bonds. They had showed their skill, Yankee ingenuity, and energy by making iron and steel articles for their own use. After the Revolutionary War, more and more hardy American pioneers pushed westward through the Allegheny Mountain passes and down the rivers into the fertile Ohio River and Kentucky country. Demands for articles made of iron increased. The iron industry on the east coast grew and prospered. As this trend continued, iron industrialists moved their plants westward to be near the large deposits of high-grade coal in western Pennsylvania, eastern Ohio, and nothern West Virginia. They also desired to use the local iron ores and water resources of those areas. Blast furnaces and ironworks were built in the Pittsburgh, Youngstown, southern Ohio, and northern West Virginia districts. In 1810, the United States produced 53,908 gross tons of cast iron and 917 tons of steel. Iron ore discovery A white man first discovered large deposits of iron ore in the northern Michigan and Lake Superior country in 1844. One year later, the Sault

Jan 1, 1961

By Harold W. Scott

Geological Engineering is now a recognized curriculum in most of the mining schools in United States. Graduates of these schools are scattered over the face of the earth, participating in exploration and mining enterprises of diverse character. They are engaged in the mapping of new mineral deposits, in the extension of old deposits, the estimation of reserves, microscopic analysis, and in the direction of exploitation and conservation of man's natural resources. The training of men qualified to carry out these technical phases of modern industry has fallen essentially to the mining schools. For the most part they have met the demand for technically trained men in the mineral industries. Schools Offering Geological Engineering Degree The mining schools have passed through the early stages of their development and at the present offer varied curricula covering the fields of geological engineering, mining engineering, and metallurgical engineering. Usually a B.S. degree is offered in any of these three fields. However, .there has been some tendency of recent date on the part of the Engineers Council for Professional Development to question the validity of a B.S. degree in Geological Engineering. The of this paper is to examine the curricula as offered in the mining schools, to evaluate their engineering content, and to propose minimum requirements for the degree of Geological Engineering in the mining industry. The curricula of eight institutions that offer the degree of B.S. in Geological Engineering or Mining Geology have been studied (Table 1). All except one of these schools are in or near mining districts and occur west of the Mississippi River. They are all state-supported institutions that have come into existence because of the state's need for technically trained men. A graduate from .a mining school is called upon to perform many duties of a technical nature. His initial task may be to make a geological map of a mine or the surface above, but before the map is finished he may be asked to take over the responsibility of getting the ore "on top." And finally, he might find it essential to know how to mill the ore. Certainly this requires technically trained men and the mining schools are essentially the organizations to do the job. The departments of geology in these schools are training geological engineers. Field Of Geology If we were to accept the opinions of some writers, we would be forced to conclude that all geology departments offer only a "dilettante" variety of subjects.

Jan 1, 1944

By William Hume-Rothery

MR. CHAIRMAN, LADIES AND GENTLEMEN: I need not say how much I appreciate the honor of being asked to lecture to you, and how much I would thank you for your kind invitation. It is encouraging to feel that the abnormal restrictions of the war have been relaxed sufficiently to allow a free exchange of scientists between our two countries, and I hope that some of you will be persuaded to go to England, and to visit us at Oxford, so that I may repay a little of the kindness I have received from you. As this is one of the first lectures since the end of the war, I have thought it well to describe some of the advances in the theory of alloys which were made in the years between the two World Wars. From the point of view of theoretical science, these years have been of outstanding interest in the history of metallurgy. They have been years in which the development of new and more accurate experimental methods has led to the revelation of many new facts. At the same time, the theoretical developments have enabled some of these facts to be viewed as parts of a general scheme, and we may say that some of the foundations of metallurgical science have been laid. This work was naturally stopped by the Second World War, and it can therefore be reviewed as one definite stage in the development of our Science. To illustrate the new advances, I shall deal mainly with the alloys of copper and silver, since these have revealed many of the general principles. SOLID SOLUTION At the beginning of our period, the first steps in X-ray crystal analysis had been taken, and copper had been found to crystallize in the face-centered cubic structure (Fig I). The determination of this structure naturally was of immense importance in the understanding of our subject, because it meant that we were at last in a position to appreciate the underlying structure out of which the crystal of copper was built. The earlier science of metallography had shown that in many alloys of copper the addition of a second metal in not too large proportions resulted in the formation of a homogeneous alloy which was regarded as a solid solution of the one metal in copper. Fig 2, for example, shows the so-called equilibrium diagram of the copper-zinc alloys, and here you will see that there is a solid solution of zinc in copper extending to something of the order 35 to 40 at. pct zinc.

Jan 1, 1947

By B. Post, F. W. Glaser

Three borides of zirconium have been reported: ZrB,l ZrB2,2,3 and ZrB12, 4 The phase relationships, ranges of stability, and some physical properties of these compounds are described. THE zirconium borides differ considerably from one another, particularly with respect to their relative stabilities at high temperatures in the presence of carbon.4,5 ZrB2 is extremelv stable at all temperatures (to the melting point) in contact with carbon. Both ZrB and ZrB12 tend to decompose at elevated temperatures when carbon is present in excess of about 0.5 pct. ZrB forms ZrB2 and ZrC, and ZrB12 decomposes to form ZrB2 and a boron-carbide phase. In the ZrB12 preparation, boron present in excess of that needed to form ZrB2 reacts with carbon, if present, to form carbides, in preference to forming the higher boride. Similar instability of borides, other than diborides of the transition metals of the 4th and 5th groups of the periodic table, has been reported.5,6 special precautions had, therefore, to be taken to minimize carbon contamination in the preparation of ZrB and ZrB12. Reactions below 1400°C were carried out by heating powdered mixtures of zirconium hydride and boron in quartz tubes in a hydrogen atmosphere. For temperatures above 1400°C, reactions were carried out in graphite molds. Carbon contamination from the molds was minimized by employing extremely rapid heating rates to reduce carbon diffusion into the body of the specimen, and by subsequent "shaving" of sample surfaces that had been in contact with the graphite dies. A heating rate of about 2000°C per min was obtained by heating the dies (by direct conduction), using a current of 40,000 amp. Although this type of heating cycle apparently allowed little time for "homogenization," close approximations to equilibrium conditions were usually obtained as a result of the very strongly exothermic reactions between zirconium hydride and boron at elevated temperatures. Reproducibility of results in repeated runs under varying conditions was taken as a reasonable indication that equilibrium conditions had been effectively achieved. Quenching was accomplished by rapidly immersing the entire die, containing the reaction products, in water. Specimens could also be cooled at controlled rates by adjustment of the rate of flow of water through the water-cooled copper electrodes in contact with the graphite dies.

Jan 1, 1954

By S. J. Aresco, George E. Keller, J. Visman

INTRODUCTION The accurate sampling of coal, as with most minerals, is a difficult task. Coal is a very heterogeneous material made up of different types of coal and varying amounts of mineral matter. The product as mined may contain all of the layers of coal and impurities found in the seam as well as portions of the strata above and below the coal seam. The preparation plant is the device to size, crush and/or remove impurities so that the coal may be shipped as a saleable product. Sampling may be needed at many stages in the preparation process. Although this chapter is mainly concerned with sampling in connection with preparation processes, the principles will apply to all coal sampling. The main reasons for sampling in connection with coal preparation are: 1. To determine the washability characteristics of the raw coal by means of float and sink tests. These may be used for the design of a preparation plant, prediction of results to be obtained or for monitoring raw coal delivered to the plant. 2. To check the performance of various operating units in the plant, either by float and sink tests or chemical analyses. 3. To determine the analytical characteristics of the products produced, such as moisture, ash, Btu, sulfur, etc. HISTORY The earliest accepted methods of sampling coal in the United States were given in U. S. Bureau of Mines publications by J. A. Holmes,1 G. S. Pope2 and A. C. Fieldner.3 The American Society for Testing and Materials more or less adopted the methods proposed by the U.S. Bureau of Mines in their Standard D-21-1916, and it remained a standard for many years. Briefly, the standard called for a 500 pound sample for coals less than. 3/4 -in. in size and a 1,000 pound sample for all coals over ?4 -in. in size. No mention was made of increments but there was an instruction that the sample should spread over the coal to be sampled. Sample preparation was by hand crushing with the alternate shovel method for reduction to 250 pounds followed by coning and quartering below 250 pounds. Obviously, with the amount of work involved, this method of sample preparation was rarely followed. This method of preparation resulted in samples that were practically air dried because of long exposure while crushing, shoveling and quartering. In the late nineteen twenties and early nineteen thirties, studies for more practical methods were begun. Dr. E. S. Grummell4, Imperial Chemical Industries, Ltd, London, summarized the work to date at the

Jan 1, 1968

By Enid C. Plante

This paper deals with the flotation of the mineral fluorite (calcium fluoride) and of two associated gangue minerals, calcite and quartz. The aim of the investigation was to produce "acid-grade" fluorite, which must contain less than one per cent of silica. Several reagents are used successfully in practice for floating fluorite from its ores. Oleic acid is the most widely used collector, usually at temperatures above 60°C, with sodium silicate as a dispersant for quartz and quebracho or tannin to depress calcite. Sulphides (e.g., galena) are often removed first by xanthate flotation. Many investigators23 report results in which more than 80 pct of the fluorite is recovered in a concentrate assaying 96 pct or more of fluorite and less than I pct of silica. This investigation was undertaken with the intention of floating the gangue, which is the minor constituent of the ore, from the fluorite. Hence emphasis was first placed on the cationic compounds that float quartz. No satisfactory separations were obtained in this way, and other reagents were investigated to discover whether these were more effective than oleic acid in floating fluorite from quartz in the usual way. The first part of the paper describes experiments with several long-chain collectors available commercially. Most of this work has been by captive-bubble and cylinder flotation tests, with some batch tests in a flotation machine. The second part describes the use of sodium cetyl sulphate as a collector for fluorite and includes laboratory tests and extension of the work to batch tests in the flotation machine. A method for determining the adsorption of sodium cetyl sulphate on fluorite has been developed and is described. Theory of Collection by Paraffin-chain Salts It may be assumed that these compounds are adsorbed at the mineral surface in one or more of three ways outlined by Kolthoff:12 1. Exchange adsorption between lattice ions in the mineral surface and collector ions in solution. Closely related is adsorption by the collecting mechanism postulated by Taggart,17 in which there is metathesis between the collector and the mineral cation or anion. 2. Exchange .adsorption between adsorbed gegen ions (p. 67, ref. 19) and collector ions in solution. 3. Adsorption of nonelectrolytes (polar-nonpolar) without displacement of adsorbed ions. With cationic collectors, inorganic cations in the solution (e.g., hydrogen ion) compete with the collector ions and therefore act as depressants, while inorganic anions have the same effect with anionic collectors. From this follows the general conclusion that ions of the same charge as

Jan 1, 1949

By Enid C. Plante

THIS paper deals with the flotation of the mineral fluorite (calcium fluoride) and of two associated gangue minerals, calcite and quartz. The aim of the investigation was to produce "acid-grade" fluorite, which must contain less than one per cent of silica. Several reagents are used successfully in practice for floating fluorite from its ores. Oleic acid is the most widely used collector, usually at temperatures above 60°C, with sodium silicate as a dispersant for quartz and quebracho or tannin to depress calcite. Sulphides (e.g., galena) are often removed first by xanthate flotation. Many investigators23 report results in which more than 80 pct of the fluorite is recovered in a concentrate assaying 96 pct or more of fluorite and less than I pct of silica. This investigation was undertaken with the intention of floating the gangue, which is the minor constituent of the ore, from the fluorite. Hence emphasis was first placed on the cationic compounds that float quartz. No satisfactory separations were obtained in this way, and other reagents were investigated to discover whether these were more effective than oleic acid in floating fluorite from quartz in the usual way. The first part of the paper describes experiments with several long-chain collectors available commercially. Most of this work has been by captive-bubble and cylinder flotation tests, with some batch tests in a flotation machine. The second part describes the use of sodium cetyl sulphate as a collector for fluorite and includes laboratory tests and extension of the work to batch tests in the flotation machine. A method for determining the adsorption of sodium cetyl sulphate on fluorite has been developed and is described. Theory of Collection by Paraffin-chain Salts It may be assumed that these compounds are adsorbed at the mineral surface in one or more of three ways outlined by Kolthoff :12 I. Exchange adsorption between lattice ions in the mineral surface and collector ions in solution. Closely related is adsorption by the collecting mechanism postulated by Taggart,17 in which there is metathesis between the collector and the mineral cation or anion. 2. Exchange adsorption between adsorbed gegen ions (p. 67, ref. 19) and collector ions in solution. 3. Adsorption of nonelectrolytes (polarnonpolar) without displacement of adsorbed ions. With cationic collectors, inorganic cations in the solution (e.g., hydrogen ion) compete with the collector ions and therefore act as depressants, while inorganic anions have the same effect with anionic collectors. From this follows the general conclusion that ions of the same charge as

Jan 1, 1947

By L. W. Davies

A problem often encountered is the provision of materials which have impurity contents below a certain specified level. This problem is in some cases solved by making use of the segregation of the impurity with respect to the liquid and solid states of the material: an ingot of the material is subjected to directional solidification and the ends of the ingot. which are richer in solutes which respectively raise and lower the melting point of the solvent, are removed. An important extension of this process is the zone-refining process invented by pfann,' in which molten zones are passed successively along the length of an ingot and displace solutes towards the ends. Pfann's process is particularly appropriate in cases for which the segregation coefficient k does not differ greatly from unity, or when the impurity content must be kept extremely low (-=,6 atom fraction); it is widely used, particularly in the purification of materials for use in semiconductor electronic devices. It is the purpose of this paper to investigate theoretically the efficiency of the above refining processes; that is! we determine the most economic method of attaining a given yield of solvent of specified purity, taking into account the variables of the process. One variable of interest is the effective value of the segregation coefficient. which depends on the rate of movement of the liquid-solid interface and on the degree of stirring in the liquid; in addition to this, in the zone-refining process we are also interested in the choice of zone length for most efficient operation. A mathematical determination is made here of the lengths of successive molten zones which give, for an initially uniform distribution, the most efficient removal of a solute of arbitrary distribution coefficient. In order to be able to give a quantitative treatment of efficiency, we first define figures of merit applicable to a given distribution of solute. FIGURE OF MERIT Let an ingot of length L contain a distribution y(x) of solute: we confine our discussion to mono-tonic distributions, in order to avoid inconsistencies in the subsequent analysis. The first moments of the distribution about the origin and x = L are respectively L F = hy{x)dx [I] G = f(L -x)y(x)dx = YoL2-F, [21 where yoL is the total amount of solute present. We shall see that the quantities F and G are useful figures of merit for a discussion of the efficiency of zone-refining processes. In the first place, it is

Jan 1, 1960

By L. W. Davies

A problem often encountered is the provision of materials which have impurity contents below a certain specified level. This problem is in some cases solved by making use of the segregation of the impurity with respect to the liquid and solid states of the material: an ingot of the material is subjected to directional solidification and the ends of the ingot. which are richer in solutes which respectively raise and lower the melting point of the solvent, are removed. An important extension of this process is the zone-refining process invented by Pfann,' in which molten zones are passed successively along the length of an ingot and displace solutes towards the ends. Pfann's process is particularly appropriate in cases for which the segregation coefficient k does not differ greatly from unity, or when the impurity content must be kept extremely low (=10-6 atom fraction); it is widely used, particularly in the purification of materials for use in semiconductor electronic devices. It is the purpose of this paper to investigate theoretically the efficiency of the above refining processes; that is! we determine the most economic method of attaining a given yield of solvent of specified purity, taking into account the variables of the process. One variable of interest is the effective value of the segregation coefficient. which depends on the rate of movement of the liquid-solid interface and on the degree of stirring in the liquid; in addition to this, in the zone-refining process we are also interested in the choice of zone length for most efficient operation. A mathematical determination is made here of the lengths of successive molten zones which give, for an initially uniform distribution, the most efficient removal of a solute of arbitrary distribution coefficient. In order to be able to give a quantitative treatment of efficiency, we first define figures of merit applicable to a given distribution of solute. FIGURE OF MERIT Let an ingot of length L contain a distribution y(x) of solute: we confine our discussion to mono-tonic distributions, in order to avoid inconsistencies in the subsequent analysis. The first moments of the distribution about the origin and x = L are respectively L F = hy{x)dx [I] G = f(L -x)y(x)dx = YoL2-F, [21 where yoL is the total amount of solute present. We shall see that the quantities F and G are useful figures of merit for a discussion of the efficiency of zone-refining processes. In the first place, it is

Jan 1, 1960

By Robert W. Fullerton, Donald T. King

INTRODUCTION AND THEORY by Robert W. Fullerton In coal preparation plants, as in any industrial operation where raw materials are handled, nuisance problems arising from the generation of dust are inevitable. Devices for the control or collection of dust are there- fore essential components of the plant process equipment. The general term "aerosol" is applied to small particles suspended in a gaseous medium, usually air, whose velocity under the force of gravity is small enough that the particles remain suspended for a reasonable length of time. Aerosols can be classified as dust, smokes, fumes, mists or fogs. Dust includes particles originally formed by pulverization of materials by such processes as crushing, grinding, drilling, blasting and abrasion. Smoke includes particles formed from the burning of organic materials. Fumes are particles formed by processes such as condensation and sublimation, usually at high temperatures. Mists or fogs are particles formed by the condensation of water or other vapors on some nuclei. The size of aerosol particles is generally designated in units of microns, there being 1000 microns to a millimeter and 25,400 microns to an inch. Particles of about 10 microns or above are visible to the naked eye. Table 14-1 shows size characteristics of the general classifications of particles discussed above and includes typical examples of particles commonly en- countered. Table 14-1 also shows the relationship between micron size and standard screen mesh sizes. Smoke and fume are usually in the range of 0.01 to one micron, dusts are in the range of one to 400 microns, mists are in the range of 0.1 to 100 microns, and fogs are in the range of one to 100 microns. For purposes of dust control, particles greater than 10 or 20 microns in size are considered large, particles one to 10 microns are considered fine and particles below one micron are ultrafine. Sources of Dust Because coal is relatively friable, the mining and subsequent handling operations break part of the coal into dust that can be readily carried by currents of air. In a coal preparation plant mechanical handling operations such as unloading, transferring from one belt to another, screening, cleaning, and crushing in a dry state result in the generation and release of varying amounts of additional dust. The dust problem, of course, is much less serious in plants employing entirely wet processing. In addition to dust from handling operations, thermal drying of the fine coal product frequently presents another dust collection problem. Most coal driers are

Jan 1, 1968

By Michael Tenenbaum, C. C. Brown

Numerous investigatiolls have been carried out to determine the total oxygen present in the basic open-hearth bath and the results of these studies have clearly defined the factors controlling the bath oxidation during the period prior to deoxidation. On the other hand, very little is known concerning any changes in total oxygen content that may occur during deoxidation, tapping and teeming. The need for such additional data is continually becoming more apparent, since there is no strict technical basis for selecting any particular deoxidation practice. Many steels are made for the same purposes and to the same chemical analyses by widely differing practices. Apparently, each practice is satisfactory. However, it would be desirable to establish more definitely the effects and relative merits of the individual practices. Such information could be used to give a definite foundation for evaluating various types of deoxidation. In order to approach this problem, a study was made of the changes effected in the total oxygen content of several grades of steel by representative open-hearth deoxidation practices. To carry out such studies, it was necessary that a reliable testing procedure for determining the oxygen content of the steel bath and the ingot mold be established. Before entering on any extensive testing program, consideration was given to the available methods of obtaining steel samples and analyzing for oxygen. Testing Procedures It has been shown5-9 that in solidified steel oxygen may ekist in combination with iron, manganese, silicon, aluminum, titanium, chromium and carbon, depending upon the amount of these elements in the sample. In molten steel, however, there has been no direct distinction of the various oxides. Accordingly, the total active oxygen in the molten steel bath is designated by the symbol 0. During deoxidation, various oxides may be present either in solution in the molten steel or as solid or liquid inclusions. Any sample taken from the molten steel for oxygen analysis will include both the dissolved and the mechanically included oxygen. Similarly, samples of the solid steel product will also include the two forms of Oxygen' Methods of Samplirzg the Molten Steel Bath In order to obtain a true oxygen analysis from liquid steel, this element must be completely retained in the solidified sample. Several methods have been proposed whereby this stabilization can be effected. As early as 1915, Kichlinelo proposed a method for testing molten steel, in which the oxygen combined with some added aluminum. The concentration of the resultant aluminum oxide was determined by chemical analysis. This method was

Jan 1, 1945

By J. P. Matoney, E. J. Sandy, D. A. Dahlstorm

INTRODUCTION Before an understandable discussion concerning coal-dewatering processes can be initiated, it is necessary to define some terms of usage. The many different meanings and interpretations of terms preclude development of standard definitions so that the terms which are defined in this chapter should be regarded mainly as working terms intended to facilitate communication. A coal slurry ' might be defined as a watery suspension carrying particles of fine coal and other assorted material ranging upward in size from the finest clay particles. Some particles may be in the colloidal sue range and exhibit characteristics of suspended colloids. The dilution of the system generally is such that it is in a condition of independent particle subsidence. In some coal mining areas a slurry is regarded as a suspension of fine coal and other materials having a dilution that cannot be economically dewatered by filtration. A coal slime may be regarded as a slurry containing particles of such size range that 50 per cent or more (by weight) will pass a 200-mesh sieve. Slime suspensions generally are difficult to handle without special treatment in conventional sedimentation equipment. A coal sludge is defined as a slurry that has been partly dewatered by sedimentation usually to a thick or viscous consistency where further dewatering can be most readily facilitated by filtration. Culm and silt are terms characteristic of coal-preparation practice which should be defined. In anthracite terminology, culm is the generally coarse residue or waste accumulation of coal, bone and rock from preparation plants most of which are no longer functional. Culm has a wide range of sizes, some rather coarse, and except to differentiate it from silt, the term is of limited interest in this discussion. In anthracite terminology, silt is the accumulation of waste fine coal, bone and slate settled out from preparation plant water in excavated basins. Silt is generally made up of particles ranging in size from 3/32-in. round-opening screen to the very finest sues. Silt is also referred to at times as sludge, fines, slush, and mud and is the partly dewatered derivative of what has been previously defined as slurry. In the terminology of the bituminous coal producing areas, the word culm commonly corresponds to slurry or slime, depending upon the size distribution of the suspended solids. Editor's Note: Because of the numerous and varied contributions of the associate authors of this chapter, the text does not differentiate between sections authored by each individual as is the case in most chapters of this book.

Jan 1, 1968

The following persons were appointed as representatives of this Institute on, the American Committee on Engineering Standards.: George C. Stone, J. W. Richards, Arthur L. Walker. The Secretary presented a request from the Engineering Council that the representatives of the Institute be arranged in the dicier of retirement so that one would retire in 1918, two in 1919, and two in 1920. The

Jan 9, 1917

By Captain Lyle

I was very much interested in Mr. Macdonald's paper, and I can say that there is nothing in it to which I cannot heartily subscribe. In speaking of the want of knowledge that has existed, and still exists, among engineers in regard to structural materials, their strength, etc., my own experience has taught me to doubt the reliability of the ordinary testing machines.

Jan 1, 1882

Robert Annan is an Englishman who started his brilliant mining career in Arizona, yet achieved the pinnacle of success in his native land when he became chairman of The Consolidated Gold Fields of South Africa. This story of his life, prepared in collaboration with the late Henry Carlisle, continues this fascinating biographical series of important personalities in the mining industry.

Jan 12, 1964

INTRODUCTION The difference between a mineral inventory or mineral reserve and an ore reserve was discussed in the introduction to Chapter 10. The term ore reserve implied mineral in place that is capable of being mined at a profit. Potential profitability of in situ minerals is dependent upon several economic parameters in addition to grade estimates for blocks of the mineral

Jan 1, 1980