Search Documents

By Ivor Hawkes

A wide variety of borehole gages have been developed for measuring rock stress. They all operate on the principle that stress changes around a borehole result in deformation that can be measured by the gage and interpreted in terms of the stress change either by calculation or calibration. In general terms, gages that comply with the borehole deformations are referred to as “deformation meters” and those that restrain the deformations by reason of their rigidity are referred to as “stress meters.” The main advantages claimed for stress meters are: their “stress” sensitivity is much less dependent on the rock modulus than that of deformation meters, and they are clamped firmly in the borehole. The use of each of the borehole gages developed for stress determinations in rock in the main has been confined to the laboratory responsible for its development. To be generally accepted a gage must meet the following specifications : 1) Gages to be left in place to measure stress changes must be relatively cheap, and if possible recoverable, so that large numbers can be used to obtain an overall picture of the changing conditions. This, of course, is not necessarily the case for recoverable gages designed for absolute rock stress measurements where usually only one or two gages are involved. 2) For use in the adverse environmental conditions encountered underground, it is essential that gages be robust, stable, and unaffected by high humidity, corrosive water, or dust. 3) Highly qualified technicians are rarely employed specifically for rock mechanics studies in mines or on civil engineering sites and there- fore gages designed for measuring stress changes must be easy to set and

Jan 1, 1972

By F. E. Calkins

THE following presentation of the more important accumulated facts and probabilities involved in copper ore deposition is based on my experience in examination work and study of the extensive litera-ture of the subject; to make personal mention of all sources of information would require the naming of a small army of able geologists and other investigators who have contributed to, building up the science. I have tried to present the salient features of the subject in logical order and condensed form, and to point out the relative importance of processes involved. Doubt-less many geologists could suggest some changes and many additions. ORIGINAL SOURCE The original source of all copper was in the earth's interior; it has been brought to the outer part of the earth, within reach of man, in three ways: (1) By intrusions and flows of basic igneous rocks containing copper in minute quantities, presumably as silicate or sulfide. No orebodies have been formed by this method. (2) As segregations within intrusive igneous rocks, the copper minerals having solidified at the same time as the rock itself. The few deposits known to have been formed in this manner have been of little or no importance. The oft quoted Sudbury nickel-copper deposits are now known to belong to the class following. (3) By gaseous or liquid aqueous emanations from ,large deep-seated masses of intrusive molten rock. These emanations, or mineral solutions, ascended through zones of connected openings in the earth's crust and dropped their load at points far above their source. Deposits formed in this manner were the primary source of nearly all, if not all, of the world's copper production.

Jan 10, 1923

By C Gunther

Ore deposits of commercial grade are local concentrations of great rarity when considered in relation to the area of unmineral¬ized land surfaces, and they must therefore be considered as the products of exceptional and complex conditions. The data collected from a great number of individual deposits are sufficient to permit certain broad generalizations in regard to the conditions favorable to ore deposition which even numerous exceptions do not invalidate. The broadest general relation of ore deposits is with intrusive rocks, and while there are notable exceptions, the great majority of ore deposits have a visible or closely inferred connection with intrusive rock masses. Conditions that permit the dissipation of the ore-bearing vehicles do not permit the concentration of metals in deposits; the prime factor to consider in this connection is that structural conditions must be such as tend to concentrate and not to dissi¬pate the ore-bearing solutions. The disadvantage of extrusive rocks is at once apparent; any metals the magma may have contained are dissipated at the surface and are lost; with the exception of tiny vugs and cracks in quickly cooled flows, no concentrations of metals are known in extrusive rocks, and the lack of confinement and quick cooling apparently do not permit extrusives to exert mineralizing effect upon the rocks with which they come in contact. The close mineralogical similarity between extrusives and intrusives, and the great difference in mineralizing power is a proof of the ease with which magmas part with their metallic content, and of the mobility of the ore-bearing vehicles in comparison with the parent magma.

Jan 1, 1932

By James R. Dunn

The purpose of this chapter is to review the uses of sand and gravel by the construction industry. The specific intention is to give tech¬nical people the general perspective and frame¬work which they need to help in making tech¬nical and business decisions. In the sand and gravel industry such decisions are based on an understanding of sociologic, economic, and technologic factors. In order to discuss the sand and gravel industry intelligently, it is necessary to define sand and gravel. "Sand" as most often used by industry is not sand in an engineering or geo¬logic sense but should be called "natural fine aggregate." The expression "fine aggregate" is preferable to "sand" because fine aggregate in¬cludes grain sizes which, according to engineer¬ing or geologic classifications, are defined as pebble or grit size. Natural fine aggregate is distinguished from manufactured fine aggregate in that the manufactured material is crushed and screened to produce the required sizes and natural fine aggregate is only screened. Coarse aggregate is generally defined as aggregate which will not pass a No. 4 or %o-in. sieve. Coarse aggregate may be natural (gravel) or manufactured (crushed stone, crushed gravel, slag, or coarse lightweight aggregate). Gravel is usually considered sufficiently crushed to qualify as manufactured coarse aggregate when two or more sides are broken. Sand and gravel (crushed or uncrushed) is used in asphaltic and portland cement concretes, is subbase for pavements, as fill where good drainage is needed (such as around structures), and for many other uses. About 96% of all he sand and gravel produced is used in construction.

Jan 1, 1975

By Francis L. Sperry

Up to within a few years, the consumption of nickel has been more directly dependent upon the available supply than that of any of the other useful metals. The Gap mine, in Lancaster county, Pennsylvania,* has been, for the last quarter of a century, the only property in this country furnishing nickel in paying quantities. Its yearly output was about 300,000 pounds of metallic nickel, or nearly half the amount used annually in the United States. Foreign nickel from mines on the New Caledonia islands, in the South Pacific, found entrance into our markets as the production of the Gap mine fell off. The price of nickel was constantly maintained, and no special effort was made to extend its use. Over-production was cautiously guarded against, and all surplus metal was held by the banking-houses of the Rothschilds, who assumed the bonded indebtedness of the Sociètè le Nickel. The opening of the Ontario nickel-mines has, however, brought about a radical change; and nickel from the Sudbury district can be delivered in New York within four days, and in European markets within two weeks, as against two months consumed in transporting South Pacific ores. Former prices have been irretrievably smashed, and European trade-journals comment favorably on the influence which Canadian nickel has had in making lower prices, and breaking the backbone of the " nickel trust." Production and Costs. The quantity of nickel produced and the prices which it commanded may be briefly summarized as follows: The total production of the world from 1840 to 1860 was about 100 to 250 tons yearly of metallic nickel; from 1860 to

Jan 1, 1896

By Charles P. Berkey, John B. Hastings

The reconnaissance of the Goldfield mining-district, describecl in this paper, was made in May and June, 1905, and, though this time was too short for a complete report, the work accomplished may serve as a basis for more thorough future research. Dr. Berkey has examined the rocks collected by me, and I am using his classifications. As a result of further field-work, and Dr. Berkey's examination of the rocks, this paper is an elaboration and correction of my views expressed in the Gold-$elm Sun, May 12, 1905. The sketch-map, Fig. 1, illustrates the geology of the Goldfield mining-district. Goldfield is an eruptive complex, consisting of alaskite (hinary granite), hornblende-andesite, hornblende-dacite, rhyolite, pyroxene-andesite, pyroxene-dacite (sometimes containing a small quantity of olivine), quartz-felsite, olivine-pyroxene-ande-site, and basalt. Considering this list to be arranged in the order of eruption, the age-sequence of the rocks conforms to Richthofen's law, formulated in 1868. From his observations in Europe and America, propylite, andesite, trachyte, rhyolite and basalt, occurring together, succeed one another. In a general way, the medium and the more acidic rocks precede the most basic—a result supposed by some to hare arisen from their position beneath the. surface, and due to a rude stratification by gravity in the original cooling magma during the older history of the earth, or to the same differentiation occurring during a quiescent (molten ?) period preceding eruption, being aided by the ease with which acidic rocks, mixed with water vapors, become fusible. In effect, the more basic and less re-

Jan 1, 1907

By Prof. B. Hopkinson

Introduction.-A short time ago Professor Stoughton asked the writer if he would present a paper for the February meeting of our Institute. In reply to this suggestion, some notes have been prepared relating to the subject mentioned in the title. It is to be hoped they may be of interest to our members. The research now described is the joint work of Prof. B. Hopkinson, F. R. S., and the writer. Those interested in the subject will find further data in a paper entitled The Magnetic and Mechanical Properties of Manganese Steel, which will probably be read at this year's May Meeting of the Iron and Steel Institute in London. This paper was submitted to the Institute in October last, and advance copies will shortly be available. The present paper has been drawn up by the writer on this side the water, and he has not had time to communicate with Professor Hopkinson with regard to the statements or opinions expressed herein. While the writer believes that Professor Hopkinson would in the main agree with the statements herein set forth, it should be understood that apart from the actual work described he is not otherwise responsible. The experiments described have been carried out on the material known as manganese steel, which one of the writers of these notes discovered in 1883. A paper by him describing this material was read before this Institute in 1893, entitled Iron Alloys, with Special Reference to Manganese Steel. It is not necessary to describe manganese steel nowa-days; its qualities are so well known, and its use throughout the world is on a very extensive scale.

Jan 3, 1914

The early Spanish adventurers found but little gold or silver on the American mainland, and the aborigines in the country that is now the United States were not as submissive as those of the West Indies, so the conquistadores obtained no foothold north of the Caribbean sea. Their later exploration north- ward had Mexico as a base-and wild yarns as a basis. The friar Marcos, a member of Estevanico's unfortunate expedition, brought the story of the Seven Cities of Cibola to Mexico City in 1539. Except as Indian hovels,* they existed only in a disordered imagination, but when Váquez de Coronado's expedition pricked the glittering bubble, there appeared an enticing mirage in the northern desert: the glorious land of Quivira, where even-the common pitchers and bowls were made of solid gold. Coronado proceeded northward and found only enormous herds of buffalo on the plains of Texas. It was a melancholy land. No gold or silver was to be seen among the poor Indians. Coronado reached the country of the Wichitas, in Kansas, before he abandoned his quest and turned home, which he reached, with only a third of his party, hungry and tattered, in 1542. So long as greed stimulates the imagination there will be no lack of tales such as those that repeatedly led the Spaniards to the rainbow's end. In 1860 an expedition was organized in San Francisco by Dr. Darwin French to explore the desert country near Owens lake on the news that the Indians in those parts shot golden bu1lets.t The fact that the savages were known to possess few guns did not discredit the tale, which

Jan 1, 1932

By Henry G. Granger

Repeated failures in attempts to work gold-bearing gravels by means of suction-dredges have created the impression that this method is impracticable. The suction-dredges have failed from three special causes: excessive wear and frequent breakage of pump-shell, runners and liners; inability to dredge compact gravel which would not readily move towards the intake; and, most important of all, closing of the suction-pipe by stones too large to enter it. In my opinion, all three causes of trouble may be remedied: the first, by making stronger the parts most liable to wear and breakage; the second, by means for loosening the gravel at the intake; and the third, by sufficiently increasing the diameter of the suction-pipe. In suction gold-dredges, this diameter has not usually exceeded 10 or 12 in.; whereas there are few profitable gold-fields which call be considered dredge-able, in which stones more than 12 in. in diameter are not frequently encountered. II. An Effective Suction-Dredge. In harbor-operations, much larger stones are handled by suction-dredges. The large dredge of the Henry Steers Contracting Co. worked for nearly four years at League Island, Philadelphia, where it sucked up, passed through the pump, and forced through 3,700 ft. of discharge-pipe, gravel containing boulders up to 200 lb. in weight. This was done with no bad breaks and few shut-downs. The cutter and liners were the only parts liable to damage, and these were easily replaced with brief interruption of work. The chrome-steel liners are said to have lasted from six to nine months. I am informed that this dredge worked continously for nine

Jan 1, 1910

By Walter Harvey Weed

In a previous paper upon the enrichment of mineral veins by later metallic sulphides,? the writer has shown that certain masses of rich ores, such as are found in many mines, either near the water-line or as bonanzas in depth, are of secondary origin, and are due to a leaching of lean ore and the concentration of the material by reaction between the solution and the unaltered ore below. The geological and mineralogical evidence is believed to form an adequate basis for a chemical and physical explanation of the phenomenon. In the present paper the writer will give a brief synopsis of this theory, and will apply it more particularly to deposits of the precious metals, laying special emphasis upon the dependence of such enrichments upon the presence of iron sulphide (as pyrite, etc.) in the primary ore, and upon structural features which control the circulation of the enriching solutions below the water-level. It is believed that many, though not all, of the bonanzas arid pay-shoots of rich sulphide ores, especially those carrying gold and silver, which are encountered in ore-deposits, are of such secondary origin. Apparently it is essential that the occurrence and structural relations of such ore-masses should be understood, as the success of the mine is often dependent upon the finding and extraction of these ores. A legitimate deduction, too, is that such ore-deposits decrease in value With depth. As my own studies have been mainly in Montana, my illustrations must be drawn from the ore-deposits of this and adjacent States, with such as I have noted in hurried visits else-

Jan 1, 1901

By B. S. Butler, H. D. McCaskey

The New London copper mine, about 8 1/2 miles east of Frederick, Md., was visited by the writers for a few hours in the spring of 1909 and the following brief notes on ore specimens collected are presented as a contribution to studies in chalcocite ores. For certain data on the structural and areal geology of this portion of Maryland the writers are under obligation to the unpublished notes and maps of Arthur Keith. The detailed study of the ores is the work of B. S. Butler. The deposit here discussed has many similarities to those of the Virginia district of Virginia and North Carolina, which have been described by Gratonl and Laney,2 except that in the deposits of the New London mine chalcocite is by far the most important ore mineral, while in the Virginia deposits bornite is commonly the most important sulphide. In the New London occurrence calcite is the most important gangue mineral. Field relations The -town of Frederick lies in the center of a narrow belt of limestone ranging in age from Ordovician on the east to Cambrian on the west. This belt is about + mile wide at Noland's Ferry, on the Potomac, and broadens to a width of 3 miles at Frederick. The general direction is east of north. The eastern boundary is, in places, a fault plane along which a series of metamorphic rocks of presumptive pre-Cambrian age have been thrust up. These ancient rocks, for several miles east and west of New London, are phyllites in the main, but closely inter-folded near the New London mine are long, narrow lenses of epidote

Jan 1, 1915

By F. Peter

Technical progress takes place in two directions: the improvement of methods, affecting the quality of the product; and increase in the economy of operations, affecting its cost. In the iron-industry, practice is pretty well settled, and revolutionary changes of method are, for the present, not to be expected. Hence, in this industry, the principal endeavor is to reduce costs by the use of labor-saving inventions, such as the machines brought into use during the last decade. But it is not alone necessary to reduce the labor-cost; complete economy requires also a saving in raw material. Under this head we may rank the coal employed as metallurgical fuel; and it follows that progress includes the economic use of fuel, so managed as not to injure quality of product. In the present paper it will be shown how, by suitable utilization of the heat from the furnace, a large portion of it may be made available for other purposes. Such utilization of waste-gases is important in all industries which employ furnaces (especially heating-and smelting-furnaces); and in the first rank of these stand the iron-, glass-, and porcelain-manufactures. The following pages are devoted chiefly to the waste-gases of smelting-works, and especially to those reverberatory-furnace gases which are not combustible.' The object of metallurgical furnaces is either to fuse the material charged or to bring it to a high temperature required for further mechanical manipulation. Leaving out of consideration for the present the reverberatory fusion-furnaces, we have to do with the heating-furnaces employed in connection with rolls, hammers, or hydraulic presses. The temperature to which the material must be

Jan 1, 1914

By H. H. Stout

IN the early fall of 1925, the writer was conducting, in the Ledoux and Co. labora-tory, New York, experiments directed to-ward ascertaining the effect on its impurity content when cathode copper was subjected to a current of various gases at an elevated temperature below the melting point, The apparatus consisted of a vertical 1-in. dia. silica tube about 12 in. long, heated on the outside, The cathodes were broken to pass a8-in. mesh, and a current of various differ-ent gases was passed up through a 4-in, long column of these loose cathode particles in the vertical tube furnace. Temperature was maintained to i500° to 1600°F. and the gas treatments lasted from 3 to 6 hr, The writer observed that whenever reducing gas (H2 or CO) was used, these cathode par-ticles stuck together at points of contact with each other. The cohesion was so marked and tenacious that an examination was made of the fractured surfaces, when cathode particles were broken from the cluster. Crystal growth was always found to have taken place across the surfaces where separate particles were in contact, but only after all oxides, sulphates, etc, had been completely removed. The idea of a possible new process was then conceived and was disclosed to A. M. Smoot (V. P. Ledoux and Co.) with intent to obtain his views. The first conception as given Smoot was "to gas-clean broken cathodes, put them in an extrusion press, solidify and extrude them at around 1500°F," Smoot's reaction, after a few moments considera-tion, was, "It looks perfectly all right to me."

Jan 1, 1940

By Edgar C. Bain

In studying the structural characteristics of martensite it is desirable that a clear conception of the material from which martensite is produced should first be obtained. Any theory of its formation and structure incompatible with the facts of its parent substance, austenite, can be eliminated with little consideration. Austenite is the name applied to solid solutions of carbon and other elements in gamma iron. At temperatures above about 900" C. (1650" F.), pure iron exists in a system of crystallinity1 entirely different from the crystal structure below that temperature. This high-temperature allotrope of iron is of an atomic structure associated with great ductility, having very manifold symmetry and an abundance of easy slip planes. The exceptionally ductile and malleable metals (gold, silver, platinum, copper, aluminum, and nickel) have this same atomic arrangement— the face-centered cubic. The low-temperature allotrope of iron, alpha iron, the solid solutions of which are known as ferrite, has a body-centered cubic arrangement of atoms. Like it, in crystal structure, are the less ductile and malleable metals, molybdenum, tungsten, titanium and chromium. Fig. 1 shows the two atomic arrangements known in iron; the diagrams are drawn to scale. Either of these modifications of iron may dissolve other elements in the solid state; by so doing, the temperature of the transformation is changed. In general 2-7, it appears that a solid solvent metal dissolves a metal solute by substituting foreign atoms in its own space lattice. Thus, iron may dissolve nickel in either of its crystalline forms by permitting an atom of nickel here and there to occupy the normal position

Jan 1, 1924

By Edgar C. Bain

In studying the structural characteristics of martensite it is desirable that a clear conception of the material from which martensite is produced should first be obtained. Any theory of its formation and structure incompatible with the facts of its parent substance, austenite, can be eliminated with little consideration. Austenite is the name applied to solid solutions of carbon and other elements in gamma iron. At temperatures above about 900" C. (1650" F.), pure iron exists in a system of crystallinity1 entirely different from the crystal structure below that temperature. This high-temperature allotrope of iron is of an atomic structure associated with great ductility, having very manifold symmetry and an abundance of easy slip planes. The exceptionally ductile and malleable metals (gold, silver, platinum, copper, aluminum, and nickel) have this same atomic arrangement— the face-centered cubic. The low-temperature allotrope of iron, alpha iron, the solid solutions of which are known as ferrite, has a body-centered cubic arrangement of atoms. Like it, in crystal structure, are the less ductile and malleable metals, molybdenum, tungsten, titanium and chromium. Fig. 1 shows the two atomic arrangements known in iron; the diagrams are drawn to scale. Either of these modifications of iron may dissolve other elements in the solid state; by so doing, the temperature of the transformation is changed. In general 2-7, it appears that a solid solvent metal dissolves a metal solute by substituting foreign atoms in its own space lattice. Thus, iron may dissolve nickel in either of its crystalline forms by permitting an atom of nickel here and there to occupy the normal position

Jan 1, 1924

By John Birkinbine

In the belief that a resume of what will be exhibited during this meeting, and a brief record of progress in the seven years which have elapsed since the Institute's first visit to Lake Superior would be interesting, the following statistical data have been prepared or copied from the most reliable sources, and considerations are also presented concerning the development or utilization of some of the resources of the Lake Superior Region. When the Institute, on the return trip from enjoying the charming panoramas of Thunder Cape or Isle Royale, and inspecting the unique development of Silver Islet, passed, in August, 1880, through the St. Mary's Falls ship canal, en route to Escanaba, the boat was lowered from the level of Lake Superior to that of Michigan and Huron lakes (18 feet), through two locks each 70 feet wide and 350 feet long, which had been in use since 1855. But as these locks accommodated vessels which drew 12 feet of water or less, a new lock 80 feet wide, 515 feet long and admitting vessels of 16 feet draught was approaching completion and was opened in September, 1881. The time required to pass the locks was utilized by the members in examining the work upon this new lock and in viewing the Sault Ste. Marie, which in discharging from Lake Superior all average volume of 90,783 cubic feet of water per second, forms a rapid, falling 18 feet in one mile. But the lake traffic through the St. Mary's ship-canal has developed so rapidly that another and larger lock is now required, and work has been commenced by the

Jan 1, 1888

By Arne F. Westgren

X-ray analysis and single-crystal study have been utilized in recent years as a new means of following constitutional changes in alloys. If such transformations can be suppressed by rapid cooling, they can be followed at room temperature in a particularly convenient manner. In the following we shall consider changes in solubility and polymorphic transformations with particular reference to phenomena of the age-hardening type. Finally a thermodynamic viewpoint is developed for examining such transformations. Changes in Solubility 1. Determinations of solubility limits in the solid state which show decreasing solubility with falling temperature are made as follows: A series of alloys extending into the heterogeneous region is prepared and quenched fromas high a temperature as possible, whereupon their lattice parameters are determined. Then one or more alloys are quenched from temperatures at which they are heterogeneous and their lattice parameters likwwise determined. For the purpose of determining the parameter the apparatus shown in Fig. 1 has been very useful for it produces sharp films in a short time which can be accurately read. High-order reflections (interferences) from the object are recorded on a film which is placed exactly perpendicular to the X-ray beam. The specimen usually has the shape of a small round bar.l Fig. 2 shows a selection of such exposures of silver-rich Cu-Ag alloys, and Fig. 3 gives the measurements made from these films. Fig. 4 gives the solubility curve which results.2 This curve is shifted to lower concentrations than the curve that is obtained from metallographic or physical methods. The X-ray method unquestionably gives more reliable data

Jan 1, 1931

By Oscar M. Wicken

Industrial minerals - being the basic materials for much of the industrial activity in the world -suffer or gain in the market place with changes in that activity. The period 1970 and early 1971 has been one of little growth in many of the mineral-consuming industries, particularly those associated with building and construction. Consequently, the production of many commodities revealed little or no increase above 1969 levels. The pick-up of construction activity in the last half of 1971, however, is expected to be at an intensity which will result in an over-all good year; for example, cement shipments may, establish a record. Some industrial minerals products that bucked downward trends were those allied with the agricultural industry. Phosphate rock shipments increased, particularly from Florida which contributes over 400/c of the phosphate rock in the western world. Potash had higher sales and production for the third straight year, which means that inventories are being eased. The catch-all term of ecology is an oft-mentioned theme among industrial minerals suppliers. Specifically, the need for control of dust emissions is adding a heavy capital investment burden to many of the producers; such a burden, in fact, that plants have had to cease operations because the cost of dust collection equipment could not be born. As an order-of-magnitude estimate, dust collection equipment for cement plants can run $2-3 million for a single plant; some estimates are that the total cost of dust collection equipment in a new plant can be approximately 20% of total investment. All minerals processers have dust control expense of greater or lesser proportion.

Jan 1, 1972

By AIME AIME

THIS year the Chairman of the Institute's Iron and Steel Division is THIS William Anderson Haven, better known to the membership generally as Bill Haven. The Division Chairman is an individual endowed with a broad perspective of the ferrous metal industry he result of his earlier experiences as a successful operating man in the working and management of blast furnaces and his later experiences as an engineering-consulting executive concerned with the design and erection of and steel works throughout the world. William A. Haven was born to iron steel in the Pittsburgh district on ;. 1, 1888, and in due time--or in 1909 graduated from Penn State with a Bachelor degree in industrial chemistry.

Jan 1, 1944

By E. A. Cappelen Smith

FOR distinguished service in the art of hydrometallurgy, the Mining and Metallurgical Society of America presented its gold medal to E. A. Cappelen Smith, at a dinner held in the Hotel Commodore, New York, on Nov.' 10, 1920. Prof. Waldemar Lindgren, president of the society, in giving the medal, said: "By the advancement of the science of hydrometallurgy, by the construction of plants on a scale audacious in their conception, by the successful overcoming of all sorts of difficulties, you have placed your name among those who occupy the very front rank among the hydrometallurgists. In recognition of this distinguished contribution to the science of metallurgy, the Mining and Metallurgical Society of America now awards you its gold medal."

Jan 1, 1920