Search Documents

By J. E. Tobey, David R. Mitchell, J. H. Kerrick

DETAILED knowledge of purchase specifications established by coal consumers is essential to the successful design and operation of a coal-preparation plant. ANTHRACITE Specifications should be considered by both the consumer and the producer as guide posts outlining a certain path for both to follow. Plants differ, therefore specifications must differ to meet the varied requirements. Specifications are not of themselves a "cure all" or an assurance of complete satisfaction in fuel utilization. Specifications should not be regarded as a license to engage in an orgy of buying any and all coals that may happen to fall within their limits. This would lead to the indiscriminate mixing of coals which may vary in their burning characteristics. Different coals of equal grade tend to be individualistic in their burning characteristics. Rather, specifications should be used to help simplify coal selection, to reduce the actual number of coals used over a given period; in other words, to have a stabilizing influence on coal or customer turnover. In the final analysis, the use of too many coals per year in a plant is costly to both the consumer and the producer. Too many sources usually result in higher operating and maintenance costs for the consumer and higher sales costs for the producer. Finally, the statement included in the report accompanying the com¬prehensive Coal Selection Charts prepared by the Coal Committee of the National Association of Purchasing Agents, and released in 1938, is significant. This Committee worked diligently for a period of 15 years seeking to find a scientific and reliable method for selecting coals. The two following paragraphs are quoted from its report: More important is the fact that no ready-made classification or set of specifications can possibly replace the judgment and resourcefulness of an experienced combustion engineer or fuel technologist, nor the usual need for full scale plant tests under the exact conditions of use before a final decision is made ...

Jan 1, 1943

By Portland P. Fox, Berlin C. Moneymaker

THE development, within recent years, of core drills capable of drilling holes up to 72 in., or even more, in diameter, has made possible an entirely new and valuable method of geologic exploration. Although little used until recently as an exploratory tool except in the United States, by the Tennessee Valley Authority and the Corps of Engineers of the U. S. Army, for the exploration of damsites, the large-diameter core drill may be used to good advantage in other types of geologic exploration. Its principal utility is that of supplementing, rather than replacing, other means of exploration. Although core is frequently recovered intact, the greatest advantage of large-diameter drilling is that the holes produced are large enough to be entered by the geologist and engineer, and thus afford an excellent means of examining undisturbed rock. The walls of the holes are smoothly cut, and in some rocks nearly or quite polished, so that the most minute details of structure and stratigraphy are clearly disclosed. Such features as faults, joints, bedding planes, weathered "seams," and beds or layers of soft materials, which are not always amenable to disclosure by cores recovered from small-diameter holes, are conspicuously displayed in the walls of large holes. Frequent reference to the drilling of large-diameter holes is made in engineering literature, but comparatively little emphasis has been placed on their value in geologic investigation. It is, therefore, intended that the present paper acquaint the geologist, as well as the engineer, with the large-diameter core drill and the technique involved in its use, and also with its advantages, disadvantages and limitations as an implement of geologic exploration. THE EQUIPMENT The equipment generally employed in the drilling of large-diameter holes consists of a trunnion-type drill head mounted on a sliding base, which allows it to slide clear of the hole and thus permit the introduction

Jan 1, 1938

This report presents the comments of members of the Institute's Sub-committee on Physics of Mine Ventilation on the proposals of a special committee of the Institute of Mining Engineers (London). This report is as follows: THEORY OF MINE VENTILATION Abstract of a report submitted June 16, 1925, to the Council of The Institution of Mining Engineers by a Special Committee Laws of Flow of Aib The law of flow of air in mine galleries is, at present, expressed by two formulas differing slightly in shape but both derived from the original hydraulic formulas of Chezy and others. These formulas are: The Atlcinson Formula.—Pa = KsV2, which in transformation becomes a3 where P = pressure producing flow; K = coefficient of friction; s = surface of the mine galleries; V = velocity of flow; Q = rate of flow; a = area of mine galleries. This formula is especially applicable to mine galleries, but is unwieldy in application, as in many problems we are dealing with changes produced in the same set of airways when K, s, and a are assumed not to change, and the only variables are P and Q. Great uncertainty prevails as to the exact values to be assigned to the coefficient K in different types of airway, as different workers have given widely differing values. This formula assumes: (I) That resistance to flow is independent of the pressure within the gallery. (2) That changes in volume within the limits of pressure ordinarily met with may be neglected. (3) That changes in density and viscosity and mode of flow of the air may be neglected. (4) That the coefficient K is a constant. (5) That P is proportional to the square of the velocity. We cannot find any reliable experimental work leading us to conclude how far these assumptions are justifiable in mining practice. Equivalent Orifice Formula.—The fundamental form of this formula is Q = ~nA.\/2~11

Jan 1, 1927

By O. S. True, C. H. Herty

It is well known that manganese will desulfurize molten iron through the formation of manganese sulfide, which, being only slightly soluble in the metal, rises to and enters the slag where it remains as such (mixer slag) or is converted partly or wholly to calcium sulfide (basic open-hearth slag). The reaction by which manganese sulfide is formed is Mn + FeS = MnS + Fe. This reaction is generally considered to be reversible, although McCancel states that such is not the case. The experimental work was carried out to confirm the results of Roh12 as to the reversibility of the reaction. Six trials are herein considered. In each 200 gm. of electrolytic iron free from manganese and sulfur were melted in a pure zirconia crucible in a carbon resistance electric furnace. To the melted iron in runs 2, 3 and 4 metallic manganese and manganese sulfide were added to give 1, 2 and 4 per cent. manganese respectively, with 0.50 per cent, of sulfur in each. In runs 5, 6 and 7, metallic manganese and iron sulfide to give the same proportions of. manganese and sulphur as in runs 2, 3 and 4, were added. The melts were held molten in the furnace for an hour and then cast into small ingots. The results of these melts are as follows: Ingredients of Charge Analysis or InRot ManOaneBe, SulfUR, ManOaneBe. SULFUR, Run Material Charged PeR Cent. PeR Cent. Per Cent. PeR Cent. 2 MnS + Mn............... 1.0 0.452 0.636 0.367 3 MnS + Mn............... 2.0 0.50 1.57 0.310 4 MnS + Mn............... 4.0 0.50 2.81 0.230 5 FeS + Mn................ 1.0 0.50 0.647 0.397 6 FeS + Mn................ 2.0 0.50 1.45 0.374 7 FeS + Mn................ 4.0 0.50 2.73 0.195

Jan 1, 1925

By M. L. Fuller

DURING the last several years many papers have appeared dealing with the structure of highly polished metal surfaces The awakening of interest in this subject is due to the applicability of the electron diffraction technique to the study of surfaces The original theory of Beilby1 considered the surface of polished metals as of the nature of a super-cooled liquid or a vitreous, amorphous solid The electron diffraction effects from polished metals have been interpreted by many to be a direct experimental proof of the correctness of the Beilby theory This interpretation has been strongly opposed by others, so that at the present time the subject is in an uncertain and controversial state In the present paper new, and hitherto unpublished, electron diffraction effects from polished zinc are described These observations indicate that the polished surface of zinc is crystalline PUBLISHED WORK Many papers2-10 have interpreted the electron diffraction evidence as proof of the Beilby amorphous theory All investigators agree that highly polished metals give rise to two diffuse diffraction haloes, similar to those obtained by the diffraction of X-rays in liquids and vitreous solids It is this similarity that leads to the amorphous-layer interpretation of polished metals Strangely, the interatomic distances calculated from these haloes are very similar for the various metals investigated, in spite of a rather wide range of such distances in the crystalline and liquid states The calculated atomic sizes are, furthermore, smaller than are experienced in the normal states of the metals In spite of these anomalies, the amorphous-layer interpretation has been adhered to by many One investigator, S Dobmski,11 differs from the others in his experimental results By polishing under benzene in order to avoid the possibility of oxidation, Dobinski obtains diffuse haloes of [radire] different from those previously obtained He thus obtains a more rational quantitative correlation of-the diffuse haloes with the amorphous-layer theory

Jan 1, 1938

By C. F. Mabery

So far as the elementary composition of petroleum is known, it may be briefly stated. Petroleum consists principally of a few series of hydrocarbons, with admixtures of sulfur, nitrogen, and oxygen derivatives in comparatively minute proportions, which may be regarded as impurities to be removed in the preparation of commercial products. But as each series is represented by many homologs, in the aggregate, crude petroleum is an extremely complex mixture of hydrocarbons and their derivatives. In part, these hydrocarbons individually conform in structure to the system of synthetic hydrocarbons whose structure is well defined and represented by the typical series CnH2n, + 2, C.H2n, the series CnH2n,-2, CnH2,-a, the members of which have not been sufficiently studied to establish their structure, and the series CnHz,e composed of the aromatic group, benzene and its homologs. Hydrocarbons of greater density contained in the portions of petroleum that cannot be distilled without decomposition doubtless have less hydrogen than is represented by these formulas. Since to every hydrocarbon there is a definite temperature, even in vacuum, at which its constituent carbon and hydrogen atoms fall apart, and since for the heavier bodies this temperature is not much above 360" C. in vacuum, it is evident that some other method than distillation must be devised for their separation if anything further is to be learned concerning their individual constitution. Classification of Petroleums There is such a wide variation in the composition of petroleum from Merent fields, it would seem possible to make a classification on this basis were it not that no single variety is entirely free from hydrocarbons contained in others. Such a classification has been suggested of the exceptionally pure Pennsylvania petroleum, the sulfur oil from Trenton limestone and other sources, the California oil with its large amount of nitrogen (quinoline) derivatives, and the Russian oil, composed chiefly of the naphthene hydrocarbons.' A commercial distinction is made

Jan 1, 1921

By C. E. Meissner

The need for a practical method of deciding upon new alloy steel analyses to widen its markets was the problem facing the Chrome Steel Works at the beginning of 1927. In addition to determining the physical properties of the alloys under consideration, it was necessary to test their value in service. Small melts of steel in a crucible, from which test specimens could be made, were insufficient to determine more than physical properties, therefore actual castings and ingots had to be made before the products could be placed in service. Furthermore, to save further experimental work, it was desirable that these heats should be made on a "pilot" basis; that is, actually duplicating regular open-hearth furnace practice. Therefore a one-ton (2000-lb.) acid open-hearth furnace was built. Furnace Design There are no special features in the design of this furnace. Standard acid open-hearth practice is followed, with the reproportioning of the dimensions necessitated by its small size; notably, a considerably increased length in proportion to width in order to get proper flame propagation. After the first heat was made it was found that the check-ers were insufficient. The checker chambers were increased in size and the checker openings were made much smaller. The furnace was started late in March, 1927, and made 65 heats. Experimental work was then stopped unti1, the data accumulated could be worked up and summarized. The run was resumed in November and the furnace is still operating, having made at this writing 60 additional heats. For the last series of runs, there was some rebuilding of both the furnace itself and the checkers. Slag pockets were added. Fig. 1 shows details of construction; Fig. 2, the general appearance. All designing was done by the operating and engineering staff. Construction materials were those available around the plant. The reversing valve is a standard butterfly type taken from an old furnace. The slag pockets and checkers are cleaned by digging down to arched openings which have been bricked up.

By Portland P. Fox, Berlen C. Moneymaker

The development, within recent years, of core drills capable of drilling holes up to 72 in., or even more, in diameter, has made possible an entirely new and valuable method of geologic exploration. Although little used until recently as an exploratory tool except in the United States, by the Tennessee Valley Authority and the Corps of Engineers of the U. S. Army, for the exploration of damsites, the large-diameter core drill may be used to good advantage in other types of geologic exploration. Its principal utility is that of supplementing, rather than replacing, other means of exploration. Although core is frequently recovered intact, the greatest advantage of large-diameter drilling is that the holes produced are large enough to be entered by the geologist and engineer, and thus afford an excellent means of examining undisturbed rock. The walls of the holes are smoothly cut, and in some rocks nearly or quite polished, so that the most minute details of structure and stratigraphy are clearly disclosed. Such features as faults, joints, bedding planes, weathered "seams," and beds or layers of soft materials, which are not always amenable to disclosure by cores recovered from small-diameter holes, are conspicuously displayed in the walls of large holes. Frequent reference to the drilling of large-diameter holes is made in engineering literature, but comparatively little emphasis has been placed on their value in geologic investigation. It is, therefore, intended that the present paper acquaint the geologist, as well as the engineer, with the large-diameter core drill and the technique involved in its use, and also with its advantages, disadvantages and limitations as an implement of geologic exploration. The Equipment The equipment generally employed in the drilling of large-diameter holes consists of a trunnion-type drill head mounted on a sliding base, which allows it to slide clear of the hole and thus permit the introduction

Jan 1, 1941

By C. W. Davis, R. S. Dean

The purification of iron ores by means of hand magnets dates back more than 100 years. The first record in the United States Patent Office of a machine for the magnetic separation of ores shows that on Feb. 20, 1849, U.S. Patent 6121 was issued to Ransom Cook for improvement in electromagnetic ore separators. The patent covered the use of a revolving cylinder, or drum, with poles of electromagnets in its periphery for the purpose of separating magnetic oxide of iron from substances with which it might be associated, by causing the electrornagnets when revolving as component parts of the cylinder to be successively charged to take up the ore and discharged to part with it. Since this patent was issued the science and technique of magnetism have advanced more than most other fields of endeavor. The development of electrical machinery has required and obtained better and better magnetic materials, and the science of applied magnetism is as completely and satisfactorily developed as any branch of physics. Nevertheless, the patent of Ransom Cook, issued in 1849, comes close to covering everything that is now being applied in magnetic separation. The cynic may conclude that this proves the uselessness of modern science and may point in confirmation to flotation, which has grown in a few years, practically without benefit of science, to be the most versatile and useful of concentration methods. On more careful study, however, it appears that an accurate determination of the magnetic properties of minerals and their amenability to control by mechanical and heat treatments has not heretofore been made. The first essential, therefore, in the design of improved magnetic separators has been missing. In spite of this hiatus in scientific data inventors have been busy, and patents are on file covering mineral separations by means of nearly all known magneto-mechanical effects. Because of a lack of knowledge of mineral properties, most of these inventions never worked well enough to find commercial use. The Metallurgical Division

Jan 1, 1935

By W. H. Newhouse

DURING the past few years the writer has been impressed by the close relation of many epigenetic orebodies with anticlinal structures. In the literature on ore deposits there is occasional mention that an oreshoot or district is on an anticline, but in most of the descriptions no weight or significance is attached to the relation, and usually the fact is concealed in a mass of structural detail. A few writers have stressed the relationship in a few districts or on a certain type of deposit. Church, Spurr, Butler, Stahl and Schuette have called attention to certain features, but the general extent of such a correlation has not been made known in any publication that the author has seen. A recent article1 on the localization of ore deposits, by well-known geologists, does not consider this common association. The author has seen in the field a number of the structural features described, and in addition has made a fairly complete review of the literature. This paper presents enough of the examples found to show the frequency of the relation to anticlines, and since only a few deposits on synclines are known, all of these of any importance of which the writer knows are mentioned. With certain qualifications which are discussed later, epigenetic ore deposits of replacement or vein type are mostly found where local upwarps of the earth's crust have taken place. Where formations antedating the ore deposits are present in the proper attitude to demonstrate vertical warping (i. e., more or less horizontal beds) the structural feature on which a mineral district, or mineralized area is located is almost always anticlinal, or domelike in nature. Some or even most of the ore deposits in a given district may be on the flanks of the upwarp, but few major districts are located definitely on downwarped areas. Synclinal basins within certain limits of size appear to be unfavorable to the type of fracturing that admits ore-bearing solutions.

Jan 1, 1931

By A. E. Nehrenberg

R. A. Schmucker, Jr.—The writer wishes to point out that an acicular growth of austenite, similar to that described in the author's paper, was recently observed in an alloy steel of only 0.06 C content. This steel, which represents an 0.07 max C, 1.35 Cr, 0.55 Ni, 0.20 Mo analysis, combines the characteristics of minimum hardness in the annealed condition with maximum hardenability and is therefore suited primarily for cold-hobbing applications. The acicular austenite formation in this steel was observed accidentally during a determination of its Ac1 temperature. The samples used in this investigation represented as-forged bar stock which had been given a preliminary temper at 1300°F. The critical (Ac1) temperature was finally established at 1400 °F. Fig. 15 represents the microstructure of the sample which had been heated at 1450°F for ½ hr, water quenched, and tempered at 600°F for ½ hr (for the purpose of darkening the martensite). It will be observed from the distribution of the darkened areas of martensite that the parent austenite grains formed at 1450°F had grown in an acicular manner and still occupied only a small percentage of the total area. The remainder of the area contains the original equiaxed ferrite grains in which new austenite had as yet scarcely formed. However, the tiny isolated martensitic patches at several points where three or more ferrite grains intersect indicate that small austenite grains had formed and started to grow in an apparently equiaxed fashion. Fig. 16 represents the prior microstructure of an original sample in the as-forged and tempered condition, before it was heated -above the critical temperature. It is probable that there are two kinds of ferrite in this structure: (1) The equiaxed proeutectoid ferrite grains which separated from the austenite when the steel was cooled from the forging temperature, and (2) the acicular ferrite associated with the aggregate of fine carbide which is represented by the patches of

Jan 1, 1951

By Frank Speller

WE are here to honor again the memory of Henry Marion Howe, one of the foremost metallurgists of his time, and it is indeed a great privilege to be called upon by the Board of Directors of .this Institute to give the memorial address this year. Professor Howe started active investigation of corrosion of iron from a metallurgical standpoint in 1887, and made several important contribu-tions to the subject from 1895 to 1908.(1) ? The papers named in the bibliography are only a few of his valuable papers, but in all his works he sets a high standard of scientific accuracy, together with a clearness and power of expression rarely equaled in engineering literature. There-fore it seems appropriate on this occasion to review the work on corrosion of this distinguished gentleman and then endeavor to make a brief inventory of what has been accomplished since his time. Howe saw the beginning of the steel industry in America and before he died (May 14, 1922) witnessed it develop to a production of 45,000,000 tons per year. He was naturally very much interested in the infant industry and was quick to see the importance of the question of corrosion. It was my privilege to discuss the subject of corrosion frequently with Professor Howe at various times from 1905 to 1908; in this, as in other metallurgical problems, he sought the truth without bias and always insisted on proving an opinion or conclusion before accepting it. We should remember that when Howe started his investigation of corrosion, in 1887, steel was rapidly supplanting wrought iron. Certain papers in the early eighties (now forgotten) claiming much greater durability for wrought iron than for steel aroused Howe's interest. He could not reconcile the statement that steel was intrinsically and incurably less durable than wrought iron with the continued and widening use of steel,

Jan 1, 1934

By B. F. Fackenthall

The Durham Iron Works of Messrs. Cooper & Hewitt, near Riegelsville, Pa., occupy a site which has been almost continuously the scene of iron-manufacturing industry since 1727. Doubtless if Anthony Morris and his thirteen associates, who in that year erected a blast-furnace on the Durham Creek, a short distance above where the Durham Iron Works now stands, could have had a vision of the improved and enlarged apparatus of their successors, they would have been not less astonished by the huge stack, the hot-blast ovens, and the blowing-engines of the modern blast-furnace, than by the railroad which now follows the bank of the river on which their clumsy " Durham boats " once floated pig-iron to Philadelphia. In one particular, posterity must confess their snperiority. We are told that in November, 1728, they shipped three tons of Durham iron to England. The proprietors of the Durham Iron Works are not now shipping iron to England. The present Durham furnace was built (in place of two smaller ones) in 1874 and 1875, and made its first blast in 1876. A description of it, with other works of the same proprietors, at Trenton, N. J., by A. L. Holley and Lenox Smith, was published in London Engineering for January 31st, and February 21st, 1879. Since that time, a number of improvements, dictated by experience, have been made in the details of the furnace and fittings; and the recent roilclusion of a long and successful blast presents a convenient opportunity for a description of the works and a statement of the results of practice. The accompanying drawings will show the general arrangement of the works. The furnace, Plate I., Figs. 1 and 2, is 75 feet high by 19 feet bosh. The hearth is 11 feet 4 inches in diameter, with seven tuyeres 5 feet 6 inches above hearth-line. The tuyeres project 9 inches into the furnace, making the interior tuyere-circle 9 feet 10 inches in diameter. The front is a modification of Luermaun's

Jan 1, 1886

By J. L. Brimhall, R. A. Huggins

The structure of deformed internally oxidized alloys of siluer- cotztcrining magnesium and copper-containing aluminum in was studied by thin-film transrrzissiotz electron microscopy. With low to moderate amounts of stvain, the deformation structure in t11e dispersion-hardened alloys was found to consist of a high density of dislocations arranged it a random distribution or in a very fine, but poorly defined, cell stucture, depending on the fitness of the dbsbersion and amount of deformation. 112 contrarst, both pure copper and silver show relative1y Large, distinct cell structures. The particular structures in the alloys are believed to result from particles acting as both dislocaliot~ sources and deflector-s. The Inck of a pvorzolrr~ced deformation texture tr~ regiotzs qf' seoere loctll plastic curvature after heavy deformation can also be traced to the formation of clislocntions on many slip systemes and a lack 01 local concentrations of dislocations of predominantly one sign. THE presence of fine dispersions of a second phase has long been known to have a strong influence upon the mechanical properties of solids. Until recently, the influence of particles on the deformation mechanisms has been assumed to be solely that of barriers to dislocations. This is seen in the classic models of edge dislocations being restrained by the particles.1 4 There is, however, considerable evidence that this is not their primary effect, and that the particles can have a large influence on the defect structure generated by plastic deformation. The presence of particles causes changes in the surface topography observed after deformation. In overaged precipitation-hardened materials containing hard, noncoherent precipitates, fine intersecting slip lines are found after deformation of single crystals. indicating the activation of many slip systems. This has been extensively observed in the A1-Cu systen;, both by optical microscopy and replica electron microscopy.'"13 In some of the observations. the slip lines were seen to extend between the particles. Similar observations of extremely fine slip lines or the apparent absence of normal slip lines have also been found in A~-M~."

Jan 1, 1965

By Portland P. Fox, Berlen C. Moneymaker

The development, within recent years, of core drills capable of drilling holes up to 72 in., or even more, in diameter, has made possible an entirely new and valuable method of geologic exploration. Although little used until recently as an exploratory tool except in the United States, by the Tennessee Valley Authority and the Corps of Engineers of the U. S. Army, for the exploration of damsites, the large-diameter core drill may be used to good advantage in other types of geologic exploration. Its principal utility is that of supplementing, rather than replacing, other means of exploration. Although core is frequently recovered intact, the greatest advantage of large-diameter drilling is that the holes produced are large enough to be entered by the geologist and engineer, and thus afford an excellent means of examining undisturbed rock. The walls of the holes are smoothly cut, and in some rocks nearly or quite polished, so that the most minute details of structure and stratigraphy are clearly disclosed. Such features as faults, joints, bedding planes, weathered "seams," and beds or layers of soft materials, which are not always amenable to disclosure by cores recovered from small-diameter holes, are conspicuously displayed in the walls of large holes. Frequent reference to the drilling of large-diameter holes is made in engineering literature, but comparatively little emphasis has been placed on their value in geologic investigation. It is, therefore, intended that the present paper acquaint the geologist, as well as the engineer, with the large-diameter core drill and the technique involved in its use, and also with its advantages, disadvantages and limitations as an implement of geologic exploration. The Equipment The equipment generally employed in the drilling of large-diameter holes consists of a trunnion-type drill head mounted on a sliding base, which allows it to slide clear of the hole and thus permit the introduction

Jan 1, 1941

By Clarence E. Jackson, George G. Luther

The ever increasing array of information concerning the measurement of the effect of the welding process on the properties of a steel is an indication of the tremendous effort that is being expended in this field. The methods that have been considered may be divided into two groups: first, those that measure directly the effect of welding on the ductility of a steel, and, second, those that observe the change in some property, such as the hardness of the heat-affected zone, and assume a direct correlation between this change and the resultant ductility. The nick-bend test is a direct method designed for studying the effect of welding on the ductility of a steel. The test specimen (Fig. I) consists of a bar cut from a plate with a bead weld on the surface. The specimen is prepaxed with a saw-notch placed so as to restrict deformation to the heat-affected zone under the bead weld when tested as a static bend. Failure is caused by rupture of the low-ductility metal in the heat-affected zone. The angle at maximum load is used as an index of the effect of the welding process on the material. In the development of the nick-bend test considerable scatter was noted in some of the results, although the agreement of duplicate specimens welded at the same time and tested consecutively was excellent. Upon further investigation it was found that the change in ductility was dependent upon the interval of time between the welding operation and the testing of the specimen. For the six steels of Fig. 2, the angle at maximum load in lour cases was doubled and in one case was tripled. All steels that have been studied show an improvement in the angle of bend for longer intervals between welding and testing. This same behavior has been found in weldability tests using the Navy T-bend

Jan 1, 1945

By S. A. Montague

Mica can claim a considerably greater importance than would be assumed from its comparatively small dollar volume, which came to about $37,000,000 for the United States industry as a whole in 1957. Mica is one of the strategic minerals. We must depend on imports from distant sources for virtually all of our requirements of high grade block and all of our mica splittings. Mica is essential and indispensable for vacuum tubes and high-performance condensers, two electronic components which are vital military necessities besides being nearly indispensable to civilization today. Composition and Properties Mica is the general name for a group of some nine different minerals, two of which, muscovite and phlogopite, are the minerals used by the mica industry as its raw material. Several of the other varieties are commercially useful-vermiculite, * used for heat insulation in expanded form, and lepidolite, used as an ore of lithium while the others-biotite, roscoelite lepidomelane, paragonite and zinnwaldite have little or no commercial importance. Biotite frequently occurs as an undesirable impurity in muscovite. Table 1 lists various properties and other data concerning muscovite and phlogopite. Chemically, mica is a complex silicate of sodium, potassium and aluminum. Most varieties of muscovite are higher in sodium, and of phlogopite in magnesium. There are no important uses of mica where the chemical analysis is important, except that in some uses of ground mica, the content of iron oxide present as an impurity must be kept to a very low limit. Muscovite occurs in a range of color from the so-called India "ruby" which is more closely a pinkish brown, to light and dark green, with numerous other intermediate shades. Ruby color is usually preferred by industry, especially in the better qualities. When split very thin the color in most [ ] micas disappears. Muscovite mica is frequently found containing black and red "stain" as a homogeneous part of the books or sheets. In most cases this stain or impurity is magnetite

Jan 1, 1960

By S. L. Hoyt

Some of the more important properties of finished materials are strength, ductility, toughness, resistance to alternating and repeated stresses, etc. Of these, the property that appears to have received the least consideration, at least in this country, is toughness, which is due, possibly, to our regarding toughness as a qualitative property or, at any rate, as one that parallels ductility. This arises out of our greater experience with the simple carbon steels in the rolled or forged (non-heat-treated) condition which, qualitatively, are tough if ductile and are not tough if brittle. In this way we have erroneously become accustomed to judging the toughness of a material from its behavior in the tensile or similar test. The point of view presented in the present paper is that toughness, like hardness or tensile strength, should be regarded as an independent property and of sufficient importance to require, in so far as that may be possible, quantitative determinations. If such be true, it becomes at once necessary to devise experimental means for measuring or valuating toughness, and the notched-bar impact test (the Charpy test) is advanced as the most logical test that has so far been developed for this purpose. It is further advanced, with particular emphasis, that we have two kinds of toughness to deal with and, accordingly, they will be dealt with independently. Classification of Materials According to Toughness Toughness has been defined somewhat as follows: Tough materials are those that offer considerable resistance to permanent deformation but which, once such resistance has been overcome, may be deformed plastically, but only by the expenditure of considerable energy. In other words, tough materials may be deformed plastically but they absorb a considerable amount of work in the process. This kind of toughness may be called "static" toughness when the rate of loading is reasonably slow or "dynamic" toughness when the rate of loading is comparatively rapid, as in impact testing, but in all cases the stress distribution is essentially uniform. However, static toughness does not

Jan 1, 1920

By Chester T. Sims, Robert I. Jaffee

The thermoelectric behavior of the Pt—Pt-Re thermocouple and the resistance of rhenium to attack by certain molten metals is discussed. In addition, data are presented on the stress-rupture behavior of drawn wire, the tensile characteristics of rolled sheet, the variation of Young's modulus with temperature, and the effect of specimen size and fabrication method on the work harden ability. Mechanical properties of thoriated rhenium are discussed. This includes data on the effect of thoria in rhenium on tensile properties, ductility, work hardening, and recrystallization. RECENT work by the authors', has described methods of fabrication and some of the physical and mechanical properties of rhenium. Rhenium was established as a high melting, dense, refractory-type metal with favorable mechanical properties. In addition, Todd and co-workers' and others" have studied such properties of rhenium as the work function, specific heat, and the resistance of rhenium to the water cycle. Revelation of these and other properties has led to serious consideration for application as electrical contacts, high temperature thermocouples, and wear resistant materials. chanical properties reported previously,' several additional examinations have been conducted. The stress-rupture behavior and the Young's modulus of rhenium have been investigated at elevated temperatures. Tensile data have been obtained for rolled sheet, and a study of the relative work hardening characteristics of rod, wire, and sheet has been conducted. Variation of Modulus of Elasticity With Temperature—The Young's modulus of a % in. diam annealed rhenium rod was determined from room temperature to 880"C (1620OF). The rod, approximately 6 in. in length, was activated in a transverse vibration apparatus suspended in a furnace. The resonance frequencies of the rod were measured and used to calculate the moduli values. The driven frequency was 569 cycles per sec, and a protective helium atmosphere was used. The data, plotted in Fig. 1, show that the modulus decreases in an approximately linear manner with temperature over the range tested.

Jan 1, 1957

By Thomas L. Kesler

IF all of the 14 million tons of kaolin produced in Georgia through 1949 had been mined from a single deposit 20 ft thick, it would represent a mined-out area of less than 1 sq mile. This measure of depletion is in such strong contrast with the large size of the area shown in Fig 1, from which most of the output has come, that there has developed an optimistic outlook concerning future supplies of kaolin equal in grade to that already mined. Dozens of mines are widely but not evenly distributed within this area, which consists mostly of parts of Twiggs, Wilkinson, and Washington Counties. There are scarcely half a dozen kaolin mines elsewhere in the state that have been appreciably productive, although the areas in which they occur may have good possibilities. Most of the efforts to find new deposits, therefore, will be confined to the area shown in Fig 1, for it is here that the industry has established its facilities, and prospecting is encouraged by relatively numerous outcrops and opened deposits of kaolin. The Ounulgee and Oconee Rivers drain the area. They and their main tributaries have flat, swampy flood plains covered with alluvium and for the most part thickly wooded. The divides between these streams are intricately dissected by the minor tributaries, which are spring-fed in steep-walled, cirquelike heads. Gullying and undercutting are active along the streams but are partly controlled by unusually dense vegetation. The mean altitude is about 350 ft above sea level and locally the relief ranges up to 200 ft. The area is near the inner margin of the Coastal Plain, and is underlain by Cretaceous and Tertiary formations. Its general location is shown in black in Fig 1. The division between the Coastal Plain and the Piedmont Plateau is actually a very sinuous line, the fall line, marking the extent to which erosion has stripped the Coastal Plain sediments from the southeastward- sloping surface of the crystalline rocks of the Piedmont.

Jan 1, 1952