Search Documents

By Alexander L. Holley

THE 400-ton testing machine, ordered in June, 1875, by the United States Board appointed to test "iron, steel, and other metals," has lately been completed at the Watertown Arsenal, thoroughly proved and accepted by the Board. The excellence of the machine in every respect is more than satisfactory, and its accuracy is at first sight astonishing, although an investigation of its principles must show that if the weighing apparatus will weigh at all, it must do so with perfect accuracy, because all its movements are absolutely without friction. The proof experiments were numerous, and the effects of recoil after sudden ruptures at maximum loads, were watched with great care, but without much anxiety, because the weighing parts affected are by no means delicate in structure, and their motion is almost infinitely small. Among the tests were the following : A forged link of hard, wrought iron, 5 inches in diameter between the eyes, was slowly strained in tension, and broke short off with a loud report at 722,800 pounds. The diameter before breaking at the point of fracture was 5.04 inches; after breaking, 4.98 inches. In order to see if the weighing parts had been disturbed by the recoil, which was obviously near the greatest recoil the machine will ever suffer, a horse-hair was next tested ; it was 7-1000ths of an inch in diameter; it stretched 30 per cent., and broke at 1 pound. Other horse-hairs vary in tenacity between 1 and 2 pounds. Of course, the accuracy of the machine on such delicate specimens, and indeed on specimens having some hundreds of pounds tenacity, has been checked and proved by other weighing machines. A 5-inch round bar, turned down to 3 5/8 inches diameter along the centre, was pulled apart at 430,200 pounds tension. Then some more horse-hairs were tested ; also copper wires 19 1/2-1000ths of an inch in diameter, which averaged 25 pounds tenacity..

Jan 1, 1879

Future of State and Federal Oil Regulation. BY NORTHCUTT ELY (Trans , vol 118 2400 words) The Interstate Oil Compact, ratified by six states and Congress in 1935, replaced the petroleum code, invalidated with other codes by the Schechter decision This compact endeavors, first, to conserve reservoir energy of oil pools through substantially uniform conservation measures by the states, second, it recognizes the state rather than the Federal Government as possessing the necessary police power for that purpose, third, it establishes an interstate advisory commission, so that orderly production in one state is not penalized by uncontrolled production in another, fourth, Federal interests are recognized in the control of hot oil, regulation of imports and fact-finding forecasts of supply and demand by the Bureau of Mmes It is not as complete an instrument as proposed by the Federal Oil Conservation Board in 1932, but is workable, and will be effective in proportion to the support given it by the industry Three results may follow First, now that fear of Federal control has subsided, the industry may lose interest in the compact and let it fall to pieces, second, if vigorously supported by the industry, the compact can accomplish most of the conservation objectives sought by the Federal control measures now believed unconstitutional, third, if the Compact fails, Federal regulation is almost certain to be revived, and can probably be sustained in connection with neutrality legislation, regulation of interstate pipe lines, and coordination of Federal and state gasoline taxes Nearly every step toward governmental regulation has originated within the industry state proration, the Federal petroleum code, Federal control of imports, Federal control of hot oil are examples The Compact shows a trend toward coordination between the powers of the industry, the state government, and the Federal Government If this arrangement fails through lack of interest by the oil industry, the next step is likely to be absorption by the Federal Government of the other two factors involved in the situation

Jan 1, 1937

By Waldemar Lindgren

During the last 15 years much attention has been given to the " contact-metamorphic" ore deposits which mainly occur in limestone close to intrusive contacts. In general, these deposits are characterized by the association of magnetite and simple sulphides with the so-called L'contact-metamorphic" silicates. These silicates comprise garnet, epidote, vesuvianite, tremolite, wollastonite, diopside, hedenbergite, ilvaite, and many other rarer forms. The contact-metamorphic zones contain also in places minerals with boron, fluorine, and chlorine, like axinite, tourmaline, danburite, fluorite, and scapolite. There is also more or less quartz and coarsely recrystallized calcite. The simple sulphides embrace pyrite, pyrrhotite, chalcopyrite, galena, zincblende, more rarely arsenopyrite. On the whole, sulphantimonides and sulph-arsenides are rare. Deposits of magnetite or chalcopyrite or of both are most common. The deposits have an irregular or rudely tabular form, following main contacts, dike contacts, or stratification planes; they rarely extend for more than 1,500 or 2,000 ft. from the contact; far more commonly they only reach a distance of a few hundred feet from that surface. The deposits are usually formed by replacement of limestone, or allied calcareous rock. Apparently they are found both in relatively pure and in impure carbonate rock. The deposits are geoiogical bodies of a chemical and mineralogical character differing greatly from the adjoining intrusive rock and from the unaltered limestone. They are rich in silica and iron, with more or less of lime, magnesia, alumina, sulphur, and rarer metals like copper. The so-called contact-metamorphic silicates which form the gangue usually are coextensive with the metallic minerals, though of course not necessarily with the merchantable ore. All opinions agree in holding the deposits of epigenetic origin, later than the inclosing limestone. Regarding the origin of the metals and the genesis of the ores there are several opinions. 1. There are those who see in these deposits the result of concentration of material contained in the intrusive rocks by means of hot circulating

Jan 1, 1915

By H. T. Mercer, A. C. Paulson

The composition of steel and the theory of its heat treatment have been so ably discussed elsewhere that it is unnecessary to go into the subject here. The purpose of this paper is to describe briefly the method of treating drill steel at the Copper Range mines, giving some of the troubles encountered and the manner in which they were overcome or corrected. To study the matter properly, it was necessary to devise a system of records that would show the actual underground performance of the drills. To illustrate this system, the records of the Champion mine are used, as it is at this mine that most of the work along these lines has been done. Reports from each drill machine are made daily by the shop and mine, and tables compiled from these reports show the footage drilled, steel broken, drills received and sent out at the shop, drills sharpened, and bits cut off. These data show what each machine or party is doing and whether the miners' supply of drills is kept up to date. There have been times when the supply of drills has been short and time lost by the miner in looking for drills. The daily records show the number and condition of drills on hand at all times. Under the old method of sharpening, the drills were heated in a coke furnace, the proper degree of heat being judged by color. Then they were sharpened in a machine, reheated in a second coke furnace where the proper heat was again determined by color, and quenched in water. While this method was fairly successful in the hands of a careful workman and for the solid steel used in the old piston drill machine, the introduction of the faster water machine, using hollow steel, produced changes both underground and in the shop. Much more was expected of the hollow-steel and hammer-type machine, with its improved method of rotation, but troubles due to breakage, burnt bits, uneven tempering, etc., at once appeared.

Jan 1, 1922

By Gerald V. Jergensen

Does an idea have merit? What does it cost to implement? Can the concept be implemented successfully? The ultimate proof is to try, then see. However, when there are many millions of dollars at stake, blindly building and trying requires considerable courage. Owners and investors in retrospect might choose other less complimentary words. So we might ask, "How might we establish the feasibility of an idea or concept before committing large sums of money to the ultimate test?" From this basic and prudent question, has evolved the engineering concept of the feasibility study. A feasibility study is simply a systematic evaluation of an idea or concept to determine the prospects for success. In a literal sense, a feasibility study considers an idea in terms of its data base, "builds" the idea on paper, "operates" that idea, calculates the cost and benefits, then measures the probable success in terms of some economic, technical or financial standard. Feasibility studies can be quite modest in scope yet provide useful insights as to the viability of an idea. A study might be initiated only to examine the completeness or validity of the metallurgical data base. Another study could be a search for a workable idea or solution to an already-identified possibly troublesome problem. In this latter case, the question, "Will it work?" may be far more important than, "How much will it cost?" Feasibility studies are sometimes global in scope, involving several dozens of specialists and examining an entire "grass roots" mining complex. Other studies may be less ambitious but equally important in examining an expansion proposal or developing new operating techniques. Studies may be commissioned to remove plant bottle-necks, solve maintenance problems and so on. The terms study and feasibility study are used interchangeably in this chapter. They denote a systematic method to examine a proposed concept or idea. DATA BASE Typically, studies are initiated with a minimum amount of specific information and a maximum number of assumptions. As the work proceeds and the data base expands, assumptions are replaced

Jan 1, 1982

By J. E. Korski

Quebec Cartier Mining Co. operates a low-grade iron ore deposit at Lac Jeannine, Que., which is located at the extreme southwestern end of the Quebec-Labrador Trough (Fig. 1). The facilities there include one of the world's largest concentrators, a hydroelectric plant of 60,000 hp, and the modern town of Gagnon. A 191-mile railway connects the mine to the seaport situated at Port Cartier on the St. Lawrence River. The harbor in Port Cartier can accommodate both lake and large ocean- going vessels and is also the site of a major grain terminal. The concentrator in Lac Jeannine is designed to produce some 8 million tpy (tons per year) of specular hematite concentrate, containing 66% Fe, from approximately 20 million tons of crude ore. An annual stripping program of 5 to 8 million cu yd of waste rock uncovers the required ore. Approximately 100,000 tons of ore and waste are removed daily on a year-round, 24-hr-per-day basis. The open pit covers an area with maximum dimensions of 8,000 x 2,600 ft (Fig. 2). Present mining plans call for an ultimate depth of approximately 1,000 ft below original ground level. The rocks in the pit area are typical of this portion of the Grenville geological province. They consist largely of marble, quartz rock, pegmatite, iron formation, and stratigraphically older gneisses. The iron-ore formation consists of medium to coarse-grained specular hematite in a quartz host rock. The formation occurs locally in a plunging, anticlinal form. The topography in the vicinity of the mine is rolling, with maximum variations in elevation of about 400 ft. The hills are thickly wooded with birch, black spruce, and some tamarack. Lakes and muskeg areas are plentiful. Precipitation and temperature records have been kept since 1959. The annual rainfall has ranged between a low of 23 in. and a high of 42 in.

Jan 1, 1969

By David B. Rushmore

Torches were used by the early Romans for mine-lighting, and these were followed by open lamps or earthen jars filled with tallow or oil, and later by candles. In early coal-mining, explosive gases seldom occurred, and, if they were encountered, the danger of explosion was materially diminished by the absence of any ventilating-system and the consequent insufficient circulation of air to form with the methane an explosive mixture. As the art advanced, the danger of fire-damp became more apparent, and methods for testing the air were resorted to as early as in the fifteenth century. The method of testing consisted in lowering a dog in a basket down the shaft. As soon as he encountered fire-damp he would commence to howl, after which he was withdrawn, and a leafy bush was fastened to the end of the rope and run rapidly up and down the shaft. This so disturbed the accumulation of gas as to cause it to rise out of the shaft. Later this odd method of testing was improved upon through the discovery that a light inserted in a body of fire-damp Gould produce a blue flame. Candles were used for this purpose, and, when fire-damp was thus discovered, brushing or some other primitive method of fanning was resorted to for driving out the gas. In some instances the gas was burned away, regardless of the danger thereby incurred. A man, wearing a well-moistened coat and a mask with glass spectacles, descended in the mine a few hours before each shift. With a long stick, to which was fastened a burning torch or candle, he would crawl on the floor with the stick so raised that the light would sweep the roof and ignite the gas which it encountered. In this position the flame of the explosion would pass over him, after which he would retreat from the gases resulting from the combustion. The occurrence of serious accidents resulted in

Jan 1, 1913

By Frederick V. Lawrence

Broadly speaking, fluxes are substances which promote wetting and spreading or enhance the fluidity and manipulative properties of materials in joining, fusion, and smelting operations. The term most strictly applies to substances used to facilitate soldering and brazing; but in .he discussion which follows, the definition will be broadened to include materials used to promote fusion in arc welding and which aid in he smelting of metals. In each of the mentioned applications, the role of flux and its composition differs considerably; consequently n the discussion which follows, fluxes for soldering, brazing, arc welding, and smelting applications will be considered separately. Soldering and Brazing Fluxes Soldering and brazing are metallurgical joining processes in which a joint is formed using a filler metal of composition dissimilar to that of he joined pieces (base metal). The filler metal, older or braze, is always of lower melting point than the base metal. Consequently with these) recesses there is no melting of the base metal. The successful creation of the joint depends upon the wetting and spreading of the solder or braze around or throughout the joint. The obstacles to successful soldering and brazing are contaminants and tenacious oxide films on the metal surfaces. In soldering and brazing applications, fluxes act to remove and exclude oxides and other impurities from the joint. There is no fundamental difference between soldering and brazing. The distinction between them is made on the basis of temperature. Joining operations carried out at temperatures above 500°C are termed brazing. The higher temperatures used in brazing enable higher melting point filler metals to be used which generally provide stronger joints. The higher temperatures of brazing processes also require fluxes which are substantially different from those used in soldering and which will remain effective at high temperatures. Consequently the distinction between soldering and brazing can also be made on the basis of the fluxes used.

Jan 1, 1975

By H. L. Hartman

The past 15 years have seen rapid advances in the metallurgy of materials for drill machinery and bits, but rock drilling itself continues to be largely an art. Jet piercing, roller bit rotary drilling, and rotary percussion are all promising new techniques, but the percussion rock drill, still used for 90 pct of the blastholes in U. S. hard-rock mining, has undergone no major modification since pneumatic machines were first used successfully in the 1860's. This singular lack of progress stems directly from ignorance of the nature of impact failure of rock and the fundamentals of rock penetration in general. For nearly three-quarters of a century, mining engineers did not know what went on at the bottom of a drillhole. More and more, in recent years, investigators in the field have come to realize that to understand percussion drilling they must study the basic action of percussion bits penetrating rock—not the per- formances of commercial rock drills, with their many attendant variables that cannot be isolated or controlled. Using a vertical drop tester, the writer investigated the sequence of rock failure under the impact. of a simple, chisel-shaped bit when changes were made, singly, in significant variables. Results of this and other research are reported here. BASIC CONCEPTS The formation of a crater in rock under the impact blow of a bit can be observed experimentally. Directly beneath the edge of the bit the rock is crushed into fine powder; toward the sides of the crater it chips out into relatively large fragments. An explanation of these phenomena has been offered by Drilling Research Inc. on the basis of work sponsored by this organization at Battelle Memorial Institute (Ref. 1,1954, Summary, pp. 9-18). High-speed photography and force waveforms obtained from strain gages mounted on the bit near the cutting edges recorded the sequence of events in crater formation with a die-shaped or blunt, wedgc-

Jan 1, 1960

By C. S. Smith, E. W. Palmer

For several years an investigation has been in progress in the research laboratory of The American Brass Co. to determine the thermal and electrical conductivities of most copper alloys of commercial importance and several of scientific interest. This paper contains such data on the binary alloys of copper with silicon, aluminum, manganese and nickel, and on a large number of ternary or more complex alloys. Some interesting general relationships between the thermal and electrical conductivities for all copper alloys at all temperatures are pointed out. The data for the copper-zinc, copper-phosphorus and copper-tin binary systems have already been published1,2 † except for the electrical conductivity at 200" C., which is given in the appendix of this paper. Literature on Thermal Conductivity of Copper Alloys The papers referred to above contained a summary of the figures available in 1929 for the thermal conductivity of copper alloys. There is given in Table 1 herewith a selection of the data that have appeared since that time. The measurements of Hanson and Rogers3 are particularly interesting since they cover a series of alloys in the alpha solid solution range and show the effect of heat-treatment. Their alloys were tested as annealed castings, and are not therefore directly comparable to the worked alloys measured in the present investigation, although the difference is small. Bailey's determinations4 were carried out on the alloys used by Lees6 in 1906, and extend his results to higher temperatures. It is most unfortunate that the alloys were not analyzed, for the approximate compositions given are hardly sufficient identification of the material. It is equally to be regretted that neither Hanson and Rogers nor Bailey give data for the electrical conductivities of their samples. Sager6, using the heat-wave method of King, determined the thermal conductivity of copper, nickel and four alloys of the two metals. His results are included in Table 1.

Jan 1, 1935

By D. L. Katz

In the management of oil properties, it is always desirable to know the future behavior of oil wells and oil reservoirs. Some estimation of the quantity of oil and gas that will be produced must be made as a basis for decisions on possible returns on investments in lifting equipment, drilling of additional wells, and other operating expenditures. In new or wildcat areas, operating expenditures are considered highly speculative, but in the completion of partly drilled and the operation of producing fields it is good business to remove as much speculation as possible. An accurate knowledge of oil and gas reserves in such cases would solve many management problems. The term "oil reserves" usually signifies the future ultimate recovery without specifying the method of production. Thus with changing methods and innovations in the production industry, reserves of any definite reservoir may be increased by increasing the portion of oil recovered. The usual reserve estimates are made by comparisons of well and formation characteristics, by using a percentage recovery on the oil content of the formation volume using porosity data, by extending production curves on non-prorated wells, or by extending bottom-hole pressure-production curves. The most reliable method would appear to be one that would estimate the initial quantity of oil and gas present and then obtain percentage recovery values for various productive methods and formations from experience. It is the purpose of this paper to describe a method of estimating the initial quantity of oil and gas present in a reservoir. The method is based on field operating data and the properties of crude oil-gas mixtures. The principles involved, the data required, the assumptions necessary, and an example of the method will be given. The method is entirely independent of sand volumes and formation porosities. Principles of Method The method of estimating the initial quantity of oil and gas present is based upon the premise that the volume occupied by oil and gas in the reservoir is constant and that a mixture of crude oil and gas will behave in

Jan 1, 1936

By C. D. Rubert, W. J. Parton

Large quantities of fine anthracite with associated impurities are discharged with the waste water from the coal-cleaning plants in the Pennsylvania anthracite region. Furthermore, for many years this fine material has accumulated and formed silt banks. The difficulty of removing the impurities from the fine material and the lack of adequate markets are responsible for the waste of this material. In view of a larger demand for fine coal, mainly for pulverized fuel, the Lehigh Navigation Coal Co. Inc. decided to investigate the froth flotation process for recovery of fine coal from these waste solids. A test plant was constructed and operated for six months during 1942 in order to determine the practicability of recover ing coal from the waste water of a a plant (breaker) by froth cleaning and to obtain operating data for designing a commercial plant if the results were favorable. Preliminary Investigation Before the pilot plant was constructed information was obtained by field and small-scale laboratory tests to serve as a guide in the design and operation of the pilot plant. Size and ash analyses of a representative sample of the material discharged in the wash water from a cleaning plant are given in Table. The refuse content increases progressively as the size of the particles decreases The larger particles (+35 m.) are low in ash content and could be marketed without cleaning. Since these solids are discharged from the breakers with 90 to 95 per cent water by weight, the first step in the recovery of the coal was that of reducing the quantity of water so that water in excess will not have to be handled. Furthermore, it was found that the removal of most of the minus 200 mesh high-ash material was desirable to permit the most efficient flotation of the cod. Classification tests were run and showed that a hydroseparator overflow rate of 12 ft. per hour* was sufficient to elimi-,late much of the minus 200-mesh material while allowing the coarser material to settle and be thickened,

Jan 1, 1944

By C. D. Rubert, W. J. Parton

Large quantities of fine anthracite with associated impurities are discharged with the waste water from the coal-cleaning plants in the Pennsylvania anthracite region. Furthermore, for many years this fine material has accumulated and formed silt banks. The difficulty of removing the impurities from the fine material and the lack of adequate markets are responsible for the waste of this material. In view of a larger demand for fine coal, mainly for pulverized fuel, the Lehigh Navigation Coal Co. Inc. decided to investigate the froth flotation process for recovery of fine coal from these waste solids. A test plant was constructed and operated for six months during 1942 in order to determine the practicability of recover ing coal from the waste water of a a plant (breaker) by froth cleaning and to obtain operating data for designing a commercial plant if the results were favorable. Preliminary Investigation Before the pilot plant was constructed information was obtained by field and small-scale laboratory tests to serve as a guide in the design and operation of the pilot plant. Size and ash analyses of a representative sample of the material discharged in the wash water from a cleaning plant are given in Table. The refuse content increases progressively as the size of the particles decreases The larger particles (+35 m.) are low in ash content and could be marketed without cleaning. Since these solids are discharged from the breakers with 90 to 95 per cent water by weight, the first step in the recovery of the coal was that of reducing the quantity of water so that water in excess will not have to be handled. Furthermore, it was found that the removal of most of the minus 200 mesh high-ash material was desirable to permit the most efficient flotation of the cod. Classification tests were run and showed that a hydroseparator overflow rate of 12 ft. per hour* was sufficient to elimi-,late much of the minus 200-mesh material while allowing the coarser material to settle and be thickened,

Jan 1, 1944

By A. C. Richardson

TROUGHS or launders are probably the oldest machines used for ore. concentration, and their development was suggested no doubt by the natural segregation and stratification of materials that take place in the bed of a stream. Trough washers for coal cleaning were first used in France and Germany about one hundred years ago and have been used in some form or other ever since. The early launders were intermittent or batch machines, and only comparatively recent developments have made them continuous. The chief disadvantage of early launder systems as applied to coal has been that when a satisfactorily clean: coal was produced the loss of good coal in the refuse was excessive. Other disadvantages have been the large quantities of water and the great lengths of troughs necessary to treat moderate tonnages of feed. One of the most widely used types of trough washers is the Rheolaveur, which has been developed in the last 25 years. Fig. 1 shows a more or less standard arrangement for fine coal. In this there are four troughs placed one below the other and sloped a few degrees from the horizontal. Rheo-boxes or draws are provided at intervals in the bottom of the trough for the removal of material deposited from the stream. These draws are spaced substantial distances apart. Some of the rheo-boxes are provided with upward currents of water to modify the horizontal current stratifica-tion. In operation it is the function of the first two troughs to remove all refuse material and permit only clean coal to be discharged over the end. In order to accomplish this, large quantities of coal are drawn through the rheo-boxes. The third and. fourth troughs are used to recover the coal discharged through the boxes of the first two troughs as a middling product and to discharge a clean refuse. The middlings are returned to the first launder and are usually about equal to 40 per cent of the raw coal being fed to the launder.

Jan 1, 1938

By D. L. Katz

In the management of oil properties, it is always desirable to know the future behavior of oil wells and oil reservoirs. Some estimation of the quantity of oil and gas that will be produced must be made as a basis for decisions on possible returns on investments in lifting equipment, drilling of additional wells, and other operating expenditures. In new or wildcat areas, operating expenditures are considered highly speculative, but in the completion of partly drilled and the operation of producing fields it is good business to remove as much speculation as possible. An accurate knowledge of oil and gas reserves in such cases would solve many management problems. The term "oil reserves" usually signifies the future ultimate recovery without specifying the method of production. Thus with changing methods and innovations in the production industry, reserves of any definite reservoir may be increased by increasing the portion of oil recovered. The usual reserve estimates are made by comparisons of well and formation characteristics, by using a percentage recovery on the oil content of the formation volume using porosity data, by extending production curves on non-prorated wells, or by extending bottom-hole pressure-production curves. The most reliable method would appear to be one that would estimate the initial quantity of oil and gas present and then obtain percentage recovery values for various productive methods and formations from experience. It is the purpose of this paper to describe a method of estimating the initial quantity of oil and gas present in a reservoir. The method is based on field operating data and the properties of crude oil-gas mixtures. The principles involved, the data required, the assumptions necessary, and an example of the method will be given. The method is entirely independent of sand volumes and formation porosities. Principles of Method The method of estimating the initial quantity of oil and gas present is based upon the premise that the volume occupied by oil and gas in the reservoir is constant and that a mixture of crude oil and gas will behave in

Jan 1, 1936

By James B. Graham, Earle E. Smith

The value of all minerals produced in the United States for the years 1930 to 1932 averaged $3,460,000,000 annually, according to Bureau of Mines reports. Of this amount, approximately $1,280,000,000 represents nonmetallic substances, such as petroleum, gas, sulfur and salt produced as fluids. Thus, about.37 per cent of the country's mineral wealth is procured through wells drilled in the earth, which require casing to keep them open throughout their life. Deep well drilling has increased greatly in the last few years. Several strings of casing have been set deeper than 9000 ft.—one, a string of 7?-in. O.D. casing, 10,301 ft. long, run in a well drilled by the Gulf Production Co. in West Texas, holds the record up to this time. These are longer strings than were contemplated when the American Petroleum Institute Specifications were adopted 10 years ago, therefore it is necessary to consider whether the present joint standards are adequate for such strings, or for even longer strings that may be called for in the future. Petroleum engineers are asking: Is there a possibility that stronger joints can be designed without going to stronger and more costly steels than offered in present specifications? Without sacrificing too greatly the tensile properties of the joint, can its design be changed to allow more clearance in the open hole below the next larger string of casing, and thus avoid costly underreaming? What can manufacturers offer for drilling through heaving shale? Fundamentals of the Problem During the last few years considerable study has been given to casing joints and their limitations, and since attention must be given to this subject by those who will be required to drill deeper holes, it is timely to review the fundamentals of the problem. These will be recognized generally as the following: 1. No threaded joint can be stronger than the area of metal under the root of the first perfect thread, and this area must be large enough

Jan 1, 1935

HAVING promised you to write concerning the nature of ores in particular, I must tell you some general facts, especially those concerning the places, kinds, and manner of their existence as well as the tools which are used. However, you must know that according to good investigators these ores are found in many parts of the world. They show themselves almost like the veins of blood in the bodies of animals, or the branches of trees spread out in different directions. Indeed, careful investigators of minerals, wishing to show by analogy how ores are located in mountains, have drawn a large tree with many branches, planted in the middle of the base of a mountain. From its principal trunk extend various branches, some thick, some slender, exactly like real trees in mature forests. They think that these grow and enlarge continually and draw themselves toward the sky, ever converting into their own nature the most disposed adjacent materials so that finally the tips arrive at the summit of the mountain and emerge with clear sign, sending forth, in place of leaves and blossoms, blue or green fumosities,* marcasites with small veins of heavy mineral, or other composition of tinctures. From these things, when they are found, it is possible to make certain inference that such a mountain contains ores, and as the signs are more or less, so are the minerals plentiful and rich or poor. For this reason the prospectors for these things take heart according to the manifestations that they find, and with hope and certainty of profit they take all possible pains to mine with skill and expense those things that the signs have indicated. Often there are ores of such a kind and quality that they raise a man in wealth to the skies. For this reason men penetrate with eyes of appraisal and judgment within the mountains and see almost exactly the places where there is ore and the

Jan 1, 1942

Large scale mining of Mesabi taconites may have moved nearer to realization with the arrival of the latest model Linde Jet-Piercing machine at Reserve Mining Co.'s Babbitt, Minn. property. When the machine is placed in operation it is expected to pierce blast holes in the hard taconite beds up to 10 times faster than is possible with existing drilling equipment. The new primary blast hole drilling machine has been designated the JPM-3, and is the successor to the JPM-1, in operation at Erie Mining Co.'s taconite mines at Aurora, Minn. The size of primary blast holes which can now be pierced has increased from a nominal 61 in. diameter to 71 in. diameter and maximum hole depth has increased from 35 ft to 47 ft. Development has progressed to where 71/2 in. holes can be pierced with the same speed as 61/2 in. holes. Piercing progress is controlled by electronic blowpipe descent controls. Other features of the JPM-3 include: automatic burner ignition from the operating cab; heated and air conditioned operating cab designed for all-year operation; mechanical improvements for sub-zero operation common to the Mesabi, and redesign of wearing parts for longer service with minimum maintenance. The 40-ton machine is self-propelled. Power, oxygen, and cooling water lines trail from the machine. Jet piercing is based on combustion products of oxygen and a liquid fuel such as kerosene. The flame, jetting from a burner at speeds of about 6000 ft per sec, disintegrates layers of spallable rock. The burner is cooled by water which is then directed through orifices around the periphery of the burner. The water changes to steam and carries the spallings out of the hole. The equipment used in Jet-Piercing is essentially a tractor-mounted blowpipe containing a combustion chamber and nozzle, which is in effect a miniature rocket motor, from which the supersonic combustion gases emerge to do their work.

Jan 1, 1952

By C. S. Smith, E. W. Palmer

For several years an investigation has been in progress in the research laboratory of The American Brass Co. to determine the thermal and electrical conductivities of most copper alloys of commercial importance and several of scientific interest. This paper contains such data on the binary alloys of copper with silicon, aluminum, manganese and nickel, and on a large number of ternary or more complex alloys. Some interesting general relationships between the thermal and electrical conductivities for all copper alloys at all temperatures are pointed out. The data for the copper-zinc, copper-phosphorus and copper-tin binary systems have already been published1,2 † except for the electrical conductivity at 200" C., which is given in the appendix of this paper. Literature on Thermal Conductivity of Copper Alloys The papers referred to above contained a summary of the figures available in 1929 for the thermal conductivity of copper alloys. There is given in Table 1 herewith a selection of the data that have appeared since that time. The measurements of Hanson and Rogers3 are particularly interesting since they cover a series of alloys in the alpha solid solution range and show the effect of heat-treatment. Their alloys were tested as annealed castings, and are not therefore directly comparable to the worked alloys measured in the present investigation, although the difference is small. Bailey's determinations4 were carried out on the alloys used by Lees6 in 1906, and extend his results to higher temperatures. It is most unfortunate that the alloys were not analyzed, for the approximate compositions given are hardly sufficient identification of the material. It is equally to be regretted that neither Hanson and Rogers nor Bailey give data for the electrical conductivities of their samples. Sager6, using the heat-wave method of King, determined the thermal conductivity of copper, nickel and four alloys of the two metals. His results are included in Table 1.

Jan 1, 1935

By J. B. Austin, H. H. Pierce

In developing a consistent picture of the thermal expansion of the commercial chromium steels, which cover a range of carbon contents, it is desirable to know the expansion in the limiting case of the binary, carbon-free, iron-chromium alloys. We have, therefore, determined the thermal expansion of a series of five special alloys, ranging in chromium content from 3 to 10.5 per cent, with not more than 0.03 per cent carbon, over a temperature range extending beyond the transformation region; this low carbon content enables us to draw reasonably reliable conclusions as to the behavior of the carbon-free system. Moreover, the measurements serve to determine the beginning and the end of the alpha-gamma transformation; and they emphasize once more the fact that a transformation temperature determined by any method in which the specimen is cooled at an appreciable rate is apt to be seriously in error, particularly if the metal contains a transformation-retarding element such as chromium or managanese. The lag, or undercooling, observed at the ? — a transformation is explained in terms of the influence of temperature on transformation velocity; the rather unusual shape of the ? loop is attributed to a change with temperature and with composition of the distribution of chromium between the alpha-iron and gamma-iron solid solutions. The exact composition of the alloys, which were obtained through the courtesy of Dr. W. Rohn, of the Heraeus Vakuumschmelze A-G., is given in Table 1. Determinations of the linear thermal expansion and of transformation temperature were carried out in the vacuum dila-tometer previously described,' using a rate of heating and of cooling of 3.0" to 3.5" per minute unless otherwise stated. Magnetic susceptibility, which was measured in studying the rate of transformation, was determined with a magnetic balance, which also has been described.2 Results and Discussion Thermal Expansion Coeficients.—Numerical values for the linear expansion coefficient, derived from a smoothed curve based on at least

Jan 1, 1935