Search Documents

By H. M. Morse

During the year 1942 there were 66 wildcats drilling in Mississippi. One cored in oil sand, the Macro Drilling Company's Longbell No. I in Clarke County, but as yet it has not succeeded in recovering the oil. These drillings broughi to light five salt domes, two of which had heavy oil showing; one drilled by the Magnolia Petroleum Co. in Warren County, and

Jan 1, 1943

By Donald B. Gillies

THE great source of iron ore for the furnaces of this country has been the Lake Superior district. Ore was first discovered there in 1844, and the first shipments made via the Great Lakes in 1852 to a furnace at New Castle, Pa. The stream of ore from that region increased slowly to exceed a million tons in 1873, and did not reach 10 million tons until 1895. By 1901 it exceeded 20 million tons, and in 1907 over 40 million tons. Total Lake Superior output through 1948 was about 2500 million long tons. Outside the Lake Superior district are the Southern district, including mainly Alabama, Georgia, Missouri, and Texas; the Eastern district of New York, New Jersey, and Pennsylvania; the Western district embracing Wyoming, Utah, and California.

Jan 1, 1949

By Charles Catlett

(Chattanooga Meeting, October, 1M.) THE terms " developed " and " undeveloped " are necessarily relative and cover a wide range; but the latter is here applied to cases in which the information at hand falls short of a clear demonstration of values, and conclusions must be reached from a study of the geological conditions of the particular deposit, interpreted in the light of similar and closely related deposits. Such an inquiry might be characterized as an effort to reach reliable conclusions from insufficient data. But the engineer engaged in commercial work finds himself often face to face with apparently such problems; and while he may realize with regret that a small amount of intelligent development would add enormously to the value of his conclusions, he is compelled to recognize the demand of a business situation for a prompt decision as the basis of immediate action. In a case within my knowledge, the question involved was the purchase of 50,000 acres of coal-land, and 10 days was the limit within which this question must be decided. Of course, it was impossible to make a satisfactory examination within that time; but the 'instructions were "to make the most complete examination and the most positive recommendation possible." Such instructions are often given; for, no matter how much time an investor may have, he is likely to put of his decision until the last moment, and then discover that he needs more light and advice. It does not follow that engineers, after full explanation and mutual understanding of the situation, should decline to undertake examinations thus limited. In the case just mentioned, while only the broadest view was possible, half the time available was sufficient to show that the property was a good purchase. The timber alone was subsequently resold for more than the entire purchase-price of the

Mar 1, 1909

By I. I. Gardescu

Rumania produced during 1936 some 62,500,000 bbl. of oil. Of this production, 99 per cent comes from an area running east and west along the southern foothills of the Carpathian Mountains just north of Bucharest. This almost rectangular area measures 20 by 40 miles and is located in the districts of Dambovita and Prahova between the cities of Targovigte to the west and Mizil to the east. The remainder of the production is about evenly divided between the oil fields north and east of Mizil in the Buzh district and those to the north on the eastern flanks of the Carpathian Mountains in the district of Baciiu. The Transylvanian Basin to the north and west of the Carpathian Mountains has produced to date only dry gas from its numerous salt domes. Bucsani Field The Bucgani oil field produced 15,600,000 bbl., or 25 per cent of the total production of Rumania in 1936. Bucgani is a deep-seated salt dome 7 miles south of the old Moreni oil field. A slight surface doming, not dissimilar to the topography observed on some of the oil fields of the Californian basin, called attention to the area. It is the southernmost oil field and, together with the deep-seated and prolific Boldesti field, points to the great oil possibilities of the deep-seated domes along the northern edge of the Rumanian plains south of the Carpathian foothills. The Government is the principal owner of the oil and gas subsurface rights in the areas south of the foothills. The acquisition of leases by the operating oil companies may be made either by application for an exploration permit, the company being assigned part of the acreage in case of successful wildcatting, or, if the area has already been declared as proven territory, through competitive bidding. A block of 164 acres was auctioned recently for $200,000, or $1200 per acre. The largest producer in the Bucgani oil field is the Steaua Romana, which produced 39.5 per cent of the total for the field. The Steaua Romana is a post-war company and 50 per cent of its shares are owned by the British Steaua and the Steaua Franpaise and the other 50 per cent by a group of Rumanian banks and by the Government. The Colombia,

Jan 1, 1937

By W. C. Williamson, J. L. Shugert

DUST control is receiving considerable attention today by most companies as is evidenced by the many articles, papers, and books written on the subject. ~~~t of the larger mining companies have given this subject close study and have established standardized methods of control. W. C. WILLIAMSON and J. L. SHUGERT, Members AIME, are Assistant Ventilation Engineers, Anaconda Copper Mining Co., Butte, Mont. San Francisco Meeting, February 1949. TP 2705 A. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received Jan. 17, 1949. Permissible Limits: The question of permissible dust limits has been considered by medical commit-ties and various national conferences. Dr. Lanza, of the Metropolitan Life Insurance Company, Dr. Le-roy U. Gardner, of the Saranac Laboratory for the study of Tuberculosis, and Dr. Pancoast, of the University of Pennsylvania, have been members of these committees. A statement included in reports of some of these committees is as follows: Concentrations to which the dust must be induced in order to be safe have not been absolutely determined. There is evidence that a concentration of more than five million particles per cubic foot of a highly siliceous dust is dangerous. Therefore, it may be stated that it is desirable to avoid counts of more than five million particles of dust containing free silica to a high percent in working places. Table I gives the safe limits adopted by several state industrial codes. Table I. Safe Limits of Dust Concentration Limit Million Particles State Per Cu Ft Cal~fornia Silica (less rhdn 10 pct) 50 Silica (10 pct to 50 pcr) 10 Sllica (more than 50 pct) 5 New York Frcc silica less than 10 pet by weight of rock formation 100 Frec silica more than 10 Pct by weight of rock formation 10 Oregon Silica (over 40 pct) 5 Silica (20 to 40 pct) 10 Silica (10 to 20 pet) 20 Wisconsin 15 million particles, under 10 nicrons in longest dimension per cu ft of air, when the quartz content of the dust is 35 pct, variations in free silica content will make proportional inverse changer in this standard Close attention to dust concentrations has been given to mining operations, since these operations are frequently carried on at considerable distances

Jan 1, 1951

By J. L. Shugert, W. C. Williamson

DUST control is receiving considerable attention today by most companies as is evidenced by the many articles, papers, and books written on the subject. ~~~t of the larger mining companies have given this subject close study and have established standardized methods of control. W. C. WILLIAMSON and J. L. SHUGERT, Members AIME, are Assistant Ventilation Engineers, Anaconda Copper Mining Co., Butte, Mont. San Francisco Meeting, February 1949. TP 2705 A. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received Jan. 17, 1949. Permissible Limits: The question of permissible dust limits has been considered by medical commit-ties and various national conferences. Dr. Lanza, of the Metropolitan Life Insurance Company, Dr. Le-roy U. Gardner, of the Saranac Laboratory for the study of Tuberculosis, and Dr. Pancoast, of the University of Pennsylvania, have been members of these committees. A statement included in reports of some of these committees is as follows: Concentrations to which the dust must be induced in order to be safe have not been absolutely determined. There is evidence that a concentration of more than five million particles per cubic foot of a highly siliceous dust is dangerous. Therefore, it may be stated that it is desirable to avoid counts of more than five million particles of dust containing free silica to a high percent in working places. Table I gives the safe limits adopted by several state industrial codes. Table I. Safe Limits of Dust Concentration Limit Million Particles State Per Cu Ft Cal~fornia Silica (less rhdn 10 pct) 50 Silica (10 pct to 50 pcr) 10 Sllica (more than 50 pct) 5 New York Frcc silica less than 10 pet by weight of rock formation 100 Frec silica more than 10 Pct by weight of rock formation 10 Oregon Silica (over 40 pct) 5 Silica (20 to 40 pct) 10 Silica (10 to 20 pet) 20 Wisconsin 15 million particles, under 10 nicrons in longest dimension per cu ft of air, when the quartz content of the dust is 35 pct, variations in free silica content will make proportional inverse changer in this standard Close attention to dust concentrations has been given to mining operations, since these operations are frequently carried on at considerable distances

Jan 1, 1951

By Albert F. J. Bordeaux

(Cleveland Meeting, October, 1912.) THE immediate vicinity of the sea-shore, affording special facility for the exportation of ores, makes it possible to work certain mines in the Vladivostok district, which, in more remote places of Siberia, would remain unproductive. Outside of the city of Vladivostok the population is small and the country is very little prospected. Additional discoveries of valuable deposits like the large body of calamine which has recently been opened in the neighborhood of earlier worked lead-silver ores, in the Tetiuhe valley, are still in the field of possibilities. For many years gold alone was produced, in part from the coastal rivers and in part from a quartz-vein on Askold island near Vladivostok. But the production is diminishing, and prospectors are looking for other rivers in the interior, such as the tributaries of the Ussuri. These rivers are now more accessible than formerly, due to the slow but gradual development, of colonization by the Russian peasants. The few natives of the country, called Orodjones, are of the Chinese race. They resemble the North American Indian and are hardy fur-hunters. They have given some attention to placers and have already shown good specimens of gold-dust from the rivers Iman, Bikin, Noto, etc. Coal-mining was begun in the Vladivostok region more than 20 years ago, but in a somewhat irregular way. The industry is not as yet important and the best coal-seams are badly prospected, or ire even neglected. Copper, lead, and iron exist in several places. The amounts give some encouragement to the anticipation that the discoveries will give rise to important metallurgical works. I here present a review of the various deposits, based upon such safe information as is in hand, when I have not drawn upon my personal observations. Fig. 1 is a snap of Eastern Siberia, showing the mineral deposits.

Oct 1, 1912

By AIME AIME

THE week, of April 5 will long be remembered by those that attended the Birmingham meetings of the Open-Hearth and Blast Furnace committees of the A.I.M.E. Iron and Steel Division. Birmingham iron and steel own received the 450 delegates with open arms; described and discussed their southern metallurgical practices and problems and compared experiences with their northern brother metallurgists in two days of technical sessions on Wednes-

Jan 1, 1937

By R. W. Raymond

It is impracticable to prepare for the present number of the Bi-Monthly Bulletin a detailed account of the memorable Joint Meeting of the Iron and Steel Institute and our Institute, held in London, the last week in July, and of the, innumerable festivities, entertainments and excursions which accompanied and followed it, in England, Scotland, Wales and Germany. This preliminary sketch, from which all " useful particulars "' have been carefully omitted, is published unofficially, as a convenient answer to the manifold inquiries of members who did not go, and who are now trying to alleviate their unavailing regret by indulging their curiosity. Perhaps they secretly hope to hear that they did not lose so very much, after all-that the affair was not all that could have been desired or dreamed; that there were serious drawbacks, shortcomings and disappointments; and that it is just as well to have stayed it home, and now to hear about it. Let them lay no such flattering unction to their souls. The month they have missed would have been the time of their lives. They will never, never know how good a time it was, or adequately repent of their folly, if they could have gone with us, and voluntarily did not go of course, those who would but could not, have our immeasurable pity, without blame. I shall present here no consecutive and minute story, but only a series of general paragraphs concerning different aspects and stages of our experience. THE WEATHER. The proverbial good fortune of the Institute attended its visiting members and guests at every stage of the late London meeting and the numerous excursions which accompanied or followed it. Even the process of crossing the Atlantic was made delightful by smooth seas, through which the great modern transatlantic liners made their way without disagreeable

Sep 1, 1906

By AIME AIME

SILVER reached a new high, with the ceiling the limit, at the annual Institute dinner at the Commodore on Washington's Birthday night. Carrying along as ballast other commodities, such as rolls, roses and ferns, souvenir boxes and table number placards, hundreds of silvery balloons, cut loose from their moorings at the tables, bounced idly against the plaster decorations high overhead. At the head table, Scott Turner, retiring President, pre- sided as toastmaster, with the new President, Frederick M. Becket, on his right, and the Chairman of the New York Section, Sydney H. Ball, on his left. Many other distinguished Institute members, medalists, and representatives of organizations and committees, ranged to the east and west. Each had the opportunity at least to rise and bow.

Jan 1, 1933

By Walter E. Mingramm

The construction of rescue-apparatus on the principle of furnishing the wearer with air from a tank containing it under high pressure was given up by inventors about 20 years ago. Such an apparatus must supply continuously, for not less than two hours, nearly 50 liters of pure air at atmospheric pressure per minute, or a total of 6,000 liters (210 cu. ft.); and a cylinder containing this amount of air, under 2,000 lb. pressure, would weigh 180 lb. or more. Although apparatus has been recently constructed utilizing liquefied air, no experiments have been made to determine the regularity with which the air is generated, nor has its chemical composition been determined. Moreover, the chief objection to such an apparatus is the difficulty and cost of keeping on hand a large quantity of liquefied air. The system of furnishing the wearer of a breathing-apparatus with air which has given the best results, and has found

Jan 1, 1909

By AIME AIME

WHETHER by the Mohawk Trail, Sound steamer, air plane, railroad or any other route or mode of locomotion, all roads will lead to Boston the week of National Metal Congress, Sept. 21-25. The Institute of Metals and Iron and Steel divisions of the Institute are then to meet jointly at the Hotel Statler, and the American Society for Steel Treating, the American Welding Society, the Society of Automotive Engineers and the Iron and Steel Division of the American Society of Mechanical Engineers present carefully planned programs at their respective sessions. The National Metal Exposition will be held on Commonwealth Pier.

Jan 1, 1931

By R. R. Joseph, K. A. Gschneidner

The solid solubility of magnesium in the close-packed modifications of lanthanum, cerium, praseodymium, neodymium, gadolinium, dysprosium, and lutetium was determined from approximately 250°C to the eutectoid temperature by the X-ray parametric technique. The maximum solubility at the eutectoid temperature was found to be 9.4 at. pet in La, 8.2 in Ce, 9.2 in Pr, 8.2 in Nd, 14.1 in Gd, 13.5 in Dy, and 11.5 in Lu. The solubility when compared at a homologous temperature was found to increase in a smooth manner with decreasing size factor from lanthanum to lutetium. It was found that the apparent atomic radius of magnesium when dissolved in the lanthanide solvent was constant and could be accounted for by consideration of several models dealing with departures from Vegard's law. The eutectoid temperatures for the lanthanide-rich La-Mg, Ce-Mg, and Nd-Mg systems were found to be 544", 505°, and 551°c, respectively. A study of the solid solubility of magnesium in the lanthanide metals was initiated because the valency and electron egativity difference are essentially constant and favorable for solid-solution formation, and thus one could examine the effect of size on terminal solid solutions. The size factors based on metal radii range from 14.6 pet for lanthanum to 7.5 pet for lutetium. Since the electronegativity difference is small, 0.06 unit or less, application of the Hume-~othery' and Darken and Gurry2 criteria for solid-solution formation indicates that the solubility of magnesium would be expected to be small for lanthanum (between 5 and 10 at. pet) and to increase as we proceed along the lanthanide series. A search of the literature revealed no data on the solubility of magnesium in the lanthanide metals except for the solubility of magnesium in cerium at 450oCA typical phase diagram for the lanthanide-rich end of the lanthanide-magnesium phase diagram is shown in Fig. 1. EXPERIMENTAL PROCEDURES Preparation of Alloys. The lanthanide metals used in the preparation of alloys for this investigation were prepared from the corresponding fluoride by metallothermic reduction techniques previously described by Daane.4 The chemical analyses of the metals used are listed in Table I.

Jan 1, 1965

By Richard A. Mullins, James J. Merle

Systematic sampling and analysis in coal-washing plants results in product control and economical operation. A well-organized laboratory system reduces operating costs and increases sales if the operating and sales companies make full use of information it supplies. The operating cost of a control laboratory is less than 1 pct per ton of coal produced. THE system of laboratory control as practiced by the Ayrshire group of mines was begun with the construction and organization of the first laboratory in conjunction with the completion of its first wash-ery in 1941. The primary purpose of this laboratory was to maintain a check on the quality of the coal produced from the washing plant. The laboratory was equipped to determine proximate analyses, float-and-sink tests, and screen analyses, and was staffed by a chemist. an assistant. and a technician. Members AIME, are Assistant Preparation Manager and Chief Chemist, respectively, Ayrshire Collieries Corp. and Subsidiaries, Danville, Ill. Joint AIME-ASME Fuels Conference. French Lick. October 1949. TP 2855 F. Discussion (2 copies) may be sent to Transactions AIME before June 30, 1950. Manuscript received Aug. 22, 1949. Soon it became apparent (1) that product control could be accomplished, (2) that a substantial reduction in operating costs could be effected by close control of coal losses in the rejects, and (3) that information furnished by the laboratory was of continuous value to the operating and sales companies. Consequently the laboratory function was expanded to supply them with additional data as required. As the parent company expanded and new mines were added, control laboratories were established at each mine equipped with washeries, and a central laboratory was maintained at one of the mines that was located equally convenient to all of them. A well-planned control laboratory assures production of a uniform, high-quality product. Whenever coal of substandard grade is loaded inadvertently, the sales company can be informed and the proper channel of distribution made. Conversely only constant and strict laboratory supervision can insure proper production of the various grades. Knowing the product, the producer can keep out of many customers' arguments that may be both awkward and expensive. Double checking between customers and mine laboratories have solved many disputes' Some nager insist On buying coal On the analysis basis only, with penalties for substandard coal and premiums for coal above normal quality. A substantial percentage of the coal sold by the Ayrshire group is of this nature. The usual procedure is for the customer to sample and analyze the coal as it is unloaded at the plant, and the mine laboratory samples it as it is loaded at the mine for subsequent analysis by the central laboratory. Only the unloaded moisture is considered, rather than the average of mine and plant moisture, and the buyer sends duplicate samples to the central mine laboratory for this determination. The average of the two analyses determines the price of coal at the mine. In this particular case, the laboratory plays an important part in increasing realization for two reasons: (1) every attempt is made to maintain plant efficiency and product quality as high as possible, (2) check on analyses and sampling by the buyer or seller.

Jan 1, 1951

By Richard A. Mullins, James J. Merle

Systematic sampling and analysis in coal-washing plants results in product control and economical operation. A well-organized laboratory system reduces operating costs and increases sales if the operating and sales companies make full use of information it supplies. The operating cost of a control laboratory is less than 1 pct per ton of coal produced. THE system of laboratory control as practiced by the Ayrshire group of mines was begun with the construction and organization of the first laboratory in conjunction with the completion of its first wash-ery in 1941. The primary purpose of this laboratory was to maintain a check on the quality of the coal produced from the washing plant. The laboratory was equipped to determine proximate analyses, float-and-sink tests, and screen analyses, and was staffed by a chemist. an assistant. and a technician. Members AIME, are Assistant Preparation Manager and Chief Chemist, respectively, Ayrshire Collieries Corp. and Subsidiaries, Danville, Ill. Joint AIME-ASME Fuels Conference. French Lick. October 1949. TP 2855 F. Discussion (2 copies) may be sent to Transactions AIME before June 30, 1950. Manuscript received Aug. 22, 1949. Soon it became apparent (1) that product control could be accomplished, (2) that a substantial reduction in operating costs could be effected by close control of coal losses in the rejects, and (3) that information furnished by the laboratory was of continuous value to the operating and sales companies. Consequently the laboratory function was expanded to supply them with additional data as required. As the parent company expanded and new mines were added, control laboratories were established at each mine equipped with washeries, and a central laboratory was maintained at one of the mines that was located equally convenient to all of them. A well-planned control laboratory assures production of a uniform, high-quality product. Whenever coal of substandard grade is loaded inadvertently, the sales company can be informed and the proper channel of distribution made. Conversely only constant and strict laboratory supervision can insure proper production of the various grades. Knowing the product, the producer can keep out of many customers' arguments that may be both awkward and expensive. Double checking between customers and mine laboratories have solved many disputes' Some nager insist On buying coal On the analysis basis only, with penalties for substandard coal and premiums for coal above normal quality. A substantial percentage of the coal sold by the Ayrshire group is of this nature. The usual procedure is for the customer to sample and analyze the coal as it is unloaded at the plant, and the mine laboratory samples it as it is loaded at the mine for subsequent analysis by the central laboratory. Only the unloaded moisture is considered, rather than the average of mine and plant moisture, and the buyer sends duplicate samples to the central mine laboratory for this determination. The average of the two analyses determines the price of coal at the mine. In this particular case, the laboratory plays an important part in increasing realization for two reasons: (1) every attempt is made to maintain plant efficiency and product quality as high as possible, (2) check on analyses and sampling by the buyer or seller.

Jan 1, 1951

By William Marsh Baldwin

TWO of the most useful and important equations available to the metallurgist for the study of plastic deformation of metals are the Huber-von Mises-Henckyl-~ and the St. Venant7-10 equations. Huber-von Mises-Hengky Equation The Huber-von Mises-Hencky equation answers the question: When does plastic flow occur in metal that is subjected to a multi-axial stress? It occurs, according to this equation, when the three principal stresses,t UI, u2, and u3 satisfy the equation: (<ri - <r2)2 + (<r2 - <rsY + (ff! - <r3)* = 2Ki [i] Here K is the yield strength of the material as determined in an ordinary tensile test. If the quantities ul, 52, andas are assigned to the coordinates of a Cartesian three-dimensional system, this expression describes a cylinder whose axis of symmetry is inclined at equal angles to the three coordinate axes4s6 (Fig. I). The radius of this cylinder is .\/%K. For the purpose of simplicity, it is sometimes advantageous to ascribe the values al/K = sl, az/K = s2, UD/K = SJ to the three coordinate axes instead of the principal stress alone. In this case, Eq. I becomes (*i - s*)1 + (s2 - S3)2 + (si - SiY = 2 [2] and the radius of the cylinder becomes \/%. In the latter method of representation, a point lying inside the cylinder indicates that the metal will react elasti-cally, whereas a point lying on the cylindrical surface indicates that the metal will behave plastically. Some of the geometric features of this cylinder are worthy of study. Let us inquire first as to what interpretation may be placed upon what we will choose to call the "circles of latitude" of the cylinder (L in Fig. I) and the "meridians" of the cylinder (M in Fig. I). Circles of Latitude Circles of latitude are formed by allowing a plane, passing perpendicular to the cylinder axis, to intersect with the cylinder. Any point, P, on this circle is presumed to have the coordinates sl, SZ, and s3. The coordinates of the point resulting from the intersection of the plane and the cylinder axis will be a, a, and a (since the cylinder axis is equally inclined to the three coordinate axes). L?t US now pass a line through the point on the circle and the point on the axis.

Jan 1, 1946

By William Marsh Baldwin

TWO of the most useful and important equations available to the metallurgist for the study of plastic deformation of metals are the Huber-von Mises-Henckyl-~ and the St. Venant7-10 equations. Huber-von Mises-Hengky Equation The Huber-von Mises-Hencky equation answers the question: When does plastic flow occur in metal that is subjected to a multi-axial stress? It occurs, according to this equation, when the three principal stresses,t UI, u2, and u3 satisfy the equation: (<ri - <r2)2 + (<r2 - <rsY + (ff! - <r3)* = 2Ki [i] Here K is the yield strength of the material as determined in an ordinary tensile test. If the quantities ul, 52, andas are assigned to the coordinates of a Cartesian three-dimensional system, this expression describes a cylinder whose axis of symmetry is inclined at equal angles to the three coordinate axes4s6 (Fig. I). The radius of this cylinder is .\/%K. For the purpose of simplicity, it is sometimes advantageous to ascribe the values al/K = sl, az/K = s2, UD/K = SJ to the three coordinate axes instead of the principal stress alone. In this case, Eq. I becomes (*i - s*)1 + (s2 - S3)2 + (si - SiY = 2 [2] and the radius of the cylinder becomes \/%. In the latter method of representation, a point lying inside the cylinder indicates that the metal will react elasti-cally, whereas a point lying on the cylindrical surface indicates that the metal will behave plastically. Some of the geometric features of this cylinder are worthy of study. Let us inquire first as to what interpretation may be placed upon what we will choose to call the "circles of latitude" of the cylinder (L in Fig. I) and the "meridians" of the cylinder (M in Fig. I). Circles of Latitude Circles of latitude are formed by allowing a plane, passing perpendicular to the cylinder axis, to intersect with the cylinder. Any point, P, on this circle is presumed to have the coordinates sl, SZ, and s3. The coordinates of the point resulting from the intersection of the plane and the cylinder axis will be a, a, and a (since the cylinder axis is equally inclined to the three coordinate axes). L?t US now pass a line through the point on the circle and the point on the axis.

Jan 1, 1946

By A. Satter

Studies of wellbore heat transtnission during the injection of a hot fluid, as either gas or liquid, have appeared in he literature. The present investigation takes into account the effect of condensation, which is of practical sig-nificance when considering steam injection operations. Calculation procedures are given for superheated and for saturated and undersaturated steam. Effects of injection rate, time, pressure, temperature and depth of a well on heat losses have been analyzed. The benefits of using a packer are discussed. Also presented are correlations for estimating heat losses involved during injection of saturated steam. INTRODUCTION Studies of wellbore heat losses during the injection of a hot fluid have appeared in the literature. Ramey&apos; has presented a useful solution for calculating temperature of a heated gas as a function of depth and injection time. Ramey and others have also presented solutions for the hot liquid case.&apos;. &apos; No method is available to take into account the effect of condensation, which is of practical significance when considering steam injection operations. This paper presents a method of estimating the quality of a condensing fluid as a function of depth and time. The approach is basically the same as that used by Ramey. The following injected fluids and conditions are considered in this study: 1. Injection of superheated steam A. Decrease in temperature until cooled to the saturated state B. Condensation until condensed completely into hot (saturated) water 2. Injection of saturated or undersaturated steam; condensation until condensed completely into hot (saturated) water. Although this investigation does not include cooling of water after steam is completely condensed, Ramey&apos;s solution for the hot liquid case can be used for this purpose. The effects of various process variables on heat losses During the injection of steam into a well are investigated. THEORY QUALITY OF CONDENSING STEAM Predicting the behavior of condensing steam flowing down the injection wellbore requires an estimate of the quality of steam, i.e., the mass fraction of vapor in the mixture. Let us divide the total depth of the injection well into several segments which might be, but do not have to be, of equal magnitude. Consider condensation within a given depth interval AZ, the bottom of which is located at a depth Z from the surface (Fig 1). The following equation, derived in the Appendix- relates the quality of steam at the bottom of an interval to that at the top of the interval:

Jan 1, 1966

By Thomas B. Douglas

INSTRUMENTATION in the process industries can no longer be regarded as a convenience, but rather an absolute necessity. Although many chemical processes must already be conducted with instruments, every properly designed application of automatic process control will improve operation: 1) the product will be more uniform and of higher quality; 2) the manual labor saved will reduce cost; 3) uniformity of flow and uniform control of process will increase production; and 4) surges will be eliminated, making it possible to operate equipment near ultimate capacity at all times. Industrial instruments fall into two general classifications-those that measure and those that measure and control. The cement industry has been using instruments for a number of years, particularly in the burning process, primarily for indicating and recording. Automatic process control makes additional use of these instruments, and others, to control variables. Assisted by the instrument manufacturers, engineers at Ideal Cement CO. achieved considerable progress in determining how well the usual recording instruments could be made to control various phases of cement-making. The results of these experiments were used to make the new plant at Houston as wholly automatic as possible.

Jan 2, 1958

By W. H. Boyer, J. W. Gabelman

The concept of metal zoning has long been recognized (Spurr, 1907, 1923; Emmons, 1924, 1926; Lindgren, 1933; Rateman, 1950), although it has been considered indistinct for most epithermal districts. The geometric relation of barren zones of hydrother-mally altered rock to ore deposits was emphasized in the work of Lovering (1941, 1949, 1950), Sales and Meyer (1948, 1949, 19501, Burbank (1941, 1950), Schwartz (1939, 1950), and Kerr (1947). Lovering (op. cit.) and Sales and Meyer (op. cit.) emphasized the consistent presence of barren alteration envelopes enclosing individual ore bodies, particularly of the vein type. Schwartz (1950) noted a difference between the distribution of alteration zones described by Lovering and by Sales and Meyer, as compared with those associated with the porphyry copper deposits of the Southwest. The disseminated deposits of the Southwest usually occur within large bodies of altered rock whereas most veins do not. In the following discussion the mineralization process is conceived of consisting of two distinct phases: pre-ore nonmetallic alteration and metallization. In the present investigation the position, size, and shape of all known hydro thermally altered areas and the position, size, and metal type of all known ore deposits were plotted on base maps of southwestern and west-central Colorado (Figure 1). The maps indicate a generally consistent geometric relation between altered and metallized areas. The addition of alteration to the pattern of metal deposits establishes a temperature zoning pattern of much greater clarity than that formed by the epithermal metal deposits alone, and allows a more precise definition of mineral belts. The center of strongest mineralization is indicated to be the area of greatest barren alteration, and metal deposits are grouped about it both under structural control and crudely in response to temperature zoning. The combination of an area of strong alteration and associated marginal clusters of metal deposits is defined as a mineral district. The strong similarity in individual deposits, in groups of different types of deposits, and in the alteration-metallization relation in districts throughout the region implies that a single metallogenic province is represented in southwestern and west-central Colorado. The occurrence of deposits in Tertiary voi-canics indicates a late Tertiary metallogenic epoci., although an early Tertiary epoch is known locally as at Ouray. Patterns formed by mineral districts can be

Jan 1, 1961