Search Documents

By D. J. Weintritt, J. C. Cowan

Methods of studying oilfield mineral .scale deposition in the laboratory do not work for barium sulfate because only small nonadhering crystals ore formed. On the other hand, barium sulfate scale found in down-hole or surface equipment is strongly adhering and may contain very large crystals. Results suggest that most of the difference derives from the extremely low .solubility of barium sulfate. Firm adherence of scale and the consistent development of oriented crystals 100 microns and larger suggest a relationship between scale adherence and crysta1 growth. Data from this study indicate some reasons for barium sulfate's occurring as a deposit in oilfield waters. The unique characteristics as well as the associative properties of barium sulfate scale as related to calcium carbonate and calcium sulfate ere shown. INTRODUCTION The first observed deposition of barium sulfate scale in oilfield production equipment is unknown but probably coincides closely with the beginnings of the oil industry itself. Moore' described barite oolites in some producing wells in the Saratoga field, Tex., in 1914. Currently, positive identification of barium sulfate deposition is recorded in most of the major oil-producing areas of the United States. As efforts continue to identify the composition and functions of the materials found in scale deposits, the geographic and economic importance of the part played by barium sulfate will become even more important. This belief is based on the following Facts. 1. Many oil fields in the U.S. are in or entering their mature phase and the volume of produced water is increasing; thus, the cumulative effects of low-solubility minerals become more significant. 2. Secondary recovery techniques and increased emphasis on waste disposal systems require controlling the behavior of all constituents of water to prevent formation plugging. 3. The more general use of instrumental analysis has reduced the time and improved the accuracy of complete scale and water analysis. 4. Once formed, barium sulfate scale is resistant to present methods of chemical removal; therefore, costly mechanical methods are necessary. Thus, new methods of prevention and control will require specialized chemical techniques and better knowledge of the causes of scaling. Consider the results of some simulated field deposition studies illustrating this need (Fig. 1). The studies utilized a Scale Deposition Test Cell* and each coupon was exposed to 8,000 ml of a 300 me/liter solution of the various types of mineral scale. All tests were conducted at 140F. Only the calcium sulfate and calcium carbonate deposited scale. The solution containing 300 me/liter of barium sulfate exhibited copious amounts of precipitate, but none of the precipitate adhered. The fluids from the effluents were also allowed to impinge on glass slides. Fig. 1 shows the relative adherence of the three types of scale on unetched glass. The barium sulfate failed to deposit in the same manner as the calcium carbonate and calcium sulfate solutions.

By Reynold Q. Shotts

INTRODUCTION THE small domestic underfeed stoker as now designed is unusually sensitive to the coking and plastic properties of coals, and when the attempt is made to burn the high rank coking and caking coals of the Appalachian fields, serious trouble may occur. Part of the trouble may be caused by the ash content and clinkering characteristics of the particular coal in use, but more often it is the result of an excessive accumulation of coke in the form of "trees" or masses in the fuel bed. Often the zone of burning becomes so restricted that the fire goes out, and in extreme cases the fire may be lifted completely out of the fuel bed and away from the air ports. Even if the fire is preserved, excessive coking may cause response to subsequent heat demand to be slow and irregular. Coke trees seem to grow. most readily during periods of hold-fire operation, so that in order to preserve the fire in mild weather it is often necessary to set the timer for such a long operating period each hour that much unneeded and unwanted heat is developed, causing discomfort. During demand periods the fire may pick up so slowly that the intense burning which develops just before stoker cut-off causes a serious overshooting of the thermostat. Stoker coal performance tests which have been made in a number of laboratories 1, 2, 3, 4, 5 are one method of approach to the problem of selecting stoker coals. As yet these tests have not been standardized and they are expensive and time-consuming. The value of the results probably increases with the length of the test. Sherman and co-workers at Battelle Memorial Institute believe that even a one-week test is not too reliable a trial2 and it is quite likely that others will agree. A great advantage of such tests is that characteristics of coals, other than the tendency to form coke masses, may be evaluated from them. The selection of stoker coals would be greatly facilitated if there existed some simple measure of the tendency of a coal to form coke in a fuel bed. Although possessing all of the disadvantages of any small-scale laboratory test, the test for the free-swelling index of coal has been found useful for evaluating the probable effects of swelling properties upon combustion. 7 Ostborg, Limbacher and Sherman, have shown that the test can predict, roughly, the tendency of coke to accumulate in the fuel bed of a domestic stoker. They also gave instances of its value in predicting combustion behavior in some large installations. The use of the test for free-swelling index has become well established and has been adopted as a standard by the American Society for Testing Materials.8 When domestic stoker coal investigations began at the State Mine Experiment Station in the summer of 1944, it was decided

Jan 1, 1948

By James W. Shaffer

Aluminum is the most abundant metallic element and forms 8% of the earth's crust. Because of its chemical activity it does not occur in nature in a metallic form but principally in the silicates, feldspar, mica, shale, and clay. Bauxitic raw materials-bauxitic clay, aluminous laterite, and bauxite-develop from these aluminum silicate sources. Bauxite and aluminous laterite are naturally occurring mixtures of aluminum hydroxides and mineral impurities, and they are the major sources of aluminum. End Uses Bauxite is the basic ore of the aluminum industry. It is refined into aluminum hydroxide and calcined for feed stock to electrolytic smelters. Over 90% of the tonnage mined is refined and smelted into aluminum. The total tonnage consumed by other industries is small in comparison, but bauxite and alumina are important for the manufacture of refractories, ceramics, chemicals, abrasives, pharmaceuticals, catalysts, cements, dessicants, and flame retardants. Some aluminum-containing industrial products are made from clays and other materials but the majority originate from bauxite directly or from aluminum hydroxide and alumina refined from bauxite. Lateritic type bauxite is also used as building and decorative stone. Geology Mineralogy and Properties Bauxite is a mineral raw material composed principally of one or more aluminum hydroxide minerals and impurities of silica, iron oxide, titania, and other elements in minor or trace amounts. The important aluminum hydroxide minerals are gibbsite, boehmite, and diaspore. Bayerite, nordstrandite, and tucanite are naturally occurring aluminum hydroxides but are rare and not commercially important. Mixtures of gibbsite and boehmite are common, boehmite and diaspore less common, and gibbsite and diaspore rare. Gibbsite is aluminum trihydroxide. Boehmite and diaspore are aluminum oxide hydroxides and have essentially the same composition, but diaspore has a greater hardness and a more tightly bonded and denser atomic structure. Although not technically correct, the commercial terms trihydrate and monohydrate are frequently used to distinguish types of bauxite. If bauxite is all or nearly all gibbsite, it is referred to as a trihydrate ore; if boehmite or diaspore or a mixture of both are the dominant minerals, the bauxite is called a monohydrate ore. If substantial amounts of both gibbsite and boehmite are present, the bauxite is frequently referred to as a mixed ore. Properties of major bauxite minerals are shown in Table 1. Silica, iron oxides, and titania are major impurities always present in deposits of bauxitic raw materials.. Silica impurities usually occur as clay minerals, micaceous minerals, or quartz, but cristobalite and feldspar are found in some deposits. The most common clay minerals are kaolins; however, illites and chlorites are often found in small quantities. Varying proportions of aluminum, iron, and clay minerals make bauxite, aluminous laterite, ferruginous laterite, and bauxitic clay deposits gradational with each other. Hematite and goethite are the common iron mineral impurities in many bauxites. Magnetite and ilmenite occur in deposits derived from basic igneous rocks. Other iron minerals associated with bauxite are maghemite, pyrite, siderite, and marcasite. The titanium minerals found in bauxites are anatase, leucoxene, rutile, ilmenite, titaniferous

Jan 1, 1983

By Alfred V. de Forest

We are now assembled in this hall for the eighteenth lecture in honor of the memory of our greatest American metallurgist, Henry Marion Howe. Many of his most intimate contemporaries, led, as was fitting, by Professor Sauveur, have described his vital accomplishments in three fields: as a leader in technical industrial development; in theoretical research; and finally as a teacher and source of inspiration for nearly two generations of students. In 1914 Professor Howe had retired from active teaching, but maintained his laboratory at Columbia University under the care of Arthur G. Levy, with whom he published many of the papers that later were incorporated into his last book, " The Metallography of Steel and Cast Iron." My position at the time was that of personal assistant to Professor Campbell—no pay, no duties, but the great privilege of preparing specimens, taking pictures and attending to some of the current consulting work. Whenever possible, I visited Howe's laboratory to chat with Levy and gather ideas about the wonderful field of metallography—in which I was a rank amateur, rescued by the quiet enthusiasm of Donald Smith of Princeton from an instructorship in civil engineering. Levy let me act as a fly on the wall during the Professor's occasional visits. Busy as he was, Professor Howe took the time and trouble to encourage my interest, as he had done for hun- dreds of others. He told me how he went about gathering his own information speculating as to causes, considering experiments, and verifying his conclusions. I ventured to mention some tests I had run on the irregular stretching of wires of different metals. He read the small volume I had prepared of ill-assorted facts and fancies and remarked: "Nobody cares for your theories or the history of your tests. Describe what you found as briefly as possible and perhaps I can help you to publish." Curiously enough, among my discards were some autographically recorded load-versus-electrical-resistance measurements. Taken with inadequate knowledge and equipment, these curves did not reproduce consistently, but if the relationship between strain and resistance had then been explored, the latest type of strain gauge might have been in useful service for the past 25 years. Professor Howe was a gifted teacher, perhaps because he was primarily an ardent and assiduous student. His own eagerness to learn and his willingness to revise and extend his opinions constantly encouraged those of his environment to be diligent and painstaking in the pursuit of knowledge. In honoring his memory, I also wish to bring to mind the kindly, humorous and quiet Levy, and join his name again, as it was for too brief a space in the past, with that of many-sided Henry Marion Howe. Factors oF Impact Strength The subject chosen for the Howe Memorial Lecture by Dr. Gillett last year

Jan 1, 1941

By Alfred V. de Forest

We are now assembled in this hall for the eighteenth lecture in honor of the memory of our greatest American metallurgist, Henry Marion Howe. Many of his most intimate contemporaries, led, as was fitting, by Professor Sauveur, have described his vital accomplishments in three fields: as a leader in technical industrial development; in theoretical research; and finally as a teacher and source of inspiration for nearly two generations of students. In 1914 Professor Howe had retired from active teaching, but maintained his laboratory at Columbia University under the care of Arthur G. Levy, with whom he published many of the papers that later were incorporated into his last book, " The Metallography of Steel and Cast Iron." My position at the time was that of personal assistant to Professor Campbell—no pay, no duties, but the great privilege of preparing specimens, taking pictures and attending to some of the current consulting work. Whenever possible, I visited Howe's laboratory to chat with Levy and gather ideas about the wonderful field of metallography—in which I was a rank amateur, rescued by the quiet enthusiasm of Donald Smith of Princeton from an instructorship in civil engineering. Levy let me act as a fly on the wall during the Professor's occasional visits. Busy as he was, Professor Howe took the time and trouble to encourage my interest, as he had done for hun- dreds of others. He told me how he went about gathering his own information speculating as to causes, considering experiments, and verifying his conclusions. I ventured to mention some tests I had run on the irregular stretching of wires of different metals. He read the small volume I had prepared of ill-assorted facts and fancies and remarked: "Nobody cares for your theories or the history of your tests. Describe what you found as briefly as possible and perhaps I can help you to publish." Curiously enough, among my discards were some autographically recorded load-versus-electrical-resistance measurements. Taken with inadequate knowledge and equipment, these curves did not reproduce consistently, but if the relationship between strain and resistance had then been explored, the latest type of strain gauge might have been in useful service for the past 25 years. Professor Howe was a gifted teacher, perhaps because he was primarily an ardent and assiduous student. His own eagerness to learn and his willingness to revise and extend his opinions constantly encouraged those of his environment to be diligent and painstaking in the pursuit of knowledge. In honoring his memory, I also wish to bring to mind the kindly, humorous and quiet Levy, and join his name again, as it was for too brief a space in the past, with that of many-sided Henry Marion Howe. Factors oF Impact Strength The subject chosen for the Howe Memorial Lecture by Dr. Gillett last year

Jan 1, 1941

By C. S. Barrett, D. B. Masson

Martensitic transformations have been found in AgCd both upon cold-working at room temperature and cooling to lower temperatures. The crystal structures of the transformation products were found to be close-packed hexagonal in the first case and or-thorhombic in the latter. The transformation characteristics also were studied. Similar treatment of AuZn alloys failed to yield any transformation. THE literature on martensitic transformations of body-centered cubic metals and alloys indicates widespread instability of this structure at low temperatures, a tendency which merits further study. The body-centered cubic ß-phase of CuZn, for example, when it contained less than 42 wt pct Zn, was found by Greninger and Mooradian' and others' to transform on cooling to subzero temperatures to a phase that was tentatively considered to be tetragonal. Further work by Massalski and Barrett" demonstrated that cold work at low temperatures causes a partial transformation of ß CuZn of higher Zn content. The structures of the strain-induced transformation products were found to be different from those induced by simple cooling. Another well-known martensitic transformation among body-centered cubic phases is that of ß AuCd, first studied with X-rays by Olander,' then very thoroughly by Chang and Read.5,6 Here again transformation was found to occur both as a result of cooling and of strain. The alkali metals Li and Na, as well as certain Li-Mg alloys, also undergo transformation from their normal body-centered cubic structure, both on cooling and on cold-working. The phase AgCd, the subject of the present report, should be expected to behave quite similarly to CuZn for a number of reasons. It is the chemical analogue of CuZn, silver being directly below copper and cadmium directly below zinc in the periodic table. The size factors (percent difference in size) of the atoms, possibly a consideration in the stability of the ß-phases, are +3.1 in AgCd and + 4.2 in CuZn. Likewise the relative electronegativities of the two pairs of metals are about the same, CuZn possessing an electronegativity difference of 1.0 and AgCd one of 0.8. These values are from a table of electronegativities given by Darken and Gurry." The phase diagrams of the two systems around 50 atomic percent are similar, both possessing a disordered body-centered cubic phase, ß, at high temperatures and an ordered bcc phase, ß, at room temperature; however, the ß and ß' phases of AgCd are separated by a hexagonal phase, [, stable in the range 220-440oC, which has no analogue in CuZn. There has been confusion in the literature as to the structures of the ß' and [-phases. The phase diagram in the ASM handbook'" has the structures of the two phases interchanged; however, Hansen" reports the correct relative positions and Muldawer" verified that ß', the low-temperature phase, is body-centered cubic. Work by the present authors also

Jan 1, 1959

By Claus G. Goetzel

SOME of the reactions and procedures upon which modern techniques in the production of metal powders are based were used for 2000 years by the ancients to reduce iron and other metals from their ores. Despite this, however, the art of powder metallurgy is relatively new and probably stems from the introduction of incandescent electric lamp filaments. Attempts to improve upon Edison's carbon filaments led to the production, in order. of metallic filaments of osmium. tantalum.. and finally of tungsten, which ha, replaced the others and is the commercial product of today. These metallic filaments were originally manufactured by the extrusion and sintering of a mixture of the metal or its oxide with a reducing agent which also served as a binder. Further progress in this direction was in the pressing of a small percentage of nickel with the tungsten. The sintering operation was carried out in an atmosphere of hydrogen, at a tem-

Jan 1, 1944

By David E. Hyatt

The chemical attributes of cyanides have long been exploited in ore pro- cessing schemes for the recovery of copper, molybdenum, gold, silver, and other metal values. Blast furnacing operations are significant unintentional producers of cyanides which find their way into process waters. Many of the more than 20,000 electroplating facilities in the United States utilize cyanide plating baths and generate cyanide containing wastes. As social, political, and economic pressures for water quality attainment, maintenance, and preservation grow, the requirements for the development of treatment technology to control cyanide levels in wastewater become increasingly apparent. Just as the chemistry of the cyanide ion 1s an integral part of its industrial applicability, so must this chemistry be a fundamental part of any decomposition or removal technology used to control its level in effluent or recycled waters. The complexity of this chemistry is substantial and it cannot be considered in a superficial or cursory manner if control system design is to be both efficient and reliable.

Jan 1, 1975

By William Romanoff

IN AN ARTICLE on "Recovering Smelter Dust and Oxide," published in the Engineering and Mining Journal (Vol. 131, No. 2), the authors briefly described some dust-recovery equipment and its operation at a secondary-metals brass-smelting and refining plant. A description of our experience in overcoming certain operating difficulties may prove of interest or value to those who are confronted with some of the same problems or who should equip their furnaces with dust-collecting equipment. The dust loss from reverberatory smelting and refining of brass con¬sists largely of zinc, with smaller percentages of lead, tin, and copper in the order named. At the Kramer plant, the fume discharge from the two stacks amounted to 3 to 4 tons of solids per day, making a dense smoke. With dust equipment in operation, the discharge from the stacks is invisible and approximately 2500 lb. of zinc and other metals is recovered daily thereby from each furnace operating.

Jan 1, 1933

By Oscar A. Glaeser

MINE VENTILATION is an important factor in mine maintenance as well as having direct bearing on labor efficiency. Effective ventilation systems are costly, especially those for the deeper mines, but with intelligent direction the worth of a system is usually greater than its cost. In most mines using mechanical ventilation, and practically all deep mines, it has been found beneficial to equipment, timber, and the ground, to run the fan or fans continuously even though production has been curtailed or entirely suspended. Therefore, economies in ventilation may be overlooked when general cost reductions are necessary. The operating costs of a well-designed ventilation system should be capable of reduction during periods of curtailed or suspended operations. A mine that is ventilated by splits, or that can be sectionized, can reduce its fan-power costs considerably, and provisional divisions can sometimes be made in other mines, in which the air is ordinarily coursed through all the workings, without harmful effects.

Jan 1, 1932

By Hermsdorf, Richard P. E.

AMONG the newer lead smelting and refining plants of the country is that of the United States Metals Refining Co., at Carteret, N. J. Not only is the technical practice here modern and efficient, but exceptional care is taken to assure healthful operating conditions for the employees. One large building houses the entire department, which includes, as its chief units, one reverberatory smelting furnace, one blast furnace, two softening furnaces, one utility reverberatory furnace, two Faber du Faur retorts, five 120-ton kettles, three 60-ton antimouial lead kettles, and one 5-ton kettle for experimental purposes. There is a 10-ton overhead crane in the kettle aisle, which is also used for shipping lead. Other auxiliary equipment is referred to in the outline of operations. A general plan of the plant is shown in Fig. 2, and a general view in Fig. 1. Primary smelting operations are conducted in a 30 by 11-ft. reverberatory furnace with bottom, roof, and upper walls of clay brick, magnesite

Jan 1, 1934

By Allan J. Clark

THE September issue of MINING AND METALLURGY might almost have served as a review of the advances in the metallurgy of gold during the current year. In addition to a scholarly article by F. W. Bradley, there were able descriptions by W. W. Bradley and W. F. Boericke of the methods followed in California and in Ontario. Considered together, the two last-named articles indicate the many possible combinations of flotation with one or more of the older processes. This, the prominence of flotation as an aid in the beneficiation of gold ores, is probably the most striking of the year's developments. It would perhaps be nearer the fact to say that the year has not been marked by the gold metallurgists' discovery of the flotation process, but rather by the flotation merchandizers' discovery of gold metallurgy. I say this because native gold was floated successfully more than fifteen years ago, and a reference to these results was published six years ago.

Jan 1, 1933

By AIME AIME

A CORPORATION would go into bankruptcy if its affairs were conducted as are those of the state of New York, according to the Committee on New York State Government Reorganization of the American Engineering Council of the Federated American Engineering Societies, in a report to the chairman, of the Joint Judiciary Committees of the Senate and Assembly. The report, just made public, was signed by the three members of the committee who were appointed by Herbert Hoover. They were H. de-B. Parsons, chair- man, Paul G. Brown and Lewis B. Stillwell. Although the American Engineering Council is a national organization, it decided to aid in governmental reorganization in New York State because of the magnitude of the task. The Council's committee in its report urged the passage of three state reorganization amendments for consolidation of departments, an executive budget system, and a four-year term for the higher state officials. In the words of the report :

Jan 1, 1921

By Carel Robinson

THE little coal mine at Otsego, in the Winding Gulf field of southern West Virginia was dying. In the history of coal mining thousands of mines have been successful at first, but usually a change occurred and profits ceased. Often be change was so gradual and extended over such a length of time that the fundamental causes did not stand out in sharp relief and their significance was not realized. Studies often reveal that the cause for failure was in the arteries that connect the producing places with the mine entrance. Profits continued so long as the working places were close to the tipple and while the thrill of newness aid ease of access resulted in effective supervision from day to day. The air- way and haulageway, the wire line and manway, may have been sufficient when the distance from the entrance was a few hundred feet, but were inadequate when this was extended for thousands of feet.

Jan 1, 1937

By Simon D. Strauss

The world appetite for minerals in the, third quarter of this century grew at a higher rate than had been anticipated. To illustrate, consider the experience of four, commodities. Excluding the Communist bloc, sometimes referred to as the centrally planned economies, demand for aluminum increased at a compound rate of 8.6% between 1950 and 1975,; copper rose by 4.4%; iron ore by 5.5%; and tin, the laggard in the group, by 2%. Except for tin, the figures are substantially greater than growth rates anticipated in 1950 in the Paley Commission report and other studies. The growth rate was not evenly distributed in geographical areas. Professor Wilfred Malenbaum of the University of Pennsylvania did an interesting study breaking these figures down as among three principal sources of demand -- the United States, other industrialized nations (which he referred to as the "rich lands"), and the developing world (which he referred to as the "poor lands").

Jan 1, 1982

By A. L. Bailey, B. A. Landry

W. W. ANDERSON and G. E. KELLER*—We want to compliment the authors on this very thorough paper. It gives information which the coal industry has needed for some time. We hope that the additional information which the authors are collecting will he available shortly. The mixing and riffling procedure that was followed for experimental purposes is obviously not practical in routine float-and-sink testing because of the particle size degradation which would result in handling the sample so many times. It is important to obtain our tloat-and-sink fractions with a minimum amount of handling of material. A statement is made in the paper (p. 80) that "the variable most likely to affect the size of sample required to meet a given preassigned accuracy would be the state or degree of mixing of the coal." We agree that this is a large factor, but do not believe it is the most important factor. Our own opinion is that the most important single factor governing the total gross weight of sample that must be collected is the percentage of the weight of material in the smallest fraction that results from the screening and float-and-\ink operations. In other words, size of sample is governed by the total number of fractionations that must he made, and the distribution of material within the fractions. We can imagine a coal with perfect mixing, but with such a small amount of material in some float-and-sink fraction in one of the coarse sizes that a much larger sample would have to be taken than would be the case with very poorly mixed material, but with a large percentage of coarse material more evenly distributed in all float-and-sink fractions. Our own observation of many float-and-sink tests that we have run in our own organization on many types of coal is that the size of sample that must be used on fine size float and sink is governed more by the requirements for weight of material to be used for analysis in the laboratory than by weight of material necessary to obtain accurate float and sink percentage of weight values. In other words, it is our opinion that very small samples can be used for float-and-sink fractionation in the fine sizes, but that accurate analysis of the fractions will depend on a larger weight of sample being pulverized for the laboratory than is necessary to establish the float-and-sink distribution with respect to weight. A. L. BAILEY and B. A. LANDRY (authors' reply)—The authors thank Messrs. Anderson and Keller for their comments based on long experience. It is agreed that the involved mixing and riming technique used may be disadvantageous from the standpoint of degradation. Fortunately, the paper does point out that the extended riming was unrewarding in causing further mixing. Two large unknowns remain, however: (1) how much of the mixing from the presumed highly unmixed state in the bed was achieved toward the random state during blasting, loading, transportation, screening, and further transportation to the point where the gross sample was taken, and (2) how much of the mixing took place during the preparation described preceding riming. As has been pointed out by one of the authors.6 the degree of mixing has a very large effect on the size of sample required and there are still too few experimental data to show at what stage of coal handling most of the mixing occurs. The discussion states that the weight of material in a screened fraction, or in a float-and-sink fraction, is more important than the mixing factor. We do not believe that these factors are comparable in this instance inasmuch as our purpose was to give minimum sampling requirements to achieve a preassigned accuracy in the percentages of float, middlings, or sink, and nothing more. The gross sample had already been screened and no further division by screening was made or contemplated; also, it was not intended that the middlings and sink fractions would necessarily be adequate for percentage ash or other determination. In other words, the sample obtained by the method outlined is not intended for washability studies but only for preparation plant control. Further experimental work has been done, since the paper was prepared, to investigate the effect of increasingly larger top and bottom sizes on the variability of float, etc., of a double-screened coal from Western Pennsylvania. Results will be published and eventually attention is to be given to the preparation of sampling specifications. E. H. M. BADGER*—I should like the authors to explain more fully the fundamental assumptions on which their Eq 4 is based. The equation is of the form s2 = p(l - p) which is the usual expression for the (standard deviation)2 when the chance of finding a particular kind of particle in the sample is proportional to the number fraetion, p. But instead of the number fraction, the authors have used the weight fraction, WF/W. The chance of finding a particular kind of particle in the sample can only be proportional to the weight fraction, if the average ?eig?ts of all kinds of particles, that is, float, midlings, or sink, are the same. Surely a much more justifiable assumption would be that the average volumes of the particles are the same, and, if this is so, Eq 4 would not be true. This may be demonstrated as follows: Let be the weight fraction of float, middlings, or sink, dl the density of this fraction, and d2 the density of the rest of the coal. Then assuming that the average volumes of the pieces in the three classes are the same, the number fraction, p, is given by ? P = d1/l-?/d2 + ?/d1 = ?d2/d1 + ?(d2-d1) The weight fraction, w, in terms of p is given by ? = pd1/(l-p)d2 + pd1 = pd1/d2 + p(d1-d2) _____ [61

Jan 1, 1950

By E. L. Anders

The Mile Six pool is located on the La Brea-Parinas Cullcession of International Petroleum Co., Ltd., in northwestern Peru on the west coast of South America. The reservoir pressure in this pool has been maintained within 200 psi of its initial value throughout its history, and gravity drainage has played an important role in the production behavior. It has now produced 95 per cent of its estimated ultimate recovery. It is estimated that this interesting oil pool will ultimately produce 67 per cent of the initial oil in place and that the resulting residual oil saturation may be as low as 19 per cent of the pore volume (29 per cent of the hydrocarbon pore volume). An evaluation of reservoir rock and fluid characteristics and ultimate oil recovery is presented. INTRODUCTION This study of Mile Six pool was made to evaluate its performance according to latest available information. The production performance of this pool has been discussed in various articles in the past. and the reported behavior has been used as an example for application of computation procedures for gravity drainage depletion' and as an illustration of field behavior under gravity drainage or expanding gas cap drive. There have been wide variations in reported values of initial oil in place, reservoir oil volume factor. connate-water sauration, volume of effective sand, and ultimate recovery because of the paucity of reliable basic data. These various factors have been determined as accurately as practicable with the latest available information, and this evaluation is presented herein. The production history of Mile Six is an excellent example of gravity drainage depleion with effective pressure maintenance by gar injection. GENERAL Mile Six pool was discovered by cable-tool drilling in November. 1927. when well 1996 was completed in the Parinas sand. After slow development with cable tools and sporadic production. the pool was opened to continuous pro(iuction in November. 1933. and develpment was completed with rotary rigs. Pressure maintenance was started in December, 1933. by returning gas to upstructure wells. Most of the development was 'completed by 1937, but some additional wells were drilled in the period 1939-1947. and several old wells were deepened. A total of 46 oil and gas wells and 4 dry holes were drilled on approximately 7-acre spacing. Of the producers. 21 are now flowing. 2 are pumping. 44 are gas input wells. 3 are abandoned. I is a gas well shut in. and 15 are shut in because of non-commercial production or high gas-oil ratio. The locations of all wells are shown on the map of Fig. I. Total oil production on Dec. 31. 1952, was 30,867,373 bbl: cumulative gas production was 22,023,777 Mcf; and 26,410,946 Mcf of gas had been returned to the reservoir. These figures do not include oil and gas lost ill a blowout in January. 1940. GEOLOGICAL DESCRIPTION Mile Six pool is located on the northern end of a structural spur projecting from the La Brea-Negritos uplift.' The spur is probably a reflection of a basement structure. It plunges gently to the north, i broken into a complex series of fault blocks. and contain.; the Verdun Alto. Section Sixteen. and Mile Six pools. The Parinas handstone (lower Eocene!. which is the producing formation in Mile Six. occurs at an average depth of 2,200 ft in the pool and dips north and east at from 15' to 20". The pool covers an area of approximately 350 acres. Mile Six is downfaulted about 600 ft from Section Sixteen pool to the soutb. and a major fault forms its western boundarv. The north and east boundaries are formed by the intersection of the sand top with the water-oil contact which occurs at approximately 2.440 ft subsea. An original gas-oil contact probably existed at about 1.875 ft subsea. Fig. 1 presents the latest structural interpretation of the pool. and Fig. 2 is an isopach map showing thickness of the total Parinas formation above the original water-oil contact. The heavy lints of Fig. 1 are contours on the sand top, and the fine lines are contours on the fault planes. This type of straight-line structural map was developed 1)) International's geologists to reflect structural conditions where the bedding planes dip and have no curvature. 'The La Brea-Parinas Concession is highly faulted by normal fault.. The beds are flat wherever exposed. The Parinas formation is approximately 635 ft thick. and it is etimated that 62 percent II the formation is effective sand. The original oil zone was about 565 ft thick. Fig. 211 presents an electric log showing typical Parinas sand development ill Mile Six pool. The Parinas band in Mile Six i. a well-sorted. medium- to-coal-se-grained. cross-bedded sand with minor lenses of shale and small lenses and pockets of pebble conglomerate. The sand grains are subangular to rounded and consist chiefly of quartz with feldspars. biotite hornblende, and augite as accessory minerals. Because of faulting of the Parinas- formation to the east and north of the pool. there is probably l possibility of a significant, natural water drive in Mile six. The faults within the pool. as indicated in Figs. 1 and 2. are of smaller disI,laceInent and seem to act only , partial barriers to fluid movement within the reservoir. RESERVOIR CHARACTERISTICS Core analysis data are available from five wells. The data were obtained from three wells (Nos. 3401. 3586 and 3719) at the time of their completion and from well 1996 when the original liner was sidetracked and the well was deepened ill 1946. Data from well 2779 were obtained in 1943 from old cores taken when the well was deepened in 1934. From these core analyses. the average porosity was estimated to be 22.6 per cent. and the average permeability to dry ail. was estimated to be 780 and Measured productility indices varied from 3.1 to 71.4 B/D per psi differential. Specific productivity indices varied approximately from 0.1 to 0.3 B./D per psi per ft of sand.

Jan 1, 1953

By H. I-Lieh Huang, O. D. Sherby, J. E. Dorn

RECENT investigations1-4 have suggested that the total plastic strain, C, for high temperature creep under a given stress can be correlated by means of a temperature-compensated time, te- where t is the duration of test, e is the base of natural logarithms, aH is the activation energy for creep, R is the gas constant, and T is the absolute temperature. A typical set of data on which this deduction was based is given in Fig. la. Inasmuch as the e-in t curves for the various temperatures are identical except for their displacement along the In t axis where f and are appropriate functions. If the increase in creep rate with an increase in temperature is exclusively ascribable to a single process involv- ing thermal activation, (T) should equal RT and therefore it = constant [2] where ?= te Assuming the validity of this relationship, ? = ?2 at the same strain, or where the subscripts refer to two alternate test conditions.

Jan 1, 1957

By R. M. Wilhelm

HIGH-TEMPERATURE thermometry,, as treated in this paper, deals with the measurement of temperature in the range 100° to 550° C. The lower limit corresponds to the temperature of boiling water at normal atmospheric pressure, the upper limit is approximately the highest temperature to which mercury in a glass thermometer may be safely subjected.1 In this range., the domains of pyrometry and thermometry overlap somewhat, for high-temperature resistance thermometers and thermocouples generally classed as pyrometers are often used below 550° C. This paper will be confined to high-temperature mercurial thermometers, and indicating and recording thermometers of the vapor pressure, liquid or gas filled, and bimetallic or graphite-metal expansion types, a classification of which is as follows: CLASSIFICATION OF THERMOMETERS GENERAL CLASSIFICATION SUBDIVISIONS Mercury in glass Laboratory- Etched or engraved stems (mercurial) Enclosed scale (Einschlus) Industrial Vapor pressure Indicating and Pressure Liquid filled recording Gas filled Bimetallic Graphite-metal expansion

Jan 9, 1919

By Rudolph G. Wuerker

WITH the growing complexity of ore dressing processes and the diversity of equipment, efficiency control has become increasingly important in beneficiation. In the case of iron ore dressing, there have been sporadic attempts'-3 to establish the optimum separation for various ores so that grade and recovery would be readily predictable. But no rigorous statistical analysis and graphical presenta- tion of such tests could be found in the literature of this country. Tests Made with Iron Ores Expanding upon existing methods of plant supervision and efficiency control, an investigation was started in the ore dressing laboratory at the University of Illinois on the applicability of distribution analysis to iron ores. A sample of crude ore was obtained from the Ohio mine of Cleveland-Cliffs Iron Co. at Ishpeming, Mich., consisting mostly of alternating bands of hematite and siliceous gangue, both about 1/4 in. wide. The ore was heavily coated with limonite, which often filled the cracks.

Jan 1, 1959