Search Documents

By Samuel Hoyt

THE hardness of annealed copper has been given in the literature and is easily obtained by any of the standard methods of hardness testing. It is not our intention to correct published values or to add to them, but to describe tests of two bars of annealed electrolytic copper in which the methods of Meyer's analysis were employed. MEYER'S ANALYSIS OF BALL INDENTATION TEST The ball indentation test is probably the most valuable hardness test we now have but, as it is carried out in the Brinell or Rockwell test, the result may be seriously in error without the operator suspecting such to be the case. This condition results from the isolated and uncontrolled nature of the measurement. The accuracy depends on the accuracy of the equipment and the care and skill used in the operations; there is nothing in the impression diameter, which is all that is measured, to indicate the presence of error. Meyer's analysis supplies a control of the measurements that goes far toward eliminating unsuspected errors. The principles of this work maybe obtained from elsewhere.1 As this subject has not received the attention of this Institute, it may be well to summarize the more important points as follows.

Jan 2, 1926

By Clyde E. Williams

MORE has been said about the iron and steel situation on the Pacific Coast than has been done .about it; but perhaps as much has been done as conditions have warranted. The production of finished steel in an amount sufficient to take care of the local demand for certain sizes and shapes is an established industry on the .coast. The amount .and the variety of products, so made, changes with the demand or them which is largely dependent upon the growth in population. An increasing demand will not always increase the quantity of steel produced locally because the cost of production may rise so -high as to let in steel from the outside. The reason for this is that all of the steel made in the West comes from steel scrap, the supply of which is .limited. From the standpoint of the metallurgist, it would. be desirable to subititute pig iron for some of ' the steel scrap, but this cannot be done profitably because the pig iron now available is too expensive. In other words, the large future demand for steel and pig iron on the Pacific Coast must be supplied by reduction of ores in the West, unless we are to be content with paying high transportation costs for material produced elsewhere. ."

Jan 1, 1924

By William B. Heroy

LOOKING back over the industrial and commercial progress of the United States during the last half century the outstanding influence has been the growth of the use of the fluid fuels, petroleum and natural gas. At the turn of the century these fuels supplied only 8 per cent of the energy requirements of the nation. Last year nearly 45 per cent of our heat and power supply were derived from these fuels. These figures are merely statistical reflections of the fundamental change in our national economy which has affected, in so many amazing ways, the life of this generation. The factors which have caused this change are still operative. The trend which has thus been established still continues and growth in the use of these fuels is, in all probability, still well below the peak, both for this country and for other parts of the world. Two great wars have not essentially changed this basic trend; if anything they have served to accelerate it. World War II did not alone increase our requirements for liquid fuels; it demonstrated the absolute essentially of petroleum resources to our national security. Petroleum is no longer just an important factor in our national standard of living; it is the most important single element in our national defence-

Jan 1, 1946

By L. H. JEFFRIES

In the mining operations of The Canyon Corp., Deadwood. S. D., the use of mucking machines has been of definite advantage. The type used is that which depends upon the traction of the motor-driven wheels to crowd the dipper into the muck pile, while the car in which the muck is received is coupled to the mucker and moves forward or back with it. This general arrangement is entirely satisfactory on a substantially level track. The ores which occur in this district are a replacement of dolomite and the beds are now tilted to an inclination of about 7-1/20. In our operations it is necessary to drive inclines down-hill on this slope, which makes a difficult hand-mucking job even if water were not present. With these facts in mind, an attempt was made to use the mucking machine for driving down the in- cline, but as expected, the traction was insufficient to handle the machine and the necessary car. The means used to correct this condition will perhaps impress most readers as too complicated and cumbersome to effect any economy, but the idea may be of service to some who have a similar condition. After considering several s

Jan 1, 1940

The useful minerals can be subdivided into two large groups. One comprises those which are mined because of their chemical composition. They represent the natural resources of certain materials or of energy (coal). The second group is used not because of their chemical composition but because of certain physical properties or combinations of physical properties. A large number of minerals are mined because of their hardness, their electrical and thermal properties, their color or plasticity. There has been increasing recognition of the value of mineral synthesis during the past 30 years. This is illustrated by the development of improved aircraft spark plugs and chemical porcelain about the time of the first World War. During World War II the impact of crystal chemistry upon ceramics became most pronounced. New ceramic bodies were tailor-made, such as those designed with a high dielectric constant and low power loss, for use in high-voltage, high-frequency communication. In the field of refractories special materials were needed for unusual heat-resisting service in jet and rocket engines, and in the processing of fissionable materials. The synthesis of natural minerals in the laboratory has long been of aid to geologists and mineralogists in their study of the origin of minerals and physico-chemical conditions under which certain minerals were

Jan 1, 1950

By George Beavers

FLASH roasting of iron concentrate is in the experimental stage at Copperhill. The problem is peculiar in that the iron concentrate is predominantly pyrrhotite; the ratio of that mineral to pyrite being 5 to 1. Results so far indicate that the heat, generated in roasting a material containing 52.0 per cent iron and 38.0 per cent sulfur, requires special handling and for this reason the installation costs per ton of roaster feed may be too great to compete with hearth roasting. Interesting features of flash roasting at Copperhill are: 1. The sulfur dioxide content of the roaster exit gas can be varied between wide limits. Eight per cent sulfur dioxide gas, with 1.30 per cent sulfur in the calcine, has been common practice and gas up to 13.0 per cent sulfur dioxide has been possible. 2. Temperatures of the exit gases are very high. When roasting 60 tons or more of iron concentrate per 24 hr. in a modified Wedge roaster, the temperature in the roaster rises to 2000° F. and the calcine is lowered to 0.20 per cent sulfur. If the entire roaster system could be constructed to withstand such temperatures, ideal roasting conditions would obtain as regards sulfur elimination and tonnage roasted.

Jan 1, 1934

By I. Fatt

Study of a model which contains "dead-end" pore volume indicates that pressure transients are influenced by the amount of dead-end pore volume and by the resistance of the flow path between the dead-end pore volume and the main flow channels. A semi-empirical method is demonstrated that makes possible measurenment of the volume in the dead-end pores and the total pore volume. The difference between these two volumes is the volume of the flow channels. An indication of the flow resistance between the dead-end pore space and the lain flow channels is also obtained. INTRODUCTION In some engineering calculations the distribution of pore volume in a petroleum reservoir need not be known. For example, a material balance calculation treats a reservoir as an oil-filled tank. In other calculations the distribution of pore volume appears implicitly through use of the porosity and the relative permeability and capillary pressure characteristics. It is the purpose of this paper to point out that under certain conditions the exact distribution of pore volume must be known in order to interpret correctly transient flow behavior. Pressure transients during single-phase flow in porous media are usually said to obey differential equations of the form

By F. W. Bremmer

THE drilling of constantly deeper oil wells has made it imperative that the manufacturer of casing be ever searching for new methods and new materials to meet the increased demands. One phase of this search constitutes the subject matter of the present paper. Starting from the original Drake well in 1859, the depth of wells has advanced by leaps and bounds, until today depths of 6000 to 8000 ft. are common. Conditions point to the necessity for drilling to greater depths, and it is not at all improbable that much of the future oil produc- FIG. 1.-TREND IN DEPTH OF OIL WELLS. tion will be from, wells around 10,000 ft. deep. The trend to deeper wells is nicely illustrated by the curve in Fig. 1.1 The points plotted are the maximum depths attained in the various pools which were at their peak for the years given. It may be of some interest to observe the change that has taken place in the tensile and collapsing stresses over the last 25 years. The pressure at the bottom of a 900-ft. hole, equivalent to the pressure caused by an equal column of water, is only 450 lb. per sq. in. The equivalent

Jan 1, 1930

A small group of members of the Institute headed by W. H. Shockley, has insistently demanded that the Institute submit to the members for letter ballot the question of our using in our publications and corre-spondence certain so-called "simplified spellings." The principal argu-ment in favor of this proposal is written by Mr. Shockley and will be submitted in full to the membership for ballot. It rests chiefly on the desirability of saving the time of school children in the learning of the spelling of the English language. A sample of correspondence had with one of the gentlemen on this subject is given herewith in order that members may see what the correspondence and publications of the Institute would look like if we adopted the proposals. This sample was chosen at random: "Onse I condemd the report ov a president of the Institute. He did not pruve his case even on paper-"a hot air profet," I sed. Time has pruved he was." "I rote yu about the muvement to better the spelling in the Institute Bulletin, etc., neglecting to say some things that I mite hav said and things hav happened since which no member ov a democratically governed society shoud stand without protest."

Jan 12, 1919

A new departure of unusual importance in Institute annals was in-augurated by the trip of President Philip N. Moore to the Local Sections at Nevada, Southern California, San Francisco, Seattle, Spokane, Montana, Utah, and Colorado. Everywhere the visit of the President was the occasion of an enthusiastic and successful meeting, which is reflected in the account, published under the different Sections in this and other Bulletins. The President also joined the members of the Columbia Section in their visit to Nelson, British Columbia, at the International Mining Convention, which was attended by mining engineers of Canada and the United States. The President of the Canadian Mining Institute, as well as the officers and members of the Western Section also attended this convention. For full particulars we recommend to our readers the ac- count of this very interesting meeting, which is given on another page of this. Bulletin. It is believed that this is the first meeting between the mining engineers of America and any other country since America joined the Allies. The Secretary of the Institute accompanied the President at the first four meetings and was expecting to attend the others also, but was called home by a death in his family.

Jan 7, 1917

GEORGE K. BURGESS,* Washington, D. C. (written discussiont).-Professor Sauveur refers to the International Aircraft Standards Board in terns that would indicate his non-familiarity with, the organization and the working of this Board which, of course, is excusable on account of Professor Sauveur's absence in Europe at the time. He implies .that the work of this Board was entirely dominated by American interests, whereas diametrically the opposite was the case. The Board, was organized for the purpose of facilitating purchase in the United States, on the basis of common specifications, by the Allied air, services in the United States, and the Board performed a very valuable service in unify-ing the specifications of Italy, Great Britain, France, Canada, and the United States for such purposes. The proceedings of the Board were car-ried out on the basis of unanimous agreement of the representatives of the five countries and all the members from each of the countries were technical specialists or, had the advice of technical assistants. It would be difficult to find an instance of greater unity of purpose, readiness to' compromise, and efficient production than was shown by this Board, which produced seventy-eight specifications, in the preparation of which representative American manufacturers appeared before the Board.

Jan 12, 1919

GEOLOGY is of service to man in two general ways according to Heinrich Ries in The Scientific Month-ly. The first of these is in exploring and evaluating the mineral resources on which industry and civiliza-tion are built, and the second is the application of geo-logic principles to various lines of human activity, such as engineering, agriculture, chemistry, etc. Both of these are phases of economic or applied geology, but neither could be developed before geology as a pure science was more or less firmly established, and in this process it freely acknowledges its indebted-ness to some of its older sister sciences such as chem-istry, physics, botany and zoology. Chemistry and geology are mutually helpful. Various chemical industries consume large quantities of raw mineral products, but since these vary in their purity and composition, it is important for the chemist to be familiar with the irregularities of composition which the different types may show, because he is often called upon to pass judgment on new sources of supply. Here geology helps the chemist. On the other hand, the laws of physical chemistry which the chemist has worked. out are of great assistance to the geologist in explaining many geologic processes.

Jan 7, 1927

By Harry R. Hall

The proposition to make pig-iron from magnetic concentrates and cobbed ore with charcoal-fuel weighing from 12 to 20 lb. per bushel is, on the face of it, not inviting; but the work that has been done under these adverse conditions may be worthy of record as furnishing a comparison with coke blast-furnace practice under similar conditions.' The record of the furnace-practice is briefly summarized as follows :—the charcoal was made of hemlock, pine, spruce, balsam, maple, beech and birch woods. All the concentrates, containing from 62 to 65 per cent. of iron, would pass 1/8in. screen, of which about 34 per cent. would pass an 80-mesh screen. The cobbed ore, varying in composition from 32 to 47 per cent. of metallic iron and from 23 to 32 per cent. of silica, would pass through a 1-in. ring, and of this ore about 25 per cent. would pass a 1/8-in. screen. The furnace was blown-in October 20, 1903, with charcoal which was supposed to weigh, when dry, 18 lb. to the bushel. Some charcoal similar to this was stored in the stock-house for about a year, and was then found to weigh 12 lb. per bushel.

Jan 1, 1906

ARTHUR KNAPP, Ardmore, Pa. (communication to the Secretary*). -The author has failed to consider the point which in my mind is the most convincing in advocating some sort of a bureau for the collection of well logs. I venture to say that 90 per cent. of the logs as taken today are absolutely worthless to any one but the one who has taken the log. This is largely due to the careless use of nomenclature. The author says on page 289, "He must ascertain which of the many factors might account for the dry hole in question and often only careful examination of well logs will convey this information." I believe that even a most careful examination of the average log reveals nothing. I have at hand a book on petroleum, by a well-known author. This book has a number of logs from fields all over the world, from which I shall illustrate. In a well log from Kansas I find "Soft gray shale" and in one from Humble I find "Hard blue shale." As a matter of fact the shale from Humble is softer than the shale from the Kansas well. The difference is that the drillers in Kansas, being used to limestone and

Jan 5, 1917

The Office of Price Stabilization broke the copper price loggerhead between the U. S. and Chile when it permitted copper wire and brass mills to add to their ceiling prices 80 pct of the increase in cost of foreign copper above the 27 1/2 cents per pound specified in the agreement with Chile. Another step forward in the processing of taconite seems to have been made with the patenting of a process for the strengthening of taconite pellets. The patent was issued to Fred D. De Vaney and assigne to the Erie Mining Co., of Hibbing, Minn. Strength of the pellets is improved by adding from one to five pounds of starch or sodium silicate. A new iron ore deposit discovered on Vancouver Island will start producing soon, and is expected to yield 2 million tons of magnetite over its span of operation. A new mill will be built by the Argonaut Construction Co., of San Francisco, at the deposits of the Utah Construction Co., its parent organization. The Organization for European Economic Cooperation banned the use of nickel and nickel alloy in the manufacture of about 500 products in an attempt to conserve nonferrous metals in short supply. Some 18 members of the organization have already volunteered to restrict nickel consumption.

Jan 1, 1952

L. S. PANYITY.-I made inquiries from the Smith and Dunn people, who are the originators of the compressed air and gas method of increasing the production of oil wells, as to how much pressure the sand will stand; that is, relative to the original rock pressure. They tell me that they have not been able to show, up to date, any pressure in a sand greater than the original pressure. I have also made 'a statement to that effect, but I am really dubious as to whether that is right, as I am not sure that you cannot get a greater pressure. However, I think that a greater pressure would be dangerous because it might cause a loss of gas. C. H. SHAW, ? Lawton, Okla.-In regard to the gas that was put into the pool up in New York State, may it not be possible that, on account of errors, etc., in measuring or computing, there is a mistake in the apparent fact that more gas was gotten out than was put in? L. S. PANYITY.-Unfortunately, I have not the papers I expected from those people to show the actual conditions, but I do not doubt that such

Jan 4, 1919

Meeting of Nov. 21, 1913.-The President reported the appointment of the officers and members of the Committee on Non-Metallic Minerals, published elsewhere in this Bulletin. The President appointed the Executive Committee of the New York Section as a local .committee to have charge of the Annual Meeting of the Institute in February, 1914, with power to add to their numbers. It was voted that the Chairman of each Technical Committee, be made ex officio a member of the Committee on Papers and Publications. At the request of the Secretary, Burr A. Robinson was appointed Assistant Secretary of the Institute. E. Gybbon Spilsbury was nominated as representative of the Institute on the John Fritz Medal Board of Award. It was voted that the next summer meeting of the Institute be held in Salt Lake City in August, 1914, with power to the Executive Committee to fix the exact date. Substantial reduction was made in the price of the back Transactions of the Institute in accordance with the notice published on p. i of this Bulletin.. The By-Laws of the Montana Local Section were approved. The printing contract for the year 1914 was made with the Maple Press. Thirty-eight Members, one Associate and three Junior Members were elected.

Jan 12, 1913

What do you think are the major problems that the mining industry is facing? While I don't have any intensive knowledge of the various problems that plague our industry, I know that they are all part and parcel of a more complex and fundamental question: What must we do to make mineral extraction successful, safe, and profitable? Obviously, as mining people, we must continue to expand our technical know-how and to make better use of it. In today's context, however, that is not enough. We must also improve the "public image" of the mining industry. Why? Because the key word in the term "public image" is: the public. Many people in our country and in Congress, for instance, are against strip mining-and some are even against underground mining. Pressures from the public, from voters, have affected past, present, and new legislation. And government controls can be a major problem in any industry, let alone mining. At first, people ask government to intervene, act, or resolve problems, even in management and labor contract negotiations. But later, after Washington gets involved, there are clashes between departments and personalities, and eventually there is resentment against the interference with mining operations or our daily lives.

Jan 3, 1975

By Yoshinao Nakada

In many experiments involving electropolishing such as electropolishing during deformation and electrothinning of deformed metals for electron microscopy, it is usually assumed that the specimen temperature is the same as the temperature of the polishing bath. In order to test this assumption, the interior temperature of aluminum single and polycrystals was measured while they were being electropolished. Specimens were 1/4 by 1/4 by 6 in. and were of 99.99 pct purity. A small hole 1 in. deep was drilled axially at one end of the specimen so that a copper-constantan thermocouple could be inserted. The electropolishing solution was 4 parts methanol (reagent grade) and 1 part perchloric acid (70 pct). The electropolishing was performed using an apparatus shown in Fig. 1. The electropolishing solution was stirred by a motor-driven stirrer and was cooled to —5°C with a mixture of methanol and dry ice. Electrolyte temperature was measured and remained at -5°C during the electropolishing. Current density of 0.3 amp per sq. cm was used. When the current was turned on, after about a 5-sec delay, the temperature began to rise rapidly until it reached 65°C. In order to determine whether the temperature measured was localized, the thermal expansion of the specimen was meas-

Jan 1, 1965

By David Baker

In a paper presented to the American Institute of Mining Engineers, September, 1904, entitled uImprovements in the Mechanical Charging of the Modern Blast-Furnace,"' I showed the great fault of mechanical charging-devices to be that the materials charged by the dumping of the skip were separated, the coarse materials having high velocity, and the fine, low— thus giving paths of low resistance through the stock in the furnace, which resulted in unequal distribution of the furnace-gases, unequal reduction, slips, scaffolds, irregular cutting of the inwall, "of" iron, and increased fuel-consumption. I showed how this could be prevented by rotary distribution, through which the irregular distribution in one layer charged is compensated by charging the subsequent layers from succeesively varied positions of the charger, and becomes practically eliminated when the angle between two successive positions is a little more or less than an even fraction of a full circle. Of all the devices then on the market, the nearest approach to the ideal arrangement was found in the Brown distributor, a full description of which was given. The one defect pointed out, however, was the difficulty of maintaining so much mechanism on the top of a blast-furnace. Since the presentation of that paper, I have designed a very

Jan 1, 1907