Search Documents

By F. M. Waring

produced when zinc is substituted for a certain amount of tin are decidedly unsatisfactory. The substitution of aluminum for tin is entirely impractical, and such castings are worthless. This does not, however, exhaust all the possibilities of substituting other metals for tin in the copper-tin-lead alloys, but it is my opinion that the substitution of any other metals, in those alloys, can be made only by sacrificing the quality of the alloy. The possibility of substituting alloys of an entirely different type presents an attractive field for research. The copper-tin-lead alloy has attained its position as the most desirable bronze bearing alloy, but this does not mean that some other alloy may not be found which may give equally good or better results. In the search for such a substitute alloy it should be borne in mind that a bearing metal should possess the following properties: (1) It should be sufficiently rigid to support the load or resist the impact, but yet not so brittle that it will easily crack. (2) It should have as great a yielding or plastic nature as is consistent with its ability to support the load or resist the impact without deformation of the bearing as a whole. (3) The ideal structure combines a hard matrix to support the load and a softer metal or alloy contained within such matrix, to permit the bearing surface to adjust itself to irregularities of service. (4) It should be easy to handle in the foundry and machine shop. (5) It should be capable of being remelted without deterioration. (6) For use in babbitt-lined bearings, it should be capable of being tinned, so that the babbitt can be applied thereto. (7) It should have good heat conductivity in order to dissipate the heat generated by friction. Pennsylvania Railroad Anti-friction and Bell Metals F. M. Waring," Altoona, Pa.—Thc necessity for conserving tin has recently been very forcibly brought to the attention of all consumers, and efforts are now being made to reduce the tin content in certain alloys or to substitute other alloys not containing tin. The approximate composition of the non-ferrous alloys in general use on the Pennsylvania Railroad are given in the accompanying table. Phosphor bronze is used principally for rod bushings, main-rod brasses, and crosshead shoes. Ex. B bronze is used to a small extent for backs of car and coach bearings, but the majority of these are now made of the car-journal bronze, which contains, on the average, about 5 per cent. tin.

Jan 1, 1919

By T. Koulomzine

The theory of the Askania mag-netometer, as well as a complete discussion of all factors influencing magnetometer readings, is very ably described by J. Wallace Joyce.1 We will assume that the reader is thoroughly familiar with this theory and we will use whenever possible the same notations for the physical values involved in the theory. On the other hand, we believe that the principal formulas of the magnetometer can be deduced much more easily by the use of differential calculus than by the methods employed by Joyce. Consequently, we are presenting herewith a resumé of the theory of the vertical magnetometer in order to determine the correct formula of the temperature coefficient which we propose to compensate. Short Theory of the Vertical Magnetometers We shall accept the following notations: m = total mass of the magnet system, in grams. g = acceleration of gravity, in dynes. a = projection on the axis of the magnet system of the distance between the axis of support and the center of gravity of the magnet system, in centimeters. h = projection on the perpendicular to the axis of the magnet system of the distance between the axis of support and the center of gravity of the magnet system, in centimeters. M = 2pL = M, magnetic moment of the magnet system. Z = vertical component of the earth's magnetic field. ? = deflection angle of the magnet system. = focal length of objective lens in the optical system S = scale reading. In a vertical magnetometer the axis of the magnet system is kept horizontal within 2". Therefore, referring to Fig 1, we see that the magnetic torque of the magnet system influenced by Z must be counterbalanced by the gravity torque. MZ cos ? = mga cos ? + mgh sin ? or dividing by cos ? MZ = mga + mgh tan ? If we now move to another magnetic station and the temperature conditions change, the values of all the variables will change also: M, a, and h under the influence of temperature. 2, both with time and space. ? and S, as a result of all the above changes. Taking increments in Eq 2 we obtain: (Mo + ?M)(Z + ?Z) = mgao + mg?a + mg(h + ?h) tan (? +??) but tan (? +??), because ? is small, can be replaced by tan ? + tan ??; in fact tan (?+ ??) = sin ?.cos ?? + cos ?.sin ??/ cos ?.cos ?? — sin ?sin ?? but sin ? sin ???0 tan (8 + ??) ? tan ? + tan ??. Fur-thermore, neglecting all terms of the equation containing two differentials becomes: or a differential and a tan ??, Eq 3

Jan 1, 1950

By W. M. Corse

I bring this investigation to your attention to emphasize the needless waste attendent upon the use of tin plate with an unnecessarily heavy tin coating. With our present knowledge, we are unable commercially to produce coatings as light as the lower weights used in this test. If, however, future research should develop means to this end, the resultant product would meet all practical requirements, and a very considerable saving in pig tin would result. DISCUSSION G. H. Clamer.-—The National Canners' Association is studying the action of fruit juices, etc., on solders. Of course these tests will take quite a long time, and we hope by that time the war will be over and there will be no need for conserving tin for war purposes. Germany for a great many years has prohibited the use of more than 37 per cent. of lead in alloys used in contact with food products. The eutectic composition is 37 per cent. of lead and 63 per cent. of tin; alloys containing more than that percentage of lead have some free lead. J. W. Richards,' South Bethlehem, Pa.—A great deal of conservation can result from the packing of dry foods in cartons and in fiber packages instead of using sheet tin. Many of the boxes used for packing things other than food are frequently made of sheet tin because it prints and lithographs well; these could be made of sheet iron coated with copper or some other substitute metal which prints equally well. The Aluminum Bronze Industry W. M. CORSE,† Mansfield, Ohio.—The conservation of tin, in view of the shipping situation, is one of great importance. Several methods of conservation can be employed: 1. Reduction of the amount of tin in an alloy or compound. 2. Substitution of an entirely different metal or compound for tin. 3. A combination of the first and second methods. The second method is the one that I wish to discuss. Metallic aluminum, has been known for a long time, and its use in copper alloys was discovered about 1855 by Lord Percy. The high cost of production of metallic aluminum retarded its commercial development, and it was not until the discovery of the electrochemical processes for its production that it came to be known as a common metal. I have been particularly interested, for the past few years, in working with the alloy known as aluminum bronze, which is usually composed of approximately 90 parts of copper and 10 parts of aluminum, by weight.

Jan 1, 1919

By Clarence Zener

The internal friction of nonferrous metals vibrating at low stress amplitudes has so far always been successfully interpreted in terms of inhomogeneities of one sort or another. Examples are the fluctuation of stress across a specimen vibrating transversely,1,2,3 the stress inhomogeneities due to the elastic anisotropy and partial random orientation of the individual crystallites, localized weak regions introduced by cold-working,6'7 grain boundaries and possibly twinning planes.8'9 Perfect single crystals are, by definition, homogeneous. Actual single crystals usually, perhaps always, contains some imperfections. The present investigation was undertaken to determine whether the internal friction of single crystals may likewise be attributed to inhomogeneities. This study was made possible through the gift of a large single crystal of 70-30 alpha brass by H. L. Burghoff, of the Chase Brass and Copper Co. The specimen, 3.i in. in diameter and 10 in. long, was similar to samples previously described by Mr. Burghoff. Experimental Method The experimental method used has previously been described in institute papers.5'6'9 The measure of internal friction adopted here, I/Q, is X the logarithmic decre- ment, a measure used by some writers, and is also X the specific damping capacity, a measure used by other writers. In all measurements the stress level was kept so low that the measurements were independent of stress level. In all measurements in which the temperature was varied, observations were made as the specimen slowly cooled from its highest temperature. The specimen was vibrated transversely. Observations were made at the fundamental frequency and at the first overtone, of about 620 and 1710 cycles per second, respectively. No attempt was made to avoid acoustical losses. Experimental Results The specimen was annealed for several hours at 450°C. The temperature dependence of the internal friction was then determined from room temperature to 400°C. As shown in Fig. I, the internal friction increased by only a factor of 2 from room temperature to 300°C., then by a factor of 100 during the next Ioo° interval. These measurements are consistent with the view that the observed internal friction is the superposition of two distinct parts. One, dominant at room temperature, is nearly independent of temperature. This part may be accounted for by acoustical losses and by transverse thermal currents. It was not further investigated. The second part, when plotted in the manner of Fig. I, lies upon a straight line. Therefore it has a heat of activation H; i.e., it varies with temperature as Internal friction e-H/RT [I]

Jan 1, 1943

By Lucien Eaton

IN anticipation of a shortage of labor for hand-tram-ming at the Cliffs shaft mine of the Cleveland-Cliffs Iron Co. at Ishpeming, Mich., early in 1923 three 4-ton Goodman storage-battery locomotives, equipped with Edison batteries, were purchased. Storage-battery locomotives were chosen for this work because the expense and time required to put up trolley-wire and to bond the rails of the complicated system of tracks on the levels, where the locomotives were to be used, would not have been warranted by the amount of ,ore to be handled. The only changes in the tracks necessary for storage-battery locomotives were new switches and extra ties and braces on curves. The tracks were 24-in. gage, and were laid with 20-lb. rail. Edison batteries were chosen, because it was desired to charge the batteries from the trolley circuit already, in the mine, and this would have been impracticable with lead batteries. Each locomotive is equipped with 126 A-4 Edison cells, which are charged in series from the 240-volt trolley circuit while the trolley locomotives are running; and are discharged in parallel in two banks of 63 cells each. These locomotives were so successful that later 5 smaller locomotives, weighing 11/2 tons each, were pur-chased for use e with cars that are filled by hand and on levels where the amount of ore handled is small. These locomotives, built by the Geo. D. Whitcomb Co. of Rochelle, Ill., are equipped with batteries of 40 A-4 Edison cells each, the cells being the same as those, on the larger locomotives. They are charged from mer-curial-are rectifiers. These locomotives are operated by the trammers themselves, and have not special oper-ators like the larger machines. The trammers are all young men of American birth, and take quickly to the operation of machinery, and the simplicity of the con-trol on these locomotives has made special training unnecessary. A survey of the results was made by the A. C. Nielsen So., an excerpt from which follows: Eight Edison-equipped battery locomotives are now in use at an Ishpeming mine of the Cleveland-. Cliffs Iron Co. This equipment was installed to take the place of men who formerly pushed loaded cars by hand. Results have been very satisfactory and the de-pendable, trouble-free operation of the Edison batteries is considered to have been an important factor in the effectiveness of the new hauling method.

Jan 3, 1927

I HAVE now traversed for you in the small and fragile bark of my writing all the shores of the deep and spacious sea embracing the uses of material fires, drawn on by my own desire to enrich you with more learning and with the procedures of these things, as much as to satisfy your demands. Having through the grace of God arrived at the appointed end of my voyage and neither knowing nor perceiving a way of going farther, I had decided to furl the [167] sails and cast die heavy anchors into the water in order to enjoy in tranquillity respite from my sailing, when I was warned by my pilot that before I could disembark I should turn my glance backward and reexamine my work in detail to see if there were any part that had by chance remained undescribed in the obscurity of silence. When I did this there immediately appeared in my mind's eye the many sublimates and smoky tinctures that had been made by the burning and most powerful fire of love. I need not say that I knew of it in far-off countries or from the knowledge of others, but I knew it in my own breast and as my very own and can therefore surely esteem it as hotter than all the other fires that the world calls by that name. Although today its sparks and living flames are spent because of my cold and hoary season, nevertheless it is true that the memory of acts of love of long ago still remains with some smoke and warmth. Therefore, since in this work of mine I wish to describe for you the effects and powers of fires, I should logically have spoken of this before any of the others, because of its actual nearness and the great acquaintance I had with it. But since I have had the glance of my intentions directed at distant things, I have behaved as one does who does not see where he places his feet because he is looking at the sky, or as one who thinks about the affairs of others and forgets his own. But now I do not wish to pass over this thing and I wish to correct my error, particularly in order to provide a happier ending to my written work than by remaining among the horrible uproar of guns, powder, and saltpeter, which would be a harsher ending than speaking of love. Never-

Jan 1, 1942

HenRy Clay FRick, a pioneer in modern coke and steel industry and, in more recent years, one of the outstanding financiers of America, died on Dec. 2, 1919, at his home on Fifth Avenue, New York. Although he had been ill since election day, when he had an attack of indigestion which developed into ptomaine poisoning, his death was a surprise to all. He is survived by his widow, Adelaide Howard Childs Frick; a son, Childs Frick, one unmarried daughter, Helen C. Frick, and four grandchildren. A quiet funeral service was conducted at the Frick home on Wednesday afternoon by the Rev. Dr. Leighton Parks, pastor of St. Bartholomew's Episcopal Church. This was attended by members and very intimate friends of the family, Trustees of the Metropolitan Museum of Art, Officers of the Links Club, and Directors of the United States Steel Corpn. Henry Clay Frick was born Dec. 19, 1849, in West Overland, Westmoreland Co., Pa. His father, John W. Frick, was a farmer of Swiss ancestG, and his mother, Elizabeth Overholt Frick, a member of an old Mennonite family. Until he was sixteen, he spent his time at school, on his father's farm, and in his grandfather's distillery, where he kept books. He attended Otterbein University, in Ohio, for a year. Frick, learning that coke was an essential of the already rapidly developing steel business, early invested every cent he could get in coking-coal lands. With the help of an associate of his grandfather, he formed the corporation of Frick & Co., coke dealers, and acquired fifty-one ovens in the Connellsville region and 300 acres of soft-coal lands. During the panic of '73, with the help of Judge Thomas Mellon, a Pittsburgh 'banker, he bought out his partners and while coke was selling at 90 cents a ton enlarged his purchases of suitable lands. Later, the price of coke increased until it was selling at $5 a ton. Before he was 30 years old, Frick was rated a millionaire. Association with CaRnegie In 1878, he sold an interest in the business Do E. M. Ferguson of New York, and later a share to Mr. Ferguson's brother. Four years later the business was reorganized into the H. C. Frick Coke Co. with vast coal lands, great banks of ovens, and a capitalization of $2,000,000. Then began his association with Andrew Carnegie. He exchanged a part of his coke interest for shares in Carnegie Brothers of Pittsburgh,

Jan 1, 1920

By Rosewell H. Johnson

Discussion of the paper of ROSWELL H. JOHNSON, presented it the San Francisco meeting, September, 1915, And printed in Bulletin No. 102, June, 1915, pp. 1291 to 1294. WILLIAM A. WILLIAMS, San. Francisco, CaI.-A sliding. scale of royalties was proposed to the Department of the Interior in connection with the fixing of royalties to be charged upon oil leases made on the Osage Reservation in Oklahoma. The possibility of evasion and difficulty of enforcement required close inspection to satisfy all interests, particularly in connection with the exemption from royalty on oil to equal maintenance and interest on the junk. Mr. Johnson discusses the block method, the period method, and the cumulative method, and favors the adoption of the cumulative method with a proviso that the wells should be permitted to be pumped until the gross income is as low as the maintenance cost, which would mean exemption from royalty on the smallest wells. He recommends that depth be the variable factor upon which the sliding royalty is based and suggests that on partially developed territory in the Osage, the royalty be one-sixth for oil wells averaging less than 2,000 ft. in depth, one-eighth for wells from 2,000 to 3,000 ft., and one-twelfth above 3,000 ft.; for the rest of the Osage he suggests one-eighth above 2,800 ft. and one-twelfth below that depth. The net result, if Mr. Johnson's suggestions had been accepted in the Osage, would have been to reduce the then existing rate of royalty and considerably increase the cost of administration. The difficulties in determining the size of wells to be exempt and the possibility of obtaining oil at different depths in the same well might lead to complications which are avoided by charging a flat royalty as now universally charged throughout the United States. It is not uncommon to reduce the royalty when the production of the wells becomes unprofitable at an existing rate of royalty, accomplishing very much the same results as Mr. Johnson has attempted to accomplish by the cumulative royalties, and probably in a manner far more satisfactory to the operator and the lessor. A. C. MCLAUGHLIN, San Francisco, Cal.-The net revenue of the well depends, first, on the cost of production; second, on the amount of oil produced; therefore it would be impossible under Mr. Johnson's system to set a royalty which would be fair to all concerned. If it is impossible to set it at the beginning, it is certainly further impossible to do it from day to clay. I think it is entirely impracticable of application.

Jan 12, 1915

By G. Richards Gwinn

Graphite is one .of the so-called minor nonmetals that have become of major importance during the present conflict. Requirements of the domestic industry for graphite are relatively small and uses have changed so greatly in the past 25 years that different types, with few exceptions, are more nearly interchangeable in use. However, the quality of the graphite required for crucibles is exacting and under present manufacturing practices only a small part of the world production can be utilized economically by this industry. Graphite, for the domestic crucible industry, was supplied almost entirely by imports from Madagascar and Ceylon before the present war. The quantity required has been increased by the war and the greatest demand is for Madagascar flake. The fall of France to Germany in 1941 and the Japanese expansion southward threatened our supply of crucible-grade graphite, therefore the domestic industry was revived to supplement imports and to act as insurance in the event of complete stoppage of imports. Two plants were constructed for the Government, one at Ashland, Alabama, called the Crucible Flake Graphite Co., operated by Haile Mines, Inc., and one near West Chester, Pennsylvania, operated by the Benjamin Franklin Flake Graphite Co. Loans were made by the Reconstruction Finance Corporation to the Alabama Flake Graphite Co. at Ashland, the Ceylon Graphite Co., at Goodwater, Ala., and the Southwestern Graphite Co., at Burnet, Texas. However, by the end of 1943 the import situation had improved and it was no longer necessary to continue Government assistance to mine and stock-pile the high-cost domestic material. Graphite is found in virtually every country of the world. Most occurrences are of no economic importance because of their poor quality, prohibitive mining and milling costs, inaccessibility, and poor location with reference to the industrial centers where graphite is used. The principal commercial deposits are found in Ceylon, Madagascar, Chosen (Korea), United States, U. S. S. R., Canada, Germany, and Mexico. Graphite is a typical international mineral in that it is utilized mainly in countries noted for industrial activities, whereas the two islands, Ceylon and Madagascar, which produce the major part of the world's high-grade graphite, are virtually devoid of any manufacturing establishments requiring its use. The industry thus is violently disturbed by wars. Types oF Graphite Used in Crucibles Graphite of various kinds and from many countries has been used for making crucibles. Passau (Bohemian) flake was first used in Europe, but by the middle of the seventeenth century crucible formulas were established largely on Ceylon graphite and German Klingenberg clay. Ceylon graphite is granular and the grains are subdivided into more or less

Jan 1, 1948

By Mark Sheppard

DURING the winter of 1937, the writer visited a West Virginia stone quarry at which the overburden is stripped hydraulically. The quarry is in a bed of limestone, about 200 ft. thick, which outcrops on a hillside above a small river; the quarry face is 175 ft. high. The top of the stone is cut in all directions by erosion channels, which are filled with a tough, red clay. Some of the larger channels are 30 ft. deep and 8 ft. wide. The thickness of the clay overburden ranges from a few inches to 10 ft., the average being estimated as less than 3 feet. The topography of the district is rugged, and the hillside above the quarry face is not suited to the use of the usual mechanical methods of moving dirt. Until hydraulicking was started 10 years ago, the over- burden was dug by hand labor, dumped to the quarry floor and transported to the dump in quarry cars. Cleaning deep channels was a slow and expensive process. When hydraulicking was started, the top of the quarry face was over 200 ft. above the level of the river. The pipe line was carried in a semi- circle around the top of the quarry about 200 ft. from the face and about 50 ft. above it. As there is no adequate supply of water above the quarry, the water must be pumped from the river. As quarrying progressed the pipe line was moved until the discharge points are now over 300 ft. above the river. Water is pumped from the river by a four-stage centrifugal pump having a 5-in. intake and a 4-in. discharge. It is direct-connected to a 200-hp., 2300-volt, 1760-r.p.m. induction motor. At 1760 r.p.m. the rated capacity of the pump is 750 gal. per minute under a head of 600 ft. The pump is installed in a house of frame construction on the river bank, about 10 ft. above normal water level, which also houses the pump for the mill-water supply. Above the pumps are hoisting bays into which the motors are raised whenever the river reaches flood stage. An 8-in. suction line, equipped with a strainer and a foot valve, takes the water from a concrete sump at the edge of the river. The pipe line from the pump consists of 1750 ft. of 8-in. spiral steel flanged pipe and 800 ft. of 4-in. spiral steel flanged pipe. The connection from the pump

Jan 1, 1938

By Clarence Zener

THE internal friction of nonferrous metals vibrating at low stress amplitudes has so far always been successfully interpreted in terms of inhomogeneities of one sort or another. Examples are the fluctuation of stress across a specimen vibrating transversely,1,2,3 the stress inhomogeneities due to the elastic anisotropy and partial random orientation of the individual crystallites,4,5 localized weak regions introduced by cold-working,6,7 grain boundaries and possibly twinning planes.8,9 Perfect single crystals are, by definition, homogeneous. Actual single crystals usually, perhaps always, contains some imperfections. The present investigation. was undertaken to determine whether the internal friction of single crystals may likewise be attributed to inhomogeneities. This study was made possible through the gift of a large single crystal of 70-30 alpha brass by H. L. Burghoff, of the Chase Brass and Copper Co. The specimen, ½ in. in diameter and 10 in. long, was similar to samples previously described by Mr. Burghoff.10 EXPERIMENTAL METHOD The experimental method used has previously been described in Institute papers.5,6,9 The measure of internal friction adopted here, 1/Q, is (1/p) X the logarithmic decrement, a measure used by some writers, and is also (1/2p) X the specific damping capacity, a measure used by other writers. In all measurements the stress level was kept so low that the measurements were independent of stress level. In all measurements in which the temperature was varied, observations were made as the specimen slowly cooled from its highest temperature. The specimen was vibrated transversely. Observations were made at the funda¬mental frequency and at the first overtone, of about 620 and 1710 cycles per second, respectively. No attempt was made to avoid acoustical losses. EXPERIMENTAL RESULTS The specimen was annealed for several hours at 450°C. The temperature dependence of the internal friction was then determined from room temperature to 400°C. As shown in Fig. 1, the internal friction increased by only a factor of 2 from room temperature to 300°C., then by a factor of l00 during the next 100° interval. These measurements are consistent with the view that the observed internal friction is the superposition of two distinct parts. One, dominant at room temperature, is nearly independent of temperature. This part may be accounted for by acoustical losses and by transverse thermal currents. It was not further investigated. The second part, when plotted in the manner of Fig. I, lies upon a straight line. Therefore it has a heat of activation H; i.e., it varies with temperature as Internal friction e~H/RT [I]

Jan 1, 1942

By L. J. Klinkenberg

It is pointed out that the current concept of pore size distribution is not unequivocally defined and that different methods aiming at a determination of such a distribution therefore do not lead to the same results. A pore size distribution should not be based on the idea that a core should, under all circumstances, behave as a bundle of straight non-interconnected capillaries of the same pore size distribution. This is illustrated by calculations and experiments on the displacement of miscible liquids. INTRODUCTION The introduction of the concept of pore size distribution has been an attempt to characterize the intricate geometry of the flow channels in porous media. As pores in a porous medium are interconnected it is impossible to describe exactly what is meant by a "pore" and, therefore, the term pore size distribution requires further amplification. In the visual method for the determination of pore size distribution "the pore" is considered to be the hole between the grains as observed on thin sections or on a polished surface of the rock under a microscope. In all other presently known methods,1,2 a displacement process is studied and it is ascertained what as- semblaae of straight cylindrical capillaries would show the same behavior. The distribution of the capillary diameters of this assemblage is said to represent the size distribution of the pores of the actual porous medium. From the foregoing it is already apparent that it is useless to try to decide which process or which method of investigation leads to a "correct" pore size distribution. To illustrate this further a displacement process in which a fluid is displaced by another miscible with it will be discussed and the results will be interpreted in terms of a pore size distribution. DISPLACEMENT EXPERIMENTS WITH MISCIBLE LIQUIDS OF NEARLY IDENTICAL VISCOSITY AND DENSITY Interpretation in the Form of a Pore Size Distribution If distilled water is displaced from a homogeneous unconsolidated sand pack by, for instance, a dilute solution of NaCI, the breakthrough recovery i.e., the amount of distilled water produced at the moment the first trace of NaCl can be detected in the effluent water, is between 95 and 100 per cent of the pore volume of the pack. This result can be understood by following in imagination the course of one particle of the liquid. Imagine a length, ?l, at the end of which a liquid particle has an independent chance of a renewed choice of pores of different diameters. In other words, the particle has a choice of traveling time, at, for any length ?l; instead

Jan 1, 1958

By E. C. Harder

J. T. SINGEWALD, JR., Baltimore, Md.-I might say a word further in regard to the Miguel-Burnier district. I am sorry Mr. Harder is not here. I had hoped to be able to ask him a few questions in regard to some of the features of those deposits. This Miguel-Burnier district is the other district that I referred to that lies in the State of Minas Geraes. The interpretation that Mr. Harder gives to, these deposits is the same as that given by Harder' and Chamberlin in a previous paper, and that is that they consist of lenticular deposits of sedimentary origin in a series of rocks that also include lenses of limestone, but they seem to think that the manganese ores occur at a definite horizon and at a horizon different from the limestone. We found that the manganese ores occur at several horizons, as also do the limestone lenses, and the limestone masses are of the same shape as the manganese orebodies, so that our own feeling was that these manganese ores simply represent concentrations within the zone of oxidation formed as. a result of decomposition and replacement of this limestone. To the east of Miguel-Burnier there is a big bend in the railroad which cuts through, at right angles to the strike, this series of rocks. Here is shown very well both the local character of the limestone lenses and the local character of the manganese lenses in that, though the distance across the bend is only a couple of hundred yards, the limestone and. ,manganese lenses do not match up at all, and it also shows plainly that both occur at more than one horizon.. Consequently there is no reason why the manganese ore could not represent alterations of this limestone. The mine workings do not as yet give very definite information on this point in that they are all comparatively shallow and within what would be the zone of oxidation so that what they will grade into below that depth, we do not know. On the other hand, the character of the ore suggests that it may, represent such -a product in the zone of oxidation in that it tends to be quite earthy; whereas, if the manganese had been there originally as such it would have undergone the same metamorphism that the other rocks have undergone and one would have expected that it would have been converted into a hard manganese ore that would today stand out pretty much as do the iron ores of that same region and not have the soft, earthy texture which is a prevailing characteristic.

Jan 4, 1917

By Clarence Zener

THE internal friction of nonferrous metals vibrating at low stress amplitudes has so far always been successfully interpreted in terms of inhomogeneities of one sort or another. Examples are the fluctuation of stress across a specimen vibrating transversely,1,2,3 the stress inhomogeneities due to the elastic anisotropy and partial random orientation of the individual crystallites,4,5 localized weak regions introduced by cold-working,6,7 grain boundaries and possibly twinning planes.8.9 Perfect single crystals are, by definition, homogeneous. Actual single crystals usually, perhaps always, contains some imperfections. The present investigation was undertaken to determine whether the internal friction of single crystals may likewise be attributed to inhomogeneities. This study was made possible through the gift of a large single crystal of 70-30 alpha brass by H. L. Burghoff, of the Chase Brass and Copper Co. The specimen, 3-s in. in diameter and 10 in. long, was similar to samples previously described by Mr. Burghoff.10 EXPERIMENTAL METHOD The experimental method used has previously been described in Institute papers.5,6.9 The measure of internal friction adopted here, I/Q, is (p) X the logarithmic decrement, a measure used by some writers, and is also (I/2p) X the specific damping capacity, a measure used by other writers. In all measurements the stress level was kept so low that the measurements were independent of stress level. In all measurements in which the temperature was varied, observations were made as the specimen slowly cooled from its highest temperature. The specimen was vibrated transversely. Observations were made at the fundamental frequency and at the first overtone, of about 620 and 1710 cycles per second, respectively. No attempt was made to avoid acoustical losses. EXPERIMENTAL RESULTS The specimen was annealed for several hours at 450°C. The temperature dependence of the internal friction was then determined from room temperature to 400°°C. As shown in Fig. i, the internal friction increased by only a factor of 2 from room temperature to 300°°C., then by a factor of 100 during the next :too' interval. These measurements are consistent with the view that the observed internal friction is the superposition of two distinct parts. One, dominant at room temperature, is nearly independent of temperature. This part may be accounted for by acoustical losses and by transverse thermal currents. It was not further investigated. The second part, when plotted in the manner of Fig. I, lies upon a straight line. Therefore it has a heat of activation H; i.e., it varies with temperature as Internal friction ~ e-HI/RT [I]

Jan 1, 1942

By G. Richards Gwinn

Graphite is one .of the so-called minor nonmetals that have become of major importance during the present conflict. Requirements of the domestic industry for graphite are relatively small and uses have changed so greatly in the past 25 years that different types, with few exceptions, are more nearly interchangeable in use. However, the quality of the graphite required for crucibles is exacting and under present manufacturing practices only a small part of the world production can be utilized economically by this industry. Graphite, for the domestic crucible industry, was supplied almost entirely by imports from Madagascar and Ceylon before the present war. The quantity required has been increased by the war and the greatest demand is for Madagascar flake. The fall of France to Germany in 1941 and the Japanese expansion southward threatened our supply of crucible-grade graphite, therefore the domestic industry was revived to supplement imports and to act as insurance in the event of complete stoppage of imports. Two plants were constructed for the Government, one at Ashland, Alabama, called the Crucible Flake Graphite Co., operated by Haile Mines, Inc., and one near West Chester, Pennsylvania, operated by the Benjamin Franklin Flake Graphite Co. Loans were made by the Reconstruction Finance Corporation to the Alabama Flake Graphite Co. at Ashland, the Ceylon Graphite Co., at Goodwater, Ala., and the Southwestern Graphite Co., at Burnet, Texas. However, by the end of 1943 the import situation had improved and it was no longer necessary to continue Government assistance to mine and stock-pile the high-cost domestic material. Graphite is found in virtually every country of the world. Most occurrences are of no economic importance because of their poor quality, prohibitive mining and milling costs, inaccessibility, and poor location with reference to the industrial centers where graphite is used. The principal commercial deposits are found in Ceylon, Madagascar, Chosen (Korea), United States, U. S. S. R., Canada, Germany, and Mexico. Graphite is a typical international mineral in that it is utilized mainly in countries noted for industrial activities, whereas the two islands, Ceylon and Madagascar, which produce the major part of the world's high-grade graphite, are virtually devoid of any manufacturing establishments requiring its use. The industry thus is violently disturbed by wars. Types oF Graphite Used in Crucibles Graphite of various kinds and from many countries has been used for making crucibles. Passau (Bohemian) flake was first used in Europe, but by the middle of the seventeenth century crucible formulas were established largely on Ceylon graphite and German Klingenberg clay. Ceylon graphite is granular and the grains are subdivided into more or less

Jan 1, 1948

By W. L. Fink, M. S. Hunter, R. H. Brown

Early workers attempted to study the structure of alloys by measurement of equilibrium electrode potentials in aqueous solutions containing ions of the metals from which the alloy was made.' The method was subject to such limitations (e.g., the difficulty in attaining electrochemical equilibrium at low temperatures) that it has not been widely used by metallurgists. Recently, Seltz and co-workers have introduced a greatly improved method for studying alloys by measurement of equilibrium electrode potentials in molten salts.2"4 The mathematical treatment is the same, of course, as for equilibrium potentials of amalgams in aqueous solutions.5 This method will probably find extensive use, since it makes possible not only the determination of phase fields of equilibrium diagrams but also the determination of certain thermodynamic quantities which can be used advantageously in metallurgical calculations. However, the method presents difficulties. With many metallic and alloy electrodes, reversibility is not readily obtainable. Also, the difficulty of obtaining suitable material from which to make the cells is increased as the temperature is increased. Moreover, the necessity of carrying out measurements in a vacuum requires additional apparatus and introduces considerable difficulty, especially at the higher temperatures. Apparently, no consideration has been given heretofore to the metallurgical use of irreversible electrode potentials that exist when a specimen is immersed in a suitable aqueous solution at room temperature. The apparatus and the method required for such measurements are very simple, and if the results of such measurements could be demonstrated to be reproducible they might be very valuable in studying the structure of alloys. The method would not have the scope of that developed by Seltz and his co-workers because no thermodynamic quantities could be calculated from the data. However, the utility and the simplicity of the method might warrant extensive use for the determination of phase fields and similar applications. Theory of Irreversible Potentials A brief review of the theory of irreversible potentials will be given before showing how to interpret the potential readings in terms of alloy structure. It is known that heterogeneity of a metal surface in an electrolyte will produce points of different potentials, with the result that current flows between these points and electrochemical reactions occur. The points at which oxidation reactions are localized are known as anodes, and those at which reduction reactions are localized are known as cathodes.6, 7, 8 For the benefit of those who are not familiar with the terms anode and cathode as applied to a primary cell, the potential difference between anode and cathode of such a cell can be measured when

Jan 1, 1941

By McHenry Mosier

MeRcuRy is one of the strategic metals of which the supply has been raised from critical uncertainty to more than enough for essential demands. Work by the Bureau of Mines has contributed substantially to increased production of mercury in the United States and to consequent accumulation of Government stocks. Other contributing factors have been higher prices for mercury and Government loans to operators. The Bureau has undertaken 13 exploration projects, 10 of which have been completed. This work has comprised 28,376 ft. of several types of drilling and 23,798 lin. ft. of surface trenching, and has indicated commercial ore containing 34,800 flasks of mercury and marginal ore containing 26,200 flasks, a total of 61,000 flasks; equivalent, respectively, to domestic production for 8 months, 6 months, and 14 months. As Government stocks are now adequate, domestic production (currently at the rate of 50,000 flasks per year) is gradually being curtailed through Government control of labor and operating supplies. Introduction Mercury was one of the seven metals designated as strategic by the Army and Navy Munitions Board in 1939, when Congress appropriated funds for the investigation of domestic sources of supply of war minerals. The Bureau of Mines immediately started a limited search for strategic minerals, but the first mercury project was not begun until December 1940. The U. S. Geological Survey assisted in the search for cinnabar by contributing information on domestic mercury deposits, preparing maps, and making geological studies of exploration projects. The present high rate of production of mercury in the United States was encouraged by the increase in price to $196 per flask at New York (Fig. I) and Government loans to operators for mine development and plant construction. The Bureau of Mines has issued, for restricted distribution subject to wartime controls, 13 War Minerals Reports on individual mercury deposits (listed in appendix A). In March 1942 it also published a Progress Report of the Metallurgical Division, R. I. 3627, Cinnabar-reduction Plants of the Southwestern Arkansas Quicksilver District. Uses of Mercury Mercury and its compounds have more than 3000 uses. Its principal use is as a catalyst in the manufacture of gases for chemical warfare; the next largest is in pharmaceuticals. Mercury is essential also for: (I) certain electrical apparatus, (2) industrial control instruments at many war plants, (3) munitions, including blasting caps, (4) insecticides in agriculture, (5) antifouling paint for ship bottoms, (6) dental preparations, (7) general laboratory use, and (8) amalgamation of free-milling gold ores.

Jan 1, 1949

I HIT the ceiling when I opened my November MINING ENGINEERING and after waiting a week to cool off I' still find it necessary to express my resentment of the gross libel embodied in the editorial introduction to Norman Stines' legitimate criticism of my paper on "Russia's Mineral Potential" (p. 949). The underlying thesis of my article, and a point that I tried to make even more clearly in my oral presentation at the St. Louis meeting last February, is that we should not over estimate the present and near-future mineral production of the USSR. The words that I resent in your boxed introduction are: "Opinions range from those presented by Paul Tyler ... to those of Norman C. Stines . . ." This is not merely an understatement that can be defended by admitting that the range goes much farther to the left, beyond me. It represents the appraisal that 90 pct of your members will carry away, namely that I am not only an incompetent observer-which may be true-but always that my bias is to applaud the efficiency of the beasts in the Kremlin-which is not true. Notwithstanding my efforts to clarify the record I now find myself branded as being at the opposite pole from 'Mr. Stines among the red-eyed worshipers of Communism or at least among the timid souls that shake in their boots in the belief that the Soviet system has created an invincible as well as an evil menace to the decent peoples of the world. My ideas are somewhere in the middle ground between Mr. Stines' complaisance or contempt and the exaggerated fears of several other observers whose views have received wide acceptance. PAUL M. TYLER MINERAL TECHNOLOGIST & ECONOMIST 5005 EDGEMOOR LANE, BETHESDA, MD. The introductory paragraph to Mr. Stines' criticism of Mr. Tyler's article (Russia's Mineral Potential, June issue MINING ENGINEERING, page 494) is erroneous as pointed out in author Tyler's letter above. In his article he objectively presented an estimate of the mineral position of the Soviet based on the statistics available to him which sources are credited in the first paragraph of his article. We happen to know that, Mr. Tyler was reluctant to prepare the article for the Mineral Economics Division sessions at the 1951 Annual Meeting and did so only because of his loyalty to AIME. It was thought that this article would be a basis for discussion of this important subject at the Annual Meeting. We apologize to Mr. Tyler for any embarrassment our introduction, may have caused him. Editor

Jan 1, 1952

By C. W. Phillips, R. S. Busk

With most cast metals the grain size may vary within wide limits, depending upon the conditions at the moment of freezing. These conditions are subject to control in magnesium-base alloys, by proper melting and superheating techniques, enabling production of quite uniform and fine-grained castings, almost independent of section thickness. However, such variations of grain size as do exist, in common with all metals, are reflected in corresponding changes in mechanical properties. It is the intent of this paper to present data giving the relationship between grain size and mechanical properties. Data are also included on the combined effects of grain size and micro-porosity. In addition, a short discussion of factors influencing the grain size of sand castings is included. Measurement OF Grain Size By grain size is meant the statistical distribution of volumes occupied by the individual crystallites in a metal section. Since this is almost always impossible of direct measurement, several methods of estimating and expressing the size have been evolved. Most exact methods make use of the microscope. This involves study of a single plane cut at random through the metal. What is seen in the microscopc are polygons, each the cross section of a grain. The diameters or areas of these polygons are then measured and the grain size is expressed as an average diameter, number of grains per unit area, average area per grain, or, rarely, average volume per grain. Rutherford, Abom, and Bain3 have discussed extensively the errors involved when using a plane section to estimate volume. They clearly point out that the tendency is to underestimate the true grain size because of the nature of the measurcment. The A.S.T.M. recommends that measurement be made by comparison with a standard chart, by means of Jeffries' planimetric method4 or Heyn's intercept method. The Society recommends that the notation be in terms of the number of grains per unit area (as is the grain-size number used for steel) or as an average diameter, expressed in inches or millimeters (as for copper and brass). The method of measurement used for this study was comparison with a standard chart, which has been described by P. F. George.5 The chart was constructed by photographing at Ioo diameters a uniform specimen with an average grain diameter of 0.003 in. The average diameter of this specimen was determined by numerous measurements, using both the Jeffries and Heyn methods. The other grain sizes were then obtained by appropriate enlargemcnt of the master sample. Careful comparison of the chart method with other methods on identical samples indicates that though the differences be-

Jan 1, 1945

By B. N. Das, H. E. LaBelle, G. A. Wolf

ZnxHg1-xTe and GUPxAS1-x crystals have been grown from solution by a traveling heater method (THM). In a floating zone type fashion a solution zone sandwich of liquidus composition is made to migrate through feed material of solidus composition by a slow-speed movement of <0.25 mm per hr of the total charge through a stationary radiation or rf heater. ZnxHg1-xTe of composition 0 < x < 0.3 and GUPxAS1-x of composition 0.5 < x < 0.7 have thus been grown from their solution in liquid tellurium and gallium, respectively. A simplified analysis of heat and material transport is given. In this method, Proper adjustment of the temperature distribution along the liquid solution zone axis eliminates instability of the crystal growth front and constitutional supercooling. 1) ZnxHg1—xTe: The solid-solution telluride was grown in sealed quartz tubes at a temperature of 500 to 650°C. For first Preparations mechanical mixtures SINGLE crystals of solid solutions of III-V and II-VI compounds have been grown by various techniques from the melt, from the gaseous phase, or from solutions in of ZnTe and HgTe were used. X-ray determinations showed the resulting crystals to be homogeneous throughout their entire length, except for the end sections. The homogeneity is greatly improved by reusing the ingots obtained from first Preparations as feed material in subsequent crystal growth runs. Ingots of up to 4.5 cm have thus been obtained. 2) GaPxAs1-x: Crystals were grown in a EN crucible at a temperature of 1050°C. For first Preparation a mechanical mixture of Gap and GaAs was cemented together by a minimum amount of liquid gallium through "wet" grinding of Gap and GaAs crystals in the liquid metal and subsequent exuding of excess gallium by compacting of the charge in the EN crucible. Electron microprobe measurements using P-Ka and As-Ka radiation showed uniformity over a length of 0.4 cm. Properties of the various Preparations are described. liquid metals.&apos;-&apos; Their growth from the melt by passing a liquid zone of pseudobinary liquidus composition through a solid rod of solidus composition is generally a convenient method of growth of single crystals of solid solutions of homogeneous composition. This method loses much of its usefulness, however, if the melting point or the vapor pressure of the solid solution is high. In the case of a compound having a high melting

Jan 1, 1969