Search Documents

By W. O. Philbrook, R. S. Kaplan

Rates of oxidation were studied for levitation-melted samples of Fe-C, Fe-Si, Fe-C-Si, Fe-C-P, Fe-C-Mn, and Fe-C-S alloys oxidized by mixtures of either 5 or 10 pct O2, in helium at several temperatures in the range 1850o to 2050°C. The concentrations of the oxidized elements decreased linearly with time. Mass transport in the gas phase was found to be the rate-controlling step. Ilowever, a mulliple -film model was necessary to account for the flux of iron and manganese vapor counter to the oxygen flow. THE advent of the basic oxygen and spray-refining processes of steelmaking has generated considerable interest in the kinetics of reactions between oxygen-bearing gases and liquid iron alloys. The object of this research was the determination of the role of mass transport in the gas and metal phases and of surface chemical reactions in the overall oxidation process. Of the reactions for elimination of elements dissolved in liquid iron, the oxidation of carbon has been investigated most extensively. Studies by Fuji and Ura,1 Fuji,' and Gunji et a1.,3 done with pilot-scale basic oxygen furnaces, indicated that mass transport of gaseous oxygen was rate controlling when the metal carbon content was greater than 0.15 to 0.30 pct. When the carbon content was less than this critical amount, diffusion of carbon dissolved in the iron was thought to be rate limiting. L. A. Baker et a1.4,5 levitated samples of iron-carbon alloys and oxidized them in CO-CO2, CO-C02-He, and O2-He atmospheres at 1660°C. These investigators found that the metal carbon concentration decreased linearly with time and their samples exploded when the carbon content fell below about 0.8 pct. They concluded that the rate-limiting step was the transfer of oxidant to the gas-metal interface. A model based on this rate-limiting step predicted decarburization rates within a factor of two of those experimentally observed. The explosion of the samples was attributed to a shift in rate-controlling step from gas-phase mass transport to transport of carbon dissolved in the metal. L. A. Baker and R. G. ward6 and R. Baker7 used freely falling droplets to investigate oxidation kinetics. In both papers, the authors speculated that flame fronts may have been partially responsible for the lack of better agreement between experiment and theory. Swisher and Turkdogan8 oxidized liquid iron having an initial carbon content of 0.97 pct with CO-CO2 and CO-C02-Ar mixtures at 1580°C. They concluded that a surface reaction was the rate controlling step. Iron-silicon alloys have been oxidized by R. Baker7 and Filipov and Martynov.9 R. Baker 7 also studied iron-carbon-silicon alloys falling as liquid droplets through oxygen. He found that the rate of both carbon and silicon oxidation varied inversely with the drop radius. When the initial silicon concentration was greater than 6 pct, the samples cooled during their fall. Manganese oxidation has been studied by R. Baker,7 and by Filipov and Martynov.9 ward10 investigated the loss of manganese from liquid iron under vacuum. He found that mass transport of manganese vapor was rate limiting in argon atmospheres of 0.02 torr to 700 torr pressure. Iron-sulfur alloys were desulfurized with H2-He and H2-Ar mixtures by Peters et al.11 A model based on the transport of H2S from the gas-metal interface into the bulk gas gave fair agreement between the predictions of the model and the experimental results. EXPERIMENTAL TECHNIQUE Essentially, the technique consisted of using helium-oxygen gas mixtures to oxidize levitated samples of liquid binary and ternary iron-base alloys. The fused silica reaction tube is shown in Fig. 1. The coil design is similar to that of L. A. Baker et al.4'5 A Tef-lon-sheathed, ferritic stainless steel lifter (B) and an alumina pedestal (C) were used to support the sample in the coil prior to levitation and for the recovery of the sample. Samples were inserted into

Jan 1, 1970

By D. B. Hunter, H. W. Rosenberg

The titanium-rich portion of the Ti-Pd system was investigated from 0 to 75 wt pct Pd by metallo-graphic and X-ray techniques. A 0 eutectoid occurs at 24 wt pct Pd and 1190°F. Two compoutzds are indicated in the region below 75 wt pct Pd, Ti,Pd and Ti2Pd3. The solubility of palladium its a titanium is low, probably less than 1 pct. In 1960 Rudnitskii and Birunl published a complete version of the Ti-Pd phase diagram. However, their work was in disagreement with the earlier literature in that they reported only one inter metallic compound, whereas three had been reported earlier. In view of these discrepancies, it was therefore necessary to redetermine those portions of the diagram of immediate interest. The following account describes our work on the system over the range of 0 to 75 wt pct Pd. MATERIALS AND METHODS Distilled titanium sponge and elemental palladium were used in the formulation of the alloys; the chemistry of these materials is detailed in Table I. The alloys were prepared as 10 to 50 g blended compacts that were melted into buttons by arc melting under gettered argon on a water-cooled copper hearth. Weighing of the ingredients before and after melting showed that negligible weight changes occurred. Therefore, no analyses were undertaken and the compositions of all alloys are nominal. All alloys were fabricated by hot rolling at 1700°F to 0.070-in.-thick sheet. Scale was removed by sandblasting and pickling in a 5 pct HF-35 pct HNO,, balance H20 solution. For metallographic examination, specimens were mounted after heat treatment transverse to the rolling direction, ground on silicon carbide papers of increasing fineness to 600 grit, and then electro-polished using a solution containing 600 ml me-thanol, 60 ml perchloric acid, 360 ml butyl cello-solve, and 2 ml "Solvent X". Unless otherwise specified, etching of alloys containing up to 42 pct Pd was carried out by swabbing with a 12 pct HN03-1 pct HF aqueous etch where a bright etch was required, or by a 1 pct hydrofluoric in saturated oxalic acid solution where contrast between phases was required. The Ti-52.8 Pd alloy was etched with a solution of 25 ml HF, 40 ml glycerine, 35 ml methanol, and 18 g benzalkonium chloride. For X-ray examination, 1/2-in.-square speci- mens of sheet were mounted flat in a standard 1-in. metallographic mount and ground and polished as above. X-ray diffraction was performed using a Norelco type 12045 Diffractometer, employing CuKa radiation with a nickel filter at 40 kv and 20 ma. Specimens were rotated about the sheet normal during exposure. Although this procedure did not remove the effects of sheet texture from the relative intensities, it had the advantage that oxidation or contaminants entering during preparation of powder samples could not confuse the patterns obtained. RESULTS AND DISCUSSION Fig. 1 illustrates the Ti-Pd phase diagram according to Rudnitskii and Birunl with the work of the present authors superimposed. Both interpretations agree that the system is of the 0 -eutectoid type with an extensive 0-phase field, and that the eutectoid temperature is just below 1200°F. There is also agreement that the solubility of palladium in a titanium is restricted. Our work would indicate that the a solubility of palladium is low, probably less than 1 pct. However, whereas Rudnitskii and Birunl place the eutectoid composition at 41 wt pct Pd, this investigation shows it to be at about 24 wt pct Pd. Moreover, this investigation confirms the existence of compounds at Ti2Pd and Ti2Pd3, whereas Rudnitskii and Birun report only a single Berthol-lide phase covering the TiPd to TiPd, range. Laves et a1.' and Wallbaum, whose work was summarized by Maykuth , reported the existence of Ti2Pd3 and TiPd, in addition to Ti2Pd. More recently, Nevitt and Downe~' have reported the structure of

Jan 1, 1965

By V. F. Hollister

The Queen Charlotte gold deposit (also known as the Specogna, Babe, or Cinola) was discovered in late 1970 by Efrem Specogna and Johnny Trico. They were prospecting along the trace of the Sandspit fault, and they sampled jarositic material that included veins from the fault zone. Their assays included some good gold values. They located the Babe Claims in 1971 and optioned them to Kennco Explorations Ltd. Kennco conducted stream sediment and soil geochem studies, geological mapping and drilling of 55.2 m (181 ft) in two drill holes. Kennco withdrew from the property, and by 1977, Cominco, Placer Development, Silver Standard, and Quintana Minerals had each successively worked on the deposit. Consolidated Cinola Mines bought the claims in 1977 and completed exploration of the deposit ultimately in a joint venture arrangement with Energy Reserves. Energy Reserves entered in late 1979, and by 1983, a total of 200 surface and 12 underground drill holes had been completed, totaling 28 600 m (93,832 ft). In addition, a 461.9 m (1515 ft) adit was driven in the ore body. Reserves published by Cinola aggregate 34 Mt (37 million st) of 1.7 g (0.060 oz) Au per tonne. All industry geologists working in the area agree that the Queen Charlotte gold is an epithermal gold deposit in porous volcaniclastic and clastic rocks that is genetically related to a Miocene-Pliocene rhyolite plug. The geologic description here follows the oral presentation made by G. G. Richards, J. S. Christie, and M. R. Wolfhard at a 1976 CIM meeting. Additional comments by the late C. S. Ney of Kennco Explorations are included with the Richards, Christie, and Wolfhard data to complete the geologic set- ting. The attached reprint by Champigny and Sinclair (1 980) provides additional data on the deposit. The Queen Charlotte (Babe, Specogna, or Cinola) gold deposit is located on Graham Island in the northern Charlotte Islands, at the fault boundary of the Skidegate plateau and the Charlotte lowlands. The Sandspit fault marks the physiographic boundary, and it is intruded by rhyolite porphyry at the deposit. Because displaced geochem anomalies, drain- age patterns, and topography suggest dextral and east side down movement for the fault, exposed east block rocks are younger than rocks west of the fault. The east block, which included the ore deposit, is a lowland largely masked by unconsolidated Pleistocene and Recent clastic rocks. Rocks west of the rhyolite plug, on the Skidegate plateau, are Cretaceous carbonaceous and calcareous shale unconformably overlain by a thin veneer of rhyolite tuff. The deposit is about 100 m (328 ft) above sea level. GEOLOGIC SETTING At the ore deposit, the Sandspit fault is a complex structure. However, lithologies on either side of the fault-controlled rhyolite porphyry plug are distinct. West of the rhyolite, the upper member of the Cretaceous Haida formation shale is the most common rock type. The member is composed of dark grey to black, poorly consolidated, and thinly bedded carbonaceous and calcareous shale. The sequence is silicified to an argillite or a hornfels near the rhyolite. West of the rhyolite porphyry plug, but not importantly involved in the mineralization, is a thin masking cover of rhyolite tuff. The tuff unconformably succeeds the cretaceous shale, but it is largely eroded in the mine area. East of the fault-controlled rhyolite porphyry plug is a thick section of conglomerate and sandstone of the Miocene- Pliocene Skonun formation. The ore body occurs within the coarse clastics, the rhyolite intrusive as the western boundary. Ore is entirely contained within the clastics. Original permeability of the clastic rocks was a major control for ore deposition and alteration, and for that reason, the Skonun formation is described in greater detail. The Skonun formation clastics unconformably overlie Haida shale. The Skonun is at least 300 m (984 ft) thick in the mine area, where it trends northerly and dips easterly 15º to 25º. The sequence is about 62 percent conglomerate, 3 1 percent coarse arkosic sandstone, and 7 percent interbedded siltstone and sandstone. Contacts between adjacent beds are generally sharp. Stratigraphic correlations between drill

Jan 1, 1985

By R. F. Sheldon

The discovery of the Carlin deposit was the result of discriminating geologic research and prospecting devoted to the objective of finding a gold deposit that could be mined by open pit methods. By the late 1950s, Newmont Mining Corp. was becoming increasingly concerned about the trend of rapidly rising underground mining costs unless bulk mining methods could be applied. The desirability of finding an open-pittable gold deposit was apparent. The attention of Newmont geologists was directed to Nevada by the publication of two papers: "Paleozoic rocks in North-central Nevada" (1958) and "Alinements of Mining Districts in North-central Nevada" (1960), both authored or co-authored by Ralph J. Roberts of the United States Geological Survey. John Livermore, geologist of Newmont Exploration Ltd., attended a talk given by Roberts in Ely, Nevada in the summer of 1961. These papers and the address by Roberts gave details concerning the Roberts Mountain overthrust, a 483 km (300-mile) long, shallowdipping fault which pushed clastic and volcanic rocks of early and middle Paleozoic age eastward over younger marine formations. Subsequent uplift and doming with consequent erosion had locally removed the upper plate strata exposing windows of lower plate carbonate rocks. Roberts noted that the principal mineral deposits of the region, including gold, were associated with these windows which exhibited a preferred alinement. In the summer and fall of 1961 Newmont's exploration geologists John Livermore and J. Alan Coope began a systematic examination of gold occurrences associated with these windows, aided by further discussion with geologists of the US Geological Survey. Attention was directed to the Lynn and Carlin windows, particularly to those formations lying immediately above and below the Roberts Mountain fault. It was appreciated at the time that many of the gold occurrences in the region were unusual in that no colours were obtained even when panning high grade samples. A large number of rock samples were collected and analysed using fire assaying procedures, and background values for gold were established. This systematic rock sampling resulted in the identification of a distinct area of anomalous gold values, and a block of claims was staked in late October, 1961. These claims, plus an adjoining optioned 32.4 ha (80 acres) of ground, cover the main area of the present Carlin gold mine. Prior to snowfall that winter, one of the bulldozed assessment pits required to establish a claim's discovery exposed 24 m (80 ft) of mineralization assaying 0.007 kg/t (0.22 oz per st) gold. In the spring of 1962 a program of trenching, sampling, and geological mapping followed by rotary drilling was underway. Other properties in the area were acquired. The generally undistinguished nature of the dolomitic siltstones and silty dolomitic limestones hosting the micron-sized gold particles, coupled with the lack of visually associated guide minerals, made identification of the gold bearing areas very difficult. The entire drill column had to be assayed to ensure that values were not overlooked, as very often sections that might be assumed to be waste turned out to be high grade. On September 10, 1962 a high grade intersection of 24 m (80 ft) assaying over 0.03 kg/t (1 oz per st) gold was encountered in the third hole drilled. An expanded program of both rotary and diamond drilling led to the further delineation of the ore body. By December 1963, the exploration program had established an initial reserve of 10 Mt (11 million st) grading 0.01 kg/t (0.32 oz per st) gold. A 1.8 kt/d (2,000 stpd) processing plant was constructed and the first gold bullion was poured in May, 1965, just two years and eight months after the discovery hole was drilled. REFERENCES Roberts, R.J., Holz, P.E., Gilluly, J., and Ferguson, H.G., 1958, "Paleozoic Rocks in North-central Nevada," Bulletin American Association of Petroleum Geologists, Vol. 42, No. 12. Roberts, R.J., 1960, "Alinements of Mining Districts in North-central Nevada," Professional Paper 400-B, US Geological Survey, Article 9.

Jan 1, 1985

By L. W. Fagg

The purpose of this paper is to present in a convenient form data and examples necessary in making dynamometer card analyses; also to outline a procedure of well weighing. Many articles and papers have been written delving into the mathematical considerations relative to the shape and characteristics of dynamometer cards. However. it is recognized that there are too many unknown factors involved in such calculations to assure a workable degree of accuracy. For this reason the accepted procedure is to take dynamometer cards on wells in question rather than try to calculate the load curve. The polished rod dynamometer is now recognized as a necessary tool for measuring loads, torque, and horsepower. It is also used to determine pump action and trouble-shoot for any seemingly abnormal pumping condition. The apparently infinite variety of a = maximum load (height x scale constant) b = minimum load. Range of load is difference between maximum and minimum load speed—taken with stop watch stroke —measured at polished rod c = beginning of down stroke in direction of arrow. (End of up stroke) d = beginning of up stroke. (End of down stroke). Polished Rod Horsepower = (Area of card) x Scale const. x Stroke x Length x spm (Length of card) 33000x 12 1.35 1.35------x5300x 24 x 12 2.53 --------------------------= 2.06 23000x12 Appraximate Peak Torque: Upstroke = (2390) (12) (1) = 28,700 in. Ib Downstroke = (1 860) (12) (.866) = 19,300 in. Ib Counterbalance should be increased to make up stroke and down stroke peak torque equal. FIG. 1 dynamometer cards that can be obtained is one reason for the general lack of usage of the dynamometer as a control instrument rather than a means for making routine measurements of leads and horsepower. When it is considered that the dynamometer card is a record of the resultant of all forces acting on the polished rod at any particular instant during the pumping stroke. the problem is then one of breaking down this resultant into its various components. As a means of a quick review we shall consider the examples shown in Figs. 1 to 9: and Tables I and II and then proceed to the interpretation of variously shaped cards caused by some abnormal operating condition. In Table 11, when we were considering the factors involved in calculating the peak polished rod load, it can be seen that the factors involved greatly oversimplify the problem. Certain assumptions are made which may or may not he even close to the actual field conditions, such as the specific gravity of the fluid generally considered as one; that the crank has constant angular velocity; that the down-hole friction is zero; and that the fluid lift is from the pump. In the following examples we shall see what a variation in fluid weight and friction can do to the general shape and magnitude of the dynamometer card. (Figs. 10 to 22.) MAKING THE WELL STUDY It is obvious that it would be impractical to consider in detail all of these factors each time a well study is made, inasmuch as each well study job could conceivably be extended into a research project rather than serve the practical requirements of finding the answer to a specific problem. For this reason it is important that some objective be established previous to the time the well study is made. Load at TU = 3070 Ib Crank angle when polished rod is at position TU = ? ? = 30° Maximum counterbalance effect at polished rod = 2760 Ib Torque at TU = (Load at TU — Max. counterbalance effect-lbs) sin 0 x Length of Stroke 2 = (3070-2760) .5 x 24 = 1860 in. 15 2 Torque at TD = (Load at TD — Max. counterbalance effect-lbs) sin ? x Length of Stroke 2 = (530 - 2760) sin 330' x 24 = 13,400 in. Ib 2 Note: sin 0 from c to d on UPSTROKE will be positive value. sin 0 from c to d on DOWNSTROKE will be negative value Torque at c and d is zero because 0 is zero. FIG. 2 —APPROXIMATE METHOD FOR CALCUlATlNG TORQUE

Jan 1, 1950

By Frank C. Kelton

A method is outlined for the analysis of large cores, developed primarily for the purpose of obtaining reliable data on fractured or vugular limestones. Porosity and fluid saturations are determined by a modified Dean-Stark extraction after initially bringing the samples to 100 per cent liquid saturation by a vacuum-pressure method. Horizontal permeabilities on the whole samples are determined in two directions, parallel and perpendicular to the di-rection of principal fracturing. Results are presented for various types of formations. A comparison is made between data obtained by this special method and the method of conventional analysis, and discussion is given of the relative advantages and limitations of each. In view of this comparison a modified method for the analysis of fractured and vugular formations is proposed, which method retains the advantages of the previously outlined techniques but gives promise of speeding up the analysis. INTRODUCTION For many years the greater part of the production in the Permian Basin was from formations of Permian and Pennsylvanian age. While production from these formations is still the predominant production. deeper prospecting has brought to light older formations with oil productive characteristics. Attempts to core these deeper horizons were at first usually characterized by poor recovery. The old rule of thumb, "good core recovery — poor well" was originated and remained in effect until recently. With the advent of diamond coring and the increased efficiency in drilling and coring operations. the old adage has lost its significance. Formations of Devonian. Silurian and Ordo-vician ages were successfully cored with varying degrees of recovery. The cores thus obtained were surprising and in some case; disappointing. Good recovery from these formations led to speculation as to the feasibility of analysis and the meaning of data obtained from conventional analysis. Commercial laboratories were engaged to analyze these cores. and their results indicated that data obtained by conventional methods would be of little value. From visual inspection it was apparent that in many cases the effective porosity for storage of hydrocarbons. and permeability. were contained largely in fractures and solution cavities rather than in the primary crystalline structure of the formation. In other cases the solution cavities augmented the effective porosity of the primary crystalline structure, or fractures enhanced the permeabiilty of the latter so that the formation might respond favorably to acidization and become commercially productive. Since the spacing of the cavities and fractures was often comparable to the core diameter, it was evident that the entire core should he analyzed instead of small fragments. On the basis of these observations, commercial laboratories were requested to devise a system of analysis which would yield data of practical value. Pro- cedures have accordingly been developed which seem to meet this requirement, and to date nearly 12,000 large core samples have been analyzed. It is the purpose of this paper to describe the methods used, to present typical results for several fractured formations and to compare the data obtained by this special analysis with that obtained by conventional analysis. Certain modifications and alternative procedures are finally suggested to speed up the analysis. CORE ANALYSIS PROCEDURE Fluid Saturations and Porosity The core sample, in segments up to 15 in. in length. is marked, weighed and examined under ultra-violet light to determine the presence of oil saturation. If present, the approximate quantity of oil and its location on intercrystalline, fracture or vugular surfaces is noted. This information is carefully recorded. The degree of fracturing and/or vugular development is also noted. The sample is then placed in a pressure cell and the air evacuated with a high speed vacuum pump. This evacuation is continued only long enough to reduce the pressure to approximately the vapor pressure of water in order not to remove excessive amounts of water. Water is admitted to the cell and allowed to penetrate the sample under atmospheric pressure, filling the pore space initially occupied by air and replacing the small amount of water removed by evacuation. Pressure up to 200 psi is applied to force water into the smaller capillaries, and the sample is left sub-

Jan 1, 1950

By R. Bakish, M. A. Badiali, N. W. Kirshenbaum

One pound of ultra pul-e molybdenum has been produced containing both metallic and nonmetallic impuvities close to or less than the limits of detection. various purification methods were investigated; althouglz the use of move than one purification step was consideved, it was found that a single, caefully-controlled sublimation of MoCl5 yielded a highly puvified product without prior treatment or recourse to repeated sublimation. Hydrogen reduction of MoC1, to metal was attempted at atmospheric pressure; however, reduced pressure was necessary to obtain substantial yields. The tubular deposits of metal were consolidated into bulk fovm by electron beam melting undev high vacuum yielding a very low gas content. Boblems involved in monitoring the puvity of these materials and analytical results obtained are also presented. THE pronounced effect of even trace amounts of impurities upon fundamental properties of materials is well known to metallurgists and solid-state physicists. Consequently, groups interested in basic studies of metals have in recent years immensely stimulated the preparation and production of numerous ultra-pure metals. Increased demand by scientists for these high purity materials has necessitated development of facilities to prepare them in significant quantities; the procedures reported here were devised to produce significant quantities of ultra-pure molybdenum. Previous work performed in the field of vapor phase purification and hydrogen reduction of several other refractory metal chlorides had demonstrated valuable techniques applicable to molybdenum.' Various purification and reduction steps were individually investigated. Those procedures which showed the most favorable results with respect both to attainment of high purity and to ease of operation were then incorporated in the process utilized to produce the metal.' STARTING MATERIALS It is well known that because of differences in volatility, chlorides may be separated by fractional distillation. It was presumed that distillation of molybdenum pentachloride offered a simple and straightforward method of purification due to its relatively low boiling point. Alternatively, sublimation of the solid chloride also appeared feasible since MoC15 has both a reasonably narrow temperature range in which it exists as a liquid (a property typical of refractory metal chlorides) and a low enthalpy of sublimation. Pertinent thermochemical data of MoC15 are given in Table I. It should be noted that this compound must be handled with care as it is extremely hygroscopic. Anhydrous MoC15 was obtained from the A Metal Climax Co. METHODS OF PURIFYING MOLYBDENUM PENTACHLORIDE Distillation. It was expected that distillation methods, while affording an efficient purification, would prove simple to control and would have a higher production rate than sublimation processes. Also considered was the possibility of effecting a high degree of purification by using both these volatilization methods in conjunction—possibly a distillation followed by sublimation of the solidified condensate. Distillation of MoC15 was investigated using a single stage distillation column packed with chemically resistant glass beads. Heating coils were wound around the column and collection tube (condenser). As-received MoCl5 was charged into a flask connected with the column using a side loading arm under an argon flow. After the column and condenser were brought to about 270" and 210°C, respectively, the apparatus was lowered until the flask was fully immersed in a constant temperature fused salt bath maintained at about 285 °C. Distillation was continued for about 10 or 15 min until 50 to 70 g of distillate had been collected. Analyses of these distillations indicated that several elements, e.g., Cu, Fe, Ni, Cr, and Mg, were lowered in quantity although not all were removed to the same extent. The occurrence of Na, B, Si, and A1 in the distillates appeared to be due to contamination, possibly from corrosion of the pyrex glass. An improved distillation system of larger capacity and longer distilling column was built. Improvements were effected in lowering the amounts of such impurities as B, Mn, Ni, Na, Mg, Cr, Cu, and Fe. These studies were pursued concomitantly with efforts to purify by sublimation; it was subsequently found that although improvements in purity were obtained by distillation, sublimation processes were simpler to control and effected a high degree of purity.

Jan 1, 1963

By S. Feuerstein, L. Rice

The effect of low pressures on the flow and fracture behavior of molybdenum is described. For poly crystalline samples, room-temperature tensile tests indicate greater ductility under 10 Torr than under intermediate pressures up to and including atmospheric pressure (760 Torr). In addition, tests conducted at 760 Torr under atmospheres of air, dry nitrogen, and purified argon exhibited no apparent difference in mechanical properties. Critical tests involving baking in situ as well as those involving single-crystal deformation further imply that the ductility effect is a pressure-dependent phenomenon related only to the fracture process. This dependency is discussed in terms of adsorption and diffusion contributions. THE effect of very low pressures on material properties has heretofore been presumed to be important only for substances possessing relatively high vapor pressures at ambient temperatures. Research has therefore been concentrated primarily on organic solids and liquids, and in some instances on metals such as zinc and cadmium. Most vacuum-effect studies' on the mechanical behavior of metals have been performed under conditions of either cyclic loading or creep rupture at elevated temperatures, i.e., over extended time periods. These studies were not restricted to high vapor pressure materials but also encompassed such metals as gold, copper, and nickel. Very little concern, however, was placed upon the importance of a vacuum environment on the mechanical behavior of metals subjected to a simple unidirectional deformation at ambient temperatures. A tension test is generally of short duration as compared to a creep test, and at room temperature vacuum effects if any would be expected to be surface-limited. In early 1963, Kramer and podlaseck2 reported a change in the bulk flow behavior of aluminum single crystals during room-temperature tension tests. The deformations were performed under pressure conditions of 760 to 3.4 X 10-8 Torr and indicated for the first time a vacuum surface effect contributing to the bulk tensile behavior of metal specimens. As a consequence, an experimental program was initiated in this Laboratory to study the effects of ultrahigh-vacuum conditions on the mechanical behavior of metals. The results of a preliminary study on poly-crystalline molybdenum3 revealed, unlike Kramer's observations of changes in the stress-strain behavior, only an increased ductility under ultrahigh vacuum. Flow behaviors were nearly identical for all tests re- gardless of pressure. This paper presents comprehensive results obtained in this area of research. 1) EXPERIMENTAL PROCEDURE Three material categories were used in this study: sintered and are-cast polycrystalline molybdenum of nominal purity 99.93+ pct and single-pass electron-beam zone-refined molybdenum single crystals having a nominal purity level of 99.99+ pct. The interstitial levels (weight percent) as determined by the Materials Testing Laboratories, Division of Magnaflux Corp., were as follows: sintered molybdenum (C— 0.005, H—0.0004, O—0.015, N—0.008); and arc-cast molybdenum (C-0.0038, H-0.0003, O-0.015, N-0.023). Single-crystal molybdenum obtained from Materials Research Corp. had a typical interstitial analysis of C-0.0015, H-0.00007, O—0.00045, and N-0.0001. Tensile specimens having a 5 mm diam by 50.8 mm length were prepared from these materials. An average grain diameter of 0.059 mm was obtained for the sintered specimens following a 4-hr, 1600°C heat treatment. Grain sizes from 0.019 to 0.149 mm were obtained in the arc-cast specimens following heat treatments from 1100° to 1600°C for 1 hr. This series of specimens was used exclusively for the grain-size effect studies. All samples were electrolytically polished in 97 pct sulfuric acid solution prior to testing. Experiments were performed at room temperature in an ion-pumped ultrahigh-vacuum system positioned in an Instron tensile machine, Fig. 1. A constant strain rate of 4.2 x 10-4 sec-1 as derived from crosshead displacement was assumed for the deformations. Starting vacuums ranged from 2 to 0.5 X 10-10 Torr. These pressure measurements were made using corrected values4 of an NRC Redhead gage. Comparative readings were also made against a G.E. triggered dis-

Jan 1, 1967

By C. E. Hottman, R. K. Johnson

Fluid pressure within the pore space of shales can be determined by using data obtained from both acoustic and resistivity logs. The method involves establishing relationships between the common logarithm of shale transit time or shale resistivity and depth for hydrostatic-pres-sure formations. On a plot of transit time vs depth, a linear relationship is generally observed, whereas on a plot of resistivity vs depth, a nonlinear trend exists. Divergence of observed transit time or resistivity values from those obtained from established normal compaction trends rinder hydrostatic pressure conditions is a measure of the pore fluid pressure in the shale and, thus, in adjacent isolated permeable formations. This relationship has been empirically established with actual pressure measurements in adjacent permeable formations. The use of these data and this method permits the interpretation of fluid pres.rure from acoustic and resistivity measurements with an accuracy of approximately 0.04 psilft, or about 400 psi at 10,000 ft. The standard deviation for the resistivity method is 0.022 psi/ft, and for the acoustic method 0.020 psi/ft. Knowledge of the first occurrence of overpressures, and of the precise pressure-depth relationship in a geologic province, enab1es improvements in drilling techniques, casing progroms, completion methods and reservoir evalzmtions. INTRODUCTION CENKRAL STATEMENT Operators engaged in the search for and production of hydrocarbon reserves in Tertiary basins are more and more frequently confronted with complications associated with over pressured (abnormally high fluid pressure) formations. This is particularly true in the Texas-Louisiana Gulf Coast area. The problems associated with these formations are of direct concern to the combined activities of all phases of operations, i.e., geophysical, drilling, geological and petroleum engineering.' - Knowledge of the pressure distribution of a given area of operations would greatly reduce the magnitude of many of these complexities and in some cases would completely eliminate specific problems. his pape; presents techniques developed for estimating formation pressures from interpretations of acoustic and electric log data. Specifically: the acoustical and electrical properties of shales, reflected by conventional acoustic and electrical surveys, can be used to infer certain reservoir properties, such as formation pressure, at any level in a well. It has been possible to develop these techniques because of a firm understanding of the basic principles that govern and apply to such overpressured provinces. NORMAL PRESSUKES Normal pressures refer to formation pressures which are approximately equal to the hydrostatic head of a column of water of equal depth. If the formations were opened to the atmosphere, a column of water from the ground surface to the subsurface formation depth would balance the formation pressure. On the Gulf Coast, the shallow, predominantly sand formations contain fluids which are under hydrostatic pressure. These formations are said to be normally pressured or to have a normal pressure gradient.* Experience has shown that the normal pressure gradient on the Gulf Coast is approximately 0.465 psi/ft of depth. OVERPRESSURES Formations with pressures higher than hydrostatic are encountered at varying depths in many areas. These formations are referred to as being abnormally pressured, abnormally high pressured, or overpressured. Formation pressures up to twice the hydrostatic pressure have been observed. These formations require extreme care and much expense to drill and to exploit. COMPACTION-FLUID PRESSURE RELATIONS THEORY The generation of overpressured formations in Tertiary sections of the Gulf Coast and several other Tertiary sedimentary basins is, in general terms, considered to be primarily the result of compaction phenomena.' This portion of the paper presents a brief review of the theory which associates compaction and fluid pressure relations, and should thus provide the necessary background for an understanding of the techniques presented. See Hubbert and Rubey' for a more comprehensive treatment of this subject. The theory of the consolidation of a water-saturated clay' has been well established by workers in soil mechanics. The concept is explained by a model with perforated metal plates separated by metal springs and water and enclosed in a cylindrical tube. Fig. 1 is a schematic representation of such a model (see Ref. 5, Fig. 27, page 74). The springs simulate communication between clay particles, and the plates simulate the clay particles. Mano-

Jan 1, 1966

By J. W. Freeman, E. E. Reynolds, A. E. White

Fram a study of 63 systematic alloy modifications it was found that molybdenum, tungsten, and columbium, added individually or simultaneously, and increases in chromium cause major improvements in 1200°F rupture strengths of Cr-Ni-Co-Fe base alloys. Rupture strengths were a function of the effect of composition modifications on both the inherent creep resistance and the amount of deformation the alloy would tolerate before fracture. THIS paper describes the results of an investigation of a series of alloys with systematic variations of the chemical composition of the following basic alloy: C, 0.15: Mn, 1.7; Si, 0.5; Cr, 20.0; NI, 20.0: Co, 20.0: Mo, 3.0; W, 2.0; Cb, 1.0; N, 0.12; Fe, 32.0 pct. The 62 modifications of this alloy were produced under conditions which minimized all factors influencing properties at high temperatures except composition. Melting, fabrication, and heat treatment were carefully maintained constant. Stress-rupture properties at 1200°F were used as the primary criteria of evaluation of the alloy. The objective of the study was to obtain data for determining the fundamental role of the influence of alloying elements on properties of heat-resistant alloys at high temperatures. In addition the results should be useful in determining optimum chemical compositions, the sensitivity of properties to variations in composition, and the degree to which alloy content could be reduced while retaining worthwhile properties. It is difficult or impossible to develop correlations between properties at high temperatures and systematic variations in chemical composition from published data for wrought heat-resistant alloys developed for gas turbines.' ' The main reason for this is the extreme dependence of the properties on conditions of treatment of the alloys." In most cases variation in final treatments between alloys so influences the properties that the influence of chemical composition is obscured. In addition it is recognized Table I. Basic Alloy and Some Modifications Used Basic AllOy, Variations in Element Pct Composition, Pct C 0.15 0.08. 0.40. 0.60 Mn 1.1 0.03,0.25.0.50,1.0,2.5 S1 0.50 1.2, 1.6 Cr 20.0 10, 30 Ni 20.0 0, 10,30 Co 20.0 0. 10, 30 MO 3.0 0. 1.2.3, 5, 7 W 2.0 0, 1, 5, 1 Cb 1.0 0.2,4,6 N 0.12 0.004, 0.08, 0.18 Fe 32.0 that variations exist between heats of the same alloy which are related to melting practice and that there is a strong possibility that conditions of hot working influence response to final treatments. The development of heat-resistant alloys has been based on the gradual accumulation of data roughly related to composition from extensive testing programs. There is every reason to believe that in most cases the optimum compositions have been achieved by this procedure in the alloys commercially available. There are, however, very little data showing the influence of systematic variations of composition free from the influence of other factors, particularly for alloys of the type investigated. Several investigators of cast alloys have demonstrated compositional effects, notably Grant,1-6 Epremian,t Guy,8 and Harder and Gow.9 Sykes10 eviewed the work on the wrought alloy Rex 78 and the systematic variations of carbon, copper, molybdenum, and cobalt leading to the development of the stronger Rex 337A alloy. From the papers by Wilson11 and Henry12 it is possible to deduce the beneficial effect of substituting cobalt for iron in 0.45 pct C-20 pct Cr-20 pct Ni-4 pct Mo-4 pct W- 4 pct Cb alloys. Wilson mentioned but did not present the extensive compositional studies involved in developing these alloys. Binder" showed optimum properties for 3, 2, and I pct, respectively, for molybdenum, tungsten, and columbium in 20 pct Cr-20 pct Ni-20 pct Co-30 pct Fe alloys for limited systematic variations of these

Jan 1, 1953

By A. S. Odeh

This paper analyzes the effect of limited entry to flow at the wellbore on the steady-state productivity of a well. Wells that have been opened to flow along a fraction of their productive interval are termed wells with limited entry. Previous work treated the cases of a partially penetrating well, a well producing from the central portion of the productive interval and a well in which several intervals equally spaced were open to flow. In this paper the open interval can be located anywhere within the productive interval. Thus, in a sense, it generalizes previous work. The finite cosine transform was used to arrive at a solution for steady-state flow of a slightly compressible fluid. The solution was programmed for a CDC 1604 computer. Numerical vaIues for rd = 660 ft, r, = 1/4 ft, and range of sand thickness of 20 to 200 ft are presented in graphical form. The effect of rd and r, values on the result is shown in a table. The correct calculation of skin and damage ratio in the presence of limited entry to flow is explained and illustrated by examples. Moreover, the paper shows how to calculate the net decrease in productivity due to the combined effect of limited entry and perforations. INTRODUCTION In some wells only a fraction of the productive interval is open to flow. Location of this fraction is usually dictated by formation characteristics and reservoir behavior. For instance, if a gas cap exists, the open interval is located away from the gas-oil contact to prevent any possible gas coning. Wells that intentionally have been opened to flow along a fraction of their productive formation are tened wells with limited entry. Obviously, unintentional completions of this type also exist. Limited entry to flow decreases well productivity. Magnitude of the loss depends on the fraction of the formation open to flow, on the thickness of the sand, on the location of the open interval and on the ratio of rd /r, where r , is well radius and rd is the drainage radius of the well. The use of pressure buildup data on producing wells to calculate the condition of the formation around the wellbore is an accepted practice. van Everdingenl and Hurst2 introduced the concept of she skin factor s considered to be due to a thin layer of different permeability immediately around the wellbore. These authors dealt with the case of a well of complete radial geometry, i.e., a well with open-hole completion that completely penetrates the formation. The presence of a low-permeability skin results in a loss of productivity, as does limited entry. Therefore, if pressure buildup data obtained on a well with limited entry are used to establish the presence or absence of skin (i.e., formation damage), and a correction is not made for this loss of productivity, the calculations would result in an erroneous skin value. They might indicate the presence of formation damage when in reality there is none, or they might indicate a value larger than the true value. This could lead to an incorrect basis for planning remedial measures. Muskat3 studied the problem of partially penetrating wells for the case of incompressible flow. He presented equations and figures which allow estimation of loss in productivity. Brons and Marting,4 using equations based on Nisle's work,5 studied the loss of productivity for three cases. The first was for a partially penetrating well; the second was for a well producing from only the central portion of a productive interval; and the third was for a well in which several intervals equally spaced were open to flow. Their work was for steady-state depletion-type reservoirs wherein the well radius of drainage is established and the fluid is considered to be slightly compressible. Considered in this paper is the problem of wells with limited entry in which the open intervals are located anywhere within the productive sand. The finite cosine transform is used to arrive at a

Jan 1, 1969

By F. G. Miller

Earlier studies of the mechanism of flotation showed that coal flotation products are contaminated by composite coal and mineral particles. The mineral matter of these particles has the dual effect of increasing the specific gravity and decreasing the coal surface of the particle available for bubble attachment. The present study showed that these particles are more loosely held in the froth column than the high grade coal particles, especially in the coarser sizes. Consequently, it is possible in the laboratory to produce a secondary concentration of the product by sprinkling the froth product with water to wash these loosely held particles from the froth during formation and recovery. To improve coal flotation, Bethlehem Steel Corp.'s research department has been working on a number of related problems based on both physical and chemical factors. The ideal is of course full understanding of the interrelated effects of both sets of factors. However, detailed studies1 of each physical factor have produced immediately usable results in commercial coal flotation and are providing the basis for our current work on the effect of chemical factors. Since these detailed studies provided the basis for the present investigation of froth sprinkling, their key results are highlighted here. For example, for a highly floatable bituminous coal, particle floatability was shown to be directly related to the percentage of coal surface available for bubble attachment and inversely related to particle mass. The data also underscored that in a given size range the addition of mineral matter to a particle makes flotation more difficult both by adding to the mass of the particle and by decreasing the amount of coal surface available for bubble attachment. Size also affects particle floatability in that as the size of particles of a given specific gravity increases, mass increases and the ratio between coal surface area and mass of the particle decreases. Flotation tests showed that any recovery of the coarsest particles in a coal feed is accompanied by progressively higher recovery of finer and finer particles. Consequently, fine high-specific-gravity particles are recovered with the coarse good coal. As a result, when the entire 14 mesh x 0 size range is processed by froth flotation, the good coarse coal is contaminated with high-specific-gravity fines. It is the small quantities of these fines that must be rejected from the froth product if flotation efficiency is to be increased above its present level. These principles and findings, together with work by Professor V. I. Klassen,' led to the froth sprinkling investigation reported in this paper. Working with Russian coals, Klassen had shown that froth sprinkling washes loosely held refuse particles from the froth and compensates for the water lost in the upper froth layers and increases its stability. As a result, the coal particles are retained in the froth and the loss of coarse coal from the froth is prevented. Decreases in ash of 0.1% to 1.5% were reported by Klassen. Working with a 28 mesh x 0 American coal, the author of the present paper found that single-stage flotation coupled with froth sprinkling produced a product comparable to that obtained by the more expensive method of roughing and cleaning.3 The investigation reported in the present paper expanded study of the effect of froth sprinkling to include each of the standard size fractions of a bituminous coal. The main findings are as follows: (1) For those size fractions between 48 mesh and 150 mesh, froth sprinkling produces a marked reduction in both sulfur and ash. In the case of those sizes coarser than 48 mesh, while this reduction is not as significant, the additional benefit of shorter retention time is still a plus for froth sprinkling. Furthermore, when froth sprinkling is coupled with normal fast flotation, the product purity approaches that obtained by starvation reagent feeding, i.e., gradual feeding of flotation reagent to float the recoverable coal from the pulp slowly in several increments. The specific results for these two size groups are: (a) 14 x 48 Mesh. By using froth sprinkling with fast flotation, product sulfur can be reduced to a level

Jan 1, 1970

By N. Plint, E. T. Pinkney

Copper segregation developments within the Anglo American Group are described with particular reference to the work of the TORCO Project Team. Some radical differences have been adopted in the mechan-ical approach as compared with methods used by previous workers. Most important among these are the following: (1) The heating unit is a fluidized-bed roaster. (2) A moving bed segregation chamber is used in which a packed bed of heated ore, to which reagents have been added, moves slowly downwards under gravity and is discharged at a controlled rate by means of a suitable valve mechanism. (3) The quantities of reagents used (sodium chloride and some form of carbon) are only a small fraction of those recommended by other investigators. (4) Retention times of only 2 min have been satisfactory for the complete segregation of many types of ore. Project TORCO is the code name given by Anglo American Corp. of South Africa, Ltd., to the investigation undertaken in Zambia to develop a plant capable of treating large tonnages of refractory copper-bearing ores by the segregation process. The process has now been under investigation for six years (1960-66) and during that period work has progressed from bench-scale laboratory tests through small-scale pilot-plant work to a 500-tpd commercial pilot unit. Test work has been carried out mainly on the ores of the Zambian Copperbelt and results have been encouraging. Recoveries on the order of 90% have been obtained on all Copperbelt ores tested with high concentrate grades. PRELIMINARY INVESTIGATION Laboratory scale segregation test work on Nchanga banded sandstone ore and oxidized ore from Kansan-shi was originally conducted by Professor Maurice Rey. SociCtC Miniere et Mktallurgique de Pefiarroya, in 1957. Both ores responded favorably to the process. In November, 1960, the consulting engineers of Anglo American Corp. of South Africa, Ltd., initiated preliminary investigations on the application of the segregation process to Copperbelt ores. In early laboratory work, samples were heated in a closed, externally heated tube furnace for one hour at temperatures ranging from 800 to 830°C. The free moisture content of the ore feed was 4% and reagent additions were 0.5% salt and 1.0% coal. Both salt and coal were pre-crushed to -48 mesh Tyler.* All samples except an ore from the Bancroft mine responded well to the process and recoveries of over 90% were obtained. The presence of dolomite was responsible for the relatively poor recoveries from the Bancroft ore, as tests on one of the other ores with additions of calcite or dolomite confirmed. Recoveries dropped from 94 to 45% Grades of all the rougher flotation concentrates produced were low at 10-15% copper. The laboratory investigation was then followed up on a pilot-plant scale. An attempt was made to carry out the segregation process in a coal-fired 5-ft-diam fluidized-bed roaster. The feed consisted of a banded sandstone from Nchanga to which 0.5% sodium chloride had been added. Reducing conditions were maintained in the roaster by the addition of coal in excess of that required for heating the feed. The excess coal and added salt constituted the segregation reagents and the temperature of the bed was held at approximately 750°C. Recoveries of copper and grades of concentrates were low. The reasons for lack of success were: (1) The reaction is a gaseous one and a fluidized-bed roaster is therefore unsuitable as a segregation unit. (2) Coal in excess of that required for heating was introduced into the fluidized bed and under these conditions some of the copper would be reduced in situ. The term "reduced in situ" is used here to describe any copper mineral reduced to the metallic state in its original site within the ore particles. If this copper is to be recovered by subsequent froth flotation it must first be liberated from the gangue by grinding or some other method which, in practice, is usually not feasible on ores of this type.

Jan 1, 1969

By E. M. Norris

THE Western phosphate deposits extend over a large area in the Rocky Mountain region, comprising portions of south central Montana, southeastern Idaho, northeastern Utah, and southwestern Wyoming. A limited acreage of these deposits passed into private ownership prior to Dec. 9, 1908, at which time 7000 sq. mi. of land in these phosphate fields was withdrawn from public entry by direction of the Secretary of the Interior. Under the Act of Feb. 25, 1920 (41 Stat. 437) title to all phosphate lands in the public domain was reserved to the United States with provisions for leasing portions to citizens, corporations, states, etc. The above act, in effect, created by law a Western phosphate reserve of approximately 2,269,055 acres.

Jan 1, 1944

By AIME AIME

FRANK T. SISCO is a native of Lawrence, Kansas. He received his earlier education in Clinton, Iowa and his university training at the University of Illinois. His experience in the steel industry has included service in the chemical, testing, and metallurgical departments of the Illinois Steel Co., of South Chicago; the Hess Steel Corp., of Baltimore; the IJ. S. Naval Ordnance Plant at Charleston, W. Va.; and the American Steel and Wire Co., Waukegan, Ill. He severed for seven years as chief of the metallurgical laboratories of the U. S. Army Air Corps at Wright Field, Dayton, before coming to New York in 1930 to become metallurgist and editor of the Alloys of Iron Research, the position he now holds.

Jan 1, 1940

By AIME AIME

M ALBERTSON is research engineer for the Shell Petroleum COT. He joined the Roxana Petroleum Corp. (later the Shell) in 1920, at Hanger, Texas, became district geologist at Shreveport, and after two years was transferred to the production department, where he has been for the past fifteen years. His jobs have ranged from a modest field engineer up to assistant production manager. During this time hc has successively resided in Texas, Louisiana, Missouri, Louisiana, Oklahoma, Missouri, Texas, The Hague (Holland), and Texas. II? the Yates Pool, Texas, in 1929, "Al" initiated' the tubing of wells under pressure to control gas-oil ratios, particularly at restricted rates of flow. This led to the compulsory tubing of all oil wells drilled in the State

Jan 1, 1937

By AIME AIME

FIFTY years ago William Bertolette Plank was born in Pennsylvania, in which state he was also educated, winding up with an E.M. from Penn State in 1909, at the age of 23. ' He remained there as instructor for a year, and then went with the Philadelphia & Reading Coal & Iron Co. as mining engineer for three years. During the next four years he was on the staff of the Pittsburgh Coal Co. In 1916 he turned to Government work, going to Pittsburgh as junior mining engineer for the U. S. Bureau of Mines. He became successively assistant mining engineer there, mining engineer at the Bureau's Urbana, Ill., station, and finally Mr. Plank was appointed district mining engineer for the Bureau at Birmingham, Alabama.

Jan 1, 1937

By AIME AIME

LEWIS EMANUEL YOUNG was elected a Director of the A.I.M.E. at the last Annual Meeting as a representative of District '4, including. Ohio, West Virginia, and western. Pennsylvania and New York. He also represents the Coal Division, in which industry lie has actively participated- for nearly twenty years. Dr. Young was horn in Topeka, Kan., Oct. 1, 1873, received mining degrees from Penn State and ,-Iowa. State, and a Ph.D., from Illinois. The first part of his professional life was spent in teaching first as instructor in mining at Iowa State, second .as professor of mining at the Colorado School' of Mines, third as director of the School of Mines and Metallurgy at Rolla, Mo., and finally he taught business

Jan 1, 1937

By Robert Palmer

So MUCH has already been written on this vast subject of ground movement and subsidence, and so many data collected and commented upon, that in this paper the author proposes to confine himself to the submission of some plans showing what has actually occurred in the mining of several of the orebodies which have, come under his direction during the last 20 years or so at Rio Tinto, Spain. Some notes are added for the purpose of describing the plans. The author does not attempt to give his opinion as to the reasons why the subsidences have occurred in the manner in which they are found, but confines himself to giving as true a picture as possible of the movements that have taken place.

Jan 1, 1930

By C. F. Jr. Nagel

THIS paper is written primarily for those who are familiar with the processes mentioned but who desire a further insight into some of the fundamental principles. It does not give a complete description of the various practices employed in the working of aluminum and its alloys, but presents a few illustrations of the essential respects in which aluminum differs from other common metals, and emphasizes the controlling factors of the processes under consideration. HEAT TREATING Certain aluminum alloys are capable of having their mechanical properties greatly altered by a heat-treatment process. The degree of this improvement may be illustrated by the typical properties of duralumin (Table 1). It is essential that the material be in the wrought condition in order to obtain maximum heat-treatment effects.

Jan 1, 1927