Search Documents

By Peter J. Szabo

Introduction This is the Pacific Rim. Nearly three fourths of the world's population live on or near its border. In the recent past, on any given day, one could find traversing its„ borders pirates, smugglers, gunrunners, missionaries, slave traders, tourists, and businessmen. If one were not too observant, he would notice that over the last several years the ocean traffic in the Rim has pretty much stayed the same--Polynesian outriggers, passenger ships, general cargo vessels, ore carriers, and oil tankers. If he were to look a little closer, he would notice some coal colliers. A still closer look would reveal that most of them were hauling metallurgical coal destined for the steel mills of Japan, Taiwan, or Korea. If his senses were keen, he would observe that not only were the number of colliers increasing dramatically, but also that a relatively new cargo was being carried to those countries as well as additional areas in the Pacific Rim., This new cargo thermal coal holds the promise of not only exceeding the metallurgical coal trade, but significantly cutting into and decreasing the already vast oil tanker business throughout the Pacific Rim. The high price of crude oil as a result of the oil embargo in the Middle East in 1973-74 has forced the Pacific Rim countries to convert to coal, and as a result, the coal resources of the Rim are being exploited at an ever-increasing rate. Although coal produced outside the Pacific Rim does enter its borders for ultimate consumption from such places as South Africa and the East Coast of the United States, the vast majority of thermal coal that will enter this booming market place will be sourced from countries within the Pacific Rim. Accordingly, this paper will provide an overview of those sources with particular emphasis on the non-communist block nations. This is not to say that countries such as China and Russia will not be players in the Pacific Rim thermal coal arena, but that -most consuming countries in the Rim are basing the majority of their near-term sourcing requirements from countries that provide a stable source of supply. Pacific Rim Coal Resources Figure 1 is a map of the Pacific Rim countries and identification of major coal resource locations within its border. Going in a clockwise direction, the following countries will be the major suppliers of thermal coal through the year 2000: Australia, Indonesia, China, Russia, Alaska (U.S.), Canada, United States (Utah, Colorado, Wyoming, Montana), and Colombia, South America. Other countries such as New Zealand, Malaysia, Philippines, Korea, etc., will play a role in supply, but compared to the ones previously mentioned, will only have a minor impact. When one looks at the vast stretch of ocean that separates the sourcing countries from the consuming countries (Japan, Korea, Taiwan, Hong Kong, Singapore, etc.), one realizes that costs of transportation will play a significant role in determining which countries and in what quantities coal will be purchased. Figure 2 for comparative purposes, shows

Jan 1, 1982

By J. Leja, A. Pomianowski

This paper deals with equimolar solutions of xanthate and alkyl trimethyl ammonium bromide adsorption on copper, nickel and sphalerite powders. After an exposition of the experimental methods used and the results obtained, a thorough discussion leads to the conclusion that some molecular association between xanthates and CnTAB's does take place in the bulk of the solution as well as at the air/liquid interface. A spectrophotometric study of xanthate solutions alone and their mixtures with equimolar amounts of alkyl trimethyl ammonium bromide (CnTAB) has established the additivity of ultraviolet spectra (190 to 400 mµ) for potassium ethyl xanthate (KEtX) and C12TAB. No obvious effect of C12TAB addition on the decomposition rate of KEtX was observed, the half life of which was established as 29±3 days at 22°C and pH ~ 6. In mixed solutions of longer xanthate homologues (e.g. hexyl and nonyl) and equimolar CnTAB, colloidal precipitates are gradually formed which contain primarily the corresponding xanthate molecules. The kinetics of collector abstraction by copper, nickel and sphalerite powders were studied in 10-5 to 10"3 M solutions of KEtX alone and in equimolar mixtures of KEtX and CI2TAB. Presence of C12TAB caused a two to three fold increase in the amounts of xanthate (equivalent to many monolayers) abstracted by copper and nickel powders (and in their rates of abstraction) but had no effect on the abstraction of xanthate by unactivated sphalerite (equivalent to less than a monolayer). The adsorption of C12TAB itself from the mixed solutions was very low, at most one monolayer only, and was not influenced by the nature of the solid powder used. A change in the rates of abstraction, observed with copper powder, was interpreted as a completion of a multilayer coating (completely enveloping the grains of powder) following which the rate of reaction between solution and substrate becomes controlled by diffusion through this coating. Work of Buckenham and Schulmanl on molecular associations between different collectors has shown unusual synergistic effects in flotation of individual minerals using mixtures of xanthates and alkyl trimethyl ammonium bromides. The objectives of the present work were: 1) to determine whether these molecular associations between the two types of collectors (indicated by strong surface tension lowering in Buckenham and Schulman's work) take place at the air/liquid interface only or in the bulk of solution as well 2) to establish whether different solids adsorb any species from the mixture of these amphipatic molecules preferentially or as molecular complexes 3) to establish whether there are any differences in the kinetics of adsorption. Metallic copper and sphalerite powder were chosen as adsorbents since they represent two extremes since copper readily adsorbs multilayers of xanthate (and is easily floated with ethyl xanthate) while unactivated sphalerite does not appreciably adsorb xanthate but is known to be readily floated by the amine type collectors. Metallic nickel was included because the infrared spectroscopic work2 on xanthate

Jan 1, 1964

By E. Parthe, J. P. Pemsler

TWO references can be found in the literature concerning the ternary system uranium-tantalum -carbon. C. H. Schramm, P. Gordon, and A. R. Kaufmam reported in this Journal1 on the existence of the ternary carbide "UTa10C4." They also report a second face-centered-cubic carbide phase in the system U-Ta-C, which they denote as "white" phase. The publication includes a reproduction of a Debye-Scherrer powder photograph of "UTa10C4" and a list of the sin2 0 values of this compound. H. Nowotny, R. Kieffer, F. Benesovsky, and E. Laube2 report the complete solid solubility between TaC and UC with a B1 structure. Since the ternary phase "UTa10C4" lies very close to the binary system Ta-C, and the established phase Ta2C with a C27 structure had not been mentioned by Schramm et al., it was thought worthwhile to compare the patterns of "UTa10C4" with Ta2C. The strong lines of the given pattern were indexed on a hexagonal unit cell with the approximate cell parameters a = 3.09A and c = 4.93A. These are the values reported for Ta2C in the literature.3 The correspondence between reported and calculated sin2 8 values may be studied in columns 4 and 5 of Table I. The agreement is fair, but there remain weak lines which cannot be assigned to the hexagonal unit cell. The extinctions correspond to those of Ta2C, but a comparison of the calculated and observed intensities of the Ta2C lines (columns 2 and 3) with those of the corresponding lines of "UTa10C4" (column 6) show occasional deviations. To clarify this situation, four new samples were prepared. The compositions of these samples were chosen in such a way as to observe any existing ternary phase in the system TaC-UC-U-Ta. The samples were arc melted in an inert atmosphere and annealed at 1100°C for 36 to 72 hr. Compositions of the samples determined by chemical analysis are given along with the results of X-ray investigations in Table 11. The following conclusions may be drawn from these data: a) No ternary compounds occur in the section TaC-UC-U-Ta of the ternary system Ta-U-C. The "white" phase reported by Schramm et al. corresponds to a solid solution between TaC and UC. Only one three-phase field exists: C27-B1-A2. (Both tantalum and ? uranium have body-centered-cubic A2 structures.) The a uranium observed in sample 4 transformed from the high-temperature ? phase on cooling. b) The phase Ta2C with a C27 structure extends into the ternary system. "UTa10C4" is, therefore, a uranium-enriched Ta2C. Good agreement is ob-

Jan 1, 1960

By E. W. Gieseke

Coal preparation men today are confronted with problems brought about by changing feed characteristics. The size consist of the coal going to preparation plants has been getting finer and finer. In order to handle these sizes economically, operators are turning to Notation. American Cyanamid Co., in an effort to enable coal flotation plants to produce efficiently at maximum quality and capacity, wnducted experiments which demonstrated that synthetic flocculants are useful for increasing the capacity of coal and refuse filters and for clarifying coal and refuse slurries, and a wetting agent is beneficial in reducing the moisture content of filter cake. Coal preparation men are today confronted with problems brought about by the changing coal markets, changing feed characteristics, and ever increasing labor and supply costs. Small mines are finding it difficult to exist, and the larger mines are rapidly converting to fully mechanized and automated operation to survive. The size consist of the coal going to preparation plants has been getting finer and finer, and the problems facing the preparation plant personnel are growing larger and larger. Facilities can be provided to handle this plant feed in new plants, but the problems are generally not so simple in existing plants where equipment must often be used to perform tasks far beyond its rated capacity. In addition, various state conservation departments, water commission boards, and other Federal and state agencies are endeavoring to eliminate stream pollution. These problems, and many more not mentioned, have been forced on the preparation engineer for reasons of economy and the public interest. In the matter of stream pollution, a determined effort is being made by the coal industry to cooperate with the Federal, state, and local agencies. Economists predict it will be necessary to produce 600 million to 700 million tons of coal by 1970. Bear in mind that the greater proportion of this increased tonnage will have to be processed in existing plants, and you get an idea as to the problems facing the preparation engineer. Methods presently in use for preparing fine coal do an acceptable job down to 48 to 100 mesh. A very large percentage of the - 48 or -100 mesh fraction of the tonnage of coal produced now is being sent to settling ponds or sold at a low figure for reason of quality. This has caused operators to turn to flotation. Building settling ponds and impounding fines is a costly and, at times, impossible method of handling these sizes. Recently a number of flotation plants have been installed to beneficiate material finer than 48 mesh, and these plants have demonstrated that flotation can be successful and increase the plant realization. Coal is a low cost commodity and processes for its beneficiation must be low in cost. Flotation is such a process. It is easily adapted to handling fine coal, requires very little supervision when properly installed, and is economical to operate. Flotation separates coal from refuse and fine clay. For reagents, several combinations are used. Some

Jan 1, 1962

By H. R. Banks

Pondering the action of a ball mill employed to carry on comminution from the product of fine crushing to the point where flotation, cyanidation or other concentrating methods are applicable, one wonders where this machine had its origin. When Henry Wadsworth Longfellow reiterated the observation of that older poet Von Logau, and wrote "Tho' the mills of God grind slowly, yet they grind exceeding small," he probably visualized the type of mill that was employed in medieval times for the production of flour, and can therefore not be considered as having gained admittance to the fraternity of millmen, on behalf of either poet. He does, however, make it quite clear that the efficiency of even these Mills of Destiny was low, and to that extent voices a characteristic of fine-grinding equipment that has been the bugbear of all metallurgical engineers. Principle of Ball Mill The principle of the ball mill probably is traceable to the action along the coast line of oceans or lakes, or in the mountain streams. Wave action on rocks and pebbles, close to the shore line, gives the potential energy to the grinding media, which, in their rolling and tossing, break down the sands, and the resultant "pulp" carried out from the shore is classified and settles out in sizes ranging downward to extremely he mesh. Surely, these are the real mills of God. If we allow our minds to dwell on the total tonnage that has been handled in this way, adding to the sands and clays at present in existence those enormous tonnages of metamorphosed sedimentaries we sense the vast quantity of rock that has been so reduced. Is it not likely, therefore, that the answer to the beginnings of pebble milling, and eventually ball milling, came through the perception of this natural mill by one of our engineering forebears? Methods of Grinding The relatively low return of mechanical input to a ball mill, in terms of useful work accomplished, has always intrigued me immensely. The potential energy absorbed by a ball raised to a high point in its path is apparently released with a very small return in useful work. Is the ball mill the most desirable means of he grinding, or is there some other method through which we can recover a reasonable amount of the energy input in terms of useful work? Some years ago, on his retirement, H. W. Hardinge was questioned as to his thoughts on the trend of fine-grinding equipment. As I recall, his prophecy at that time was that the most likely field for improvement in grinding media would be toward a charge of flat disks with some mechanical scheme to cause them to slide over each other. Undoubtedly, Mr. Hardinge went through the usual experience of the muller and bucking board, the customary introduction of the budding millman to his calling. I have often wondered, but have never got beyond the wondering stage, as to the

Jan 1, 1947

By James R. I. Henagan, William O. Crego

The Mamou Field, located in Evangeline Parish, La., is an elongated anticlinal structure on the downthrown side of a major east-west fault with oil and gas production from the upper part of the Wilcox formation. Two main producing horizons occur at an approximate depth of 11,500 ft and have been designated the Morein sand and the Deshotels sand. The upper sand (Morein) had an original bottom-hole pressure of 6,788 psig, which is some 1,500 psi above the normal pressure for that depth. Oil production with high gas/oil ratios and fluid analyses giving high shrinkage factors prompted a study of the reservoir in its early stages. The results indicated a closed reservoir producing under solution gas drive with low expected ultimate oil recovery. The early study of the Wilcox formation and its contained hydrocarbons resulted in the presentation of the data to the Department of Conservation of the State of Louisiana. with suggestions for field rules and a request for permission to inject extraneous water into the Morein sand. The water injection plans eventually led to complete unitization of working and royalty interests, to the construction of a gasoline plant, and to a central tank battery installation for the field. Deshotels sand wells were reworked to the Morein sand, and the water injection system was installed and ready for continuous operation in the early part of 1949. The injection of water was started in time to arrest the bottom-hole pressure decline at or near the bubble-point pressure. This injection was calculated to increase the ultimate recovery and to conserve natural resources. Pressure maintenance, the extraction of LPG products, and the sale of residue gas (early 1950) represent an attempt to produce an oil field with utmost efficiency. INTRODUCTION The two principal Wilcox oil horizons in the Mamou Field are the Morein sand and the Deshotels sand, occurring at 11,500 ft and 11,700 ft subsea, respectively. Minor oil production has been encountered in Morein stringer sands. (Fig. 1.) This paper deals only with the Morein sand, which is blanket over the Mamou Field. It is, however, segmented by the northwest-southeast "E" fault as shown in Fig. 2. The west segment is the area involved in the water injection pressure maintenance program. To date the east segment has operated largely under the influence of a strong water drive. The paper presents (1) a brief history of field development, (2) a resumé of reservoir conditions which led to the decision to inject extraneous salt water into the principal producing horizon, and (3) a summary of reservoir analysis and performance. FIELD DEVELOPMENT The Mamou Field is located in Evangeline Parish, La. The discovery well (J. B. Morein No. 1, now Unit No. 5) was completed in December, 1945, after penetrating 200 ft into the Wilcox formation. Initial production from the Morein

Jan 1, 1951

By Charles A. Anderson

The Bagdad copper deposit is of the disseminated type (porphyry copper) occurring in a quartz monzonite stock of late Cretaceous or early Tertiary age. This stock, located essentially at the intersection of two dike swarms, is the only one of several stocks cropping out in the area which is appreciably fractured and mineralized. Most of the rocks in the area are of pre-Cambrian age, but their structures have had no discernible influence on the copper mineralization. Hypogene alteration of the quartz monzonite includes the addition of quartz, orthoclase, and sericite and recrystalli-zation of biotite. The hypogene sulphides are pyrite, chalcopyrite, and molybdenite, the latter younger than the chalcopyrite. The late Cretaceous or early Tertiary igneous rocks, veins, and faults were controlled by northeast and northwest shear zones, the intersection of which marks the zone of appreciable copper mineralization. The minor mineralized fractures carrying the bulk of the copper have a preferred orientation parallel to the intersecting shears, and it is concluded that they are of tectonic origin rather than the result of shrinkage on cooling, crystallization, or mineralization. Supergene enrichment during late Tertiary or early Pleistocene time formed a chalcocite zone providing the minable copper ore. The enrichment was controlled in large part by northeast and northwest faults, prticularly at their intersection or where the faults are closely spaced. Introduction A major objective in a regional geologic study of a mining district is to determine whether any structural pattern can be found that has a bearing on the control of mineralization. The Bagdad copper deposit is of the disseminated type (porphyry copper) occurring in a.quartz monzonite stock which is located essentially at the intersection of two dike swarms (Fig 2). Of several quartz monzonite stocks in the area only this One is appreciably fractured and mineralized. The origin of the minute mineralized fractures in disseminated copper deposits has long been a challenging problem to the mining geologist, and evidence has been obtained to suggest that the mineralized fractures at Bagdad are related to a regional pattern of conjugate shears which also controlled the location of the dike swarms. The purpose of this paper is to Present this evidence and to emphasize the structural control of the supergene enrichment in forming a chalcocite zone that has provided the ore for the Bagdad mine. The field work on which these conclusions are based was done between October 1943 and August 1945, as a part of the copper investigations of the Goelogical Survey, U. S. Department of the Interior. The writer and his associates, E. A. Scholz and J. D. Strobell, Jr., have prepared a comprehensive report on the geology and ore deposits of the Bagdad area which will be published subsequently by the Geological Survey. Bagdad is located in west-central Arizona in Yavapai County. Ransome' divided the State of Arizona into three provinces: I? the plateau to the northeast; 111, the desert region to the southwest and 11, the moun-

Jan 1, 1949

By Charles A. Anderson

The Bagdad copper deposit is of the disseminated type (porphyry copper) occurring in a quartz monzonite stock of late Cretaceous or early Tertiary age. This stock, located essentially at the intersection of two dike swarms, is the only one of several stocks cropping out in the area which is appreciably fractured and mineralized. Most of the rocks in the area are of pre-Cambrian age, but their structures have had no discernible influence on the copper mineralization. Hypogene alteration of the quartz monzonite includes the addition of quartz, orthoclase, and sericite and recrystalli-zation of biotite. The hypogene sulphides are pyrite, chalcopyrite, and molybdenite, the latter younger than the chalcopyrite. The late Cretaceous or early Tertiary igneous rocks, veins, and faults were controlled by northeast and northwest shear zones, the intersection of which marks the zone of appreciable copper mineralization. The minor mineralized fractures carrying the bulk of the copper have a preferred orientation parallel to the intersecting shears, and it is concluded that they are of tectonic origin rather than the result of shrinkage on cooling, crystallization, or mineralization. Supergene enrichment during late Tertiary or early Pleistocene time formed a chalcocite zone providing the minable copper ore. The enrichment was controlled in large part by northeast and northwest faults, prticularly at their intersection or where the faults are closely spaced. Introduction A major objective in a regional geologic study of a mining district is to determine whether any structural pattern can be found that has a bearing on the control of mineralization. The Bagdad copper deposit is of the disseminated type (porphyry copper) occurring in a.quartz monzonite stock which is located essentially at the intersection of two dike swarms (Fig 2). Of several quartz monzonite stocks in the area only this One is appreciably fractured and mineralized. The origin of the minute mineralized fractures in disseminated copper deposits has long been a challenging problem to the mining geologist, and evidence has been obtained to suggest that the mineralized fractures at Bagdad are related to a regional pattern of conjugate shears which also controlled the location of the dike swarms. The purpose of this paper is to Present this evidence and to emphasize the structural control of the supergene enrichment in forming a chalcocite zone that has provided the ore for the Bagdad mine. The field work on which these conclusions are based was done between October 1943 and August 1945, as a part of the copper investigations of the Goelogical Survey, U. S. Department of the Interior. The writer and his associates, E. A. Scholz and J. D. Strobell, Jr., have prepared a comprehensive report on the geology and ore deposits of the Bagdad area which will be published subsequently by the Geological Survey. Bagdad is located in west-central Arizona in Yavapai County. Ransome' divided the State of Arizona into three provinces: I? the plateau to the northeast; 111, the desert region to the southwest and 11, the moun-

Jan 1, 1949

By Irwin Roman

In studying the possibilities of a continuously recording magnetometer for use along the surface of the earth and in an airplane, the Federal Bureau of Mines was led to a study of the theoretical resolving power of magnetic observations, both in the variation of the total magnetic intensity and in each of the two cornponents ordinarily measured. Along with this general study, an attempt was made to determine the relative worth of the total intensity anomaly and the vertical anomaly in geophysical prospecting. Genera1 considerations led to three conclusions: I. In the northern magnetic hemisphere of the earth, the total intensity anomaly is offset to the south of the vertical anomaly, for a positive anomaly (see Appendix, note 1). 2. The resolving power of magnetic observations decreases rapidly with distance from the disturbing body. 3. The horizontal anomaly has little value in prediction of the disturbing body but might be useful in making a choice between bodies suggested by the vertical or total anomaly. Some of the considerations leading to these conclusions were: I. The normal intensity and the anomalous intensity are vectorially additive; hence for a positive anomaly in the northern magnetic hemisphere the total intensity will be a maximum at some point south of the disturbing body and north of the point at which the line to the disturbing body is parallel to the normal earth's field. The anomaly itself has a maximum value directly above the body. For a positive anomaly of constant magnitude, the total intensity will be a maximum when the anomaly vector is parallel to the normal vector. This is shown schematically in Fig. I (not to scale) for a magnetic distribution not restricted to a relatively thin sheet in the magnetic meridian. The normal field has a magnitude 10 with vertical component V0 and horizontal component Ho. Six station points along a traverse across the body from south to north are shown at M to S. At each of these stations the normal magnetic field vector terminates at F. At each of these stations the magnetic field vector due to the disturbing body B terminates at A. The line through the station point and the point A passes through B. The magnitude of the anomaly, indicated by the length of the vector terminating at A, is proportional to some power of the distance from the station point to the disturbing body. If the disturbing body B is a concentrated point of magnetic material, the anomaly is proportional to the inverse second power of the distance. For a uniform magnetic distribution over a line perpendicular to the observed traverse, the anomaly is proportional to the inverse first power of the distance. For surface distributions, the law of intensity is more complicated. At each field point, the total magnetic intensity T is the vector sum of the

Jan 1, 1949

By A. W. D. Hills

This paper describes the development of a generalized integral-Wofile method for the analysis of heat transfer dwing solidification. The method is extremely flexible, and can be applied to a wide range of situations. This flexibility has been achieved by characterizing the solid metal layer in terms of two parameters, and by developing two simultaneous nonlinear differential equations for these parameters in terms of the heat fluxes crossing the boundaries of the solid layer. The use of these equations is illustrated in a series of examples which involve the solidification of pure metals at zero superheat cooling under different conditions. The simplicity with which the method can be extended to treat more complicated jwoblems is illustrated in a further example which involves natwal convection effects in the liquid metal. ThE rate at which molten metal solidifies in an industrial casting process, and the structure of the cast product, are both controlled by the rate at which heat can be removed from the casting. A knowledge of heat transfer rates is thus essential to the control of the process and to the control of the structure and soundness of the final casting. Heat transfer rates during real solidification processes cannot be predicted by formal mathematical techniques, however, because nonlinear boundary conditions are involved. Approximate methods are normally used, and these have included electrical and hydraulic analogue techniques, finite difference methods, and the integral-profile method. Considerable effort has been devoted to the development of the first two techniques, but the integral-profile method has been used very little so far. This is unfortunate because the method is capable of providing relatively accurate solutions for the heat transfer equation during solidification without involving large amounts of computer time. A further advantage of the method is its flexibility, although this is not apparent from the integral-profile solutions that have been developed to date. These solutions have been derived for the solidification of molten metal at zero super-heat under cooling conditions involving either a constant heat flux from the cooled surface;' a constant heat transfer coefficient at the surface,'-3 or a specified variation in the surface temperature.4,5 A generalized integral-profile method is presented in this paper which can be used to predict unidirectional solidification rates under a very wide range of more realistic cooling conditions. The use of the method is illustrated in a series of problems involving pure metals, or skin forming alloys, solidifying at zero super-heat. However, the principal advantage that this method has over the previous integral-profile methods is the ease with which it can be extended to treat more complicated solidification problems. This is illustrated by considering a problem in which super-heat is liberated from the liquid metal by natural convection during the solidification process. In the final section of the paper the generalized method is compared with previous methods used to predict solidification rates and its extension to more complicated solidification problems is briefly discussed.

Jan 1, 1970

By J. A. Morgan, R. E. Lund, D. E. Warnes

The design, operation, and performance of an integrated pilot plant for recovering zinc and copper from a complex sulfide ore are described. Metallurqical processing comprised selective sulfate roasting in a fluid bed, leaching in a weak sulfuric acid solution, recovering copper by cementation with scrap iron, air oxidation to remove soluble iron, more-or-less conventional Purification for removal of impurities deleterious to zinc electrolysis, recovering zinc by electrolyzing solutions, and recycling spent electrolyte to the sulfating roaster. The effects of several feed preparation and roasting variables on the sulfation response of zinc, copper, and iron are set forth, together with the electrolyzing characteristics of the zinc solutions. SEVERAL years ago, St. Joseph Lead Co. undertook a research program to develop procedures for winning values from a complex ore. The deposit was a massive sulfide ore body containing upwards of 65 pct pyrite. Gangue, composed principally of quartz, calcite, dolomite, and alumina, comprised only 10 to 20 pct of the mineralized zones. Zinc, lead, and copper values were variable, but averaged about 6.7 pct Zn, 2.6 pct Pb, and 0.4 pct Cu. Early in the exploratory test work, it was established that the intimate physical association of the minerals in the ore made beneficiation by conventional flotation procedures difficult. Accordingly, in addition to a comprehensive program to investigate physical methods of ore beneficiation, a research program was established to develop a direct metallurgical method for processing the ore. After surveying a number of potential methods for recovery of both metal and sulfur values, effort was concentrated on the development of a sulfate roasting process. It is the pilot-plant development of the sulfate roasting-solution purification—electrolyzing procedures which forms the subject of the present paper. PREPILOT PLANT INVESTIGATIONS From a thermodynamic viewpoint, it is feasible to sulfate selectively a host of metals, including Zn, Cu, Pb, Cd, Ni, and Co, in an iron sulfide ore without sulfating iron. Of course, a number of conditions such as roasting temperature and gas composition must be controlled. In addition, as first disclosed by Hybinette,' an alkali metal salt is frequently beneficial in promoting the sulfation reactions. The application of fluid bed roasting to the sulfate roasting of nonferrous metals was pioneered by Stephens of Battelle Memorial Institute.' Subsequently, Falconbridge Nickel Mines, Ltd. developed an unique process for selectively sulfating and recovering nickel, copper, and cobalt from their nickeliferous pyrrhotite, which recently has been described in an excellent paper by Thornhill.3 One of the unique features of the Falconbridge process is that the feed is introduced into the fluidized roasting furnace in a manner such that the feed slurry is broken up into droplets and the droplets lose their moisture before contacting the surface of the fluidized bed. The dried droplets do not tend to cake or fuse, but rather remain as discrete agglomerates of concentrate particles and roast without significant degradation. St. Joseph, aware that Battelle Memorial Institute had participated in the development of the Falconbridge process, obtained permission from Falcon-

Jan 1, 1962

By H. K. Work

The Bessemer process is one of the most interesting methods of making steel. At one time it was by far the most important. In recent years, however, it has steadily lost ground to the open-hearth process. The forces working against this method of stccl-making are partly economic and partly metallurgical.1 In this paper, dealing as it does with the control of the process, the metallurgical factors alone will be considered, although it is obvious that economic factors must play a part in determining the ultimate status of the Bessemer process. This discussion has been limited in another respect—it deals primarily with the acid Bessemer process in bottom-blown converters, although much of the information is applicable to basic and side-blown converters. The fact that open-hearth steel has superseded Ressemer steel to a large extent has tended to create an impression that Bessemer steel is inferior. As a matter of fact, Bessemer steel is actually superior to open-hearth for many applications.2 There are, however, definite metallurgical limitations to the use of Bessemer steel, resulting largely from two factors: (1) the physical properties conferred by nitrogen and phosphorus, and (2) the variability from blow to blow. These, of course, are not entirely independent, since some of the variability covered in the second item is undoubtedly due to nitrogen. But the variability is also caused by other factors. One of these is the relatively small size of the Bessemer heats. Because of this, a given shipment of Bessemer steel is more likely than a shipment of open-hearth steel to contain the product of several heats, each with its own distinctive and slightly different characteristics. Added to this is the fact that the refining of Bessemer steel proceeds so rapidly that the timing of the end point is limited to a matter of seconds, whereas the finishing period in the open hearth extends over a period of one or two hours and the timing of the end point may vary by several minutes without seriously affecting the product. There is no doubt that this has contributed to the variability of Bessemer steel and has led to the use of open-hearth steel in many optional applications. That Bessemer steel may vary is not necessarily objectionable, and it may even prove an advantage, providing a precise control is available to secure the desired qualities for any specific application. With this in mind, a comprehensive research program was undertaken, one phase of which was directed toward securing more accurate control of the blow. The results have been encouraging, and it is the purpose of this paper to describe a method in which modern scientific instruments, based on photocells, are currently being employed to assist the blower. The Control Problem In this day of scientific control of technical processes, where the operating

Jan 1, 1941

By Carlton Beal

This paper presents useful charts for conversion of various viscosimeter units into centipoises and graphically summarizes published investigations of the viscosity of air, water and natural gas at high temperatures and pressures. Where possible, charts and correlations were constructed to cover a range of temperature (60°F. to 300°F.) and pressure (14.7 lb. per sq. in. abs. to 8000 lb. per sq. in. gauge) encountered in oil fields. Correlation charts, for the purpose of predicting crude oil viscosity and solubility behavior at oil field temperatures and pressures, were constructed from an analysis and correlation of 1332 viscosity and solubility observations from 953 crude oil samples taken from 747 oil fields. Of these fields, 501 are in the United States, including 75 in California. Of the 1332 observations, 1215 were viscosity values, including 786 of gas-free crude oil, 351 of oil saturated with gas, and 78 under-saturated with gas at pressures above the bubble point. Results show that crude oil viscosity at various reservoir conditions can be predicted with average deviations varying from 24.2 per cent for gas-free crude oil to as little as 2.7 per cent for undersaturated crude oil "above the bubble point." The solubility of crude oil may be predicted from oil gravity and saturation pressure with an average deviation of 22.0 per cent from observed values. In conclusion, it is shown that the viscosity of a gas and gas-saturated crude oil may be predicted within the accuracy of most reservoir computations. Viscosity is a measure of flow resistance; common units are in centipoises (cp.). The object of this report is to present conversion charts and simplified 'correlation charts showing the viscosity behavior of air, water, gas and crude oil and gas-saturated crude oil under oil field temperatures and pressures, which have been known to be as high as 300°F. and 8000 Ib. per sq. in. gauge under subsurface conditions. The viscosity of a liquid or gas is important because it is a measure of its fluidity, or its ability to flow through pipe lines or oil sands. Viscosity of air has become important because it is being used in secondaryl,2 recovery projects. The viscosity of natural gas and water at reservoir conditions is useful because they are almost universally associated and produced with crude oil. The viscosity of gas-saturated crude oil at reservoir pressures and tem peratures is of particular value in making estimates of oil reserves3 and rate of oil recovery from flush pools when production decline data are limited. Instruments Used to MeasuRe Viscosity There are many types of viscosimeters,4 and the instruments most commonly used to measure the atmospheric viscosity of liquids at moderate temperatures and their practical working ranges have been deScribed5,6 in detail. Fig. I and Fig. 2 are viscosity conversion charts which have

Jan 1, 1946

By Nicholas J. Grant, W. Michael Yim

The creep-rupture properties of nickel, in as-prestrained or prestrain-polygonized condition, were studied at 1300°F and 4000 psi, and also at 700°F and 26,000 psi. An improvement of strength was noted in both the as -prestrained and the prestrain-polygonized tests at each temperature. The as-prestrained tests, however, showed superior creep resistance to the prestrain-polygonized ones. From the results of X-ray and etch-pit studies, the strengthc gain was interpreted in terms of dislocation density and the stability of preformed substructures. COLD work is known to improve the strength properties of metals at low temperatures. At high temperatures, however, the strength improvement is often lost if gross structural changes, such as re-crystallization, take place prior to or during the test. Even in the absence of recrystallization, a prestrained metal may undergo structural changes— polygonization and the formation of well-defined subgrains—which importantly effect the resultant properties. The relationship between substructure and creep properties has received considerable attention in recent years. The work of wood1 indicated that the creep strength of aluminum and its alloys was closely related to the subgrain size. Hazlett and Hansen,2 and Ancker, Hazlett, and parker,3 working with nickel and nickel alloys, had shown that small amounts of prestrain at room temperature followed by a recovery anneal at 800°C (1470°F) improved the strength at both low and high temperatures. The strength gain was attributed to an increase in the number of subgrain boundaries as a result of the prestrain-polygonization treatment. More recently Coldren and Freeman4 studied the effect of substructures on the creep rate of nickel at 1550°F. Their conclusions indicated that the substructure size as measured by the number of boundaries was the factor that controlled the creep rate. In addition, the perfection of the subgrain boundary has been indicated to have an important role on the strength.' On the other hand, there are data which disagree with the above observations. Grant, Chaudhuri, Silver, and Ganow6 found no creep strength improvement by a prestraining treatment. In reviewing the role of subgrains on high-temperature creep, Shepard and Dorn7 concluded that the contribution of the subgrains to high-temperature creep strength was a minor one. Guard,8 in a recent study on poly-gonized nickel, has cast doubt on the validity of the postulate that subgrain size controls the creep rate. In the majority of the previous studies, the subgrain boundaries have been singled out as the most important factor in determining creep strength; however, there is no firm theoretical ground for the postulate that the subgrain boundaries act as effective barriers to dislocation motion.B910 Little effort has been directed toward the study of the relationship between creep strength and other structural variables, such as dislocation density, lattice strain,

Jan 1, 1963

By Carlton Beal

This paper presents useful charts for conversion of various viscosimeter units into centipoises and graphically summarizes published investigations of the viscosity of air, water and natural gas at high temperatures and pressures. Where possible, charts and correlations were constructed to cover a range of temperature (60°F. to 300°F.) and pressure (14.7 lb. per sq. in. abs. to 8000 lb. per sq. in. gauge) encountered in oil fields. Correlation charts, for the purpose of predicting crude oil viscosity and solubility behavior at oil field temperatures and pressures, were constructed from an analysis and correlation of 1332 viscosity and solubility observations from 953 crude oil samples taken from 747 oil fields. Of these fields, 501 are in the United States, including 75 in California. Of the 1332 observations, 1215 were viscosity values, including 786 of gas-free crude oil, 351 of oil saturated with gas, and 78 under-saturated with gas at pressures above the bubble point. Results show that crude oil viscosity at various reservoir conditions can be predicted with average deviations varying from 24.2 per cent for gas-free crude oil to as little as 2.7 per cent for undersaturated crude oil "above the bubble point." The solubility of crude oil may be predicted from oil gravity and saturation pressure with an average deviation of 22.0 per cent from observed values. In conclusion, it is shown that the viscosity of a gas and gas-saturated crude oil may be predicted within the accuracy of most reservoir computations. Viscosity is a measure of flow resistance; common units are in centipoises (cp.). The object of this report is to present conversion charts and simplified 'correlation charts showing the viscosity behavior of air, water, gas and crude oil and gas-saturated crude oil under oil field temperatures and pressures, which have been known to be as high as 300°F. and 8000 Ib. per sq. in. gauge under subsurface conditions. The viscosity of a liquid or gas is important because it is a measure of its fluidity, or its ability to flow through pipe lines or oil sands. Viscosity of air has become important because it is being used in secondaryl,2 recovery projects. The viscosity of natural gas and water at reservoir conditions is useful because they are almost universally associated and produced with crude oil. The viscosity of gas-saturated crude oil at reservoir pressures and tem peratures is of particular value in making estimates of oil reserves3 and rate of oil recovery from flush pools when production decline data are limited. Instruments Used to MeasuRe Viscosity There are many types of viscosimeters,4 and the instruments most commonly used to measure the atmospheric viscosity of liquids at moderate temperatures and their practical working ranges have been deScribed5,6 in detail. Fig. I and Fig. 2 are viscosity conversion charts which have

Jan 1, 1946

By H. K. Work

THE Bessemer process is one of the most interesting methods of making steel. At one time it was by far the most important. In recent years, however, it has steadily lost ground to the open-hearth process. The forces working against this method of steelmaking are partly economic and partly metallurgical.' In this paper, dealing as it does with the control of the process, the metallurgical factors alone will be considered, although it is obvious that economic factors must play a part in determining the ultimate status of the Bessemer process. This discussion has been limited in another respect-it deals primarily with the acid Bessemer process in bottom-blown converters, although much of the information is applicable to basic and side-blown converters. The fact that open-hearth steel has superseded Bessemer steel to a large extent has tended to create an impression that Bessemer steel is inferior. As a matter of fact, Bessemer steel is actually superior to open-hearth for many applications.2 There are, however, definite metallurgical limitations to the use of Bessemer steel, resulting largely from two factors: (I) the physical properties conferred by nitrogen and phosphorus, and (2) the variability from blow to blow. These, of course, are not entirely independent, since some of the variability covered in the second item is undoubtedly due to nitrogen. But the variability is also caused by other factors. One of these is the relatively small size of the Bessemer heats. Because of this, a given shipment of Bessemer steel is more likely than a shipment of open-hearth steel to contain the product of several heats, each with its own distinctive and slightly different characteristics. Added to this is the fact that the refining of Bessemer steel proceeds so rapidly that the timing of the end point is limited to a matter of seconds, whereas the finishing period in the open hearth extends over a period of one or two hours and the timing of the end point may vary by several minutes without seriously affecting the product. There is no doubt that this has contributed to the variability of Bessemer steel and has led to the use of open-hearth steel in many optional applications. That Bessemer steel may vary is not necessarily objectionable, and it may even prove an advantage, providing a precise control is available to secure the desired qualities for any specific application. With this in mind, a comprehensive research program was undertaken, one phase of which was directed toward securing more accurate control of the blow. The results have been encouraging, and it is the purpose of this paper to describe a method in which modern scientific instruments, based on photocells, are currently being employed to assist the blower. THE CONTROL PROBLEM In this day of scientific control of technical processes, where the operating

Jan 1, 1941

By James M. Stapleton

IT has long been recognized by blast- furnace men that correct top distribution of materials is very important in efficient and economical furnace operation. Thousands of experiments on top design, filling, sizing, and other operations have been carried out to improving furnace performance by securing uniform distribution. Many of these experiments have worked out satisfactorily and have been passed along to the industry. Many of them have been discarded and forgotten. It has been the custom to judge the results of such experimentation by the results shown in improved or lowered furnace efficiency. While the effect on furnace practice will have to continue to be the final criterion of experimental changes, it has always been a desire of blast-furnace men to ascertain the reason for failure or success. Efficiency in the blast furnace approaching the maximum can be measured in several ways: (I) by actual operating results as revealed in the coke rate and tonnage figures, and (2), in the degree to which the top gas approaches the limiting ratio of CO/C02 for the reduction of iron oxide by CO gas. This ratio is shown in the equilibrium curve in Fig. I for the system Fe-O-C and CO2-CO-C. The closer the top gases approach this limiting ratio (set at 1.08 by Martin1 because of the effect of limestone calcination) the more efficiently we may expect a furnace to operate. The fact that low CO/C02 ratios parallel eficient operating performance caused us to investigate the cause of good or poor distribution and the effect of filling and other changes on furnace operation. Heretofore it has been possible to take a sample of furnace gas (usually from the dust catcher) and from it determine how closely the reducing gases were to the ideal or limiting value as set by the equilibrium diagram. However, to find just where in the top area the distribution was distorted and the top-gas CO/CO2 ratios were distant from equilibrium values has been a difficult and expensive investigational procedure. In an effort to overcome this difficulty, apparatus was designed to take gas samples and temperatures across the top radius of the furnace. It was hoped that with the aid of this apparatus traverse sampling of the ascending gases could be simplified, and the cost of sampling substantially lowered. Routine experimenting could then be maintained and results checked with furnace operation. It must be emphasized that a traverse sampling is necessary for a true picture, as single samples at any one point are unreliable. This statement can be verified by an examination of Tables 3 to 6, showing results obtained at our furnaces in a large number of tests. APPARATUS The design of the equipment for taking the samples was governed by the need for providing a simple, routine test that could be performed fairly quickly without adversely affecting normal furnace operation.

Jan 1, 1943

By H. K. Work

The Bessemer process is one of the most interesting methods of making steel. At one time it was by far the most important. In recent years, however, it has steadily lost ground to the open-hearth process. The forces working against this method of stccl-making are partly economic and partly metallurgical.1 In this paper, dealing as it does with the control of the process, the metallurgical factors alone will be considered, although it is obvious that economic factors must play a part in determining the ultimate status of the Bessemer process. This discussion has been limited in another respect—it deals primarily with the acid Bessemer process in bottom-blown converters, although much of the information is applicable to basic and side-blown converters. The fact that open-hearth steel has superseded Ressemer steel to a large extent has tended to create an impression that Bessemer steel is inferior. As a matter of fact, Bessemer steel is actually superior to open-hearth for many applications.2 There are, however, definite metallurgical limitations to the use of Bessemer steel, resulting largely from two factors: (1) the physical properties conferred by nitrogen and phosphorus, and (2) the variability from blow to blow. These, of course, are not entirely independent, since some of the variability covered in the second item is undoubtedly due to nitrogen. But the variability is also caused by other factors. One of these is the relatively small size of the Bessemer heats. Because of this, a given shipment of Bessemer steel is more likely than a shipment of open-hearth steel to contain the product of several heats, each with its own distinctive and slightly different characteristics. Added to this is the fact that the refining of Bessemer steel proceeds so rapidly that the timing of the end point is limited to a matter of seconds, whereas the finishing period in the open hearth extends over a period of one or two hours and the timing of the end point may vary by several minutes without seriously affecting the product. There is no doubt that this has contributed to the variability of Bessemer steel and has led to the use of open-hearth steel in many optional applications. That Bessemer steel may vary is not necessarily objectionable, and it may even prove an advantage, providing a precise control is available to secure the desired qualities for any specific application. With this in mind, a comprehensive research program was undertaken, one phase of which was directed toward securing more accurate control of the blow. The results have been encouraging, and it is the purpose of this paper to describe a method in which modern scientific instruments, based on photocells, are currently being employed to assist the blower. The Control Problem In this day of scientific control of technical processes, where the operating

Jan 1, 1941

By James M. Stapleton

It has long been recognized by blastfurnace men that correct top distribution of materials is very important in efficient and economical furnace operation. Thousands of experiments on top design, filling, sizing, and other operations have been carried out to improving furnace performance by securing uniform distribution. Many of these experiments have worked out satisfactorily and have been passed along to the industry. Many of them have been discarded and forgotten. It has been the custom to judge the results of such experimentation by the results shown in improved or lowered furnace efficiency. While the effect on furnace practice will have to continue to be the final criterion of experimental changes, it has always been a desire of blast-furnace men to ascertain the reason for failure or success. Efficiency in the blast furnace approaching the maximum can be measured in several ways: (1) by actual operating results as revealed in the coke rate and tonnage figures, and (2), in the degree to which the top gas approaches the limiting ratio of CO/CO2 for the reduction of iron oxide by CO gas. This ratio is shown in the equilibrium curve in Fig. I for the system Fe-O-C and CO2-CO-C. The closer the top gases approach this limiting ratio (set at 1.08 by Martin1 because of the effect of limestone calcination) the more efficiently we may expect a furnace to operate. The fact that low CO/CO2 ratios parallel eficient operating performance caused us to investigate the cause of good or poor distribution and the effect of filling and other changes on furnace operation. Heretofore it has been possible to take a sample of furnace gas (usually from the dust catcher) and from it determine how closely the reducing gases were to the ideal or limiting value as set by the equilibrium diagram. However, to find just where in the top area the distribution was distorted and the top-gas CO/CO2 ratios were distant from equilibrium values has been a difficult and expensive investigational procedure. In an effort to overcome this difficulty, apparatus was designed to take gas samples and temperatures across the top radius of the furnace. It was hoped that with the aid of this apparatus traverse sampling of the ascending gases could be simplified, and the cost of sampling substantially lowered. Routine experimenting could then be maintained and results checked with furnace operation. It must be emphasized that a traverse sampling is necessary for a true picture, as single samples at any one point are unreliable. This statement can be verified by an examination of Tables 3 to 6, showing results obtained at our furnaces in a large number of tests. Apparatus The design of the equipment for taking the samples was governed by the need for providing a simple, routine test that could be performed fairly quickly without adversely affecting normal furnace operation.

Jan 1, 1943

By James M. Stapleton

It has long been recognized by blastfurnace men that correct top distribution of materials is very important in efficient and economical furnace operation. Thousands of experiments on top design, filling, sizing, and other operations have been carried out to improving furnace performance by securing uniform distribution. Many of these experiments have worked out satisfactorily and have been passed along to the industry. Many of them have been discarded and forgotten. It has been the custom to judge the results of such experimentation by the results shown in improved or lowered furnace efficiency. While the effect on furnace practice will have to continue to be the final criterion of experimental changes, it has always been a desire of blast-furnace men to ascertain the reason for failure or success. Efficiency in the blast furnace approaching the maximum can be measured in several ways: (1) by actual operating results as revealed in the coke rate and tonnage figures, and (2), in the degree to which the top gas approaches the limiting ratio of CO/CO2 for the reduction of iron oxide by CO gas. This ratio is shown in the equilibrium curve in Fig. I for the system Fe-O-C and CO2-CO-C. The closer the top gases approach this limiting ratio (set at 1.08 by Martin1 because of the effect of limestone calcination) the more efficiently we may expect a furnace to operate. The fact that low CO/CO2 ratios parallel eficient operating performance caused us to investigate the cause of good or poor distribution and the effect of filling and other changes on furnace operation. Heretofore it has been possible to take a sample of furnace gas (usually from the dust catcher) and from it determine how closely the reducing gases were to the ideal or limiting value as set by the equilibrium diagram. However, to find just where in the top area the distribution was distorted and the top-gas CO/CO2 ratios were distant from equilibrium values has been a difficult and expensive investigational procedure. In an effort to overcome this difficulty, apparatus was designed to take gas samples and temperatures across the top radius of the furnace. It was hoped that with the aid of this apparatus traverse sampling of the ascending gases could be simplified, and the cost of sampling substantially lowered. Routine experimenting could then be maintained and results checked with furnace operation. It must be emphasized that a traverse sampling is necessary for a true picture, as single samples at any one point are unreliable. This statement can be verified by an examination of Tables 3 to 6, showing results obtained at our furnaces in a large number of tests. Apparatus The design of the equipment for taking the samples was governed by the need for providing a simple, routine test that could be performed fairly quickly without adversely affecting normal furnace operation.

Jan 1, 1943