Search Documents

By R. Lingle, E. Hardin, M. Board, H. Pratt, W. Ubbes, M. Voegele, N. Barton

A 2 m. cube of jointed, Pre Cambrian biotite gneiss was subjected to uniaxial and biaxial loading at ambient and elevated temperature. The effects of different boundary conditions on the following rockmass properties were investigated: deformation modulus, joint stiffness, dynamic modulus, coefficient of thermal expansion, thermal diffusivity and conductivity, and joint permeability. Test conditions ranged between 0 and 6.9 MPa uniaxial and biaxial load, and 12° to 74°C mean block temperature. The tests were performed as part of the Office of Nuclear Waste Isolation program for evaluating site charterization test methods for measuring the hydro-thermal-mechanical properties of rock masses. The fracture flow experiments discussed in this paper were described in detail in a similar paper given to this symposium in 1981 (Voegele, 1981). DEFORMATION MODULUS Horizontal deformation measurements oriented parallel to the loading direction were made at the block surface. Several instrument types were employed: surface short-rod extensometers, bonded strain gauges, vibrating wire strain gauges and the Whittemore caliper strain gauge. Two vertical and two slant borehole extensometers measured vertical displacement. Loading history, especially during uniaxial loading, was critical to interpretation of observed deformation and fracture flow data. This important tendency has been observed in other large-scale laboratory (Bandis, 1980) and field tests (Pratt, et al., 1977). Excavation of the block resulted in minimal disturbance to the intrinsic condition of the sample. Even so, permanent, unrecovered "set" was imparted to the block beginning with the first low-stress biaxial load cycle to 3.45 MPa (Table 1). Unloading

Jan 1, 1982

By Charles R. Keyes

During the past decade the genesis of the lead- and zincdeposits of the Mississippi valley has received special attention from many distinguished observers. But their united egorts, instead of settling all disputed questions, have, in many respects, involl-ed the general problem in greater uncertainty than would be thought possible under the circumstances. In place of the harmony of opinion that might be expected, there is unexpected disagreement, largely due to the fact that, instead of giving attention to a possible multiplicity of ore-producing conditions among the different deposits, the attempt has been made to bring all deposits under a single genetic head. To a new observer of the lead- and zinc-deposits of the Mississippi valley, it appears at the outset that all the deposits cannot possibly have had the same genesis. In fact, different modes of origin have been often asserted for the ore-bodies, but the difficulty has been that each writer has referred them either all to one category or all to another, and no intermediate ground has been considered possible. Such a position now appears to be clearly untenable. The opinion that, in the deposits of the region under consideration, the ore-materials represent original depositions, made at the time the rocks themselves were formed, is no longer held by any authority, and therefore need not be considered here. Of late years, a number of writers have attempted to account for the presence of the lead- and zinc-ores on the hypothesis that the metallic materials arose in heated solutions from the

Jan 1, 1902

By George F. Becker

Complexity of Rock-Fractures.—The strains to which rocks have been subjected are manifestly very complex, and it is entirely safe to presume that every possible mode of deformation and rupture is exemplified. The most superficial inspection of any ordinary mountain region is sufficient to assure the observer that the rocks have been pressed, stretched, bent, buckled, twisted, and shorn. The study of torsional rupture cannot fail, therefore, to throw light on geological phenomena. The question is how areas which have been broken in this manner are to be distinguished from those which have yielded to other systems of forces. Phenomena of Joints.—It is well known that a large part of the more homogeneous rocks and some very heterogeneous rocks are intersected by partings often ailed joints. These partings are frequently flat surfaces even when seen in very large exposures, but are sometimes surfaces of moderate, single, or double curvature. Joint, usually occur in groups, in each of which the several partings are parallel to one another, and several such groups often intersect the same rock-mass. In such cases the different systems make large angles with one another. Nearly all students of the subject of jointing have reached the conclusion that joints are faulted surfaces, the dislocations usually being of small amplitude; and this conclusion receives abundant support from the study of thin sections under the microscope. It has thus been shown that much even of what would be regarded in hand specimens as mere slaty cleavage

Jan 1, 1895

By Prince Gelasio Caetani

PRESIDENT DWIGHT'S invitation to be a guest of the American Institute of Mining and Metal-lurgical Engineers was the first of the subsequently very numerous invitations to dinner I have received from my American friends. When I received his telegram I had not yet been even formally appointed Ambassador. I cannot tell you how deeply I appreciated it. It was a hearty welcome in returning to your country which has been for me a second home and it came from the American mining brotherhood which has been my second family.There are two distinct periods of learning in life. The first one are the years spent in school where we learn many things we after-wards forget; the second one are the years of prac-tical apprenticeship which engrave indelible signs in a man's character and shape his life. These latter years I spent in the United States and they have influenced the whole course of my life. I owe very much to my American friends who trained me. The earliest was Prof. Robert Peele, of Columbia University. At the Daly West mine, in Park City, Utah, he curbed my futuristic English spell-ing and had a hard time at it. Prof. James F. Kemp taught me that geology is a guess work just as unre-liable as the prediction of international events; he taught me also that a frank, honest and loyal character will lead a man equally straight through a mining report and through public life.

Jan 3, 1923

By G. H. Billings

There exists an unconfirmed opinion among many ironmasters that the combination of a small quantity of manganese, chromium, titanium, tungsten, aluminium, nickel, and some of the metalloids with iron has a beneficial effect upon the quality. And the impression prevails in some localities that the excellence of steel greatly depends upon the influence of some of these elements. Brit as the recorded experiments are so meagrely described, and made under such various conditions, the student in search of information upon the subject is somewhat bewildered by the contradiction of the opinions expressed. Observing some interesting phenomena while experimenting with an alloy of iron, copper, and nickel, I was led to determine the effect of some of the metals upon iron as free from contamination by other elements as it is possible to procure in practice, in order that the result of an alloy of an individual metal with iron might be more closely studied; for it is almost an impossibility to determine the influence of a small amount of one element upon a metal combined with a large amount of another, and the mere presence of another sometimes makes this difficult. And as most of the experiments recorded upon this subject have been made with iron containing sufficient carbon and other elements to interfere with the effect of that metal the influence of which it was desired to observe, I have endeavored to avoid these sources of error as far as practicable. In determining the specific gravity of the alloys in these ex-

By G. H. Billings

THERE exists an unconfirmed opinion among many ironmasters that the combination of a small quantity of manganese, chromium, titanium, tungsten, aluminium, nickel, and some of the metalloids with iron has a beneficial effect upon the quality. And the impression prevails in some localities that the excellence of steel greatly depends upon the influence of some of these elements. But as the recorded experiments are so meagrely described, and made under such various conditions, the student in search of information upon the subject is somewhat bewildered by the contradiction of the opinions expressed. Observing some interesting phenomena while experimenting with an alloy of iron, copper, and nickel, I was led to determine the effect of some of the metals upon iron as free from contamination by other elements as it is possible to procure in prac¬tice, in order that the result of an alloy of an individual metal with iron might be more closely studied ; for it is almost an impossibility to determine the influence of a small amount of one element upon a metal combined with a large amount of another, and the mere presence of another sometimes makes this difficult. And as most of the experiments recorded upon this subject have been made with iron containing sufficient carbon and other elements to interfere with the effect of that metal the influence of which it was desired to observe, I have endeavored to avoid these sources of error as far as practicable. In determining the specific gravity of the alloys in these ex-

Jan 1, 1877

By William Fraser

SINCE the operative word in the subject on which I have been asked to speak is "international," I need hardly emphasize before such an audience as this that it is one which calls for some discretion on my part at the present juncture of world affairs, since, in some respects, it may not be devoid of a controversial aspect. For though the war is over, it has left behind it a sorry state of health in the political and economic complex of the world we live in; and however different may be the impact of these factors on each of us, yet none of us can any longer hope to devise a system or policy to escape from much of its controversial heat, or evade the obligation of doing what we can to diminish it. I would like, therefore, to consider with you how one great form of world enterprise whose range is coextensive with material civilization itself-that is, the Petroleum Industry-can make and is competent to make, a contribution to international health; for it is now an agreed commonplace that oil is arterial in the world's system and we need no telling that a healthy body needs healthy blood. Before embarking on my subject, let me assure you that I have no need to be told that this country before all others-and for obvious reasons is the major sounding board of opinion in matters affecting most aspects of the petroleum industry-technical, economic, national and international (but, may I please add parenthetically, not to the exclusion of quite a

Jan 1, 1947

By W. C. Winegard, C. J. Simpson

BNINGESSNER et al.1 have shown that the solidification substructure in dilute cadmium alloys persisted after repeated deformation, recrystallization, and annealing treatments. On the basis of this and similar evidence, Whelan has suggested in a recent publication' that the solidification structure might affect the mobility of grain boundaries even after primary re-crystallization. This suggestion is important, since the technique used by previous investigators3-5 to fabricate grain growth specimens consisted only of casting, deforming, and recrystallizing prior to the grain growth anneal. Usually no attempt was made to homogenize samples with prolonged annealing. Experiments. To test the Whelan hypothesis, grain growth experiments were performed with samples in which the degree of solute segregation was altered by controlling the solidification rate of the alloys. The initial experiments were performed on the Pb-Ag system. Alloys containing 0.01 at. pct Ag were produced from 99.9999 pct Pb and 99.999 pct Ag. Cylindrical samples, 40 cm long and 12 mm in diam, were solidified in graphite-coated Vycor tubes by lowering them through a vertical furnace at varying rates with the furnace power settings constant. Six-centimeter sections were discarded from each end, and the 28-cm section from the center was cut into sections 25 mm long for grain growth experiments. These samples were deformed with the aid of a drophammer to a uniform thickness of 5.7 mm. After almost instantaneous recrystallization, the samples were given a grain growth anneal for various times at 260°C in a salt bath. Experimental results are shown

Jan 1, 1970

By J. K. Gustafson

Since prehistoric times, gold has been sought for its beauty and its unusual physical and chemical properties. Early in the dawn of civilization it became the ultimate unit of value, and for at least 6000 years it has been used to barter for other commodities. It has been prospected for, treasured and made into works of art and personal adornment. From time to time, it has even been the object of conquest. Because of its predominant role as a basis for money in recent centuries, economists have come to think of gold solely in these terms. Gold, however, has physical and chemical properties that make it one of the most useful metals in the modern world. It is the most ductile metal known. An ounce of it can be drawn into a continuous wire over 35 miles long. It is also so malleable that an ounce of it can be beaten into films 0.00001 in. thick covering 68 sq ft of surface. It has a density of 19.3 and is so heavy that 1 cu ft of it weighs more than half a ton. Gold is nonmagnetic and has a high electric conductivity that is only slightly less than that of silver and copper. Gold is so inert to all the chemicals found in nature that gold coins and jewelry buried beneath the soil or at the bottom of the sea for thousands of years appear to be as bright and perfect as when they were first immersed. Finally, gold has an extremely high reflectivity of both light and infrared rays.

Jan 1, 1971

By Bernard Rachlin

IN the mineral industry measurement of density or specific gravity of slurries is often necessary or highly desirable. To date the most successful method of measuring the specific gravity of various media is to hand weigh a constant volume sample of the slurry. This method is time-consuming, however, and is intermittent rather than continuous. Most density measuring instruments in use today are variations of three basic systems: air bubble tube systems, radioactive methods, and displacer systems. The high cost of the radioactive cell, combined with the precision electronic measuring that is required, limits the practical utility of this procedure to a small percentage of critical processes. In the air bubble systems clogging of the bubble tubes with solids has rendered this type of measurement completely ineffectual for many applications. Continuous or intermittent purging of the bubble tubes with air or water to prevent tube clogging has been tried but has not been very successful, especially in the heavy media process. The displacer system, which presents the fewest complications of all the density measuring systems, consists only of a metal immersion unit and a means of weighing it. In the past, settling of the solid in the slurry has caused untrue samples and clogging of the media at the bottom of the chamber. It is also important to dampen excessive flow surges such as those caused by reciprocating pumps. The system described here successfully overcomes these difficulties. Description of the Process System: The process equipment, on which the field tests were run, was a

Jan 1, 1957

By Robert Linton

The Sierra Consolidated Mines Co., organized in 1909, owns, together with other holdings, practically all of the productive mineral area in the Ocampo district. Lying within this area are 15 mines, large and small, that hid previously been worked and appear to have yielded, since the discovery of the camp, about 100 years ago, bullion of a total value of over $50,000,000. The deepest mine, the Santa Juliana, had been worked to 1,100 ft. below the outcrop. The reopening of the mines involved, first, extensive and thorough development to open up the known ore shoots at greater depth and explore the ledges for additional shoots, and, second, a revision of existing equipment and methods, so as to increase output and reduce cost of production. This paper will give some account of the metallurgical treatment and a description of the new mill to be built at El Salto. The Ore The ore is practically all argentite, Ag2S, with some associated gold, and carried in a siliceous gangue. The typical ledge matter is an ande-sitic breccia cemented with quartz, or quartz stockwork in andesite.l The proportion by weight of silver to gold averages about 60 to 1. The silver sulphides occur ordinarily in rather fine. dissemination, sometimes not being easily discernible with the naked eye, even in ores of very good grade. The ledges also contain considerable pyrites, which as a rule is barren. "Bronce" is the local term applied to such barren pyrites, and "Pasta" to such as carries values.

Jan 1, 1915

By John W. Tieman

Coal is a term applied to vegetable matter (trees, grasses, etc.) which was subjected to heat and pressure through geologic ages. This resulted in a change in both the physical and chemical properties. Because its chemical composition is variable, geologists classify coal as a heterogeneous mineral rather than a homogeneous mineral. Peat represents the initial, unconsolidated stage in the development of coal. This coalification continues with time and the application of temperature and pressure to lignite, subbituminous, bituminous, and anthracite toward the theoretical graphite end member. PHYSICAL PROPERTIES OF COAL The physical properties are concerned with the characteristics of coal in its natural state, or prior to its end use as a fuel. For example, the hardness and grindability of coal determine the maintenance cost for coal mining, handling, and pulverizing equipment; the specific gravity of coal and its associated minerals determines the coal preparation technique used in a cleaning plant as well as the capacity of coal bins, boats and size of cargo, and other coal storage facilities. The physical properties are, of course, dependent on the chemical constituents of coal, and all properties are interrelated. Specific Gravity The specific gravity (sp gr) of a solid is the ratio of the weight of a cubic foot of the solid to the weight of a cubic foot of water. The specific gravity of pure coal has been reported to range between 1.23 to 1.72 and increases with the change in rank from lignite to anthracite. This means that it is 1.23 to 1.72 times heavier than water.

Jan 1, 1981

By James C. M. Li

The thermodynamics of the set of functions including the activation enthalpy. the activation free energy, and the activation entropy for the motion of dislocations at low temperatures is formulated without a specific model or a mechanism. The behniiior near absolute zero of all these functions and of other relevant quantities related to dislocation mobility Is examined in the light of the third law of thermodynamics. The velocity measurements of Stein and Low for edge dislocations in Si-Fe are used .for illustrotion. In the plastic deformation of crystalline materials, a fundamental assumption, which is supported by direct measurements using etch-pit techniques,'-4 is that the average velocity of a certain mobile dislocation is a single-valued function of temperature and the effective shear stress exerted on the mobile dislocation: Sometimes under certain assumptions, even without direct dislocation-velocity measurements, an activation volume can be obtained from a change in strain rate in a simple tension test. Similarly an ac tivation enthalpy can be obtained by changing the temperature in a creep test. However, the assumptions involved should be studied carefully before using the results of these tests. Consider, for example, a tensile specimen at some stage of deformation with a distribution of mobile dislocations. Let the total length of dislocations of type i be pi per unit volume. The Burgers vector of these dislocations is hi which makes an angle ?i with the tensile axis. With respect to the same tensile axis, let the normal of the slip plane of these dislocations

Jan 1, 1965

In the history of American mining, so far as I know, there is no cleaner, brighter, or more completely successful mining adventure than that of the United Verde Extension.* It deserves to be placed on record here. The mine is at Jerome, 25 miles northeast of Prescott, in Yavapai county, Arizona. For 30 years before the U.V.X., as it is known to mining men, achieved celebrity, the Jerome district was identified with a copper mine, the United Verde, one of the great mines of the world. The success of this mine, of course, stimulated the search for similar orebodies, or for an extension of those already known, in adjacent ground; but, despite vigorous prospecting, the United Verde remained for many years alone in its glory. The reason for this solitariness was geologic: a fault with a big throw frustrated the effort to trace the ore-zone, thereby causing exploratory work to be both uncertain and costly. Despite these failures to develop other mines in the vicinity, the belief persisted that all the ore was not localized in the United Verde mine, but before we consider the reasons for such a belief we must look at the geologic conditions. The basal rock of the Jerome district is a schist, which has been correlated with the Yavapai formation of the Bradshaw quadrangle. This schist is geologically ancient, for it is of pre-Cambrian age. It is composed of volcanic tuffs, together with sediments, both argillaceous and siliceous, all of which

Jan 1, 1932

Joseph Esrey Johnson, Jr., had already achieved rare distinction as an able metallurgist, clear thinker, brilliant author, and wise consulting engineer to bankers and operators; he had achieved the essentials of a great career when death cut short his activities on Apr. 4, 1919, in the forty-ninth year of his age. He belonged to a family of iron blast-furnace men and mine managers. His father, Major J. E. Johnson, after serving with distinction in the Army of the North, identified himself with the iron mines and blast furnace at Longdale, Va., with which he was connected during almost his entire business life. It is significant that, during those troublous times of reconstruction in the South, he enjoyed always the affection and respect of his neighbors and associates alike. From him his son obtained not only a thorough training in blast-furnace practice and iron mining, but great personal courage and force of character. His mother, who survives both her husband and sons, possesses rare intellectuality, humor and a tenderness and human sympathy which those who were privileged to know well J. E. Johnson, Jr., recognized beneath his exterior of aggressiveness and will power. In a recently published analysis of the qualities which characterize the world's great men, three traits stand out preeminently; viz., independence, courage, and intellectuality. Each of these characteristics J. E. Johnson, Jr., possessed in extraordinary degree. His early education was obtained under a private tutor at Longdale, and this circumstance probably enhanced , a natural tendency to independence of character and individuality which, however, under the control of his

Jan 5, 1919

By J. C. Smock

THE magnetic iron ores of New Jersey are found in the northern part of the State, in the Highland Mountain range, which runs from the New York line on the northeast, to the Delaware River, near Easton, at the southwest. The same range continues across Orange County to the Hudson River, and towards the southwest it is known in Pennsylvania as the South Mountain. It is more properly an elevated table-land, quite deeply furrowed by several narrow, longitudinal valleys, and shorter cross-valleys or gaps. The ridges or lines of elevation, as well as the lower valleys, conform in their general direction very closely to the general trend of the whole belt or table-land, that is, from northeast to southwest. This also agrees with the prevailing strike of the rocks. This great uniformity in the altitudes of the hills and ridges, and the direction of the lines of depression corresponding to the strike of the strata, point to an original table-land, which, through the long action of denuding agents, has been quite deeply eroded, giving rise to the present surface configuration, so that some of the former and uniform features have been partially obliterated. The very few cross-valleys or depressions are much more irregular in their course, and serve as outlets through which the drainage is carried either into the Kittatinny Valley on the northwest, or to the broad, red shale and sandstone plane bounding the highlands on the southeast. The area of this highland

Jan 1, 1874

By J. C. Smock

The magnetic iron ores of New Jersey are found in the northern part of the State, in the Highland Mountain range, which runs from the New York line on the northeast, to the Delaware River, near Easton, at the southwest. The same range continues across Orange County to the Hudson River, and towards the southwest it is known in Pennsylvania as the South Mountain. It is more properly an elevated table-land, quite deeply furrowed by several narrow, longitudinal valleys, and shorter cross-valleys or gaps. The ridges or lines of elevation, as well as the lower valleys, conform in their general direction very closely to the general trend of the whole belt or table-land, that is, from northeast to southwest. This also agrees with the prevailing strike of the rocks. This great uniformity in the altitudes of the hills and ridges, and the direction of the lines of depression corresponding to the strike of the strata, point to an original table-land, which, through the long action of denuding agents, has been quite deeply eroded, giving rise to the present surface configuration, so that some of the former and uniform features have been partially obliterated. The very few cross-valleys or depressions are much more irregular in their course, and serve as outlets through which the drainage is carried either into the Kittatinny Valley on the northwest, or to the broad, red shale and sandstone plane bounding the highlands on the southeast. The area of this highland

By Geo. H. Ashley

THE present critical state of the supply, distribution, and utilization. of coal and the necessity for pooling and zoning coals calls renewed attention to the lack of any fully adequate classification of coal. In the past coals have been classified as anthracite, semianthracite, semibituminous, bituminous, subbituminous coals, and lignite, and a few special types, such as splint coal and cannel coal. But under the term bitumi¬nous coal are included a great variety of coals differing markedly both physically and chemically. The term subbituminous coal covers as great a range of chemical differences. In order to distinguish these varieties of bituminous coals it has been customary to designate coals by names derived from the place where mined, or by the name of the bed from which it is mined. Thus, in the market reports, coals are quoted as Pocahontas coal, New River or Sewell coal, Moshannon coal, Ohio coal, Williamson County coal, Jellico coal, and so on indefinitely, no limit being set as to the boundaries of the area to which a given name is applied. Nor is there any scale by, which the coal from one place may be compared with the coal from some other district or some other bed. On the one hand, coals from the same district may be quite distinct and sell at very different prices or coal from the same bed may differ greatly in different districts; on the other hand, coals from different states may be so similar physically and chemically that one could replace the other in practical use without any appreciable difference in service.

Jan 8, 1919

By R. O. Williams

The concept of biaxial pole figures which completely represent sheel textures is defined and an iterative least-squares solution given. The method has been applied to rolled copper, aluminum, and brass. The results show that the prior ideal textures are reasonably correct but incomplete. The major components in all three cases consist of a continuous range of orienta-tions roughly described as starting from (211) [111] continuing to (110) [112] to (110) [001], the details dif- THIS paper considers the problem of representing rolling textures in the most useful and comprehensible manner possible. A representation called a biaxial pole figure which completely represents such textures fering in all cases. For brass, in particular, the last part of the range is the most important. A minor cube component is established for the copper and aluminurn. The results were also analyzed by means of sets of three axial (inverse) pole figures to give similar, less-detailed results. The method of analysis is outlined. Such a representation is significantly less powerful than the biaxial method, but it has considerable utility in the calculation of anisotropic properties. is defined and an iterative least-squares solution is given. Such textures may be approximated by treating the principal directions as fiber axes to give three axial (inverse) pole figures. This representation is very useful for calculating anisotropic properties. New data for rolled copper, brass, and aluminum are given by both methods. In an axial pole figure the relative frequency or probability of a given physical direction (normally the

Jan 1, 1969

By Ira Joralemon

THE sampling of disseminated copper deposits has been described often but the method of combining assays, to give the true shape and value of the orebody as it will be mined has received less attention. As the ore mined during five or ten years at several of the great disseminated properties has averaged materially lower in grade than the published estimates, the question of the sampling and estimating of these orebodies seems timely. In this paper, attention is given particularly to factors that may cause errors in the final estimate. Sampling of diamond-drill holes, churn-drill holes, and underground workings is briefly described in the first part of the paper; then the method of combining assays to give the average grade and tonnage that will be mined is taken up in some detail. The necessity of study of the geology of the deposit and of probable costs is emphasized. Finally, the methods of calculating tonnages are outlined. DIAMOND-DRILL SAMPLING There are three main requisites for accurate diamond-drill sampling. First, the core should be removed and the hole cleaned out at the beginning of every sampling interval, usually 5 ft. (1.5 m.). After the rods are let down, water should be run through them until it becomes clear. The water must be clear before drilling starts. In this way the material knocked down from the sides of the hole by the descending rods is washed away, instead of being left to salt the sludge, sample.

Jan 2, 1922