Search Documents

By L. B. Davidson

The petroleum literature contains many reports on the relative permeability properties of porous media. However, only recently have studies of relative permeability at elevated temperatures been made.1 -5 Each of these studies presents relative permeability data on water-oil systems in linear sandpacks or sandstone cores under isothermal conditions. The results of these investigations are dissimilar. Edmondsonl found that in Berea sandstone a temperature-dependent effect was present, while Shilobod,2 using the same material, found no temperature dependence after normalizing for initial water saturation. Workers at Texas A&M U.3-5 found that the ratio kw/ko was temperature dependent in an unconsolidated system. The differences in results of these studies are probably a consequence of differences in the material employed, in the experimental procedures followed, and in the properties of the porous systems used. This paper describes an experimental investigation of permeability ratio temperature dependence, conducted to clarify some of the results obtained by previous workers. Each experiment described in this paper involved the isothermal displacement of Chevron No. 15 white oil by either nitrogen, steam, or distilled water and displacement of water by nitrogen. All permeability ratios were calculated using the Welge procedure. Values of the water-oil permeability ratio were obtained over the temperature range 75OF to 540°F. Results indicate the ratio is temperature dependent at low water saturations, probably due to interfacial effects. However, as the saturation is increased, temperature dependence decreases until, above some minimum saturation, the ratio becomes insensitive to temperature. Previously published work indicates that the dependence reappears at very high water saturations, a region of the ratio curve not completely examined in the present study. It appears that water-oil permeability ratios are temperature dependent at the extremes of the ratio curve where changes in interfacial tension with temperature induce variations in residual saturations. Between the extremes, there is a region in which the permeability ratio is insensitive to temperature. The size and location of this region is probably a function of the characteristics of the porous system. Gas-oil permeability ratios calculated from nitrogen-white oil displacement experiments indicate a definite temperature dependence over the range 75OF to 500°F and over the entire gas saturation range studied. Evidence discussed in this report indicates that this dependence is a consequence of molecular slippage in the gas phase. This is an extension of the Klinkenberg effect6 to two-phase systems at high temperatures (the existence of slippage in two-phase systems at room temperature has been demonstrated7). Evidence for a similar source of temperature dependence in superheated steam-white oil experiments

Jan 1, 1970

By H. J. de Haan, L. Schenk

Scope for Thermal Recovery in Shell's Heavy Oil Fields in Venezuela The main heavy oil reservoirs on the East coast of Lake Maracaibo (Fig. I), known as "Bolivar Coast", initially contained some 20 billion bbl of oil in place with gravities in the range of 10 to 15° API. The current total production rate is about 400,000 B/D. Since the recovery to date is on an average only 12.5 percent of the initial oil in place, these fields offer a vast potential for secondary recovery methods. The reservoirs are characterized by moderate depth (generally 1,000 to 3,000 ft; maximum 5,000 ft), good formation properties such as net oil sand thickness (50 to 300 ft), high porosity (30 to 40 percent) permeability (1 to 3 darcies) and oil saturation (initially about 80 percent) and high oil viscosity (100 to 10,000 cp in situ), all of which are favorable for the application of thermal recovery processes. Since 1957, steam drive, steam "soak" and underground combustion have been tested or are being tested in this area.1-3 This paper deals with a major steam drive test in the Tia Juana field. The test was commenced in Sept., 1961, on the basis of encouraging results of laboratory experiments and pilot field tests, which will be discussed briefly. Early Laboratory Investigation of the Steam Drive Process In 1956 a series of model experiments was carried out in the Koninklijke/Shell Laboratorium, Amster- dam, to investigate the displacement of heavy oil by steam.' The prototype studied was a horizontal, un-consolidated heavy oil reservoir, subjected to a linear steam drive. The model, representing a slab from this reservoir along the main flow direction, consisted of a steel tube filled with oil-saturated sand, provided with layers of rock at the top and bottom to simulate conductive heat losses to cap and base rock. Lateral heat losses, perpendicular to the main flow direction, were minimized by insulating the sides of the model. Heat flow and viscosity and gravity forces were scaled by taking the steam injection rate and sand permeability inversely proportional to the geometric reduction factor of the model, and using materials (oil, steam, cap rock, etc.) identical with those of the prototype. The main feature of the process was a frontal displacement mechanism that was observed within wide ranges of injection pressure and rate, oil viscosity, initial oil saturation and sand permeability. The high stability of this front can be attributed to the high volumetric steam flow rates, combined with the reduction in oil viscosity. High recoveries were obtained due to the low residual oil saturation of about 15 percent in the zone swept by steam. The latter value pertains to the specific test conditions (heavy oil, uncon-solidated sand) and may be lower for light oil, due to the effects of steam distillation. The applicability of this experimental approach is limited, as it does not take into account the fact that

Jan 1, 1970

By Neville J. Price

In order that the reader may not be misled, I feel it necessary to comment upon the title of this paper. "Laws of Rock Behavior," one may take as being part of the all-embracing "Law of Nature" and this, according to the Oxford Dictionary, relates to the principles of conduct recognized as being pleasing to God. I feel it would be presumptuous to erect a code of rock behavior on this basis, so turn to a secondary definition, namely that a "Law" is that which is intrinsically reasonable. It is extremely unlikely that any group of geologists, or workers in rock mechanics would be in complete agreement about what could be taken to be "intrinsically reasonable." Therefore, this paper does not present any deified utterances, but rather deals with a few aspects of rock behavior which I consider to be intrinsically reasonable and with which I hope the reader will concur. The mode of behavior of rocks in the Earth's crust covers the range from wholly brittle to completely ductile ; with a deformation time scale which may be measured in milliseconds, for some events such as meteoritic impact, or in millions of years for the tectonic deformation involved in mountain building. A complete survey is, of course, outside the scope of an introductory paper, so I must be both brief and selective in my treatment. Any attempt to establish the mode of rock behavior in the Earth's crust should take into account data and relationships established in laboratory experiments and correlate these with field evidence. Consequently, the first section of this paper presents a brief discussion of the experimental aspects of rock mechanics which are pertinent to the subsequent discussion.

Jan 1, 1970

By Shiou-Chuan Sun

DISCUSSION shiou-chuan sun (author's correction) - Too late for revision, the author realized that the data on stability of froth presented in this paper were not based on the same height of froth column. It is recommended herein that the stability of froth is better calculated by dividing the time elapsed until the froth disappeared by the volume (in cu cm per sq cm) or height of the froth column, and is expressed in sec per cm. The stability data in Tables I, II, and III of this paper were recalculated, in accordance with this recommendation, and the results are shown respectively in the accompanying Tables VII, VIII, and IX. Compared with Tables I, II, and III of the paper, the stability data of Tables VII, VIII, and IX are more reliable in disclosing the persistence of froth of various frothers having different frothabilities. For example, the conclusion given in the paper that the stability of froth is generally proportional to the volume of froth becomes invalid when the stability of froth is expressed in sec per cm, as shown in Tables VII, VIII, and IX. Table VII shows that both the stability and volume of froth increase with the addition of small amounts of n-hexyl alcohol, and that further additions of n-hexyl alcohol decrease the stability but increase the volume of froth. Table VIII indicates that the stability of different types of frothers is governed by their chemical composition and is difficult to predict from their frothability. Table IX shows that the stability of different frothers with similar nonpolar groups tends to increase with a decrease of the hydro- philic property of their polar groups, and consequently with the decrease of their solubilities. This is further substantiated by the fact that the stability of frothers, as listed in Table IX, is generally lowered by the solvent effect of absolute ethyl alcohol. Table IX shows also that the stability of froth tends to increase with the decrease of the volume of froth* provided the frothers used have similar nonpolar groups and dissimilar polar groups.

Jan 1, 1953

By Shiou-Chuan Sun

DISCUSSION shiou-chuan sun (author's correction) - Too late for revision, the author realized that the data on stability of froth presented in this paper were not based on the same height of froth column. It is recommended herein that the stability of froth is better calculated by dividing the time elapsed until the froth disappeared by the volume (in cu cm per sq cm) or height of the froth column, and is expressed in sec per cm. The stability data in Tables I, II, and III of this paper were recalculated, in accordance with this recommendation, and the results are shown respectively in the accompanying Tables VII, VIII, and IX. Compared with Tables I, II, and III of the paper, the stability data of Tables VII, VIII, and IX are more reliable in disclosing the persistence of froth of various frothers having different frothabilities. For example, the conclusion given in the paper that the stability of froth is generally proportional to the volume of froth becomes invalid when the stability of froth is expressed in sec per cm, as shown in Tables VII, VIII, and IX. Table VII shows that both the stability and volume of froth increase with the addition of small amounts of n-hexyl alcohol, and that further additions of n-hexyl alcohol decrease the stability but increase the volume of froth. Table VIII indicates that the stability of different types of frothers is governed by their chemical composition and is difficult to predict from their frothability. Table IX shows that the stability of different frothers with similar nonpolar groups tends to increase with a decrease of the hydro- philic property of their polar groups, and consequently with the decrease of their solubilities. This is further substantiated by the fact that the stability of frothers, as listed in Table IX, is generally lowered by the solvent effect of absolute ethyl alcohol. Table IX shows also that the stability of froth tends to increase with the decrease of the volume of froth* provided the frothers used have similar nonpolar groups and dissimilar polar groups.

Jan 1, 1953

By CHARLES R. KETES

I. INTRODUCTORY. Lake Valley, New Mexico, has long been one of the most widely known mining districts of southwestern United States. For many years its silver-mines have been among the most famous of the country, visited by many mining men and geologists; yet little information regarding the origin of the ore-deposits and the influencing geologic conditions has found its way into print. With the recent revival of public attention, after a decade and a half of utter stagnation, to the mining of silver in the Southwest, special interest attaches to the genesis and geologic disposition of the ore-bodies which are so finely open to inspection in the Lake Valley district. Moreover, the local features here described are typical of the conditions existing over a much larger field. The fact that the ores are chiefly the chloride and the chloro-bromide of silver adds further interest. Data bearing upon the genesis of haloid ore-deposits are, at the present time, very much sought. Arid regions offer particularly favorable conditions for the formation of such ores. This New Mexican district appears to supply solutions to many problems concerning this class of ores, which have long vexed the student of ore-deposits. II. LOCATION AND HISTORY. The town of Lake Valley is situated in Sierra county, in the southwestern part of New Mexico, and 100 miles northwest of El Paso, as the crow flies.From a mining standpoint, the location of the place is itself suggestive, as it lies on the southeastern slope of the great quaquaversal arch of the Colorado plateau. The center of this vast dome is in north-central Arizona, and radii about 150 miles in length reach its foot in all directions. Around its basal margins runs the broad mineralized belt containing most of the great mines of the Southwest, which extends from south-central Colorado southward and southwestward through New Mexico, thence westward through Arizona, northwestward and northward through southeastern California and western Nevada, and, finally, eastward through Nevada and Utah into Colorado again. This great mineralized belt is important as geographically limiting profitable mining over the greater part of five States.

Jan 1, 1908

By Robert Mehl

IN examining the progress of metallurgical science, the critic must remember that most of our present knowledge of metals and alloys has been accumulated through the needs of industry and commerce rather than through the desire and efforts of a large body of scientists interested primarily in developing a science of metals. The progress of metallurgy, scientifically speaking, has been irregular, and little given to the exhaus-tive exploitation of important scientific fields. The experienced engineer now recognizes the need for the development of the basic science upon which his engineering rests. In addition to the increase in knowledge which results from the normal requirements of industry, a development of the basic science of the behavior of metals and alloys is as desirable in metallurgy as in any other branch of science and engineering. The continued growth of the science of metals-as of every other science-requires studious attention to the principles that underlie the behavior of matter, with the result that knowledge in the several fields of interest should continue to increase. Among the various subjects recognized as important in physical metallurgy few have a wider significance than that of diffusion in solid metals. The phenomena of diffusion are intimately related to many basic problems of the metallic state, but in addition to this, the process of diffu-sion is of first importance practically. The formation of alloys by the annealing of mixed powders, first practiced by Faraday and Stodart81 in 1820 and in more recent years investigated by Masing187,189 and others, has led to the development of special alloys like Carboloy, Vascoloy-Ramet, Genelite, Elcon68, and has recently been applied to the production of noble-metal alloys for electrical contacts"'.

Jan 1, 1936

By R. D. Pehlke, J. V. Gluck

AS a portion of a general study of liquid-metal thermodynamics, high-temperature galvanic cells were used to study the effect of added dilute solutes on the activity of zinc in dilute solution with molten bismuth in the range 450° to 650°C. 1,2 The cells were of the type The experimental procedures have been described previously.1 In the course of studies conducted in the bismuth-rich corner of the systems Bi-Zn-Au and Bi-Zn-Cu, marked discontinuities were observed in the electromotive force-temperature relations for a number of the experimental compositions. Above the discontinuity temperatures, the relations, which were linear, exhibited slopes similar to the binary alloy of the same mole fraction zinc, as shown in Figs. I and 2. Below the discontinuity temperatures, the slopes were markedly different, but the relations remained linear. In general, as the amount of the third eletnent was increased, the slope of the lower portion of the relations tended to become less positive. The slopes of electromotive force-temperature relations reflect the entropy of mixing of zinc and, therefore, the occurrence of a discontinuity marks the transition between two different equilibrium situations involving the solution of zinc. A number of other investigators3-5 have used such observations to determine liquidus boundaries in binary alloys. Since the upper portions of the ternary electromotive force-temperature relations of this study had the same slopes as the binary alloys, the discontinuities are interpreted as marking the transition between the single-phase liquid region and the underlying two- and three-phase regions. Reference to the Zn-Bi equilibrium diagram6 confirms that the binary alloys were single-phase liquids at the experimental temperatures. Fig. I shows the electromotive force-temperature relations for the alloys containing Bi-Zn-Au and Fig. 2 shows similar relations for the Bi-Zn-Cu alloys. In the lower portion of each figure, the temperature of the discontinuity is plotted vs the mole fraction of the added solute at the various levels of zinc concentra- tion. Cross-plots from these curves at constant temperature permitted the construction of the partial liquidus surface isotherms shown in Figs. 3 and 4.

Jan 1, 1967

By S. W. Hazen

The use of operations research and computer techniques continued to expand during 1967. A number of mining companies either obtained computers or were experimenting with their use through service bureaus. This trend was also evident in the Canadian mining industry. Although the annual Symposium and Short Course on Computers and Operations Research in Mineral Industries was not held in 1967, technical periodicals like MINING ENGINEERING, Mining Congress Journal and Engineering and Mining Journal stepped up their coverage on the subject. The annual AIME meeting had eight papers in two sessions and one session on Operations Research was held at the SME Fall Meeting in Las Vegas.

Jan 2, 1968

By B. M. Burchfiel

CALIFORNIA possesses such an abundance of ceramic materials other than clays, that she is quite independent of other states and foreign countries so far as these materials are concerned. Certain users import some feldspar, silica, and allied minerals, but they do so from choice and not necessity. Production is largely for home consumption, so the total volume of ceramic materials produced is comparatively small. Many small deposits of the materials here under discussion are worked by individuals, and their output sold to individual grinding companies or users. The data given here shall be confined to the larger deposits and developments because they give a truer picture of typical deposits, operations, and materials.

Jan 1, 1936

By Frank C. Greene

Missouri has had one of the best years in history in the development of gas, the 49 completed gas wells having an average of nearly 1,000,000 cu. ft. initial open flow. Altogether 101 wells were drilled in the western part of the state, from Andrew County on the north to Vernon County on the south. Of these 49 were gas wells (including four old wells drilled deeper) with an initial open flow of 48,850,295 cu. ft., eight were oil wells (including one old well drilled deeper) with an initial capacity of 125 bbl. per day and 44 were dry holes (including five old wells drilled deeper). All the oil wells were in previously discovered pools in Jackson and Cass Counties. The outstanding discovery was a "shoestring" of a sand that is termed the Bartlesville, trending northwest and southeast across townships 48 and 49 N., R. 32 W., in central Jackson County. The sand is believed to be a narrow channel or bar, probably not over 800 ft. wide, lying at a higher horizon than the Bluejacket or true Bartlesville sand. A total of 32 wells with 47,453,080 cu. ft. initial open flow has been completed along the 6 miles of the shoestring. The largest individual well had an open flow of 4,500,000 cu. ft. The depth of these wells ranges from 350 to 635 ft., depending on surface elevation. The rock pressure ranges from 145 to 169 pounds. The Missouri Valley Gas and Oil Co. and Panhandle Eastern Pipe Line Co. have laid pipe lines into the area and most of the wells are now connected. In other parts of Jackson County and in other counties of the state there was very little activity during 1937. Of the 101 completions, 88 were in Jackson County. Cass County had five oil wells and three dry holes, Bates County one dry hole and Vernon County two dry holes. In the northern counties, Andrew and Clinton were represented by one dry hole each. At the end of 1937 drilling and leasing operations were very active and wildcatting promises to feature the coming year.

Jan 1, 1938

By Jorge Munoz Reyes, Guillermo

The new entity, Yacimientos Petroliferos Fiscales Bolivianos, created in 1936 for the development and exploitation of all petroliferous zones of Bolivia, including those formerly belonging to the Standard Oil Co., is doing its utmost to bring about rapid development and by this means to create a new source of revenue for the State. With this in view, Y.P.F.B. has opened a new field in the Samaipata region, on the main road between Cochabamba and Santa Cruz. Installation of machinery has begun for the drilling of several wells on the five anticlines that occur in this region. Work has also begun in the Saipuru field, on the Santa Cruz-Charagua highway, which was discovered by the Standard Oil and temporarily abandoned. In this new field, a topping plant will be installed, to supply gasoline and kerosene to Santa Cruz. Explorations are also being made on the neighboring structures of Saipuru. At the end of 1937, the committee that is to study the region of the Chapare in the northeastern part of Cochabamba, was organized. The structures were studied 10 years ago by Kirtley Mather and other geologists. It is hoped that by March 1938 this camp will begin work, as this zone gives promise of being valuable. Development The capacity of the refinery at Camiri has been enlarged in order that it may supply all the needs of that region. In order that the supply of crude may be adequate, several wells that had been almost abandoned by the Standard Oil are being cleaned out. New wells have been located at this camp following the principal anticlinal structure, and during the first half of the year 1938 several wells will be drilled. The same program is being followed in Sanandita but on a greater scale, as the nearness of this district to the Argentine border, which is the best market for the Bolivian petroleum of the south, allows immediate sale of the petroleum. Possibly a new refinery will be installed at this camp, as the one now in existence is only a rudimentary distillery. At the Bermejo camp, which is farther south, intensive work is being done to bring the wells into production. The Standard Oil produced limited quantities several years ago, but since 1927 the wells of this dis-

Jan 1, 1938

By H. Herbert Hughes

ECONOMISTS have predicted that the present business depression ultimately may pay big dividends to industry through the cumulative savings resulting from technical improvements and merchandising advances that might never have been developed under normal conditions. Waste prevention is a sound medicine for economic ills. In theory, this prescription may be applied not' only to raw materials, but also to labor, fuel, over- head, and other phases of production. Actually, how- ever, regardless of the efficiency of operating practices, waste is inevitable in the production of many commodities. The problem then becomes one of profitable utilization of waste rather than prevention.

Jan 1, 1932

By C. R. Austin

THE investigation described in this paper deals with the development of high-temperature alloys of the Konel series over a considerable period of time at the Research Laboratories of the Westinghouse Electric and Manufacturing Co. The word "Konel" has been coined to designate a class of alloys which are essentially nickel-cobalt-iron with other elements added, usually in small quantities. Most of these alloys contain titanium, usually about 2.5 percent. The main consideration related to strength at high temperatures but the thermionic characteristics of the alloys was also of considerable importance. It is, however, with the mechanical properties at elevated temperatures that we are herein concerned. Much attention has also been devoted to their age-hardening characteristics. There is little need to stress the utilitarian aspect of this subject, as it has been discussed frequently. Alloys exhibiting superior properties at normal or elevated temperatures rapidly find many suitable applications. There may be some question, however, as to what constitutes a "superior alloy, " or an alloy that may have good service possibilities at high temperatures. The problem is complex and various means have been employed to predict the useful life that may be expected of a material. In recent years the "creep limit" has been used as the best means of evaluation. Such tests necessarily are prolonged and hence collection of data is very slow. In a general survey of many alloys therefore the creep test is not desirable and recourse must be had to much shorter time tests in order more rapidly to select alloys which appear to show promise. For this reason the present survey has been made using the high-temperature tensile test and a bend' test developed by Howard Scott.1 In the tensile test the conditions have been standardized for all tests, so that values obtained are at least comparable, one alloy with another, although the absolute values recorded merely indicate the mechanical properties at the given temperature under a definite rate of loading.

Jan 1, 1931

By D. H. Newland

New York has a small but not insignificant place in the oil and natural gas industries of the United States. It has had a continuous record as an oil producer since 1872, with an aggregate yield of about 104,000,000 bbl. The reported output for 1935 was 4,237,000 bbl., a gain of more than 10 per cent for the year and a total that has been exceeded only in the early period of flush production half a century ago. The industry has been steadily building up since 1920 with the successful practice of the water drive, which has given a new lease of life to pools that had been practically drained of oil recoverable by pumping. An additional output of 2000 bbl. or more per acre is being procured by this method. Altogether the fields in New York State cover about 55,000 acres. Their limits are well defined and it is unlikely that they will be extended in the future, although there is some prospect of finding additional supplies by deeper drilling. The oil from New York is all classed as Pennsylvania grade, for which the recent price has been about $2.50 a barrel. It is refined at Olean, Wellsville and Bolivar, in the oil district, and partly in Pennsylvania refineries. Exploration for natural gas, outside of the established districts, was considerable during the year. Altogether 59 wells were drilled, distributed over 13 counties, of which 33 were listed as producers and 26 were dry. At the close of the year, 13 wells were in process of drilling. The 33 producing wells had a combined estimated flow of 278 million cubic feet per day. The best results were obtained from exploration in Allegany County, where out of eight wells drilled to the Oriskany sandstone five were successful and showed a combined open-flow capacity of 107 million cubic feet. The Oriskany sandstone was encountered at a depth of 4500 to 4900 ft. In Steuben County, next east of Allegany County, two out of seven wells to the Oriskany proved productive, and one of these, in the town of Greenwood, on the Watkins structure, was probably the largest that has so far been opened in the state, with a reported yield of 35 million a day. In the central part of New York interest was awakened by the activity shown in exploring for gas in the Trenton limestone, in Camden, Florence and Rome townships, Oneida

Jan 1, 1936

By D. H. Newland

New York has a small but not insignificant place in the oil and natural gas industries of the United States. It has had a continuous record as an oil producer since 1872, with an aggregate yield of about 104,000,000 bbl. The reported output for 1935 was 4,237,000 bbl., a gain of more than 10 per cent for the year and a total that has been exceeded only in the early period of flush production half a century ago. The industry has been steadily building up since 1920 with the successful practice of the water drive, which has given a new lease of life to pools that had been practically drained of oil recoverable by pumping. An additional output of 2000 bbl. or more per acre is being procured by this method. Altogether the fields in New York State cover about 55,000 acres. Their limits are well defined and it is unlikely that they will be extended in the future, although there is some prospect of finding additional supplies by deeper drilling. The oil from New York is all classed as Pennsylvania grade, for which the recent price has been about $2.50 a barrel. It is refined at Olean, Wellsville and Bolivar, in the oil district, and partly in Pennsylvania refineries. Exploration for natural gas, outside of the established districts, was considerable during the year. Altogether 59 wells were drilled, distributed over 13 counties, of which 33 were listed as producers and 26 were dry. At the close of the year, 13 wells were in process of drilling. The 33 producing wells had a combined estimated flow of 278 million cubic feet per day. The best results were obtained from exploration in Allegany County, where out of eight wells drilled to the Oriskany sandstone five were successful and showed a combined open-flow capacity of 107 million cubic feet. The Oriskany sandstone was encountered at a depth of 4500 to 4900 ft. In Steuben County, next east of Allegany County, two out of seven wells to the Oriskany proved productive, and one of these, in the town of Greenwood, on the Watkins structure, was probably the largest that has so far been opened in the state, with a reported yield of 35 million a day. In the central part of New York interest was awakened by the activity shown in exploring for gas in the Trenton limestone, in Camden, Florence and Rome townships, Oneida

Jan 1, 1936

By George W. Friesen

This paper presents the historical trend and de- fines the causes of drilling cost escalation in the Gulf of Mexico during the 1970's. The three major components of escalation are: 1) inflation, 2) supply-demand imbalance (demand pull) and 3) decreases in drilling efficiency. The decade was divided into three periods. During each period one component of escalation was responsible for most of the rise in costs. From 1970 through 1973 only inflation pushed costs upward. During 1974 and 1975 a supply- demand imbalance caused most of the escalation. Since 1975, decreases in drilling efficiency have produced the major component of escalation. During any one year or period of years, the sum of the three components will give the total escalation rate. The reasons why different components contribute more toward escalation during certain years than others are shown by following the timing of oil and gas price increases, the overall quality of the acreage offered each year in offshore lease sales and the resulting drilling activity.

Jan 1, 1982

By P. A. Robbins

FAR NORTH, on the bare Arctic tundra, 11 mi. above the mouth of the Keewalik River where the latter discharges into Kotzebue Sound. several ., Eskimos garbed in parkies and muck lucks mingle with a small group of similarly clad white men. All of them shield their eyes from the white glare of the arc as a gasoline-driven arc-welding set rains molecules of metal on the break in a bull wheel, the large gear wheel which swings the boom and cab of a dragline shovel.

Jan 1, 1937

By K. P. Fournier

This report describes work on the problem of predicting oil recovery from a reservoir into which water is injected at a temperature higher than the reservoir temperature, taking into account effects of vis cosity-ratio reduction, heat loss and thermal expansion. It includes the derivation of the equations involved, the finite difference equations used to solve the partial differential equation which models the system, and the results obtained using the IBM 1620 and 7090-1401 computers. Figures and tables show present results of this study of recovery as a function of reservoir thickness and injection rate. For a possible reservoir hot water flood in which 1,000 BWPD at 250F are injected, an additional 5 per cent recovery of oil in place in a swept 1,000-ft-radius reservoir is predicted after injection of one pore volume of water. INTRODUCTION The problem of predicting oil recovery from the injection of hot water has been discussed by several researchers. l-6,19 In no case has the problem of predicting heat losses been rigorously incorporated into the recovery and displacement calculation problem. Willman et al. describe an approximate method of such treatment. 1 The calculation of heat losses in a reservoir and the corresponding temperature distribution while injecting a hot fluid has been attempted by several authors.7'8 In this report a method is presented to numerically predict the oil displacement by hot water in a radial system, taking into account the heat losses to adjacent strata, changes in viscosity ratio with temperature and the thermal-expansion effect for both oil and water. DERIVATION OF BASIC EQUATIONS We start with the familiar Buckley-Leverettg equation for a radial system:* This is sometimes referred to as the Lagrangian form of the displacement equation. If the injection water is at some temperature Ti which is above reservoir temperature TR, then lw, the flowing fraction which is water, is a function of both water saturation and fluid temperature at any given time and position in the reservoir. The temperature dependence of lw results from the temperature dependence of the viscosity ratio µo/µm of which lw is a function. Thus:

Jan 1, 1966

By B. N. Das, P. A. Beck

THE o phases have a complex tetragonal structure with Lo/ao = 0.52 and 30 atoms per unit cell.1 A large number of such phases are now known to occur in various binary systems of the transition elements and they exhibit the following typical features: 2,3 The composition of binary o phases is variable, ranging from approximately A4B to ABI. With only a few exceptions, in the o phases the A-ele-ment comes from the V- or Cr- group of the periodic table, while the B-elements are from the Mn-, Fe-, Co-, or Ni- group. In the first long period the corresponding o phases of the V- and Cr-series have approximately the same compositions. However, as the B-element changes from Mn to Fe to Co to Ni, the mean composition shifts monotonously toward higher A-contents.2-4 For example, if the mean compositions of the various o phases with vanadium are compared with each other, the composition shift mentioned above becomes plainly visible: V 30Mn0 80 Vo.45Feo..,, Vo .,Coo. 45 and Vo.5Nio.3. Similiar composition shifts, although not the same composition values, were observed in u phases formed by second and by third long-period transition elements.3'4 This behavior, very characteristic of o phases, is in rather sharp contrast to the usually quite well-behaved stoichi-ometry of the Laves phases. In the latter, the AB2 stoichiometry predominates, with A the large atom and B the small atom.= The p phase occurs in the four binary systems of Mo or W with Fe or Co. On the basis of their crystal structure determination, Arnfelt and westgren6 ascribed to the p phase in the Co-W system the ideal composition W,Co7. Since all four binary pphases have nearly the same composition, it would seem quite plausible that some definite stoichiometry such as A6B7, might be characteristic of this phase, as AB2 is of the Laves phases. On the other hand, it has been noted,7 that the phases occur at average electron concentrations near to those at which the various cr phases are found. Also, it has been pointed out by Shoemaker and associates8 that structurally the a phases and the p phases are somewhat related to each other; both of these structures may be described in terms of suitable stackings of quasi-hexagonal layers'of atoms. By studying a suitably chosen ter- nary phase diagram, one might expect to be able to find out which one of the two conditions, the analogy with the o phase or the constant ratio between the number of large atoms and the number of small atoms in effect governs the behavior of the p phase. Several isothermal sections of ternary systems containing o phases have been investigated. In all cases where two binary o phases occur, these were found to be connected b a more or less straight ternary o phase field.7' '10 Such elongated o phase fields were also found in ternary systems in which only one of the limiting binaries is known to contain o phase. In this manner a latent o forming tendency could be detected and the virtual composition of a "binary o phase", which does not actually occur as such was approximately determined by extrapolation. The behavior of the phases, including their composition shift, is analogous to that of the classical electron compounds, as described by Hume-Rothery.11 In order to decide whether the p phase is essentially a "size compound" like the Laves phases, where a fixed stoichiometric ratio is quite generally maintained between the "large atoms" and the "small atoms", or whether the p phase is typically an "electron compound" in the same sense as ois, it was decided to investigate an isothermal section of the Mo-Mn-Co system. The Mo-Co system12 and the Mo-Mn system13 each are known to have a binary o phase. It could be therefore expected that a ternary o phase field will connect these two binary cr-phase fields. The p phase is known to occur in the Mo-Co system. If the p phase should turn out to form an elongated phase field extending deep into the ternary system, the following considerations mighto apply. The atomic radius of manganese (1.314for C.N.12) is between the va,lues for Mo (1.40Afor C.N.12) and for Co (1.26Afor C.N.12). If it is assumed that p is a "size compound", and that Mn is substituting for the smaller Co atoms in the p-structure in the ternary system, the y-phase field might be expected to extend parallel to the Mn-Co binary line. If Mn is substituting for the large Mo atoms in the p-structure, the p-phase field may be expected to extend parallel to the Mn-Mo binary line. On the other hand, if the p-phase turns out to be an "electron compound" like o, the ternary p-phase field should extend parallel to the ternary o -phase field connecting (Mo,Mn)owith (Mo, Co) a

Jan 1, 1961