Search Documents

By John D. Sullivan, Edwin J. Rogers, Chester R. Austin

THE problem of making a building unit combining the necessary physical and mechanical properties and good thermal insulation has been foremost in the minds of architects and ceramic and construction engineers for many years. This paper presents the results of studies on thermally expanding shales or clays to produce light-weight cellular products suitable for making building units. An expanded clay block suitable for building purposes should be large enough so that substantial savings may be effected in labor costs in laying the wall. The permeability should be low and it should have sufficiently good "dry-wall" characteristics to permit exposing the exterior surface to the elements, and to permit plastering directly the inside wall surface. The thermal conductivity should be low and the mechanical properties should be adequate. Obviously, a unit possessing satisfactory qualities for constructing an outside wall would be satisfactory for interior walls and for back-up purposes. The results of studies on bloating various shales or clays† and the properties of the expanded products are reported. In another paper1 basic factors involved in bloating of clays are discussed. Manufacturers of ceramic products, particularly structural clay, may encounter bloating of the ware during burning, and precautions must be followed to avoid this phenomenon. About 1927 the C. F. Burgess Laboratories, Madison, Wis., while carrying on an investigation for the American Face Brick Research Corporation, conceived the idea of intentionally bloating clay while holding it in a restrained condition, with the hope of producing a unitary cellular mass. Work was carried on until about 1931, when studies were terminated because of business conditions. These studies were continued later by The Western Brick Co., Danville, Ill., which developed a process of "inwardly expansive bloating." The major purpose of the latter investigation was to produce back-up tile to compete with concrete blocks made from Haydite or cinder aggregate. Haydite is a light-weight aggregate formed by heating certain clays or shales rapidly in a rotary kiln. While the investigations at the C. F. Burgess Laboratories or at Western Brick Co. were not carried far enough to lead to the commercial production of material for the construction of walls, particularly outside walls, they showed that certain clays could be thermally expanded and that it was possible to produce a material of low permeability with a large percentage of the total voids or cells closed. Commencing in 1939, the Ozark Chemical Co. sponsored a research program at Battelle Memorial Institute for the purpose of determining whether it is technically feasible to make thermally expanded building units, and specifically to get answers to the following questions:

Jan 1, 1942

By R. B. Adamson

The fatigue behauior of irradiated copper single crystals is compared to that of unirradiated crystals. Proton or electron irradiation did not substantially change the fatigue-lzj.e, fatigue-hardening-, or slip-line characteristics, while neutron irradiation did appear to alter these parameters. Postfatigue transrrzission electron microscopy did not reveal any marked structural differazces between irradiated and unirradiated specimens. Possible dislocatio~a mechanisnzs to explain the observed behavior are discussed. A LTHOUGH considerable work has been done to ascertain the effects of radiation on the tensile properties of metals (e.g., Refs. 1 and 2), little work of a basic nature has been reported on the effect of radiation on fatigue properties. Since it is known that fatigue properties are sensitive to conditions at the surface of the metal, it was felt that charged particle irradiation, whose penetration into metals is very small, might influence the fatigue behavior. To investigate this surface effect, irradiations with 10 mev protons and 1.5 mev electrons were conducted. The range of 10 mev protons in copper is about 0.236 mm; which is very small compared with the thickness of the specimens used (1.53 mm). The range of 1.5 mev electrons is somewhat larger, on the order of 0.665 mm.4 On the other hand, irradiation with reactor neutrons produces damage throughout the entire specimen, so neutron irradiation can be used to study the effects of bulk damage. The damage introduced by proton and neutron irradiation is expected to con!ist of large interstitial dislocation loops,5 tiny (<25A) vacancy loops," and/or various vacancy-rich regions called depleted zones.&apos; In the case of electron irradiation at about -173°C the damage is expected to consist of isolated Frenkel pairs.&apos; The effect of radiation damage on the fatigue properties of some engineering materials has been reported,g,10 but the results are not clear-cut or consistent. SPECIMEN PREPARATION Zone-refined copper was used to grow single crystals by a modified Bridgeman technique in an inert helium atmosphere. Using a seeding method, single crystals were obtained as bars about 6 in. long with a cross section of 3 by $ in. Immediately upon removal from the split-mold graphite boat in which they were grown, the very soft bars were embedded in a room-temperature setting plastic. They could then be cut into specimen lengths without introducing any long-range damage. Generally, four or five specimens plus one seed were obtained from each bar. The plastic material was dissolved away in acetone and the orientation of each sample was checked by the standard Laue X-ray

Jan 1, 1968

By J. R. Long, E. T. Hayes, D. C. Root, R. S. Dean

THE U. S. Bureau of Mines has recently reported on the development of a process for preparing pure ductile titanium in substantial quantities&apos; and on the physical properties that may be attained in the metal, when consolidated by powder metallurgy methods and fabricated by certain hot and cold-working procedures.2 The high physical properties (Table I), combined with excellent corrosion resistance and light weight, will lead no doubt to appropriate applications of the metal. In any application, methods of joining will be of considerable importance. The relatively high activity of the metal toward the common gases raises the question of weldability and conditions that might be required for successful welding. Since hydrogen, oxygen, and nitrogen embrittle the metal, it should be protected from these gases at elevated temperatures. This was demonstrated by a few preliminary trials of arc, gas, and resistance welding. In these trials only the resistance method proved to be immediately applicable. While atomic hydrogen welding of titanium may be successful in some instances, a considerable amount of development work will be required to prove its worth. In addition, it would be suited only to small assemblies that could be heated subsequently in a high vacuum to remove embrittling hydrogen. Heli-arc methods likewise would be limited to small assemblies, which could be completely protected by a helium atmosphere. It was quite apparent that titanium required more protection than was afforded by the normal flow of helium gas used for welding magnesium and aluminum. The hot metal is attacked by oxygen and nitrogen, and the rapid diffusion of the oxide into the metal prevents the formation of a protective coating and requires the helium atmosphere to be maintained until the weld has cooled nearly to room temperature. The preliminary work indicated that titanium could be successfully spot-welded without deterioration of the metal and that the microstructures of the welds were normal, exhibiting good bonding, and no oxidation. The high resistivity of titanium (53 microhms per cu. cm.) suggested that it would behave somewhat like stainless steel and allow considerable latitude in the several welding variables. The results reported here are intended to give a general picture of the effects of varying welding current, welding time, and tip pressure on single spot welds made on several different thicknesses of titanium sheet. The work was undertaken to demonstrate the feasibility of welding titanium rather than as an exhaustive study of spot welding. There are, therefore, a number of factors that will require further investigation to establish the specific controls required for actual applications.

Jan 1, 1946

By G. E. Agar, P. L. De Bruyn

Flotation is an important example of a chemical process by which one solid may be separated from other solids in a mixture. In contrast to other chemical processes such as leaching and smelting, separation of solids by flotation is characterized by the establishment of contact among three phases. In froth flotation these three phases are the solid to be floated, an aqueous electrolyte solution, and a gas, usually air. The gaseous phase may be re- placed by an organic liquid phase or this organic liquid phase may be added deliberately as a fourth phase. To gain an understanding of the flotation sys- tem, it is therefore necessary to study the chemical and physical properties of surfaces and to establish the effect of changes in composition of the bulk phases on the nature of the three interfaces, solid-gas, solid-liquid and liquid- gas. With very few exceptions inorganic solids are completely wetted by the aqueous phase so that the first step in flotation is to replace partially the solid-liquid interface by a solid-gas interface. This displacement process is accomplished by the addition of suitable reagents to the aqueous phase. The resultant surface reaction leaves the solid surface with a hydrophobic film. Although the primary objective of these reagent additions is to alter the solid surface, chemical reactions between the added chemical species and those species derived from the dissolution of the solids are unavoidable. For a quantitative description of such reactions and for the determination of the feasibility of a proposed reaction, we rely on available thermodynamic data. The application of thermodynamic principles to flotation systems has contributed much to our understanding of flotation. The changes in thermodynamic properties such as free energy and chemical potential are accessible to experimental determination, and a knowledge of their magnitude allows us to develop and predict a chemical mechanism oy which a solid becomes floatable. In this chapter it will be assumed that the reader has a working knowledge of the general principles of thermodynamics and solution chemistry. A complete discussion of the physical chemistry of flotation must include a treatment of solubility relations, complex ionic equilibria, reaction potential, and the elements of electrochemistry, especially those dealing with reversible electrical cells. The principles related to all of these features of the flotation system will not be discussed in this chapter. The discussion will be concerned with the thermodynamics and electrochemistry of surfaces and the electrical double layer model of the interface.

Jan 1, 1962

By N. Tiner

The mechanical properties of magnesium-alloy castings are greatly improved by grain refinement, and at present considerable attention is being paid to methods of obtaining fine-grained castings. One method of achieving this end is the use of proper melting and superheating techniques. These have been employed com-rnercially to a great extent, but no comprehensive study of the subject appears to have been published at present. Numerous investigations found in the literature include some reference to superheating techniques,1"4 and Achenbach, Nippcr and Piwowarsky,% ased principally on thermal analysis, ascribe the grain-refilling action of superheating to the influence of solid foreign particles or dissolved gases present in the melt upon the course of crystallization. The primary purpose of this paper is to present the principal facts concerning the cffect of superheating on grain size of magilesium alloys. .ittempts are also made to explain the experimental results in terms of a general hypothesis. The investigations are limited chiefly to common commercial casting alloys. In order to carry on this work, it was necessary to determine the factors influencing grain size and to develop a proper technique for the preparation of samples. Thc preliminary tests made by the author indicated that the grain size of magnesium alloys resulting from the solidification of a melt is determined by alloy composition, presence of impurities, rate of cooling during solidification, thermal history of the melt and to some extent the structure of the charge used. The rate of cooling is in turn dependent upon the mass of the melt, pouring temperature, and dimensions, properties and temperature of the mold into which the melt is poured. The final grain size of the alloys is still further modified by heat-treatment subsequent to casting. It is not within the scope of the present paper to discuss all of these factors, and it would suffice to note here that when equal amounts of magnesium alloys are prepared from the same alloying materials, melted in graphite crucibles under the same thermal conditions, then cast into graphite molds at a constant temperature, the resultant solids have the same grain size. By maintaining all other factors constant, it is thus possible to vary thermal conditions of a melt and to examine the grain size of resultant castings. Preparation of Samples and Grain-size TestiNg The alloys investigated in this paper were taken from ingots made by Permanente the Or or prepared by the author with pure carbothermic magnesium and necessary alloying elements. Melting was carried out under a flux in a graphite crucible heated uniformly by an

Jan 1, 1946

By N. Tiner

The mechanical properties of magnesium-alloy castings are greatly improved by grain refinement, and at present considerable attention is being paid to methods of obtaining fine-grained castings. One method of achieving this end is the use of proper melting and superheating techniques. These have been employed com-rnercially to a great extent, but no comprehensive study of the subject appears to have been published at present. Numerous investigations found in the literature include some reference to superheating techniques,1"4 and Achenbach, Nippcr and Piwowarsky,% ased principally on thermal analysis, ascribe the grain-refilling action of superheating to the influence of solid foreign particles or dissolved gases present in the melt upon the course of crystallization. The primary purpose of this paper is to present the principal facts concerning the cffect of superheating on grain size of magilesium alloys. .ittempts are also made to explain the experimental results in terms of a general hypothesis. The investigations are limited chiefly to common commercial casting alloys. In order to carry on this work, it was necessary to determine the factors influencing grain size and to develop a proper technique for the preparation of samples. Thc preliminary tests made by the author indicated that the grain size of magnesium alloys resulting from the solidification of a melt is determined by alloy composition, presence of impurities, rate of cooling during solidification, thermal history of the melt and to some extent the structure of the charge used. The rate of cooling is in turn dependent upon the mass of the melt, pouring temperature, and dimensions, properties and temperature of the mold into which the melt is poured. The final grain size of the alloys is still further modified by heat-treatment subsequent to casting. It is not within the scope of the present paper to discuss all of these factors, and it would suffice to note here that when equal amounts of magnesium alloys are prepared from the same alloying materials, melted in graphite crucibles under the same thermal conditions, then cast into graphite molds at a constant temperature, the resultant solids have the same grain size. By maintaining all other factors constant, it is thus possible to vary thermal conditions of a melt and to examine the grain size of resultant castings. Preparation of Samples and Grain-size TestiNg The alloys investigated in this paper were taken from ingots made by Permanente the Or or prepared by the author with pure carbothermic magnesium and necessary alloying elements. Melting was carried out under a flux in a graphite crucible heated uniformly by an

Jan 1, 1946

By W. O. Philbrook, R. H. Spitzer, F. S. Manning

A generalized mathematical model has been developed to describe the kinetics of the gaseous, topo-chemical reduction of porous hematite spheres. Gas-solid reduction is permitted at each of three advancing interfaces and is controlled by a complex series-parallel sequence of chemical and transport steps. Despite the fact that transport resistances are significant to the advance of each interface, little deviation from linear advance is predicted for the first 98 pct of reduction. Calculations to predict the movement of magnetite /wustite interface by a solid-state diffusion mechanism have been incorporated into the earlier dense-pellet model.&apos; The porous-pellet model is found to give a better description than the dense-pellet one for McKewan&apos;s measurements2 of interface movements in dense polycrystalline hematite reduced in hydrogen-water vapor mixtures. THIS paper reports a continuation of work"3" directed toward the better understanding of gas-solid reactions and the development of mathematical models that may be helpful in the design or control of ore-reduction processes. Laboratory studies of the reduction of single oxide samples in tube furnaces normally employ an abundant excess of pure reducing gas. Reduction may appear to be adequately described by a model assuming gas-solid reaction solely at the iron/wustite interface.&apos;&apos;&apos; However, when iron ore is reduced in either a fixed bed or an efficiently operated counter-current column, there are portions of the bed where the partially spent gas is no longer capable of reducing wustite to iron. Nevertheless, the formation of the intermediate reaction products, wustite or magnetite, can and does continue. In order to account for this aspect of the reduction of beds of particles, three semiempirical mathematical models were devised.&apos; One of these was for the limiting case of completely dense particles, and two alternatives were provided for porous particles. For purposes of the analysis, a dense pellet was defined as one in which the wustite and magnetite layers were impervious to the reducing gas when the atmosphere was capable of forming iron. In a porous pellet, the intermediate product layers were assumed to be sufficiently permeable to allow reducing gas to penetrate beyond the iron/wustite interface to form wustite and magnetite by removal of oxygen as a gaseous product rather than by a solid-state redfiction mechanism. Further progress required a better understanding of the reaction of the individual particles with the gas stream. A comprehensive mathematical treatment was developed&apos; to describe the continually changing interplay of transport and reaction steps

Jan 1, 1967

By N. Tiner

THE mechanical properties of magnesium-alloy castings are greatly improved by grain refinement, and at present considerable attention is being paid to methods of obtaining fine-grained castings. One method of achieving this end is the use of proper melting and superheating techniques. These have been employed commercially to a great extent, but no comprehensive study of the subject appears to have been published at present. Numerous investigations found in the literature include some reference to superheating techniques, 1-4 and Achenbach, Nipper and Piwowarsky,5 based principally on thermal analysis, ascribe the grain-refining action of superheating to the influence of solid foreign particles or dissolved gases present in the melt upon the course of crystallization. The primary purpose of this paper is to present the principal facts concerning the effect of superheating on grain size of magnesium alloys. Attempts are also made to explain the experimental results in terms of a general hypothesis. The investigations are limited chiefly to common commercial casting alloys. In order to carry on this work, it was necessary to determine the factors influencing grain size and to develop a proper technique for the preparation of samples. The preliminary tests made by the author indicated that the grain size of magnesium alloys resulting from the solidification of a melt is determined by alloy composition, presence of impurities, rate of cooling during solidification, thermal history of the melt and to some extent the structure of the charge used. The rate of cooling is in turn dependent upon the mass of the melt, pouring temperature, and dimensions, properties and temperature of the mold into which the melt is poured. The final grain size of the alloys is still further modified by heat-treatment subsequent to casting. It is not within the scope of the present paper to discuss all of these factors, and it would suffice to note here that when equal amounts of magnesium alloys are prepared from the same alloying materials, melted in graphite crucibles under the same thermal conditions, then cast into graphite molds at a constant temperature, the .resultant solids have the same grain size. By maintaining all other factors constant, it is thus possible to vary thermal conditions of a melt and to examine the grain size of resultant castings. PREPARATION OF SAMPLES AND GRAIN-SIZE TESTING The alloys investigated in this paper were taken from ingots made by Permanente Metals Corporation or prepared by the author with pure carbothermic magnesium and necessary alloying elements. Melting was carried out under a flux in a graphite crucible heated uniformly by an

Jan 1, 1945

F. AT. FARMER*, New York (written discussion?)- The paper presents many phases of the welding art concerning which there are very divergent views. In many cases, the wide differences of opinion are based on the results of mechanical tests, but an examination of the mechanical test data discloses a wide variation in character of the tests made and in the details of procedure, so that it is frequently not only difficult to analyze and check the basis of the conclusions but impossible to correlate various groups of test results. It would seem, therefore, that the technique of testing welds is one of the phases of the welding art that should be studied and standardized in order that the results of mechanical tests made by different people may be strictly comparable and have the same significance to all. The vital difference between testing a specimen of steel that includes a welded joint and testing an ordinary specimen is the non-homogeneity of the weld specimen. The weld specimen has at its center a section composed of material that usually has physical, chemical, and metallurgical characteristics distinctly different from the adjoining metal. Furthermore, the section of added metal is more or less irregular and the ratio of added metal to original metal in the section is quite variable. Consequently the details of procedure and of recording data should be more minutely prescribed than in the testing of ordinary specimens. A conspicuous example f a mechanical test that requires standardization is the cold bending test, a standard test for mild steel. With the usual method, the specimen is bent around. a pin of prescribed diameter and, as all specifications usually require bending to 180° without fracture, the manner of applying the load is immaterial because the specimen is ultimately completely wrapped around the pin. But a specimen containing a welded joint at the center will usually not withstand bending to 180° because of the much lower ductility of the deposited metal in the weld. It is therefore obvious that the farther apart the points of support are the greater will be the angle attained before cracking occurs, simply because most of the bending will take place in the original metal. It is therefore highly desirable that there be prescribed a standard test that fixes exactly the distance between the supports, the curvature of the surface of supports, and the relation between this curvature, that of the loading surface, and the thickness of the specimen.

Jan 5, 1919

By J. T., Norton

As cold working is an important feature in a great many of the fabricating processes now applied, this paper presents some ideas on the nature and results of the plastic deformation produced in this operation. The art of manufacturing metal for practical uses is very old and has undergone very great development. The science of metals has- also developed very rapidly recently and the various processes to which metals are submitted are much better understood now than they were even a short time ago. All the knowledge that can be obtained on this subject is useful because it promotes efficiency in converting metal into finished articles.

Jan 1, 1927

By Henry G. Morris

The use of compressed air for the transmission of power has reached so great a development that we find numerous large establishments devoted to the manufacture of machinery for its production and application, and special periodicals published for the dissemination of information on the subject. Moreover, its employment is so general in mining operations that no apology is needed for the presentation to the Institute of such a paper as the present. The admirable articles of Mr. E. A. Rix, published in Conzpressed Air, show a wide range in the mechanical efficiency of air-compressors, varying, under different conditions, from 15 to 60 per cent.; and it is evident that any

Jan 1, 1902

By G. B. Gould

FROM the very inception of the price-control experiment in the bituminous-coal industry, the problem of price differentials was of major importance. In fact, assuming that there will be no legal or Govern- mental obstacles to price control, the successful maintenance of the present or any other method designed to control bituminous-coal prices will depend upon the discovery of some satisfactory way to determine these differentials in price, among: individual mines and groups of mines. Being of organic origin, bituminous coal is a commodity that presents an almost infinite variety of qualities. It is inevitable, therefore, that a work- able price-control system must attempt

Jan 1, 1935

By L. E. PORTNER

INCREASING military demands on the petroleum industry have brought into bold relief the crude-oil reserves now available to meet combined military and civilian demands, emphasizing the necessity for a greater efficiency in recovery from what has been discovered than ever before, particularly in light of the absence of new discoveries. This situation-and the fact that the industry, as well as members of the Government charged with governing oil production, desire to meet all crude-oil demands made of the industry with the least loss in tangible reserves through production practices-paves the way for increasing application of sound principles of production engineering and conservation.

Jan 1, 1944

By Gilbert E. Doan

IN a technical civilization, that is. one whose major difference from past civilizations is its enormous development of technology, in transportation, communication, labor saving, centralized control, and mass production, it is natural that the most critical problems should be those that arise out of technologic advances; it is natural also that a. man who understands these advances should be chosen as the leader to meet these problems. This was done in the selection of Herbert Hoover as President of the United States. Mr. Hoover was a good, and perhaps a great President. But he was not a great politician and that ensured his defeat when a crisis came.

Jan 1, 1939

By AIME AIME

I would like to ask Bob Merrill whether he considers that horizontal concave curvature of a slope has any stabilizing effect, such as Jenike 1 suggested several years ago. The stabilizing effect is due to the restraint offered to radial movement by the curvature. We found in laboratory tests that if we constrained the rock with the same stresses as those measured in the pit then it would sustain a maximum stress about two or four times greater than when the same rock type was unconstrained. We are therefore definitely of the opinion that a constrained situation in a slope is favorable towards stability.

Jan 1, 1967

By AIME AIME

MECHANIZATION of operations and the development of much more refined preparation practices have been conspicuous achievements in coal-mine engineering in the last two decades. To both, Paul Weir was an outstanding contributor during his seventeen years&apos; service with the Bell & Zoller Coal & Mining Co. and its aliates, the Centralia Coal Co. and the Crescent Mining Co. From 1920 to the end of 1936, when he resigned to go into consulting work in Chicago, he was successively chief engineer, general superintendent, and vice-president of Bell & Zoller. He changed its Zeigler mines from hand to mechanical loading, and planned and built a central mechanical cleaning plant.

Jan 1, 1939

By AIME AIME

AMERICAN INSTITUTE OF MINING ENGINEERS. Vii MEMBERS&apos; PRIVATE RECEPTION ROOM. A separate room in the suite occupied by the American Institute of Mining Engineers on the ninth floor of the United Engineering Society Building, has been equipped with furniture and telephone extension for the use of members of the Institute who desire temporary private office accommodations. In order that the benefit of this arrangement shall not be restricted to a few members only, the length of time of continued occupancy is limited, and applications will be considered in the order of their receipt. A small fee will be required for the use of this room.

Jan 9, 1907

By Harold V. Pearce

The fire which occurred in the fall of 1906, at the works of the Boston & Colorado Smelting Co., Argo, Colo., destroyed entirely the gold- and silver-refinery of the plant, and in view of the development of modern practice in the refining of copper-mattes, etc., the management decided that it would be inadvisable to rebuild that part of the works for the continued use of the process which had been conducted therein for so many years as a metallurgical secret. This decision probably removes altogether from the sphere of practice the &apos;(Pearce" method for the separation of gold. At all events, it removes the busi-

Jan 1, 1909

By R. P. Killmeyer, B. S. Gottfried, J. T. Wizzard

The US Department of Energy&apos;s Coal Preparation Branch has developed a computer program to calculate the performance characteristics of coal washing devices. This program uses specific gravity analyses of the clean coal and refuse streams as input, and generates dependent and independent performance criteria for the washer. Partition curves are internally represented in a functional form by a Weibull function. Comparisons are made between performance criteria calculated by hand and the performance criteria calculated by the program for 120 different dense medium cyclone tests. Results show that the computer program gives results in close agreement with hand-calculated values while greatly reducing the amount of time involved in performing the analyses.

Jan 1, 1984

By R. R. Klimpel Discussion by C. C. Harris, L. G. Austin

C. C. Harris (Columbia University) — The authors &apos; have presented relationships for the random division of a magnitude into r + l parts taking account of the order of selection. Interpreting their model in comminution terms, their Eqs. 7, 9 and 11 refer to the one-dimensional case; that is, to the subdivision of a long thin rod at random. It is assumed that the fragments may be indefinitely small. Real materials, however, are limited in the degree of subdivision which can be attained through the intervention of practical restrictions. One in fine grinding is the depletion of microflaws as material becomes finer. Another is the

Jan 1, 1969