Search Documents

By John Jermain Porter

PAGE. I. INtroduction............ 191 I1. Derivation of Formula foR Fuel-RequiRements.... 192 1. Heat Available in the Hearth........193 a. Method of Calculation..193 b. Data for the Determination of Critical Temperature.. 195 2. Heat Necessary in the Hearth ...... 197 a. To Care for Slag..197 b. To Care for Pig-Iron...198 c. To Reduce Silicon........198 d. For Other Items.........199 3. The Effects of Rate of Driving ..... 199 4. Loss of Carbon Between Throat and Hearth.....201 a. Solubility of Coke..201 b. Carbon-Loss Due to Flux....201 c. Effects of Reducibility of Ore..202 5. The Formula as Used........203 III. The LImitations of the Formula........ 204 1. Through Effects of Irregular Furnace-Work.....204 2. Through Ratio Between Heat-Requirements in Shaft and Hearth. 20.5 IV. The Formula Applied to Actual Furnace-Records,.. 209 1. Description of Furnace-Stock........ 209 2. Furnace Dam..........210 3. Application of Formula..211 4. Average Furnace-Practice..213 V. Sources of Error........... 214 VI. SuggesTions for Practical Methods of Fuel-Economy... 215 VII. Efficiency as a Factor in Furnace-Management.... 219 1. The Efficiency Principle........ 219 2. The Application to the Blast-Furnace..220 I. Introduction. The heat-balance of the blast-furnace has been a favorite subject for discussion for many years. and its study has contributed much to our knowledge. and still possesses a certain academic interest. As a means of accounting for differences in fuel-consumption, however. it has failed utterly. and it is evident that we must look elsewhere for the means of accomplishing this end.

Jan 1, 1912

By Ernest A. Hersam

The small amalgamation-test of the laboratory is not always reliable as a basis for important decisions as to the character and commercial treatment of ores. The conditions of continuous practice on a large scale are not always reproduced in the brief laboratory-test. Sometimes such a reproduction would be very difficult, or impracticable; sometimes it is not even attempted, and the test is performed in a rough way, without regard to the effects of small variations in the methods pursued. The aim of a laboratory amalgamation-test is to learn how much of the gold or silver in an ore can be economically recovered by amalgamation on a commercial scale. The yield can be increased, perhaps, by additional chemical treatment or by extreme comminution of the ore; but this might cost more than the value of such increase. Moreover, in practice, other operations often follow amalgamation; and these operations may remedy a defective extraction by amalgamation, more economically than could be done by directly increasing that extraction. The test should be performed, therefore, upon a uniformly-sized material, and under conditions that are precisely known and capable of being exactly duplicated, or purposely modified. The crucial feature of the test is the effectiveness of the contact made between the gold or silver of the ore and the amal-gamating-surfme. This may depend upon the temperature; the duration of contact; its force, due to gravity or impact; the hardness, plasticity or liquidity of the amalgam; the roughness or other quality of the amalgam-surface; the scouring action of the ore upon the amalgam, or the suspension and

Jan 1, 1905

By R. J. Colony

THE failure, or disintegration, of concrete in structures, even when the cement, sand, and coarse aggregate used have passed satisfactorily all tests and inspections, is not uncommon. Such failures occur even when proper methods of mixing and placing have been used and where, weather conditions were correct. In these cases, the origin of the trouble must be sought in the cement, therefore some additional mode of determining the quality of cement must be employed. The problem is to find a simple, usable; easily applied method that will supplement the standard tests. The solution of this problem in-volves a knowledge of the chemical composition of Portland cements, also of their constitution (or componental composition), as the behavior of a cement, when gaged, is dependent on the physical and chemical characters of the compounds of which it is composed, the proportions existing between them, and the fineness of grinding. It is likewise essential to know the character, behavior, and composition of the hydration, products of Portland cement. The most promising method of attack makes use of chemical, mechanical, and petrographic methods. Chemical, by determining quantitatively not only the usual constituents, but the carbon dioxide and water. Mechanical, by determining the fineness with the air analyzer,1 which separates into fractions of various grain dimensions all of that portion, which in the ordinary sieve test passes the 200-mesh sieve and constitutes at least 75 per cent. of the total cement. These fractions may be further studied chemically and petrographically and micrometric measurements made of the grains. Petrographic, by the method of immersion, and by making thin sections from test pats of both neat cements and standard` mortars.

Jan 1, 1921

By John R. Freeman

This paper relates entirely to the casting of brass under fluid pressure in steel dies. Die castings of metals and alloys of low melting point have been available for many years but the development of brass die castings has been relatively recent, occurring within the past five years. The successful developnlent of brass die castings has resulted from the availability of alloy steels that would give satisfactory life as dies and the development of suitablc die-casting machines. The melting point of copper is 1084" C. (1983" F.) and of a high brass about 900" C. (1652" F.), as compared to 327.5" C. (621.5" F.) for lead, 419.4' C. (786.7" F.) for zinc and 658.7" C. (1217.7" F.) for aluminum, temperatures that are indicative of the casting temperatures required for the various types of alloys, of which the melting points are somewhat lower than those of the pure metals. Type of Die-casting Machine In the well-known plunger and gooseneck types of die-casting machines used for casting the alloys of relatively lower melting point, much of the working mechanism is immersed in the molten alloy. For alloys having the relatively high melting point of brass, this obviously is impossible. Machines with a separate melting chamber are essential. Two rather distinct types are in extensive use at the present time, the Pack and Polak machines, the former designed by Charles Pack and developed at the American Brass Co., the latter developed by Joseph Polak, of Prague, Czeclioslovakia. The principles of operation of these machines have been described in articles by Pack1,2,3 and by Sieg.4

Jan 1, 1935

By Albert Wiggin

THE copper-bearing sulphide ores from the mines in Butte, Mont., which are for the most part concentrated at the Boston & Montana duction Works in Great Falls and at the Washoe Reduction Works in Anaconda, contain the following minerals of economic value: Chalcocite, Cu2S; enargite, Cu3AsS4; cupriferous pyrite; bornite, Cu3FeS3; covellite, CUS; tetrahedrite, 4 CuS2Sb2S3; and tennantite, Cu8AsS7;. All of the ores carry a high percentage of pyrite. Many of the above sulphides are argentiferous and also carry from 10 to 20 cts. per ton in gold. The gangue is quartz and highly altered granite, with sphalerite and galena and more rarely barite and hubnerite as accessory minerals. An average chemical analysis of the second-class ore concentrated at Great Falls and Anaconda would be as follows: Copper 3.2 to 3.4 per cent. Silver 2. 3 to 3.0 oz. per ton. Gold 0.0-1 to 0.15 oz. per ton. Si02.. 55 to 60 per cent. FeO 12 to 15 per cent.. Sulphur 12 to 1.5 per cent. Al2O3, S to 10 per cent. CaO 0.5 to 0.8 percent. As203, 0.5 to 0.6 percent. Lead 0.2 to 0.3 percent. Before describing the Great Falls flow sleet as installed, at Anaconda, a brief history of the Great Falls concentrator will be given, including a description of the various concentrating machines and systems which have been tested in the search for a flow sheet which would give a higher recovery of copper.

Jan 8, 1913

By John R. Freeman

This paper relates entirely to the casting of brass under fluid pressure in steel dies. Die castings of metals and alloys of low melting point have been available for many years but the development of brass die castings has been relatively recent, occurring within the past five years. The successful developnlent of brass die castings has resulted from the availability of alloy steels that would give satisfactory life as dies and the development of suitablc die-casting machines. The melting point of copper is 1084" C. (1983" F.) and of a high brass about 900" C. (1652" F.), as compared to 327.5" C. (621.5" F.) for lead, 419.4' C. (786.7" F.) for zinc and 658.7" C. (1217.7" F.) for aluminum, temperatures that are indicative of the casting temperatures required for the various types of alloys, of which the melting points are somewhat lower than those of the pure metals. Type of Die-casting Machine In the well-known plunger and gooseneck types of die-casting machines used for casting the alloys of relatively lower melting point, much of the working mechanism is immersed in the molten alloy. For alloys having the relatively high melting point of brass, this obviously is impossible. Machines with a separate melting chamber are essential. Two rather distinct types are in extensive use at the present time, the Pack and Polak machines, the former designed by Charles Pack and developed at the American Brass Co., the latter developed by Joseph Polak, of Prague, Czeclioslovakia. The principles of operation of these machines have been described in articles by Pack1,2,3 and by Sieg.4

Jan 1, 1935

By T. A. Rickard

From time immemorial the fissure-vein has been held the simplest type of ore-deposit. The prominence given to it by Cotta and his disciples, from their study of the mines of the Erzgebirge, is impressed upon technical literature; and, in consequence, the ores which carry the valuable metals have been supposed to occur mainly in fissures, cleaving the rocks in diverse directions, and the noblest type of vein has been deemed that which cut across the country independent of its structure, whether evidenced as bedding, foliation or cleavage, and which was identified with rents produced in the rocky crust of the earth. As so conceived, the vein was a fissure filled with ore, extending through the country for a varying distance, and continued downward to a depth more or less proportionate to its longitudinal extent. The vein-material was bounded by an encasement of rock, and those immediate surfaces which limited it on either aide were called " walls." These primary conceptions have become modified by the experience of modern mining in widely separated regions. The study of lode-formations has led to the recognition of notable departures from the supposed normal structure of the veins of Saxony and Cornwall, the two classic homes of early economic geology. Typically the walls of a vein are conceived as parallel rockplanes enclosing the ore; the upper one being called the " hanging-," and the lower the "foot-wall."* Walls are rarely alike. Even where a vein traverses a homogeneons formation, such as a massive crystalline rock, it is usually found that the surface which bounds it underneath

Jan 1, 1897

By Thomas Haight Leggett

I.—The Deep-Level Shafts. The gold-deposits of the Witwatersrand (Anglice, " White Waters' Range ") are, as is well-known, more or less parallel and tilted sedimentary beds of quartz-pebble conglomerate impregnated with gold. These beds, however, are locally called "reefs"—a term equivalent in signification to the American "ledge"—and, like the latter, usually applied to lodes, though covering in practical usage all deposits of tabular form. The first developments of the reefs of the Rand were naturally made along their outcrops. Since the mining law of the Transvaal does not confer upon locators the "extralateral right," the property of each locator upon the outcrop or apex ends with the vertical planes drawn through the boundaries of the claim. Consequently those portions of the reefs which lie "on the dip," beyond these boundaries, are separately acquired by locating new surface-claims, and are usually to be mined only by means of vertical shafts, reaching the reefs at considerable depths. The term "deep-level properties " is given to such claims on the dip, and the " deep-level shafts " are the vertical shafts sunk in the hanging-wall of the Witwatersrand reefs, in contradistinction to the incline-shafts almost universally employed on the outcrop-properties. Number and Distribution.—The accompanying diagram, Plate I., shows the number and depth of these deeplevel shafts, completed or under process of sinking, up to January 1, 1900. A number of shafts already located upon new deep-level properties, but upon which no work has yet been done, are not included in this diagram.* Vertical shafts sunk upon outcrop-

Jan 1, 1901

By V. R. Garfias

Although the work on which this paper is based was carried on by the writer as Special Commissioner of the Petroleum Department of the Mexican Government, the opinions expressed are only his personal views for which the Mexican Government can in no way be held responsible. Notwithstanding that the appointment covers all phases of the so-called petroleum question, as the one question of immediate importance was that relating to taxation, it was decided to devote all the time to this phase of the work. The present report has been divided into two closely related parts, the first dealing with the production and marine transportation of Mcxican petroleum, and the second, with the Mexican taxation on petroleum and its products. The writer wishes to acknowledge the loyal cooperation rendered by Mr. M. C. Ehlen, who had charge of the statistical work, and by Miss S. Stern and Messrs. E. P. Heiles and J. E. Morrissey. The aim throughout the work has been to pave the way for a thorough understanding between the Mexican Government and the oil operators and to present a true and clear statement of facts relating to the questions at issue. Mexican Oil Fields Development The salient features in the development of the Mexican oil fields may be summarized as follows: 1901. First commercially productive well in Ebano field. 1902. Tehuantepee field came in; Diaz Government granted concession to Pearson & Son on practically all Federal lands along the Gulf of Mexico. 1907. First producing well in the Furbero field. 1908. Dos Bocas well caught fire, advertising tremendous productivity of Southern oil fields of Mexico.

Jan 1, 1921

By Frank Rieber

THE discovery that strongly magnetic bodies localized near the surface of the earth could be detected by the distortion which they produced in the resultant magnetic field marked the beginning of magnetic surveying methods. From an original ability to detect bodies of magnetic iron ore and the like when located very close to the, surface, these methods have been extended until today they promise to give much information with regard to the structure of such slightly magnetic material as sedimentary rock containing only a very small proportion of iron.1 The recent extensions have been made possible through the development of more delicate instruments, and of methods for their use. From the original compass and dip needle, the design of apparatus has progressed until equipment Is typified by magnetic balances capable of measuring the components of the earth's field to an extremely high degree of accuracy. It seems unlikely that the limit of such instrumental development has been reached. Just as the change from compass and dip needle has enabled the location of relatively minor changes in magnetic materials, so additional developments in the direction of increased sensitivity, as well as in greater dependability and constancy of operation, should reveal positively many slight changes which either escape notice in the present surveys or are so small that they cannot with certainty be separated from uncontrollable errors due to inconstant operation of the equipment. The ability to read smaller and smaller variations does not mean, of course, that deductions as to the causes of these variations will be made as accurately and definitely as -is possible with the more pronounced anomalies.

Jan 1, 1928

By Frederick Rhines

THE investigations of Wyman1 have demonstrated that copper deoxidized with several of the commonly used agents that confer immunity to ordinary hydrogen em-brittlement can still be embrittled if it is annealed alternately under oxidizing and reducing conditions. During the oxidizing cycle, oxygen diffuses into the copper and frequently deposits a subscale composed of the oxide of the residual deoxidizing agent. Upon subsequent reduction with hot hydro-gen, the copper becomes ruptured along the grain boundaries to a depth sharply limited by the previous penetration of oxy-gen as delineated by the inner boundary of the subscale. Obviously the sensitivity to this kind of hydrogen embrittlement is engendered by the introduction of oxygen during the oxi-dizing anneal, but beyond this the mecha-nism of the process, and hence the controlling factors, remain obscure. There are several possibilities: (I) oxygen dissolved in the copper matrix of the subscale may, upon cooling prior to the hydrogen anneal, precipitate as cuprous oxide which is subse-quently reduced by hydrogen as in the familiar case of hydrogen embrittlement; (2) oxygen in solid solution in copper may itself confer susceptibility to embrittlement by hydrogen; (3) the normally refractory oxides such as those of aluminum, silicon and titanium may themselves he reduced by hydrogen when in contact with copper; or (4) the precipitated oxides of the sub-scale may be complex compounds such, perhaps, as Si02-Cu20, which are partially reduced by hydrogen. These possibilities have been examined, and it has been con-cluded that the first three and possibly the fourth are operative collectively or indi-vidually under more or less predictable conditions.

Jan 1, 1940

G. R. GOHN. l-1n Table I11 of The Sager, Brown, and Mears paper, which was presented on the screen, data were given showing the results of accelerated corrosion tests of certain magnesium alloys. Mention was made that these were carried to a certain time which was used as a measure of failure but no mention was made as to the period of time. I would like enlightenment on that. G. F. SAGER (Author).-In reply to Mr. Gohn's question regarding the times of exposure for the accelerated stress-corrosion tests referred to in Table I11 of our paper, which shows the correlation between accelerated and atmospheric stress-corrosion tests on magnesium alloys, I can say that we usually run the accelerated tests on such alloys for at least 500 hr. We feel that this is long enough to reveal any marked susceptibility to stress-corrosion cracking. In the case of the atmospheric tests on such alloys, we have not yet decided how long we should expose the specimens. Most of them are being exposed for indefinite periods and a good many of our specimens have now been exposed for several years. We may want to continue some of the tests for five or ten years. The period of six months mentioned in connection with the times of exposure for the atmospheric specimens was a rather arbitrarily selected minimum time for which specimens had to be exposed before we counted them with those that had not failed. A fairly large number of magnesium- alloy specimens have been exposed in the atmospheric stress-corrosion tests at var-

Jan 1, 1945

The meeting of the Institute at St. Louis brought together many members of the Women's Auxiliary, and Mrs. Philip N. Moore, who was nominated as the Director for the St. Louis Section, took the occasion formally to inaugurate the organization in that district. A meeting was held at the Planters Hotel, anti after discussion as to, the aims and objects of the. Auxiliary, officers were nominated for the' Section; the meeting then adjourned for two days, to he resumed in Joplin.. Here a very successful meeting was held, at which the Vice-Chairman, Secretary, and Treasurer were elected. A great deal of interest was arouse under the able directorship of Mrs. Moore the St. Louis Section is likely to become a large and active organization. The president of the Women's Auxiliary, in opening the meetings, told the ladies present of the inauguration of-the-Society in February, 1917, and of the work which had been accomplished up to date. She told how the Society devotes itself to patriotic and humanitarian work along lines acceptable and interesting to the Mining Engineer, standing always alongside and behind the men of the profession. The Central Welfare Committee of the organization has three Sub-Committees: Foreign Relief, Emergency, and Americanization, and under one or other of those heads most of the work of the' Society has been done. Mr. Hoover was responsible for the inception of the Foreign Relief Committee, as its first work was the collection of funds for the supplementary meals for the Belgian Children. Under the energetic administration of Mrs. H. Knox, this sub-committee raised $12,100 in the period between the February meeting and the Declaration of war by the United States, when our government took over the entire duty of feeding starving Belgium. The organization of the Belgian Relief Committee, as it was styled, still remains, but the members are now asked to take up the question of relief in France. The President, Mrs. S. J. Jennings suggested at the St. Louis meetings that one way of working for the foreign relief alight be that all the members of the Auxiliary should, during the period of the war, forego all giving' and receiving of Christmas presents, except those they have been accustomed to give to the poor or in charity, and those they would give to the men in the services of the United States; that the money usually spent on the Christmas gifts should be put into a fund to be sent abroad for the fatherless children of France, as a gift from the families of the Institute. A good deal of discussion followed this proposal, as some of the ladies felt that children should have their Christmas gifts as usual. The Director of the Section emphasized the truth that the Christmas spirit was the .spirit of giving and sacrifice, and that no sacri-

Jan 1, 1918

By S. J. Hruska

Rate expressions for the formation of two-and three-dimensional nuclei on foreign substrates are developed, taking into account previously neglected contributions to the standard Gibbs free energy of formation of critical nuclei. The temperature dependence of critical super saturation data predicted using these expressions is in accord with data for cadmium on copper and sodium on CsCl. EXPERIMENTAL data on the heterogeneous nuclea-tion of metal crystals from the vapor phase1&apos;2 exhibit the temperature dependence predicted by a nucleation rate equation derived by Pound et al.3 In their treatment, the critical nuclei are visualized according to the Volmer4 model as cap-shaped (three-dimensional). Accordingly, it seems desirable to compare these data with a nucleation rate equation which is derived on the assumption of disk-shaped (two dimensional) nuclei. Further, Lothe and Pound5 have recently shown that the standard Gibbs free energy of formation of these critical nuclei contains a contribution which has heretofore been neglected. Thus it is necessary to re-examine these nucleation data using a rate equation which contains this contribution. The van&apos;t Hoff isotherm relates n(i), the concentration of nuclei of critical size i (i = number of atoms), to nil), the concentration of adsorbed single atoms: where standard Gibbs free energy of formation of critical nuclei given by is temperature insensitive and is the bulk free energy change/volume of transformed material], T = substrate temperature and k = Boltzmann&apos;s constant. Previously,3 was determined by considering only the contributions of bulk and surface free energies in transforming i atoms from the population nil) to a cluster of i atoms. It has been shown5 that this procedure does not take into account the free energy contribution arising from the multiplicity of sites, q, where the clusters can be situated. If this contribution, -kT In q/n(l),is added to iG3 [Note that this increases n(i) by a factor q/n(l).] Since the above does not affect the remaining terms in the rate expression of Pound et al., the details are referred to their paper. The resulting nucleation rate is If the experimental AGV and T values at some common value of are employed, a plot of vs T(ln C3/l + In p&apos;) should yield a straight line of slope k/B<p and intercept . The corresponding plots for / = 1 nucleus per sq cm sec and C3 = 1018 are shown in Figs. 1 and 2 for cadmium on copper1 and sodium on CsCl2 and the values of obtained therefrom are entered in Table I. It is apparent that the data yield reasonable straight lines with about the same scatter as found using the equation of Pound et al. When the configuration of minimum free energy for a nucleus is a circular monatomic layer, the standard free energy of formation is

Jan 1, 1963

By J. M. Bugbee

The engineer and the conservationist agree that effective water drive is the desirable reservoir production mechanism. Water drive may result either from the expansion of edge water, the reservoir water bordering an oil pool, or from the artesian flow of edge water from the outcrop. Thus, the extent of the reservoir has an important bearing upon both the rate and the ultimate quantity of water influx to an oil pool. Lens-type reservoirs are generally recognizable, but the complete structure of the more important domal types, having possible limitations from crestal and synclinal faulting, is not well understood. The delineation from cores, electrical logs and exploitation phenomena of the crestal portions of reservoirs is increasingly exact. This paper suggests that inference from these factual pictures, combined with the scattered well and geophysical data of the synclines and with consideration of the dynamics of structural formation, may be applied to solving the complete geologic structure. Since faulting on the domes and in the synclines may effectively seal and thus limit the size of a reservoir and bar additional water influx, consideration of geologic structure and its possible effects is essential to complete analysis and prediction of reservoir performance. Introduction Implicit in reservoir studies is the fact that the oil must be displaced from the reservoir rock by some other fluid, either gas or water, and this understanding yields the terms descriptive of the major reservoir production mechanisms, gas expansion and water drive&apos; Three recent papers1-2-3 make clear the economic and conservation preeminence of Water drive as a production mechanism; in fact, the title of the latest of these is " Production under Effective Water Drive as a Standard for Conservation Practice." There appears to be an assumption at times among analysts that the effectiveness of a water drive is solely dependent on the rate of oil production; that is, if water drive appears to be insufficient or lacking, a lower oil-recovery rate would increase or reveal it. This assumption might result from the fact that the analysis has been wholly developed during the period of production curtailment; that is, since 1929. The writer takes it that the recurrent phrase in De Golyer&apos;s paper,3 "some degree of water drive," is related to this assumption. In California, an extraordinary phrase, "inactive water drive," is rather common and the connotation of uncertainty regarding our knowledge of reservoir performance is evident. Wyckoff2 speaks of the type of reservoir and performance as follows: "In general, reservoirs may be any one or a combination of domal, faulted, lenticular, or stratigraphic traps. Insofar as the dynamic performance of such reservoirs is concerned, the particular type merely determines whether regional flow is symmetrical as in a uniformly developed domal or lenticular type, or one-sided as in many stratigraphic or faulted traps." But whether the flow is

Jan 1, 1943

By H. T. Bowman

FOR more than 80 years the Bessemer process has depended upon the ability, skill, and judgment of the blower, although as early as the 1860&apos;s it was recognized that the process would benefit by some type of instrumental control.1 However, instruments with sufficient recording speeds did not exist, so the end-point determination was always dependent upon the blower&apos;s eye. This placed an obstacle in the way of precise experimental work, because of the absence of the necessary records and reference points as reported by Work.2 The use of the photocell provided the instantaneous record of the blow that made this experimental work possible and provided more scientific control for the process as discussed by Graham3&apos; A brief description of the progress of the blow will illustrate the recording function of the instrument. The silicon in the iron is being oxidized during the first minutes of the blow, as pointed out by Henning4 in a table showing the order of metalloid elimination. The product of this oxidation is a solid that remains in the converter, so there is virtually no flame during this part of the blow. This low flame luminosity is illustrated by the flame recording shown in Fig. I, where the silicon blow is plainly marked. The dull flame of the silicon blow gradually gives way to the brilliant carbon flame as the increasing quantities of carbon monoxide formed inside the converter burn to dioxide upon contact with the atmosphere above the vessel. When the carbon reaches some low value under 0.20 per cent, there is insufficient monoxide formed to maintain the dioxide flame, so its intensity drops. Throughout the flame drop carbon continues to burn, until at some value around 0.05 per cent an arrest occurs in the recorded drop. This point has been designated as the end point. The period of time from this end point until the vessel is turned upon its side and blowing has stopped has been called the afterblow. This afterblow is used as a measure of the degree of metal oxidation, and uniformity demands that it be controlled within narrow limits. Iron and blowing conditions are likely to change several times during a turn, necessitating corresponding changes in end-point control. It is the purpose of this paper to discuss these changes, the factors that make them necessary, and their bearing upon the quality of steel. CARBON-FEO RELATIONSHIP In the Bessemer process oxidation relationships are precise. Fig. 2 shows a graph of the carbon-FeO relationship. The familiar "bomb-test" method, described by McCutcheon and Rautio,5 was used for obtaining these and all other dissolved FeO values herein reported, all tests being taken from the converter before deoxidation unless otherwise noted. All tests of 0.10 per cent carbon and above were obtained from metal blown for duplexing. McGinley and Woodworth6 reported iron oxide values for blown metal, but their tests were obtained by a different method than were those

Jan 1, 1942

By J. M. Bugbee

The engineer and the conservationist agree that effective water drive is the desirable reservoir production mechanism. Water drive may result either from the expansion of edge water, the reservoir water bordering an oil pool, or from the artesian flow of edge water from the outcrop. Thus, the extent of the reservoir has an important bearing upon both the rate and the ultimate quantity of water influx to an oil pool. Lens-type reservoirs are generally recognizable, but the complete structure of the more important domal types, having possible limitations from crestal and synclinal faulting, is not well understood. The delineation from cores, electrical logs and exploitation phenomena of the crestal portions of reservoirs is increasingly exact. This paper suggests that inference from these factual pictures, combined with the scattered well and geophysical data of the synclines and with consideration of the dynamics of structural formation, may be applied to solving the complete geologic structure. Since faulting on the domes and in the synclines may effectively seal and thus limit the size of a reservoir and bar additional water influx, consideration of geologic structure and its possible effects is essential to complete analysis and prediction of reservoir performance. Introduction Implicit in reservoir studies is the fact that the oil must be displaced from the reservoir rock by some other fluid, either gas or water, and this understanding yields the terms descriptive of the major reservoir production mechanisms, gas expansion and water drive&apos; Three recent papers1-2-3 make clear the economic and conservation preeminence of Water drive as a production mechanism; in fact, the title of the latest of these is " Production under Effective Water Drive as a Standard for Conservation Practice." There appears to be an assumption at times among analysts that the effectiveness of a water drive is solely dependent on the rate of oil production; that is, if water drive appears to be insufficient or lacking, a lower oil-recovery rate would increase or reveal it. This assumption might result from the fact that the analysis has been wholly developed during the period of production curtailment; that is, since 1929. The writer takes it that the recurrent phrase in De Golyer&apos;s paper,3 "some degree of water drive," is related to this assumption. In California, an extraordinary phrase, "inactive water drive," is rather common and the connotation of uncertainty regarding our knowledge of reservoir performance is evident. Wyckoff2 speaks of the type of reservoir and performance as follows: "In general, reservoirs may be any one or a combination of domal, faulted, lenticular, or stratigraphic traps. Insofar as the dynamic performance of such reservoirs is concerned, the particular type merely determines whether regional flow is symmetrical as in a uniformly developed domal or lenticular type, or one-sided as in many stratigraphic or faulted traps." But whether the flow is

Jan 1, 1943

By G. C. McCartney, S. J. Kidder

The Helen Mine, of the Algoma Steel Corporation, in the Michipicoten district, Ontario, Canada, has produced more than 6,240,290 tons of iron ore. Prior to and during World War I, 2,823,369 gross tons of brown ore were shipped, and from 1939 to the end of the 1944 season, 3,416,921 gross tons of siderite ore were produced from open-pit operations. Brief descriptions are given of the nature of the ore, the mining methods employed and the manner of treatment of the ore. Shipment of the finished product, known as Algoma sinter, is made to blast furnaces in both Canada and the United States. The iron-ore bodies—i.e., the oxide ores of the Old Helen and the siderite of the New Helen—are a part of a tabular shaped area of iron formation that extends over a length of more than 100,000 ft. and has a maximum width of 1000 ft. The ores are considered to be a product of introduction of iron-bearing material accompanied by replacement of the rocks already present. It is shown that introduction took place subsequent to the development of the major folded structures. It is believed the iron-bearing material emanated from an igneous source. Introduction The Michipicoten mining district derives its name from the Indian word1 meaning "place of bold promontories" or "region of big places," and anyone who has visited this part of Canada will agree that the district is well named. In 1897, there was active prospecting for gold in the district and the Ontario Bureau of Mines2 opened a recording office at the Hudson&apos;s Bay post at Michipicoten River. In the summer of 1897, Ben Boyer, probably searching for gold, discovered an outcrop of brown iron ore at the east end of a small lake, less than 8 miles, in an air line, northeast of the nearest point on Michipicoten Harbour. In the following year, extensive surface exploration and diamond drilling disclosed a commercial body of nonbessemer brown ore, possibly 700 ft. long and 200 ft. wide, of about the following analysis:3 Fe (natural), 57.15 per cent; S, dried at 212°F.. 0.113; SiO2, dried at 212°F., 4.00; P, dried at 212°F., 0.125. The property (Figs. 1-3) was taken over by E. V. Clergue and ultimately was transferred to the Algoma Steel Corporation. The Algoma Central Railway shortly afterward built its line from Michipicoten Harbour to the mine, together with an ore dock at the Harbour. Thus, within three years of its discovery, the mine had adequate shipping facilities and a market for its ore. Production of Brown Ore and Pyrite The first shipment of brown ore was made in July 1930. By 1939, the mine was shipping at the rate of 170,000 long tons

Jan 1, 1949

By S. J. Kidder, G. C. McCartney

The Helen Mine, of the Algoma Steel Corporation, in the Michipicoten district, Ontario, Canada, has produced more than 6,240,290 tons of iron ore. Prior to and during World War I, 2,823,369 gross tons of brown ore were shipped, and from 1939 to the end of the 1944 season, 3,416,921 gross tons of siderite ore were produced from open-pit operations. Brief descriptions are given of the nature of the ore, the mining methods employed and the manner of treatment of the ore. Shipment of the finished product, known as Algoma sinter, is made to blast furnaces in both Canada and the United States. The iron-ore bodies—i.e., the oxide ores of the Old Helen and the siderite of the New Helen—are a part of a tabular shaped area of iron formation that extends over a length of more than 100,000 ft. and has a maximum width of 1000 ft. The ores are considered to be a product of introduction of iron-bearing material accompanied by replacement of the rocks already present. It is shown that introduction took place subsequent to the development of the major folded structures. It is believed the iron-bearing material emanated from an igneous source. Introduction The Michipicoten mining district derives its name from the Indian word1 meaning "place of bold promontories" or "region of big places," and anyone who has visited this part of Canada will agree that the district is well named. In 1897, there was active prospecting for gold in the district and the Ontario Bureau of Mines2 opened a recording office at the Hudson&apos;s Bay post at Michipicoten River. In the summer of 1897, Ben Boyer, probably searching for gold, discovered an outcrop of brown iron ore at the east end of a small lake, less than 8 miles, in an air line, northeast of the nearest point on Michipicoten Harbour. In the following year, extensive surface exploration and diamond drilling disclosed a commercial body of nonbessemer brown ore, possibly 700 ft. long and 200 ft. wide, of about the following analysis:3 Fe (natural), 57.15 per cent; S, dried at 212°F.. 0.113; SiO2, dried at 212°F., 4.00; P, dried at 212°F., 0.125. The property (Figs. 1-3) was taken over by E. V. Clergue and ultimately was transferred to the Algoma Steel Corporation. The Algoma Central Railway shortly afterward built its line from Michipicoten Harbour to the mine, together with an ore dock at the Harbour. Thus, within three years of its discovery, the mine had adequate shipping facilities and a market for its ore. Production of Brown Ore and Pyrite The first shipment of brown ore was made in July 1930. By 1939, the mine was shipping at the rate of 170,000 long tons

Jan 1, 1949

By S. F. Ravitz

IN his excellent book on the Principles of Flotation, Wark&apos; makes the following significant statement concerning the theory of flotation: Two questions of first-rate importance must be considered . . . First, it must be decided whether the sulfide minerals require a collector in order that they may float, or whether as has been claimed, they possess an inherent floatability and need no collector. Second, it must be decided whether the xanthate type of collector can react with or be adsorbed by the unchanged sulfide minerals themselves, or whether, as many claim, reaction with the collector is dependent upon initial oxidation of the mineral surface. In the theory of flotation there are no two questions of greater importance than these. Ravitz and Porter&apos; presented evidence that galena can be floated without a collector, and even without any reagent, provided oxidation products are thoroughly removed from its surface. They found also that thoroughly cleaned galena floated faster when xanthate was used than when a frother alone or no reagent was used, and that, without a collector, the recovery decreased gradually upon exposure of the mineral to air. Their work, however, has met with considerable criticism. I(127).3-6 This paper is presented to answer the objections that have been raised, and to present additional data that confirm their results. EXPERIMENTAL PROCEDURE The apparatus used to provide oxygen-free conditions for flotation has been described in detail by Ravitz and Porter. An atmosphere of purified nitrogen was maintained within the apparatus; all water and solutions used were freed of dissolved air, and could be transferred where desired by the use of nitrogen pressure; nitrogen was used as the gaseous medium for flotation. The flotation cell was essentially a glass cylinder 15 cm. long and 4.6 cm. in diameter. Near the bottom was sealed a fritted glass filter, which broke up the gas into small bubbles, and 6 cm. above this filter was a side arm through which the froth overflowed. The pulp was agitated by a glass impeller, which entered the cell through a mercury seal. For each test 17 grams of galena and 75 ml. of water were placed in the cell, after which the speed of the impeller and the rate of gas flow were adjusted. Water was added gradually during the test to keep the froth level at the proper height. The mineral was prepared and cleaned in the following manner. Exceptionally pure galena was crushed by hand on a clean bucking board, screened to - 150+ 200 mesh, and deslimed on a zoo-mesh sieve with a fine spray of water. It was then boiled on a hot plate for a number of hours with several changes of the desired cleaning solution, after which both the solution and the mineral were placed in the "mineral flask" of the apparatus. The cleaning solution was drained off, and the mineral was boiled with oxygen-free water

Jan 1, 1940