Search Documents

By Richard P. Rothwell

THE communication which I have to lay before my fellow-members of the Institute, is no elaborate paper, nor the statement of any great discovery ; it is simply the record of convenient methods of conducting topographical surveys, and of keeping the notes of the same; methods that have grown out of practical experience, and have saved me many a day's labor by facilitating office and field work, and at the same time secured a greater degree of accuracy than is obtained by the methods now in general use. I assume it as granted that no topographical map is worthy of the name, except it represent the elevations and depressions of the surface by means of horizontal or contour lines. In the Ordnance Survey of Great Britain, the contour lines are traced for every fifty feet vertical height, I believe, by running out the line with level and compass through all its meanderings on the surface ; this, of course, is a very tedious, though accurate process, but "in the woods," where many of our surveys have to be made, it would be practically impossible. Some time ago, I made an extensive and quite elaborate topographical survey and contour map of the southern portion of the Cahaba coal-field, in Alabama, the object of the survey being to

Jan 1, 1875

By E. R. Funk, H. Udin, J. Wulff

The surface tension of solid silver is measured by a refinement of the Udin, Shaler, and Wulff technique. The tests were made in a purified helium atmosphere at four different temperatures and various times. The average of the results is y = 1140 + 90 dynes per cm for the range 875° to 932°C. A SUCCESSFUL measurement of the surface tension of solid copper was reported by Udin, Shaler, and Wulff.' They performed experiments on copper held in vacuum within 100°C of the melting point. At these temperatures, the creep rate in 5 and 3 mil copper wires was sufficient to permit determination of a balance between the contractile force of surface tension and the extending force of small copper weights joined to the end of the wire specimens. By suspending a series of variously weighted specimens and measuring the change in a gage length during the test, the balancing applied load could be found. This point of zero strain is a measure of the surface tension. The mathematical formulation of this gives: w = r y [1] where w is the weight for zero strain; r, the radius of the wire; and y, the surface tension. A subsequent note by Udin pointed out that eq 1 applies only to single-crystal specimens. Since the specimens used revealed a "bamboo" structure upon

Jan 1, 1952

By D. L. Luffel

This paper presents two main developments: (1) a short, constantly accelerated centrifuge method of measuring drainage capillary pressure properties of cores, and (2) a new analytic method of treatment of centrifuge measurements to obtain saturation-capillary pressure relations. Toward the first objective, a clever experimental method is presented which is certainly more rapid than previous centrifuge methods. Toward the second objective, a new analytic method is derived to eliminate the approximate method of Hassler and runner. The derivation of this new analytic method, however, appears to be in error. The new analytic solution is developed as Eq. 5 in Appendix A. At the beginning of this derivation, the average wetting phase saturation of a core is expressed as, where is the centrifuge angular velocity. Eq. D1.2 makes explicit the dependence of S and S upon The second equation shown in Appendix A expresses the relation between the three variables Since for a given porous medium the saturation is uniquely related to capillary pressure, the functional dependence of S upon P is trivial, i.e., Pc.ri does not actually appear. Thus, the function 5 (r, ) may be expressed as a new function, S*, of PC, , alone The author transforms the variable of integration in Eq. Dl through use of Eq. D2 and writes

Jan 1, 1965

By L. W. Eastwood

THE structure of eutectics has been studied by a number of investi-gators, and the complexity of the structural relationship of the compo-nents has been agreed upon, especially that of the "eutectic colony," type III of Portevin's1 classification. This paper does not attempt to alter the present classifications of eutectics; rather, it discusses the relationship between the macrostructure and the microstructure of the copper-cuprous oxide eutectic, and describes in detail the mechanism of the formation and the structure of the eutectic. Further, throughout the entire discussion it attempts to point out certain misconceptions in regard to the interpretation of the observed structure of the copper-cuprous oxide eutectic, one of the so-called "eutectic colony" types, and to correlate as much as possible the work done by the writer with that done by other investigators. Of the three types of eutectics listed by Portevin,2 the eutectic colony type has presented the greatest difficulty in interpretation. Although the copper-cuprous oxide eutectic is typical of the eutectic colony type in appearance, it may not be truly representative because the copper forms about 96 percent of the eutectic and the cuprous oxide about 4 per cent. The interpretation of the origin and structure of the "eutectic colony" given here is strictly limited, therefore, to the copper-cuprous oxide eutectic.

Jan 1, 1933

By Samuel M. Brock

Problems related to strip and auger coal mining have grown with the development of the industry and the economy. New technology has produced equipment that has made mining by surface methods not only highly productive, but potentially highly destructive of water resources and natural environments. On the other hand, growth of the economy has produced an increased demand for clean water and created new demands for amenity values that natural environments provide. Thus, opposing forces have created conflicts in resource use. And these conflicts have made surface mining highly controversial. Resolving the controversy will require the solving of complex economic and social problems. The essence of the economic problem created by surface mining is that, in the absence of proper regulation, substantial costs resulting from the process are borne by the public rather than the mine operator. The major goal for the regulation of the surface mining industry is to provide controls which will promote the attainment of maximum social welfare. Deciding upon the type of controls required, and how to apply them to attain a social optimum, however, poses some very difficult problems. In a comprehensive article on this subject, David B. Brooks defined the problem and suggested that benefit- cost analysis might be helpful in providing guidelines for making decisions about surface mining regulations.1

Jan 5, 1969

By Edgar S. Burkhardt

In mining, the process of comminution starts at the pit and ends at the classifiers. The first machine that breaks or comminutes ore is the primary crusher. There are many types of crushers, but the one most commonly used in large tonnage plants is the gyratory so discussion is restricted to this type of machine. See Figure 1. The primary crusher is the most important piece of comminution machinery in the plant because every ton of ore processed by the concentrator must pass through it, as shown in Figure 2. Most plants can operate if a secondary crusher or a mill is shut down, but if the primary crusher stops, the whole concentrator goes down. It is, therefore, important that the machine be able to produce sufficient ore to keep the concentrator running without hesitation. The plant designer first considers the required daily capacity and an estimate of the size of the ore from the pit. To this he adds an availability factor to compensate for delays due to shovels, trucks and rou- [ ] tine maintenance at the crushing station. This factor is based on experience and can be on the order of 75% (1). With these figures, he determines the hourly capacity required of the primary crushing station to keep the concentrator supplied. See Table I.

Jan 1, 1982

By A. L. Holley

The three principal mines from which the celebrated Salisbury iron ores are obtained are called respectively the "Old Hill," "Davis," and "Chatfield" ore beds, and are situated in the town of Salisbury, Litchfield County, Conn., on the eastern slope of the Tocconuc range of hills.* The Old Hill Ore Bed is a tract of land of 100 acres, originally granted by the General Court in October, 1731, to be laid out by Daniel Bissell of Windsor. It mas Boon after surveyed and located by Ezekiel Ashley and John Pell. The descendants of Ashley are still proprietors in the mine. The supply of ore has been very abundant, and for many years was easily obtained, but latterly the cost of raising has been greatly increased. Up to about 1840 the average yield was estimated to be about 4500 tons per annum. The production has gradually increased until the average yield at present is estimated at 15,000 tons annually. The largest production in any one ymr was about 20,000 tons. The proprietors of this mine were incorporated many years ago under the style of " The Salisbury Ore Bed Proprietors." The Davis Ore Bed, named after an early owner, was originally called Hendricks Ore Bed, and was owned before the organization of the town of Salisbury by Thomas Lamb, one of the first settlers

Jan 1, 1879

By Robert Hunt

(New York Meeting, February, 1913.) I HAVE frequently stated that while the chemical composition of steel is important, yet even greater importance is connected with the mechanical and heat treatment of the metal. During the past year I encountered such a positive example of that fact that I deem it worth putting upon record. A prominent railway system divided an order for open-hearth steel rails between two steel works, both of which are under the control of the one corporation; giving to one about 18,000 tons, and to the other 7,500 tons of the same section and to be made under the same specifications. The rolling results obtained in the two mills varied so widely that a study of the figures is intensely interesting and serves to illustrate the advantages obtained by careful ingot casting, and, quite as pertinently, the possible benefits of careful subsequent heating and rolling with moderate reductions in the rolling process. The smaller order was rolled complete in four installments during the same months that the larger order was being made in six separate installments; but, to permit of exact comparisons, the totals of the four installments (completing the order with the mill which I will call A) are given with the totals of the first four installments of the larger order, made by the mill designated as B. These rolling results are:

Jan 5, 1913

By Clamer, G. H.

G. H. CLAMER, * PHILADELPHIA, PA.-Unfortunately, prior to the war no serious attention was given to the conservation of tin, notwithstanding that this country is practically dependent upon outside sources for its entire tin supply. Tin is of vital importance in many industries, but it is surprising how many and how excellent are its substitutes when we become acquainted with them. Tin has always been a relatively high-priced metal, and it is part of the human attitude to associate high prices with high standards; it is not until the price of a commodity becomes well-nigh prohibitive that we hunt for substitutes, because the idea of substitution seems always to involve an assumption that the substitute must necessarily be inferior. The history of the development of bearing bronzes is a striking example of this policy. In the early clays, copper-tin alloys were almost universally used, the idea then being prevalent, which is still held by many, that a bearing to resist wear must be hard, and the harder the better. The favorite bronze bearing contained 90 per cent. copper and 10 per cent. tin; frequently, in service which was considered severe, even higher proportions of tin were used.. Such hard alloys have great resistance to compression, but as a rule they had a very wide factor of safety in this

Jan 12, 1918

By P. Nelson, K. L. Gunsallus, A. R. Ingraffea, J. F. Beech

INTRODUCTION Fracture toughness, KIC, is an intrinsic material property and is a measure of the energy required to create new surface area in a material. Fracture toughness measurements can be made for a wide range of rock types (Ouchterlony, 1980). As a measure of energy of comminution, fracture toughness might be used for more sensitive predictions of Tunnel Boring Machine (TRM) performance than are possible with other index measures in current use. This paper describes part of an ongoing, comprehensive, analytical/experimental program aimed at evaluation of KIC in such a role. The program includes efforts to: 1. Provide a firm analytical basis for a test specimen geometry: the core-derived short-rod. 2. Develop simple, inexpensive testing equipment and techniques. 3. Evaluate the accuracy of the above by testing rock and other materials and comparing the measured fracture toughness with those obtained by other methods. 4. Measure fracture toughness of a substantial number of different rocks from three ongoing TBM projects. 5. Compare fracture toughness results with other strength measures. 6. Compare all test results with observed TBM performance in the three projects. Presented here are summaries of all but the last of these efforts. Comparative evaluation of KIC as a more senstive rock property for TBM performance prediction will be the subject of the oral presentation and a subsequent paper.

Jan 1, 1982

By H. A. Schwartz, A. F. Gorton, H. R. Payne

In a previous paper1 we published what we believed to be a correct stable equilibrium diagram for an iron-carbon alloy containing + 1.20 per cent. silicon. The purpose of the present paper is to record the results of studies concerning the effect of silicon on the location of the eutectoid points of both systems, including also certain incidental observations of general interest. We prepared white cast irons containing roughly 21/2 per cent. carbon, 0.05 per cent. manganese, and 0.03 per cent. each of phosphorus and sulfur, but of accurately known silicon contents which varied from 0.40 to 3.32 per cent. These were completely graphitized, and both A1 points determined, as in our previous work, the specimens being converted from the stable to the metastable condition and vice versa by appropriate heat treatments. Each stable alloy was heated to a few degrees above Arl for 3 to 7 hr., quenched and analyzed for total and graphitic carbon, the difference being the "combined" or, better, agraphitic2 carbon content of the saturated solid solution just above the eutectoid transformation. One specimen was lost through accident, and the 0.40-per cent. silicon material gave an anomalous result ascribed to difficulty in maintaining the stable system in the presence of but little silicon.

Jan 1, 1923

By R. Sprycha, J. Szczypa, W. Janusz, J. Neczaj-Hruzewicz

INTRODUCTION Because large aqueous suspensions of various fine solids originate during the beneficiation of ores, the Mining Industry constantly requires efficient and feasible dewatering methods. Among the techniques currently in use (1,2), filtration (vacuum, press) and centrifugation are fairly expensive and thus are limited to use with more valuable materials. Furthermore, installations of reasonable size produce only moderate outputs. Therefore, tailings from ore dressing plants are usually treated by sedimentation or settling techniques with a tailings dam as the ultimate sedimentation basin (3). Apart from growing environmental and economic questions, the solid product obtained from the tailings dam basin has in most cases, a rather high moisture content and a persistent semi-fluid consistency. Thus, it is difficult to transport and use further. On the other hand, the solids may be utilized as a filling material, fertilizer, etc. providing they are dry enough and properly granulated. Demands for an improved technique are met to a great extent, by the technique presented in this paper. AGGLOMERATION OF FLOCCIJLATED SLIMES Origin and Qualitative Description of the Process Phenomena of consolidation and pellet formation in flocculated fines were first observed by Yusa and Gaudin (4) while studying rheological properties of flocculated kaolinite. On this basis, methods of separating liquid from solids have been worked out (5-7) and many possibilities for application have been suggested (5,6). Yusa termed the technique "wet pelletization''.

Jan 1, 1980

By H. R. Payne, A. F. Gorton, H. A. Schwartz

In a previous paper1 we published what we believed to be a correct stable equilibrium diagram for an iron-carbon alloy containing + 1.20 per cent. silicon. The purpose of the present paper is to record the results of studies concerning the effect of silicon on the location of the eutectoid points of both systems, including also certain incidental observations of general interest. We prepared white cast irons containing roughly 21/2 per cent. carbon, 0.05 per cent. manganese, and 0.03 per cent. each of phosphorus and sulfur, but of accurately known silicon contents which varied from 0.40 to 3.32 per cent. These were completely graphitized, and both A1 points determined, as in our previous work, the specimens being converted from the stable to the metastable condition and vice versa by appropriate heat treatments. Each stable alloy was heated to a few degrees above Arl for 3 to 7 hr., quenched and analyzed for total and graphitic carbon, the difference being the "combined" or, better, agraphitic2 carbon content of the saturated solid solution just above the eutectoid transformation. One specimen was lost through accident, and the 0.40-per cent. silicon material gave an anomalous result ascribed to difficulty in maintaining the stable system in the presence of but little silicon.

Jan 1, 1923

By E. Alan Haley

Accurate and economic control of line and grade on long tunnels, large structures, excavations and waterways has been a problem to surveyors and engineers for decades. The conventional method of surveying, incorporating a level, transit and a number of surveying technicians, has proven to be a very expensive and time-consuming operation. Now, however, engineers have adapted the laser to help ease the problems of surveying, at the same time increasing the efficiency of such operations. The laser, which projects a continuous, narrow red beam of brilliant light, provides a constant alignment reference that does not interfere with personnel or equipment. A complete laser alignment system, specifically designed for and suited to a variety of mining and tunneling operations, has been developed by the Perkin-Elmer Corp. The engineering significance of this development can be fully realized when it is noted that, aside from potentially tremendous economic advantages in terms of labor savings, the laser beam provides a system of alignment that is at least ten times more accurate than presently used optical systems. The new laser system provides accuracies within 10 microinches per foot (1 x 10-5in.) when used with an accessory centering detector. In one of its first field trials, the laser was used for alignment of a two-mile tunnel which showed a total deviation of less than 5/8 in.

Jan 4, 1968

By H. T. Byck

THE plastering properties of six representative California drilling muds were studied over a temperature range of 70° to 175° F. at several mud weights, using a high-pressure circulating filter press with full size consolidated cores. In all tests, with untreated as well as with chemically treated muds, the filtration rates at elevated temperature were higher than at low temperatures and in nearly every case this increased filtration rate was notably larger than could be attributed alone to the decreased viscosity of water-the flowing medium-at elevated temperatures. It is concluded that no existing method will permit even an approxi-mate determination of the filtration rate at high temperature from data at room temperature. It is necessary to measure filtration at the tem-perature actually anticipated in the well, or to make a sufficient number of tests at various lower temperatures so that a small extrapolation of these data to the anticipated well temperature may be applied. Such tests should be carried out on the mud as actually used in the well. The viscosity of each of the muds was determined over the same temperature range. While no relationship was observed between mud viscosity and plastering properties, it was found that chemical treatment of the muds for viscosity reduction shifted the temperature of minimum viscosity to appreciably higher values than for untreated muds.

Jan 1, 1939

By Henry S. Poole

This field is geologically of much interest. It is small, hut with some seams of unusual thickness, the main one being as much as thirty-eight feet thick. The quality of the seams, as also of the associated beds of shale and sandstone, in several instances changes to a remarkable degree within short, distances. The strata dip at inclinations that carry the coal to depths of 3000 feet or more; heavy faults cut up the district, and the New Glasgow conglomerate, of disputed age, separates it from the Upper Carboniferous measures, in which no seams of workable thickness are known. This coal-field offers to the geologist much ground for study and peculation. The commercial value of the field is affected by its restricted area, the varied quality of its coal, and its advantageous position in the mainland, with railway connection and home markets, offset by the physical difficulties which make the cost of production high. It has been so long a habit with us to speak of our resources of coal as boundless, that any adverse comments, or insinuations that avoidable loss in working is a national loss, hare hitherto fallen on idle ears. While it is not my purpose to underrate the riches we do possess, yet I deem that no good end is served by echoing exaggerated estimates which encourage a national indifference to wasteful

Jan 1, 1886

By T. M. Berry

In the past few years changes have taken place in shaft sinking. Progress has been made with types of machinery designed, developed, and made available to shaft sinking contractors. This is particularly true of drilling and mucking equipment. Compared with conventional clamshell loading, mucking or loading with a crawler-mounted overshot loader is a new technique for shaft work. There are several methods of clamshell loading. Dravo Construction Co. mounts an air tugger on the clamshell to operate the closing line. The load, or holding line, is attached to the hoist of a crane or whirler at the shaft collar. The clamshell is raised or lowered by the hoist when a signal is given by a bell or light system operated by men at the bottom of the shaft. Two men control the drift of the clamshell with tag lines, pulling it to any position in the shaft for loading, or over the shaft muck bucket for emptying. One man operates the air tugger to open and close the clamshell by means of two lines attached to the operating air valve, just as reins are used to drive a horse. One man operates the signal telling the hoist operator when to raise or lower the clamshell. This method requires two hoisting lines in the shaft-the line from the mine hoist that lifts

Dec 1, 1956

By Nathaniel Herz

IN the operation of any ore processing plant, no matter what beneficiation process or combination of processes may be used, certain fundamental figures are regularly needed for essential records and accounting. These include amounts of ore treated and products made, with their assays, as well as quantities of labor and supplies used, with their cost. Usually labor and supplies are broken down and allocated to certain operations by the accounting department, and resulting tabulations are available for study by the milling plant management. However, to avoid too many minor details that would make these reports cumbersome and involved, much information that could be useful to the plant operator is often consolidated in such a manner as to have lost a considerable part of its value. To clarify this point, it may be stated that top management is most concerned with production figures and cost of production, while the plant operator is also interested in quantities of labor in man- hours and amounts of supplies used. Due to varying unit prices of labor and supplies, comparisons on a dollar basis alone are often misleading. With rising unit costs of the past few years now about twice as high as they were a few years ago, constant study of quantities involved is required to improve efficiency and productivity.

Jan 6, 1957

By Gerald Edmunds

THE development of "fiber" or preferred orientations, during the plastic deformation of metals, and the relation of such structures to the anisotropic characteristics of worked metals has become a subject of common knowledge among metallurgists. Very little has been published, however, relative to variations existent throughout the cross-sections of rolled strips,1 and the influence that such variations may have. This paper presents such a study on a rolled zinc alloy.2 The significance of small differences in surface structure is shown in relation to bending properties. Experience with zinc and its alloys has shown that the outer radius of the bend, which is subject to tensile deformation, is the common region of failure. In considering relations of structural characteristics to bending properties it will suffice, therefore, to consider the ease and possible extent of tensile deformation resulting from various orientations. It is necessary in this connection to assume that on the average the individual crystals of a polycrystalline material act substantially as if their movements were unobstructed by the surrounding grains. This assumption is not strictly valid, but the error involved is unlikely to affect seriously the qualitative conclusions derived from its use. The mechanism of the plastic deformation of zinc crystals has been described by Mark, Polanyi and Schmid3 and by Mathewson and Phillips,4 and is regarded as ' being accomplished by block movements or

Jan 1, 1931

By D. D. Pollock

The resistivity, temperature coefficient of resistance, and absolute thermoelectric properties of some binary terminal solid solutions of silver were determined. Equations are given which permit the calculation of these properties. CONSIDERABLE work has been done on the constitution and electrical conductivity of binary alloys of silver.1-l2 Some of these alloy studies are apparently complicated by doubtful chemical analyses. In some cases the limits of solid solubility are questionable. Those references which present electrical properties of binary silver alloys usually give just one particular set of characteristics such as conductivity (or resistivity). As a means of checking and extending this earlier work, an investigation was undertaken to describe and calculate the resistivity, temperature coefficient of resistance, and thermoelectric power of binary terminal solid solutions of silver. PREPARATION OF ALLOYS All of the alloys were made with silver containing less than 0.014 pet (by weight) of impurities. These materials were carefully weighed out into 225-g heats and melted in a high-frequency induction furnace. The indium, tin, and antimony systems were melted in Al2O3 crucibles, under a boric anhydride cover, and poured into split graphite finger molds. The aluminum, germanium, arsenic, lead, and bismuth alloys were melted in machined graphite crucibles, and they were also covered with boric anhydride and poured into split graphite finger molds. The alloys containing magnesium and manganese

Jan 1, 1964