Search Documents

A. W. AMBROSE, Washington, D. C.-Did you make any analysis of the amount of emulsion at the well and after you flowed it through a lead line to the storage tank? E. A. TRAGER.-B. S. can be formed in passing through a lead line by the friction due to the roughness of the pipe and the irregularities at the joints. R. W. MOORE.-Did you find the percentage of water to be limited to the percentage of oil in the emulsion which formed? E. A. TRAGER.- Yes, the percentage is about 67 percent. water and 23, per cent. oil. R. W. MOORE.-If you added more water would the emulsion be permanent? E. A. TRAGER.-Yes, it would be permanent, but the excess water would separate out. THE CHAIRMAN. (C. W. WASHBURNE, New York, N. Y.).-Did you use hot or cold water in these experiments?

Jan 12, 1919

By N. H. Cone

It is somewhat surprising that among the many mechanical devices that were brought into the State of Colorado, that the Brückner cylinders alone have stood the test for roasting ores. The brick walls of the Arey and Stetefeld furnaces have been remodelled into reverberatories and compound reverberatories, their binding and anchor irons have been forged into hoes and shovels, while the Crosby and Thompson cylinders have been rent by the ruthless hand of the foundryman searching for a tough piece of boiler plate. Two only of these furnaces remain in operation, of the large stock that came into Colorado by car-loads several years ago, and they occupy only a subordinate position to some reverberatories on the North Boulder Creek. But to-day there are in Colorado, in active operation, ten Brückner cylinders, and two or three more running part of the time. Dur-

By N. E. Cone

IT is somewhat surprising that among the many mechanical devices that were brought into the State of Colorado, that the Brückner cylinders alone have stood the test for roasting ores. The brick walls of the Arey and Stetefeld furnaces have been remodelled into reverberatories and compound reverberatories, their binding and anchor irons have been forged into hoes and shovels, while the Crosby and Thompson cylinders have been rent by the ruthless hand of the foundryman searching for a tough piece of boiler plate. Two only of these furnaces remain in operation, of the large stock that came into Colorado by car-loads several years ago, and they occupy only a subordinate position to some reverberatories on the North Boulder Creek. But to-day there are in Colorado, in active operation, ten Brückner cylinders, and two or three more running part of the time. Dur-

Jan 1, 1876

By Chester N. Truax

Still another shadow was cast over coal's largest market-the electric utilities-when President Johnson signed into law the Federal Clean Air Act of 1967. Air pollution-sulfur reduction-was thus brought into sharper focus as one of the central problems of the coal industry. Industry executives testified in both Houses of Congress to enable the lawmakers to develop a workable and economic law. The new legislation calls for the Secretary of Health, Education and Welfare to establish air control regions. After the regions are outlined the Department will publish air quality criteria on pollutants. Anticipating this legislation, the coal and utility industries have for the last several years been involved in extensive research programs to develop solutions to the air pollution problem. Even though the coal industry has been under strong attack for its part in adding contaminants to the atmosphere, it is by no means the major contributor.

Jan 2, 1968

By Richard L. Gordon, Charles J. Johnson

Electric power demand doubles about every ten years, and because of the associated burgeoning fuel requirements, power stations absorb over half of the coal output in the United States. Throughout the 1960's, demand for coal utilized to generate electricity grew at an average annual rate of 6.5% but coal producers held back greater expansion because they expected nuclear plants to proliferate faster than they actually did. Even so, the growth rate is expected to continue at the 1960's rate until at least 1976. The continuation of the 6.5% growth rate beyond 1976, however, will require additional orders for coal-fired plants during the early 1970's. In fact, plants consuming a total of 130 million tons of coal must be ordered in the next few years. If the requisite plants materialize, total 1980 coal output for electrical power generation will be approximately 600 million tons.

Jan 1, 1971

By C. F. Kelley

IT is no new experience for the distinguished subject of this presentation to be the recipient of honors conferred, to be eulogized for successful accomplish-ment, or to hear expressed with sincerity the admira-tion of his fellows. The objectives of his professional endeavor have taken him to many fields; the scenes of his labors have varied from the most remote corners of the globe to those which are close at hand; the universality of his experience is an epitome of modern life, impossible of occurrence in any other era. His career not only embodies to an unrivaled degree the opportunities of the contemporaneous epoch, but also exemplifies in the manner in which they have been transformed into successful accomplishments the pos-sibilities of our age. The many-sided career of our medallist is a composite. Tonight we deal chiefly with its phase for which this medal has been bestowed.

Jan 3, 1928

By T. Cuscino, D. D. Lane, C. Cowherd, T. E. Baxter

Three types of commercially-available dust suppressants, commonly used in the surface mining industry to control fugitive particulate emissions from unpaved roads, were tested in the laboratory for cohesive strength and resistance to reduced effectiveness by large water addi¬tions. Results indicate that each product tested varies in cohesive strength with a range of 34-300 kPa (5-44 psi). Total cohesive strength depends on the aggregate moisture content and the means by which the sample is dried. Results show that laboratory testing can be used as a decision¬making tool concerning the type of dust suppressant for a particular mining operation. Also, the road surface aggre¬gate moisture content u critical to successful dust suppres¬sant performance. Large water additions to the aggregate road surface after initial suppressant application can pro¬duce nondesirable results. A modified wet sieving analysis is presented to test the effect of water addition.

Jan 1, 1984

By Joseph W. Mills

In 1956 the discovery of nickel on Jumbo Mountain, Snohomish County, Washington, focused attention on this part of the Cascade Range, far more renowned for its timber than for its mineral resources. Hand specimens assaying as high as 13 pct Ni encouraged Discovery Mines Inc. of Mount Vernon, Wash., to stake 12 claims in Township 31 North, Range 9 East of the Willamette Meridian. The property was leased to Climax Molybdenum Co. in January 1957. Trenching, sampling, and geologic studies were carried out during the late summer of 1957 when most of the snow had disappeared. Although the deposits are only about four miles south of the logging town of Darrington and about two miles, as the crow flies, southeast of the end of a good gravel road from that town, all camp supplies and equipment were air-dropped, owing to the extremely rugged nature of the terrain.

Jan 3, 1960

By Byron S. Gottfried, Guan Qi Zhao, John W. Tierney

Equations for predicting the performance of vacuum filters and centrifuges used for coal dewatering are presented. These equations are the basis for a dewatering module which has recently been added to the Coal Preparation Plant Simulator developed at the University of Pittsburgh under the sponsorship of the Department of Energy. The module provides for mechanical degradation in the centrifuge; loss of fines to centrate or filtrate; changes in size and gravity distribution; changes in ash and sulfur content; as well as final moisture content of the dewatered product. Inputs to the module are the flow rate of the coal to be dewatered, a washability analysis of the coal, and parameters describing the operation of the vacuum filter or centrifuge. Typical results obtained using the module are presented. There are adjustable parameters which can be varied to match plant operation or experimental data if desired.

Jan 1, 1983

By P. R. Gage, R. W. Bartlett

SILICIDE coatings on refractory metals are often applied by transporting a silicon halide vapor to a hot metal surface where dissociation or hydrogen reduction occurs. The subsequent chemical reaction to produce the coating requires diffusion of silicon or the refractory metal through the in situ silicide layer. This solid-state diffusion process step is often slower than the vapor-transport step and, therefore, rate controlling. This situation is analogous to the parabolic oxidation of metals in which the oxidation rate is controlled by diffusion through the oxide layer. The purposes of this study were to 1) measure the rate of formation of MoSiz and MoSi2 coatings under conditions such that the silicide diffusion process is rate controlling and lower silicide compounds are not formed and 2) determine by a marker experiment whether silicon or the respective refractory metals are the principal diffusing species in the disilicides.

Jan 1, 1965

By David R. Maneval, Ralph A. Lambert, H. B. Charmbury

Subsidence, although it may or may not be apparent on the surface, is an inevitable consequence of deep coal mining and a frequent cause of damage to surface structures. Efforts to prevent subsidence go back many years, but there is still only one known antidote that is both technically feasible and predictable. This is the hydraulic or pneumatic stowing of solids-or flushing. In coal mines, however, flushing has been rarely used because it is considered the most expensive method of filling such mines, even though the reverse is true for ore mines. It is thus significant that the method has found favor in a comprehensive program the Commonwealth of Pennsylvania has undertaken to eliminate the hazards of abandoned coal mines within its jurisdiction. In "Operation Backfill," as the program is known, the Commonwealth has successfully used hydraulic flushing and fully justified the method economically.

Jan 4, 1967

By K. R. Y. Simha, W. L. Fourney, D. C. Holloway

An experimental investigation was performed to evaluate the role of stress waves in the pre-splitting operation. 3D birefringent Plexiglas models and the dynamic photoelastic technique were used to visualize the stress waves generated by the detonation. Simultaneous as well as sequential detonation of the explosive charges were investigated. The development of fractures and stress waves were recorded using a high speed multiple spark gap camera of the Cranz-Shardin type. The experimental data was analyzed and displayed-on a Lagrangian diagram to present an overall picture of the entire dynamic event. It was repeatedly observed in the tests that the time required for the completion of the pre-splitting operation as practiced in the field is of the same order as that for the transit time for the stress waves between the blastholes thereby revealing the highly elasto-dynamic nature of the event.

Jan 1, 1982

By C. W. Kempton

IF New England were located in some distant and almost inaccessible region, there is no doubt that its mineral resources would have been ere this well developed and generally acknowledged, but laboring under the disadvantage of nearness, it has been neglected. Its surface, moreover, is not cut up by mountains and canons, and the remnants of many of the old ridges are extensively covered by glacial drift. Having for the past ten months been engaged in the development of a. mineral district in Southeastern Maine, I would take this opportunity to lay before the Institute sketches of results, and try to give some idea of the formations as found. The Sullivan Mining District extends from the town of Franklin, through Hancock, Sullivan, and Gouldsborough, from northwest to southeast, about sixteen miles. A general idea of this locality may be gathered from the map accompanying. (Fig. 1).

Jan 1, 1879

By G. L. Hundley, R. E. Mussler, D. H. Yee, F. E. Block, R. S. Olsen

An anhydrous chlorination process for the recovery of copper from chalcopyrite was investigated. Pelletized concentrate was reacted continuously with gaseous chlorine in a vertical shaft reactor at 550° and 650°C. While the copper was withdrawn with the rest of the metals as molten chlorides from the bottom, 99-x% sulfur was distilled from the top of the reactor. The molten metal chlorides were pulverized and dropped continuously into an upward flowing stream of oxygen. Over 80% of the iron chlorides were converted to oxides in a vertical free-fall reactor at 800° and 900°C while the copper chlorides passed through unoxidized. Copper was recovered in powder form by electrowinning continuously from chloride solutions using a diaphragm cell. The product sloughed easily from a titanium cathode and showed no iron contamination. Current efficiencies and power consumptions averaged 77% and 1.24 kw-hr per lb.

Jan 1, 1974

An overland belt conveyor system installed at Simco-Peabody's mine near Coshocton, Ohio, is presently carrying coal three miles at an estimated cost of 4.499 per ton-mile. Installed by Link-Belt Co. in late 1961, this system transports coal from open pit and underground mining operations to the Conesville Power Plant. Simco-Peabody has mining operations over a considerable area just east of the Conesville Station. In 1960 the power plant completed plans to enlarge by adding a third boiler. As a result, Simco-Peabody was required to provide means to produce and handle more coal. The haulage equipment, which consisted of one 90-ton, five 60-ton and one 50-ton off- highway trucks, was too small to handle the increasing daily coal demands. Annual tonnage was approaching a million tons and in a few years would be well over that figure.

Jan 4, 1963

By J. A. Herbst, J. L. Sepulveda, J. D. Miller

Abstract-Lead cake, a zinc smelter flue dust residue, consists primarily of lead sulfate. Characteristic properties of lead cake were determined in order to aid the understanding of reaction mechanisms involved in bismuth removal from lead cake by sulfuric acid digestion. Sp gr (specific gravity) measurements, surface area measurements, and photomicrographs revealed that the particles of lead cake are quite porous and seem to consist of an agglomeration of submicron grains (0.4 pm) fused together in a manner similar to cement clinker. Analysis of experimental rate data, which was independent of particle size, indicates that the dissolution reaction involves two distinct, rate limiting steps. The initial stage of reaction appears to be limited mainly by intergranular diffusion of the reactant, hydrogen ion, while the latter stage of reaction appears to be controlled by diffusion of soluble reaction products through the reaction product layer of the individual grains.

Jan 4, 1978

By Kiyoshi Mizui

Processes for manufacturing prereduced iron pellets from iron ore dust occurring in iron works have recently begun on an industrial scale. Because of their high porosity and low mechanical strength, these prereduced iron pellets tend to oxidize again and disintegrate into fine particles during transportation and storage; this may result in such difficulties as decreased yield, undesirable work environment and heat generation during oxidation. A possible process for avoiding oxidation and disintegration of prereduced pellets is increasing the density through briquetting. The authors carried out briquetting tests under various conditions, attempting to find optimum briquetting conditions. They found that crushing prereduced pellets and adjusting the particle size to a certain range before briquetting increased the briquette strength and reduced the amount of binder needed. Oxidation resistance of briquettes and raw material pellets was compared in open air and at high temperatures. Briquettes showed superior oxidation resistance.

Jan 1, 1977

By J. W. Downey, A. E. Dwight, R. A. Conner

THE MgCu2 type Laves phase has been observed in the thorium-osmium and thorium-iridium systems. Two alloys corresponding to ThOs2 and ThIr, were prepared by arc melting a 5-g charge in a water-cooled copper. crucible. Both alloys were very brittle. X-ray diffraction patterns were obtained using filtered Cu and Co radiation with a Straumanis-type DeBye-Scherrer camera. The a,, values as shown in Table I were obtained by a Nelson-Riley extrapolation. The structure belongs to space group Oh7-Fd3m. Relative intensities for each of these compounds were calculated on the assumption that 8 thorium atoms occupy (a) positions and 16 osmium or irid-ium atoms occupy (d) positions. The calculated intensities are the product of the Lorentz-polarization factor, the multiplicity factor and F', the structure factor, neglecting the absorption and temperature

Jan 1, 1959

By M. J. deBastiani, John Kostuik

The Denison orebody, located on the north limb of a syncline, rests at depths of 800 ft in the northern end of the property to 3000 ft at the southern end, and has a composite dip of 19º, varying locally from 0º to 45º. It is composed essentially of two pyritized conglomerate beds separated by a varying thickness of quartzite. The thickness of the upper conglomerate reef of the main ore zone varies from 2 to 15 ft while the lower reef is from 2 to 12 ft. Mining, whether carried out over the entire section of the reefs and quartzite or by selective mining of the reefs, is accomplished by room and pillar methods, with an initial 67% extraction on the advance towards the property boundaries. The underground ore handling requirement in such an orebody has become one of the most challenging problems in mining.

Jan 8, 1966

By High Archbald

It is possible to construct a simple diagram of the earnings, or the production, of the men employed at a coal mine that will show not only if the conditions tend toward contentment among the men, but if the operating distribution of the work is correct. As earnings are the greatest cause of discontent, even exceeding all the other causes, if contentment exists in the matter of earnings, the likelihood of other discontents flaring up is greatly lessened. The basis of such a diagram would be the Gaussian curve of the normal variation in human ability. Such a curve has long been recognized. H. L. Moore,' in discussing the quantitative relation between wages and ability says: "It has been pointed out that industrial efficiency is dependent upon physical, mental, and moral qualities, and these qualities . . . there is good reason for regarding as being distributed according to the Gaussian law.

Jan 1, 1925