Search Documents

By Owen Thornton

Recently equations have been presented by Rose and Bruce' and by Rose², showing how the relative permeability of a reservoir rock may be determined from the capillary character of the rock. In particular, equations were developed to show the relationship between capillary pressure and the effective permeability to the wetting phase in a poly-phase flow system. The equations are as follows (nomenclature the same as in the Rose and Bruce paper) Rose and Bruce assume that the average length of path (L,), which the wetting fluid follows in flowing through a porous media is independent of the saturation to the wetting phase, so that 1 is a constant dependent only on the k rock, and the permeability to the wetting phase is a function of the saturation and of the capillnry pressure: In measuring the flow of ekctric current through partially saturated core samples, it has been observed that the electrical resistance usually is not a simple linear function of saturation. This fact indicates that the average length of path in the flow of electric current is not independent of saturation, but rather that the tortuosity of the path depends upon the average saturation to the conducting fluid as well as upon the characteristics of the rock. itself. Inasmuch as the flow of fluid and the flow of electric current in many respects are analogous, it may be indicated further that the length of path for fluid also may not be independent of saturation. The following relationship can be derived to express the resistance to flow of electric current through a core sample partially saturated with conductive wetting phase, the non-wetting phase being non-conductive: where L is the average length of path followed by the current in flowing through a length L of partially saturated core, where L is the length of current path when the core is fully saturated, and where Rs and R, are the specific resistivities of the partially saturated and saturated core sample, respectively. It will be noted that R., the specific resistivity of the core sample when S, = 1.0, is equal to the "formation resistivity factor"' multiplied by the specific resistivity of the saturating fluid. If it be assumed that the average lengths of path for fluid flow and for the flow of electric current are the same, then equation (5) may be combined with equations (l), (2) and (3) to give the following relationship: The above equation suggests including a correction for tortuosity when calculating the relative permeability of a reservoir rock to a wetting phase. The correction factor may be obtained from the resistivity-saturation relationship. For instance, the following calcu- lations are obtained for the unconsoli-dated sands described by Leverett Kw Kw Sw R°/Rs Pt/Pc¹ (Calc.) (Obs.) 0.30 0.08 0.88 0.02 0.0 0.40 0.16 0.94 0.06 0.04 0.50 0.27 0.97 0.14 0.11 0.60 0.40 0.98 0.26 0.21 0.70 0.53 0.98 0.39 0.35 0.80 0.68 0.99 0.57 0.54 0.90 0.84 0.99 0.77 0.76 1.00 1.00 1.00 1.00 1.00 It will be noted that the agreement between the calculated points and the observed data is rather good. Further investigation of the above method for obtaining relative permeabilities may be merited. For many sands within specified ranges of saturations the following relationship has been found to hold approximately': — =SW"......(7) Rs The exponent n in the above equation has been found to equal two for many sands so that equation (6) reduces to the following: The writer acknowledges the permission of The Texas Co. to submit this note for publication. 1. Walter Rose and W. A. Bruce—Jnl. of Pet. Tech., Vol. 1, No. 5, p. 127 (1949). 2. Walter Rose—Jnl. of Petr. Tech., Vol. 1, No. 5, p. 111 (1949). 3. G. E. Archie— -Trans. AIME, 146, 54 (1942). 4. M. C. Leverett— Trans. AIME, 142, 152 (1941). 5. M. C. Leverett—Trans. AIME, 132, 149 (1939).

Jan 1, 1949

By John E. Young

U.S. Steel Corp.'s Winifrede mine is operated by Lynch District in the mountainous region of eastern Kentucky. This region is characterized by narrow finger ridges and precipitous slopes, which present both an opportunity and challenge in the design and selection of coal-handling facilities for the movement of coal from the section belts to the railrod cars. Lynch District selected diesel-powered locomo¬tives and 100-ton articulated cars capable of negotiating sharp curves. The drop¬bottom mine cars are equipped with longitudinally hinged doors that are auto¬matically opened and closed. Lynch District selected a large-diameter steel-lined borehole for lowering the coal approximately 1000 ft from the seam level to the valley floor railroad load-out point. Taking advantage of gravity, the presized coal is "lowered" vertically approximately 720 ft to existing entries of a previously abandoned mine. The coal is then conveyed horizontally into storage. The coal¬handling facility from the mine-car dump to the railroad load-out point is fully automatic through use of tone control. TV cameras are installed along the facility to continuously monitor the strategic points. The diesel locomotives are either directly operated or remotely radio-controlled, depending on the functions Per¬formed. U.S. Steel Corp.'s Winifrede mine is operated by Lynch District in the mountainous region of eastern Kentucky. This region is characterized by narrow mountain ridges and precipitous slopes which present both an opportunity and challenge in the design and selection of coal-handling facilities for the movement of coal from the section belts to the railroad cars. The narrow finger ridges precluded use of under¬ground haulage and, thereby, presented the opportunity to use high-capacity equipment on the outside bench. The precipitous mountain slopes, steepest at the Wini¬frede seam horizon, presented a challenge to select a solution for lowering the coal approximately 1000 ft from the seam level to the valley floor railroad load-out point. It was evident from the start of planning that these two factors predominated; namely, rail haulage and coal lowering, and solutions to these would determine the final design of the Winifrede mine coal-handling facilities. The Winifrede mine derives its name from the Wini¬frede Seam which comprises the total reserve recov¬erable from this facility. The seam is 5 ft high with a good siltstone bottom and competent shale or sandstone roof. The seam is at an elevation of 2700 ft where the mountain ridges are long and narrow. This configuration of the reserve was ideal for conveyor belt installation to transport the coal from the working face to the outside bench. The preclusion of underground rail haul¬age permitted an opportunity to review the type of locomotive power and to select high-capacity equipment without the limitations associated with underground systems. Since the basic electrical design of the mine was al¬ternating current, with rectification to direct current for shuttle cars required only in the face areas, there was no point in bearing the burden of additional cost of dc trolley installation. And, since the haulage would re¬quire only a few tunnels to negotiate sharp points and to reach the back side of the reserves, diesel power was selected for the haulage locomotives. To provide stability on the almost continuously curv¬ing track and to provide the maximum width of haul¬age equipment, both locomotives and mine cars, stan¬dard railroad gage was chosen to offer the largest choice of equipment. The decision was made to select a standard 45-ton railroad diesel locomotive but to lower the cab height to reduce tunnel excavation requirements. The mine car was the next challenge. Past experience in Lynch operations indicated that drop-bottom cars would be a successful application with the free-flowing coal. The search was for a drop-bottom car within the dimensions of the locomotive to discharge the coal in the shortest time. Numerous types were considered and visits made to various sites to observe cars in operation.

Jan 1, 1972

By Lawrence H. Van Vlack, Otto K. Riegger, Gerald I. Madden

The microstructural variations of periclase (MgO) in the presence of oxide liquids are examined under the steelmaking variables of: 1) temperature, 2) liquid composition, and 3) FeO additions under different oxidation levels. Attention is given to the distribution of the phases, both liquid and solid, and to the growth of individual crystalline grains. Silicate liquids penetrate more extensively between individual periclase grains than do liquids containing high percentages of Fe2O3 Higher MgO solubilities in the liquid and lower MgO contents of the solid favor more rapid grain growth. The presence of a second solid phase reduces the periclase grain growth rate and increases the amount of the solid-to-solid contact within the oxide microstructures at high temperatures. The service suitability of a refractory depends on many factors. Two are of major importance and include 1) the thermal resistance to melting, and 2) the mechanical resistance to loads at service temperatures. Neither is a simple consequence of the service temperatures because service conditions will alter compositions, produce partial melting, and induee phase changes. Consequently, the equilibrium phase relationships have been rather thoroughly studied and give a knowledge of the thermal resistance to melting, but do not give full information about the mechanical properties because two refractories with the same types and quantities of phase may have different microstructures. Although variations of microstructures with time, temperature, and composition have been subjects for extensive investigation in metals, only a limited amount of comparable microstructural work has been performed for refractory materials.' This study was an attempt to evaluate some of the consequences of service parameters upon the microstructures of refractories so that bases may be established for the analyzing of high temperature mechanical properties. Periclase (MgO) was chosen as the refractory oxide; variables included those which are encountered under steelmaking conditions such as 1) temperature, 2) liquid composition, and 3) FeO additions under various oxidation levels. Specific attention was given to the distribution of the phases, both liquid and solid, and to the growth of individual crystalline grains. The most closely related work on microstructures of polyphase materials is that of Van Vlack and Rieg-ger2 on the microstructure of magnesiowüstite [(Mg,Fe)O] in the presence of silica. In that work which pertained to solid solutions with less than 40 pct MgO, most of the quantitative work was performed on FeO microstructures. The chief conclusions concerning these relatively low-melting oxide solids were as follows: 1) the rate of crystalline grain growth is inversely proportional to the grain diameter, 2) grain growth proceeds more rapidly at higher temperatures but is slightly retarded by additional liquid content, and 3) a Silicate-containing liquid penetrates as a film between the individual magnesiowüstite grains independent of time, temperature, amount of liquid, or the MgO/ FeO ratio. The above observations are in contrast to prior work3 on the microstructure of silica in the presence of iron oxide-containing liquids where the liquid does not penetrate as a complete film between solid grains. The phase relationships for the compositions of the present work are shown in Fig. 1 which is a summary of the work of several investigators.4 Of importance is the fact that CaO forms a more stable structure with SiO2 and Al2O3 than do either MgO or FeO. The oxygen potential has little effect on periclase unless iron oxide is also present. The iron oxide is ferrous at moderately low oxygen levels, changing to ferric as the Oxygen potential is increased so the spinels, magnetite, and magesioferrite are formed.5 These two phases are relatively stable in air at steelmaking temperatures. I) EXPERIMENTAL PROCEDURE ractory were made with reagent grade Oxides. The magnesium oxide used was 99 pct MgO after ignition, and the iron oxide raw material had a minimum content of 99 pet Fe2O3. The CaO, SiO2, and A12O3 were also reagent grade raw materials. After mixing, the required compositions were pressed into pellets at a minimum pressure of 5000 psi to insure compaction of the raw materials and prevent excess void content. A silicon carbide element tube furnace was used with thermocouple control for sin-

Jan 1, 1963

By R. J. Evans, A. G. Revesz

Silicon films have been grown by chemical reaction on (111) silicon substrates. The surfaces were examined by various microscopic and interfero-metric methods. Surface structures are classified into two groups depending on whether the angles between the bounding planes and the (111) surface are small (<3 deg) or large (> I0 deg). A layer-gvowth mechanism is postulated to explain the topography and the influence of growth parameters. Growth proceeds by lateral expansion of the (111) layers in (211) directions, thereby forming steps. The step edges are perpendicular to the direction of expansion and are thus along (110) directions. Step bunching md surface nucleation both play an important role in modifying the flow pattern and in the step regeneration. These are influenced ver?) much by impurities, especially oxygen. Although the growth is a result of a surface-controlled ga: reaction, it is very similar to growth from an impure solution. OVERGROWTH ("epitaxial growth") of silicon is important and widely used. During the past years several investigators have observed various topographical features or so-called faults on the grown films. A study of the surface morphology gives some insight into the growth mechanism. I) EXPERIMENTAL Silicon films have been grown on silicon substrates by a method described by Theuerer.&apos; Silicon is formed by reduction of SiCl, in hydrogen. The rate of incidence of SiC1, was varied between 5 x 10"6 and 2 x 10&apos;4 moles min-&apos; cm-&apos;. The mole fraction of Sic4 in the Hz-SiCL mixture was about 5 x X Both the rate of incidence and the mole fraction were calculated on the assumption that the Hz bubbling through the SiC1, reached equilibrium saturation. Assuming uniform velocity distribution, the linear velocity of the gas in the reactor tube was estimated to be 2 cm sec-l. The temperature of deposition was varied between 1070" and 1260°C. Chemically polished p-type silicon wafers of 20 to 100 ohm cm resistivity were used as substrates. These were within 1/2 deg of a (111) orientation. The thickness of the grown n-type film was determined by two methods: a) measurement of the depth of the p-n junction taking into account the junction shift due to diffusion, b) measurement of the traces of stacking-fault tetrahedra on the (111) plane.&apos; The agreement between the two methods was better than 20 pct. The rate of growth varied between 0.2 and 4.0 pmin-&apos;. The formed films were examined by reflection and light-section microscopy, and by multiple-beam interferometry. Phase-contrast illumination revealed height differences of about 30A. For measuring heights greater than 1 p a light-section microscope3 was used. The resolution by multipke-beam interferometry4 was between 50 and 100A. Crystallographic directions on the surface were determined by X-ray and from the orientation of etch pits and stacking faults as revealed by Dash etch (I part HI?, 3 parts HNOJ, and 12 parts CH3COOH). Some specimens have been investigated by electron microscopy. Platinum-shadowing and carbon-replica techniques were used to show the fine topography and reflection diffraction to determine the structure of the grown layers. 11) RESULTS The topographical features can be classified into three groups. he first group is comprised of fine ridges (striations). The second group consists of structures, which are bounded by planes making angles of less than 3 deg with the (111) surface. They are, therefore, vicinal planes. Structures which closely resemble growth or etch pyramids from the third group would normally be bounded by perfect low-index crystallographic planes. In this case they are deformed. The angles between the bounding planes and the (111) surface are generally larger than 10 deg. The fine ridges are present, even on the smoothest surfaces, as shown in Fig. 1. They are along a (110) direction. The height differences could not be resolved with interferometric techniques. The basic characteristic structures of the second group are depressions and hillocks. These are bounded by three planes, two of them with larger slopes than the third one. The edges between the planes, as projected to the (111) surface, point in (211) directions. Various habits of these structures are shown

Jan 1, 1964

By R. L. Bleifuss

The object of this study was to evaluate the oxidized taconites of the western Mesabi iron range and to establish a correlation between the various basic taconite types and their concentratability. The initial work included a study of the original mineralogical and stratigraphic facies of the fresh taconite and traced the oxidation and leaching patterns developed during the conversion of this material to oxidized taconite. Subsequent studies have extended this work to include the semitaconites and also the wash and heavy media ore types widely developed in the area. Each basic original mineralogical facies or taconite type produces during alteration an equivalent secondary oxidized facies which has a unique mineralogical composition and texture. These control the concentratability of the oxidized taconites. Actually the influence of the original mineralogical composition of the iron formation extends even further and determines whether the most likely product of oxidation and leaching will be a wash ore or a heavy media ore and even to the direct shipping ores where the ratio of hematite to goethite is largely determined by the original taconite type. The relationship between original taconite, oxidized taconite, semitaconites, and wash and heavy media ores is briefly summarized in Table I. The terms are not precise and in some instances tend to overlap. The table is intended to point out only the essential differences between the various materials. The original taconite was dominantly composed of mixtures of magnetite, iron carbonate, iron silicate, and quartz (chert). In a few thin stratigraphic units, hematite was present as an original constituent. The alteration of the original taconite to oxidized taconite has resulted from the circulation of ground waters through an initial fracture system related to minor structures in the iron formation. The chemical reactions have involved the oxidation and decomposition of original minerals such as magnetite, iron carbonate, and iron silicates to hematite or goethite. The alteration at this early stage is characterized by pseudomorphic replacement of the original minerals by oxidation products although retaining the major textural features of the original taconite. There was very little secondary migration of iron at this stage and the total iron content of the rock has been only slightly increased. Further alteration of this material to form a semi-taconite, a wash or a heavy media ore, involves extensive removal of silica in solution and significant redistribution of iron units. Wash and heavy media ores are developed by the growth of coarse secondary iron layers, dominantly goethite, coupled with the removal of silica in solution and decomposition of the cherty layers. This paper is concerned primarily with the materials classified as oxidized taconites which are characterized by oxidation of the original mineral constituents with little secondary enrichment. The area studied, shown on the index map, Fig. 1, extends some 30 miles along the strike of the Biwabik formation roughly from Hibbing to Coleraine. This study was greatly facilitated by the basic stratigraphic and mineralogical studies of Gruner1 and white2. The bulk of the material in this presentation represents a portion of the author&apos;s contribution to a study sponsored by the Great Northern Railway on the oxidized taconites of the western Mesabi.3 METHOD OF APPROACH A total of 106 drill holes, representing some 30,000 ft of drilling, were examined and sampled. The drill holes were logged and some 1500 composite samples were prepared for chemical analysis and bench scale metallurgical tests. These samples were analyzed for total iron and ferrous iron; and magnetite iron was determined by a standard Davis tube test at minus 200 mesh. Standard reduction roast tests using 150-gram samples of minus 10 mesh material were made on these 1500 composite samples with a mixture of H2, CO2, N2, and H2O at a temperature of 650°C. This roasted material was pulverized through 150 mesh and concentrated in the Davis tube. The iron recoveries and concentrate grades obtained on the roasted products were used to assess the concentratability of the oxidized taconites. Detailed mineralogical work was done on thin sec-

Jan 1, 1964

By A. A. Brant

In this presentation, concepts of the formation and evolution of the universe, the earth, and the cyclic civilizations of man are broadly outlined. The 5 billion or more years of the universe and the 4% billion years of the earth are contrasted to the 5000 years of modern society and the 100 years of objective scientific breakthrough. THE UNIVERSE Let us start back as far as possible, to the beginnings of this universe, some 5 billion or more years ago. This is a time interval that can be crudely underestimated by the moon-earth tidal friction effects that have increased the length of the day by about 1/1000 second per century — from a 5 to 7 hour day to its present 24 — and have moved the moon away at 5 inches per year to its present 240,000 miles. The oldest stony meteorites from interplanetary space give an age dating of some 4.6 billion years, approximating the time of formation of our earth. Further, certain stars pulsate, the period of pulsation being related to their absolute brightness. Measuring apparent brightness and comparing, gives the distance away. Thus Hubble and Shapley of Harvard, from 1925 on, were able to show that the universe reached as far as our telescopes could scan. The Doppler shift of the hydrogen red lines could only mean that the nebulae, or galaxies, were moving away away at velocities increasing with their distances, by 180 km/sec velocity increase for every million light year&apos;s distance. In short, the universe is expanding like an exploded bomb. Comparing the velocity increase per million light year&apos;s distance again indicates a zero time of some 5 billion years&apos; Thus it appears that this universe had a finite beginning. Physical measurements and present theories permit some picture of our universe&apos;s birth. We know since Einstein that many forms of energy are equivalent, e.g., mass, and electromagnetic radiation, aspects of which are heat and light. Now with expansion, radiation density or equivalent mass decreases as a length factor to the 4th power, while mass as matter decreases at a length factor cubed. The temperature in outer space is now perhaps 100° absolute and the radiation mass equivalent is but 1/1000 the rarefied interstellar gas densities. Decompressing the universe to a starting point, however, raises temperature more rapidly than mass density, and results in a high radiation mass energy fraction, which since it is proportional to temperature to the 4th power suggests a zero point temperature of several billion degrees, brighter than any sun. "Let there be light and there was light," according to Genesis 1-3. Now what further initial conditions must there be to explain the relative abundance of the elements in the universe, which by spectral analyses of the earth&apos;s crust, stony meteorites, and the sun and stars is surprisingly uniform throughout. Some 55% of all cosmic matter is hydrogen, some 44% is helium and only 1% is made up of all the heavier elements in much the same proportions as on earth. These latter decrease logarithmically in abundance up to atomic weight 100, then level out. This consistent abundance distribution of elements in the universe may be generally explained by taking at Time Zero a hot neutron gas of density about 10-3 grams per cc, at a temperature of several billion degrees Centigrade, with a high radiation energy fraction. Generally neutrons break down into positrons and electrons within about ten minutes, but at the initial high temperature and radiation pressure would recom-bine. However, with rapid expansion and decrease of temperature and pressure, the neutron disintegration would run uncompensated and aggregation would result from neutrons and protons uniting in different degrees of complexity. The total calculated element aggregation time would be about one hour while the temperature still remained above one billion degrees. The element abundances formed would depend on density of the nuclear gas, simplicity of the atom formed, and the neutron capture cross section. Thus a higher density

Jan 1, 1964

By P. Somasundaran, D. W. Fuerstenau

The length of the collector is found to influence the flotation of the mineral even at incipient conditions, which are below the concentration at which interaction at the solid-liquid interface begins to take place to form hemi-micelles. To study this dependence, concentration for incipient flotation of quartz was determined as a function of pH with collectors of various chain lengths. The observed effect of chain length on flotation is ascribed to that of collector adsorbed on the bubble surface. In previous studies, it was shown that at low concentrations the alkyl collector ions adsorb at the solid-liquid interface as individuals.&apos;&apos;2 At higher concentrations, the collector ions adsorbed at the solid-liquid interface associate with each other to form two-dimensional aggregates called hemi-micelles. Above the hemi-micelle concentration, the length of the hydrocarbon chain is extremely important since the hydrocarbons are in effect removed from water during the association, making the energetic conditions more favorable for adsorption at the interface. Because of this enhanced adsorption, one observes a very rapid increase in flotation associated with the hemi-micelle formation at the solid-liquid interface. However, a dependence of flotation on the chain length at concentrations below that required for hemi-micelle association was also observed,&apos; and this cannot be explained by the above mechanism which postulated hydrocarbon chain interactions only at the solid-liquid interface. This prompted an investigation into other possible reactions of the hydrocarbon chains and an examination of the conditions at the bubble surface involved in the flotation system and how these observations might explain the reactions at the solid-gas interface which cause the particle-bubble attachment required for flotation. To obtain more information on chain length effects, flotation, under incipient conditions, was tested by vacuum flotation techniques. The collector-concen-tration-pH relationships for flotation of quartz with alkyl ammonium acetate collectors was delineated by observing the pH at which quartz particles begin to float to the liquid surface. By investigating flotation as a function of pH, it was also possible to study the effect of neutral molecules on incipient flotation conditions, since the aminium ions hydrolyze to amine molecules at higher pH values. EXPERIMENTAL WORK Brazilian quartz specimens were crushed and sized, and the 270 x 400 mesh fraction was used for flotation studies. The samples were leached with concentrated hydrochloric acid until no coloration of the acid occurred. The leached material was washed free of chloride ions and stored in distilled water. The vacuum flotation technique developed by Schuhmann and prakash3 was used to determine the critical pH-concentration curves. This method, which can be used to delineate conditions for incipient flotation, is fairly simple and rapid. About 0.5 gm of 270 x 400 mesh quartz was placed in a 100 ml graduated cylinder which was then filled to the 100 ml mark with the collector solution made from high-purity alkyl ammonium acetate salts. The water used for the test was conductivity water saturated with air that had been passed through a cleansing train consisting of Drierite, Ascarite, a water wash bottle, and a trap. After the pH was adjusted, the cylinder was then conditioned for thirty minutes. In the tests where an acid pH was desired, sufficient acid was added before the collector solution to avoid any effect due to slow desorption of collector from the quartz surface. After conditioning, vacuum was applied to the system and the flotation or nonflotation of the quartz was noted. The pH at which the quartz particles began to float to the liquid-gas interface was taken as the critical PH. Critical pH curves were thus determined for different concentrations of the various collectors. Hallimond tube flotation data were taken from the authors&apos; previous publication1 for correlation with that from the vacuum flotation. RESULTS AND DISCUSSION The results of vacuum flotation studies for determining critical pH-concentration curves, i.e., curves which delineate conditions for incipient flotation, are shown in Fig. I. In generaI, all the curves exhibit an upper and lower pH limit between which flotation will

Jan 1, 1969

By J. S. Marsh

OPPORTUNITY to pay tribute to the memory of Professor Henry Marion Howe is a strenuous assignment as well as an honor. Upon recalling Howe lecturers and lectures of the past 25 years, glancing over the list of those earlier, and rereading Howe&apos;s books, I arrive at several conclusions: 1—Many lecturers either worked under or knew Professor Howe. 2—It is virtually impossible to pick a subject on which Professor Howe did not touch. 3—There is precedent for a technical paper based upon pursuit of a single subject. 4—There have been listening lectures and reading lectures. There is solid comfort only in 2: the subject field is wide open. I did not know, nor even ever saw, Professor Howe, so can supply no fitting reminiscence. As a college student I was dimly aware that he counted among the giants. Fuller appreciation of his stature came with reading his books and papers, growing acquaintance with some of his associates, and the intrinsic dignity of the climax of the Annual Meeting, beginning at four o&apos;clock of a Thursday afternoon in the auditorium of the Engineering Societies Building in New York. As for producing the technical paper sort of thing, it is my lot to have reached an age and assignment such that to do so would be to filch information from those who did the work and whose story is theirs to tell; for this I have no enthusiasm. As for the final conclusion, Professor Howe was one of the chosen few so highly expert at expository writing that he could produce a lecture or paper that reads as though it would also have listened well. One of his tricks was the free use of words not ordinarily part of the technical vocabulary, provided that such words were likely to communicate most precisely what he had in mind. How wonderful it would be for all who must read reports by the ton if ability at exposition could be taught with the effectiveness open, say to, differential calculus! Perhaps Professor Howe should be required college reading even if for no other reason than to prove that technical writing need be neither dull nor diffuse. My assignment is clearly still strenuous. Another point to consider is the fact that metallurgy is now so tremendously diversified that hope of finding a topic of universal appeal is negligible, even if one were competent enough to be permitted free choice. That which follows is, therefore, a compromise composed of necessity and of the obligation to attempt to avoid boring to slumber those of you who are not especially interested in the general subject chosen. The Iron and Steel Div. is now essentially a process metallurgy division, heavily concerned with the smelting of iron and the making of steel. The American Iron and Steel Inst. figure for present steel capacity of this country is 125,828,310 net tons; how this is divided among processes is indicated by the production totals for 1953, shown in Table I. The glamor girls and boys make the front page and so it is with steelmaking processes. If there is an Antarctic Daily Bugle, it undoubtedly has carried stories of revolutionary development, such as oxygen processes and vacuum melting, and stories of the incomparably rosy destiny of electric arc melting. All such certainly have their place and their future; meanwhile, it is the sturdy and old reliable open hearth that accounts for the bulk of production reported back on the financial page, and it is the old reliable that is most likely to continue to account for the bulk for some perfectly sound raw material, technologic, and economic reasons. This, plus the fact that next year marks a centennial (for it was in 1856 that Frederick and William Siemens conceived the regenerative open hearth), is reason enough to talk about open hearth furnaces, but is not the real one. The real reason is that in some years of association with open hearths, I have accumulated—in addition to a genuine liking and respect for them—certain odds and ends of fact and fancy that this lecture provides a unique chance

Jan 1, 1956

By H. T. Sumsion, A. U. Seybolt

The results of an investigation of vanadium-rich V-O solid solutions are presented, indicating the structure and lattice parameters of two solutions, a and ß, and their approximate temperature-composition existence. The a solution is the terminal body-centered cubic one, and contains up to 3.2 atomic pct 0. The ß solution has an ordered body-centered tetragonal structure, is formed at 1270°C, and exists from about 15 to 22 atomic pct 0. From the evidence available, the various phase boundaries have no appreciable temperature dependence. Evidence has been found for a polymorphic transformation in pure vanadium at 1550°C. IN an earlier investigation&apos; dealing with the preparation of pure vanadium by calcium reduction of the oxide, it was found that small amounts of oxygen drastically reduced the ductility of the metal. Because this effect was so marked, it was decided to make a study of the solubility of oxygen in solid vanadium. This report deals principally with this solubility and the nature of the phase relationships in the vanadium-rich region, particularly at temperatures below 1300 °C. However, during the investigation enough data on the V-0 system were obtained to make it appear worthwhile to present a tentative phase diagram up to the composition VO. The only significant prior work found on this system are the contributions of Klemm and Grimm,&apos; and Mathewson et al.3 Klemm and Grimm prepared a wide range of V-O compositions by powder techniques including the compositions VO.l, VO.2, VO.3 and VO4 (9.1, 16.8, 23, and 28.6 atomic pct 0, respectively). The first three compositions were found to consist of a body-centered tetragonal solid solution, while the last also showed lines of VO (NaCl structure). They found that the parameter c, increased and the parameter a, decreased with increasing concentration of oxygen. For their composition VO.27, or about 16.8 atomic pct O, they cite the values a, = 2.948A, c, = 3.53A, and c/a = 1.2. Klemm and Grimm made no attempt to determine the solid solubility limit nor to construct a phase diagram. They did, however, give some data on the homogeneity range of VO, and they proposed a structure for the body-centered tetragonal solid solution; these points will be taken up later. Materials and Preparation of Samples The vanadium used in this investigation was prepared in the laboratory by the method previously mentioned.&apos; A typical analysis is as follows: Fe, 0.007 pct; Si, 0.02; Ca, 0.06; C, 0.224; O2, 0.044; N,, 0.0017; H2, 0.003; and V, 99.34 ±0.3 (assay). The vanadium assay is probably low by about the error given. The impurities total about 0.36 which, if subtracted from 100, gives a purity of about 99.6. At the time material was being prepared for this work no suitable technique was available for melting vanadium without appreciable contamination. The procedure adopted therefore was to cut the calcium-reduced regulii into slices which were then rolled to strip about 0.025 in. thick for oxygen diffusion. Pieces of rolled vanadium of approximately 0.025xY4xl in. and weighing about 0.3 g were suspended in a vertical fused-silica tube which was part of an ordinary gas absorption apparatus. The silica tube was heated by an electric resistance-tube furnace which could be raised around the silica tube or lowered away from it as desired. This apparatus had no novel features which require detailed description. Other than the silica tube and furnace, it consisted of a glass system evacuated by a liquid nitrogen trapped mercury diffusion pump, a mercury-operated gas burette, a McLeod and a Pirani gage, and a mercury manometer. It was also equipped with suitably located stopcocks for isolating various parts of the system; the vacuum ordinarily attained was between 10" and 10-6 mm of mercury. Oxygen generated by decomposing MnO2 was passed through anhydrous magnesium perchlo-rate before introducing it into the gas burette and thence to the absorption chamber.

Jan 1, 1954

By P. L. Rittenhouse, M. L. Picklesimer

A rapid and seniquantitative method of determining prefered orientation on large numbers of. Zircaloy-2 specimens was desired. knoop microhardness measurerrzetzls were irvestigated as a solldtion to this pro6lem. The variation of Knoop microhardness measurerlerzts on selected planes as a function of &apos;irzdenle axis relutilje lo cryslallograplzic or fabrication divectals were used to corzstrrcl a polar coordinate hardness contour map. With use of an empirical relationslip between the single-crystal hardnesses and those of the polycrystalline material conentional pole figures could be constructed which compare favorably also obtained. To determine preferred oriention qualitatively from hardness data requires a minimum of twelve measurements per plane on three, preferattention to grain size, specimen prepartion, and in-rreinetzt, and analjlsis is of the order of- 45 to 60 rrin. THE design of structures from Zr alloys requires consideration of preferred orientation and the resulting anisotropy of mechanical properties. Rapid and semi-quantitative methods of evaluating anisotropy and of determining preferred orientation are needed for quality control and for examining the large number of test specimens required in development programs. The variation of Knoop microhardness with indenter orientation has been studied in single crystals of several hcp metals including titanium.&apos; beryllium,&apos; magneium, and zinc.4 The maximum hardness observed on any crystallographic plane other than the basal plane invariably occurred when the long axis of the Knoop indenter was either parallel or perpendicular to the projection of the [ OOOI.] direction on the plane of examination. When the major slip mode was (0001)(i2i0j the maximum hardness occurred at the parallel positio! but when the operating slip system was {10i0) (i210) the hardness was a maximum perpendicular to the [0001] projection. A minimum hardness was always observed at a rotation of 90 deg from the maximum. It follows that the orientation of the projection of the [0001] can be determined on any non-basal plane by making hardness measurements at a number of indenter orientations. The determination of the orientation of the [0001] projection on two non-parallel, preferably orthogonal, surfaces of the specimen will allow location of the [0001] direction in the specimen. It seems possible that such measurements could be used to examine, at least qualitatively, the preferred orientation existing in polycrystalline hcp materials. An investigation of the microhardness anisotropy in Zircaloy-2 was undertaken to ascertain whether these measurements could be used for this task. EXPERIMENTAL PROCEDURE Single crystals of Zircaloy-2 were grown by an a-8-a annealing sequence using electron-beam heating.= The orientation of the crystals was determined by a conventional back-reflection Laue technique. The crystals were then mounted on a goniometer head and the desired crystallographic faces were milled and chemically polished. Polycrystalline Zircaloy-2 specimens were prepared from fabricated sheets or plates. Inverse pole figures for these materials were obtained using the X-ray diffraction techniaue described by Jetter, McHargue, and illiams.&apos; A Wolpert-Greis Micro-Reflex hardness-testing machine was used to make the Knoop microhardness measurements. The single-crystal and polycrystalline specimens were loaded to 0.5 and 2.0 kg, respectively. Determination of the scatter of hardness numbers as a function of applied load for several indenter orientations on several specimen surfaces showed that the loads selected were the lightest consistent with minimum scatter. Heavier loads did not appreciably decrease the scatter and produced hardness impressions too large to be conveniently measured with the equipment used. Seven crystallographic planes of the single crystals were examined, while six planes of examination were used in studying Zircaloy-2 polycrystals. The specimens were rotated 10 to 15 deg after each measurement and from four to eight impressions were made at each angle of rotation. RESULTS The two angles which were used to relate crystallographic directions and planes in the hcp cell to the planes of examination of the single crystals are shown in Fig. 1. 8 is the angle between the c axis. [0001]. and the normal, N, to the plane of examination. a is the angle between the long diagonal of the Knoop indenter and the projection of the c axis on the plane of examination. For exampIe, if P = 90 deg and a = 0 deg, the plane of examination is of the family

Jan 1, 1967

By G. L. Tufford, R. L. Bleifuss

Low-grade manganiferous iron ores of Minnesota&apos;s Cuyuna Range, in general, do not respond to conventional mineral dressing techniques because of their fine-grained texture. Reducing these ores to magnetite with subsequent magnetic separation and flotation have not given satisfactory results because, in many instances, concentrate grade and manganese recovery are low. Metallization of iron and concurrent reduction of higher manganese oxides to MnO, as in the R-N process, followed by recovery of iron by magnetic separation and manganese by leaching, seems to be a technically feasible process. High-temperature x-ray diffraction studies show that solid-state reactions between iron and manganese, with the formation of intermediate iron-manganese oxides, occur during reduction and affect recovery of both iron and manganese from the final product. Solid state reactions also occur between FeO, MnO, and SiO, at temperatures as low as 900°C. The kinetics of these reactions are such that they become an important factor in the treatment of ores by the R-N process. These investigations suggest a temperature and gas composition cycle that would maximize both iron and manganese recovery. During the past ten years, iron ore shipments from the Cuyuna Range of Minnesota have decreased sharp1y. Because of adverse grade, structure, and cost, many Cuyuna ores are no longer competitive with high-grade foreign ores and domestic pellets. The low-grade manganiferous iron ores from the Cuyuna Range, in general, do not respond to conventional mineral dressing techniques because of their fine-grained texture. Reducing these ores to magnetite for subsequent magnetic separation and flotation has not given satisfactory results because concentrate grade and manganese recovery are often low. However, a technically feasible process appears to be metallization of the iron and concurrent reduction of manganese oxides to MnO with recovery of metallic iron by magnetic separation and extraction of manganese from the tailings by leaching. In 1962 the R-N Corp., with a grant from the Area Redevelopment Administration, conducted an amenability study of the metallization of manganiferous iron ore from the Cuyuna Range. The results of this preliminary investigation were sufficient to interest the Economic Development Administration in sponsoring further studies of the process with emphasis on secondary recovery of manganese from the nonmagnetic tailings. Inasmuch as the metallization process has considerable influence on the final form of the manganese - its texture and distribution between the magnetic concentrate and nonmagnetic tailings-the investigation included a study of metallization of the ore as well. Therefore, the investigation conducted at the Mines Experiment Station covered three interrelated phases: (1) laboratory R-N roasting studies and magnetic separation tests, (2) laboratory chemical extraction experiments of the nonmagnetic tailings, and (3) a mineralogical study of the crude ores and their various roast products. High-temperature x-ray diffraction investigation of the Fe-Mn-Si0,-0, system is the main topic of this paper and an extension of the mineralogical work. GENERAL GEOLOGY The Cuyuna Range is known for its complicated geologic structure, complex orebodies, and generally indifferent response to attempts at conventional beneficiation. Several geologists have made intensive studies of the Cuyuna Range, including Leithl (1907), ~darns&apos; (1910), Zapffe3 (1925), Grout and Wolff4 (1955), and schmidt5 (1963), whose study was the most comprehensive of all. The Range is covered with glacial deposits - till, out-wash, and lake sediments -up to 250 ft thick. Bedrock stratigraphic units of the Cuyuna Range consist of three tightly folded Precambrian sedimentary formations. The lower unit is the Mahnomen formation, composed of 2000 or more feet of argillite, slate, siltstone, and quartzite. The middle unit is the Trommald formation, which varies from 45 to 500 ft in thickness and comprises the major iron-bearing formation. The upper unit is the Rabbit Lake formation, consisting of over 2000 it of argillite, slate, and interbedded lenses of lean iron formation. In the central part of the Cuyuna Range, the units have been folded into a series of

Jan 1, 1969

By R. T. DeHoff, L. J. Buteau, J. Kronsbein

Network topology is introduced and used to describe sinter bodies at various stages of the sintering process. The matrices of incidence, loop-branch. tree-branch, and cut-branch are constructed and their relationship to the three-dimensional void space and the common two-dimensional bounding surface is established. The sintering body is assunzed to remain connected but this is not so with the void space. The topological invariants known as Betti numbers are related to this observed fact and provide parameters which measure the progress of the sintering process. They are extracted from the matrices by means of known algebraic operations. Experimental procedures are given which permit actual construction of the various matrices and determination of the Betti numbers by serial sectioning of the sinter bodies. A sinter body is produced by exposing a large number of metallic particles (0.00001 to 0.3 in. diam) to a temperature that is near but below their melting point. When these particles are maintained at such a temperature for a sufficient length of time, it is found that the interparticle contacts become welded. As time increases, these welds, often referred to as necks, grow. All of the space between the particles constitutes a single connected void; an ultimate consequence of sintering is the breaking up of the void into separated parts. A mathematical apparatus for describing the geometric characteristics of a sinter body at each stage of the process was first proposed by F. N. Rhinesl when he introduced the application of topology to this problem. He described the sinter body in terms of one of its topological invariants, the genus. The most important advantage of a topological description is invariance with respect to continuous deformations. This means that particle sizes and shapes need not be considered, resulting in considerable simplification and generalization of the geometric description. In the case of a sinter body, wherein the internal geometry is particularly complex, the simplification provided by topological concepts is absolutely essential. The important parameters in the Rhines model are the number of particles and the interparticle contacts. The invariant considered called genus is given by Euler&apos;s formula for the connectivity of two-dimensional surface of the sinter body. This surface includes the pore-solid interface. The Euler formula is G = C - P + 1 [1] where C = number of interparticle contacts, P = number of particles, and G = genus of the surface bounding the sinter body. In topology the term genus may be used to mean the number of self re-entrant cuts that can be made on a closed surface without dissecting it into more than one connected surface. Its use is restricted to the surface and does not apply to the three-dimensional volume enclosed or excluded by it. In the case of sintering, the volume enclosed by the surface is defined as the sinter body; the volume excluded will be referred to as the void space. There is an intrinsic reason for using genus as a characteristic number associated with a sinter body. The genus is related to the Gaussian curvature by the integral of the product of the principal curvatures taken over the entire surface of the sinter body, as given by

Jan 1, 1965

By Oliver Bowles

AMONG mining men as well as in the popular mind the conviction has held sway that mining is pre-eminently a western industry. True it is that gold, silver, copper and other metals have made the States of California, Colorado, Montana, Utah. Nevada and Arizona famous. The prominence attained by these States as mineral producers is, however, not measured alone by the money value of the products of their mines. While the metals are without doubt indispensable in industry, the glamour of the precious metals, and the lure of copper, lead and zinc have given to their ore deposits a sentimental interest that often quite out-weighs their commercial importance. Today a great group of more commonplace minerals are finding a place in commerce and industry rivaling that of the metals, but there is little sentiment attached to them, and,. therefore, they attain relatively little publicity. This is the great group of the non-metallic minerals, exclusive of fuels and oils, including stone, sand and gravel, cement, lime, gypsum, asbestos, mica, phos-phate rock and many others. Almost unnoticed they have grown in production to almost unbelievable pro-portions. The estimated value of metal production for 1925 is given as $1,380,000,000, of the non-metals (ex-cluding fuels) $1,294,000,000. The non-metallic industries are not new, many of them date back almost to pre-historic times; but, as the greatest of them (on a tonnage basis) provides raw materials for the construction industries, it required the activities of the present age of construction to bring about their enormous development. Many of them enter manufacturing as well as con-struction. Non-metallic minerals constitute the back-bone of our great chemical industries. While construction and manufacture reach to all parts of the country their widest development has been in the great industrial centers of the eastern Seaboard and the middle West. Consequently the raw materials of mineral origin required for these great industries have attained a remarkable growth in the eastern half of the- United States. In compiling figures of mineral production for 1924, for which more complete data are available than for later years, the surprising fact is brought to light that the non-metallic mineral produc-tion alone of some of the eastern and middle-western States exceeds by a substantial margin the total min-eral production of some of the western States that have been classed as essentially mining States. Thus the non-metallic mineral production, exclusive of coal and petroleum, of the State of Ohio, was approximately $150,000,000; of Pennsylvania $175,000,000; and of New York $107,000,000. For the same year, 1924, the total mineral production of Utah was $84,357,000; of Montana $70,632,000; of Colorado $61,488,000; and of Nevada only $26,226,000. Even Minnesota, with its enormous iron ore production, reached only $107,845,-000, or a sum about equivalent to the non-metallic min-eral production of the State of New York.

Jan 8, 1927

By J. M. McDowell

A study has been made to deter~r~irre how the behavior of a water drivee reservoir changes as a function of the permeability of the formation and as a function of the size of the aquifer. The effect of pressure maintenance programs on the rote of nat11rn1 water influx is also studied, (IS well as the influence on the influx of the position of water injection we1ls with reference to the oil-water contact. The results are determined by the use of an electrical reservoir analyzer and are plotted as families of curves of pressure, natural water influx, and water injection vs time or cumulalive production. Two size aquifers are studided. One is limited with a 36-inile radius, and the, other approximates an infinite reservoir. The field remains the same in all respects for the completed. study except that the permeability is changed to agree with that assumed for the aquifer. 1 N TR ODUCTI ON this study was undertaken in -dcr to determine how the pres- sure decline and water influx of a water drive field would change as a function of the rate of fluid withdrawals, as a function of the permeability of the formation, and as a function of the size of the aquifer. The effect of pressure maintenance programs on the rate of natural water influx was also studied as was the position of water injection wells with reference to the oil-water contact. The information has been determined by the use of an electrical reservoir analyzer1, sometimes referred to as a Carter type analyzer. This instrument is an analog type computer which can be set up to represent a water-drive oil field. It can reproduce the past performance of the field in terms of analogous electrical quantities when the proper circuit analog of resistors and condensers has been determined, also, it can determine the future behavior for any method of production which may be selected, or permit the comparison among several different methods. Although most applications of the reservoir analyzer"" have been to thc study of specific field performance, it is intended to use the analyzer here to help understand how various reservoir characteristics effect the final performance of the field and to sec under what conditions water injection will be of benefit and to what extent. Within the oil industry the performance of water-drive reservoirs was first described analytically by LV. Hurst&apos; and M. Muskat2 for certain types of boundary conditions. The solutions of the equations developed involved products of exponential functions and Bessel functions. Later publications by Hurst4 and van Ever-clingen" and the hooks of Muskat6 gave further information on reservoirs with other boundary conditions. They also presented rather extensive curves and tables to help evaluate the analytical expressions involved. A rccent series of publications by Chatas. bascd on the work of Hurst and van Everdingen, gives quite complete charts and tables of data to evaluate the pressure decline or water influx in infinite or limited radial reservoirs. and in linear reservoirs. The curves in all of these publications are given in dimensionless form

Jan 1, 1956

By K. D. Hester, A. W. Fletcher

A nickel-copper sulphide concentrate was treated in a pilot plant at Warren Spring Laboratory during 1961, by a hydrometallurgical roast-leach-solvent extraction process devised to cleanly separate the metal values and produce acid sulphate liquors containing the metals. It is shown that 86 pct of the nickel and 95 pct of the copper could be leached from the calcine, after a sulphatizing roast on finely ground flotation concentrate. Iron was removed from the leach liquor by limestone neutralization with a small loss of values. Copper and nickel were separated by solvent extraction with naphthenic acid in kerosene after partial neutralization of the iron-free liquors with ammonium hydroxide. Hydrogen sulphide and chlorine were used to remove zinc (and residual copper) and cobalt impurities respectively. The recovery of pure copper and pure nickel, by electrowinning, from the acidic solvent extract strip liquors finally produced, appears technically feasible. An economic analysis of production costs shows that small, geographically isolated, nickel-copper sulphide deposits cannot usually be worked profitably by established processes. The requirements for profitable operation on a comparatively small scale could possibly be met by a flotation-roast-leach process. Two difficulties, obtaining satisfactory extraction of nickel from a sulphide concentrate and separating the copper and nickel in solution, have prevented the previous use of this method. A solution to the first problem, dissolution of the nickel, was described in a recent paper by Thornhill.1 It was shown in this paper that copper and nickel in a flotation concentrate could be oxidized to water soluble sulphates by roasting in a fluidized bed with added salt cake. Workers at the Warren Spring Laboratory have shown that the separation of copper and nickel can be accomplished by solvent extraction using a relatively inexpensive carboxylic acid, naphthenic acid. Moreover, the mineral acid required to strip values from the loaded solvent could be produced, and the metals recovered, by electrowinning; thus the latter section of the process was regenerative. The removal of iron from the leach liquor and the elimination of impurities such as zinc and cobalt before nickel electrowinning would be necessary to complete the flowsheet. The process under investigation could therefore be summarized (Fig. 1) as follows: 1) Flotation to produce a bulk sulphide concentrate. 2) Fluidized bed roasting to sulphate the nickel and copper minerals. 3) Leaching of roaster calcine to extract soluble nickel and copper. 4) Precipitation of iron from the separated leach liquor by air oxidation after the adjustment of pH and temperature. 5) Recovery of copper from the iron-free Liquor by pH adjustment and liquid-liquid extraction. 6) Purification of the copper raffinate by removing zinc and residual copper as insoluble sulphides and cobalt as cobaltic hydroxide. 7) Recovery of nickel from the purified liquor by pH adjustment and liquid-liquid extraction. Laboratory and pilot plant studies detailed below, were carried out at the Warren Spring Laboratory, to test the feasibility of each one of the unit processes and to obtain preliminary plant design data. FLOTATION The ore was an altered basic rock containing concentrations of magmatic sulphides.

Jan 1, 1964

By E. H. Rennhack

Phase equilibria of the zinc-rich portion of the Zn-Fe-A1 system containing up to 20.0 wt pct Fe and Al have been investigated at 600°C (1112°F), 450°C (842°F), and room temperature by metallographic and X-ray diffraction techniques. The phase relationships were found to involve only those phases present in the three binary systems. THE presence of small quantities of aluminum (approx. 0.2 wt pct*) in zinc galvanizing baths is known to suppress the formation of Zn-Fe alloy layers within the coating.&apos; As part of an extended investigation of this suppression effect and the alloy reactions involved, the zinc-rich corner of the Zn-Fe-A1 equilibrium system containing up to 20.0 pct Fe and Al was determined at 600°C (1112°F), 450° F (842° F), and room temperature. The present paper reports the findings of this study. The constitution of the Zn-Fe system has been reported by Raynor2 based mainly on the work of Schramm3-3 and Truesdale et a1.6 The solid solubility of iron in zinc is extremely small and lies between 0.0009 and 0.0028 pct in the range 150° to 400°C (302°to752°F). Within the temperature and composition range of interest, a eutectic reaction involving nearly pure zinc, liquid = Zn+FeZn13, is observed at about 419°C (786° F) and 0.018 pct Fe along with a peritectic reaction, FeZn7+ liquid e FeZn13, at 530°C (986° F) and 6.2 pct Fe. The latter reaction is sluggish due to the large proportipn of solid phase involved in the transformation. Halla et al.,7 identified the compound FeZn13 as monoclinic with a = 13.68, b = 7.63, c = 5.07, and B = 128°44&apos;. The structure of FeZn7 was reported by Bablik, et al.,8 to be of hexagonal symmetry, belonging to either the C6v = C6/m mc or D46h = C6/mc space group. Divensions of the unit cell are a = 12.81A and c = 57.6a. The Zn-A1 diagram as composed by Raynor9 and later Gebhardt10 is characterized by a eutectic decomposition, liquid 382°C (720°F) and 95.0 pct Zn and a eutectoid decomposition, at 275° (527°F) and 78.0 pct Zn. The eutectoid reaction cannot be suppressed permanently by quenching. Above 275° (527° F), a and a&apos; co-exist in a closed miscibility gap between 31.6 and 78.0 pct Zn. Both phases are fcc and have nearly the same lattice parameter. The maximum solubility of aluminum in zinc (B) is approximately 1.0 pct at the eutectic temperature. PROCEDURE Materials. The experimental alloys were prepared from both massive and powdered material. Cast alloys were composed from three zinc-base master alloys containing 8.0 pct Fe, 16.0 pct Fe, and 50.0 pct Al which were made from C.P. zinc, Armco iron, and

Jan 1, 1962

By A. P. Woods, J. A. Elias, A. J. Heckler

A method is described by whichX-ray pole figures and axis density figures may be plotted automatically. The X-ray data are obtained using a Siemens texture gonionleter and the Schulz reflection method. Composite sampling methods are used to obtain a full quadrant of the pole figure. The contour lines of the pole figure and axis density figures are drawn using a computer-controlled x-y plotter. The computer program used to draw the contours was obtained from ZBM. POLE figures used to describe crystallographic orientations of poly crystalline sheet materials are usually plotted manually from X-ray diffraction output in the form of a strip chart recording of the intensity distribution of a given crystallographic pole in physical space. Today&apos;s computers and associated plotting equipment now make it possible to plot pole figures and axis density figures automatically. Inverse pole figures have been determined by mathematically "inverting" X-ray pole figure data.&apos;-&apos; In general, these methods require complicated, time-consuming numerical calculations. A more economical but less accurate method is to determine the axis densities of low-index crystallographic poles using an X-ray diffractometer. When these axis densities are plotted in a unit stereographic triangle contour lines can be drawn to represent the axis density distribution. This can now be done automatically. Computers were used to plot pole figures by a method developed by Holland, Engler, and powers.&apos; In their method intensity ratios based on a random standard sample were obtained from a strip chart recording, and the stereographic (x, y) coordinates of these ratios were determined by a computer. Symbols characteristic of different intensity ratio levels were then plotted using an automatic x, y plotter and intensity contours were drawn manually. The present paper describes a method by which pole figures and axis density figures have been automatically plotted from digital data obtained from a Siemens X-ray unit. Plotting was accomplished using an IBM 1620 computer and a Calcomp 563 digital plotter. COMPUTER PROGRAM The computer program was obtained from IBM Systems Reference Library, No. 1620-CS-05X, and was designed to plot contour maps from randomly distributed data. It consists of a set of twelve separate subprograms, four of which were used in this work. The program takes a given distribution of data points and by a numerical method determines the values at mesh points of a square grid system superimposed over the input data. The output data from this program is in a form suitable for input to the contour plotting program. A smoothing program is also available which calculates new mesh point values from a continuous function fitted to neighboring mesh points. The degree of smoothing depends on the number of points around a given grid point which are used to adjust or smooth the grid value. The contour plotting program is designed to allow the user to specify the interval, scale, and annotation of the contours to be plotted. EXPERIMENTAL PROCEDURE Pole Figure Data Points. Diffracted X-ray intensities were determined using a Siemens texture goniometer and the schulzs reflection method. Due to geometric

Jan 1, 1968

By Charles C. Fatino, Joel S. Hirschhorn

Loose compacts of strained and annealed stainless-steel powders were sintered at various temperatures and times to determine the effect of residual strains on the sintering behavior. The atomized powders were prepared by annealing, ball milling, and rean-nealing. The residual strains and domain size were determined by a Fourier analysis of X-ray diffvaction dala. The specimens were prepared by siwzultaneously sintering cylinders of both strained and unstrained powder. The evaluation of the sintered compacts included density measurements, metallographic examinations, and analyses of X- ray diffraction data. The results of these studies reveal a definite increase in sintered density and sintering rate for the strained powders. THE pressure compacting of metal powders causes deformation of the particles, mechanical interlocking, and increased contact area. After the deformation, severe residual strains remain in these particles. The subsequent contributions of these strains to the sintering process have been considered to be negligible, since the recovery and recrystallization temperatures usually occur prior to the temperature required for the sintering process. Sintering is con-sidered to be the process by which the powders are transformed into solid compacts at temperatures below their melting points. The sintering operation for stainless steel usually takes place in the range of 2050" to 2400°F (0.84 to 0.95 T,, where T, is the absolute melting point or liquidus temperature) while the temperature required for recovery is approximately 1800°F (0.75 T,). However, it has been shown for several metal powders that densification becomes significant in the range of 0.35 to 0.45 T,.&apos; It is the purpose of this study to determine what effect residual strains have upon the sintering behavior of stainless-steel compacts. Loose compacts were selected for study in order to isolate the strain contributions and eliminate the variables inherent in sintering of pressure-formed compacts. Additional variables were minimized by using only one mesh size, one composition, one particle shape, and also by simultaneously sintering both types of powder. Very little work has been carried out previous to the present study to delineate the effect of strains on sintering behavior. Lenel et 01.2 observed that residual stresses in copper compacts caused shrinkage at comparatively low temperatures. Delisle3 loose-sintered ball-milled electrolytic iron and observed that bonding among particles began at a lower temperature as compared to the behavior of annealed powder. Increased densification of ball-milled oxide powders has also been noted.4&apos;5 EXPERIMENTAL PROCEDURES Powder Preparation. The powder used for this study was a commercial-type 316L stainless steel made by the atomization process. A typical chemical analysis is: C- 0.025 pct Mo- 2.2 pct Cr-18.6 pct Ni-12.5 pct Fe—Balance The atomizing process is essentially the rapid freezing of liquid droplets. This nonequilibrium cooling causes coring to occur and two distinct phases are present within the solid particle, the austenitic phase and the ferritic phase. Due to the presence of this ferritic phase, the particles tended to fracture as well as become cold-worked during the subsequent ball-milling operation. (It was also found that this type of cooling produced a broadened and shifted

Jan 1, 1968

By H. H. Johnson, Eric W. Johnson

A newly developed ac technique was used to measure the electrical-resistivity changes associated with both cyclic stressing and subsequent annealing of high-purity and OFHC copper. The early stage of push-pull fatigue was explored at 293° and 4.2°K, with stresses chosen for an expected fatigue life of 2 to 8 X 105 cycles. For high-purity copper, fatigue at 293°K was accompanied by an initial increase in resistivity. After about 5000 stress cycles, no further increase was observed. Annealing studies showed that the resisticity increment could be accounted for solely in terms of an increased dislocation density, to about 2 x 1010 disl pev sq cm. Fov 42°K fatigue, however, the resistivity increased continually, with no evidence of saturation, as approximately (No. of stress cycles)1/4. This is intevpreted to result from both dislocation multiplication and vacancy production; estimated vacancy concentrations are 10-4 to 10-9. The continuous resistivity increase was inhibited by interspersed annealing treatments at 293°K, which also raised the level of the stress-strain curve. These effects are attributed to annealing of vacancies into dislocation loops. In contrast, OFHC copper fatigued at 4.2°K showed saturation of electrical vesistivity after only a few hundred cycles, and it appeared that vacancies annealed out completely between 77° and 293°K. MaNY observations suggest that both dislocation multiplication and point-defect production are important aspects of fatigue deformation. An increase in dislocation density with number of stress cycles has been demonstrated or implied by several experimental techniques, including optical metallography with lithium fluoride,&apos; electron microscopy with copper,2 thermal conductivity of Cu-Zn alloys,3 and peak-stress measurements during cycling at constant plastic strain amplitude.4,5 At low amplitudes and/or stresses saturation of fatigue hardening and dislocation density occurs early in the expected fatigue life,4-6 frequently by a few hundred cycles. The evidence for point-defect production is somewhat less extensive, but it is nonetheless persuasive. Rosenberg7 reported briefly that, for equal stresses, copper fatigued at liquid-hydrogen temperature displays an increase in electrical resistance some ten times that which accompanies unidirectional stressing. Further, the extra resistance saturates after a few hundred stress cycles, and does not anneal significantly until a temperature of about 170°K is attained.&apos; Point-defect production during fatigue is also suggested by 1) the softening during cyclic stressing of initially strain-hardened polycrystal-line copper9, 2) the strong temperature dependence of the yield strength of fatigue-hardened mono- and polycrystalline copper,579"0 and 3) the influence of intermediate annealing upon slip-band formation in copper fatigued at 90°K.8 It is evident that characterization of the fatigued state requires a knowledge of both point-defect and dislocation densities. For this purpose electrical-resistivity measurements are useful, but they are difficult to perform because of geometric limitations. Push-pull fatigue is necessary to obtain a macroscopic ally uniform deformation over the specimen cross section; however, the specimen must then have a low slenderness ratio to avoid plastic buckling, while the standard dc resistivity technique requires a very slender specimen for

Jan 1, 1965

By AIME AIME

The name and address of the school are given first, followed by the length of the regular undergraduate curriculum, the degree granted, types of courses giben, and the name of the man in charge. This covers only work for the first or Bachelor degree in each case. The following abbreviations are used: B. Bachelor Cer. Ceramic. E. Engineer or Engineering Eng. Engineering or Engineer Geol. Geologist, Geological, or Geology M. Mines or Mining Met. Metallurgy or Metallurgical Mng. Mining Pet. Petroleum Ref. Refining S. Science Tech. Technology or Technical

Jan 1, 1939