Search Documents

By Richard H. Sprute, Dennis J. Kelsh

Slow-settling, fine-grained suspensions can often be dewatered and densified by applying direct current between buried electrodes. Although water removal rates and power expenditures depend on physical and chemical properties of the treated slurries, metal mine tailings from Idaho, Colorado, and Mexico have responded well in laboratory testing, as have 29 samples of ultrafine coal waste from mines in nine states. This Bureau of Mines report reviews field tests at two Idaho metal mines and describes the recent installation at the Henderson molybdenum mine near Empire, Colorado, and the treatment of coal sludge at a Clinchfield Coal Co. preparation plant near Dante, Virginia.

Jan 1, 1980

By R. C. Croft

Many chemical methods of upgrading ilmenite to enhance its titanium dioxide content involve reduction of the FeO in this mineral followed by solution of the metallic iron produced. While the use of most mineral acids for this purpose entails acid regeneration or salt disposal problems, these difficulties can be overcome with carbonic acid. Satisfactory rates of iron removal have been achieved at temperatures below 100° C and at CO, pressures up to 600 psi. Lowering of gas pressure over soluble bicarbonate solutions permits recovery of CO. and precipitation of iron oxide. The removal of the manganese, often present in ilmenites, is also feasible with these treatments.

Jan 1, 1972

By F. S. McNicholas

IN the first big blast at Climax, a "loop back" (three-wire system) was used (Fig. I), with the idea of securing a wiring system that would give to all series the same amount of current. Single-phase, 60-cycle, 13,800-volt [ ] power was furnished to the blasting transformers, each of which has a rated capacity of 600 amp. at 480 volts. Two blasting leads were taken from these transformers, giving a blasting current of single phase, 60 cycle, 480 volts, with an instantaneous capacity of more than 600 amp. The blasting switch was on the secondary leads from the transformers, to avoid lag in energizing them.

Jan 1, 1938

By Paul B. Barton

Unconventional mineral deposits are those that differ significantly from productive deposits in mineralogy, grade, or geologic setting. Thus, the initial representatives of each deposit type are, by definition, “unconventional” until they are exploited. The “unconventional” status changes to "conventional" because of economic shifts (e.g., bulk silver ores), because of technological innovations (e.g., froth flotation), or simply through the recognition of, and production from, novel mineral concentrations. Heretofore the discovery of new deposit types has been almost entirely accidental, but the long- established concept of the geochemical cycle provides a nearly untouched opportunity and challenge for the application of geochemistry in predicting novel, potentially economic, mineral concentrations.

Jan 1, 1983

By G. M. Ritcey

The concentration of metals in the solution, the .value of the metal being recovered, together with the flow through- put, may singly or in combination conbribute to the decision on the possible use of solvent extraction. Also, as noted earlier, the upstream and downstream aspects of the overall process have to be considered. The economic considerations may be divided into: 1. Capital investments 2. Operating costs Capital Cost The capital costs can be influenced by the following: 1. number of stages; 2. kinetics; 3. coalescence; 4. entrainment; 5. flow rates and ratios; 6. building requirements; 7. ancillary equipment; 8. environment constraints or requirements; 9. engineering design.

Jan 1, 1978

By M. S. Enders, L. M. Rogers

The Little Rocky Mountains host epithermal gold-silver bearing vein and stockwork deposits in a syenite intrusive complex. Pegasus Gold Ltd. is currently mining these oxidized deposits by open-pit methods and recovering gold and silver by heap-leach processes. A geologic program has been designed to effectively determine the basic ore characteristics; 1) mineralization; 2) oxidation; 3) structural setting; 4) lithology; 5) alteration; and ultimately, 6) the leachability of the ore. Geologic mapping, sampling, drilling, assaying, and testing are routinely used in exploration, development, production control, mine planning, and ore reserve estimations. Timely and accurate assay results are essential for the program's success.

Jan 1, 1984

By R. M. Porter

The Sullivan mine of Consolidated Mining and Smelting Co. of Canada Ltd. is located one mile west of Kimberley. With its daily production of 10,000 tons, the mine is the largest in British Columbia and one of the outstanding mines of the world. The Sullivan orebody dips from nearly horizontal to 45". The ore zone is a bedded replacement de- posit in argillite with a width varying from a few inches up to 300 ft. The main sulfide minerals are pyrrhotite, pyrite, galena, and sphalerite. The chief metals produced are lead and zinc, with less important qualities of iron, silver, tin, antimony, bismuth, cadmium, indium and sulfur.

Jan 12, 1963

By H. M. Varner

Under sponsorship of the US Bureau of Mines and the Department of Energy, a new type of rotary rock drill was developed by The Bendix Corp. Originally developed for the production of holes for the installation of longer than seam height roof bolts, the flexible drill is a useful tool for many drilling applications. It allows hands-off or remote production of holes for increased drilling speed and greater operator safety in any strata suitable for rotary drilling. This paper discusses various applications and experience for the flexible drill system in coal, metal/nonmetal mining, and for civil engineering uses. Manual, remote control, and automatic roof bolter modules are also discussed.

Jan 1, 1984

By Craig R. Smith, Warren Pfefferle

Tests were conducted utilizing large flat jack devices placed in a vertical slot for high pressure loading of rock to measure in-situ properties of a rock mass. The high pressure flat jack devices were used as a site investigation tool to obtain rock mass properties. Tests were conducted before and after a 100 ton surface high explosive detonation test to assess explosive effects on the rock. It was conclusively demonstrated by these tests that meaningful flat jack tests could be successfully accomplished; also, a significantly different response of the rock medium was measured as larger areas of rock were loaded. Surface jointing was severely disturbed by the explosion.

Jan 1, 1971

By J. D. Forrester, Erich Sarapuu, T. C. Cheasley

RANKING high in the nation's wealth of natural resources, readily available liquid and gaseous hydrocarbons are nevertheless falling steadily in supply, while industrial requirements for hydro- carbon compounds are greater today than during the peak period of World War II. Theoretically, several processes will increase the future supply of liquid and gaseous fuels, but the practical application of these methods depends on two controlling factors: 1-that enough carbon- bearing material be available to warrant industrial exploitation, and 2-that the given process be physically, chemically, and economically applicable. With regard to the first factor, the Western Hemisphere is fortunately well supplied, see Table I.

Jan 9, 1954

By D. E. Swets, P. C. Frank, D. L. Fry

THE hydrogen-steel system has received considerable attention in the past several years. Recent experiments in this laboratory have shown that another group of operations, namely, sanding and grinding,' must be added to the already well-estab- lished list of phenomena that cause hydrogen to permeate steel. Qualitative tests which have been made with a very sensitive ion-gage type of detector similar to that used by Norton,' showed that sanding a steel surface caused hydrogen permeation. A metal type 6~6 vacuum tube was used as the ion gage with an electrometer to measure the ion c~rrent.~ The protective enamel coating was removed from the tube.

Jan 1, 1959

By S. L. Tainter

This paper describes the nature of engineering and geologic services for the production stage and a review of pit design factors peculiar to the development period. The Mission pit has passed into the mining phase where development is of secondary importance; however: until the pit reaches its final size, development will be a continuing function occurring simultaneously with mining operations. The deposit occurs in an extensive zone of altered sedimentary rocks which have been fractured by three fault systems, flexed or folded, and intruded by monzonite porphyry. The deposit is a low-grade copper sulfide "porphyry" type orebody within a broad zone of pervasive hydrothermal alteration in sedimentary rocks.

Jan 12, 1965

By K. Stout, L. Friel

Some rock mechanics theorists believe that if a hydraulically placed backfill can be introduced in a stoped out area, which will minimize wall closure by taking high stresses across the fill with minimum compaction, then heavy ground and rock burst phenomena will be minimized. The paper will discuss a large scale laboratory project when fill strength was increased over four times by the head vibrated method and up to well over 20 times by the double placed, cemented, vibrated head method when compared to conventionally placed fills. The only preconditioning of the 60% solids by weight slurry was the addition of cement in some tests.

Jan 1, 1983

By F. S. McNicholas

In the first big blast at Climax, a "loop back" (three-wire system) was used (Fig, I), with the idea of securing a wiring system that would give to all series the same amount of current. Single-phase, 60-cycle, 13,800-volt power was furnished to the blasting transformers, each of which has a rated capacity of 600 amp. at 480 volts. Two blasting leads were taken from these transformers, giving a blasting current of single phase, 60 cycle, 480 volts, with an instantaneous capacity of more than 600 amp. The blasting switch was on the secondary leads from the transformers, to avoid lag in energizing them.

Jan 1, 1940

By P. A. Young

The historical background of on-strand cooling is given, together with a resume of recent practical developments. Laboratory test procedures are then considered in detail, for both productivity and quality parameters, with particular reference to the design of the Ravenscraig No 3 machine (Scotland). A heat transfer model is presented for a porous sinter with propagating cracks. The influence of cooling/sintering area ratio, sinter strength, granulometry, return fines, coke consumption and FeO levels are examined in relation to economics. A detailed comparison of capital and running costs for two different strands, designed for identical duties, but with off or on-strand cooling, is then given.

Jan 1, 1977

By Thomas P. Oxford, Leslie G. Bromwell

The waste clay slurry produced during beneficiation of Florida phosphate ore presents a major environmental problem. The large volume of waste requires impoundment in above-ground disposal areas surrounded by earthen dams. As the result of a comprehensive research effort, three approaches to improving clay dewatering involving admixing of sand tailings have been developed. These provide satisfactory performance and appear to be compatible with the technological and economic constraints of the industry. Means of determining waste clay characteristics and analyzing mining waste disposal situations by computer simulation have been devised in support of the planning and field testing effort. Detailed examples demonstrating the applicability of the computer programs are presented.

Jan 1, 1980

By F. S. McNicholas

In the first big blast at Climax, a "loop back" (three-wire system) was used (Fig, I), with the idea of securing a wiring system that would give to all series the same amount of current. Single-phase, 60-cycle, 13,800-volt power was furnished to the blasting transformers, each of which has a rated capacity of 600 amp. at 480 volts. Two blasting leads were taken from these transformers, giving a blasting current of single phase, 60 cycle, 480 volts, with an instantaneous capacity of more than 600 amp. The blasting switch was on the secondary leads from the transformers, to avoid lag in energizing them.

Jan 1, 1940

By F. W. Gibson

A detailed description of the smelting and refining operations of the Amax-Homestake Lead Toller's smelter at Buick, Missouri. This is one of two completely new lead smelting and refining operations to go into operation in the United States in over forty years. Incorporated into the operation are the new methods and equipment which have been developed and lend themselves to the particular metallurgy of this plant. The text, as well as the statistical data presented, represent actual current practice after 22 months of operation, and although the metallurgy is considered to be relatively simple, several metallurgical problems unique to Missouri concentrates are discussed.

Jan 1, 1970

By C. E. Corson

The experiments of which the results and significance are set forth in this paper do not by any means cover the whole subject of the heat-treatment of the material referred to, yet they constitute a contribution to that general subject, rather than to the special department of' annealing. The material here considered is acid open-hearth steel, containing from 0.50 to 0.80 per cent. of carbon, with a nearly uniform percentage of other elements. This class of steel is rapidly increasing in commercial importance. It is even rumored that the rail-specifications of some railroads will hereafter require open-hearth steel. Yet this particular grade seems to

Jan 1, 1907

By P. W. Neurath

IN recent years the domain theory of ferromag-netism has been put on a sound experimental and theoretical basis. But its application to one of the most widely used high quality magnetic materials, the cold-rolled grain-oriented 3 pct Si-Fe used in transformer cores, has been rather difficult because of the complexity of the domain structure of the poly crystalline sheet material. This paper presents some experimental data for this material, showing the relation between plastic and elastic stresses, 60-cycle watt losses, and the domain structure as observed visually. Only a very tentative qualitative explanation of the effects will be attempted. Some initial results were reported earlier.'

Jan 1, 1957