Search Documents

By H. K. Birnbaum, H. B. Aaron

he authors suggest that a number of the types of yield phenomena which have been observed in high-purity fcc metals are due to dislocation interactions bccurring at the surface of the crystals rather than due to volume effects. Since rather different inter-pretationS2,7,12,14,15,21-23 of these effects have been suggested, it is of some importance to ascertain the role of the surface in these yield phenomena. It should be first noted that the high-purity fcc metals appear to exhibit several distinct types of yield phenomena. The "unloading yield point" which is observed on reloading the specimen after removing the applied load has been found to be independent of the time of holding in the unloaded condition. If however the specimen is aged while under load and re-tested without removing the load, a yield point is observed which does depend on the aging time and tem-perature. Feng and Kramer suggest that the removal of the unloading yield point on removing sufficient material from the surface of the specimen indicates that the effect is associated with dislocation interactions at the specimen surface. Their observations are counter to those of Haasen and Kelly5 and Birnbaum.12 Since the unloading yield points are extremely small (-2 pct of the flow stress) the results of the surface removal will depend on whether the material is removed uniformly over the gage length. The introduction of small etch pits or the removal of more material from one portion of the specimen than from another will result in preferential yielding and obliteration of the yield point. With the normal electropolishing techniques it would be difficult to avoid these effects. The data obtained by Aaron and Birnbaum, Fig. 10, on aluminum polycrystalline specimens indicate that, although the unloading yield point and the strain-aging yield point are not simply additive, a time- and temperature-dependent yield point is observed under conditions where no creep is observed. This does not agree with the results of Feng and Kramer but does agree with the results on copper15 and gold.7~23 The source of the discrepancy may be the procedure used by Feng and Kramer to correct their time-dependent yield points for the effect of creep. Since the strain-aging yield point is not independent of the pre-aging strain rate, Fig. 11, the effects of creep cannot

Jan 1, 1967

By R. E. Hathaway

INTRODUCTION For a number of reasons, the mineral processing industry has been slow to adopt significant automation of its processes. Most ore grinding operations can be operated manually so the pressure for automation to run the process has not been there. Furthermore, many plants had proven over years of operation that manual operation would produce a profit, so why automate? Until recently, the instrumentation necessary for automation of the grinding process was not available. All this has now changed, however. Increasing costs for labor, fuel, power, grinding media, reagants, and capital equipment have not been matched by the market price of the finished product. This cost-price squeeze has made it mandatory to reduce operating costs and improve the efficiency of the process to remain profitable. A number of other factors have added to the direct operating cost to make the problem even worse. These include environmental pressures to conserve natural resources and reduce smelter stack emissions; increased competition--especially from developing countries, varying economic conditions, stockpiling, governmental controls, and to top it all off, lower grade ore bodies. Although many of these other influences are good overall, they take their toll in cost per ton of delivered product. Fortunately, many operators are finding the solution to the cost-price squeeze in instrumentation and process control. Automated processes yield tighter spec. products, require less operating labor, produce more product from a given plant, and reduce unit cost by increasing process efficiency. The plant manager has a "handle" on the plant through process control so that he can change operating modes as economics dictate by changing the set point of some process controllers. He can even respond to economic conditions by switching control strategies from one that maximizes production to one that maximizes recovery, or minimizes unit cost, etc. This has all been made possible by the advent of on-line analytical instruments and practical process control computers. On-stream particle size (1), x-ray, and silica analyzers are now available and in use in many plants. Digital computer hardware and software has become practical so operators can use it without trying to become computer experts. This chapter describes the approach toward design and implementation of automatic grinding circuit control that has proven to be the most cost effective, based upon results from a number of

Jan 1, 1982

By David J. Mack

A survey and critical appraisal of published information about Young's modulus was originally made by the writer because of a complete lack of information about this very important quantity in works on. mechanics, physical metallurgy, physics, and other sciences. It was felt that a comprehensive summary of such information about Young's modulus might be of general interest and may suggest new problems or lines of attack on other problems that involve E. Hence this paper has been prepared even though it is only a review, with no new ideas or experimental data. The references are only those used in assembling the paper. No attempt was made to compile a complete bibliography on the subject of Young's modulus. CalculatioX oP YouNg's Modulus from Theoretical or Empirical CoNsidera-tions Many attempts have been made to compute E from theoretical considerations. The earliest calculations were probably those of Tomlenson (1883) and Souther-land (1891), but Fess'enden4',~ made extensive calculations a few years later and arrived at the relationship: £ = 78.TOw(i)* where V is the atomic volume. In 1923, Peczalski, working from the same standpoint but with more information available on atomic structure, arrived at an identical relationship, which he expressed as: where B is a constant of value about 8 . 107, p is density and mis atomic weight; the atomic volume, of course, being ml p. Portevind4 immediately pointcd out that while the equations of Fessenden and Peczalski were true of the common metals, they gave low values for the refractory metals with high moduli (Fig. I). He showed (Fig. 2) that much better concordance was obtained by means of an empirical equation of the form: F- KT" where K is a constant; T the absolute melting point; V, atomic volume, and a and b constants of value approximately I and 2 respectively. This constant K in the Portevin equation is not necessarily the same for all elements, as shown by Thompson. Other equations for E based upon theoretical considerations have been derived by Honda and Yamada49 and Lasareff.50 The most recent calculations of elastic moduli based upon quantum mechanics are probably those of Fuchs He extended the method of Wigner and Seitz for calculating the lattice energy and compressibility of monovalent metals and computed the elastic constants of lithium, 18

Jan 1, 1946

By F. N. Rhines

Sintering may be defined as the process by which powders bond themselves into coherent bodies, usually, although not necessarily, under the influence of pressure and elevated temperature. For the sake of clarity and simplicity, the present survey will exclude from consideration the sintering of mixed or alloyed powders, with attendant complications, but at the risk of overlooking information of general applicability. Sintering in the presence of a liquid phase is thus automatically eliminated. The sintering of alloys involves much additional subject matter and deserves separate consideration. Since the literature of the subject is extensive and widely scattered, it will not be feasible to consider the contributions individually. Instead, the subject matter will be classified according to experimental observations and theory, and will be presented in summary form. It should be noted that the appended list of references does not constitute a complete bibliography; it includes only those works quoted below. More extensive bibliographies are included in several of the references; see particularly references 7, 9, 28, 34, 38, 50, 52, 54, a "Bibliography on Powder Metallurgy" published by the Library of Congress and a pamphlet published by the Metals Disintegrating Co. entitled "The Field of Powder Metallurgy and Bibliography." 11. Summary of Experimental Observations The following classified list is composed of general statements of established fact derived from the experimental results reported in the published literature. A few contested observations are included, because of their potential importance; these are labeled as such. Any satisfactory and complete theory must be capable of explaining all of the uncontested facts. Obviously, some important facts may be missing from this list and these may hold the key to the correct explanation of the sintering process, but the possible lack of such material should not deter attempts to understand the subject on the basis of what is available here. A, The Initial Bond at Room Temperature a. To a limited extent uncompressed powders and massive metals adhere at room temperature. Clean tin powder forms a weak "cake" on standing at room temperature, the strength increasing with time. Clean gold surfaces adhere on light con-tact, as do those of many other substances, including nickel.27 b. Upon compression the strength of the bond- is increased progres-ivelv. There is a limit of pressure

Jan 1, 1946

By J. A. Ede

The object of the writer is to call attention to a rather unique aggregation of economic products distributed over a line of succeeding formations about 3 mi. long, to be seen within a few miles of La Salle, Ill. Fig. 1 is an ideal section of the stratification exposed and exploited along a distance of 3 1/5 mi. in a southwesterly direction from the quarry of the Utica Hydraulic Cement Co. located near the historic site of Kaskaskia village to the Oglesby shaft at Oglesby. No attempt has been made to cover the whole field, special mention only being made (with the exception of two places) of the operations found along the course or parallel to the direction assumed in the ideal section. I have used Fig. 2, after J. R. Bent and De Witt Kelly, to locate the relation of the La Salle anticline to the coal mines of this district and to show the operation of No. 1 and 3 mincs of the Illinois Zinc Co. Anticline and the Rock Formations Owing to the structural deformation between La Salle and Utica, the older rocks of the state are exposed to the surface along the northern embankment and the bottoms of the Illinois River valley near the latter place. At; the Illinois Zinc Co. works, Sec. 16, Tp. 33, R 1, a well for water mas sunk 1828 ft. and samples taken every 10 ft. of the ground penetrated; duplicates were sent to Mr. Cady of the Illinois Geological Survey. A general compilation or synopsis study of this section is here presented. As the well is over 1 mi. west of the Western limb of the anticline, the section affords some reliable data. These samples were studied and interpreted by H. M. DuBois as Lower Magnesian, and by G. H. Cady as the Lower Magnesian. The results are given in Fig. 3. The most interesting geological feature of this district is the La Salle anticline. In 1865, Leo les Quereux, looking at Split Rock, asked how it happened that the upper coal measures overlie strata of the Lower Silurian and what has become of the formations which are generally found intermediate—the Upper Silurian, the Devonian and sub-carboniferous, and the lower member of the coal measures?

Jan 1, 1920

By A. H. Shoemaker

THE shutdown of Homestake by Government order L-208, with its consequent disruption of a very stable and trained working force, coupled with postwar inflation and the coincidence that a mining depth had been reached that posed problems of ventilation, access to exploration areas, and choice of mining methods that would be applicable to zones of greater rock pressures made a very searching analysis of every phase of Homestake's operations a necessity. Any changes to be made had not only to meet the problems of deeper mining but also had to provide greater efficiency so that the mine might operate at a substantial profit until such time as a gold price adjustment might be forthcoming that would offset post-1945 inflation. Geology and Mining Situation The Homestake mine lies in the northern Black Hills in an area of Pre-Cambrian rocks exposed by the erosion of the paleozoic formations which covered the Black Hills. The Pre-Cambrian rocks in the vicinity of Lead comprise metamorphosed sediments with a total thickness of about 20,000 ft. The oldest formation, the Poorman, is ankeritic carbonate schist. The next oldest, the Homestake formation, host rock for all Homestake orebodies, is a siliceous iron-magnesium carbonate schist. The younger formations are dom-inantly argillaceous with some quartzites. Tertiary intrusive rocks cut all formations. The Pre-Cambrian rocks have undergone extreme isoclinal folding. Superimposed on this intricate folding are zones of shear folding which cross the isoclinal folds at small angles. The Homestake orebodies are pipelike replacements of the Pre-Cambrian Homestake formation where certain cross folds intersect some earlier isoclinal folds. These orebodies plunge flatly to the southeast at variable angles locally as steep as 45". The orebodies are replacement areas where numerous vein quartz of irregular shape have formed with surrounding zones of chlorite alterations containing disseminated sulfides and metallic gold. Where the numerous individual quartz veins with the sulfide and gold-bearing alteration zones are close together, large irregular orebodies with a roughly elliptical plan outline result. These ore zones may be more than 200 ft wide and 700 ft long in plan area. They have followed down the plunge of certain severely folded structures with great persistence. Two vertical operating shafts, the Ross and Yates, serve the mine, one with rope capacity to reach the 4850 level, the other to the 5000 level.

Jan 1, 1959

By F. N. Rhines

I. An Outline of the Theory of the Sintering of Pure Metal Powders SINTERING may be defined as the process by which powders bond themselves into coherent bodies, usually, although not necessarily, under the influence of pressure and elevated temperature. For the sake of clarity and simplicity, the present survey will exclude from consideration the sintering of mixed or alloyed powders, with attendant complications, but at the risk of overlooking information of general applicability. Sintering in the presence of a liquid phase is thus automatically eliminated. The sintering of alloys involves much additional subject matter and deserves separate consideration. Since the literature of the subject is extensive and widely scattered, it will not be feasible to consider the contributions individually. Instead, the subject matter will be classified according to experimental observations and theory, and will be presented in summary form. It should be noted that the appended list of references does not constitute a complete bibliography; it includes only those works quoted below. More extensive bibliographies are included in several of the references; see particularly references 7, q, 28, 34, 38, 50, 52, 54 a "Bibliography on Powder Metallurgy" published by the Library of Congress and a pamphlet published by the Metals Disintegrating Co. entitled "The Field of Powder Metallurgy and Bibliography." II. Summary of Experimental Observations The following classified list is composed of general statements of established fact derived from the experimental results reported in the published literature. A few contested observations are included, because of their potential importance; these are labeled as such. Any satisfactory and complete theory must be capable of explaining all of the uncontested facts. Obviously, some important facts may be missing from this list and these may hold the key to the correct explanation of the sintering process, but the possible lack of such material should not deter attempts to understand the subject on the basis of what is available here. A. The Initial Bond at Room Temperature a. To a limited extent uncompressed powders and massive metals adhere at room temperature.28 Clean tin powder forms a weak "cake" on standing at room temperature, the strength increasing with time. Clean gold surfaces adhere on light contact,"' as do those of many other substances, including nickel." b. Upon compression the strength of the bond is increased progressively.28 There is a limit of pressure

Jan 1, 1946

By F. N. Rhines

Sintering may be defined as the process by which powders bond themselves into coherent bodies, usually, although not necessarily, under the influence of pressure and elevated temperature. For the sake of clarity and simplicity, the present survey will exclude from consideration the sintering of mixed or alloyed powders, with attendant complications, but at the risk of overlooking information of general applicability. Sintering in the presence of a liquid phase is thus automatically eliminated. The sintering of alloys involves much additional subject matter and deserves separate consideration. Since the literature of the subject is extensive and widely scattered, it will not be feasible to consider the contributions individually. Instead, the subject matter will be classified according to experimental observations and theory, and will be presented in summary form. It should be noted that the appended list of references does not constitute a complete bibliography; it includes only those works quoted below. More extensive bibliographies are included in several of the references; see particularly references 7, 9, 28, 34, 38, 50, 52, 54, a "Bibliography on Powder Metallurgy" published by the Library of Congress and a pamphlet published by the Metals Disintegrating Co. entitled "The Field of Powder Metallurgy and Bibliography." 11. Summary of Experimental Observations The following classified list is composed of general statements of established fact derived from the experimental results reported in the published literature. A few contested observations are included, because of their potential importance; these are labeled as such. Any satisfactory and complete theory must be capable of explaining all of the uncontested facts. Obviously, some important facts may be missing from this list and these may hold the key to the correct explanation of the sintering process, but the possible lack of such material should not deter attempts to understand the subject on the basis of what is available here. A, The Initial Bond at Room Temperature a. To a limited extent uncompressed powders and massive metals adhere at room temperature. Clean tin powder forms a weak "cake" on standing at room temperature, the strength increasing with time. Clean gold surfaces adhere on light con-tact, as do those of many other substances, including nickel.27 b. Upon compression the strength of the bond- is increased progres-ivelv. There is a limit of pressure

Jan 1, 1946

By A. A. Rauth

In this paper, the author derives a series of formulas from basic principles and illustrates the application of these formulas to practical grinding charge problems. The paper establishes the nearly proportional relationship of mill power to charge level and shows how this relationship can be used to advantage in the design, manufacture and operation of grinding mills. The procedures outlined offer a rapid means of anticipating the power requirements for a given charge or determining makeup charges for a given power reading. The theories which have been developed concerning the dynamics of grinding have been motivated largely by the desire to derive workable formulas for the accurate determination of grinding mill power. This accurate determination has always been handicapped by the large number of variables to be considered, some of which are mill diameter, length, speed, liner design, grinding charge and material density, volumetric mill loading, internal friction, and charge size and gradation. In efforts to determine mill power, attempts have been made to utilize torque concepts. The formulas derived consider the grinding mass as a rigid body and utilize factors that are based on empirical data so that the movement of the charge within the mill is compensated for. These formulas are of principal interest to the mill designer since he is charged with the responsibility of analyzing all of the variables and from them predicting a mill size and a motor size which are compatible both with each other and with the grinding job for which they were intended. The mill operator, on the other hand, has an entirely different problem. The mill dimensions are already established and so is the driving motor. The operator's main concern is to obtain maximum performance from the mill he already has. For him, the many variables which perplex the mill designer are fixed values. Mill diameter, length and speed are set and, to a large extent, so are the conditions inside the mill from which the torque formula advocates derive their empirical data. It is conceivable that if the major mill dimensions which affect power demand are held constant, and if the variables influencing empirical factors are held fairly constant, as they are in an operating mill, then the only major variable remaining which affects power is the level of the charge itself. Under this condition.

Jan 1, 1970

By O. W. Simmons, L. W. Eastwood, C. M. Craighead

The results of a preliminary study of 113 ternary titanium-base alloys are described. The compositions investigated were as follows: 1. Ternary titanium-carbon alloys containing copper, silicon, vanadium, chromium, manganese, iron, or cobalt. 2. Ternary titanium-nitrogen alloys containing chromium. 3. Ternary titanium-chromium alloys containing additions of vanadium, molybdenum, tungsten, cobalt, or nickel. 4. Ternary titanium-manganese alloys containing additions of silicon, chromium, tungsten, or iron. Tensile properties, minimum bend radii, hardnesses, response to heat treatment and aging treatment, and phase relationships for these alloys were determined. THIS is the second in a series of papers describing some of the results of the exploratory work on titanium alloys being conducted at Battelle Memorial Institute for the Wright-Patterson Air Force Base. The work with the binary alloy systems has been described in a previous publication.' This paper describes ternary titanium-base alloys as follows: 1. Ternary titanium-carbon alloys containing copper, silicon, vanadium, chromium, manganese, iron, or cobalt. 2. Ternary titanium-nitrogen alloys containing chromium. 3. Ternary titanium-chromium alloys containing additions of vanadium, molybdenum, tungsten, cobalt, or nickel. 4. Ternary titanium-manganese alloys containing additions of silicon, chromium, tungsten, or iron. As the preparation and fabrication of the 0.5-Ib experimental titanium alloy ingots to 14-ga sheet, as well as the methods of testing used in this work, have been described in the first paper of this series, Titanium Binary Alloys, no further discussion of these techniques will be given. Ternary Alloys Containing Carbon The following alloys of titanium, containing carbon and one other metal, were investigated: 1. 0.25 pct carbon; 1, 2.5, and 5 pct copper. 2. 0.25 pct carbon; 1, 2, and 3 pct silicon. 3. 0.25 pct carbon; 1, 2.5, and 5 pct vanadium. 4. 0.25 pct carbon; 2.5, 3.5, 5, 10, and 15 pct chromium. 5. 0.5 pct carbon; 2.5, 3.5, and 5 pct chromium. 6. 0.25 pct carbon; 1, 1.75, 2.5, 3.5, 5, 7.5, and 10 pct manganese. 7. 0.5 pct carbon; 1.75, 2.5, 3.5, 5, 7.5, and 10 pct manganese. 8. 0.25 pct carbon; 0.25, 0.5, 1, and 2 pct iron. 9. 0.25 pct carbon; 1, 2, and 3 pct cobalt.

Jan 1, 1951

By S. J. Hruska, G. M. Pound

The critical supersaturations for appreciable nucleation rate of cadmium crystals on copper and glass substrates at 186°Kwere measured as a junction of thermal-beam energy over a range of source temperatures between 616" and 839OK. There was no effect of source temperature on critical super saturation. This implies that the adsmbate prior to nucleation is in thermal equilibrium with the substrate. THE deposition of metallic vapors on solid substrates has been found to exhibit a critical behavior in that the rate of formation of deposit increases markedly when the intensity of the vapor source is increased slightly.* Evidence of the ability of sub- where Je is the flux which would arrive if the substrate were equilibrated with bulk condensate at the adsorbate temperature. The following work was undertaken to test this hypothesis. A) Energy Exchange Between Metallic Vapor and Substrates. When a freely translating atom collides with a stationary solid body its energy and momentum undergo changes which determine whether the atom is reflected or adsorbed. An atom is considered to be reflected if it returns to a freely translating state after remaining under the influence of the body for only a time comparable to the period of oscillation of atoms on the surface. An atom which remains for a longer time is said to be in an adsorbed state. The parameter which describes the energy transfer occurring at the interface is the thermal-accommodation coefficient which may be defined in terms of energy as Ei = average energy of impingent atoms, Eeq = average energy of an emergent atom which has equilibrated with the substrate, and Eem = average energy of an emergent atom. If a temperature is assigned to each of these energies, we have at as defined by Knudsen.2 Since this allows no distinction between reflected and evaporated atoms, a more specific definition is introduced for the present purposes, namely 71 = probability that an impingent atom is transferred to an adsorbed state, aj = thermal-accommodation coefficient for reflected atoms, and aTc = thermal-accommodation coefficient for adsorbed atoms. During a time t,, the mean stay time, prior to evaporation the adsorbed atom (adatom) will interact with the substrate and this will have the net effect of transferring the adatom towards a state of

Jan 1, 1964

F. L. Clerc, Chicago, Ill. (communication to the Secretary): On page 681 in Mr. Winslow's paper, he refers to me as having "advocated the view that the ores were derived from the patches of Coal-

Jan 1, 1895

By AIME

Cores must be cut in half to secure workable samples for saturation, porosity, and permeability tests. They come from the field labeled as to the type of core, well, and depth from which they came.

Jan 1, 1948

By Charles A. Lindberg

Mobile cranes on tires are perhaps the most important accessory in truck-haulage pits. They usually are of 20-ton capacity at short radius and with outriggers but have considerable overload capacity. Standard booms are 30 ft but have 10-ft extensions with which they are usually operated. Cranes have two engines, both originally gasoline, but 150-hp Diesel engines have been found more reliable for the propulsion motor, the 100-hp gasoline motors being retained for hoisting. Pro- visions are made for dropping the ballast counter- weight to reduce axle weights to legal limits for highway travel. The weights are carried on a regular truck or are transported on an extra trailer axle behind the crane. Tractors-Probably equalling the cranes in usefulness are the track-laying tractors which are used to prepare roads and other surfaces, to clean up at the shovel, and for dozing on stripping dumps. A new type of tractor mounted on rubber tires has been tried out on the Mesabi Range for the past year and a half. The advantage of this design is its mobility which makes it capable of taking care of the spill at the shovel and then running to the dump to clean up. Alternating between these two jobs, it relieves heavy tractors that can be used to better advantage on heavier work that does not require so much traveling. This tractor can travel at speeds of 12 to 13 mph and is designed to facilitate repair of the expendable parts. Weaknesses have developed in the internal construction which have seriously marred the performance record of this unit, but when used within its capacity it is quite successful.

Jan 1, 1949

By Charles D. Walcott

The following acts of the Directors are reported for the information of members At a meeting held June 20, 1907, Dr. Charles D. Walcott, Director of the U. S. Geological Survey, Washington, D. C., having been recommended by unanimous vote of the Council, was unanimously elected an Honorary Member of the American Institute of Mining Engineers, in recognition of his personal services to American geology, and of his generous co-operation with this Institute, to the Transactions of which he has not only himself made valuable contributions, but has also encouraged the preparation of such contributions by the members of the U. S. Geological Survey under his charge, his liberal policy in this respect having gone so far as to permit the preliminary publication by the Institute of important results reached by the geologists of that Survey, even before their final and full publication as public documents. This wise and generous course has not only brought the U. S. Geological Survey into intimate and sympathetic relations with the mining industry of the world, but has also enriched the Transactions of the Institute, especially in the department of the science of ore-deposits, with many valuable papers. At a meeting held Jan. 14, 1908, Mr. Charles Kirchhoff was unanimously re-elected a Trustee of the United Engineering Society, to serve for a second term of three years. At a meeting held Feb. 18, 1908, directly after the adjournment of the annual meeting of the Institute, the following officers were elected for the ensuing year: President, James Gayley: Vice-President, James Douglas; Secretary, R. W. Raymond; Treasurer, Frank Lyman.

Mar 1, 1908

G. A. ROUSH,* South Bethlehem, Pa. (written discussion?).-Mr. Frey is correct in his impression that ice floats, but "frazil" ice happens to be the exception to the rule. The requirements for the formation of

Jan 12, 1919

James W. Neill, Salt Lake City, Utah: Mr. Keller observes, in his interesting paper, that his copper mattes show a constant tenor of 21 to 23 per cent. sulphur; and continues," Many of these analy-

Jan 1, 1894

By R. W. M. Lai

This paper presents a simple flotation kinetics model (Lai, 1981) along with a method of presenting the model in an informative graphical form. Examples are given for evaluating various flotation conditions and different ore types.

Jan 1, 1983

INTRODUCTION The mineral sample is the fundamental unit upon which the mineral appraisal is built. Values derived from the sample are the most important quantitative measurements made in the total evaluation process. The sample value

Jan 1, 1980

By Major William R. King U. S. Engineer

My attention was drawn to this subject just twenty years ago this month, when I was detailed to rebuild one of the bridges in Richmond that had been burned during the evacuation. We took pos

Jan 1, 1886