Search Documents

By Ralph Hultgren

FEW phase diagrams of alloys composed of two transition metals have been adequately studied, probably because of the high melting points involved. Transition metals are the elements that have inner shells incompletely filled with electrons. They comprise groups IIIa to Villa of the periodic table, including more than half of all metals. We have chosen to study two systems whose comparatively low melting points allowed the alloys to be melted in a molybdenum resistance furnace. The nickel-palladium system proved to consist of a simple series of solid solutions, but iron-palladium manifested several remarkable features. The main characteristics of the latter diagram were decisively established, but lack of time prevented precise determination of phase boundaries. The gamma to alpha transformation in this system is unusual and warrants further study. Grigorjew1 determined the liquidus and solidus of the iron-palladium system by thermal methods. He found a minimum melting point, but no eutectic. He also found that palladium lowered the gamma to alpha and raised the gamma to delta transformation temperatures of iron, with a complete series of solid solutions existing between gamma iron and palladium. His measurements also indicated a compound or super-lattice near the composition FePd3. Jellinghaus2 found that annealing at 500° C. greatly increased the magnetic coercive force of an alloy of composition FePd. X-ray dif-fraction photographs showed that a tetragonal ordered phase had formed during the anneal.

Jan 1, 1939

By A. Soundraraj, S. Singh, R. C. Deshpande

THE detonation of a high-explosive charge having a metal-lined conical cavity (shaped charge) results in a fast-moving jet and a slow-moving slug.1-4 Clark and Bruckner reported the metallographic studies of a cast-iron slug. The present note describes the metallographic studies of a copper slug and discusses the principle of flow involved. The shaped charge consisted of a 5-cm diam cylinder of cast high explosive (60-40 RDX-TNT mixture) having a 45 deg and 0.16-cm thick copper cone. The copper (99.5 pct purity) had a grain size of 0.06 to 0.08 mm diam and a hardness of 65 to 75 Hv. These were fired into a deep container of water and the slugs were recovered undamaged. The longitudinal and transverse sections of the slug were polished, etched, and examined for mi-crostructural changes. Macroexamination revealed a radial grain flow inwards towards the center and a downward component of flow towards the base of the slug. Fig. 1 shows schematically the micro-structural changes observed on the longitudinal section of the slug. The region D near the apex and also along the outer surface of the slug was characterized by the presence of heavily deformed and twinned grains. Some of the grains were having bent or crossed twins, Fig. 2. The grain size in this region was of the same order as that of the

Jan 1, 1960

By Ralph Hultgren

FEW phase diagrams of alloys composed of two transition metals have been adequately studied, probably because of the high melting points involved. Transition metals are the elements that have inner shells incompletely filled with electrons. They comprise groups IIIa to VIIIa of the periodic table, including more than half of all metals. We have chosen to study two systems whose comparatively low melting points allowed the alloys to be melted in a molybdenum resistance furnace. The nickel-palladium system proved to consist of a simple series of solid solutions, but iron-palladium manifested several remarkable features. The main characteristics of the latter diagram were decisively established, but lack of time prevented precise determination of phase boundaries. The gamma to alpha transformation in this system is unusual and warrants further study. Grigorjew1 determined the liquidus and solidus of the iron-palladium system by thermal methods. He found a minimum melting point, but no eutectic. He also found that palladium lowered the gamma to alpha and raised the gamma to delta transformation temperatures of iron, with a complete series of solid solutions existing between gamma iron and palladium. His measurements also indicated a compound or super-lattice near the composition FePd3. Jellinghaus2 found that annealing at 500° C. greatly increased the magnetic coercive force of an alloy of composition FePd. X-ray dif-fraction photographs showed that a tetragonal ordered phase had formed during the anneal.

Jan 1, 1939

By L. W. Kemph

The thermal expansion characteristics of aluminum alloys have been examined by several investigators, among whom may be mentioned Shakespear,' Schulz,2 Hidnert13 Hidnert and Sweeney4 and McCullough.' Shakespear compared the expansion of a series of aluminum alloys containing 14 per cent copper, with separate additions of about 1 per cent each of manganese, tin and zinc with that of pure copper. Schulz examined the expansion of aluminum and zinc and some aluminum-zinc alloys. Hidnert determined with a high degree of precision the exp:tnsion characteristics of pure aluminum, some aluminum-copper, aluminum-zinc, aluminum-silicon and some commercial alloys.' Hidnert and Sweeney examined the expansion characteristics of aluminum-beryllium alloys. McCullough, by an interferometer method, determined the expansivity of some aluminum-copper, aluminum-magnesium, aluminum-iron, aluminum-nickel, aluminum-silicon and aluminum-manganese alloys. Incidental to an investigation carried out during the past six years and leading to the development and exploit,ation of an aluminum piston alloy of relatively low thermal expansivity, the expansion characteristics of a wide variety of alloys were examined. Some of the data which might be of general interest are gathered in this paper. Experimental Procedure The apparatus used was essentially similar to those developed by the Bureau of Standards6 and Howard Scott,? with a few minor changes for expediency. The specimen was approximately 4 in. long and the differential length changes between specimen and the quartz tube were

Jan 1, 1933

By L. R. Jackson

It is convenient to have a consistent system of notation that will allow the representation of the entire range of complex stresses from hydrostatic compression to hydrostatic tension on plastic flow in a single diagram. Such a system is provided by making use of the fact that any complex stress system can be resolved into a hydrostatic tension or compression and a pure shear. Consider a stress system having the principal stresses This system can be resolved into a new system consisting of the three components and three pure shears. If Sm is positive, the net stress effect is hydrostatic tension; if it is negative, the effect is hydrostatic compression. In order to produce a systematic notation, a quantity that will be referred to as the "triaxial ratio" will be defined by the equation _ Sm Tr = Sm - Sm is given by Eq. I and Sl is the absolute magnitude of the largest principal stress without regard to sign. Table I lists the triaxial ratios for various common systems. Table i.—Triaxid Ratios for Various CommonSyslems Triaxial Ratio Stress System Tr Hydrostatic compression — SI - —St - -S³............................... -1 Torsion or shear -SI - S². S² = O..... O Simple tension SI. SI = SI = 0......... +0.33 Biaxial tension SI = S² S³ - 0......... +0.66 Hydrostatic tension +SI - +S³ = +S³. +1.00 Representation of Strains Strains will be plotted as "true" strains according to the system proposed by Ludwik.1

Jan 1, 1945

By George F. Comstock

It has been known for many years that the alloy containing 90 per cent. copper and 10 per cent. aluminum can be hardened, like steel, by quenching from a suitable temperature, and that the hardened alloy can be softened again by annealing or drawing the temper. It does not seem to be generally appreciated, however, that the effect of the first slight reheating after quenching is actually increased hardness, the softening effect not taking place until a certain temperature of "drawing" has been exceeded. This paper gives the results of a few experiments on various specimens of cast 10 per cent. aluminum bronze, quenched for maximum hardness, and subsequcntly annealed at different temperatures. The hardness measurements were made with both a scleroscope and a standard Swedish Brinell machine; some peculiarities of the scleroscope test on this material are described. The author is not aware of many previous investigations of the hardness of this alloy when quenched and drawn, but two important papers on the subject should be mentioned. The earliest was by Portevin and Arnou,1 in which it was stated that tempering quenched 10 per cent. aluminum bronze at 400" C. increased the hardness as compared with the quenched untempered alloy and that reheating above that temperature ' was necessary to obtain any softening effect. A later paper was by Seidell and Horvitz,2 who mentioned Portevin and Arnou's work, but did not report any increase in hardness obtained

Jan 1, 1925

By J. O. Lewis, Carl H. Beal

Introduction ............................... 492 Theories Relating to the Recovery of Oil.................. 493 Methods Commonly Employed for the Estimation of Future Production..... 495 Saturation Method........................... 495 Production Curve Method....................... 496 Production per Acre Method.....................: 496 Appraisal Curves.............................. 498 Derivation and Construction...................... 498 Comparison of Appraisal Curves of the Osage and Nowata Fields...... 505 Use of Appraisal Curves........................ 506 Accuracy of the Apprais?l Curves and Their Sources of Error........ 508 Relation Between Future Productions of Wells of Equal Output....... 510 Use of Appraisal Curves for the Derivation of Generalized Future Decline Curves. 513 Theory of Generalized Curves Showing the Decline in Production...... 513 Suggested Methods for Making Closer Estimates.............. 517 Use of Logarithmic Coordinate Paper.................... 518 Summary................................ 520 Introduction Oil wells usually reach their maximum daily output shortly after they are completed. From that time they decline in production, the rapidity of decline depending on the output of the wells and on other factork governing their productivity. The production curve of a well shows the amount of oil produced per unit of time for several consecutive periods; if the conditions affecting the rate of production are not changed by outside influences, the curve will be fairly regular, and, if projected, will furnish useful knowledge as to the future production of the well. By the aid of this knowledge the value of a property maybe judged, and proper depletion and depreciation charges may be made on' the books of the

Jan 1, 1918

By C. F. Cigliana

TO accommodate a large tonnage at high speed from a single level at San Manuel, a very flexible haulage system was designed to give maximum access to stoping areas, minimize delays, and pro- vide for safety. With these requirements as a guide, the haulage was laid out as a simple double loop with one-way traffic of continuous pull. These loops consist of two parallel drifts 100 ft apart, center to center. Haulage drifts are numbered from north to south, the northernmost being the No. 1 drift. This holds true on both the North and South haulage loops. Haulage drifts are connected at 1000-ft intervals with crossovers so that it is possible to bypass any given section that may be inaccessible. Two of these turnouts are double diamonds, one located on the approach to the rotary dumps at the hoisting shafts and the other on the departure from the dumps. The turnout on the approach or North haulage is 835 ft in front of the rotary dump, and the one on the departure, or South haulage, is 1058 ft from the dump. This type of turnout allows trains coming down either haulage drift No. 1 or No. 2 to be routed into either shaft and expedites movement by avoiding delays due to congestion in the dumping area. The double diamond on the return haulage loop facilitates returning empty ore trains to the panels.

Jan 5, 1958

By Paul Sterling

The general impression regarding the preparation of merchantable anthracite is that it is confined to a colossal, grimy structure, called a " coal-breaker." This name is a misnomer; for the desired result is not to break the coal, but to prevent its being broken. Preparation may be said to begin at the face of the chamber, with the mining and loading of the coal. Local conditions vary, not only ill the same field or basin, but also in the same mine, so that there is no fixed empirical rule governing the method of blasting or cutting coal. Tests should be made, when possible, to determine the explosive, or the mechanical coal-cutter, which will produce the largest percentage of what are locally known as " lump " and " prepared sizes " of anthracite. The prepared sizes are those mostly consumed for clomestic purposes. All other sizes might be called by-products of the anthracite industry; for they are not especially desirable, being the degradation resulting from the mining and handling of a brittle or laminated material. Being low in volatile combustible matter, anthracite burns most successfully when nearly of a uniform size, permitting the easy passage of air through the voids. This accounts for the large number of sizes into which the coal is separated. Table I. gives the various sizes, the diameter of ring over and through which each size is made, and the usual purpose for which it is employed.

Jan 1, 1912

By AIME AIME

A REQUEST for information as to the details of activities of the Engineering Council was made by the Joint Conference Committee for the benefit of the new American Engineering Council. , This request was complied with, and the scheduled reply so succinctly sets forth the activities of the old Council as well as the scope of possible activities of ,the new Council, about whose efforts there has been much discussion, .that it' is given herewith in full, except the 'budget which is summarized.

Jan 1, 1920

By John Griffen

DURING the past year, purchases of coal-preparation equipment and the discussions and plant-scale tests conducted indicate that much attention is being given to better recoveries of coal by preparation plants and improved quality of the finer sizes to widen their market. In the anthracite regions the new equipment was predominantly for the cleaning of the steam sizes, much of it for treating No. 4 and No. 5 buckwheat. The units installed were largely coal-washing tables, Hydrotators, and Menzies cone separators.

Jan 1, 1944

By AIME AIME

THE session on milling methods on Monday afternoon.* with G. H. Clevenger, chairman of the Mining Methods Committee presiding, was well attended. However, none of the authors of the papers presented were present except Messrs. Taggart and Ince. The paper on "Elements of Operations of the Pneu¬matic Table," by Messrs. Taggart and. Lechmere-Oertel, was presented by Professor Taggart as was the paper on "Calculations in Ore Dressing," by Luyken and Bierbrauer, due to the absence of the authors.

Jan 1, 1929

By M. J. Sheriff, D. H. Smith, W. Macdonald

The paper outlines the basic procedure used in electrical system planning and design. Consideration is given to the use of applicable codes and standards, development and use of a system One Line Diagram, power availability, load requirements and power factor. Also discussed are the factors influencing the selection of power supply and distribution arrangement, voltage levels, system grounding, distribution and utilization equipment such as switchgear, transformers, motor control, cable systems, motors. Short circuit calculation methods and system protection are discussed.

Jan 1, 1978

By Shun-ichi Satoh

The electric arc welding of cast iron has been studied by Braune Lamberton, Schimpke, Kenyon, Gale Manufacturing Co., Wedemeyer Candy, Neese, Miller, Carter, American Welding Society, Namack Lebrun, Achenbach, Jansson, Xochendorffer and others.' The write of this paper has been able to obtain a series of cast irons, from gray tc white, without using cast-iron electrodes but by coating on wrought-iron bars mixtures of carborundum (Sic) and graphite (C). In this work, he found the curious phenomenon of barium carbonate.

Jan 1, 1929

The American Museum of Safety has installed a large collection of exhibits at 18 West 24th St., New York City, and extends a cordial invitation to the members of the Institute to visit this exhibition. The Museum is open daily from 9 am. until 5 p.m., and special arrangements will be made for the admission of a large party in the evening. The exhibition covers all phases of industrial and general safety, and also the important questions of sanitation and hygiene.

Jan 2, 1917

At its meeting on February 21, 1933, the Board of Directors the following resolution defining and expressing the policy of the Institute with respect to official participation or action in controversial matters: WHEREAS, the Board of Directors at its last meting passed the following resolution: "The Board of Directors, having been appealed to by several Local Sections for advice concerning the attitude and policy of the Institute relating to the endorsement of candidates for public office, the following statement of policy is formulated:

Jan 1, 1942

Plans for a multi-million dollar uranium mill in southeastern Utah were confirmed by Vanadium Corp. of America officials. Atomic Energy Commission has been dickering with two private firma for mill construction at Hite, Utah and Shiprock, N. Mex. Colorado Fuel & Iron has contracted to purchase all manufacturing business, plants and inventories of John A. Roebling's Sons Co., through a wholly owned subsidiary. CF&I currently the nation's ninth largest steel producer, will operate the new subsidiary under the Roebling name.

Jan 1, 1953

At its meeting on February 21, 1933, the Board of Directors the following resolution defining and expressing the policy of the Institute with respect to official participation or action in controversial matters: WHEREAS, the Board of Directors at its last meting passed the following resolution: "The Board of Directors, having been appealed to by several Local Sections for advice concerning the attitude and policy of the Institute relating to the endorsement of candidates for public office, the following statement of policy is formulated:

Jan 1, 1939

The members of the Institute will recall the account given in the March Bulletin of the inauguration exercises of the Engineering Foundation which was inhibited by an initial gift of $200,000 by Mr. Ambrose Swasey, to be administered by the United Engineering Society as trustees. The Engineering Foundation Board is now constituted as follows: GANG DUNN, Chairman, EDWARD D. ADAMS, Vice-Chairman FREDERICK R. HUTTON, Secretary, JOSEPH STRUTHERS, Treasurer, American Society of Civil Engineers. J. WALDO SMITH, CHARLES WARREN HUNT.

Jan 12, 1915

By W. Spencer Hutchinson

IT is the purpose of this paper to describe a method used to determine the corundum contents of samples of hard crystalline gneiss containing both corundum and red garnet. A chemical analysis of the rock for alumina would not fix the amount of corundum because at least three other constituent minerals of the rock, mica, feldspar, and garnet, contain alumina combined with silica. Following are the principal minerals found in the samples, together with their specific gravity and hardness as given by Dana:

Jan 6, 1913