Search Documents

By A. L. Mular

Two equations express the integral rate at which fines are produced from a homogeneous material: It has been demonstrated that the Gaudin-Meloy distribution for single fracture is equally applicable to multiple fracture and is related to the Gaudin-Schuhmann distribution at least when the distribution modulus a is close to unity. A, xoY was found to be independent of starting mass over the range studied when particle size was held constant. The equations are related to the input energy to the mill. In an earlier paper,' it was shown that when Mo g of uniformly sized homogeneous material is ground dry in a batch rod mill, the energy-size reduction equation is expressed at any time by the mass of unbroken starting material left at time t, ku is the size modulus of the portion Mo - Mt, and P is a constant that is generally equal to the distribution modulus a. If the power to the mill is constant, Et is proportional to time and Eq. 1 is rewritten where (Mo -Mt)/t is actually the integral rate at which fines are produced from a parent material, and A, is another constant. The size modulus, k,, is determined from the Gaudin-Schuhmann equation:2 where y is the cumulative fraction finer than any size x. Recently, Gaudin and Meloy derived a distribution equation for single fracture on the assumption that the random fracture of a homogeneous material produces daughter particles of similar shape. Their equation is given by where y is the cumulative fraction finer than size X, x, is the size of the unfractured parent, and r is designated the size ratio. Although Eq. 4 is derived for a single event, it should also approximately hold for a series of com-

Jan 1, 1962

By T. F. Witherbee

ON the 22d of November, „1879, white iron unexpectedly appeared while working the Cedar Point Furnace, Port Henry, N Y., on the following burden, calculated to turn out mill and foundry iron: Anthracite coal, - 3000 pounds. Connellsville coke, - 1500 pounds. Total, - 4500 pounds. Old Bed ore, - 3750 pounds. New Bed fine ore, - 2000 pounds. New Bed chunk ore, - 1000 pounds. Kearnev hematite ore, - 750 pounds. Total, - 7500 pounds. Magnesian limestone, - 1865 pounds. Common limestone, - 885 pounds. Total, - 2500 pounds. The production per week since making mill iron-from September 1st, 1879, to date, seven weeks-was 412 gross tons. Ore was not immediately taken off, as nothing serious was looked for. The iron for the next week graded from No. 4 to white, and in. six days the make was 274 1/2 tons. At 10 P.M., Friday, the 28th, a slip of-..4 feet occurred, and on Saturday, at 5 A.M., another of 3 feet on the south side and. 7- feet on the north side took place. At this time it was found that the south side had been hanging for over a week--a fact which had not been reported. Throwing off the wind, to produce slips. and reduce pressure, had been tried with no effect. The stock, as seen through the tuyeres, seemed to consist almost entirely of coal, with just enough infusible cinder to cement it into a mass through which the blast could not be forced. At 3.50 A.M., Sunday, the 30th, the first cinder seen in seventeen hours came into tuyeres Nos. 1, 2, 3, and 6, At 9.30 A.M. No. 3 was taken out to see if the stock

Jan 1, 1881

By John B. Hastings

Chief among the varied problems facing the mine-manager is that of vein-structure and origin, which is highly important as a guide to successful discovery and development. If metalliferous deposits can be traced to the intrusion of waters along definite lines, then is there something tangible for him to study. But when he is told by a geologist that metalliferous deposits are due to some other cause, like magmatic differentiation, while not perhaps discouraged, he is impressed with a vague sense of new worlds to be conquered. In 1897, while manager of the War Eagle mine at Rossland, B. C., where, previously, the ore-bodies had not been supposed to occur as veins, I suggested to visiting members of the Canadian Geological Survey that, perhaps, the structure of the pyrrhotite-bodies of that mine, which had been proved to occur along well-defined fractures, might throw some light on the similar deposits of Sudbury, then held to be basic aggregations from the original magma. Later investigation has at least provoked discussion of this last deduction, questioning its correctness and suggesting that, perhaps, the deposits are actual veins. The following extract from a paper by J. E. Spurr' is quoted, because it sets forth Mr. Spurr's theory of the quartz-occurrences of the Silver Peak mines, which will be discussed in this article. It also graphically describes the attendant geological features. "The Drinkwater group of mines, which is the most important part of the Blair gold properties, and which has produced practically all of the million dollars' worth of ore, as above stated, may be taken as typical of the gold-veins which, though widespread and numerons, show a wonderful similarity of character. On the surface two adjacent veins outcrop, the Crowning Glory and the

Jan 1, 1906

By H. V. Churchill

THERE are two distinct methods of combating corrosive conditions. The first and most popular method is to choose a surface or material which will give adequate service under the specific and general conditions which are present. The second is a control or modification. of the corrosive conditions to the end that metals and materials which would be attacked and corroded without such control or modification may be used. Under the first method of attack of the corrosion problem may be grouped such devices as the selection of metals or alloys which offer great resistance or the use of protective coatings such as paints, lacquers or metallic coatings. Such procedures are exceedingly useful. It is, undoubtedly true that most of the problems of corrosion will be solved by recourse to this first method of attack. However, it must be remembered that there are many conditions in which metals are used where the choice of the particular metal to be used must depend upon other factors than corrosion behavior. Some of the factors which may govern the selection of metals for specific use are the physical and mechanical properties of the metals. But there is another factor which is of prime importance and that is relative price. It is the pressure of these factors of mechanical properties, physical characteristics, and relative price that has acted as the stimulus for the second method of combating corrosion. The producer and user of various metals is confronted with the fact that because of mechanical properties, physical characteristics, or price, the use of a particular metal is desirable even though the corrosion conditions are adverse to the use of the metal. In many cases, the successful use of the metal may be made even though it is impossible to protect the metal by coatings. This is rendered possible by control or modification of the corrosive media.

Jan 1, 1929

By John B. Hastings

CHIEF among the varied problems facing the mine-manager is that of vein-structure and origin, which is highly important as a guide to successful discovery and development. If metalliferous deposits can be traced to the intrusion of waters along definite lines, then is there something tangible for him to study. But when he is told by a geologist that metalliferous deposits are due to some other cause, like magmatic differentiation, while not perhaps discouraged, he is impressed with a vague sense of new worlds to be conquered. In 1897, while manager of the War Eagle mine at Rossland, B. C., where, previously, the ore-bodies had not been supposed to occur as veins, I suggested to visiting members of the Canadian Geological Survey that, perhaps, the structure of the pyrrhotite-bodies of that mine, which had been proved to occur along well-defined fractures, might throw some light on the similar deposits of Sudbury, then held to be basic aggregations from the original magma. Later investigation has at least provoked discussion of this last deduction, questioning its correctness and suggesting that, perhaps, the deposits are actual veins. The following extract from a paper by J. E. Spurr 1 is quoted, because it sets forth Mr. Spurr's theory of the quartz-occurrences of the Silver Peak mines, which will be discussed in this article. It also graphically describes the attendant geological features. '' The Drinkwater group of mines, which is the most important part of the Blair gold properties, and which has produced practically all of the million dollars' worth of ore, as above stated, may be taken as typical of the gold-veins which, though widespread and numerous, show a wonderful similarity of character. On the surface two adjacent veins outcrop, the Crowning Glory and the Drink-

Jan 1, 1913

By W. F. Hosford

W. F. Hosford, (Massachusetts Institute of Technology) —evelopment of methods for predicting the plastic anisotropy of textured metals is an important step toward the improvement of properties by texture control. The engineering value of the present analysis is indicated by the good agreement between prediction and experimental findings. The purpose of this discussion, however, is to point out the weakness of the assumptions on which the analysis is based. The authors state that "the relative width and thickness strains are believed to depend only on the slip direction" and accordingly they disregard the orientation of the active slip plane. where E,, cW, and et are the tensile, width, and thickness strains, A,, A,, and At are the angles between the tensile axis x, the width direction w, and the thickness direction t, respectively; and G,, GW, and 4 are the angles between the slip-plane normal and x, w, and t, respectively. Therefore, the ratio of width to thickness strains resulting from slip on a single system would be These relations hold regardless of whether the slip plane is a crystallographic plane of the {110}, (1121, or (123) type or whether noncrystallographic slip occurs. If noncrystallographic slip occurs, it might be reasonable to assume that the effective slip plane is the most highly stressed plane containing the slip direction. In this case the slip direction, S.D., the slip plane normal, S.P.N., and the tensile axis, x, are coplanar (Fig. 19) and the angles are related by following expressions: where 9 is the angle between t and the projection of the slip direction in the w-t plane (igs. 1 and 2). The normal strains, Eq. [9], become

Jan 1, 1963

By Richard L. Seal, Allan L. Turner

INTRODUCTION The chapter discusses the procedures and operations starting with the actual training of operations personnel with respect to a grinding mill circuit and a typical check-out and start-up of a grinding circuit before turning over the operating circuit to production personnel. For the purposes of this paper, it will be assumed that the mill circuit installation is at a new location or a new operation at an existing operation. Expansion of an existing grinding facility would probably require less time-consuming and less costly procedures than those that will be outlined here. There are numerous arrangements and types of equipment that can be used for grinding circuits. For example, the grinding could be wet or dry. The grinding mill could be a rod or ball mill or some combination. The circuit could be open or closed. The closed circuit classification could be accomplished with rake classifiers, spiral classifiers, cyclones, stationary screens, or vibrating screens. To limit the discussion, the grinding circuit shown on Figure I will be discussed. The circuit includes a dry ore feed by a belt conveyor (feeder) to a wet ball mill. The ball mill discharges to a cyclone feed pump box and pump. The pump feeds a cyclone type classifier with the cyclone underflow returning to the ball mill feed and cyclone overflow being the required grinding circuit product. For the purposes of this paper, it will also be assumed that the extensive overall preparation necessary for every start-up has been accomplished. These preparations are only outlined here as they have been adequately dealt with in recent papers. (1), (2), (3) The items in these preparations would include. 1. Appointment and indoctrination of the start-up organization. 2. Integration of the start-up into the overall project schedule. 3. Development of the specific start-up schedule. 4. Budget determination and monies appropriation.

Jan 1, 1982

By R. F. Mehl, M. Gensamer

Creep investigators have made extensive studies to determine the interrelation of stress, temperature and the tensile creep rates of metals. It has been suggested that at small stresses the secondary or constant creep rates obey a simple viscous law. Building upon this suggestion, departure from pure viscosity as stress increases may be expressed mathematically as a consequence of reversibly altered viscosity or "flowability" in the same sense that temperature change reversibly alters viscosity. From the index to alteration of viscosity, a value for the energy of secondary creep may be derived having the magnitude of the free energy of vaporized metal. The suggestion is made that application of stress alters the energy of secondary creep. Strain energy is argued to be but a minor factor in the energetics of secondary creep. A deformation mechanism involving the large energy associated with secondary creep implies a sort of solid self-diffusion process. Evidence indicates that creep strain above the recrystallization temperature takes place by crystallographically directed self-diffusion at grain boundaries and points of crystal defects. A self-diffusion theory of secondary creep is proposed, embracing the principles of the Dushman-Langmuir theory of solid diffusion. An equation is suggested whereby the rate of tensile creep may be related directly to the physical and structural character of the solid metal. Basis of Investigation Much of the investigation that has been given to the creep characteristics of metals and alloys has been directed toward studying the dependence of creep rate upon stress. Great interest has centered upon the approximately uniform rate of flow that has been demonstrated for numerous metals and alloys. At temperatures above the strain-hardening ranges of materials, this uniform rate frequently is attained after a relatively short period of initial rapid flow, and the period during which it persists determines for most practical purposes the useful life of the

Jan 1, 1938

By R. F. Mehl, M. Gensamer

Creep investigators have made extensive studies to determine the interrelation of stress, temperature and the tensile creep rates of metals. It has been suggested that at small stresses the secondary or constant creep rates obey a simple viscous law. Building upon this suggestion, departure from pure viscosity as stress increases may be expressed mathematically as a consequence of reversibly altered viscosity or "flowability" in the same sense that temperature change reversibly alters viscosity. From the index to alteration of viscosity, a value for the energy of secondary creep may be derived having the magnitude of the free energy of vaporized metal. The suggestion is made that application of stress alters the energy of secondary creep. Strain energy is argued to be but a minor factor in the energetics of secondary creep. A deformation mechanism involving the large energy associated with secondary creep implies a sort of solid self-diffusion process. Evidence indicates that creep strain above the recrystallization temperature takes place by crystallographically directed self-diffusion at grain boundaries and points of crystal defects. A self-diffusion theory of secondary creep is proposed, embracing the principles of the Dushman-Langmuir theory of solid diffusion. An equation is suggested whereby the rate of tensile creep may be related directly to the physical and structural character of the solid metal. Basis of Investigation Much of the investigation that has been given to the creep characteristics of metals and alloys has been directed toward studying the dependence of creep rate upon stress. Great interest has centered upon the approximately uniform rate of flow that has been demonstrated for numerous metals and alloys. At temperatures above the strain-hardening ranges of materials, this uniform rate frequently is attained after a relatively short period of initial rapid flow, and the period during which it persists determines for most practical purposes the useful life of the

Jan 1, 1938

By A. L. Blomfield

THE Golden Cycle Mining and Reduction Co. operates its custom mill at Colorado Springs on Cripple Creek ores exclusively. These ores are straight sulpho-tellurides, with practically no base metals such as Pb, Cu, Zn, As, or Sb. Upon entering the mill, the ore all passes through the sampler to storage bins, where beds of 5000 tons each are made to insure uniformity in roasting. CLASSIFICATION OF ORES For efficiency, it has been found advisable to separate the ores into two classes according to their line content. Other constituents have their effect, such as alumina and magnesia, but, speaking generally, these are roughly proportional to the line, which, as CaO, is used as the indicator. Class A contains not more than 2 per cent. CaO and comprises about 66 per cent. of the ore treated. Class B contains over 2 per cent. CaO, and comprises 34 per cent. of the ore treated. Typical analyses of both classes are as follows: Class A Class B Insol 56.70 75.90 Al203 2.30 3.40 Fe 3.26 3.48 CaO 1.57 5.12 S 1.79 1.80 Mg0 0.21 1.08 Ignition loss 3.20 6.50 99.03 97.28 The beds of each class of ore are made as large as possible with the available ore as it comes in, to avoid changing from one bed to the other any oftener than necessary. Each roaster will handle 50 percent. more of class A ore than of class B, with practically the same results. This necessitates changing the rate of feed for each new bed and tends toward a poor roast and loss of tonnage at each change.

Jan 8, 1918

By Damon H. McFadden

5.1-1. Geographic and Geologic Factors. Surface mines are located where the coal seam can be economically uncovered and where the product can be utilized competitively with other fuels. The planning and designing of a pit may follow various procedures. The sequence for consideration of the influential factors as considered here may not be complete for every pit, nor will it be necessary to be completely used in each design. It is suggested as a check and outline for the engineering approach. Controlling conditions for the layout should be listed and considered with the facilities and equipment for the exploitation. After these items, as listed below, have been discussed and the feasibility agreed upon, then the actual planning and design of the pit can be done. GEOGRAPHIC FEATURES. The location of the coal area sets the climatic stage. The rainfall, the temperature extremes, and the general weather conditions all affect the design of the pit. Overburden soil when wet may not be stackable and may be impossible to move by standard procedures. The coal seam itself may be so soft that it must not be traveled on when wet, as the losses may be the difference between a profitable venture and an unsuccessful one. Some equipment will work well on dry soil only, just as a dredge works only in the wet. The conditions must be checked and analyzed. Some equipment cannot handle frozen soil (wheel excavators), so temperature extremes must be noted. The extreme weather conditions may also govern the expected working days and therefore the ultimate production. The altitude (atmospheric pressure) may affect the equipment, and this should be checked. All of these conditions should be noted on the preliminary map of the area. GEOLOGIC FACTORS. The geologic and surface conditions of the coal field dictate the type of pit generally feasible. Rough terrain, rolling terrain,

Jan 1, 1968

By W. E. Forsythe

Different forms of optical pyrometers are discussed and the advantages and disadvantages of the different types for measuring high temperatures are pointed out. These advantages and disadvantages lead to the selection of the disappearing-filament type of optical pyrometer for most work. Attention is directed to the necessity for the use of a monochromatic screen with a pyrometer, which leads to a discussion of the meaning and use of the effective wave length of the screen. Methods of calibrating the optical pyrometer are outlined and it is shown that an optical pyrometer can be calibrated just as definitely as any other temperature-measuring device. Accuracy tests are included, in which it is shown that excellent results can be obtained by even untrained or slightly trained observers with this form of optical pyrometer. The various corrections that are necessary in this kind of work are indicated, including corrections for stray light, for absorption of windows, of smoke, and so forth. The troublesome problem of measuring the temperature of bodies that do not radiate like a black body is discussed and the corrections for reducing such readings to the true temperature are given for a number of different materials. Introduction The fundamental idea of temperature depends upon our temperature sense and bodies are said to be hot or cold depending upon the reaction of our hands or some other part of the body to the heat from the source investigated. For measuring the temperature some instrument must be devised, since the temperature of the source studied is apt to be so hot as to greatly injure any part of the body that comes near it, to say nothing about direct contact with it. Definition of Temperature.—The temperature scale is based upon two fixed points, the temperature of freezing water and the temperature of boiling water. This temperature interval, depending upon the scale

Jan 1, 1936

By W. E. Forsythe

Different forms of optical pyrometers are discussed and the advantages and disadvantages of the different types for measuring high temperatures are pointed out. These advantages and disadvantages lead to the selection of the disappearing-filament type of optical pyrometer for most work. Attention is directed to the necessity for the use of a monochromatic screen with a pyrometer, which leads to a discussion of the meaning and use of the effective wave length of the screen. Methods of calibrating the optical pyrometer are outlined and it is shown that an optical pyrometer can be calibrated just as definitely as any other temperature-measuring device. Accuracy tests are included, in which it is shown that excellent results can be obtained by even untrained or slightly trained observers with this form of optical pyrometer. The various corrections that are necessary in this kind of work are indicated, including corrections for stray light, for absorption of windows, of smoke, and so forth. The troublesome problem of measuring the temperature of bodies that do not radiate like a black body is discussed and the corrections for reducing such readings to the true temperature are given for a number of different materials. Introduction The fundamental idea of temperature depends upon our temperature sense and bodies are said to be hot or cold depending upon the reaction of our hands or some other part of the body to the heat from the source investigated. For measuring the temperature some instrument must be devised, since the temperature of the source studied is apt to be so hot as to greatly injure any part of the body that comes near it, to say nothing about direct contact with it. Definition of Temperature.—The temperature scale is based upon two fixed points, the temperature of freezing water and the temperature of boiling water. This temperature interval, depending upon the scale

Jan 1, 1936

By Michael B. Jones, Wayne R. Bruce, Cyrus W. Field

For more than a decade the Pacific Northwest has been a frontier of successful porphyry copper-molybdenum exploration. This vast region (about 2100 miles long, 350-500 miles wide) occupies a geologically complex mobile tectonic belt. It parallels the Western Cordillera from northern California-Nevada to southern Alaska-Yukon Territory, and west from the northern Rocky Mountain-Tintina Trenches to the Pacific margin. Right lateral displacement has occurred along major transcurrent faults that are sub parallel to the region and the transform Fairweather-Queen Charlotte fault zone separates the North American continental plate from the Pacific oceanic plate. Porphyry-type deposits are widespread, but producing mines are restricted to south and central British Columbia. Size and grade are variable (25 to +300 mt; 0.18 to 0.65% Cu with 0.014 to 0.049% MoS2; 0.14 to 0.28% MoS,) and secondary enrichment is normally unimportant. Metallization is genetically and spatially related to late quartz-feldspar porphyries that are within, marginal, or satellitic to composite batholithic intrusions. Radiometric ages of the plutons range from Miocene to Triassic-Jurassic (18 to 217 m.y. [million year] ). Country rocks are typically eugeosynclinal metasedimentary and metavolcanic assemblages of Permian to Jurassic age. Several of the older (pre-Late Cretaceous) deposits formed in submarine island arc environments and they may be genetically related to occurrences of volcanogenic sulfides in the greenstone country rocks. Deposition of bornite-chalcopyrite-molybdenite ores is controlled by contacts, breccias, and fault-fracture zones. Associated hydrothermal gangue minerals include biotite, orthoclase, sericite, kaolinite, quartz, anhydrite, and tourmaline. Isotopic data suggest a deep source for ore, gangue, and plutonic host rocks. Significant exploration features include porphyries, dike swarms, breccias, potassic alteration, barren quartz cores, gossans, and fringing halos of pyrite and propylitic alteration.

Jan 1, 1975

By Craig R. Barrett, Jack L. Lytton, Oleg D. Sherby

The types of substructures developed during high-temperature creep of (110)[001]-oriented polycrys-talline Fe-3.1 pct Si were examined by electroetching of dislocation sites. Edge dislocations were observed to accumulate adjacent to grain boundaries and poly-gonize perpendicular to their glide planes to form a "Pile-up" of nearly parallel tilt boundaries. The dislocation density developed within the grains during steady-state creep was found to increase with increasing stress. The formation of periodically spaced groups of edge dislocations along grain boundaries was observed, and it was proposed that these formed to relive bending stresses at grain boundary shear .faults. Grain boundary serrations developed at these faults, and it was suggested that this was a result of localized grain boundary migration at the polygonized groups. THE authors have conducted a series of high-temperature creep tests on (110)[001]-oriented poly-crystalline Fe-3.1 pct Si sheet. The creep specimens were examined at various stages of creep by means of electrolytic etching of dislocation sites using the chrome-acetic acid solution developed by Morris.' Hibbard and Dunn2 have demonstrated that the etch pits produced with this technique correspond to single dislocations. It is the purpose of this paper to present and discuss the dislocation substructures which were formed during high-temperature creep at constant stress. EXPERIMENTAL PROCEDURES The polycrystalline Fe-3.1 pct Si sheet employed in this study contained a (110)[001] texture. This texture was quite strong, and the elastic properties of the sheet closely approached those of a single crystal of iron.3,4 A typical analysis in weight percent for this material is 3.1 Si, 0.1 Mn, 0.003 C,

Jan 1, 1965

By Charles Wraith

THE property of the Roan Antelope Copper Mines, Ltd., is situated at Luanshya, north-central part of Northern Rhodesia, and is connected with the main line of the Rhodesia Railways, Ltd., by a 24-mile branch line from N'dola. Most of the material and supplies that are not available in Africa are shipped into the country via Beira, on the East Coast of Africa, a distance of 1473 miles from Luanshya and the nearest ocean port. The output of copper is shipped by rail to Beira and thence by boat to the market. Passenger travel is mostly via Cape Town, a distance of 2162 miles from Luanshya. Excellent passenger trains operate on regular schedules between Cape Town and Northern Rhodesia. Luanshya is 13° south of the equator at an elevation of 4000 ft. above sea level, and has a mild healthful climate. During the rainy season, from October to March, the rainfall averages 53 in. The area is pro-fusely covered with vegetation. An ample supply of water for industrial and domestic purposes is available throughout the year. The more important supplies for smelting purposes, such as wood, coal, limestone, silica, quartzite, and clay for "dolly" mud, are con-veniently available. Excellent grades of coal, coke and firebrick are obtained from the Wankie Colliery Co., Ltd., Southern Rhodesia. The Wankie colliery has just completed the erection of equipment for the manufacture of silica brick. An ample supply of quartzite of good grade is available for this purpose. Silica brick is also obtained from the Belgian Congo and from India. Limestone is quarried from a large deposit a few miles from Bwana Mkubwa, which is 30 miles by rail from the smelter. An abundant supply of clay for "dolly" mud and for lining launders is available within a short distance of the smelter.

Jan 1, 1933

By E. R. Parker, R. H. Thielemann

The conventional short-time tensile test provides a reliable means of predicting the sustained load-carrying capacity of steels only when the temperature is such that continuous plastic flow does not occur. At elevated temperatures, stresses considerably less than the short-time rupture value may produce continuous flow, with fracture occurring only after long periods of time. The amount of flow or creep accompanying failure varies for different steels, and depends, to a large extent, on the temperature and the duration of the test. Service records of cracking stills, steam superheaters and high-temperature boilers have shown that brittle fractures sometimes occur with little or no warning. In installations of this type, localized stresses are often encountered, and steels must be capable of withstanding a certain amount of deformation without fracture. The sustained-load rupture test determines the expected life and corresponding ductility of steels at various stresses and temperatures. It also yields additional information regarding the effect of micro-structure and metallurgical stability on the high-temperature properties. Present Status of Sustained-load Rupture Test The sustained-load rupture test conducted at elevated temperatures is not entirely new. Dr. Zay Jeffriesl presented in 1919 the results of a large number of rupture tests made on copper, iron and tungsten. These tests were made with various strain rates and at temperatures ranging from the boiling point of liquid air to 1000° C. At that time he observed the interesting phenomenon characteristic of metals, that a temperature exists below which a metal is ductile and breaks with a transcrystalline fracture (through the grain) and above which the metal is brittle and breaks with an intergranular fracture (through the grain boundaries). He observed that this temperature varied with the testing speed, and that a minimum temperature, slightly above the recrystallization temperature, existed at which the cohesion of the grains themselves was

Jan 1, 1939

By R. H. Thielemann, E. R. Parker

The conventional short-time tensile test provides a reliable means of predicting the sustained load-carrying capacity of steels only when the temperature is such that continuous plastic flow does not occur. At elevated temperatures, stresses considerably less than the short-time rupture value may produce continuous flow, with fracture occurring only after long periods of time. The amount of flow or creep accompanying failure varies for different steels, and depends, to a large extent, on the temperature and the duration of the test. Service records of cracking stills, steam superheaters and high-temperature boilers have shown that brittle fractures sometimes occur with little or no warning. In installations of this type, localized stresses are often encountered, and steels must be capable of withstanding a certain amount of deformation without fracture. The sustained-load rupture test determines the expected life and corresponding ductility of steels at various stresses and temperatures. It also yields additional information regarding the effect of micro-structure and metallurgical stability on the high-temperature properties. Present Status of Sustained-load Rupture Test The sustained-load rupture test conducted at elevated temperatures is not entirely new. Dr. Zay Jeffriesl presented in 1919 the results of a large number of rupture tests made on copper, iron and tungsten. These tests were made with various strain rates and at temperatures ranging from the boiling point of liquid air to 1000° C. At that time he observed the interesting phenomenon characteristic of metals, that a temperature exists below which a metal is ductile and breaks with a transcrystalline fracture (through the grain) and above which the metal is brittle and breaks with an intergranular fracture (through the grain boundaries). He observed that this temperature varied with the testing speed, and that a minimum temperature, slightly above the recrystallization temperature, existed at which the cohesion of the grains themselves was

Jan 1, 1939

By J. D. Price, W. M. Bertholf

One of the chief difficulties with which the operator of a coal washing plant has been forced to contend is the handling of the very fine coal. First he has the problem of separating the fine coal from washery water. This is usually accomplished by the use of settling cones or Dorr thickeners: in either event the separated fine coal contains a high amount (40 to 80 pct) of water and, somewhat loosely, dependent upon the size of the coal particles present, may be known as sludge or slurry. His second problem is the satisfactory further dewatering of such separated sludge and/or slurry.

Jan 1, 1949

By Frederick M. Becket

SHORTLY after the Armistice there appeared a few references to numerous attempts that had been made to produce steel without the aid of manganese, or at least with manganese in abnormally low percentage. Some years later, during two consecutive days of train travel, I had excellent opportunity to read Sir Robert Hadfield's book, entitled "Metallurgy-Its Influence on Modern Progress," and also his paper, "The Metal Manganese and Its Properties : Also the Production of Ferro-Manganese and Its History," presented at the spring meeting of the Iron and Steel Institute, 1927. Both the book and the paper are most interesting historically to makers of alloy steels and

Jan 1, 1931