Search Documents

By H. E. Wheeler

THE work described was carried out during 1917 and 1918 at the testing laboratory of Watertown Arsenal at the instigation of the Nitrate Division and later with the concurrence of the Cannon Section of, the Ordnance Department, U. S. A. The experiments follow three principal lines of work: First, the effect of nitrogen under pressure on steel containers of various compositions at a red heat; second, the effect of decomposing ammonia on various alloy steels, iron, and non-ferrous alloys; third, a new theory of the erosion of guns in respect to the effect of nitrogen in steel. PART I In the Haber process for the manufacture of ammonia from its elements, it is necessary to have nitrogen and hydrogen of 1500 lb. per sq. in. (105.5 kg. per sq. cm.) at a temperature of 500 to 600° C. The steel containers for these gases gave trouble by failing without apparent cause. When the General Chemical Co. began to develop its method for the production of ammonia, it experienced the same difficulty and, knowing that the Haber process had solved the difficulty by the use of alloy steels, it made several small steel bottles of different compositions and kept them filled with these gases at this pressure and temperature until they failed. The time of service varied from a few days, for the plain steel casting, to two years for a chrome-vanadium forging. Four of these steel bottles were sent to this laboratory for investigation; they were a plain carbon-steel forging, a nickel-steel forging, a chrome-vanadium steel forging, and a chrome-steel forging. The time of service was as follows: plain carbon steel, 4 mo.; nickel steel, 6 mo.; chrome-vanadium steel, over 2 yr.; chrome steel, 4 mo. When these containers were cut open and the cross-section surface polished, they showed an inside zone with a different luster from the rest of the metal. Upon etching, this zone was almost unaffected while the rest of the steel etched normally.

Jan 4, 1920

By H. V. Welch

In this paper, as prepared for delivery at the Southern California regional meeting on Oct. 14, 1948, it was thought best to interpret the term "economics" in a rather broad manner and to include, in addition to the material losses and recoveries and associated monetary values (Part I), a limited discussion of the increased difficulties or the particular problem and the special requirements, as the particle sizes of the suspended particles range down from the relatively coarse to 100, to 10, to 1 micron or even to a fraction of one micron (Part II). Further, it is not quite in order to overlook entirely the community and individual health problems, although space requires the economics of this to be considered only very incompletely. Therefore, Part III, covering this phase of the subject, is very limited. This paper, then, is divided into 5 parts or headings as follows: I Losses and/or values in suspended solids. II Particle size. III Dust and fumes in community and individual living. IV Means and Procedures for dust and fume collection. V Description or examples of specific equipment in service and of the several types used for dust and fume collection. Because of the wide extent and wealth of subject material available and the space and time limitation imposed, presentation and discussion are less than originally planned. I—Losses and/or Values in Suspended Solids The weight involved in moving streams of industrial plant gases is commonly not appreciated, neither is their carrying power in the weight of solids maintained in suspension and moved with the gas stream from a point of origin or pick-up to a point of dissipation or settlement. These, however, are major weight figures; for example, in a modern iron blast furnace there may be five tons of gas for every ton of iron produced and by the time this blast furnace gas has been burned in stoves or under boilers the weight of gas discharged to atmosphere is on the order of eight times the weight of iron produced. Similarly for nonferrous metallurgy there may readily be from 10 to 20 times the weight of gases discharged to atmosphere as there is metal produced. A cement kiln in operation or a kiln in service to produce metallurgical lime may have on the order of 5 to 6 times the weight of stack gases as of clinker or lime produced, and at least the cement kiln, because of the very fine nature of its feed, is a very heavy dust producer. It may be noted that there have been two developments in progress for nearly three decades. Both are extraordinary in the industrial economics effected and in their ready availability to ever larger units of operation and their ever widening importance in industry, and both are productive of great quantities of finely divided material in furnacing. The first of these is the flotation process for ores, especially the metallics such as copper, lead, and zinc; and the second, powdered fuel combustion for power plant, industrial plants and metallurgical operations. Today, new developments, for example, flotation for the nonmetallics such as higher grade limestone for cement manufacture which requires still finer grinding and the powdered-coal-fired boilers with production ratings of over 1,000,000 lb of steam per hr, bring still more concentrated and hugely increased quantities of stack emission. Perhaps the honors for the greatest interest in the quantities and values escaping in waste furnace and equipment gases belong to the nonferrous metallurgical operations. Their record of achievement in the installation of dust and fume collection equipment, largely baghouses or Cottrell electrical precipitators, is exceeded by no other industry. Something of the magnitude and variety of equipment utilized in such recovery systems was covered by the writer in two papers presented to the Institute some 10 years ago.1,2 It is not intended to repeat the material of those articles, but it is thought that they complement this offering and should be noted. COPPER ROASTERS As the copper roasters are the first of the series of furnaces handling the copper-bearing concentrates in the usual copper smelter of today, it is in order to make them the first consideration. Multiple hearth sulphide roasters, not hard driven, often maintain their dust loss through exit gases at 3 pet or below of feed to furnace; in hard-driven or maximum-driven furnaces, exit gas losses often approximate 7 pet of charge with a ±2 pet variation for special conditions prevailing at some plants. A 5 pet loss of feed in a roaster gas exit, unless reclaimed, often makes the difference between a profit and loss operation, and in many cases substantial recovery is the very basis of dividend payments. As there is available very practical and successful equipment for the collection of the

Jan 1, 1950

By Alec M. Crowell, J. W. Sanders

While the production of crude oil and condensate in South Arkansas increased only 1.7 per cent over the 1940 figure, complete utilization of gas produced with the oil and condensate, and heretofore wasted, was beginning to be evidenced. There were 26,229,264 bbl. of oil and condensate produced in South Arkansas during 1941, as against 25,790,380 bbl. for the year 1940. (Fig. I.) Since 1936, deep producing sands have been discovered in 18 fields and during that period only 40 per cent of the total state production has come from Upper Cretaceous formations while 60 per cent came from the Lower Cretaceous and Jurassic formations. The gas produced with crude oil and condensate from the latter formation contains large quantities of hydrogen sulphide, the maximum being 6900 grains per 100 cu. ft. in the Patton pool of Lafayette County. Gas Utilization During the latter part of 1940 and the early part of 1941, pilot plants were placed in operation to determine whether the hydrogen sulphide and deleterious material in South Arkansas gases could be removed economically. The Federal Government desired to build a large aluminum plant in the Ouachita Valley and was seeking cheap fuel for the generation of electricity. The fact that the gases were produced with appreciable quantities of crude oil and condensate made it available at a very low price, since the state's conservation law prohibits the flaring of any gas. As a result of these experiments the first large-scale unit for the processing of gases containing hydrogen sulphide was placed in operation on Sept. I, 1941. The plant is in the Magnolia oil field, Columbia County. It processes residue gas from the Shell Oil Company's gasoline plant in that field and also raw gas from the Village field, 6 miles east of the Magnolia field. The gas entering the desulphuri-zation unit is laden with approximately 1400 grains of hydrogen sulphide per 100 cu. ft. and is stripped to a content of 4 grains per 100 cu. ft. The capacity of the plant is 15 million cu. ft. of gas treated daily under a pressure of 160 lb. per sq. in. The cost of treatment, exclusive of depreciation, is appreciably less than I per 1000 cubic feet. Two other plants of much greater capacity have been announced and priorities have been granted, which should bring the total amount of gas treated to 150 million cu. ft. daily. The gas to be treated will have a maximum hydrogen sulphide content of 4500 grains per 100 cu. ft. and will be processed under a pressure of 600 lb. per sq. in. These developments are something entirely new in field practice for the industry. The fact that this heretofore wasted gas is available at very low cost has led to the location of some eight war industries within the state, in addition to the alu-minum plant. Recovery OF Sulphur The Susearch Corporation and the Southern Acid and Sulphur Co. placed in operation during 1941 pilot plants to de-

Jan 1, 1942

By Alec M. Crowell, Harry P. McClintock

Production of oil and gas condensate from the 45 oil and gas fields of South Arkansas increased for the eighth consecutive year, the production for 1943 being 27,605,647 bbl. Six new pools were discovered during 1943, bringing the state's crude oil and condensate reserve to 475 million barrels, a net increase of 70 million barrels for the year. The gross increase in proven reserve was 98 million barrels, from which, of course, is subtracted production of approximately 28 million barrels to reach the net figure of 70 million barrels. There were 35 more wildcats in 1943 than in 1942, and 29 more wells were drilled in fields of the state. Sixteen companies operated exploratory crews during the year for a total of 677 crew weeks, divided as follows: 563 weeks seismograph, 111 weeks gravity and 3 weeks core drill. There was a decided increase in gravity work and a decrease in seismic work. The year started with 15 seismic crews and ended with 5 seismograph and z gravimeter crews. Geologically, it is interesting that the number of wells bottomed in Gulf, Comanche, and Jurassic strata were near equal for the year 1943. During 1942 Jurassic was much higher than the other two. However, Jurassic still led in wildcats for the year 1943. Abandoment of wells in the stripper areas of the state reached about the same figure for the year 1943 as for the year 1942; that is, 145 wells were permanently abandoned. However, 243 wells were drilled in 1943, as against 184 for the previous year. The completions for the year were divided into 103 dry holes, 137 oil and condensate wells and 3 dry gas wells. Among new developments perhaps the most significant was the pressure-main-tenance project for the Midway field of Lafayette County, which is utilizing fresh water as the maintenance medium. This is the first fresh-water pressure-maintenance operation during primary production of an oil field in the United States. The operator of the project, Barnsdall Oil Co., estimates that the ultimate recovery of oil from this field will be increased from 32.5 to 65 million barrels. The Midway pool is of the dissolved-gas type, but a similar project is getting underway for the Magnolia field, Columbia County, a pool of the gas-cap and water-drive type. Dual completion of wells, on concurrent production from two productive zones through a single well bore, became common practice in South Arkansas during the year. As the year ended, some 50 wells had been dually completed and it was estimated that the first 37 of these wells represented a saving of more than 2 1/4 million dollars and a saving in steel of 7000 tons. The majority of the wells dually completed were those reaching depths in the neighborhood of 9000 ft. below the surface and initially productive there. Selective completion at lesser depths in the same well bore proved mechanically feasible and economically sound. The year was marked by the successful completion and placing into operation of three large natural-gas desulphurization

Jan 1, 1944

By Harry P. McClintock, Alec M. Crowell

Production of oil and gas condensate from the 45 oil and gas fields of South Arkansas increased for the eighth consecutive year, the production for 1943 being 27,605,647 bbl. Six new pools were discovered during 1943, bringing the state's crude oil and condensate reserve to 475 million barrels, a net increase of 70 million barrels for the year. The gross increase in proven reserve was 98 million barrels, from which, of course, is subtracted production of approximately 28 million barrels to reach the net figure of 70 million barrels. There were 35 more wildcats in 1943 than in 1942, and 29 more wells were drilled in fields of the state. Sixteen companies operated exploratory crews during the year for a total of 677 crew weeks, divided as follows: 563 weeks seismograph, 111 weeks gravity and 3 weeks core drill. There was a decided increase in gravity work and a decrease in seismic work. The year started with 15 seismic crews and ended with 5 seismograph and z gravimeter crews. Geologically, it is interesting that the number of wells bottomed in Gulf, Comanche, and Jurassic strata were near equal for the year 1943. During 1942 Jurassic was much higher than the other two. However, Jurassic still led in wildcats for the year 1943. Abandoment of wells in the stripper areas of the state reached about the same figure for the year 1943 as for the year 1942; that is, 145 wells were permanently abandoned. However, 243 wells were drilled in 1943, as against 184 for the previous year. The completions for the year were divided into 103 dry holes, 137 oil and condensate wells and 3 dry gas wells. Among new developments perhaps the most significant was the pressure-main-tenance project for the Midway field of Lafayette County, which is utilizing fresh water as the maintenance medium. This is the first fresh-water pressure-maintenance operation during primary production of an oil field in the United States. The operator of the project, Barnsdall Oil Co., estimates that the ultimate recovery of oil from this field will be increased from 32.5 to 65 million barrels. The Midway pool is of the dissolved-gas type, but a similar project is getting underway for the Magnolia field, Columbia County, a pool of the gas-cap and water-drive type. Dual completion of wells, on concurrent production from two productive zones through a single well bore, became common practice in South Arkansas during the year. As the year ended, some 50 wells had been dually completed and it was estimated that the first 37 of these wells represented a saving of more than 2 1/4 million dollars and a saving in steel of 7000 tons. The majority of the wells dually completed were those reaching depths in the neighborhood of 9000 ft. below the surface and initially productive there. Selective completion at lesser depths in the same well bore proved mechanically feasible and economically sound. The year was marked by the successful completion and placing into operation of three large natural-gas desulphurization

Jan 1, 1944

By Alec M. Crowell, J. W. Sanders

While the production of crude oil and condensate in South Arkansas increased only 1.7 per cent over the 1940 figure, complete utilization of gas produced with the oil and condensate, and heretofore wasted, was beginning to be evidenced. There were 26,229,264 bbl. of oil and condensate produced in South Arkansas during 1941, as against 25,790,380 bbl. for the year 1940. (Fig. I.) Since 1936, deep producing sands have been discovered in 18 fields and during that period only 40 per cent of the total state production has come from Upper Cretaceous formations while 60 per cent came from the Lower Cretaceous and Jurassic formations. The gas produced with crude oil and condensate from the latter formation contains large quantities of hydrogen sulphide, the maximum being 6900 grains per 100 cu. ft. in the Patton pool of Lafayette County. Gas Utilization During the latter part of 1940 and the early part of 1941, pilot plants were placed in operation to determine whether the hydrogen sulphide and deleterious material in South Arkansas gases could be removed economically. The Federal Government desired to build a large aluminum plant in the Ouachita Valley and was seeking cheap fuel for the generation of electricity. The fact that the gases were produced with appreciable quantities of crude oil and condensate made it available at a very low price, since the state's conservation law prohibits the flaring of any gas. As a result of these experiments the first large-scale unit for the processing of gases containing hydrogen sulphide was placed in operation on Sept. I, 1941. The plant is in the Magnolia oil field, Columbia County. It processes residue gas from the Shell Oil Company's gasoline plant in that field and also raw gas from the Village field, 6 miles east of the Magnolia field. The gas entering the desulphuri-zation unit is laden with approximately 1400 grains of hydrogen sulphide per 100 cu. ft. and is stripped to a content of 4 grains per 100 cu. ft. The capacity of the plant is 15 million cu. ft. of gas treated daily under a pressure of 160 lb. per sq. in. The cost of treatment, exclusive of depreciation, is appreciably less than I per 1000 cubic feet. Two other plants of much greater capacity have been announced and priorities have been granted, which should bring the total amount of gas treated to 150 million cu. ft. daily. The gas to be treated will have a maximum hydrogen sulphide content of 4500 grains per 100 cu. ft. and will be processed under a pressure of 600 lb. per sq. in. These developments are something entirely new in field practice for the industry. The fact that this heretofore wasted gas is available at very low cost has led to the location of some eight war industries within the state, in addition to the alu-minum plant. Recovery OF Sulphur The Susearch Corporation and the Southern Acid and Sulphur Co. placed in operation during 1941 pilot plants to de-

Jan 1, 1942

By H. M. Cyr, T. F. Steele, C. W. Siller

The development of a new metallurgical roasting device is described. It consists of a refractory column into which air is injected at various levels, forming several superimposed fluidized beds with no supporting grates. When pelleted zinc sulphide concentrates are charged, the roasted product needs no further sintering before reduction to metal. WHEN a gas such as air is blown upward with increasing velocities through a loose mass of solid particles, marked changes in the physical behavior of the particles are noted. At first, when the velocity of the gas is insufficient to support any of the solid, the mass constitutes a "fixed bed." As the gas velocity increases until the pressure drop through the bed approaches the effective weight of the bed per unit area, the bed expands until the solid particles are supported by the air rather than by the lower particles. Some vibration of the particles becomes apparent, but little mixing occurs. This condition is called a "quiescent fluid bed." A further increase in gas velocity imparts more separation and more motion to the individual particles until a condition of turbulence is reached. This "turbulent fluid bed" resembles a rapidly boiling liquid with the characteristic highly agitated diffuse surface and many small eruptions of the boiling mass. Different degrees of turbulence can be generated and all produce excellent mixing. The final stage occurs when the gas velocity becomes so great as to create a "dispersed suspension." Here no surface of the mass is defined and the gas carries solid particles out of their original positions. These changing conditions of fluidization have been studied carefully and pertinent nomenclature standardized by a committee of the American Institute of Chemical Engineers.' Many mathematical analyses2-3 have been made of the forces acting in a fluid bed. These analyses are invaluable, especially for the design of column sizes and selection of equipment. However, in a metallurgical process involving solids of many sizes with changing densities, varying temperatures, and changing gas compositions within the bed, calculations based on theory become approximate. Optimum operating conditions then are best determined experimentally. Many applications have been made of the principles of fluid-bed action by mechanical, chemical, and metallurgical engineers. Especially when good con- tact between reacting solids and gases is desired, very effective results are obtained from fluid beds. They permit excellent temperature control and uniformity throughout a mass of solids in fluid action. Heat transfer to walls and any coolers is high, and fast reaction rates are attained because the solid surfaces are continuously swept clean. The main disadvantages of fluid-bed operations are the danger of short-circuiting in a single bed, danger of incipient sintering which stops action, the necessity of avoiding large changes in particle size or density during roasting, and dust losses when particles of the charge are carried out with exit gases. In the metallurgical field the roasting of sulphide ores to form oxides and sulphur dioxide appears to combine several operating conditions which can be achieved to advantage in a fluid bed. Roasting involves a solid-gas reaction where a high reaction rate is necessary for high capacity, where good temperature control is important in order to prevent sintering, where good heat transfer is needed, and where the density of the solids, when changing from sulphides to oxides, is not largely changed. Short-circuiting, however, constitutes a major problem when a single fluid bed is used. Because of the turbulence of the bed, an entering particle may be in the region of the discharge before it is roasted. Hence, to attain a satisfactorily low sulphur in the calcine, a long average residence time with correspondingly low capacity is required. The solution to this difficulty is the use of multiple stages, which in the conventional fluid-bed design requires separate hearths with feed and discharge mechanisms for each stage. A further practical difficulty in fluid-bed roasting of flotation zinc concentrates is their fine particle size which makes a true fluid action without excessive carry-over of dust very difficult to attain, especially when the large air volumes necessary for high capacity are used. A New Design After considerable experimentation in the laboratory and on a semipilot-plant scale, a new method and equipment for roasting were devised which provided a unique solution to these problems. A detailed account of this development appears in the patent literature," and many of the variations of this development reported herein are the subject of

Jan 1, 1955

By John M. Kelly

New Mexico produced 38,882,342 bbl. of oil in 1943, and regained seventh place among the oil-producing states. This production was an increase of 6,968,526 bbl., or 21.8 per cent, over the figure for 1942. The maximum per-well allowable on Jan. I, 1943, was 38 bbl. daily and at the end of the year this figure had been increased to 48 bbl. Allocations as set by the New Mexico Oil Conservation Commission closely followed recommendations by the Petroleum Administrator for War and the average daily pipe-line runs were 106,476 bbl., being within 2.2 per cent of these allocations. Production for Lea County was 33,043,925 bbl.; Eddy County, 5,405,-967 bbl.; northwestern New Mexico, 432,070 bbl., and Chaves County, 380 barrels. Drilling activity for New Mexico in 1943 was only 75 per cent of that in 1942, with 255 completions. Of these completions 180 were oil wells, 10 gas wells and 65 dry holes. The ratio of dry holes to producers, more than I to 3, was the greatest in recent years. Of these dry holes, 46 were drilled within the boundaries of proven . areas while 19 were wildcats. Wildcat drilling during 1943 was responsible for the discovery of four new oil fields and one new gas field, as well as three extensions to existing proration areas. At the close of the year the New Mexico Oil Conservation Commission had designated 64 areas as proven for oil and/or gas. The Monument area was again New Mexico's largest producing oil field, with an annual production of 7,228,855 bbl. Next was Eunice, with 6,461,044 bbl., followed by Vacuum with 4,946,110 bbl. IIobbs, ranking fourth, with 3,799,114 bbl., was the leader in total recovery with an accumulated production of 104,180,53I bbl., or more than 10,000 bbl. per acre to date. Drilling activity in Lea County accounted for completion of 67 oil wells, 2 gas wells and 24 dry holes. One of these oil wells was the discovery well of a new area and three extended proven areas. The most active drilling campaign in the county was again in the Maljamar area, where 18 oil wells were completed. The Maljamar Cooperative Repressuring Agreement affected 141 producing wells, and operations were a decided success, more than 85 per cent of the gas produced being returned to formation. The new oil field for Lea County was designated as the San Simon area although boundaries have not been established to date. Discovery well for this area was the Skelly Oil Company's State U. No. I, in theNE. NE. K of sec. 5, T.22 S.,R.ssE. This well was drilled to a total depth of 4183 ft. and plugged back to 4138 ft. after encountering bottom-hole water. Initial production was 124 bbl. per day on the pump. This oil is 37.4' gravity and has a sulphur content of I per cent. Productian is from Yates sand of Permian age. The Lynn area of southern Lea cbunty was extended 145 miles to the northwest

Jan 1, 1944

By John M. Kelly

New Mexico produced 38,882,342 bbl. of oil in 1943, and regained seventh place among the oil-producing states. This production was an increase of 6,968,526 bbl., or 21.8 per cent, over the figure for 1942. The maximum per-well allowable on Jan. I, 1943, was 38 bbl. daily and at the end of the year this figure had been increased to 48 bbl. Allocations as set by the New Mexico Oil Conservation Commission closely followed recommendations by the Petroleum Administrator for War and the average daily pipe-line runs were 106,476 bbl., being within 2.2 per cent of these allocations. Production for Lea County was 33,043,925 bbl.; Eddy County, 5,405,-967 bbl.; northwestern New Mexico, 432,070 bbl., and Chaves County, 380 barrels. Drilling activity for New Mexico in 1943 was only 75 per cent of that in 1942, with 255 completions. Of these completions 180 were oil wells, 10 gas wells and 65 dry holes. The ratio of dry holes to producers, more than I to 3, was the greatest in recent years. Of these dry holes, 46 were drilled within the boundaries of proven . areas while 19 were wildcats. Wildcat drilling during 1943 was responsible for the discovery of four new oil fields and one new gas field, as well as three extensions to existing proration areas. At the close of the year the New Mexico Oil Conservation Commission had designated 64 areas as proven for oil and/or gas. The Monument area was again New Mexico's largest producing oil field, with an annual production of 7,228,855 bbl. Next was Eunice, with 6,461,044 bbl., followed by Vacuum with 4,946,110 bbl. IIobbs, ranking fourth, with 3,799,114 bbl., was the leader in total recovery with an accumulated production of 104,180,53I bbl., or more than 10,000 bbl. per acre to date. Drilling activity in Lea County accounted for completion of 67 oil wells, 2 gas wells and 24 dry holes. One of these oil wells was the discovery well of a new area and three extended proven areas. The most active drilling campaign in the county was again in the Maljamar area, where 18 oil wells were completed. The Maljamar Cooperative Repressuring Agreement affected 141 producing wells, and operations were a decided success, more than 85 per cent of the gas produced being returned to formation. The new oil field for Lea County was designated as the San Simon area although boundaries have not been established to date. Discovery well for this area was the Skelly Oil Company's State U. No. I, in theNE. NE. K of sec. 5, T.22 S.,R.ssE. This well was drilled to a total depth of 4183 ft. and plugged back to 4138 ft. after encountering bottom-hole water. Initial production was 124 bbl. per day on the pump. This oil is 37.4' gravity and has a sulphur content of I per cent. Productian is from Yates sand of Permian age. The Lynn area of southern Lea cbunty was extended 145 miles to the northwest

Jan 1, 1944

By Axel Sahlin

Having no business interest in any of the various machines used for granulating ores, my remarks on the subject are prompted solely by my desire to contribute towards the determination of the best apparatus such information, as I have been able to gather,

Jan 1, 1893

By G. D. Just

INTRODUCTION Large scale underground mining involves the bulk handling of fragmented material. The cost and efficiency of the mining systems is there- fore significantly influenced by material flow characteristics. Flow problems may occur in the form of ore pass blockages which interrupt the free flow at extraction openings. The costs of such delays can be readily assessed and compared to the costs incurred in reducing blockages by improved fragmentation or larger ore passes. In practice the problem is more complex than this statement suggests because it is generally un- economic to design for zero ore blockages. Another major flow problem occurs in the form of relative movement of ore and waste as the fragmented material is extracted. This produces waste dilution in the recovered ore and influences total ore recovery. This flow problem is much more complex than the ore block- age phenomena. Many questions concerning the precise flow characteristics remain unanswered because of the variability of size distributions, particle shapes, material properties and the total extraction layout and design. Model studies can provide a visual and quantitative illustration of probable flow characteristics but full scale data collection is necessary to evaluate the precision of such information. The methods and types of data obtained must be carefully selected to recover the maximum volume of useful information for operational control and future design. It is essential that honest precision levels are assigned to the data and any subsequent analyses. Grade control data may give misleading short term information on flow characteristics because of the difficulty in knowing the true grade of the mass of material before extraction commences. However, in the long term control of extraction grades is vital to the profitable operation of the mining system. The most efficient extraction design and operational schedule can only be determined after all of the facts and variables are known. This is usually only possible after the orebody has been completely extracted. However, if design and operational personnel have a full appreciation of the nature and variability of material flow under different conditions the best possible results should be achieved. The most significant features of material flow are out- lined in this paper in order to provide mine planning and mine management personnel with some of the necessary information relating to material flow. Available facts and reliable figures from selected publications are noted in association with unbiased and hopefully accurate opinions of the relevance of the data to mine design and mine system control. Possible future developments and profitable areas for research into material flow problems are also detailed. MATERIAL FLOW AND MINING METHODS The effects of material flow on the design and operation of an integrated underground ore handling system is one factor which is common to most mining methods. Analysis of the system as detailed by Just, 1980, permits the identification of unit process objectives. For example, a typical underground ore handling system as illustrated in Figure 1, involves the following unit operations:- (i) Gravity flow of ore in stope (ii) Ore extraction at base of stope (iii) Ore haulage on the production level (iv) Dumping of ore into ore pass system (v) Gravity flow of ore in the ore pass (vi) Underground crushing of ore (vii) Haulage of crushed ore to shaft (viii) Hoisting of ore to the surface. Average flow rates in each of these unit operations can be misleading due to variability in incremental capacity caused by flow blockages and machine delays. Thus to effectively analyse the probable performance of the system, it is necessary to have a measure of the flow loading and haulage rate variability. Mechanical equipment performance specifications can be used to provide such information for loading, haulage and crushing; however, in the case of the gravity flow of material field measurements are required to relate the probability of "hang-ups" to the degree of fragmentation. Factors affecting the frequency of flow stoppages are, size, distribution and cohesiveness of broken material and the geometry and size of the flow channel. Ore pass channel design is relatively simple since regular cross-sectional shapes are used

Jan 1, 1981

By William H. Spice

For the year 1943, exploratory drilling in South Central Texas continued on the sharp decline that started during 1942. Of the 3 counties comprising this district, as now revised to include the same area as is covered by District No. I, Oil and Gas Division, Railroad Commission of Texas, I5 counties are producing oil or gas. Only 29 exploratory wells were drilled during 1943, as compared with 51 exploratory wells in 1942, or a decrease of over 40 per cent. One new oil field and one new gas field were discovered during the year and a new horizon was discovered in an existing oil field. This cornpares with two new oil fields and an extension to an existing gas field in 1942. The one new oil field, South Washburn, in southeastern La Salle County, was discovered by Quintana Petroleum Corporation's No. I-D South Texas indicate in April 1943, flowing 4 bbl. per day, 48" A.P.I. gravity oil with an estimated 4 million cubic feet of gas from Wilcox sand at 6030 ft. This well i's the result of an extensive seismograph survey of the area. It is about 434 miles southwest of the same company's Green Branch field and by the end of the year one dry hole had been drilled to the southwest of this discovery. The one new gas field, which was not named, was located in eastern McMullen County by Edwin M. Jones' No. 102 Ezzell, in November 1943, for an estimated 8 million cubic feet of gas from shallow Jackson sand at 1222 ft. NO addi- tional wells have been drilled in this area, which may also be considered as an extension to the South Calliham field. The one new producing horizon was discovered in the South Campana field in southeastern McMullen County, by Argo Oil Corporation's No. 2-G Edrington, in January 1943, flowing 55 bbl. per day, 21' A.P.I. gravity oil with 40 per cent water from Government wells sand at 2609 feet. None of these discoveries were of major importance and subsequent development in these new areas has proved to be disappointing. Produc'tion for the district during 1943 totaled approximately 6,985,000 bbl. from about 3430 producing wells. This is an increase in production of about 5 per cent over 1942, but a decrease in producing wells of about 10 per cent under the number of wells producing in 1942 for the same district. Average production per well was 5.4 bbl. during 1943 as against 4.8 bbl. during 1942. Approximately 5,320,000 hhl. of this total production, or 76 per cent, was produced by the four Edwards lime fields, Luling, Branyon, Salt Flat, and Darst Creek, which are from 22 to 14 years old. The remaining production came from the 43 other active oil fields in the district. Drilling in the proven fields maintained approximately the same level as for 1942, with a total of 36 wells drilled. Of these operations, 21 were oil wells, one was a gas well and 14 were dry holes. This is a slightly better proportion of producers than for 1942. Washburn field had the greatest number of new producing wells drilled during the year, with a total of 10.

Jan 1, 1944

By William H. Spice

For the year 1943, exploratory drilling in South Central Texas continued on the sharp decline that started during 1942. Of the 3 counties comprising this district, as now revised to include the same area as is covered by District No. I, Oil and Gas Division, Railroad Commission of Texas, I5 counties are producing oil or gas. Only 29 exploratory wells were drilled during 1943, as compared with 51 exploratory wells in 1942, or a decrease of over 40 per cent. One new oil field and one new gas field were discovered during the year and a new horizon was discovered in an existing oil field. This cornpares with two new oil fields and an extension to an existing gas field in 1942. The one new oil field, South Washburn, in southeastern La Salle County, was discovered by Quintana Petroleum Corporation's No. I-D South Texas indicate in April 1943, flowing 4 bbl. per day, 48" A.P.I. gravity oil with an estimated 4 million cubic feet of gas from Wilcox sand at 6030 ft. This well i's the result of an extensive seismograph survey of the area. It is about 434 miles southwest of the same company's Green Branch field and by the end of the year one dry hole had been drilled to the southwest of this discovery. The one new gas field, which was not named, was located in eastern McMullen County by Edwin M. Jones' No. 102 Ezzell, in November 1943, for an estimated 8 million cubic feet of gas from shallow Jackson sand at 1222 ft. NO addi- tional wells have been drilled in this area, which may also be considered as an extension to the South Calliham field. The one new producing horizon was discovered in the South Campana field in southeastern McMullen County, by Argo Oil Corporation's No. 2-G Edrington, in January 1943, flowing 55 bbl. per day, 21' A.P.I. gravity oil with 40 per cent water from Government wells sand at 2609 feet. None of these discoveries were of major importance and subsequent development in these new areas has proved to be disappointing. Produc'tion for the district during 1943 totaled approximately 6,985,000 bbl. from about 3430 producing wells. This is an increase in production of about 5 per cent over 1942, but a decrease in producing wells of about 10 per cent under the number of wells producing in 1942 for the same district. Average production per well was 5.4 bbl. during 1943 as against 4.8 bbl. during 1942. Approximately 5,320,000 hhl. of this total production, or 76 per cent, was produced by the four Edwards lime fields, Luling, Branyon, Salt Flat, and Darst Creek, which are from 22 to 14 years old. The remaining production came from the 43 other active oil fields in the district. Drilling in the proven fields maintained approximately the same level as for 1942, with a total of 36 wells drilled. Of these operations, 21 were oil wells, one was a gas well and 14 were dry holes. This is a slightly better proportion of producers than for 1942. Washburn field had the greatest number of new producing wells drilled during the year, with a total of 10.

Jan 1, 1944

By R. Laird Auchmuty

FOREWORD THE A. I. M. E. Subcommittee on Bituminous Mining has been trying for several years to secure the information that was collected by the Marquette Cement Manufacturing Co. on the subsidence of its property caused by mining coal beneath it. The Marquette company was willing to have these data used, but it was impossible to obtain them because the records had been filed away. About two years ago these records became available and the engineering data presented herewith were compiled from them by R. L. Auchmuty, assisted by L. E. Young, who was connected with the collection of the information. On account of the cost, it is impossible to reproduce all of the data here, although the original information is on file with the records of the Committee on Ground Movement and Subsidence. The accompanying charts show representative and average data and give only the engineering information with enough description to tell how it was obtained. It is hoped that all of those connected with the original case will participate in the discussion that this will bring forth. HOWARD N. EAVENSON, Chairman, Subcommittee on Bituminous Coal Mining.

Jan 1, 1931

By STEPHEN L. GOODALE

THE question indicated in this title was put by letter to a number of my friends working in various industries, who have charge of young metallurgical graduates. The replies were almost unanimous in stating that the college training should cover in the most .thorough manner possible those sciences which are the fundamentals - of engineering. Mathematics, physics, mechanics, electricity, chemistry, physical chemistry, and their applications to actual problems of life were mentioned in most of the letters I received. Some writers added also business law, economics,. and finance. One reply expressed it: "These subjects, well founded, mixed with good judgment, well applied, should enable the .young man to carry on the art of life successfully." One answer stated frankly what is really wanted: "As much as possible.' ' This writer mentioned .the sciences as being very important, but he wishes men ' to be trained in metallurgy also, and he concedes the omission of some advanced chemistry and physic's to secure the metallurgy. He emphasized particularly. the a we. desirability of work in college to development' He concludes his letter with a repetition of his slogan that what is wanted is as much as is possible.

Jan 1, 1930

By C. C. Hawes

SILICA is the main impurity in iron ore. It is intimately associated with the iron oxide, sometimes free but more often in the combined state, as a mineral silicate. Its separation and purification sometimes present difficult problems to the analyst. In the absence of any definite knowledge to the contrary, orthosilicic acid. H4SiO4, is supposed to be the only silicic acid made, all other forms, such as metasilicic acid, H2SiO3, representing different degrees of its dehydration. These acids are exceedingly weak but form the most stable compounds found in nature. They are known as the silicate minerals and are formed by the combination of the different metallic oxides

Jan 1, 1936

By WILLARD HAYES

(Glen Summit Meeting, June, 1911.) THE determination of the question whether the Mayari and Moa mining-claims of the Spanish-American Iron Co. have been rightly denounced under the third section of the law of bases rests on the findings in the following questions of fact: 1. Is the mineral an iron-ore? 2. Is the iron-ore a bog iron-ore? 3. Is the iron-ore ocher? 4. If ocher is present, can it be mined separately and independently of the iron-ore ? 1. IS THE MINERAL AN IRON-ORE? Since the material is shown by a large number of analyses to contain from 41. to 50 per cent. of metallic iron and less than 0.02 per cent. of phosphorus, and since it has been and is being actually used on a commercial scale for the production of iron and steel, it must be classed as an iron-ore. 2. IS THE IRON-ORE A BOG IRON-ORE? Bog iron-ore has certain invariable characteristics of chemical composition, physical appearance, geological relations, and origin by which it can always be recognized with certainty. In chemical composition, it is the hydrated sesquioxide of iron, limonite, or a mixture of limonite and other closely-related iron hydrates. It never contains the anhydrous oxides-hematite or magnetite; is never magnetic, and never contains either nickel, chromium, or cobalt oxides. On the other hand, it is invariably high in phosphorus-content. In physical appearance and texture it is a yellow or reddish-brown amorphous spongy material, and always contains water-worn sand-grains, silt, clay, and plant-remains. In its geological relations it is wholly independent of the rock

Mar 1, 1911

By ABBOT A. HANKS

WHEN gold was discovered in California, and San Francisco grew almost over night from a handful of people to many thousands, one of the first difficulties experienced was the lack of money. Gold dust in considerable quantities was rushed into the city from the various mining camps but there was no money. Purchases were paid for by weighing out dust in hand scales. We can appreciate' the difficulty of paying for a drink or buying a postage stamp under these conditions. All this gold was in the form of dust from placer workings and the first metallurgists were the assayers' who melted and refined this gold, casting it into bars which were weighed, assayed, stamped with fineness; value, and the name of the assayer. Many .of these plants were of considerable size, handling shipments that were accumulated by banks and express companies throughout the "Diggings" and sent to San Francisco to be shipped by water to the eastern states. Several

Jan 1, 1931

By O. C. Baptist

The Umiat oil field is in Naval Petroleum Reserve No. 4 between the Brooks Range and Arctic Ocean in far-northern Alaska. The Umiat anticline has been tested by 11 wells, six of which produced oil ; however, [lie productive capacity and recoverable reserves of the field are subject to considerable speculation because of unusual reservoir conditions and because several wells appear to have been .seriously damaged during drilling and completion. Oil is produced at depths of 275 to 1,100 ft; the depth to the bottom of the permanently frozen zone varies from about 800 to 1,100 ft, .so that most of the oil reserves are in the permafrost Reservoir pressures are estimated to range from 50 to 350 psi, increasing with depth, and the small amount of gas dissolved in the oil is the major source of energy for production. Laboratory tests were made on cores under simulated permafrost conditions to estimate oil recoverable by solution-gas expansion from low saturation pressures. The cores were also tested for clay content and susceptibility to productivity impaiment by swelling clays and increased water. content if exposed to fresh water. The results indicate that oil can be produced fronz reservoir rocks in the permafrost and that substantial amounts of oil can be produced from depletion-drive reservoirs by a pre.s.r~lrr drop of as little as 100 psi below the saturation pressure. Freezing of formation water reduces oil productivity much more than that due to increased oil viscosity: Failure of we1ls drilled with rtuter-base mud to produce is attributed to freezing of water in the urea immediately surrounding the wellbore. Swelling clays apparently contributed very little to the plugging of the wells. INTRODUCTION Naval Petroleum Reserve No. 4 lies between the Brooks Range and the Arctic Ocean in northern Alaska. The Umiat oil field is located in the southeastern part of the Reserve and is about 180 miles southeast of Point Barrow (the only permanent settlement in the Reserve and the primary supply point for drilling of the wells at Umiat). Eleven wells were drilled for the U. S. Department of the Navy, Office of Naval Petroleum and Oil Shale Reserves, between 1944 and 1953 to test the oil and gas possibilities of the Umiat anticline. Six of these wells produced oil in varying quantities and the best one pumped about 400 B/D.' Estimates of recoverable oil range from 30 to 100 million bbl. The main oil-producing zones are two marine sandstone beds in the Grandstand formation of Cretaceous age: these are referred to as the upper and lower sands. Good oil shows were found throughout the sand settions in the first three wells drilled on the structure, but the highest rate of oil production obtained on any 01 the many tests was about 24 BOPD. These first wells were drilled with conventional rotary methods using water-base mud; later wells were drilled either with cablc tools using brine or rotary tools using oil or oil-base mud. These experiments were successful as is shown by comparing the oil production from Well No. 2 with that from No. 5. These two wells are only 200 ft apart and are located at about the same elevation on the structure. Well No. 2. drilled with a rotary rig using water-base mud, was abandoned as a dry hole after all formation tests were negative. Well No. 5. drilled with cable tools and reamed with a rotary using oil, pumped 400 BOPD which was the maximum capacity of the pump and less than the capacity of the well. These field results indicated that the producing sands were extremely "water sensitive" and it was assumed that the cause of this sensitivity was the presence of swelling clays in the sands. Because of the very unusual reservoir conditions and the difficulties encountered in completing oil wells in the permafrost. the Navy asked the U. S. Bureau of Mines to make laboratory studies under simulated permafrost conditions to assist them in estimating the production potential of the field and the recoverable reserves. These tests were designed to determine the cause of the plugging of wells in the permafrost and to test oil recovery from frozen sand by solution-gas expansion with the oil gas-saturated at very low pressures. EXPERIMENTAL METHODS AND PROCEDURES Samples Analyzed Core samples were analyzed that represent the lower sand in Umiat Well No. 7, the upper sand in No. 3. and both the upper and lower sands in No. 9. These sands should be productive in all of the wells because of their location on the structure. Core samples from

By T. M. Girdler

INDUSTRIAL progress and development in this country from the earliest daps to the present has proceeded at an ever-quickening pace. Yet during recent decades the nature of our industrial progress and development has undergone a change of great significance. The earlier days were a period of tremendous expansion. Population was increasing by leaps and bounds. Vast areas of new land were being .2 opened to settlement. And almost boundless new sources of timber, coal, oil, ores, and power were being opened to ever-expanding markets. Today, however, that picture has al- most completely changed. Today, with population increase tapered way off and the opportunity for free expansion into western frontiers gone, the great industrial development of our country continues on a vastly different front. Industrial progress and development today rest on a foundation of technology. The key- stone is research. Our frontiers to- day are frontiers of sciencec

Jan 1, 1939