Search Documents

By K. L. Komarek, P. F. J. Landler

Synthetic polycrystals of wustite were reduced ilz H2-H2O mixtures over limited roncentration ranges wiltun the wustite. field and the weight changes were continuously followed with a McBain quartz spiral balance. The reduction was. found to be controlled by a combined surface plus solid-state diffusion reaction. The solid-state diffusion had an activation energy of 38 kcal. Self--diflusioities of iron decreased with itzcreasing vacancy concentration. The activation energy of. the surface reaction runs different tor- different samples. The surface reaction-rate constan increased with increasirzg vacancy concentration. THE reduction of the oxides of iron has been studied for many years. Edstroem' has summarized the early work and has provided much information on the reduction of magnetite and hematite by hydrogen and carbon monoxide. More recent summaries are those by smeltzer2 and Themelis and Gauvin.3 Most investigators have reported that the iron metal which forms the outer layer during gaseous reduction is rather porous. According to Kohl and Engel14 the formation of such a porous iron layer depends on the properties of the underlying wiistite layer, on the reaction of the gas with the wustite surface, and on the transport of matter through the wustite layer. McKewan, Quets, Wadsworth, and Lewis, and Knacke 10 have found that, if a porous iron layer is formed, a surface reaction between gas and wustite at the bottom of the pores controls the rate of reaction. Seth and ROSS 11 and Warner 12 have pointed out that the influence of the gaseous pore diffusion through the porous iron layer cannot be neglected. It has further been shown that the wiistite layer formed during reduction is dense and that transport of matter across the layer occurs only by solid-state diffusion of iron ions.13,14 The solid-state diffusion rates observed by Edstroem and Bitsianis 14 and the surface reaction rates observed by Quets eta1.' show that an interaction of the two steps in controlling the reaction rate has to be considered. In this investigation the reduction of wustite was studied with respect to the interaction of the two steps, isolated from any other effects, by reducing wustite within the wustite field from higher to lower oxygen concentrations with H2-H2O gas mixtures. A similar study with CO-CO2 mixtures has been performed by Levin and wagner.15 Fused synthetic wustite polycrystals were reduced in steps of 0.4 wt pct from 24.4 to 23.2 wt pct 0 and over a temperature range from 700" to 1050°C. A few tests were also conducted with reduction steps from 24.4 to 23.6 wt pct 0 and 24.5 to 23.2 wtpct0. The Fe-O phase diagram is shown in Fig. 1 where the composition of the gas phase in equilibrium with the condensed phases is plotted as pct H2 vs the temperature. A careful study of the literature led to the conclusion that the fully drawn equicomposition curves (in wt pct O) in the wustite field used by Edstroem 1,16 and other authors needed some correction. Based on results by Darken and Gurry17 (shown as open circles) and on some of our own data, four corrected curves for 23.2, 23.6, 24.0, and 24.4 wt pct O were calculated (drawn as dashed lines in Fig. 1) which should replace the fully drawn equicomposition curves. MATERIALS AND APPARATUS Materials and Specimen Preparation. Wustite was prepared from iron sulfate (Fisher Scientific Co., New York) which had a purity of over 99.92 pct, with small amounts of manganese, copper, and zinc adding up to 0.03 pct. From the aqueous solution iron oxalate was precipitated and decomposed to magnetite according to Economos. 18 The magnetite powder was pressed into cylinders and sintered in vacuum at 900°C for several hours. The sintered compacts were placed in a platinum crucible of 2.5 cm diam which was fitted into a high-purity alumina crucible and then inserted into the center of the graphite heating element of an electric resistance furnace.lg The furnace was evacuated to below 1 p Hg and the magnetite sample was slowly heated. The evolution of gases during heating deter-

Jan 1, 1967

By J. Wes Blakely

In the mid-1950s the importation of foreign oil began to encroach on traditional coal markets such as railroad steam engine fuel, home heating, electrical generating plants, and others. Many of the smaller coal companies with substantial coal reserves subsequently found that they could no longer continue to mine economically and merged in various ways with larger established coal mining concerns. As the seats of top management and authority were removed from the mines to large metro centers such as New York, Pittsburgh, and Chicago, the more personal relationship between mine workers and management that had existed prior to these mergers began to be eroded and replaced by "remote control" mine management. The disappearance of this face-to-face contact of upper management with mine employees tended to create barriers blocking simple effective communications between coal mine management and labor. In examining the human relations aspects of the coal mining industry, many elements, some concerned with work and others not, have depicted the industry as almost devoid of good applied human relations and communications practices, and, in truth, little has been done to alleviate this situation. In past years many coal producing companies, with the exception of one of the largest, failed to adequately define the term "communications ' as it applied to their companies, whether internally or externally. Internally many still place heavy reliance on written communications such as company-wide newspapers to do the job of communicating with their employees which they feel ought to be done. One company puts an inordinate belief in its company "newspaper" as the primary instrument to stimulate its work force into increasing productivity. Primarily aimed at the workers, who greatly outnumber the salaried administrative people, this publication mainly documents the fortunes of individual mine workers who are felt to have achieved something with their lives, e.g., a mine worker who had managed to put four children through universities, the

Jan 1, 1981

By J. Wes Blakely

In the mid-1950s the importation of foreign oil began to encroach on traditional coal markets such as railroad steam engine fuel, home heating, electrical generating plants, and others. Many of the smaller coal companies with substantial coal reserves subsequently found that they could no longer continue to mine economically and merged in various ways with larger established coal mining concerns. As the seats of top management and authority were removed from the mines to large metro centers such as New York, Pittsburgh, and Chicago, the more personal relationship between mine workers and management that had existed prior to these mergers began to be eroded and replaced by 'remote control mine management. The disappearance of this face-to-face contact of upper management with mine employees tended to create barriers blocking simple effective communications between coal mine management and labor. In examining the human relations aspects of the coal mining industry, many elements, some concerned with work and others not, have depicted the industry as almost devoid of good applied human relations and communications practices, and, in truth, little has been done to alleviate this situation . In past years many coal producing companies, with the exception of one of the largest, failed to adequately define the term “communications” as it applied to their companies, whether internally or externally. Internally many still place heavy reliance on written communications such as company-wide newspapers to do the job of communicating with their employees which they feel ought to be done. One company puts an inordinate belief in its company "newspaper" as the primary instrument to stimulate its work force into increasing productivity. Primarily aimed at the workers, who greatly outnumber the salaried administrative people, this publication mainly documents the fortunes of individual mine workers who are felt to have achieved something with their lives, e.g., a mine worker who had managed to put four children through universities, the

Jan 1, 1981

By P. Barnes

In vol.33 of the Proceedings of the Institution of Civil Engineers, London (part 2, for 1870-71), may be found a statement of the cost of two blast furnaces, together with a somewhat detailed description. The attempt will he made in this note to restate these items of cost, so that the information may be rendered perhaps more accessible to our members than in its present place of record, and also in order that the items may be more intelligibly compared among themselves, or with similar items in other cases.

Jan 1, 1879

By M. E. Lombardi

ThE Coalinga oil field is located on the west side of the San Joaquin Valley, California. The structure is in general a monocline, the edges of the oil horizon resting on the foot hills and dipping gently toward the east. One prominent anticline occurs plunging southeast. The earlier drilling was done in the foot hills comparatively near the outcrop and the wells were shallow. The sands were followed eastward and, in the case of the anticline, along the plunge, the wells becoming deeper and deeper until the depth of 4,000 ft. was reached and passed. There is nothing to show that the oil will not be found in quantity at still greater depth. In fact, some of the best producers have tapped the sand at close to 4,000 ft. The recovery of oil still farther to the east, and therefore at greater depth, seems to be mainly a question of drilling. In this territory the formations drilled through are chiefly sands and shales; they will not "stand up" in an open drilling hole; the casing has to be carried close to the bit, and it is always difficult to keep the casing free for any considerable distance. Ability to carry casing of comparatively large diameter without conductor pipes for distances of 2,000 or 3,000 ft. or over is desirable in such territory chiefly for two reasons. It makes it possible to enter the oil sand with a pipe of ample diameter; it eliminates one or more expensive strings of casing which act only as conductors for the water string, and furthermore, in territory where waters are encountered which corrode steel rapidly, it makes possible the construction of a rust- and alkali-resisting water string. It is always desirable to shut off top waters, which may lie within 100 ft. or less of the oil sand, with 10-in. pipe. Where the depth is so great that a practical weight of 10-in. pipe will not withstand the probable collapsing pressures, 81/4 in. at least is desirable. About the limit of rotary drilling to date in California seems to be the setting of the 10-in. string at 3,200 ft., although the rapid advance in rotary work during the past year seems to indicate that this depth may soon be increased. It is my purpose now, however, to treat only of cable-tool drilling. The problem is to reach a depth of 4,000 ft. or more with a string of

Jan 1, 1915

POSITIONS VACANT No. 255. A company manufacturing malleable iron fittings in Connecticut needs a manager for its steel department. Experience with converter is essential. No. 256. A prominent mining company in Central America wishes a shift boss for its mill and cyanide plant, who is technically trained, experienced, and can speak Spanish. He should he sufficiently expert to be able to take entire charge of the mill in case of emergency. Salary $150 per month on a two years' contract, with additional allowance for board, lodging and transportation expenses. No. 257. A Mexican copper mining company in the State of Puebla needs an engineer on surveying and mapping and drafting in connection with field construction. Healthy locality. Salary $150 per month.

Jan 1, 1918

By Robert Glass Cleland

THE DEVELOPMENT of the Phelps Dodge copper and railroad interests began in one era of the company's history and continued unbroken into the next. Yet the two eras themselves were strikingly dissimilar and represented marked differences in the company's activities, corporate structure, and personnel. From its organization in 1834 almost to the end of the first decade of the twentieth century, the partnership known as Phelps Dodge was directed, managed, and controlled by the family dynasty established by Anson Greene Phelps. The last two directing partners of this three-generation-old regime assumed control of the company's affairs in 1879 when the economic revolution that followed the Civil War was well under way.' They lived in an age of gigantic undertakings, gigantic enterprises, gigantic combinations, gi- .

Jan 1, 1952

Balancing the prodigious iron ore deposits of Western Australia are the equally vast coal resources of the Bowen series of eastern Queensland. The Bowen series is a Permian basin stretching 500 miles in a north-south line. The beginning of what will be large scale mining of the Kianga-Moura coalfields in Dawson Valley was made by the Australian company of Thiess Bros. in July 1961. Then Peabody Coal Co. of St. Louis, Mo., joined Thiess. Later, Mitsui & Co. Ltd. received a 20% interest in the firm Thiess, Peabody, Mitsui Coal Pty. Ltd. Rtitsui was to lend the company money for development. Queensland Parliament, by special act, granted the company exclusive franchise over the Kianga-Moura coalfield, an area of 350 square miles. The rights do not include other minerals. The company is to have a 120-mile railroad completed to Gladstone or some other port in seven years. It must produce at least 500,000 long tons of coal annually until the line is built, after which production is to be upped to 2 million tons. By December 1962, these arrangements were completed.

Jan 10, 1964

By Robert R. Walden, LeMont West

K ENTUCKY'S first acid-grade fluorspar flotation Kmill, shown in Fig. 1, was placed in operation Aug. 1, 1952, by the Pennsylvania Salt Manufacturing Co. at Mexico, Ky. During 1951 a critical shortage of acid-grade fluorspar developed and it became necessary for the company to produce part of its fluorspar requirements. In 1951 the company purchased the Crider and Lennen metallurgical fluorspar mill and an adjacent stockpile of tailing at Mexico, Ky. The tailing, assaying about 26 pct calcium fluoride, originated from log washer and jig mill concentrators in the area. As the mill did not have a fluorspar dryer or convenient rail facilities, the company leased the Burleson concentrator at Marion, Ky., where these facilities were available. At Marion, Ky., on the Illinois Central Railroad, dry acid-grade fluorspar is transported direct to the company's Calvert City, Ky., hydrofluoric acid plant. The Mexico flotation plant was reconditioned and designed to produce acid-grade fluorspar from the jig tailing stockpile. The new plant flowsheet is shown in Fig. 2. The ore feed, old tailing, which contains 10 pct of waste rock and coarse gravel assaying approximately 8 pct CaF,, is bound together by sticky clay

Jan 1, 1955

By George M. Rigg, Samuel M. Cassidy

During 1937 a program was begun to mechanize and modernize the then 28-year old Isabella mine of the Weirton Coal Co., which is on the Monongahela River, in Fayette County, Pennsylvania, at one edge of what is generally known as the Coke Region. Weirton Coal Co. is a subsidiary of the National Steel Corporation, and produces metallurgical grade coking coal for the Weirton Steel Co., Weirton, W. Va. Improvements subsequently made included a cleaning plant for washing the entire mine output, shovel-action track-mounted machines for mechanically loading all the coal, universal-type track-mounted cutting and shearing machines, post drills, 8-wheel mine cars of 10 tons capacity, cable-reel gathering locomotives and other auxiliary equipment. This paper presents the factors, reasons and results of decided changes from the mining system generally prevailing in the region, as well as abandonment of selective mining practices in favor of complete seam extraction. Coal-seam Conditions Fig. 1 illustrates the Pittsburgh coal seam on the property. Cover over the seam averages 450 ft., and 675 ft. is the maxi- mum. Main roof varies from very weak to medium strong; usually it disintegrates rapidly on exposure to air. The "wild" coal makes a fairly strong immediate roof if supported by crossbars and if unbroken affords a seal to the main roof. The draw slate is very weak and treacherous. The floor is characterized by numerous irregular bottom rolls, or "horsebacks," protruding from a few inches up to 3 ft. into the coal. Some are soft, but many are hard and flintlike. Although the bottom slate usually is hard, the underlying fire clay causes it to buckle and heave readily with any moderate increase in roof pressure or where damp. As a whole, the bottom is weaker than the main roof. The coal is characterized by numerous closely jointed face and butt cleats and a woody, springy nature when shot, both having a decided influence on face practices. As shown in Fig. I, at both the top and bottom of the main coal seam is a layer of coal of higher ash and sulphur content than the body of coal in the middle. Factors That Influence the Mining System Equipment was bought and organization for mechanical loading was made on the basis of working each mechanical unit as near its full capacity as possible, to lessen investment cost and obtain best operating efficiency. This led to combination double and triple-shift operation at the start, and, very shortly, to all sections being triple shifted.

Jan 1, 1947

By Samuel M. Cassidy, George M. Rigg

During 1937 a program was begun to mechanize and modernize the then 28-year old Isabella mine of the Weirton Coal Co., which is on the Monongahela River, in Fayette County, Pennsylvania, at one edge of what is generally known as the Coke Region. Weirton Coal Co. is a subsidiary of the National Steel Corporation, and produces metallurgical grade coking coal for the Weirton Steel Co., Weirton, W. Va. Improvements subsequently made included a cleaning plant for washing the entire mine output, shovel-action track-mounted machines for mechanically loading all the coal, universal-type track-mounted cutting and shearing machines, post drills, 8-wheel mine cars of 10 tons capacity, cable-reel gathering locomotives and other auxiliary equipment. This paper presents the factors, reasons and results of decided changes from the mining system generally prevailing in the region, as well as abandonment of selective mining practices in favor of complete seam extraction. Coal-seam Conditions Fig. 1 illustrates the Pittsburgh coal seam on the property. Cover over the seam averages 450 ft., and 675 ft. is the maxi- mum. Main roof varies from very weak to medium strong; usually it disintegrates rapidly on exposure to air. The "wild" coal makes a fairly strong immediate roof if supported by crossbars and if unbroken affords a seal to the main roof. The draw slate is very weak and treacherous. The floor is characterized by numerous irregular bottom rolls, or "horsebacks," protruding from a few inches up to 3 ft. into the coal. Some are soft, but many are hard and flintlike. Although the bottom slate usually is hard, the underlying fire clay causes it to buckle and heave readily with any moderate increase in roof pressure or where damp. As a whole, the bottom is weaker than the main roof. The coal is characterized by numerous closely jointed face and butt cleats and a woody, springy nature when shot, both having a decided influence on face practices. As shown in Fig. I, at both the top and bottom of the main coal seam is a layer of coal of higher ash and sulphur content than the body of coal in the middle. Factors That Influence the Mining System Equipment was bought and organization for mechanical loading was made on the basis of working each mechanical unit as near its full capacity as possible, to lessen investment cost and obtain best operating efficiency. This led to combination double and triple-shift operation at the start, and, very shortly, to all sections being triple shifted.

Jan 1, 1947

By Alan M. Bateman

Before World War II we proudly considered that we were the nation of all the world most richly endowed in mineral resources. We knew it was no accident that those countries abundantly supplied with mineral resources became the great manufacturing nations, and the politically and militarily strong ones; and that our own great industrial cities sprang up where coal and iron met. We all reallized, especially we of the mining profession, that the energy of fuels and the solidity of metals spelled industrial growth and in turn industrial might and that other nations came to regard mineral self-sufficiency as one of the chief goalsof economic nationalism.

Jan 1, 1949

By A. L. Ph. B. Holley

(Read at the Philadelphia Meeting, February, 1878.) THIS paper is an abstract and a discussion of results obtained by the United States Test Board in experiments upon 14 brands of wrought iron, most of which are well known and of high repute.* The iron was all intended for chain-cables; it was tested in the form of bars, usually of nine sizes, from 1 inch to 2 inches round, and also in the forms of single links and short chains. Not less-than 2000 tensile tests were made, each showing elastic limit, elongation, and reduction of area. This work was done with conspicuous intelligence and fidelity, at the Washington Navy Yard, by Commander L. A. Beardslee. Some important practical results and principles which he has developed, and others which he has confirmed, will be referred to. The chemical part of this work consists of 42 complete analyses (including slag), by Mr. Blair, chemist to the Board. EFFECTS OF COMPOSITION ON STRENGTH. Variations in the physical qualities of iron may he due to different composition, or to different treatment in manufacture, or to both these complex causes. In order to determine the specific causes of variation, one class of altering conditions should be made to vary largely, while the other classes should be kept uniform. Then another class should be varied, and so on, until the value of each is ascertained. As all the irons under consideration were intended to have that purity and refinement which was deemed indispensable in chain-cables, their chemical analyses are perhaps more important in proving that physical variations result chiefly from treatment, than in pointing out the specific effects of certain ingredients. While the subject of treatment-especially the increase of strength by greater reduction in rolling-may be the more important one, it can be best appreciated after we have familiarized ourselves with the gen¬eral chemical and physical characters of the irons. The typical facts are given in the following tables. * As the present object of the Board is not to compare the products of different makers, but to discover the physical effects of various composition and treatment, the irons are designated by letters rather than by their trade names.

Jan 1, 1878

By R. E. Allen

THERE was once a time when a practical oil man would appraise or buy a producing property on the basis of from $200 to $500 per barrel of average daily settled production. Curtailment-has, for the present at least, caused a virtual abandonment of the "barrel -of settled production" as a yardstick of, oil property value and in its place has come the "barrel of allowable production," which, although an artificial thing, is nevertheless now the principal factor governing the rate of ?pay out? or investment return. The potential production of a well, settled or otherwise, is of less importance in determining the present worth of a well than is the rate at which it may be produced. Speaking only of true potential for the moment, it is obvious that of two similar wells having the same potential, the one having the highest rate of allowable production would be worth proportionately more than the one of lesser allowable. The discount factor for deferred return and risk can easily vary the present values of the two wells by as much as 20 per cent when allowable rates are not greatly different.

Jan 1, 1934

By J. E. Dreier

The Pachuca - Real del Monte district has produced about 46.6 kt (51,300 ton) Ag from subvolcanic vein deposits. Three types of wall rock alteration are spatially related to the veins: K-feldspar, propylitic, and phyllic. K-feldspar alteration occurs within veins; propylitic alteration occurs in fractured rocks between veins; and phyllic alteration occurs above veins. Concentrations of some trace elements in altered rocks relative to unaltered rocks are summarized below. [ ]

Jan 1, 1983

By R. P. Aikman, F. G. Miller, J. M. Podgursky

In response to the growing demand for low-sulfur coking coal for iron-making, the coal industry is continually striving to perfect methods for cleaning coal to acceptable ash and sulfur levels while maintaining maximum product yield. By present standards the industry has adequate processes for cleaning coarse coal, (i.e., +28 mesh) at almost any desired specific gravity. However, in the case of fine coal (i.e., -28 mesh) neither of the two existing processes-froth flotation and hydrocycloning-in its present state of development yields products that are comparable in ash and/or sulfur content to products normally obtained from coarse coal processes. The work outlined in this article is part of a larger study directed toward maximum exploitation of froth flotation for fine coal processing. The concepts and data presented are now serving as a basis for designing fine-coal circuits in which improved efficiency is obtained by optimum use of froth flotation with other fine-coal processing methods.

Jan 7, 1967

By H. Papazian, Robert A. Lad

SINCE it can be shown both theoretically'' : and experimentally that disordered Cu3Au has a greater internal energy than the ordered alloy, it might be expected that its chemical reactivity would be greater. Experiments were initiated' to test this hypothesis. This note will describe some recent results obtained in the study of the rates of corrosion of ordered and disordered polycrystalline Cu3Au by aqueous FeCl., The work of Robertson' has indicated that the attack by such solutions is intergran-ular and highly orientation dependent. It was of interest to see whether the order-disorder effect was great enough to overcome the variations from specimen to specimen which would arise from this type of attack. The polycrystalline alloy specimens (0.020 in. wire, 1¾ in. long) were preannealed in ½ atm H, at 700°C for 2 hr. The subsequent heat treatments to produce order and disorder were performed in M atm He. Disordered specimens were obtained by heating at 450°C for 2 hr and quenching in water. Ordered specimens were produced by heating for 2 hr at 450°, furnace cooling to 380°, and soaking at 380°C for 80 to 90 hr. Room temperature was reached by cooling to 150" at a rate never exceeding 7" per hr, and water quenching from 150°C. The specimens so produced exhibited electrical resistivities characteristic of the two states; of the order of 11.27x10 ohm-cm for the disordered, and 4.28x10 ohm-cm for the ordered specimens. The corrosion rates were studied at 30°C in ferric chloride solutions of several concentrations (?,¼, 1.5, and 1 molar). The specimens were attached to a stirrer during the tests. Tests were interrupted at intervals, and the specimen weight change was determined after washing and drying. Analysis of the solutions showed that the attack was limited to the copper. The higher corrosion rate for the disordered alloy, as illustrated in Fig. l, is typical of the results obtained. The effect of variation in ferric chloride concentrations is indicated in Table I for typical specimens. The variations in the ratio of reactivity for disordered and ordered specimens at the different concentrations are within experimental error, and the best value is estimated to be near 1.4. The experimental variation was due in part to the mode of attack, as mentioned, and in part to the fact that films were formed on the specimens under some conditions. Electron diffraction patterns of the films were very complex and indicated the presence of metallic iron, as did chemical analysis. In an attempt to eliminate the difficulties arising from the mechanism of attack, single crystal specimens were used. A greater reaction rate was again measured for the disordered specimens, but the reproduci-bility was no better than that for the polycrystalline metal. This would indicate that film formation was primarily responsible. It was concluded that the reaction with aqueous ferric chloride served to demonstrate that the reactivity of disordered Cu3Au is greater than that of the ordered alloy. However, the difficulties with film formation did not permit determinations of a precision great enough to warrant extension of the study to partially ordered alloy systems.

Jan 1, 1957

By H. F. Winham

The history, development, subsurface geology, production, economics and estimated reserves are discussed in this paper. The Magnolia structure is an anticline with a known maximum structural relief at 372 ft., and the areal extent of the producing acreage is 4494 acres. Production is obtained from the Smack-over oölitic lime and 116 successful wells have been drilled. The field, which was developed on 40-acre spacing, has been under strict control. It is believed to be producing with a strong water drive, To date it has produced more than eighteen million barrels and the estimate of ultimate recovery is 220 million barrels. Early History The Magnolia field is in colurnbia County, Arkansas, T. 17 s., R. 19 and 20 W. Various geologists had long been interested in this general area, and as early as 1921, John F. Magale was able to define a surface structure. The first wildcat, one of the first in Columbia County, was drilled in 1923 by Mid-States Oil Co., in sec. 10, T. 17 S., R. 20 W. This well was about 11/2 miles northwest of the Kerlyn oil Company's discovery well and was based on surface geological work done by Jewel and Dobie. Subsequently, several shallow wells that were not carried below the Upper Cretaceous beds were drilled in the immediate area of the discovery well, but none of them contained any commercial showings of oil Or gas. In the latter part of 1935, Elam and Magale (or Southwood) Garrett NO. I was located in sec. 13, T. 17 S., R. 20 W., 3/4 mile east of the discovery well. It was drilled to a total depth of 4018 ft. in the lowermost Glen Rose beds but failed to obtain any showings of oil or gas. Interest had been stimulated in this general area, however, by the discovery of several oil fields, mainly Glen Rose oil production in the Rodessa field in Louisiana in 1935, Smackover lime productioil in Snow Hill in May 1936, production from the Cotton Valley formation in Schuler in 1937, and Smackover lime production from the Buckner field in November 1937. With this background and subsequent seismic work, which was carried on partly because the old shallow wells drilled in the township had shown evidence of closure in the Upper Cretaceous beds, the discovery well, Kerlyn Oil Company's Barnett No. I, Sec. 14, T. 17 S., R. 20 W., was originally projected to a total depth of 6300 ft., to test the equivalents of the Morgan sands of the Cotton Valley series, then producing at Schuler. The well was carried to a depth of 6325 It. and tested the objective beds without finding commercial production. In the meantime, however, one well had found production in the Jones sand and another in the Smaclrover lime at Schuler. Kerlyn immediately made arrangements to deepen the Barnett well to the Smackover lime. The top of the Smackover lime was encountered at 7618 ft. and the well

Jan 1, 1943

By H. F. Winham

The history, development, subsurface geology, production, economics and estimated reserves are discussed in this paper. The Magnolia structure is an anticline with a known maximum structural relief at 372 ft., and the areal extent of the producing acreage is 4494 acres. Production is obtained from the Smack-over oölitic lime and 116 successful wells have been drilled. The field, which was developed on 40-acre spacing, has been under strict control. It is believed to be producing with a strong water drive, To date it has produced more than eighteen million barrels and the estimate of ultimate recovery is 220 million barrels. Early History The Magnolia field is in colurnbia County, Arkansas, T. 17 s., R. 19 and 20 W. Various geologists had long been interested in this general area, and as early as 1921, John F. Magale was able to define a surface structure. The first wildcat, one of the first in Columbia County, was drilled in 1923 by Mid-States Oil Co., in sec. 10, T. 17 S., R. 20 W. This well was about 11/2 miles northwest of the Kerlyn oil Company's discovery well and was based on surface geological work done by Jewel and Dobie. Subsequently, several shallow wells that were not carried below the Upper Cretaceous beds were drilled in the immediate area of the discovery well, but none of them contained any commercial showings of oil Or gas. In the latter part of 1935, Elam and Magale (or Southwood) Garrett NO. I was located in sec. 13, T. 17 S., R. 20 W., 3/4 mile east of the discovery well. It was drilled to a total depth of 4018 ft. in the lowermost Glen Rose beds but failed to obtain any showings of oil or gas. Interest had been stimulated in this general area, however, by the discovery of several oil fields, mainly Glen Rose oil production in the Rodessa field in Louisiana in 1935, Smackover lime productioil in Snow Hill in May 1936, production from the Cotton Valley formation in Schuler in 1937, and Smackover lime production from the Buckner field in November 1937. With this background and subsequent seismic work, which was carried on partly because the old shallow wells drilled in the township had shown evidence of closure in the Upper Cretaceous beds, the discovery well, Kerlyn Oil Company's Barnett No. I, Sec. 14, T. 17 S., R. 20 W., was originally projected to a total depth of 6300 ft., to test the equivalents of the Morgan sands of the Cotton Valley series, then producing at Schuler. The well was carried to a depth of 6325 It. and tested the objective beds without finding commercial production. In the meantime, however, one well had found production in the Jones sand and another in the Smaclrover lime at Schuler. Kerlyn immediately made arrangements to deepen the Barnett well to the Smackover lime. The top of the Smackover lime was encountered at 7618 ft. and the well

Jan 1, 1943

By Ronald W. Klusman, Erik B. Nelson

The Front Range portion of the Colorado Mineral Belt is an extensive area of mineralization with mining activity dating from 1859 with the discovery of large gold deposits. After an initial boom period and gradual diminishing production, present activity is restricted to molybdenum in Clear Creek County, uranium in Jefferson County, and several small operations extracting gold and silver in Clear Creek and Gilpin Counties. Gold and silver have dominated the production in the Front Range, though the complex mineralization created milling and smelting problems and it is postulated that considerable amounts of precious metals remain in the mine dumps. This area is plagued by a severe mine drainage problem, with Clear Creek most impacted by many draining mines and tailings in the basin. Boyles et al. Moran and Wentz, Wentz, Wildeman et al., have examined various aspects of the impact of mine drain¬age in the Clear Creek basin. The primary objective of this study was to collect data on the tailings, drainages, and leaching experiments in order to make preliminary suggestions for reducing the impact while recovering metal values to offset treatment costs. A variety of leaching experiments were performed on tailings from the Nevada Gulch area in the Central City mining district. Leachings were performed in vertical tubes indoors and wooden boxes exposed to the outside environment. In the leaching experiments, the leaching solution, grain size, and residence times were varied, while forced aeration was used in some experiments. Bacterial nutrient 9K° and mine drainage were used in some of the experiments. A total of 14 additional tailings samples were analyzed for base and precious metals. The composition of the mine drainage and tailings used in the leaching experiments, as well as data on the additional samples are shown in [Table 1]. Leachate samples were taken periodically for analysis until compositions leveled off. Results and Discussion Leaching with distilled water was used as a control and best illustrates the basic behavior of the leaching process for zinc in a vertical tube [(Fig. 1)]. More acidic leachings increased concentrations of metals as did smaller grain sizes, though the time required increased significantly. Mine drainage with its high concentration of dissolved iron sometimes decreased the heavy-metal concentration in the leachate due to oxidation of Fe 2 and precipitation of Fe(OH)9 which absorbs some of the dissolved heavy metals. In the larger scale experiment carried out in the simulated leaching pad, substantial concentrations of metals were attained in the final leachate after one month. In this experiment the leachate was not recycled, but allowed to saturate the tailings continually with evaporation loss made up by additions of Quartz Hill drainage and nutrient 9K. The concentration of the metals in the leachate and the increase over the input solution are given in [Table 2]. Heap leaching of low-grade copper and uranium ores is successfully carried out in many districts, enhanced by the metabolism of autotrophic bacteria of the Thiobacillus-Ferrobacillus group. These ubiquitous organisms enhance metal leaching, and general aspects of heap leaching are discussed by Malouf, Trudinger, Pings, and Duncan et al. Conclusions and Recommendations Returning to the primary objective, how to reduce the mine drainage impact and recover metal values, we need to consider how the data may suggest avenues toward this objective. Boyles, et al., considered various

Jan 1, 1977