Search Documents

By Thomas Leonard Watson

Jan 1, 1906

By J. E. House, J. L. Drobnick, R. R. Swanson, D. W. Agers

The paper describes an improved process for the recovery, purification, and concentration of copper values from acidic dump leach liquors. The process employs a new liquid ion exchange material (LIX® 64 reagent) capable of separating copper values from iron and other impurities common to dump leach liquors in the typical pH range of 1.4-3.0. Properties and performance of the reagent are discussed. Design scale-up information for both pilot plants and commercial installations, including preliminary economics, are presented. Economic considerations include the production of electrolytic copper from the purified copper aqueous concentrate. INTRODUCTION Since the commercial acceptance of the liquid ion exchange process in the mineral processing industry, it has been predicted that a wide selection of chemical reagents to efficiently and economically separate many metals in solution under a wide range of conditions would be commercially available. Several years ago, General Mills began a basic research and development program to determine if it were possible to develop a reagent to extract economically metallic ion from existing process streams. Progress toward reaching this objective was reported in late 1963, when development of quantities of LIX -63 reagent, a highly selective reagent for the extraction of copper, was introduced. The properties of this reagent are described in a previous paper.' The development work with this reagent indicated that perhaps the largest potential application for a copper extractant, the treatment of acidic dump leach liquors, would not be economically possible with LIX-63 because of limitations of the reagent to extract copper below a pH of 3.0. The relatively small pH adjustment required with LIX-63 would result in a significant processing cost and the undesirable precipitation of ferric hydroxide from the liquor. This pointed to the need for another copper extractant which would extract copper from dump leach liquors without pH adjustment. General Mills was successful in synthesizing a molecule which does not have the pH limitation of the LIX-63, yet possesses the selectivity-solubility properties required of a metallic extractant. The resulting LIX-64 reagent broadens the pH range from which copper can be effectively extracted and separated from other metallic impurities. Of special significance is the fact that the reagent, LIX-64 was developed by combining the technical requirements of a specific problem in hydro-metallurgy with theoretical organic and physical chemical principles.

Jan 1, 1967

The income of the Institute is derived mainly from dues, advertising in MINING AND METALLURGY and sale of publications. These sources are fortunately supplemented by the interest from invested funds now amounting to over $500,000, a considerable portion constituting endowments for especial purposes. Aside from the medal funds the principal endowments are the James Douglas Fund for support of the Library, the Rocky Mountain Fund and the Seeley W. Mudd Memorial Fund. The income from the two last named is available for the support of research and a variety of other purposes. It is allocated by the Board of Directors upon recommendation of standing committees in each case. An active effort is being made to increase the endowments of the Institute, it being felt that unusual opportunities exist for research and public and professional service through the organization.

Jan 1, 1939

By F. H. McDowell

DURING the last eighteen months the Tilly Foster Iron Mine Company, the President of' which is Mr. E. I?. Hatfield and the Managing Director Mr. B. G. Clarke, has been carrying out a plan

Jan 1, 1889

By D. W. Fuerstenau

In 1940 Schuhmann1 showed that the size distribution of a comminuted material can be expressed by the following empirical relationship: y = 100 (|f [i] where y is the cumulative percentage of material finer than size x, k is a size modulus, and a is a distribution modulus which is constant for a given material and machine. During the past few years, considerable emphasis has been given to the investigation of the extent of size reduction resulting from the expenditure of mechanical energy in crushing and grinding. Recently Schuhmann' presented a derivation of the energy-size reduction relationship by postulating that comminution in a device such as a ball mill can be considered to be the summation of many single comminution events, each of which yields a size distribution of particles following the Schuhmann size distribution equation. By grinding

Jan 1, 1961

By R. O. Williams

A recent article by Chernock, Singer, Mueller, and Beck 1 which supports the use of the integral of I sin $ d$ for comparing fiber texture data does not settle what happens to I sin ø as ø approaches zero, where I is the diffraction intensity for poles oriented 0 deg from the fiber axis. They indicate that they believe that it should approach some constant value (that is, I increases without bound) and the fact that in reality it does not was a result of the diffraction

Jan 1, 1960

By Sir Robert Hadfield

SINCE the writer has been intimately connected with the development of manganese steel for many years, some remarks upon the early work with regard to the rolling and forging of this material might he of interest, and particularly as to the question of rails of special quality and of superior wearing qualities. In a paper on Iron Alloys, with Special Deference to Manganese Steel, read before this Institute at the International Engineering Congress in Chicago in 1893,1 the writer mentioned that, about 20 years ago, his firm in Sheffield produced railroad material, such as tires and axles, of forged and rolled manganese steel, thus showing that this product could be manipulated and worked up into the various required forms. The tires illustrated in the paper referred to above formed a particularly difficult class of work to produce in a special steel, but no special obstacles were met with Although there was no difficulty at that time in making and producing manganese steel in various forms, forged, rolled or pressed; nevertheless, on account of its higher expense, sufficient encouragement

Jan 2, 1914

[ ]

Jan 1, 1938

By I. L. Greninger

THE property of the Andes Copper Mining Co. is in the central part of the Republic of Chile, Province of Atacama, 147 km. (91.5 miles) eastward by rail from the port of Chanaral. At this point the Andean system is made up of two principal ranges. The mine is on the westerly slope of the outer, or western, range, at a mean elevation of 3250 m. (10,500 ft.). A meter-gage railroad extends from the company's port at Barquito, near Chañaral, to the reduction plant at Potrerillos. This road has a total length of 151 km. (94.0 miles), of which 93 km. (57.79 miles) are owned by the Andes Copper Mining Co. The remainder of the road is owned by the state. The company operates its trains over the portion of the road owned by the state, under an agreement with the Chilean Government. The mine is connected with the reduction plant by a meter-gage railroad, 10 km. (6.214 miles) long, which extends from the coarse-ore bins at the metallurgical plant to the underground storage bins at the mine. Tunnels make up 60 per cent. of the total length of this railroad. As is characteristic of the Andean region in Chile, the topography of the locality is extremely rough, and a number of points near the mine have elevations of from 15,000 to 16,000 feet. History of Potrerillos Mine The ore occurrence has been known for many years, and many of the claims under individual ownership were worked in a small way before the property was acquired by the present owner—the Andes Copper Mining Company. The highest grade oxide ores near the surface were mined by primitive methods and, after sorting, the product, assaying around 15 per cent, copper, was hauled by mule carts a distance of about 80 km. (49.71 miles)

Jan 1, 1929

By J. B. Fletcher

The Miami mine first started operations in 1910. For convenience, the history of the orebody can be divided into the following categories (Fig. 1): 1) 1910 to 1925: 24.4 million tons of high grade ore, mined by top slicing, sublevel caving, etc. 2) 1926 to 1954: 102 million tons of low grade ore, mined by block caving.

Jan 1, 1961

By Robert Bakish, William D. Robertson

AFTER more than fifty years of investigation and continuing failure in service, a satisfactory mechanism to explain stress corrosion cracking in homogeneous alloys is still lacking. The relative chemical activity of grain boundaries and adjacent grains, inferred from the boundary structure, has been used to explain intergranular cracking in a brass.' This concept is probably correct as a general hypothesis, but it requires much more extensive development in order to explain satisfactorily the observed phenomena. For example, the specific function of the solute in an alloy must be considered, because intergranular failure does not occur in pure metals,' which are structurally similar to homogeneous alloys. Also, in this connection, an inter crystalline fracture path in binary copper alloys can be changed to a transcrystalline path by relatively small ternary additions.' The fracture path in ß brass is predominantly transcrystalline,' in contrast with an inter crystalline path in a brass. Whether the two different fracture paths are the result of a difference in composition, crystal structure, or the state of long range order is unknown and cannot be determined with ß brass, because only the ordered state can be obtained at room temperature. The study of chemical activity at structural sites in the Cu-Zn system is restricted by the formation of opaque films in an ammonia environment in which stress corrosion cracking is generally observed. Furthermore, both components of the alloy are chemically active and the interpretation of observations is therefore relatively complicated. The Cu-Au system is a better choice for the purpose of studying structural factors. In particular, CuAu is very susceptible to cracking in ferric chloride and opaque films are not formed in this solution; it may be obtained in different states of long and short range order; and, finally, only copper is oxidized in dilute ferric chloride, which considerably simplifies the chemical problem. To provide information necessary for a more general explanation of stress corrosion cracking in homogeneous solid solutions, the following structural factors have been investigated in a Cu-Au alloy having a composition corresponding to Cu,Au: 1) the effect of long and short range order; 2) the structural sites from which copper is removed from the annealed and cold worked polycrystalline alloy; and 3) the effect of annealing time and temperature on structural reactions in the cold worked alloy. Experimental Procedure A Cu-Au alloy of nominal Cu3Au composition was cast from cathode copper and high purity gold and fabricated into sheet and wire. Chemical analysis for copper and gold indicated 48.92 wt pct Cu and 51.01 pct Au. Quantitative spectrographic analysis indicated 0.01 pct Ag, 0.002 pct Pd, 0.001 pct Pb, and 0.002 pct Fe, with traces of magnesium, silicon, and zinc. Presumably most of the remaining 0.055 pct corresponds to the limits of analytical precision. Heat treatments of wire and sheet were conducted in argon or vacuum. Wire specimens, 0.064 in. diam, were heated for 1 hr at 850 °C to establish a definite

Jan 1, 1957

By . M. Muskat

A THEORETICAL consideration of the mechanics of various water-flooding systems with the viewpoint of comparing their relative merits involves the study of two fundamental properties of such systems. On the one hand, it is important to determine the efficiency of the flood as measured by the percentage of the total area that is swept out by the encroaching water before water actually reaches the output wells. This is really a measure of the regional tendency of the water to "bypass" the oil. On the other hand, the various systems must be compared from the viewpoint of their resistances which determine the rate of fluid production obtainable for given pressures maintained at the water input wells. The first of these questions has been studied and very definite answers have been obtained by means of simple electrolytic models.1 These models showed that, in an ideal system, the percentages of the areas flooded out before water reaches the output wells are about 57 per cent for the direct line-drive flood (the input and output wells being equally spaced and placed in alternate parallel lines), 74 per cent for the regular five-spot network, and 79 per cent for the seven-spot network. With respect to the efficiency of the usual flooding arrangements, they are, therefore, given quite accurately by the above numbers. With regard to the resistances of the flooding networks, electrical conduction models have also been used successfully2 and are well adapted to the problem of determining experimentally the pressure distribution and streamlines, or over-all resistances of specific flooding networks. However, such models do not permit readily a study of the effect of changing dimensions or configuration within a network, since a new model must be made up for each set of dimensions considered.

Jan 1, 1933

By W. L. Saunders

WHEN work was begun in September, 1910, on the rock excavation for the foundation of the gigantic dam at Valhalla, N. Y., which is to convert Kensico lake into an important storage reservoir of the Catskill Aqueduct system, one of the first steps taken by the contractor, H. S. Kerbaugh, Inc., was the development of a quarry to supply the stone needed in the construction work.The importance of a bountiful supply of suitable rock in an accessible location is apparent when it is considered that nearly a million cubic yards of cyclopean masonry will be contained in the completed structure, not to mention dimension and facing stones, concrete blocks, and mass concrete. The dam structure will be over 1800 ft. long and about 170 ft. above the present river bed. However, for a distance of some 800 ft., it will be carried down to solid ledge rock, which will make the finished structure about 300 ft. in maximum height. It will be about 200 ft. thick at the base and directly beneath the coping it will be 28 ft. thick. This dam will raise the reservoir surface 110 ft. above old Kensico lake. The reservoir capacity will be 29,000,000,000 gal.-equal to New York's total needs for over two months. The contract price for this work is nearly $8,000,000 and is second only in amount to the cost, over $12,600,000, of the Ashokan Reservoir work. Fig. 1 is a view of the dam site.

Jan 2, 1914

By Alicia O&apos, Overbeck, Reardon

DIFFIDENTLY, because don'ts are rarely greeted with cheers; humbly, because I, myself, have never lined up with the irreproachables, I venture on the subject of manners for the mining camp matron. Mining camps can be divided roughly into two types-the large, opulent settlement that blooms like the rose about a strong mine in full operation; and the puny group of adobe huts, or calamina shacks, or even canvas tents flung down in the wilderness to shelter the gay pioneers of a shining prospect or the shattered survivors of a lost hope. Of the first, I know nothing; but in the second, I have spent some of my best years, and from its curious code of morals and manners, its comic hates and its unreasoning loves, its high impatience and its engulfing kindness, I have charted the narrow .and pitted path which must be trod by the woman who would success¬fully live therein.

Jan 1, 1936

By Alicia O'Reardon

DIFFIDENTLY, because don'ts are rarely greeted with cheers; humbly, because I, myself, have never lined up with the irreproachables, I venture on the subject of manners for the mining camp matron. Mining camps can be divided roughly into two types-the large, opulent settlement that blooms like the rose about a strong mine in full operation; and the puny group of adobe huts, or calamina shacks, or even canvas tents flung down in the wilderness to shelter the gay pioneers of a shining prospect or the shattered survivors of a lost hope. Of the first, I know nothing; but in the second, I have spent some of my best years, and from its curious code of morals and manners, its comic hates and its unreasoning loves, its high impatience and its engulfing kindness, I have charted the narrow .and pitted path which must be trod by the woman who would success¬fully live therein.

Jan 1, 1936

By E. C. Pechin

THE Lucy furnace, owned by Messrs. Carnegie, Kloman & Co., and located on the Alleghany River, on the outskirts of Pittsburgh, is a splendid modern furnace, 75 feet high, and 20 feet bosh. She had been working well on low grade ores of about 50 per cent., producing daily 68 to 75 tons. There was on stock 500 tons of Republic ore, one of the purest and best of the Lake Superior ores, averaging over 68 per cent. of iron, which had been procured for the purpose of making a trial for Bessemer iron. This was charged by itself, and Mr. Skelding, the founder, reports that he did not succeed in getting a single cast when it came down, before the furnace chilled from the hearth to the top of the boshes, some 25 feet. Every effort was made to save her, without avail, and the disagree-

Jan 1, 1874

Members of the American Institute of Mining and Metallurgica Engineers can now secure copies of the Journal of the Institute of Metals of Great Britain at a special price of $5 for the two volumes issued during the year, postage extra amounting to approximately 25 cents. This Journal is one of the best books dealing with the subject of non-ferrous metals and alloys and this arrangement with the Institute of Metals permits our members to take advantage of this specially low price. Back numbers of the Journal can be purchased on the same basis. The Journal can be ordered directly through the office of the Institute of Metals, Great Britain 36 Victoria St., Westminster, S. W. I., London, England. The letter should be accompanied by an international money order and a copy sent to Secretary of the A. I. M. E. in order that the membership record may be checked.

Jan 9, 1919

By Edmund C. Pechin

The Lucy furnace, owned by Messrs. Carnegie, Kloman & Co., and located on the Alleghany River, on the outskirts of Pittsburgh, is a splendid modern furnace, 75 feet high, and 20 feet bosh. She had been working well on low grade ores of about 50 per cent., producing daily 68 to 75 tons. There was on stock 500 tons of Republic ore, one of the purest and best of the Lake Superior ores, averaging over 68 per cent. of iron, which had been procured for the purpose of making a trial for Bessemer iron. This was charged by itself, and Mr. Skelding, the founder, reports that he did not succeed in getting a single cast when it came down, before the furnace chilled from the hearth to the top of the boshes, some 25 feet. Every effort was made to save her, without avail, and the disagree-

PICK AND SHOVEL CLUB, CASE SCHOOL OF APPLIED SCIENCE The last meeting of the year of the Pick and Shovel Club of Case School of Applied Science was held on May 20, 1919. The speaker, Dr. Zay Jeffries, gave a very instructive and interesting talk on the Metallography of Non-ferrous Metals. The club has had a very successful year in spite of the loss of a few months time through the S. A. T. C. Among the speakers for the year were Dr. F. R. Van Horn, Dr. C. H. Fulton, and Dr. W. R. Veazey of our school; Dr. E. S. Moore of Penn. State College; Dr. Ansel St. John, of the National Carbon Co.; and Mr. V. S. Bidle, of the W. S. Bidle Co. The graduating members wish the club the best of success for the coming year. BERTRAND R. WARMELING, Secretary.

Jan 7, 1919

By H. J. Gerritsen

From presently available components a portable, rugged, reliable apparatus can be built which will be able to detect methane concentrations of 0.1% and lower in air. Sensitivity and design considerations of the apparatus are given. Ways to build even simpler and cheaper apparatus in the future are indicated. Traditionally the problem of detecting and monitoring the presence of dangerous gases present in small concentrations in air has been a difficult one. Whether canaries,' or sophisticated chemical or thermal conductivity methods are used, they seem to be either slow, cumbersome, or otherwise not completely satis factory. A seemingly natural way of gas detection is to measure the strength of absorption undergone by light of a wavelength that the gas to be detected absorbs. This method has been difficult to apply in view of the low power output over a narrow wavelength range in the infrared from traditional glow bar light sources. Besides, the apparatus to select such a narrow band of wavelengths is quite costly and complex. The use of a laser solves these problems simultaneously. Although a variety of lasers are available to detect a variety of gases (such as carbon monoxide or methane) whose early detection would be desirable, this paper deals exclusively with the use of lasers for methane detection. ABSORPTION SPECTRUM OF METHANE IN AIR The absorption spectrum of pure methane is very well known.2-4 There are four fundamental vibrations, all occurring in the infrared of which only two absorb strongly. They occur at 3.3 µ and 7.7 µ. The absorption spectrum is quite complicated due to the fact that the methane molecule can rotate in a variety of rotational quantum states. These rotational states are furthermore split by anharmonic forces such as the Coriolis force.4 When methane is present in air at atmospheric pressure, much of the very fine structure due to the anharmonic force is washed out since the pressure broadening is of the same magnitude as the splitting due to anharmonicity. For most of the spectrum at 3.3 µ, the rotational lines are typically separated by 0.01µ while the individual linewidth is 0.0001 µ. It is thus very important that the laser emit at a wavelength that coincides with one of these rotational lines. Before elaborating on the point that such a laser exists and how it performs, it is necessary for later discussion to point out that in the

Jan 1, 1967