Search Documents

By A. M. Gaudin, D. W. Fuerstenau

By streaming potential techniques, the zeta potential of quartz has been measured as a function of the concentration of dodecylammonium salts at different pH values. These experiments indicate that adsorption of dodecylammonium ions takes place as individual aminium ions until a certain critical concentration is reached in the double layer, at which point the adsorbed collector ions begin to associate into patches of ions, called hemi-micelles. Because of its effect on the surface potential of quartz, pH controls the adsorption of dodecylammonium ions. The value of cooperating agents and nonionized constituents of flotation systems is discussed. A PREVIOUS investigation' of the role of pH in the flotation of quartz with anionic collectors is here extended to an inquiry of how the cationic collector, dodecylammonium acetate, is adsorbed at the quartz-solution interface. The equilibrium amount of this collector adsorbed by quartz has already been measured as a function of concentration and pH.2,3 The weight of prior evidence has suggested that two mechanisms are involved in the adsorption of this collector by quartz, but with existing adsorption measurements alone it is not possible to determine what the mechanisms are. Gaudin and Bloecher2 postulated that a polymolec-ular adsorption coating begins to form before the first monolayer has been completed. Gaudin and Morrow4 indicated that a similar situation might exist in the film of dodecylammonium ions on hematite. A study of electrokinetic potentials at the quartz-solution interface provides some detail toward a fuller understanding of the adsorption mechanism. Experimental Results The zeta potential at the quartz-solution interface was calculated from streaming potential data measured with the apparatus described in detail in a thesis by Fuerstenau5 and briefly in a paper by Gaudin and Fuerstenau.1 The quartz used in these experiments was a 48/65-mesh fraction prepared in the manner described previously.' Zeta potential of quartz was obtained for various amounts of the amine salt at pH 4, 7, 10, 11. In

Jan 1, 1956

By Blake M. Loring, Robert A. Colton

MELTING procedures for most metals and alloys usually include some provision for the control of oxygen, since this element frequently has some undesirable effect on the properties of the metal or alloy concerned. In the melting of the various bronzes, this is especially true, since oxygen can be introduced into the melt in a number of ways, most of which are difficult to control. In making bronzes from virgin materials, oxygen is usually present in the commercial grades of copper used; electrolytic he refined copper ingots usually contain from 0.02 to 0.05 per cent oxygen. When ingot metal or scrap bronze is used in the charge, oxides are almost always present to some degree. Under certain melting conditions and in certain types of melting equipment the atmosphere over the metal may be highly oxidizing. This, of course, may be desirable in the melting practice used, but is certain to introduce appreciable amounts of oxygen into the melt, and that may not be entirely desirable. From the foundry viewpoint oxygen may have several harmful effects on bronzes. The formation of excessive amounts of oxides may produce drossy metal, which, in turn, means dirty castings and a potentially high rejection rate. It is claimed, too, that oxides in the metal may combine with hydrogen to form steam and thereby produce porosity in certain of the bronzes. The presence of certain refractory oxides, such as SnO2, may be undesirable from the viewpoint of making machining difficult, or as possible stress-raisers in the metal matrix. It is often said that excessive oxide present in the liquid metal makes the metal run sluggishly. Since it appears impractical to try to control the amount of oxygen introduced into the metal beyond taking the economical limit of precaution about charging dirty scrap, it would seem that control of the oxygen content of the liquid metal offers the most promising approach to this problem. This might be done by using slags, or covers, or by the use of some element or compound added to the melt to remove oxygen preferentially. Most aspects of this problem have been considered and considerable work has been done along these lines. A reconsideration of the problem is indicated, however, by the controversial nature of the evidence at hand, especially on the possibility of using a chemical deoxidizer to control the oxygen content of bronzes. CHOICE OF DEOXIDIZER The choice of the chemical agent selected as a deoxidizer would naturally depend first on the alloy in which it is to be used; in this particular case the alloy is Navy gun metal. In Table I are listed a group of elements that might be considered as

Jan 1, 1946

By J. Landau, A. Dim, R. Houlihan

Recent developments in the application of solvent extraction in hydrometallurgical processing make it desirable to reassess the present state of availability of suitable equipment for these applications. The range of solvent extraction applications now includes very large scale applications with a modest demand on separation performance (the treatment of some base metals) and applications in which the decisive factor is a very high requirement on separation performance. The extraction column to be described in the present paper is of the type in which mechanical energy is provided for the two- liquid system inside the column. The active elements for this are reciprocating sieve plates designed and mounted so as to uniformly load the driving mechanism, to eliminate vibration of the plant, to have sufficient control over the degree of dispersion of the dispersed phase, and to reduce axial mixing effects, which are highly detrimental to the separation performance of production-scale plant. The operating features of the reciprocating-plate column will be illustrated mainly by experimental results obtained on a 4" diameter column in the extraction of uranyl nitrate with TBP. Some mechanical features of the operation of reciprocating-plate columns will also be discussed.

Jan 1, 1973

(SECRETARY'S NOTE.) The following discussion of the papers of Van Hise, Emmons, Lindgren and Weed, read at the Washington meeting, February, 1900, and printed on pp. 282 to 498 of this volume, comprises communications to the Secretary, received at various times before the Richmond meeting, February, 1901, and, for the most part, presented at that meeting. These communications are introduced at this point in the present volume, in order that they may precede the papers of Vogt, hemp, Lindgren, Rickard, etc., presented at Richmond, and therefore not forming part of the material considered in them. Since many of the contributors have mentioned in one communication several of the papers referred to, no attempt is here made to divide their remarks and distribute the fragments under separate headings. In each contribution, however, the several topics are indicated by subtitles. R. BECK,* Freiberg, Saxony : Prof. Veal Hise's Paper.-The paper of Prof. Van use (p. 282) represents a great step of scientific progress, in that the circulation of underground waters has never before been presented with such clearness, ill the light of modern chemical and physical knowledge. The theories of the formation of ore-deposits which follow the author's general survey of the currents and solvent power of atmospheric waters in the earth's crust do not, indeed, seem to be novel, being essentially an amplification of Le Conte's views; but the proofs adduced in their support are in many particulars so original that no one can read without profit this portion of the paper. Entirely new (though largely in agreement with the papers of Emmons and Weed, presented at the same meeting of the Institute) are the sections dealing with the formation of the rich sulphides of the precious metals, and especially the regeneration of normal sulphides, such as galena, etc., in vein-zones immediately beneath the ground-water level. Nevertheless, it appears to me that Prof. Van Hise, in the course of his most instructive exposition of unquestionable, yet still locally limited, phenomena, has been too much biased in favor of the " descensionists." This is indicated by the small importance which he attaches to the intimate genetic relation between epigenetic deposits and the plutonic hearths of the earth's interior.

Jan 1, 1902

By Harlan W. Nelson, James B. Purdy

The great majority of stokers used in residential heating installations are of the clinkering type. Because of inherent characteristics of the underfeed combustion process as it occurs in these small stokers, and because of the wide range of operating conditions encountered in residential heating schedules, not all bituminous coals can be used successfully in residential underfeed units. The problem of providing consumer satisfaction has been attacked by the joint efforts of the stoker manufacturers and the coal industry; the stoker manufacturers have been concerned with improving their product to permit the use of a wider range of coals, and coal operators have made every effort to market selected and better prepared coals. In view of the wide range of physical characteristics and chemical properties of bituminous coals, the problems are real and are receiving increased attention. Some twelve years ago a laboratory method was developed at Battelle Memorial Institute for the relative evaluation of coals for use in residential underfeed stokers. The method was developed in conjunction with work being done at that time for Bituminous Coal Research, Inc., and for individual coal producers, to obtain information on the characteristics of coal that determined the successful performance of the small stoker. Details of the equipment and test procedure were given by R. A. Sherman1 in a paper presented at the University of Illinois Fifth Short Course in Coal Utilization. During the past several years, the evaluation of over forty different coals has been determined by investigations sponsored at Battelle by coal operators in the eastern producing districts. The purpose of this paper is to compare the results and conclusions derived from the various tests with marketing experiences of the operators, and to discuss briefly the relationship of test results to standard laboratory determinations. Equipment Used in Tests Fig 1 shows schematically the equipment used in the evaluation tests. The stoker is a commercial model of conventional design, having a nominal feed rate of 30 Ib per hr. A special laboratory furnace is used, which is tightly sealed to prevent the entrance of secondary air. The complete stoker-furnace assembly is mounted on platform scales which permits the measurement of combustible weight losses occurring during the test. The furnace stack, in which are a thermocouple, flue-gas sampling tube, and smoke meter, is connected to the laboratory exhaust breeching through a friction-less connection. Through use of an auxiliary blower system, provision is made for the measurement of the air delivered by the stoker fan to the windbox. A water seal in the duct work eliminates inter-

Jan 1, 1950

By J. C. Febles

The use of iron for the precipitation of copper was known at least as early as the fifteenth century. Both Paracelsus and Basil Valentine refer to it in their writings, as early as 1500 A. D. It was used in Peru for this purpose prior to 1637, and at Rio Tinto, Spain, as early as the sixteenth century. The statement has been made repeatedly that in the early history of the mining industry at Butte, the practicability of this method of recovering copper from solution was overlooked, and that enormous quantities of copper-bearing water were allowed to go to waste, the copper in which might easily have been recovered at small cost; and that this oversight on the part of the mine operators was due to ignorance of this method of recovering copper. As a matter of fact, very little copper-bearing mineral was encountered in the mines of Butte until a depth of 400 or 500 ft. had been reached, and in many cases much greater depths were necessary to reach the copper-bearing zone. The water encountered in the upper levels (although in most cases quite highly mineralized) contained little or no copper, and it was only after considerable areas of copper-bearing ore had been uncovered and developed that copper sulphate began to appear in the mine water in any considerable quantity. In fact, the first water that was observed to contain copper carried it in such small amounts as to be of little or no importance. It was only after years of underground work had opened extensive areas of stopes, drifts, and other underground workings, these being subsequently filled with waste, nearly all of which contained small copper values, which became oxidized by exposure to the air and were acted upon by the slowly percolating mineral water, that the recovery of copper from mine water became commercially important.

Jan 1, 1914

By Albert Sauveur

AT the New York meeting of the Institute, February, 1914, Professor Hopkinson and Sir Robert Hadfield presented an important paper entitled Research with Regard to the Non-Magnetic and Magnetic Conditions of Manganese Steel.1 Any contribution on manganese steel by its discoverer necessarily carries with it much weight and is entitled to serious and close consideration. The momentous discovery of that alloy by Sir Robert Hadfield some 30 years ago was the signal for great activity in the field of alloy steels; and the remarkable results obtained in the last two decades probably constitute the most important modern advance in the metallurgy of steel. The authors of the paper referred to above are unable to reconcile with the allotropic theory the interesting results obtained by them in heat treating manganese steel. When they speak of the allotropic theory, however, I understand that they have more especially in mind the existence of beta iron. It is not my understanding that they question the occurrence of iron in the two allotropic varieties known as gamma and alpha. If I am wrong, I trust they will correct me. A careful consideration of the experimental results reported and discussed by the authors leads me to believe that on the contrary they can be very satisfactorily explained in terms of allotropy and that, in the light of our present knowledge, they cannot be accounted for in any other way. The physical properties of non-magnetic manganese steel described by the authors are those pertaining to iron-carbon alloys in which iron is present in the gamma condition, or, in other words, to austenite. The metal is then characterized by great tenacity and ductility and low elastic limit, while its hardness, mineralogically speaking, is not excessive, but of a special kind termed "tough hardness" by the authors. Even when subjected to the restraining influence of a large amount of manganese and of considerable carbon, however, relatively rapid cooling

Jan 9, 1914

By Tell Ertl, Ernest E. Burgh

The Bureau of Mines is operating an oil-shale mine 10 miles west of Rifle, Colo., as part of its Synthetic Liquid Fuels program. The purpose of operating this mine is twofold: First, to supply oil shale to an experimental Processing plant; and second, to develop practices and select methods for mining oil shale on a commercial scale at the lowest practicable cost. The second purpose—that of finding out how to mine oil shale most cheaply—entails considerable mining research. Since the drilling of oil shale probably will be one of the major items of the mining cost, fattors that influence drilling speeds were investigated. One phase of the drilling program was the development of a successful hard-surfaced rock-drill bit1 that can be used for drilling long holes in oil shale without changing bits. During that phase, drilling speeds were measured and drill cuttings were collected for assay and for screen sizing, when the cuttings from the individual tests were compared, a definite relationship was shown to exist between the drilling speed and the coarseness of the drill cuttings. Procedure Measurement of Drilling Speeds All drilling in the tests was done with a Model UMB-D-99W Gardner-Denver wagon drill. Round-lugged drill steel, 141 in. in diameter was used in 6, 12, and 18 ft lengths with 1/8-in. Timken H-type bits hard-faced with acetylene tube borium. The tests were made in the lower adit of the Bureau of Mines oil-shale mine; the grade of the oil shale drilled ranged from 18.6 to 42.7 gal per ton, During the experiments air pressure varied between 75 and go psi while water pressure remained fairly constant at 75 psi. All holes were drilled almost horizontally. Each drill hole was thoroughly cleaned of cuttings after being collared. The advance of the drill along the carriage was measured and recorded as the drilling speed in inches per minute. Method of Collecting Cuttings TO facilitate the collection of cuttings, each drill hole was collared in a smooth, vertical portion of the oil-shale breast (Fig 1). A galvanized-stee1 sheet was fastened to the breast below the area in which the hole was to be drilled. The cuttings washed out of the drill hole by the drilling water were guided by the steel sheet into a wooden box. The cuttings that remained in the drill hole after the drill was withdrawn were scraped out and placed in the same box as the cuttings washed out of the hole. After the cuttings from a I-min. drilling interval were collected, they were placed in flat metal pans. The fines were allowed to settle and the clear water was decanted. The cuttings then were dried in the sun.

Jan 1, 1949

By R. J. Jackson, D. E. Williams, W. L. Larsen

The phase diagram of the Ta-Zr system is presented with a discussion of the methods used in its determination. The solidus contains a minimum at 1820°C near 25 wt pet Ta. A complete solid solution exists at elevated temperatures between tantalum and ß zirconium. This solid solution decomposes monotectoidally at 800°C and 12 wt pet Ta. The maximum solubility of tantalum in a zirconium is slightly less than 2 wt pet, and decreases with decreasing temperature. The solubility of zirconium in tantalum is 5 wt pet at the monotectoid temperature and about 2 wt pet at room temperature. THIS investigation was part of a program of research on refractory metal alloy systems having potential application in nuclear reactor technology. Preliminary prop-ess has been reported in the Ames Laboratory annual research reports.l Most of the previously reported work on the Ta-Zr alloy system consisted of partial phase diagram investigations and the determination of the mechanical properties of the zirconium-rich alloys. Anderson eta1.2 studied alloys containing up to 30 wt pet Ta as part of an investigation of several zirconium alloy systems. These investigators also determined some of the mechanical properties of the alloys at room temperature and 650°C. In a discussion of Anderson's work, Pfei13 suggested that the bright phase in the microstructures of the intermediate alloys is a tantalum-rich solid solution or an intermediate phase in a matrix of ß zirconium solid solution. Litton,4 Keeler,5 and Chubb6 determined the mechanical properties of zirconium-rich alloys at ambient and elevated temperatures. Van Thyne and McPherson7 reported the tensile properties

Jan 1, 1962

By W. B. Gogarty

With the use of polymer solutions in secondary recovery operations, the need has developed to understand the mobility control mechanism. This study investigated mobility control by considering both permeability and rheological effects. Experiments used a high molecular weight, partially hydrolyzed polyacrylamide polymer. Flow studies took place in reservoir and Berea cores having zero oil saturation. Effective size of the polymer flow unit was inferred from Nuclepore filter tests. Clay studies indicated the particle size capable of decreasing the core permeability. Flushed permeabilities measured the approximate core permeabilities with flowing polymer solutions. These permeabilities were considerably lower than original values. With mobility data and the flushed permeability, maximum effective viscosities were determined for polymer solution flow in a core. Effective viscosities showed that rheological properties play an important part in mobility control with polymer solutions. The study showed that permeabilities decrease and stabilize with polymer flow. At the lower permeabilities, high shear rates exist in the cores. Because of the pseudoplastic character of the polymer solution, the high shear rates caused low effective viscosities. This condition pointed to the inefficient use of the potentially high viscosity of the polymer solution at low shear rates. INTRODUCTION In the oil industry, a great deal of interest is being shown in the use of polymer solutions for secondary recovery and a number of polymer floods are being performed in the United States.1 Some of these floods have become commercial while others have been reported as failures. A number of floods are still in progress and remain to be evaluated. With the advent of polymer flooding, the need developed to understand the mobility control mechanism in porous media. Rheologically, the polymer solutions behave as pseudoplastic fluids. Investigators have studied the rheology for this type of non-Newtonian fluid in porous media?-6 Results have also been reported on the ability of polymer solutions to decrease mobility.7-10 Some investigators indicated that polymer solutions show a different rheological behavior in cores than on the viscometer.7,8 This study is representative of an initiatory investigation on mobility control with polymer solutions. Some effects are considered on a qualitative basis. Mobility control is considered from the standpoint of both permeability and rheology and, to the extent possible, permeability and rheological effects are considered separately. Results show that mobility control occurs from a reduced permeability caused by polymer retention and an effective viscosity determined by the average shear rate in the core. In this respect, rheological behavior is as important in mobility control as permeability. PROCEDURES A high molecular weight, partially hydrolyzed, polyacrylamide polymer was used in the investigation. Solutions of various concentrations were made with this polymer in different types of water. Some solutions used distilled water and others used tap water. The tap water contained approximately 500 ppm dissolved solids. As used in this paper, concentrations in ppm refer to parts by weight solute to one million parts by weight of solvent. In the tap water, calcium and magnesium accounted for from 60 to 80 ppm of the solids, the remainder being mostly sodium chloride. All solutions contained a bactericide, and anti-oxidants and antiprecipitants were added to the tap water. Capillary and concentric-cylinder* viscometers determined the rheological properties of solutions. The capillary viscometer is described elsewhere.6 Berea and reservoir sandstone were used as core materials for this investigation. Cores were 1 in. in diameter by approximately 2 to 3 in. long. Prior to mounting, the Berea cores were heat-treated for 3 hours at 850F. This treatment decreased the water-sensitivity of the clays in the cores. The reservoir cores were cleaned with solvent and

By Thomas A. Read

THE internal friction of single crystals of metals is affected markedly by a variety of factors, which, according to the literature, are without influence on the internal friction of polycrystalline metals at strain amplitudes less than 10-5. For example, the internal friction of a suitably oriented zinc single crystal is multiplied by a factor of l00 when the vibration amplitude is slightly increased, and the internal friction of a copper crystal is markedly increased by the application of a stress of 30 lb. per sq. in. for one minute. In this paper it will be shown that these, together with the other phenomena associated with the damping of mechanical vibrations in metal single crystals, can be satisfactorily explained, at least qualitatively, in terms of an atomic mechanism that has been proposed for quite another purpose-that of accounting for slip in metals. The extraordinary agreement between the observed behavior of the metal single crystals and the behavior that could be predicted on the basis of this atomic mechanism leads to the belief that the latter is probably essentially correct. If this is so, it follows that valuable information about the slip process in metals may be gained from measurements of internal friction on single crystals. In this paper the results of the only study to date on the damping of mechanical vibrations in single crystals of metals will be presented. EXPERIMENTAL PROCEDURE The internal friction of a material is a measure of the rate at which the energy of mechanical vibrations is converted into heat. The measure of internal friction used in the present paper is the decrement A, which is defined as the fraction of the energy of vibration lost per half cycle. The measurements described here were .made for longitudinal oscillations at a frequency of 33.5 kc. for the copper crystals, and at a frequency of 39 kc. for the zinc crystals. The method used is that of the composite piezoelectric oscillator. The single-crystal specimens are in the form of circular cylinders ¼ in. in diameter and 1 ½ to 2 ½ in. long. The crystal rods are waxed in a V-block and sawed to the proper length with a fine jeweler's saw. The ends of the specimen are ground flat, and one end is cemented with a very thin film of beeswax and rosin to the end of an x-cut quartz rod which is ¼ in. in diameter and 3 in. long. The length of the specimen rod is determined by the condition that its natural frequency for longitudinal vibration be the same as that of the quartz rod, within 0.5 per cent. The lengths of the specimens are thus different for different orientations of the cylinder axis with respect to the crystallographic axes. When the specimen and quartz rods are thus matched in frequency the adhesive is at a node of stress, and it has been shown experimentally that under these circumstances

Jan 1, 1941

By M. G. Corson

UNTIL recently, the characteristics of cast copper have seldom been studied and such study as has been made has been inadequate. The prevailing idea seems to be that since pure copper is infrequently used in the cast state, there is no reason for trying to establish precise data regard-ing the properties of the metal in that condition. On the other hand, wrought copper either in the shape of sheets or wire rarely fails in service, except as a result of the action of reducing gases at the annealing tempera-tures, so there is little incentive to study the properties of the cast shapes -cakes, bars, ingots and billets-for-the sake of tracing the causes of failures of the wrought metal to the cast stock. However, about a decade ago, wirebars of American origin often cracked badly while being hot-rolled in mills in Germany. This led to four investigations: by E. Seidl and E. Schiebold,1 by P. Siebe,2 by O. Bauer and G. Sachs,3 and by G. Welter.4 These authors came to the conclusion that failures in hot-rolling were due essentially to the presence .of a wide zone of columnar crystals between the thin layer of fine crystals near the surfaces of the bars and the large but more nearly equiaxed grains of the central core. This macrostructural defect was explained in turn by the probable upward deviation in the temperature of the metal while it was being poured into the molds of the casting machine. More recently, cast shapes of copper were investigated by N. P. Allen5 and by C. Blazey.6 Allen examined vertically cast wirebars and hori-zontally cast wedge cakes of electrolytic tough-pitch copper, but only for the distribution of densities; i.e., porosity. Blazey was interested mainly in the mechanism of the variations in electrical conductivity clue to cold-work and anneal, but gave introductively an account of the composi-tion and average densities of the tough-pitch horizontally cast wirebars used. As far as the present writer can tell, no investigation was under-taken for the sake of presenting a picture of the distribution of mechanical characteristics in the wirebars of copper, tough-pitch or otherwise.

Jan 1, 1938

By W. C. Lacy

THE Cuajone porphyry copper deposit is the northernmost of a group of three deposits in southern Peru controlled by the Southern Peru Copper Corp.-Toquepala, Quelleveco, and Cuajone— all within a 20-mile belt. Although small pockets of high-grade copper oxide ores were worked in the Cuajone area in the 19th century, it was not until 1939 that its potentialities as a disseminated deposit were recognized by 0. C. Schmedeman. An exploratory drilling pro- gram was begun in December 1942 and continued until early 1945. The program was revived in November 1952 and completed early in 1954. Early exploration was by diamond drilling. Later exploration was predominantly churn drilling, with diamond drilling used only for wildcat holes. Along this northwest-trending belt of deposits. which follows the western slopes of the Andean Range, quartz-monzonite has invaded earlier dio-rite intrusives and a series of warped and tilted Cretaceous volcanic flows. Little faulting of consequence has been recognized within the mineralized areas. Sulfide minerals were introduced into all these diverse rocks, and mineralization was followed by erosion, oxidation, and enrichment. In Late Tertiary and/or Quaternary time the entire

Jan 1, 1959

As one surveys the extensive taconite operations on the Mesabi Range, he may find it difficult to believe that only 15 years ago, the iron ore mining industry here was staring at its own imminent demise. Due to the high demands for iron ore during World War II the postwar period of 1946-1950, and the subsequent "police action" in Korea, there was rapid consumption of the Mesabi's already depleted ores, and some economists were giving the Range only 20-25 years of life. In the 13-year period 1941-1953, more than 850 million tons of iron ore were shipped to steel mills, an amount almost equal to the total production during the preceding 30 years. Proven ore reserves dropped from 1.1 billion tons in 1940 to 8.3 million tons in 1954, the largest decrease being recorded in the famed direct shipping ores.

Jan 9, 1968

By Edwin Ludlow

ONE of the most unusual features in connection with the strike of the union coal miners in the bituminous fields, now in its sixth week, is that the public interest seems to have completely died out. There is nothing on the front page and very little on any other page of the daily newspapers in connection with the strike. The United Mine Workers' officials must be rather disappointed to find that the only way in which they are being featured in the papers at present is in the reports of the trial for treason that is going on in Charlestown, West Va., against the local leaders of that organization for their responsibility in connection with the attack of the miners' army last summer against the non-union mines of Logan and Mingo Counties. Recent reports state that there are 13,000 cars of coal standing on the sidings at union mines for which no billing has yet been found. The output of the non-union mines has been gradually increasing but has never reached the maximum that they are capable of producing, owing to their inability to obtain enough orders to make it possible to run full operating time. The, present output is estimated at, 4,500,000 tons a week. It is possible, with a full car supply and full demand, to bring this output up to approximately 6,000,000 tons per week, and it is very doubtful whether, at this season of the year when probably there is less consumption of coal than, at any other season, the requirements of the country are greater than the 6,000,000 tons which the non-union mines are capable of producing. It would appear, therefore, that there is no immediate prospect of any settlement of the bituminous strike, and there is certainly no reason why the operators of the union mines should show any anxiety to begin operations as long as they have unbilled coal standing on their sidings.

Jan 6, 1922

By Charles S. Barrett, Hermann F. Kaiser, Robert F. Mehl

THE copper-silver system presents several points of special interest in the study of segregate structures. The system is simple eutectic, with limited solid solutions terminal with the pure component metals. The extent of solid solubility decreases with decreasing temperature for both the copper-rich and the silver-rich alloys, thus offering a possibility for the formation of Widmanstätten figures and also a possibility for aging after quenching. In contrast to the structures studied previously the structures in this system are unique in their origin, for one terminal solid solution will precipitate the other, and vice versa. In most of the other systems for which crystallographic data on the precipitation (or transformation) process are available, either intermetallic compounds or intermediate phases partake in the decomposition process; the absence of such phases thus distinguishes this system. The lattice structures of the two solid solutions are identical in type, differing in lattice spacing by approximately 10 per cent; because of this it seems difficult if not impossible to predict on the basis of present theory either the outward form of the precipitate or the lattice orientation relationships between matrix and precipitate. The eutectic temperature in the copper-silver system1 is 779° C. At this temperature copper dissolves 4.3 atomic per cent (7.0 weight per

Jan 1, 1935

By Leo Tarasov

MAGNETIC torque studies of ferromagnetic single crystals have been carried out in a number of laboratories during the last decade1,2 and some work has been reported on polycrystalline material showing preferred orientation. Goss3 used the method extensively in developing electrical sheet with desirable magnetic properties, but he used it as a control rather than as a means of studying the texture. Bozorth4 made a quantitative correlation of a torque curve he obtained from some cold-rolled iron with the texture as determined from X-rays, but did not extend his studies beyond the one specimen. Other studies, which have been reported from time to time 1.5 have also been incomplete in the sense that no effort was made to study a whole series of samples, differing only in degree of cold reduction, or in the annealing temperature, in order to ascertain the effect of such treatments on the texture as revealed by torque measurements. It is the purpose of this investigation to make such a study, mainly in order to see how useful the method can be made when used under favorable circumstances and to find what kind of a correlation can be expected between magnetic and X-ray studies of texture. Before proceeding further, it is desirable to say a little about single crystals, so as to make clear the concepts involved in magnetic torque measurements.

Jan 1, 1939

By E. M. Norris

During the winter and spring of 1917, an unprecedented number of underground fires occurred in the Butte district. With one exception, these fires were caused by the failure of electrical equipment, and called attention to the increased fire hazard in underground mining operations occasioned by the extensive use of electricity. Five local conditions that contributed toward a heavy fire risk were: (1) The heavy continuous timbering necessary for mine supports; (2) the strong ventilating pressures in the shafts and main airways; (3) the subsidence and faulting movements in the country rock, which ruptured cables and displaced trolley and lighting wires; (4) the strongly acid mine waters, which quickly developed any weak points in the electrical insulation; (5) oxidation in old stopes containing large amounts of timber. In the summer of 1917, a comprehensive plan of fire prevention was begun by the Anaconda Copper Mining Co., which involved a thorough and intensive development of the preventive measures then in use. These were as follows: Fireproofing, remodeling and strengthening electrical insulations, extension of underground water system, control of ' ventilation, maintaining efficiency of fire-fighting crews, and reorganization of fire patrol. In considering the problems of fireproofing, it was immediately apparent that some method of applying a durable coat of fireproof material to the mine timbers was needed. The first experiments were made with a plaster composed of one part cement, one-half part fireclay, and three parts sand. This was applied by hand to a thickness of 1 in. (2.5 cm.) over a reenforcement of herringbone metal lath. It made a very satisfactory covering for fan stations, but was too soft and friable for traveling ways, where it was subject to abrasion. The cement gun was tried next with a three to one mixture of sand and cement. A 1/2-in. coating of gunite applied over poultry netting or metal-lath reenforcement proved

Jan 1, 1923

By E. M. Norris

During the winter and spring of 1917, an unprecedented number of underground fires occurred in the Butte district. With one exception, these fires were caused by the failure of electrical equipment, and called attention to the increased fire hazard in underground mining operations occasioned by the extensive use of electricity. Five local conditions that contributed toward a heavy fire risk were: (1) The heavy continuous timbering necessary for mine supports; (2) the strong ventilating pressures in the shafts and main airways; (3) the subsidence and faulting movements in the country rock, which ruptured cables and displaced trolley and lighting wires; (4) the strongly acid mine waters, which quickly developed any weak points in the electrical insulation; (5) oxidation in old stopes containing large amounts of timber. In the summer of 1917, a comprehensive plan of fire prevention was begun by the Anaconda Copper Mining Co., which involved a thorough and intensive development of the preventive measures then in use. These were as follows: Fireproofing, remodeling and strengthening electrical insulations, extension of underground water system, control of ' ventilation, maintaining efficiency of fire-fighting crews, and reorganization of fire patrol. In considering the problems of fireproofing, it was immediately apparent that some method of applying a durable coat of fireproof material to the mine timbers was needed. The first experiments were made with a plaster composed of one part cement, one-half part fireclay, and three parts sand. This was applied by hand to a thickness of 1 in. (2.5 cm.) over a reenforcement of herringbone metal lath. It made a very satisfactory covering for fan stations, but was too soft and friable for traveling ways, where it was subject to abrasion. The cement gun was tried next with a three to one mixture of sand and cement. A 1/2-in. coating of gunite applied over poultry netting or metal-lath reenforcement proved

Jan 1, 1923

By W. F. Holbrook, C. E. Wood, E. P. Barrett

The high-frequency laboratory induction furnace with a rotating liquid crucible enables research workers to conduct certain investigations heretofore very difficult or impossible to realize because vessels are not obtainable that are capable of resisting the physical conditions or the chemical actions to which they are subjected. Applications for patents covering commercial uses of centrifugal liquid crucibles were filed in the United States in 1919,' in France in 1925, in the United States and Germany in 1926,2 and in France in 1927.3 In 1928, Schuette and Maier,4 of the Bureau of Mines, reported the construction of a whirling table beneath a high-frequency induction furnace. Shape and Size of Centrifugal Liquid Crucibles When a vessel containing a liquid is rotated, the inner surface of the liquid takes the shape of a paraboloid under the simultaneous action of centrifugal force and gravity. The internal dimensions of the paraboloid rotating liquid crucible are governed by the diameter of the container and its speed of rotation. Melted Wood's metal was poured into cylinders 2 1/2 in. in diameter, which were rotated at 180, 300, and 468 r.p.m. When the metal was solid, a slurry of plaster of Paris was added, and rotation continued until the plaster had set. Fig. 1, a photograph of sections of the cylinders, shows the effect of speed of rotation of the containers upon the shape of the inner surface of the rotating liquid crucibles. Types of Furnaces Three types of high-frequency induction laboratory furnaces using liquid-metal crucibles were designed and constructed by the Blast

Jan 1, 1939