Search Documents

By A. H. Geisler

INTRODUCTION THE correlation of property changes during precipitation with structure has progressed, sometimes rapidly but other times more slowly, since the fundamental discovery of Merica, Waltenberg and Scott.1 The predominent factor that hampered the progress has been limitations imposed by the various detection methods. Refinements in X ray diffraction techniques and in metallographic methods, which have been extended by the electron microscope, have contributed new information within the last few years. These permit an extension of the theory as proposed by Mehl and fetter in 1940.2 Now that a suffcient number of alloys has been investigated to establish a general mechanism of the precipitation process, a correlation of the facts into a generally applicable theory of age-hardening is both warranted and desirable. 'I he purpose of the paper is to provide an orderly correlation of the phenomenological facts of precipitation hardening. Speculation on mechanism of hardening will be confined to that consistent with existing theories of hardening. Age-hardening accompanies the formation of a new structure, the precipitate, as provided by an alloy system in which solid solubility decreases with decreasing temperature. Upon this premise alone all such systems would be expected to include age-hardenable alloys. Alas, this is not always the case. Few attempts have been made to explain the variable degree of age-hardening among different alloys or to explain the influence of small alloying additions upon the hardening. Dispersion hardening as originally postulated3 is not adequate.* Coherency hardening-the term that will be used to distinguish the properties of a two-phase mixture in the unique and unstable transition state at which the phases are strained into precise atomic registry (continuity or coherency) in planes

Jan 1, 1948

By H. J. Struth

Gasoline is undoubtedly of major importance not only to the petroleum refiner but to the producer. To study the economic aspects of gasoline is, in a measure, a constructive effort to solve the problem of overproduction not only for the refiner but for the entire petroleum industry. After all, the prime object of producing crude petroleum is to supply motor fuel and lubricants to nearly 25,000,000 American motor vehicles, not to mention the increasing demand for these products abroad. Since gasoline furnishes the chief source of revenue to the refiner, it follows that this important product should veritably become recognized by all branches of the petroleum industry as an almost infallible index of day to day requirements of the producer and the refiner. A careful study of gasoline statistics over the past decade or more reveals that there is a definite correlation between world-wide gasoline requirements and the demand for crude petroleum, as well as all other petroleum products. This leads the writer to the conclusion that gasoline is literally the economic yardstick of the entire petroleum industry. Control of Operations That the refiner has begun to recognize the urgent need for controlling his operations is evidenced by the results of the past three years. Unfortunately, it is a difficult problem to convince the refiner that he cannot run crude in excess of the demand for gasoline, without incurring a consequent decline in the market value of this and all other products of distillation. Undoubtedly, he still has much to learn in this respect. Few commercial products have enjoyed such phenomenal growth in demand as has gasoline, and, at the same time, few products have failed, as has gasoline, to reap financial benefit from the popular demand for a national necessity. Perhaps this unprecedented demand was responsible for the overextension of retining facilities, which resulted in the excesses of recent times; at any rate, as the demand for gasoline grew by leaps and bounds, so the refining industry continued to increase its capacity for

Jan 1, 1929

By Cecil Desch

THIS annual lecture, under the auspices of the Institute of Metals Division, and which was illus- trated by lantern slides, has been printed in full and a limited number are available for distribution on request. Some excerpts from the lecture are given below: Ever since the simple geometrical relations of crystals were discovered, it has been recognized that their proper-ties are best explained by assuming that their ultimate particles are arranged on a space lattice, and that the char-acteristics of that lattice determine the shape of the crystal and its physical and mechanical properties. Modern ex-amination by means of X-rays has widened that concep-tion and given it greater; definiteness, and the atoms are now regarded as the particles forming the space lattice. The splendid achievements of investigators in this field have made it possible to state, for a large number of sub-stances, the form and dimensions of the lattice. The char-acteristic of a lattice is that a unit of simple geometrical form is repeated at regular intervals in three dimensions so as to fill the entire crystal. It follows that there must be certain planes in which the atoms are more closely packed than in planes drawn at any angle to them, and it is these planes of closest packing which play the greatest part in determining the growth and other properties of the crystal. There are actually two stages in crystallization, what-ever be the medium in which it occurs. The first is the ap-pearance of crystal nuclei; the second the growth of those nuclei to form crystals of appreciable .size. The first is clearly a kinetic phenomenon. In the molten mass, solu-tion, or vapor, the molecules are in a state of rapid motion and frequent collision. When the temperature has fallen so far. that it is possible for a crystal to exist, a few col-liding molecules may fail to rebound, and so become at-tached to one another, the balance between the attracting and repelling forces-between them causing them to arrange themselves on a space lattice, to which other molecules sub-sequently attach themselves. It was once maintained that the X-ray evidence demanded that the molecule should dis-appear in the solid crystal, but this was a wrong inference, and in many crystals, but not in all, the chemical molecule retains its identity in the solid state. In pure metals the atom and the molecule are identical, so that the conditions are unusually simple. How many. nuclei will be formed in a given mass is evi-dently a problem in probability. Experiments to deter-mine the relation between the temperature and the number of nuclei formed in a given time have been made with some success by using viscous organic substances, but metals offer much greater difficulties, and the few determinations which have been published are vitiated by serious errors. However, the examination of sections of ingots of the same composition and cast at 'the same temperature in similar molds will show, that the number of crystals does not vary widely.

Jan 3, 1927

By Stanley W. Sundeen

2.3-1. Introduction. The subject-"Preliminary Evaluation of Coal, Metallic and Industrial Mineral Deposits for Surface Mining'-seems at first glance to be definitive and not likely to be misinterpreted. Nevertheless, there are widely divergent opinions as to what is meant by "preliminary" and even as to what is meant by "evaluation." Some definition and qualification is necessary in order to provide a readily recognized basis for discussion. Evaluation evokes the idea of organizing extant data and judging its significance especially in the economic sense. It also may evoke the concept of the physical processes of acquiring the data that will characterize the deposit such as the geologic mapping, drilling, etc. Castle (5) considers that evaluation may embrace psychological aspects wherein human traits as, for example, over optimism might cause the evaluator to overlook obvious project weaknesses. In this chapter, evaluation is discussed primarily from the viewpoint of economically appraising a project from data available at a given point in time. The qualifying adjective "preliminary" is not easily defineable. In fact, some kind of evaluation proceeds, if not continuously, intermittently over the full span of exploration and early stages of development of a deposit. Bailly (1) comments: "Sometimes, before starting exploration in new areas or countries for a given commodity, we establish models to define what minimum combinations of re- coverable grade and tonnage are needed to give the minimum acceptable rate of return established by corporate policy. Then, before starting physical exploration in any target area we try and guesstimate optimistically what best 'geometry-grade-tonnage' can be expected. If these are acceptable in light of above minimum combinations, exploration is started as soon as funds are appropriated for the target area.''

Jan 1, 1968

By H. W. Graham

THE young metallurgist of today who thinks casually of the technical literature of the steel industry might conclude that little has been published concerning the Bessemer process. This conclusion is true as relating to the last decade or two, but there is a fairly voluminous Bessemer literature in the period of 1860 to 1910, Since that time, however, an entirely new level of metal-lurgical knowledge of steelmaking has been reached; and the present paper is simply an effort to look broadly from this new level and to bring the recorded history of the process up to date, It is an effort to appraise the acid Bessemer method of steelmaking in the light of today's technical knowledge thereof. In this paper matters of history will be dealt with only insofar as they contribute to an understanding of today's situation. Attention will be directed to the apparent causes of past developments in seeking to perceive the true direction of trends now in existence and effective as bearing upon future developments. The paper will discuss the economics of the Bessemer process, but only to the extent that will bear upon the metallurgist's understanding of his respon-sibility. The problem of the quality of Bes-semer steel will be reviewed and examples will be given of the technical data upon which the reasoning of the paper is based, Matters of engineering design, mechanical maintenance, operation and metallurgical investigation will be surveyed. Compari-sons will be made between the Bessemer and open-hearth processes for the sake of clear and ready understanding,

Jan 1, 1940

By E. J. Wasp, N. T. Cowper, R. A. Davis, W. F. McDermott

On October 26, 1967, the world's first long distance iron ore slurry line was put into service by Savage River Mines. The commissioning of this $5 million installation climaxed three years of development, testing, and construction. The mine and concentrator are located approximately 30 miles from the town of Waratah in a rugged semi-mountainous terrain. The open pit mine will produce approximately 5 million long tons a year of crude ore, which is ground in autogenous mills, separated magnetically, thickened and prepared for the pipeline. The 53-mile pipeline transports the 2,250,000 tons of concentrate north to Port Latta. The Port Latta facilities include the receiving, storage and thickening equipment for the slurry as well as filtering, balling and pelletizing equipment to produce the 2,250,000 tons of high grade iron ore pellets. Five vertical shaft furnaces are used for pelletizing.

Jan 1, 1969

By T. L. Joseph

LARGE deposits of manganiferous iron ores, representing several million tons of metallic manganese, occur in the United States. The Minnesota deposits of such ore-are of outstanding importance because of their size, state of development, ease of mining and proximity to the Great Lakes, which permits water transportation to steel centers. In' view of the fact that our steel industry requires large quantities of manganese, for which no satisfactory substitute-has been found, and because our reserves of ferro-grade ore are comparatively small, the development of methods that will make our large deposits of manganiferous iron ores available as a source of ferromanganese is an important problem. Realizing the importance of this problem, some years ago the North Central Station of the U. S. Bureau of Mines and the Minnesota School of Mines Experiment Station undertook jointly the development of methods for recovering the manganese content of manganiferous iron ores in a: form suitable for the production of ferromanganese, the 80 per cent. alloy indispensable in producing steel. Two types of manganiferous iron ores have been described in previous reports. I The brown ores are higher in iron and lower in manganese than the black ores; the black ores are more siliceous but contain less phosphorus. The utilization of the iron content of the brown ores in the production of steel appears to furnish the best basis for their treat-ment. The method of attack has been to work out modifications in iron and steel practice so as to recover manganese in the form of slag comparable to ferro-grade ores. The greater part of the experimental work has been conducted with a 6-ton blast furnace and a Y2-ton basic open hearth. This paper is devoted mainly to open-hearth tests in which high-phosphorus spiegel

Jan 1, 1930

FRIENDS of the late Charles F. Rand presented in 1930 a sum of money from which the income is available to support various phases of the work of the Institute in which Mr. Rand was so deeply interested. At present the fund amounts to $10,400. The specific terms of the deed of gift are as follows: "The fund collected to establish a memorial to the late Charles F. Rand shall be placed in the custody of the Board of Directors of the American Institute of Mining and Metallurgical Engineers, to be set up as a trust to be known as the `Charles F. Rand Foundation,' the income of which shall each year be applied to a distinct purpose to be decided upon in that year by vote of the Board of Directors. This purpose shall be such as to promote the general welfare of the Institute and to constitute a permanent memorial of the usefulness of Mr. Rand, who for many years gave unstintingly of his time and talents in its service. "It shall be within the discretion of the Board of Directors to establish a medal to be known as the Charles F. Rand Memorial Medal to be awarded at such a time and under such rules as may be determined by the Board of Directors, for Distinguished Achievement in Mining Administration." The establishment of this medal was announced at the annual meeting in February, 1932, the term "mining" being defined in its broad sense to include metallurgy and petroleum. Robert Linton is chairman of the Charles F. Rand Foundation Award Committee.

Jan 1, 1943

By William Kent

Mr. ASHBURNER's paper on the Classification and Composition of Pennsylvania Anthracites, read at this meeting, well shows the need of new and accurate determinations of the heating value of these coals. A similar need exists for the determination of the value of bituminous coals, since the variation in quality of the latter is greater than the variation in anthracites. The recent extensive use of liquid and gaseous fuels, " patent" fuels, tan-bark, and other refuse fuels, also makes a necessity fix some correct method of determining the relative values of each of these fuels. Mr. Ashburner has recommended that tests of coals should be undertaken by the Second Geological Survey of Pennsylvania, and Professor Dewey, as stated in Mr. Ashbnrner's paper, has suggested a plan for tests of American coals, by the Smithsonian Institution, for which an appropriation by Congress will be asked. It is to be hoped that if any extensive series of tests of coals is carried on under either Government or State auspices, the erroneous methods of test which were followed by Professor Johnson in 1842, and by Quartermaster-General Meigs in 1882, will not be adopted.* The first requisite in determining the heating-power of a fuel is proper apparatus, such as has not been used in any of the tests of American coals yet reported. In the hope that more accurate means may be used in future tests, the writer desires to call attention to an apparatus which he has designed for the purpose. Not having had opportunity for making a trial of it, nor even of having it criticised by others, he does not offer it as the best possible apparatus; but if it contains any points of value, and leads to the design of still more suitable devices by others, the object of the presentation of this paper will be accomplished. The tests by Professor Johnson and General Meigs were made by evaporating water into steam in ordinary steam-boilers. A steamboiler of ordinary construction is not a good apparatus for determining the heating power of a fuel, for the following reasons:

Jan 1, 1886

By Stanley Herold

A FEW notes on the occurrence and significance of mud volcanoes in Colombia may be of interest at the present time, owing to the renewed activity in geological exploration of, the coastal regions bordering the Caribbean Sea. The best-known volcanoes are found a few miles from the seacoast. One is situated to the south of Puerto Colombia; the second, to the east: of Cartagena near the village of Turbaco; and the third, near the village of Puerto Escondido south of the Sinu River. Others. are reported in more inaccessible localities. Usually they stand 2 1/2 or 3 ft. (0.762 or 0.914 m.) above the surrounding ground at the crater, though several craters from 10 to 20 ft. (3.04 to 6.09 m.,) apart will often build up an extensive mound at low gradient. The shallow mound may cover 1/2 or 3/4 acre (0.2 to 0.3 ha.) with an elevation of 12 or 15 ft. (3.65 or 4.57 m.) at the center. The craters are formed of hardened blue clay; the inside diameters vary from 14 to 24 in. (35.56 to 60.96 cm.). The rim is continuous, except on one side where there is usually a cut 3 or 4 in. deep, thus allowing an overflow. The craters are filled to the rim-cut- with a thick mixture of blue clay mud and water, which is kept in agitation by escaping gas. Fig. 1 shows the bubble in the act of bursting and Fig. 2 the appearance of the surface of the viscous fluid a second or so later. The frequency of the explosions is determined by the weight of the column of fluid in the neck of the volcano, consequently, such explosions are not synchronous in a group of craters. Ordinarily, there are two or three explosions in about 3' minutes. The supply of gas is small but steady and sufficient pressure must accumulate before the bubble can enter the column of fluid. The water is derived from the surface and enters the sedimentary strata not` far distant from the volcano. During long dry seasons, as the supply of water fails the volcano dries and geyser action ceases.

Jan 7, 1919

By R. P. Carreker, R. W. Guard

True stress-true strain data are given for nominally pure molybdenum (99.95 pct) over the temperature range -196° to 1540°C (0.027 to 0.63 T/T). Strain rate sensitivity was determined by rate change tests and stress relaxation tests. Inhomogeneous yielding and strain aging effects were observed. The yield stress and tensile strength depend markedly on temperature below 400°C and are insensitive to temperature in the range 400' to 800°C. The ductile to brittle transition range is +25O to -25OC. Strain rate sensitivity and stress relaxation effects are very large near room temperature. THIS report presents data which were obtained as a part of a continuing program designed to document the deformation behavior of nominally pure metals over a wide temperature range.'" This research program is rooted in the conviction that sufficient tensile and creep data of appropriate quality and detail does not exist to provide precise phe-nomenological descriptions of the deformation behavior of pure metals as a function of temperature, strain rate, and grain size. Such knowledge is needed to provide a firm base for alloy design and an experimental framework to which theories of deformation must conform. These data also complement a parallel exploratory program investigating the properties of refractory metals, including molybdenum, and their alloys. Several important reviews and research reports dealing with the tensile properties of molybdenum as a function of temperature have appeared."-lo To a great extent the work to be reported in the present paper parallels that of Bechtold and of Pugh. The authors' results are in general agreement with those of Bechtold and Pugh. The principle differences be- tween the present experiments and those published previously are as follows: 1—Wire specimens prepared from arc cast molybdenum were used in the present experiments, bar specimens were used by others. Pugh used arc cast material while Bechtold's most extensive results" were obtained on powder metallurgy specimens. 2—Several different grain sizes were tested in the present experiments. 3—The testing range was extended to cover from -196°C to 1570°C (0.027 to 0.63 T/Tm). 4—The combination of wire specimens, high speed autographic recording, and a stiff testing machine permitted more detailed study of initial yielding. The principle contribution of the present paper is the demonstration of the relatively consistent mechanical properties of nominally pure arc cast molybdenum specimens of differing metallurgical history. Bechtold and Scotts have shown that arc cast and powder metallurgy molybdenum samples have comparable tensile properties in the range —75" to 200°C when processed to have the same re-crystallized grain size. Material The molybdenum used in this investigation was supplied by the Climax Molybdenum CO. Its metallurgical history is outlined in Table I; the final products were 0,030 in, diam wire specimens annealed at 1100' and 1375°C and 0.060 in. diam wire

Jan 1, 1957

By H. T. Clark, S. Feigenbaum

The importance of measuring the temperature of molten steel in the open-hearth furnace has been recognized for many years. Poor temperature control may be costly to steelmaking operations and lead to a lowered quality of the steel. Low or excessive temperatures may shorten the life of the furnace, ladles and molds. Rates of reactions in the furnace and efficiencies of deoxidizers are known to change materially with a change in the temperature of the metal and slag. Ladle skulls and mold and stool stickers cause steel to be scrapped instead of being converted into useful products. Finally, the structure, segregation and surface condition of ingots are affected by the teeming temperature. Mill investigations of the effect of bath temperature upon steelmaking operations have been largely qualitative in character, based upon observations by practical melting men. The physical chemist has used the empirical information available and has reached reasonable and useful conclusions with respect to the various melting processes. The introduction of a reliable direct-reading pyrometer will permit accurate quantitative evaluation of the effects of temperature and should furnish a more rational basis for study of the thermochemistry of steelmaking. The problem is not merely one of making a small numbcr of temperature measurements in the open-hearth furnace. This has been done by several methods to a * Assistant Manager, Research and Development, Jones and Laughlin Steel Corporation, Pittsburgh, Pennsylvania. Issued as T.P. 2031 in MEtals Technology, June 1946; also in Open Hearth Proc., 1946. † Open-hearth Metallurgist, Jones and 1aughlin Steel Corporation, Aliquippa. Pennsylvania. degree of precision that was apparently satisfactory. Considerable effort by a number of investigators has been directed rather to the development of an open-hearth bath pyrometer that would be both accurate and practical for routine measurements. To be practical, the pyrometer should be inexpensive to operate; that is, the installation, operating and maintenance costs should be exceeded by the tangible benefits to the open-hearth operator. Temperatures from 2800' to 3100°F. are. encountered in the open-hearth furnace. The surface of the molten metal is covered by several inches of slag, which prevents direct observation of the metal surface for optical or radiation measurements. Both slag and metal are highly reactive at these temperatures and will attack to a greater or lesser extent any material immersed in them. Adequate protectioil of thermocouples, which of necessity must be brought to the temperature of the bath, has generally resulted in a large, heavy assembly made up of brittle materials, unsuited for handling on the open-hearth floor. The life of the equipment was short and maintenance was an important consideration. Earlier Work Any of a number of Physical Properties of liquid steel could conceivably be used a a basis for temperature measurement. Efforts to the present time, however, have been confined largely to measuring either the thermal electromotive force generated between two dissimilar materials immersed in the steel or the intensity of radiation from the surface of the steel. These

Jan 1, 1947

By H. T. Clark, S. Feigenbaum

The importance of measuring the temperature of molten steel in the open-hearth furnace has been recognized for many years. Poor temperature control may be costly to steelmaking operations and lead to a lowered quality of the steel. Low or excessive temperatures may shorten the life of the furnace, ladles and molds. Rates of reactions in the furnace and efficiencies of deoxidizers are known to change materially with a change in the temperature of the metal and slag. Ladle skulls and mold and stool stickers cause steel to be scrapped instead of being converted into useful products. Finally, the structure, segregation and surface condition of ingots are affected by the teeming temperature. Mill investigations of the effect of bath temperature upon steelmaking operations have been largely qualitative in character, based upon observations by practical melting men. The physical chemist has used the empirical information available and has reached reasonable and useful conclusions with respect to the various melting processes. The introduction of a reliable direct-reading pyrometer will permit accurate quantitative evaluation of the effects of temperature and should furnish a more rational basis for study of the thermochemistry of steelmaking. The problem is not merely one of making a small numbcr of temperature measurements in the open-hearth furnace. This has been done by several methods to a * Assistant Manager, Research and Development, Jones and Laughlin Steel Corporation, Pittsburgh, Pennsylvania. Issued as T.P. 2031 in MEtals Technology, June 1946; also in Open Hearth Proc., 1946. † Open-hearth Metallurgist, Jones and 1aughlin Steel Corporation, Aliquippa. Pennsylvania. degree of precision that was apparently satisfactory. Considerable effort by a number of investigators has been directed rather to the development of an open-hearth bath pyrometer that would be both accurate and practical for routine measurements. To be practical, the pyrometer should be inexpensive to operate; that is, the installation, operating and maintenance costs should be exceeded by the tangible benefits to the open-hearth operator. Temperatures from 2800' to 3100°F. are. encountered in the open-hearth furnace. The surface of the molten metal is covered by several inches of slag, which prevents direct observation of the metal surface for optical or radiation measurements. Both slag and metal are highly reactive at these temperatures and will attack to a greater or lesser extent any material immersed in them. Adequate protectioil of thermocouples, which of necessity must be brought to the temperature of the bath, has generally resulted in a large, heavy assembly made up of brittle materials, unsuited for handling on the open-hearth floor. The life of the equipment was short and maintenance was an important consideration. Earlier Work Any of a number of Physical Properties of liquid steel could conceivably be used a a basis for temperature measurement. Efforts to the present time, however, have been confined largely to measuring either the thermal electromotive force generated between two dissimilar materials immersed in the steel or the intensity of radiation from the surface of the steel. These

Jan 1, 1947

By C. E. Berry

Natural stone or manufactured porcelain pebbles are used as the grinding elements in pebble mills and the mills are lined with stone or porcelain blocks. Steel balls usually form the grinding medium in ball mills, and the mills may be lined with steel. Pebble mills are used to avoid contamination by metal of the material being ground, to avoid rapid wear due to corrosion, and for other specialized reasons. Belgian silex (silica) blocks formerly were used widely for lining pebble mills, because of their good resistance to wear, light color, and low cost, but the importation of these blocks was suspended early in the war. The stocks of Belgian silex diminished so rapidly that it was found desirable to compare the properties of a number of domestic substitutes for use in critical operations. Accordingly, a study was made to determine the best substitutes for fine grinding of white pigment and for certain heavy-chemical process work such as the disintegration of phosphate rock in weak phosphoric acid solution. A comprehensive survey of substitute lining materials was not contemplated. It was stipulated at the beginning of the investigation that only materials on the market, available in large quantities, would be tested and that these should be reasonable substitutes from a a ance viewpoint as determined from known physical characteristics. Marble and limestone, for example, could be eliminated immediately. Quartzite, granite and porcelain were selected as likely substitutes for Belgian silex and were subjected to quality tests. Materials Tested 1. Belgian Si1ex.—Sample blocks of a standard grade were taken from crates in which they had been imported. The stone was light gray in color and contained inclusions of small clusters of quartz crystals as well as light colored portions that might be calcite. This was a siliceous rock which appeared to be of igneous origin. 2. Quartzite.—Samples of quartzite were obtained from a quarry in Minnesota. The blocks exhibited a crystalline fracture. The stone was pink in color and composed of fine quartz crystals bound together with a siliceous cement. 3. Granite A was a fine-grained granite quarried in South Carolina. 4. Granite B was coarse-grained granite quarried in South Carolina. 5. Granite C was a coarse-grained granite quarried in North Carolina. 6. Porcelain A.—Sample blocks of the pebble-mill lining material were obtained direct from the manufacturer. It was white in color and of lower specific gravity than the natural materials. It did not have a crystalline structure. 7. Porcelain B.—Sample pebble-mill lining blocks of the porcelain were received direct from the manufacturer. It was white

Jan 1, 1948

By C. E. Berry

Natural stone or manufactured porcelain pebbles are used as the grinding elements in pebble mills and the mills are lined with stone or porcelain blocks. Steel balls usually form the grinding medium in ball mills, and the mills may be lined with steel. Pebble mills are used to avoid contamination by metal of the material being ground, to avoid rapid wear due to corrosion, and for other specialized reasons. Belgian silex (silica) blocks formerly were used widely for lining pebble mills, because of their good resistance to wear, light color, and low cost, but the importation of these blocks was suspended early in the war. The stocks of Belgian silex diminished so rapidly that it was found desirable to compare the properties of a number of domestic substitutes for use in critical operations. Accordingly, a study was made to determine the best substitutes for fine grinding of white pigment and for certain heavy-chemical process work such as the disintegration of phosphate rock in weak phosphoric acid solution. A comprehensive survey of substitute lining materials was not contemplated. It was stipulated at the beginning of the investigation that only materials on the market, available in large quantities, would be tested and that these should be reasonable substitutes from a wear-resistance viewpoint as determined from known physical characteristics. Marble and limestone, for example, could be eliminated immediately. Quartzite, granite and porcelain were selected as likely substitutes for Belgian silex and were subjected to quality tests. Materials Tested 1. Belgian Si1ex.—Sample blocks of a standard grade were taken from crates in which they had been imported. The stone was light gray in color and contained inclusions of small clusters of quartz crystals as well as light colored portions that might be calcite. This was a siliceous rock which appeared to be of igneous origin. 2. Quartzite.—Samples of quartzite were obtained from a quarry in Minnesota. The blocks exhibited a crystalline fracture. The stone was pink in color and composed of fine quartz crystals bound together with a siliceous cement. 3. Granite A was a fine-grained granite quarried in South Carolina. 4. Granite B was coarse-grained granite quarried in South Carolina. 5. Granite C was a coarse-grained granite quarried in North Carolina. 6. Porcelain A.—Sample blocks of the pebble-mill lining material were obtained direct from the manufacturer. It was white in color and of lower specific gravity than the natural materials. It did not have a crystalline structure. 7. Porcelain B.—Sample pebble-mill lining blocks of the porcelain were received direct from the manufacturer. It was white

Jan 1, 1947

By C. E. Berry

NATURAL stone or manufactured porcelain pebbles are used as the grinding elements in pebble mills and the mills are lined with stone or porcelain blocks. Steel balls usually form the grinding medium in ball mills, and the mills may he lined with steel. Pebble mills are used to avoid contamination by metal of the material being ground, to avoid rapid wear due to corrosion, and for other specialized reasons. Belgian silex (silica) blocks formerly were used widely for lining pebble mills, because of their good resistance to wear, light color, and low cost, but the importation of these blocks was suspended early in the war. The stocks of Belgian silex diminished so rapidly that it was found desirable to compare the properties of a number of domestic substitutes for use in critical operations. Accordingly, a study was made to determine the best substitutes for fine grinding of white pigment and for certain heavy-chemical process work such as the disintegration of phosphate rock in weak phosphoric acid solution. A comprehensive survey of substitute lining materials was not contemplated. It was stipulated at the beginning of the investigation that only materials on the market, available in large quantities, would be tested and that these should be reasonable substitutes from a wear-resistance viewpoint as determined from known physical characteristics. Marble and limestone, for example, could be eliminated immediately. Quartzite, granite and porcelain were selected as likely substitutes for Belgian silex and were subjected to quality tests. MATERIALS TESTED I. Belgian Silex.-Sample blocks of a standard grade were taken from crates in which they had been imported. The stone was light gray in color and contained inclusions of small clusters of quartz crystals as well as light colored portions that might be calcite. This was a siliceous rock which appeared to be of igneous origin. 2. Quartzite.-Samples of quartzite were obtained from a quarry in Minnesota. The blocks exhibited a crystalline fracture. The stone was pink in color and composed of fine quartz crystals bound together with a siliceous cement. 3. Granite A was a fine-grained granite quarried in South Carolina. 4. Granite B was coarse-grained granite quarried in South Carolina. 5. Granite C was a coarse-grained granite quarried in North Carolina. 6. Porcelain A.-Sample blocks of the pebble-mill lining material were obtained direct from the manufacturer. It was white in color and of lower specific gravity than the natural materials. It did not have a crystalline structure. 7. Porcelain B.-Sample pebble-mill lining blocks of the porcelain were received direct from the manufacturer. It was white

Jan 1, 1946

By C. E. Berry

Natural stone or manufactured porcelain pebbles are used as the grinding elements in pebble mills and the mills are lined with stone or porcelain blocks. Steel balls usually form the grinding medium in ball mills, and the mills may be lined with steel. Pebble mills are used to avoid contamination by metal of the material being ground, to avoid rapid wear due to corrosion, and for other specialized reasons. Belgian silex (silica) blocks formerly were used widely for lining pebble mills, because of their good resistance to wear, light color, and low cost, but the importation of these blocks was suspended early in the war. The stocks of Belgian silex diminished so rapidly that it was found desirable to compare the properties of a number of domestic substitutes for use in critical operations. Accordingly, a study was made to determine the best substitutes for fine grinding of white pigment and for certain heavy-chemical process work such as the disintegration of phosphate rock in weak phosphoric acid solution. A comprehensive survey of substitute lining materials was not contemplated. It was stipulated at the beginning of the investigation that only materials on the market, available in large quantities, would be tested and that these should be reasonable substitutes from a wear-resistance viewpoint as determined from known physical characteristics. Marble and limestone, for example, could be eliminated immediately. Quartzite, granite and porcelain were selected as likely substitutes for Belgian silex and were subjected to quality tests. Materials Tested 1. Belgian Si1ex.—Sample blocks of a standard grade were taken from crates in which they had been imported. The stone was light gray in color and contained inclusions of small clusters of quartz crystals as well as light colored portions that might be calcite. This was a siliceous rock which appeared to be of igneous origin. 2. Quartzite.—Samples of quartzite were obtained from a quarry in Minnesota. The blocks exhibited a crystalline fracture. The stone was pink in color and composed of fine quartz crystals bound together with a siliceous cement. 3. Granite A was a fine-grained granite quarried in South Carolina. 4. Granite B was coarse-grained granite quarried in South Carolina. 5. Granite C was a coarse-grained granite quarried in North Carolina. 6. Porcelain A.—Sample blocks of the pebble-mill lining material were obtained direct from the manufacturer. It was white in color and of lower specific gravity than the natural materials. It did not have a crystalline structure. 7. Porcelain B.—Sample pebble-mill lining blocks of the porcelain were received direct from the manufacturer. It was white

Jan 1, 1947

By Charles H. Jacoby

In 1774 a Swedish chemist, C. W. Schule, first recognized manganese as an element. That same year Schule's associate, J. G. Gahn, isolated the element manganese for the first time. In 1856 the Bessemer process of steelmaking gave birth to the economic importance of manganese. Later, in 1882, Robert Hadfield discovered high manganese steels. Although the primary use of manganese is in the ferroalloy industry, two additional important uses for manganese are making chemicals and dry cell batteries. Manganese is also vital to plant and animal life. Various chemical compounds of manganese are used in fertilizers, feeds, glass manufacture, paints, varnishes, and for numerous medicinal and chemical purposes. For the study of industrial minerals and rocks, only the chemical and battery grade material is of concern, but for the sake of comparison, metallurgical aspects are included in this presentation. Although currently the world's largest consumer of manganese, the United States is producing only minor amounts of ore at the present time. This is due primarily to the fact that although huge deposits of manganese occur within our borders, all are of such low grade as to be economically unfeasible to mine. For many years various government agencies and segments of private industry have devoted sizable sums of money and time in an attempt to upgrade ores from the various deposits, and also in an attempt to recover manganese from blast furnace slags. In view of current world prices, and the quantity of high grade material available, there is little likelihood that any of these approaches will be found to be economically feasible in the near future. Geology and Mineralogy Mineralogy There are over one hundred minerals that contain manganese. These minerals vary from those with compositions that are predominantly manganese to those having only minor percentages. [ ] Geology From a geological standpoint most manga¬nese deposits are complex. In general, it can be said that all primary deposits of manganese are carbonates or silicates. The most productive and profitable have been those of sedimentary origin and residual concentrations. Examples of these residual types of deposits are associated with the metamorphosed lodes of Madhya, Pradesh, India, and the lateritic deposits of Orissa and Bihar, India; nodules in the residual clays of the Philippine Islands, U.S. southern Appalachians and Arkansas, Ghana, and Brazil. Sedimentary manganese deposits are best exemplified by the Nikopol district of Russia and the Tchiatouri area of Georgia, USSR. Hydrothermal replacements are characterized by the rhodochrosite deposits of Butte and Phillipsburg, Mont. In general, the hydrothermal type deposit has not resulted in any large tonnages being produced, but may have given

Jan 1, 1975

JESSE L. JONES,* Pittsburgh, Pa. (written discussion?).-The most important criterion on which judgment of the quality of manganese bronze can be based is its freedom from lead. Not over 0.03 per cent. of lead should be present in a good grade of manganese bronze. While it is not questioned that manganese bronze with a high tensile strength and considerable ductility can be made .from materials that will give a lead content of possibly 2 to 3 per cent., there is no doubt that such material, while it may machine readily, will be found to withstand the impact test very poorly, and hence be unsuited for high-grade engineering work. When lead is present in considerable amounts, it forms in small pools in the alloy and the material has little strength at these points; in fact, such spots in the metal are equivalent to nicks in a test bar as far as their effect on tensile strength is concerned. A further objection to a high lead content is the ease with which it oxidizes and its consequent tendency to produce dross. A second characteristic of a high-grade manganese bronze is a low content of manganese. This should not exceed 0.05 per cent.; in fact, very many of the best grades of manganese bronze show, on analysis, only a trace of manganese or no manganese whatever. Manganese is a deoxidizer and its ready oxidation protects the other metals of the alloy; but if it is present in large amounts it will produce considerable manganese dioxide, which does not separate readily from the molten alloy and may produce black specks or drossy spots and render the obtaining of clean castings difficult. Aluminum should be present in a good grade of manganese bronze in only very small amounts. A content of 0.10 per cent. aluminum is ample. Larger amounts have a tendency to increase the shrinkage of the alloy, to give the ingots and castings a white, scruffy appearance, and to prevent the beautiful, golden, oxidization color characteristic of high-grade manganese bronze and a most excellent indication of quality. The work that the author of the paper has done is valuable from a con- servation standpoint, and it will supplement, in a marked degree, the advances that have been made by a number of manufacturers of manganese bronze in utilizing the turnings from this material. A number of firms have succeeded in making a very good grade of ingot metal from turnings and other light scrap, obtaining a tensile strength and elongation

Jan 4, 1919

By E. F. Raffo

THE design of the Chuquicamata concentrator offered an unusual combination of problems, all of which had, in one way or another, a definite effect upon the final arrangement of all the equipment and necessary facilities. First of all, a remotely located project of this magnitude required careful selection of equipment with an adequate supply of replacement parts and in some cases necessitated stand-by spare equipment ready for immediate use. Fortunately, in the course of determining the proper flowsheet, in itself a prime factor in the concentrator design, it was possible to conduct numerous grinding and flotation tests at the Anaconda and Andes concentrators. As a result of these tests made under actual operating conditions, most of the major equipment best suited for treating the Chuquicamata ore efficiently was decided upon while preliminary design layouts were still being made. The design has been based primarily on the treatment of sulphide ore crushed to about 3/4 or 1 in. However, until the new sulphide crushing plant is completed it will be necessary to handle ore crushed to 3/8 in. in the existing oxide crushing plants and to some extent a mixed ore which has had its oxide copper content removed by leaching. This mixed ore, known as leached residue, will contain a certain amount of sulphuric acid from the leaching process which necessarily requires special protective measures. Several factors influenced the final location of the Concentrator. The only established fact known during preliminary design layout was the elevation of the dumping floor over the fine ore bin. This was predetermined by the desired level railroad grade across part of the existing tailing and leached residue dumps from the oxide plant to the bin. Next it was necessary that a site be chosen that would not require an excessively long haul from either the present oxide plant or the mine and in addition provide a fairly constant natural ground slope sufficiently wide to accommodate the length of the ultimate concentrator. The site as finally chosen to meet the foregoing restrictions provided a natural ground slope of 6 to 7 pct. This was excellent, especially in a region subject to earthquakes, as it assured that foundations of heavy equipment and footings for building and crane columns would rest on cut or undisturbed ground. However, this shallow slope, although having some definite advantages in the overall consideration of plant layout, resulted in the need for extensive studies in the general arrangement of equipment. Wasteful and excessive vertical drops had to be eliminated in the

Jan 1, 1952