Search Documents

By F. W. C. Boswell, R. L. Cunningham, H. M. Weld

Chemical analysis shows the partition of the magnesium addition between the metal and the graphite is independent of whether the graphite is in the form of nodules or flakes. The bright central spot observed in nodular graphite polished sections is shown to be due to the structure of the nodules. DURING the past few years numerous papers have been published on the production1-7 and heat treatment" of nodular cast irons. However, very little information is available on the structure of the nodules and the reason for their formation. It would appear that an explanation of the phenomenon of nodulation must await a detailed knowledge of the nature of the nodule. Disagreement exists among various workers on such a fundamental point as to whether or not a nodule actually contains a microscopically visible, nongraphitic nucleus.9-11 Work was initiated with a view to obtaining definite information on this and other aspects of the problem. Chemical Separation and Analysis Microscopic appearance had indicated9-11 that a nongraphitic core might exist in nodules (Fig. 1). It appeared that a chemical comparison of separated nodules and flake graphite would be profitable, for if the core is nongraphitic a relatively large amount of certain elements would be found in the nodules as compared to the flake. This comparison could best be made by obtaining nodules and flake from the same melt of cast iron, part of which had been in-noculated with a suitable addition reagent for the formation of nodules. A 300 lb melt was produced. About half of this was innoculated in the ladle with an Fe-Si-Mg alloy to produce nodules and cast into keel blocks; the remaining half of the melt had silicon added in an effort to compensate for the silicon in the innoculant used in the other half of the melt and this was cast into similar keel blocks. The analyses of the resultant irons are given in Table I. Nodules and flake were chemically extracted from 2 kg samples of metal as described in the appendix. While this method dissolved the iron and chromium carbides, it did not dissolve the titanium, vanadium, and molybdenum carbides. These latter carbides could have been removed by nitric acid, but in other experiments it was found that it attacked pools of metallic iron entrapped in the nodules which had, until the nitric acid treatment, been protected from the attack of the sulphuric, hydrochloric, and hydrofluoric acids. It will be shown in the next section that entrapped iron exists in nodules but not in flake. On microscopic examination many tiny irregular particles were observed to accompany both the nodules and the flake. These were identified by tabling a sample of nodules from which a sufficient fraction was obtained for X-ray analysis. A good pattern of titanium carbide was obtained indicating that this was the predominant compound present. Since it was not possible to determine how completely the carbides could be removed mechanically and since their removal from flake is much more difficult, it was decided not to resort to any separation as this would render further comparisons more difficult. The samples were ashed in a combustion

Jan 1, 1953

By K. Barron

The glass insert stressmeter, or photoelastic stressmeter, is an instrument designed to determine stress changes occurring in rocks. It has several potential advantages over other such devices in that it is a biaxial device, it is simple and it is cheap to make. The object of this study was to assess the behaviour of the meter under biaxial loads and to examine some of the problems associated with measurement and interpretation of the fringe pattern. This assessment has been carried out by comparing theoretical and laboratory behaviour of the meter. It has been shown that: a) There are certain optimum measuring points in the meter at which measurements should be made for best accuracy. The position of the points depends on the ratio, n, of the biaxial stresses. b) The meter&apos;s sensitivity can be assumed to be independent of the rock modulus E provided that the rock modulus is < 2.5 x 106 psi and not, as previous workers have assumed, if E < 5 x 106 psi. c) There are several methods of separating the principal stresses; some of these are unsatisfactory. A new method is proposed and discussed. d) The meter sensitivity decreases as the ratio of the biaxial stresses approaches unity; the accuracy thus also decreases. e) The axes of symmetry of the fringe pattern give an excellent indication of applied stress direction. f) Laboratory calibrations are in good agreement with theory. The glass insert or photoelastic stressmeter is an instrument designed to determine stress changes occurring in rocks. It has several potential advantages over other such devices in that it is a biaxial device, it is simple and it is cheap to make. This stressmeter has been described in detail.l,2 Basically it is a hollow glass cylinder that has at one end a light source and filters producing circularly polarized light. The glass cylinder and source are grouted into a borehole in rock and the face of the cylinder is viewed through a quarter wave plate and an analyser. If, after installation, a stress change occurs in the rock, then a distinct colored isochro-matic fringe pattern is seen in the meter. The fringe order at any point in the meter can be determined by counting the fringes and measuring the fractional fringe orders by the Tardy compensation method. The relation between the fringe order at any point and the applied stress change can be determined either by calculation or by calibration. The object of this study was to assess the behavior of this stressmeter under biaxial loading conditions and to examine some of the problems of interpretation of the fringe pattern. THEORY Hiramatsu et a14 have determined the stress distribution in a hollow cylindrical inclusion in an elastic host material when subject to uniaxial stress. Using this solution, the biaxial case of stress p in the x direction and stress q in the y direction (Fig. 1) can be solved by superposition. This has been done in Appendix 1. It is shown that the principal stress difference (s1 -s2) at any point (r,?) in the cylinder is given by:

Jan 1, 1965

By Ravindra M. Nadkarni, Milton E. Wadsworth

The kinetics of cetnentation of copper with iron were observed to follow first-order kinetics and increase with speed of agitation to a limiting value. Maximum rates agree closely with theoretical values based upon a model of aqueous solution diffusion through a litniting boundary film. Back reaction kinetics are shown both theoretically and experimentally to be independent of ferrous iron concentration in solution. The inlportance of attnospheres of air, oxygen, nitrogen, and hydrogen was studied and the results have been correlated with several impovtant oxidation processes involving metallic iron and copper. The kinetics of the reaction of ferric ion with metallic iron were found to be slow in the absence of metallic copper and essentially proportional to the surface area of metallic copper present in the system. THE precipitation of copper on iron is classic as an example of a relatively ancient art applied successfully for centuries with little fundamental understanding of the important parameters involved. There is some indication that the process has been a commercial means to produce copper since the sixteenth century.&apos; The amount of fundamental work on the cementation of copper with iron is not great. Wartman and Roberson2 carried out a series of detailed copper cementation experiments using natural and synthetic mine water. The following were presented as the three principal reactions: Reaction [I] is the desired cementation reaction and accordingly 0.88 lb of iron would produce 1 lb of copper. In actual practice iron consumption would more normally fall in the range of 1.5 to 2.5 lb per lb of copper. Wartman and Roberson attributed the excess consumption of iron to Reactions [2] and [3]. They found that Reactions [I] and [2] proceeded at approximately the same velocity while Reaction [3] was much slower and would be diminished by controlling the contact time. It was also pointed out that increased agitation is beneficial in removing hydrogen bubbles and barren layers of solution at the iron surface as well as removing contaminants resulting from the hydrolysis of iron. Episkoposyan3 and Episkoposyan and Kakovskii4 studied copper and silver cementation on rotating iron disks in chloride solutions. The kinetics based upon a diffusion model were first order and varied linearly with surface area and with angular velocity raised to the one-half power according to the Levich equation. The experimental activation energy for both copper and silver was approximately 3 kcal per per mole. Excess iron consumption was found to increase with temperature. The rate of cementation first increased with increasing acidity and then diminished at high acid concentrations. sutolov5 has presented an excellent review of the Leach-Precipitation-Flotation (LPF) process including a discussion of copper cementation from an electrochemical point of view although few experimental results were presented. From voltage considerations he predicted that cementation should not be influenced by the concentration of ferrous iron in solution. He considered several secondary reactions including Reactions [2] and [3] and pointed out the importance of oxidation of ferrous iron to ferric with oxygen. In addition it was suggested that Reaction [2] was enhanced by the dissolution of metallic copper by ferric iron which in turn consumed excess iron by the cementation reaction, Eq.[1]. Cementation of copper on metals other than iron has been studied by several investigators but, as in the case of iron, the amount of fundamental work is not extensive. Bashkova and kovalenko6 and Bashkova7 studied the cementation of copper on indium from copper and indium sulfate solutions. The rate was found to be first order and to increase with acidity. This was associated with a decrease in potential (EIn — ECu) and the simultaneous reduction of hydrogen ions at low pH. The rate of cementation also decreased with increasing indium concentrations which was postulated to be due to the decrease in the rate of diffusion of the ions in solution. Below 97°C the experimental activation energy was found to have the unusually low value of 2 kcal per mole and was attributed to diffusional control. Above 97°C the rate increased suddenly and was explained as a change in the rate-controlling step to a chemical reaction. In Part I of this study Nadkarni et a1 .1 have reported on preliminary results obtained in a laboratory study of the kinetics of the cementation process. The rate was found to be first order, proportional to the surface area of the iron, and to increase with speed of stirring until a maximum rate was observed. At low stirring speeds the deposit was spongy and adherent. At medium speeds the copper peeled off in bright strips and at high speeds finely divided copper was produced and continually removed from the surface. The amount of excess iron consumed increased with speed of stirring and with temperature. The average experimental activation energy combining results from several types of iron was 5.8 + 1.6 kcal per mole suggesting diffusional control through a limiting boundary film. Traditionally copper cementation has been carried out over the centuries in gravity-fed launders of various design containing scrap iron. More recently rotating drum precipitators and activated launders8&apos;10 have been used. In the latter, copper-bearing solutions are

Jan 1, 1968

By E. Buehler, R. H. Willens

A Hew melting technique has hem adapted to the rapid quenching of- alloys from the liquid state. The inelting method has no limitations on the alloys investigated for there is no reaction with crucible materials and the most refractory materials are easily melted. The vate of heating is so rapid that alloys which have a high vapor pressure constituent can be melted with a minimal loss in material. Several new superconductovs have been discoveved by vapid quenching of lolten alloys. THE rapid quenching of alloys from the liquid state has led to the discovery of many new metastable phases. The methods initially used were limited to alloys which did not react with crucible materials.1,2 There was also the unmentioned limitation in tem- perature. Alloys with melting points much greater than 2000°C could not be melted in the rapid-quench apparatus. Recently, there have been successful attempts to rapidly quench reactive alloys by Moss et at. and Matthias Moss et al. injected powdered material (325 mesh) into a high-temperature plasma and the high-velocity molten droplets impinged on a cooled copper plate. The technique innovated by Matthias was to melt the alloy in an arc furnace and splatter it against a copper plate by means of a high-velocity gas jet aimed at the melt. I) FAST COOLING APPARATUS The creation of a metastable phase in a given alloy system by rapid cooling from the melt is contingent on the quenching rate. Some alloys require very slow rates while other alloys require the ultimate in quenching rate. At the present time, the vertical-gun technique of Duwez and willens&apos; has demonstrated, in practice, the highest quenching rates and thus the best

Jan 1, 1967

By Arthur C. Green

A group of 13 cities situated in Los Angeles and Orange counties in Southern California is engaged in constructing an aqueduct to carry water from the Colorado River at a point near Parker, Arizona, to a distribution point near Riverside, California. The aqueduct will have a total length of approximately 241 miles, and is designed to deliver 1605 cu. ft. of water per second, or a little more than one billion gallons per day. The aqueduct crosses a barren, desert waste and the project includes approximately 91 miles of 16-ft. tunnel. The large amount of tunnel driving that has been done in this country in the past few years has resulted in some remarkable developments in equipment and methods. The building of the Colorado River Aqueduct,, with its 91 miles of tunnels, has called on the best engineering knowledge in the country. New and better equipment has been designed for all phases of the work, and this equipment has been coordinated and adapted to the various conditions with a high degree of efficiency. The result has been that records for tunnel driving have been set under adverse natural conditions that exceed the estimates for progress under good conditions. All of the tunnels in the main aqueduct, except the Valverde and Bernasconi at the western end, have a finished diameter, inside the concrete lining, of 16 ft. Fig. 4 shows a section of the tunnel with the concrete lining in place. Fig. 5 illustrates the finished tunnel in three typical sections. The standard tunnel grade is 3.432 ft. per mile in the 16-ft. tunnels, but the Valverde and Bernasconi tunnels have a steeper grade and a finished diameter of 15 ft. 3 in. The rough bore of the large main aqueduct tunnels averages 12.95 solid cubic yards of material per foot of advance in timbered sections and 10.76 solid cubic yards per foot in unsupported sections. Tunnel Driving While the Conway mucker has been used on tunnel work for years, a larger and more powerful Conway was designed to meet the require-

Jan 1, 1937

By W. H. Bassett

THE modern smelting and refining of copper is distinctly an American development. The present demand for sound and perfect castings for rolling is due to the development of American industry. Prac-tically every article made from sheet metal or, for that matter, from any form of metal is made by mass produc-tion methods. Faulty material disturbs the orderly sequence of operations and in addition requires expen-sive inspection and unbearable rejection of finished product. This demand, therefore, is positive and will have to be met. Some mines produce ore that can be smelted and re-fined without the electrolytic process into satisfactory copper for the wrought metal industry, and some of these ores carry small amounts of impurities that are of use in hardening and toughening the copper. Most of the copper ore mined contains impurities that must be removed and, fortunately, precious metals which are separated at the same time make this re-moval profitable. The modern electrolytic refineries have their methods so well under control that the product meets all re-quirements without question if properly fire refined and cast. The "if" in this case is important, because there is evidence of carelessness or want of control at times in the material from some of the producers. It is nec-essary that the melted cathodes should be saturated with oxide to dispose of sulfur and that the copper should then be poled to the proper pitch or set. Sometimes statements leak out to the effect that it is unnecessary to oxidize completely the molten cathodes and a little less rabbling saves poles, which are expensive. The re-sult is that the rolling mill gets porous castings and produces seamy or slivered sheets or strips. The condition of the molds, their temperature, and the temperature of the metal are all important to good copper cakes, wedges, or wire bars. Cracked, and burned molds leave rough places and porous spots. Molds which are out of shape, or cracked, make shrink-age cracks which gap open when the castings are hot-rolled. Dampness means porosity. Drops of oil mean porous or honey-combed areas. Poor or irregular dress-ing means mold wash in the castings. Cold copper or slow pouring means cold sets.

Jan 4, 1928

By Samuel Doak

THE utilization of rotary kilns, of the well-known cement type, for the preparation of iron ores, for the blast furnace, has become of considerable economic importance within the past 10 years in certain localities, notably those where the native ores are lean. Such kilns may be used simply for the agglomeration of ores too fine to be charged into the blast furnace (i.e., ores whose loss in the dust catchers is excessive, and whose fineness is detrimental to the working of the furnace), or for the desulphurization of lump and fine ores the sulphur content of which does not exceed 6 or 7 per cent. The desulphurizing action can be combined with that of agglomeration provided the kiln is sufficiently large. Other processes have been developed for the same purpose, but while I am not able to draw a comparison between them by reason of lack of sufficient data, it is safe to say that the kiln, if properly dimensioned for the character of ore to be treated, will compare favorably in its results, both as to economy and quality of product, with any other process. It is not, however, as well adapted for the treatment of flue dust, as is a sintering operation, on account of the large percentage of fine coke contained therein. Any combustible entering the kiln at its feed end renders the process very much more expensive and unsatisfactory on account of the difficulty of controlling the temperature, also because of the rapidity with which long "rings" form, due to the increased heat at the cooler end of the kiln. The greatest value of the kiln at present is in the treatment of pyrites cinder; that is, the residue from pyrites ore after the extraction of the greater part of the sulphur. This cinder, while high in iron content, has too much sulphur remaining in it to be allowed to form a large part of the blast-furnace burden, without further treatment. It will range in metallic iron from 42 per cent., representing a very low-grade cinder, from a domestic pyrites, to 64 per cent. of the residue from the best Spanish ore, and the corresponding silica content will vary from the maximum of about 25 per cent. to 1 ½ per cent. The residual sulphur depends largely on the type of burner used in the original desulphurization. In general, the leanest original ores retain the greatest amounts of sulphur. In

Jan 9, 1915

By O. Cuscoleca

The Austrian plants at Donawitz and Linz were the first to blow steel with high purity oxygen. The paper shows how the process was developed and gives a survey of the results achieved to date. Compared with open hearth steel of equal quality, the obvious advantages of oxygen steel are the low investment and conversion costs. The nitrogen content of oxygen steel is not higher than that of good open hearth steel. Rimmed and killed steel products made by the oxygen process are superior to rimmed and killed steel products made by the best open hearth process. TWO new steel plants using the principle of making steel with high purity oxygen went into operation in Austria, one at Linz (Vereinigte oster-reichische Stahlwerke) in November 1952 and the other at Donawitz (dsterreichisch-Alpine Montan-gesellschaft) in May 1953. An estimated 330,000 metric tons were produced by the two plants in 1953, the first year of operation. In 1954 production by Austrian plants- using the high purity oxygen approach will be raised to 450,000 metric tons. This will be in addition to facilities in Huckingen (Man-nesmann A. G., Düsseldorf, Germany), those planned and under construction at Hamilton, Ontario, Canada (Dominion Foundries and Steel, Ltd.), and elsewhere. It is expected that by 1955 a total capacity of one million tons of high purity oxygen steel will be available. At the close of the last century, because of increasing availability of scrap, open hearth steel production forged ahead at an ever increasing pace. This caused world steel production to rise faster than pig iron production and finally to overtake it. In 1911 65 million tons of steel were produced against 64 million tons of pig iron. World steel production was 209 million tons in 1951, while pig iron output was only 147 million tons. The 1951 breakdown for steel shows 118 million tons made from pig iron, while the balance, 91 million tons or 44 pct of the total tonnage of steel produced, was made from scrap. This increase in crude steel production on a basis of high scrap consumption led to the world market scrap shortage and soaring scrap prices. In the United States and other nations, production of converter steel has fallen far behind that of open hearth steel. The surplus of processing scrap, un-absorbable by converting mills and thus a welcome source for open hearth and electric melting shops in the past, together with regular scrap purchases, no longer can meet requirements of both open hearth and electric steel production in Europe. In addition, recent modification of the basic bessemer process, blowing with oxygenated blast, substantially raised the scrap capacity of these plants. Any further expansion of world steel production will necessitate utilization of self-containing processes in regard to scrap because of the shortage.

Jan 1, 1955

By J. F. K. Brown, E. E. Roecker

For three years The Hudson Coal Co. has used egg anthracite instead of coke in its foundry cupola. It has long passed the stage of being told it cannot be done—the metal would be cold, of poor quality, or the speed of operation would be low. From observation, from use and from test. we know that our metal is about average; the cast iron invokes no adverse comment from the machine shop and the speed suits our foundry requirements. We have there-iore resolved into practice anthracite combustion processes in an industrial furnace formerly using coke, under conditions suitable to our needs. When it comes to translating what we know into use in another cupola, however, where operating conditions may be different, or to explaining why, with seemingly the same conditions in our own cupola, we have attained sometimes a temperature of 2800° in the metal and at another time 2600°, or a speed of 5 tons per hour against 2 35 tons per hour, we cannot do it. We cannot do this because there seems to be an unbridged gap between laboratory ideas on combustion and practical ideas on com-bustiqn, which we have been unable to cross in terms understandable to us as practical consumers. This gap or bridge centers around the problem of how combustion actually takes place; and we believe it is controlled by two factors: (I) the character of the surface of the fuel and (2) the space provided and needed within which the oxygen of the air is allowed to or can act on that surface. It has long been contended on behalf of coke that porosity is an important factor in combustion, although, admittedly, there are two schools of opposing thought on this question, as revealed in technical literature. It has been understood generally that a light, porous coke is the best metallurgical fuel because there are more square inches of carbon exposed to the blast of air, therefore more useful carbon-dioxide reactions can take place in the given space between the entrance of the air and the point where useful work is done. It is now our general idea that the heavier and the harder the coal, the better the metallurgical fuel, provided the surface of that fuel is suitable for fast reaction with the oxygen. Time and Space A cupola is loaded in layers of fuel and iron. The horizontal line where the first charge of iron rests on the coal is the top of the bed coal. With us that is 22 in., usually, above the tuyeres where the air enters. This means 600 lb. of coal. Every subsequent coal layer is 100 to 125 lb. of coal, and that 100 to 125 lb. of coal melts 1000 lb. of iron at around 2700° in the ladle. This quantity of coal represents a 3-in. layer spread across the cupola. The question arises: If this 3 in. of coal will melt 1000 lb. of metal, why was it necessary to use 600 lb., or 22 in., of coal beneath and between the first charge of iron and the air entrance?

Jan 1, 1944

By E. E. Roecker, J. F. K. Brown

For three years The Hudson Coal Co. has used egg anthracite instead of coke in its foundry cupola. It has long passed the stage of being told it cannot be done—the metal would be cold, of poor quality, or the speed of operation would be low. From observation, from use and from test. we know that our metal is about average; the cast iron invokes no adverse comment from the machine shop and the speed suits our foundry requirements. We have there-iore resolved into practice anthracite combustion processes in an industrial furnace formerly using coke, under conditions suitable to our needs. When it comes to translating what we know into use in another cupola, however, where operating conditions may be different, or to explaining why, with seemingly the same conditions in our own cupola, we have attained sometimes a temperature of 2800° in the metal and at another time 2600°, or a speed of 5 tons per hour against 2 35 tons per hour, we cannot do it. We cannot do this because there seems to be an unbridged gap between laboratory ideas on combustion and practical ideas on com-bustiqn, which we have been unable to cross in terms understandable to us as practical consumers. This gap or bridge centers around the problem of how combustion actually takes place; and we believe it is controlled by two factors: (I) the character of the surface of the fuel and (2) the space provided and needed within which the oxygen of the air is allowed to or can act on that surface. It has long been contended on behalf of coke that porosity is an important factor in combustion, although, admittedly, there are two schools of opposing thought on this question, as revealed in technical literature. It has been understood generally that a light, porous coke is the best metallurgical fuel because there are more square inches of carbon exposed to the blast of air, therefore more useful carbon-dioxide reactions can take place in the given space between the entrance of the air and the point where useful work is done. It is now our general idea that the heavier and the harder the coal, the better the metallurgical fuel, provided the surface of that fuel is suitable for fast reaction with the oxygen. Time and Space A cupola is loaded in layers of fuel and iron. The horizontal line where the first charge of iron rests on the coal is the top of the bed coal. With us that is 22 in., usually, above the tuyeres where the air enters. This means 600 lb. of coal. Every subsequent coal layer is 100 to 125 lb. of coal, and that 100 to 125 lb. of coal melts 1000 lb. of iron at around 2700° in the ladle. This quantity of coal represents a 3-in. layer spread across the cupola. The question arises: If this 3 in. of coal will melt 1000 lb. of metal, why was it necessary to use 600 lb., or 22 in., of coal beneath and between the first charge of iron and the air entrance?

Jan 1, 1944

By Henry Rawdon

THE METHOD of demonstrating the structure existing in a metal or alloy at high temperatures, by etching a polished sample after it has been heated to the desired temperature, is quite familiar to metallographists. The usual procedure1,2 is to heat the specimen, previously polished for microscopic examination, to the desired temperature, in a neutral atmosphere (hydrogen or nitrogen), then admit the etching gas. (chlorine, hydrochloric acid or similar gas) for. a few seconds, and finally, after flushing out the etching gas with the neutral one, cool the specimen in the neutral atmosphere. The pattern produced by etching at a definite temperature is usually taken as a record of the microstructure prevailing at that temperature. It has frequently been pointed out that changes in composition of the surface metal occur during the preliminary heating in the neutral atmosphere, so that the appearance produced&apos; by the etching at high temperature may not exactly represent the condition of the interior of the specimen. To overcome this uncertainty, the heating has sometimes been done in vacuo,3 the etching gas being ad-mitted when the desired temperature was reached, then pumped out and the specimen cooled in vacuo.

Jan 2, 1920

By B. Blumenthal

THE present investigation was planned as a survey of the lead-rich portion of the ternary lead-antimony-silver system by thermal analysis. Since, however, a rigorous application of the conventional thermal analytical method is time consuming, an attempt was made to speed up the investigation by reducing the time required for a single thermal analysis. This was done by increasing the rate of cooling to 12° to 18°C. per minute, since such a rate does not permit even an approach to equilibrium conditions, the melt was stirred vigorously by a stirrer operating at the high rate of 665 r.p.m. This proved to be effective in obtaining cooling curves with distinct points of arrest and of excellent reproducibility, which satisfactorily compare with those obtained at a rate of 1" to 2°C. per min. with or without slow stirring (Fig. I). By this method the lead-rich end of the lead-alltimony system and a series of ternary alloys in sections parallel to the lead-antimony side of the ternary system were investigated and it was observed that the two branches of the liquidus curve of the binary alloys did not intersect at the euteotic temperature. An equivalent effect mas observed in the ternary system. The eutectic temperature of the binary lead-antimony system was found to be 252.0°C., which confirms the recent in- vestigation by Pellini and Rhines,1 who determined the eutectic temperature to be 2 51.5°C. The observation that the curves of primarY crystallization of the lead-antimony system do not intersect at the eutectic temperature was previously made by Dean.2 Dean explains the phenomeilon by assuming the existence of a compound Sb4pb. He felt that supercooling was not the cause of the phenomena because he was unable to influence them by inoculation. The X-ray investigation by Solomon and Morris-Jones,3 the metallographic investigations by Stead,4 Charpy,5 Gontermann,6 and Dean, Zickrick and Nix,7 and the numerous investigations of physical properties, definitely disprove the occurrence of any compound. The work of Dean was not confirmed by Broniewski and Sliwoski,8 whose experiments did not show any irregularity and who report a eutectic composition of 13 per cent antimony and a eutectic temperature Of 2500 to 252°C. at a rate Of coo1ing of about 6°C. Per min. Abell Redlich and Adler9 then report a eutectic composition of 12.1 per cent upon reviewing the previous publications and adding a few of their own cooling curves. In 1934 Quadrat and Jiriste10 found from careful analyses of the bottom portion of slowly cooled hypereutectic melts that the eutectic only 11 .4 to 11.5 per cent antimany. (Previous analyses by Stead4 .in 1891 gave 13 per cent.) Weaver,ll however, reported in 1935 that cooling cunres indi-

Jan 1, 1944

By B. Blumenthal

THE present investigation was planned as a survey of the lead-rich portion of the ternary lead-antimony-silver system by thermal analysis. Since, however, a rigorous application of the conventional thermal analytical method is time consuming, an attempt was made to speed up the investigation by reducing the time required for a single thermal analysis. This was done by increasing the rate of cooling to 12° to 18°C. per minute, since such a rate does not permit even an approach to equilibrium conditions, the melt was stirred vigorously by a stirrer operating at the high rate of 665 r.p.m. This proved to be effective in obtaining cooling curves with distinct points of arrest and of excellent reproducibility, which satisfactorily compare with those obtained at a rate of 1" to 2°C. per min. with or without slow stirring (Fig. I). By this method the lead-rich end of the lead-alltimony system and a series of ternary alloys in sections parallel to the lead-antimony side of the ternary system were investigated and it was observed that the two branches of the liquidus curve of the binary alloys did not intersect at the euteotic temperature. An equivalent effect mas observed in the ternary system. The eutectic temperature of the binary lead-antimony system was found to be 252.0°C., which confirms the recent in- vestigation by Pellini and Rhines,1 who determined the eutectic temperature to be 2 51.5°C. The observation that the curves of primarY crystallization of the lead-antimony system do not intersect at the eutectic temperature was previously made by Dean.2 Dean explains the phenomeilon by assuming the existence of a compound Sb4pb. He felt that supercooling was not the cause of the phenomena because he was unable to influence them by inoculation. The X-ray investigation by Solomon and Morris-Jones,3 the metallographic investigations by Stead,4 Charpy,5 Gontermann,6 and Dean, Zickrick and Nix,7 and the numerous investigations of physical properties, definitely disprove the occurrence of any compound. The work of Dean was not confirmed by Broniewski and Sliwoski,8 whose experiments did not show any irregularity and who report a eutectic composition of 13 per cent antimony and a eutectic temperature Of 2500 to 252°C. at a rate Of coo1ing of about 6°C. Per min. Abell Redlich and Adler9 then report a eutectic composition of 12.1 per cent upon reviewing the previous publications and adding a few of their own cooling curves. In 1934 Quadrat and Jiriste10 found from careful analyses of the bottom portion of slowly cooled hypereutectic melts that the eutectic only 11 .4 to 11.5 per cent antimany. (Previous analyses by Stead4 .in 1891 gave 13 per cent.) Weaver,ll however, reported in 1935 that cooling cunres indi-

Jan 1, 1944

By G. D. Van Arsdale

This paper describes a series of experiments leading to the development of a method for leaching the mixed ores of the Inspiration Consolidated Copper Co., containing chalcocite and silicates of copper, by the use of solutions acidified with sulfuric acid and carrying ferric sulfate. Iron is added to the solutions and ferric iron is regenerated electrolytically to a percentage high enough to act as an effcient solvent. The decreased yield is partly compensated for by a higher current density. An important problem in modern copper metallurgy, particularly in the Southwest, has been to obtain good recoveries from what are commonly known as mixed ores; that is ores in which the copper occurs partly as oxide and partly as sulfide compounds. The dividing line between mixed ores and ores commonly accepted as concentrating is not definite. In other words, much ore now being concentrated carries considerable copper in non-sulfide form, on which recoveries are not so good as on ores carrying less of these constituents. While treatment by concentration may be commercially profitable on ores carrying oxide copper within certain limits, there are large deposits for which the application of concentration could not be considered, and yet which have not been considered amenable to leaching because they carried too much sulfide. The Inspiration Consolidated Copper Co. has large amounts of such mixed ores, and this paper is an account of the experimental work by which a method was developed for their treatment, and for which a large plant is now being erected by the Inspiration Co. It is not claimed that the method is a general solution of the problem of mixed-ore treatment but it is apparently well adapted for leaching the ores of the Inspiration Co., for which it was designed. The work done has covered preliminary laboratory and test-plant investigation, and a pilot-plant run, extending from March to the middle of December, 1923. Thoroughly consistent and satisfactory results were obtained continuously for more than six months in the pilot plant; and it is believed that the results and probable costs that can be had on a large scale have been definitely proved. The method, however, was designed for local conditions; and while the basic principles are general, there are ores on which it will not work and other ores for which considerable modification may be required.

Jan 1, 1926

By J. L. Foster, G. R. Gray, T. S. Chapman

The wall-building properties of salt-water drilling muds can be improved markedly by the addition of: (I) natural gums, such as traga-canth, karaya, and ghatti; (2) seaweeds, such as Irish moss; or (3) gelatinized starch. Results of laboratory tests have been confirmed by field trials. For drilling operations in which the mud becomes contaminated by salt, either through penetrating salt-bearing rocks or by addition of sea water to the mud, the added cost resulting from the use of one of the substances listed above is more than offset by freedom from stuck drill pipe and ease in running casing. Introduction It has been recognized for many years that oil production might be seriously hampered by infiltration of water from the drilling mud.l-4 As knowledge of the mechanism of the wall-building process advanced, methods were developed for evaluating the filtration characteristics of muds.5-ll The wall-building properties of freshwater muds are commonly regulated by the addition of bentonitic clays, or of agents to promote the dispersion of the natural mud solids. When strata bearing soluble salts are encountered in the course of drilling, the salts are incorporated in the mud; the clay solids are flocculated and water loss is increased tremendously. Methods gen-crally used in controlling filtration of freshwater muds are no longer applicable. The problem of reducing water loss from salt-water muds is not confined to any particular area, but is acute in parts of West Texas. Salt beds several hundred feet thick must be penetrated before the oil-bearing formation is reached. Since the formation drilled does not provide mud-making material, it is necessary to use large quantities of commercial clays, and even the best commercial clay does not afford relief from the problem of high filtration. A laboratory study has been made of methods of improving the filtration characteristics of salt-water muds, and some of the methods have been used in field practice. Laboratory Investigations Procedure Inasmuch as the immediate object of the investigation was the development of means of improving the wall-building properties of muds used in West Texas, an attempt was made to employ muds in the laboratory study comparable to those in field use. Samples of muds used in drilling the producing formations in six wells were secured. The properties of these samples are summarized in Table I, which lists the densities, viscosities, filtrations, and analyses of the filtrates for calcium, chloride, and sulphate. Viscosity was measured in the Stormer viscosimeter at 600 r.p.m. Water loss was determined at 80°F. with the Baroid low-pressure wall-building tester8 at a pressure of 100 lb. per sq. in. Filtration rates are considerably higher than those of usual fresh-water muds, which amount to about 20 C.C. in 30 min. Water loss was so rapid in samples 4, 5 and 6 that filtration was complete in less than 10 min. and the values for 30 min. were extrapolated from the rates at shorter

Jan 1, 1942

By G. R. Gray, T. S. Chapman, J. L. Foster

The wall-building properties of salt-water drilling muds can be improved markedly by the addition of: (I) natural gums, such as traga-canth, karaya, and ghatti; (2) seaweeds, such as Irish moss; or (3) gelatinized starch. Results of laboratory tests have been confirmed by field trials. For drilling operations in which the mud becomes contaminated by salt, either through penetrating salt-bearing rocks or by addition of sea water to the mud, the added cost resulting from the use of one of the substances listed above is more than offset by freedom from stuck drill pipe and ease in running casing. Introduction It has been recognized for many years that oil production might be seriously hampered by infiltration of water from the drilling mud.l-4 As knowledge of the mechanism of the wall-building process advanced, methods were developed for evaluating the filtration characteristics of muds.5-ll The wall-building properties of freshwater muds are commonly regulated by the addition of bentonitic clays, or of agents to promote the dispersion of the natural mud solids. When strata bearing soluble salts are encountered in the course of drilling, the salts are incorporated in the mud; the clay solids are flocculated and water loss is increased tremendously. Methods gen-crally used in controlling filtration of freshwater muds are no longer applicable. The problem of reducing water loss from salt-water muds is not confined to any particular area, but is acute in parts of West Texas. Salt beds several hundred feet thick must be penetrated before the oil-bearing formation is reached. Since the formation drilled does not provide mud-making material, it is necessary to use large quantities of commercial clays, and even the best commercial clay does not afford relief from the problem of high filtration. A laboratory study has been made of methods of improving the filtration characteristics of salt-water muds, and some of the methods have been used in field practice. Laboratory Investigations Procedure Inasmuch as the immediate object of the investigation was the development of means of improving the wall-building properties of muds used in West Texas, an attempt was made to employ muds in the laboratory study comparable to those in field use. Samples of muds used in drilling the producing formations in six wells were secured. The properties of these samples are summarized in Table I, which lists the densities, viscosities, filtrations, and analyses of the filtrates for calcium, chloride, and sulphate. Viscosity was measured in the Stormer viscosimeter at 600 r.p.m. Water loss was determined at 80°F. with the Baroid low-pressure wall-building tester8 at a pressure of 100 lb. per sq. in. Filtration rates are considerably higher than those of usual fresh-water muds, which amount to about 20 C.C. in 30 min. Water loss was so rapid in samples 4, 5 and 6 that filtration was complete in less than 10 min. and the values for 30 min. were extrapolated from the rates at shorter

Jan 1, 1942

By Homer W. Riley

ANTHRACITE SMALL power-driven, toothed, cast-iron rolls were used first to break anthracite in 1844. Prior to that time, men with hammers, who stood on perforated cast-iron plates, broke the large lumps into commercial sizes. In order to convert run-of-mine into the various sizes required by the anthracite industry, about 20 million tons must be broken, annually, into smaller sizes. This phase of anthracite preparation is of major importance, because the degradation accompanying reduction in coal sizes should be kept at a minimum. The exclusive use of toothed rolls for that purpose indicates that comminution by rolls is the best solution of the problem. Many improvements have been made in tooth design, but the most important was a reduction of the peripheral speed of the rolls from 1000 to 300 ft. per minute. The higher speed was based upon and approximated the velocity of a falling piece of coal when it entered the rolls, Exhaustive roll tests at the slower speed showed that the same size reduction could be affected with less degradation. The adoption, therefore, of slow-speed, compound geared rolls, especially for breaking the larger sizes, became quite general after 1912. A high-speed roll is shown in Fig. 1 and a slow-speed roll in Fig. 2. Anthracite Crushing Problems.-Crushing anthracite presents the problem of selecting a series of rolls that will produce the greatest percentage of the prepared sizes of nut and over. The size distributions to be expected are shown in Table 1. Coal breaking and crushing practices in anthracite breakers involve the use of equipment for comminuting the following classes of material: 1. Run-of-mine-plus 6 ½ -in. coal. 2. Sized coal-steamboat, broken, egg, stove, nut, and pea. 3. Flat coal--coal that is flat and hence not suitable for the market. 4. Bone--a piece of laminated coal and slate, crushed for the purpose of reclaiming the coal. 5. Breaker refuse, reduced to a size suitable for flushing into a mine for back-filling purposes.

Jan 1, 1950

By Herbert H. Kellogg

Graphs representing the standard free-energy of formation as a function of temperature for 21 fluorides are presented, along with estimated values for the standard free-energy of formation of 20 atedadditional fluorides. A few of the many possible uses of these data in metallurgical calculations are discussed, including the fluorination of oxides, sulphides, metallurgicaland chlorides, and the reduction of metal fluorides. RECENT papers which have presented free-energy data for oxides, sulphides, chlorides, carbonates, sulphates, and silicates in the form of free energy vs. temperature plots,1-5 have found important uses in teaching and metallurgical development work. This method of presentation of thermo-dynamic data serves to make available in readily usable form thermodynamic constants which are scattered throughout the literature, and to show by graphical means the stability relations which exist between the compounds of a given type. It is certainly desirable to have these free-energy-temperature diagrams for as many types of compounds as are of present or potential use in metallurgical processes. Thus, even though there are but few uses of metallic fluorides in extractive metallurgy today, the potential uses of fluorine processes are of great importance and serve as the principal justification of this paper. Recent developments in the production of fluoro-carbons have resulted in vastly improved methods for the production and handling of fluorine and corrosive fluorides, with consequent reduction in costs.".&apos; The extractive metallurgist should no longer overlook possible fluorine processes when development of a new process for a relatively high unit-price metal is being considered. In a previous paperv he author outlined in some detail the importance and use of free-energy data in metallurgical calculations and also discussed the properties of a standard free-energy vs. temperature diagram. The same method of presentation is adopted in this paper, and the reader is referred to the earlier work for explanations of the use of free-energy data. Thermodynamic Data This paper presents standard free-energy vs. temperature diagrams, Figs. 1 and 2, for those fluorides for which the major thermodynamic constants are known. In the calculations of the standard free-energy of formation (AGO), values of the enthalpy of formation at 298°K (?Ho,) were taken from "Selected Values of Thermodynamic Constants"8 most of the values of standard entropy at 298°K (S°298) were taken from "Selected Values"," but in a few cases the values given by Kelley9 ere preferred; data for the Phase changes came from "selected Values" and several of Kellley&apos;s publics- tions;0-12 and most of the specific-heat data were taken from Kelley.l0 The appendix gives a detailed list of the sources of the data. As explained in an earlier paper,6 he accuracy of some of the standard free-energy relationships is not high. An error of +1 kcal at 1000°C is expected in most of the curves of Figs. 1 and 2. The error may be as high as +3 kcal in some of the curves. Rather than attempt to estimate the reliability of each curve, the source of the data used is reported in the appendix, and the reader may compare these data with newer values as they become available. Figs. 1 and 2 fail to show values for the fluorides of many important metals. In most cases this is because the entropy of the metallic fluoride is unknown. For preliminary calculations it is often useful to have available the best estimate of an unknown datum, rather than no information at all. With this in mind, Table I lists estimated standard free-energy values for a number of important metallic fluorides not included in Figs. 1 and 2. The values reported in Table I were, calculated by Brewer et al.13 and are based on estimated entropy values. The estimated uncertainty of the values for each fluoride were calculated from the uncertainty values given by Brewer1&apos; for ?H°, and the entropy function.

Jan 1, 1952

By J. W. Hickman, E. A. Gulbransen

One of the important factors that determine the resistance of a metal or alloy to further chemical reaction is the structure of the superficial oxide film. A thorough understanding of the physical and chemical structure as well as the stability of the oxide film formed on the surface as a function of time and temperature of the chemical reaction might furnish clues as to the nature of the reaction process and the protective nature of the film. A comprehensive program has been undertaken to study these phenomena. This paper summarizes the structure of the oxide films formed on the metals iron, cobalt, nickel, chromium and copper at temperatures up to 700°C. Before the introduction of the electron diffraction technique, it was necessary to use either direct chemical analyses or X-rav diffraction analyses to determine the nature of the oxide film formed on the metal or alloy. Chemical analyses yields information on the percentages of the several atomic species present in the film while X-ray diffraction analyses yield information on the atomic geometry. In special cases the information obtained may be identical, but in general both viewpoints are necessary. Much of the early work was carried out on the oxidation of bulk samples where thick films were obtained. The products were identified after cooling to room temperature by X-ray diffraction and chemical analyses. Although much useful information has been obtained in this manner. little could be learned about the character of the protective oxides during the period when the films were actually protective. Evidence concerning the chemical structure of thin oxide films has been made possible by the development of the electron diffraction reflection technique. In this method the most fruitful investigations have been made by carrying out the reaction in situ at the temperature at which the film is actually protective. Literature The oxidation of iron has been extensively investigated by X-ray and electron diffraction. Jackson and Quarrelll found that oxide films formed and examined at the same temperature differed considerably from those allowed to cool to room temperature. The results showed that below 400°C the oxide that was stable in intimate contact with iron was Fe³O4; between 515° and 900°C. the stable film was FeO. Above the upper change point of iron the oxide was found to be Fe³O4. From 400&apos; to 515°C., FeO, Fe³O4 or a mixture of the two oxides was found. Recrystallization of the air-formed film below 400&apos; and above 900°C. led to the formation of Fe3O4. In the range where thicker films consisted of FeO, the air-formed film was converted to a new hexagonal oxide not previously described.

Jan 1, 1947

By E. A. Gulbransen, J. W. Hickman

One of the important factors that determine the resistance of a metal or alloy to further chemical reaction is the structure of the superficial oxide film. A thorough understanding of the physical and chemical structure as well as the stability of the oxide film formed on the surface as a function of time and temperature of the chemical reaction might furnish clues as to the nature of the reaction process and the protective nature of the film. A comprehensive program has been undertaken to study these phenomena. This paper summarizes the structure of the oxide films formed on the metals iron, cobalt, nickel, chromium and copper at temperatures up to 700°C. Before the introduction of the electron diffraction technique, it was necessary to use either direct chemical analyses or X-rav diffraction analyses to determine the nature of the oxide film formed on the metal or alloy. Chemical analyses yields information on the percentages of the several atomic species present in the film while X-ray diffraction analyses yield information on the atomic geometry. In special cases the information obtained may be identical, but in general both viewpoints are necessary. Much of the early work was carried out on the oxidation of bulk samples where thick films were obtained. The products were identified after cooling to room temperature by X-ray diffraction and chemical analyses. Although much useful information has been obtained in this manner. little could be learned about the character of the protective oxides during the period when the films were actually protective. Evidence concerning the chemical structure of thin oxide films has been made possible by the development of the electron diffraction reflection technique. In this method the most fruitful investigations have been made by carrying out the reaction in situ at the temperature at which the film is actually protective. Literature The oxidation of iron has been extensively investigated by X-ray and electron diffraction. Jackson and Quarrelll found that oxide films formed and examined at the same temperature differed considerably from those allowed to cool to room temperature. The results showed that below 400°C the oxide that was stable in intimate contact with iron was Fe³O4; between 515° and 900°C. the stable film was FeO. Above the upper change point of iron the oxide was found to be Fe³O4. From 400&apos; to 515°C., FeO, Fe³O4 or a mixture of the two oxides was found. Recrystallization of the air-formed film below 400&apos; and above 900°C. led to the formation of Fe3O4. In the range where thicker films consisted of FeO, the air-formed film was converted to a new hexagonal oxide not previously described.

Jan 1, 1947