Search Documents

By Herbert H. Kellogg

In 1930, Taggart, Taylor and Knoll1 found that addition of various electrolytes to suspensions of ground minerals resulted in the stopping or starting of Brownian movement of the suspended particles. On the basis of the many new facts found, they rejected the " classical"† theory of Brownian movement and proposed an "ioniza-tion " theory. This new theory was further supported in later publications by Taggart.3,4 The acceptance of the ionization theory by men in the field of flotation may be judged by the mention given this theory in Gaudin's "Principles of Mineral Dressing,'16 Wark's "Principles of Flotation,"8 as well as in a recent paper by Fitt, Thomas and Taggart.7 The proponents of the ionization theory have gone further than the mere statement of the new theory. A parallelism between the Brownian movement of mineral particles and their behavior in flotation was reported.1,3,4 Likewise, the correlation between flocculation-dispersion of mineral particles and the Brownian movement of these particles has been investigated.' Bankoffl5 has suggested that "slime-coating" can also be directly correlated with the Brownian movement of the slime particles. In each of the instances mentioned it is the ionization theory of Brownian movement that has been used to "explain" the correlations that were found. The essential conflict between the kinetic theory and the ionization theory can be understood best by a brief description of each. The kinetic theory* proposes that Brownian movement is caused by the impacts of liquid molecules against the solid particles. At any instant of time, the molecular impacts on all sides of the solid particle will not balance, and the particle will receive a push in some direction. According to this theory, dl particles suspended in a liquid are in Brownian movement. However, if the particle is very large, the impacts on all sides will very nearly balance and the motion will not be noticeable. Another factor, besides the size of the particle, that affects the magnitude of the Brownian movement is the viscosity of the liquid—the greater the viscosity, the less the displacement of particles by Brownian movement. This theory has been verified experimentally by measurement of the velocity of Brownian movement, and by measurement of the compacting of suspensoid particles under the influence of gravity.2 The originators of the ionization theory found that he addition of various electrolytes to slime pulps caused cessation or commencement of Brownian movement, depending upon the chemical nature of the particle and the electrolyte. The Brownian movement of quartz particles was observed to stop upon the addition of Certain electrolytes, where the conditions of the experiment prevented flocculation

Jan 1, 1947

By Frederick Laist

THE object of the construction and operation of the 80-ton leaching plant was to test out the leaching of sand tailings on a large scale and, if possible, determine a definite method of operation, and the best construction for the larger unit which is now being built. It was also of importance to obtain some practical data as regards cost items. The 80-ton plant was not expected to be a commercial success. A leaching process on such low-grade material necessitates the treatment of a very large tonnage.. Such a cost item as labor, for instance, is entirely out of proportion in such a small plant. The amounts of acid, salt, scrap iron, and fuel for roasting, however, are the same per ton in an 80-ton plant as in a 2,000-ton plant. These costs were definitely established. Also the percentages of extraction and grade of tailings were definitely determined for a large-sized unit. Following will be found the description of the plant, the method of operation and the results obtained. A -general view of the plant is given in Fig. 1. The bins consisted of one coal bin with a capacity of 30 tons, one salt bin with a capacity of 20 tons, and a "mill tailings" or feed bin which held 70 tons. The coal and salt bins were placed with their floor level even with the firing floor of the roasting furnace. The feed bin, to give it greater capacity, discharged about 12 ft. below this point, to a 12-in. conveyor belt, which, in turn discharged into a pug mill. This fed another conveyor belt, which discharged into the top hearth of the furnace. The furnace was an ordinary six-hearth MacDougall roaster, .20-ft. in diameter. It was equipped with two fire boxes, on opposite sides, the flames entering on the third hearth. An induced draft was obtained with a Buffalo blower, worked as an exhaust fan. Just above the top hearth was an annular flue around the whole circumference of the furnace. Slots at intervals of about 18 in. led from this flue down into the top hearth. The slots were 2 in. wide by 6 in. long. This annular flue proved rather unsatisfactory, as it tended to fill up with flue dust and choke the slots, thus cutting down the draft. The volume of gas through

Jan 8, 1914

By Frederick Laist, Howard Aldrich

The object of the construction and operation of the 80-ton leaching plant was to test out the leaching of sand tailings on a large scale and, if possible, determine a definite method of operation, and the best construction for the larger unit which is now being built. It was also of importance to obtain some practical data as regards cost items. The 80-ton plant was not expected to be a commercial success. A leaching process on such low-grade material necessitates the treatment of a very large tonnage. Such a cost item as labor, for instance, is entirely out of proportion in such a small plant. The amounts of acid, salt, scrap iron, and fuel for roasting, however, are the same per ton in an 80-ton plant as in a 2,000-ton plant. These costs were definitely established. Also the percentages of extraction and grade of tailings were definitely determined for a large-sized unit. Following will be found the description of the plant, the method of operation and the- results obtained. A general view of the plant is given in Fig. 1. The bins consisted of one coal bin with a capacity of 30 tons, one salt bin with a capacity of 20 tons, and a "mill tailings" or feed bin which held 70 tons. The coal and salt bins were placed with their floor level even with the firing floor of the roasting furnace. The feed bin, to give it greater capacity, discharged about 12 ft. below this point, to a 12-in. conveyor belt, which in turn discharged into a pug mill. This fed another conveyor belt, which discharged into the top hearth of the furnace. The furnace was an ordinary six-hearth MacDougall roaster, 20 ft. in diameter. It was equipped with two fire boxes, on opposite sides, the flames entering on the third hearth. An induced draft was obtained with a Buffalo blower, worked as an exhaust fan. Just above the top hearth was an annular flue around the whole circumference of the furnace. Slots at intervals of about 18 in. led from this flue down into the top hearth. The slots were 2 in. wide by 6 in. long. This annular flue proved rather unsatisfactory, as it tended to fill up with flue dust and choke the dots, thus cutting down the draft. The volume of gas through

Jan 1, 1915

By James S. Browning

The Mineral Resources Institute and State Mine Experiment Station of the University of Alabama conducted Humphreys spiral tests on fine coal waste from nine preparation plants of Alabama strip mining operations to determine the feasibility of recovering low ash and sulfur fuel meeting steam coal specifications. The ash in the samples ranged from 9 - 5l%, and the total sulfur ranged from 0.4J- 2.39%. Continuous laboratory tests using a Humphreys spiral gave good recovery of the coal with excellent rejection of the ash and pyritic sulfur. Coal recoveries of 83.6 - 94.1% were achieved from the different samples. Ash content of the clean coal products fell within a range of 5 - 12.2%, with a total sulfur content of 0.62 and 1.10%. In quality, the products were comparable or superior to those now being shipped from the preparation plants.

Jan 1, 1980

The ventilation of metal mines is becoming more of a fundamental requirement than it was 10 or even 5 years ago. There are many reasons for this, and in general they are based on economy or efficiency rather than health or safety, yet the latter enters into the picture in at least some instances. One Montana metal mine which had installed mine fans and a general ventilating system shut down the fan when there was a period of cessation of work; within a few weeks it was found that the underground timbers were becoming so covered with fungus that the fans were put into operation and thereafter continued in operation whether the mine was worked or not. The fungus soon disappeared and the cost of operating the fans was held to be far less than would be the numerous losses from timber decay which quickly started when cessation of air flow was encountered. A large iron ore mine in Michigan had much difficulty in holding men in a slicing region due to foul air under certain surface conditions as to direction of wind. Upon the placing of a moderate sized fan on the surface with some doors, stoppings and regulators underground, not only was the bad air condition removed but there was found to be a decided increase of tonnage per man per shift and timber decay was retarded to a very considerable extent. This particular mining company was rather inclined to be angry when I called attention to some of the what I considered very bad working conditions underground, and the mine superintendent for about a year and a half was on anything but friendly terms with me. Later on when the effect of the placing of the fan was found (the fan had been placed over his protest), that, man came through very nicely with a letter and congratulated me on the recommendation made and congratulated himself and the company on the conditions obtained after the installation of the fan. Poisonous Fumes after Blasting A copper mine in the Southwest with an ore of a high sulfide content has much difficulty due to poisonous fumes after blasting, and the, fan installation is as elaborate as those of many of the most nearly up-to-date coal mines, and coal mine splitting and regulating practices are being

Jan 1, 1927

By C. E. Lesher

THE Disco* process for the production of low temperature coke and its immediate predecessor, the Wisner or Carbocite process have been described in the voluminous literature of low temperature carbonization.1 This paper will describe the development of the process from the first attempt at commercial operation by the American Gas and Electric Co. at Philo, Ohio, Yn the 1920's to the successful operation in 1949 by the Disco Co., a division of the Pittsburgh Consolidation Coal Co., of the 1000-ton per day Disco plant near Pittsburgh, see Figs. 1-2. In the 1924 coal industry depression following the hectic post World War I expansion, the northern Appalachian, unionized bituminous coal fields were affected first and foremost, and Western Pennsylvania as hard as any. Competitive market pressure was heaviest on the lower grades of steam coals, notably the from the Panhandle district where ash and sulphur are inherently higher than in the same Pittsburgh coal bed to the east along the rivers. The firm structure of Panhandle coal while favoring the prepared sizes, depressed the usefulness and value of the finer sizes. Panhandle slack and nut slack were marketed with difficulty at consistent, and at times considerable, loss. Many solutions were suggested, and the Pittsburgh Coal Co. investigated all. Lower delivered prices through lower mine costs and more advantageous freight rates were obvious goals, but equally obvious were the difficulties of self attainment of either in any substantial measure. Selling Btu's in pipes was abandoned as an idea after a thorough study of the economics of distribution of what was then, and is even now, the only developed continuous process of complete gasification of bituminous coal-producer gas. Although the coal company purchased huge blocks of electric power, it sold not a car of coal to the central power stations. Public utilities controlled the markets for electric current, and it was found that no matter at how low a cost current might be put on the bus bars by the coal company, distribution to its widely scattered coal mines made such an enterprise practically impossible. Consolidation of underground operations and a huge modernization program of mining operations in the 1920's were but preparation for the introduction of mechanical cleaning of the coal for market, particularly the smaller sizes of steam, gas, and by-

Jan 1, 1953

By C. E. Lesher

THE Disco* process for the production of low temperature coke and its immediate predecessor, the Wisner or Carbocite process have been described in the voluminous literature of low temperature carbonization.1 This paper will describe the development of the process from the first attempt at commercial operation by the American Gas and Electric Co. at Philo, Ohio, Yn the 1920's to the successful operation in 1949 by the Disco Co., a division of the Pittsburgh Consolidation Coal Co., of the 1000-ton per day Disco plant near Pittsburgh, see Figs. 1-2. In the 1924 coal industry depression following the hectic post World War I expansion, the northern Appalachian, unionized bituminous coal fields were affected first and foremost, and Western Pennsylvania as hard as any. Competitive market pressure was heaviest on the lower grades of steam coals, notably the from the Panhandle district where ash and sulphur are inherently higher than in the same Pittsburgh coal bed to the east along the rivers. The firm structure of Panhandle coal while favoring the prepared sizes, depressed the usefulness and value of the finer sizes. Panhandle slack and nut slack were marketed with difficulty at consistent, and at times considerable, loss. Many solutions were suggested, and the Pittsburgh Coal Co. investigated all. Lower delivered prices through lower mine costs and more advantageous freight rates were obvious goals, but equally obvious were the difficulties of self attainment of either in any substantial measure. Selling Btu's in pipes was abandoned as an idea after a thorough study of the economics of distribution of what was then, and is even now, the only developed continuous process of complete gasification of bituminous coal-producer gas. Although the coal company purchased huge blocks of electric power, it sold not a car of coal to the central power stations. Public utilities controlled the markets for electric current, and it was found that no matter at how low a cost current might be put on the bus bars by the coal company, distribution to its widely scattered coal mines made such an enterprise practically impossible. Consolidation of underground operations and a huge modernization program of mining operations in the 1920's were but preparation for the introduction of mechanical cleaning of the coal for market, particularly the smaller sizes of steam, gas, and by-

Jan 1, 1953

By Robert B. Hoy

If the reader finds that the basic information in a commodity chapter is insufficient, he can consult the appropriate sources in this chapter to find more detailed or more up-to-date information. In these days, technology develops so rapidly that this 5th edition will be somewhat out of date even by the time it is distributed. A comparison of this edition with the 4th edition (1975) of Industrial Minerals and Rocks will clearly demonstate how rapidly the scene changes. One of the best sources of new information, of course, is attendance at technical meetings. For example, the papers presented at the national and sectional meetings of AIME usually discuss new developments in the respective divisions of the society. Frequently this information is available in Preprints. In addition some are printed in Mining Engineering and/or the Transactions of the Society of Mining Engineers of AIME. Furthermore, other professional and trade journals contain articles pertinent to the field. A journal introduced in 1967, Industrial Minerals, published by the Metal Bulletin, Ltd., London, is an excellent source of information. The Mining Journal, Ltd., also in London, publishes a weekly journal, a Mining Magazine (monthly), and a Mining Annual Review. The latter covers the field from three aspects: (1) by commodities, (2) through technical developments, and (3) geographically. The Industrial Minerals Directory 1977, 1st ed., Metal Bulletin Books, Ltd., London, provides addresses of organizations in the field. Other useful magazines and periodicals include Engineering and Mining Journal, Pit and Quarry, Rock Products, and World Mining, all published in the United States. In addition many new books related to industrial minerals have been published since the 4th edition of Industrial Minerals and Rocks. Most of these are included in the bibliography of each chapter in this volume. Another excellent information source is the proceedings of the Forum on Geology of Industrial Minerals. This group, which held its 18th annual meeting in 1982, is sponsored by a state geological survey or another mineral agency on a rotational basis. The proceedings have been published by the various sponsors and are available as indicated in Table 1. Two major sources of basic industrial mineral and rock data in the United States, and also a good source for many foreign countries, are the US Geological Survey and the US Bureau of Mines. The two agencies publish many reports and maps on a variety of geological and mining subjects. In addition, each agency has an indexed list of all their publications with a free service announcing new publications: New Publications of the Geological Survey, US Geological Survey, 329 National Center, Reston, VA 22092 and New Publications-Bureau of Mines, Publications Distribution Branch, US Bureau of Mines, 4800 Forbes Ave., Pittsburgh, PA 15213. The US Bureau of Mines (USBM) publishes annually Minerals Yearbooks which provide statistical data on mineral products including production, consumption, imports and exports, as well as information on new developments. Another very useful USBM series is called Mineral Facts and Problems. Editions were published in 1960, 1965, 1970, and 1975. Four major series of publications by the Bureau are Information Circulars, Reports of Investigations, Mineral Trade Notes, and Minerals and Materials. The last two are particularly good for news of foreign developments. The Bureau of Mines Employee Directory, available at all USBM offices, lists addresses and telephone numbers for all offices as well as same for all commodity and area specialists.

Jan 1, 1983

By L. D. Jaffe

From the limited experimental data in the literature, preliminary values were derived for the thermal diffusivity of titanium alloys and for the quenching severity of various mediums used in heat treating them. The thermal diffusivity, under quenching conditions, was found to be approximately 0.006 sq in. per sec. The quenching severity H for brine is approximately 8, for water 4, for oil 0.9, for air 0.08, and for argon 0.02 in. -' The quenching severity of the Jominy-Boegehold end quench water jet against titanium alloys appeared effectively infinite. Using these results, graphs were prepared showing ideal round sizes and Jominy positions having cooled conditions equivalent to those at the center and surface of titanium alloy rounds, plates, and sheets quenched in various media. THE importance of proper quenching of steel parts has long been recognized, and much quantitative work has been done on the subject. Recently, it has become evident that for titanium alloys, too, the rate of cooling from high temperature is important in obtaining high strength and hardness. Maximum hardness and strength may not be attained in the as-quenched condition but rather after a subsequent tempering or aging treatment. Nevertheless, if cooling from temperatures near the ß transus is too slow, for the hardenability of the alloy used, a soft a-ß structure will be produced which will not harden on subsequent aging.'-" The quenching of parts of practical interest can usually be approximated by simple shapes, such as cylinders (rounds) and plates (or sheets) of various thickness and combinations of these. A standard that has been used extensively for comparison purposes is the center of an ideal round: a cylinder quenched in a medium that instantly cools its surface to room temperature." For steel, considerable practical use has been made of the Jominy-Boegehold end quench hardenability specimen,".' and its value for titanium alloys is becoming evident. It therefore appeared worthwhile to attempt comparison of cooling conditions in titanium alloy rounds and plates of various sizes quenched in various media with cooling conditions in ideal round and Jominy quenches. These comparisons are based upon measurements reported in the literature. Quenching Severity of Jominy Water Jet and of Brine As one starting point, there were available the data of Phillips and Tobin8 for positions on a Jominy specimen having the same hardness as the centers of round bars of various size quenched in 5 pct NaOH brine, shown in Table I. The Jominy speci- men is a round bar, normally 1 in. diam and 4 in. long, quenched by a water jet at one end and air cooled on the other surfaces.' After quenching, hardness is measured vs distance from the quenched end on longitudinal flats ground 0.015 to 0.10 in. deep. The data of Table I were based on a subsized specimen of 3/4 in. diam. Since the positions tested are close to the jet quenched end, cooling there may be taken as due solely to the jet, and air cooling can be neglected. These positions are then equivalent to various locations near one surface of an 8 in. plate jet quenched on both sides. Assuming that the thermal diffusivity is constant and that Newton's law of cooling holds, temperature vs time curves at corresponding positions in Jominy specimen and round bar then may be calculated for various assumed quenching severities of the water jet and of the brine. Cooling curves are generally taken to be metallurgically equivalent when they show the same time to reach a temperature halfway between the initial (heat treating) temperature and the final (quenching medium) temperature.5 On this basis, using Russell's tables,9 upplemented by heat flow tables derived in similar fashion by the author for positions near the surface of severely quenched plates, it was found that the experimentally observed equivalence, Table I, was best matched if the quenching severity H of the Jominy water jet was taken as infinite (H = co). This means that the jet quenched surface should be considered as instantly cooled to the temperature of the water

Jan 1, 1956

By E. Teghtsoonian, K. G. Davis

THE preparation of cobalt crystals offers problems: on cooling through 400°C a phase transformation takes place whereby the structure changes from face-centered cubic to the low temperature close-packed hexagonal form. There are a few references in the literature which describe the preparation of cobalt crystals for magnetic work1,&apos; where melt-solidification methods were used. Reasons will be given why such methods were found unsuitable for our purposes. The following techniques were tried: 1) Solid state methods. Any mechanical shaping of tensile specimens would lead to uncertainty with regard to residual strains. With this in mind, following Kaa, strain-anneal and grain growth techniques were extensively investigated. In no Case were useful single crystals obtained. The transformation boundaries, which are crystallographically similar to twin boundaries, are probably extremely stable and inhibit the grain growth. 2) Growth from the melt. Normal melt-solidification methods were tried, using recrystallised alumina crucibles, and also a osoft moldo technique in which cobalt rod was packed in alumina powder. Trouble was encountered with gas evolution on solidification of the melt, giving porosity. Some adhesion of cobalt to the alumina also took place. Only a small proportion of the runs gave single crystals. 3) Zone-refining. Much the best results have been obtained using an electron-beam floating zone refiner. The refiner, based on a design by Calverly et Al .5 had a single-turn tungsten filament. It was operated at 600 v with an emission current around 45 ma. Commercial cobalt rod 1/8 in. in diam was given one pass at a rate of zone travel normally 25 cm per hr, under a vacuum approximately 10-5mm of Hg. Over 50 pct of the runs gave long sections of single crystal. Crystals up to 2o Cm long with good uniformity of cross section and straightness have been grown in this way. Increase in the length of the molten zone resulted in higher single-crystal yields, but control of zone stability was reduced. Sub-boundaries in the zoned crystals were few, and Laue X-ray spots were sharp. The success of the method is believed to lie in two factors, namely i) the absence of crucible restraints during the transformation, and ii) extreme axiality of heat flow during cooling. The axes of the zoned crystals were clustered around the [ 1010] pole, the pole of the basal plane being at least 60 deg from the specimen axis. Crystals grown at lower rates of zone travel showed the same orientation range, Fig. 1. This orientation is similar to that for other hexagonal metals grown from the melt, which is a little surprising when the mode of formation of the hexagonal phase is considered. The preferred orientation is probably caused by anisotropy of heat conduction, i.e., that crystal which can most effectively conduct heat away from the transformation interface will be favored. Fig. 2 shows the area on a standard cubic stereo-gram in which there are no poles more than 60 deg from one of the four < 111> directions. This area

Jan 1, 1962

By D. P. Harris

This paper surveys a few of the quantitative exploration models that might be of interest to an ex-plorationist seeking to apply methods of operations research to mineral exploration. A general development of each model is presented, and the model is evaluated relative to the exploration activity. Finally, a philosophy of exploration and mineral resources is presented, and a possible exploration strategy incorporating concepts of some of these models consistent with this philosophy is proposed. The high cost of conducting an effective exploration program has generated an increasing interest in methods of optimizing the allocation of the resources of a firm engaged in mineral exploration. As a step towards this, mathematical models have been formulated which are designed to quantify those variables of mineral exploration in such a manner that they can be integrated with all phases of the firm&apos;s operations so as to optimize its profit objective. QUANTITATIVE MODELS General: Exploration models express at least two concepts: mineral occurrence and effectiveness of search. In simplest terms, an exploration model might be formulated mathematically as follows: P(X) = F(X) . G(X), where P(X) = the unconditional probability of discovery of X deposits, F(X) = the probability of occurrence of X deposits, and G(X) = the probability of discovery of X deposits, conditional upon their existence in the search area. With these general models as a basis of reference, some of the specific exploration models are examined below. The Allais Model: DEVELOPMENT - M. Allaisl performed the first study in which a philosophy of exploration was formulated into a probability framework. His objective was to estimate the economic profitability of the exploration of the Algerian Sahara. Allais divided the Algerian Sahara into blocks of land (called cells) 10 km square and defined the random variable, X, as the number of mining districts per cell. Thus, F(X) would describe the probability of 1, 2, or n mining districts occurring within any cell of the search area. Allais reasoned that his best information as to the form of the distribution, F(X), was the number of mining districts per cell that had been found in well explored areas in the world, such as the Western States of the U.S. He found that the Poisson function produced a reasonably good fit to the distribution of districts in these explored areas: where? is a parameter, such as the average number of districts per cell. Thus, by determining the value

Jan 1, 1968

By J. R. Long, E. T. Hayes, R. S. Dean, F. S. Wartman

THE production of titanium in 15-1b. lots and with a purity sufficient to be consolidated into ductile metal, as described in a previous paper,1 has provided adequate material for a study of the : physical properties of titanium and a more thorough examination of its working qualities. Data on the physical properties reported in that paper were obtained on metal fabricated by a fixed procedure, standardized for the purpose of control of the reduction, and are representative only of material fabricated under those conditions. There are many possible variables in the working schedule, which will have significant effects on the properties of the finished material; and since the previous working methods were not necessarily the best, an investigation of the fabrication of titanium by other methods was undertaken. In this work the consolidation of the powder by pressing and sintering was conducted essentially as outlined in the report cited&apos; and all efforts were centered on fabrication methods for those powders and the properties produced by them. Hardness, density, microstructure, and tensile properties were determined at various stages in the working and annealing; and resistivity measurements were made on a few bars and drawn wire. [ ] CONSOLIDATION OF THE POWDER The screen analysis of the available titanium powder is given in Table I. No attempt was made to alter the size distribution from that noted because this powder, although coarse by normal powder-metallurgy standards, produced acceptable compacts suitable for the present work. Because of their large specific surface, finer powders are more contaminated by oxygen and produce harder compacts, which are difficult to work. The powder as produced is soft, compresses in a normal fashion, and exhibits very little tendency to adhere to the die surfaces. Unlike aluminum and magnesium powders, it can be readily pressed without the use of die lubricants. When compacted at so tons per

Jan 1, 1946

R. B. BrinSmade, Ixmiquilpan, Hgo., Mexico (written discussion*).—While agreeing with Mr. Gibson that his net-profit tax is the fairest and best for mines, I believe that the tax he describes can be more accurately defined by another name. In accounting, net profits are usually considered to be the residual of the gross income after operating expenses and the annual charge for upkeep of plant have been deducted. Even the necessary interest on bonds or mortgages should not be subtracted in this calculation, for this interest represents merely that fixed portion of the net profits going as a return to that fraction of the total property value owned by the bondholders. Applying this method of calculation to the gross income of a mining property, we should onIy deduct operation expenses and upkeep of plant to get the net profits on its whole property value. So Mr. Gibson in deducting a further sum, to cover the interest and amortization of the capital expended in mine development and equipment, really arrives at something quite differen&apos;t from net profits; which can properly only be defined as the annual value of the mineral in the ground, or the royalty value in miners&apos; parlance. From one viewpoint, Mr. Gibson&apos;s first principle, which assesses taxes, "proportionate to the benefits received by the person or property taxed," is identical with his third principle wbich assesses "with reference to the extent and value of the natural resources enjoyed." With one exception, everything of use around a mine represents a cash expenditure, or its equivalent in human labor, and state action has not added an iota to its value. The one exception is what makes the enterprise possible and it includes the mineral deposits and their associated surface; water and other landed rights. These natural resources are origin2!1y the gift of tile people acting through their agent, the state, and it is evident that a tax laid on whatever profits may arise from their enjoyment will be exactly "proportionate to the benefits received by the person or property taxed." Mr. Gibson is mistaken in his belief that the general property tax of the United States has the same incidence as his system of taxing profits, because the general property tax falls not only on land1 value—as does

Jan 1, 1920

By Frederic L. Kadey

Diatomite is a siliceous, sedimentary rock consisting principally of the fossilized skeletal remains of the diatom, a unicellular aquatic plant related to the algae. Thus, it has-been formed by the induration of diatomaceous ooze, and consists mainly of diatomaceous silica, a form or variety of opal which is first formed in the cell walls of the living diatom. Diatomaceous silica is not generally regarded as a synonym or the equivalent for diatomite, although it has been so used at various times. Accurately, diatomaceous silica is the preferred name for the principal mineral component of which the rock, diatomite, is composed. The terms diatomaceous earth and kieselguhr are used as synonymous with diatomite. The designations tripoli, tripolite, infusorial earth, etc., were used at one time but are now obsolete. With the changing nomenclature, these terms that were at one time correct when proposed and used for generations would be considered incorrect if used today in the light of current knowledge. The designation diatomite is reserved for those accumulations of diatomaceous silica that are of sufficient quality, size, and minability to be considered of potential commercial value. Processed diatomite possesses an unusual particulate structure and chemical stability that lends itself to applications not filled by any other form of silica. Foremost among these applications is its use as a filter aid, which accounts for over half of its current consumption. Its unique diatom structure, low bulk density, high absorptive capacity, high surface area, and relatively low abrasion are attributes responsible for its utility as a functional filler and as an extender in paint, paper, rubber, and in plastics; and as an anti-caking agent; thermal insulating material; catalyst carrier; and chromatographic support; polish, abrasive, and pesticide extender to name a few representative applications. The United States is the principal producing country, although diatomite is found in numerous other locations.

Jan 1, 1975

ASIDE from the John Fritz Medal, in which the Institute participates through its representation on the John Fritz Medal Board, the Institute itself has five major awards to make annually for excellence in technical papers, as follows: The Robert W. Hunt Medal, The Hadfield Prize, The J. E. Johnson Jr., Award, The Lewisohn Platinum Prize to senior members, and the President&apos;s Prize to junior members. ROBERT W. HUNT MEDAL The partners of Robert W. Hunt established a fund which was presented to the Institute at a fitting ceremony on May 27, 1920, to establish an annual medal and a sum of money to be awarded under the following rules: 1. The award shall consist of two prizes; first of a gold medal, second of a sum of money; a certificate to accompany each prize. The money prize shall not be awarded to. a member over 40 years of age, but under unusual circumstances, both prizes may be allotted to one person provided that he is not over 40 years of age. In general it will be understood that the Committee shall award the money prize to the younger men, rather than the medal. 2. The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or papers on iron and steel. The scope of the term "iron and steel" shall be determined by the sub-committee considering the awards. In general, papers dealing with the practical side of the subject have preference over those dealing with the theoretical side in recognition of the fact that Captain Hunt&apos;s main contributions to the industry have been in the improvement of production and quality of material. 3. A sub-committee of three to five including the Chairman of the Iron and Steel Committee, shall be appointed by the iron and Steel Committee annually to adjudge the award subject to approval. 4. The awarding committee shall submit its report to the Iron and Steel Committee at its October Meeting, and the. award be certified to the Secretary of the Institute in time to permit the presentation to be made at the Annual Meeting of the Institute. 5. The recipient of the award shall be designated "The Hunt Medallist." SIR ROBERT HADFIELD PRIZE Sir Robert Hadfield has offered an Institute prize of $1000 for researches with regard to the different forms of combination of carbon in iron and steel. Until within a few weeks no paper has been submitted which could compete for this prize. If the paper in hand should not meet the requirements, the donor has suggested that the prize be transferred and offered for: (a) the determination of the hardness in metals in connection. with super-hardness, (b) in consideration of questions of fuel economy, (c) in consideration of questions of industrial development and labor. J. E. JOHNSON, JR. AWARD This award is made from the income of a fund of $3000 donated by Mrs. Margaret Hilles Johnson in memory of her husband, J. E. Johnson, Jr., who was a prominent engineer, author of two valuable volumes on iron blast-furnace construction and practise, vice-chairman of the Institute&apos;s Iron and Steel Committee, and a frequent contributor of papers to the Institute&apos;s TRANSACTIONS.

Jan 1, 1925

By D. M. Dunbar

LONG before Columbus discovered America the original inhabitants toiled in the copper workings of the Andean Cordillera. Their best diggings appear to have been at Chuquicamata, site of the huge present-day open pit owned by the Chile Exploration Co., subsidiary of Anaconda Copper Mining Co. Located in Antofagasta Province of northern Chile, Chuquicamata is in the Atacama desert, high on the western slope of the Andes at 9500-ft elevation. In the Chuquicamata area the Atacama desert merges into the Cordillera. The climate is extremely arid and precipitation, either in the form of rain or snow, is very infrequent. The temperature varies from 50° to 85°F during the day, and drops to 20° to 40° at night. The Antofagasta and Bolivia Railroad, which connects the Chilean Port of Antofagasta with La Paz, Bolivia, passes within approximately 6 miles of the plant. A branch from the main line to Chuquicamata serves the property for outgoing copper and incoming freight. The distance to Antofagasta by rail is 163 miles. Previous to the Inca conquest, this region was inhabited by the Chuco Indians, a small tribe, descendants of the Aymaras and Quechuas. The Incas, whose capital was located in Cuzco, Peru, gradually extended their empire to the south, reaching at one time to what is now central Chile. It is believed that they built crude primitive furnaces on the banks of the Rio Salado where on a small scale they smelted copper ore from Chuquicamata. At the time of the subsequent Spanish conquest, legend has it that Diego de Almagro, on his return to Cuzco in 1536 after his invasion of Chile, obtained from these furnaces metallic copper for horseshoes. During the period from 1560 to 1879 the high grade veins of the Chuquicamata deposit were worked superficially by the Spaniards and Bolivians. The treaty signed after the war of 1879 recognized the sovereignty of Chile over this territory and Chile, realizing the importance of the district, started to develop it in an orderly manner, although only high grade veins were worked. New Process Is Key Reports on the deposit were brought to the attention of Albert C. Burrage, a Boston lawyer and financier, in 1910. Chuquicamata was described as a huge deposit of ore that was not amenable to the usual treatment by concentrating and smelting since much of the copper occurred as oxides. He had been working on a process for the recovery of copper from sulphide ore which involved a sulphating roast, leaching of the roasted product, and pre-

Jan 1, 1952

CONTENTS PAGE SOUTHWARD, GLENN B.-Coal Mining by the V System. Discussed by Glenn B. Southward, Howard N. Eavenson, Edward B. Raiguel, Thomas de Venny, J.. J. Rutledge, Graham Bright 1 ARMS, RAY W.-Dry Cleaning of Coal. Discussed by Ray W. Arms, S. A. Taylor, Howard N. Eavenson, W. R. Crane, F. F. Jorgenson, G. R. Delamater. 6 EAVENSON, HOWARD N.-Data About Labor Employed in Various Bituminous Coal Mines. Discussed by Howard N. Eavenson, George H. Ashley, E. A. Holbrook, S. A. Taylor, R. V. Norris 14 Coal Mining by the V System Discussion of the paper of GLENN B. SOUTHWARD presented at the New York Meeting, February, 1924, and issued as Paper No. 1300-C, with MINING AND METALLURGY, February, 1924. MEMBER.-How do you pay your men for loading? GLENN B. SOUTHWARD.-Everything is on time basis. MEMBER.-How many men do you have loading across one of the diagonal faces? GLENN B. SOUTHWARD.-From four to five, depending on the length of the face. Our loaders are so arranged that each will give about twenty-five tons per loader a day. MEMBER.-How much timber do you use? GLENN B. SOUTHWARD.-A little more than will be used in room-and-pillar work, but not a great deal more. We have not attempted to recover much of our timber. MEMBER.-IS the mine union or non-union? GLENN B. SOUTHWARD.-Non-union. HOWARD N. EAVENSON, Pittsburgh, Pa.-I went .through that mine some weeks ago, and think that the author has been very conservative in his statements about the amount of loadings, etc. EDWARD B. RAIGUEL, Huntington, W. Va. (written discussion).¬Page 7 shows 60 men employed in day and night shifts, inside the mine, producing 750 tons per day. Let us reduce these figures to a man-hour basis, for comparison with Mr. Eavenson&apos;s figures on West Virginia mines, as follows:

Jan 6, 1924

By Robert Rhea Goodrich

This research was done partly in the non-ferrous laboratory of the Department of Metallurgy of Columbia University, under the direction of Dr. Edward I?. Kern, and completed elsewhere. Acknowledgment is due to Prof. Arthur L. Walker, Dr. Edward F. Kern and Dr. William Campbell of the Department of Metallurgy, for their kind advice and for the inspiration derived from their instruction. This report is given under the following heads: Petrographic Description (Microscopic Study); Sampling and Preparing Ore for Treatment; Chemical Analysis; Treatment of Ore. Petrogeaphic DescRiption Texture: variable. Fine to medium mixed aggregate. Original Structure: Obscurc. Secondary structure: Fractured; healed. Mineralogy (Minerds are grouped for interpretation purposes and are arranged, in each group in approximate order of abundance)

Jan 1, 1916

By R. B. Woodworth

INTRODUCTION IN the sinking of bore holes, there are but two fundamental operations -drilling and hoisting,-which determine in the main the character of drilling mechanism and structures. There are endless ramifications, however, in the execution of these fundamental operations, according to the purposes for which the bore holes are drilled, their maintenance after completion, the protection and convenience of workmen, etc. The three main lines of use for bore holes are in mineral exploration, the sinking of water and salt wells, and the exploitation of petroleum and natural gas. This paper has to do more especially with the last. Here again there are many divergences. Wells may be drilled by either the percussive, the hydraulic, or the abrasive method. Finally, each of these methods, as applied by drillers of diverse nationalities, has followed somewhat different lines of development. The American system of cable-tool drilling has perhaps had the widest application; the hydraulic rotary is also in extensive use; but the Canadian system, the Galician system, and the Russian free-fall system all have their points of recognized merit and are preferred by operators accustomed to their use. These differences in drilling procedure, which rest ultimately on essential variations in geological conditions, are reflected in the chilling structures as well as in the drilling mechanism. The purpose of the present paper is to record those stages in the development of the application of steel to the construction of drilling mechanism and structures with which the writer has been intimately associated, and to contribute to the history of the art of drilling other data acquired in the course of his personal investigations. It is necessarily limited by reason of space to American practice, with especial reference, therefore, to the cable-tool system and the hydraulic rotary method of drilling wells for oil and gas.

Jan 11, 1915

By F. M. Lewis, J. F. Meyers

In the mining and handling of sulphide ores, some degree of oxidation takes place on the sulphide surfaces, which are exposed to the atmosphere. It is, moreover, well known that the oxidation compounds formed are a factor when such ores are subsequently treated by flotation. Modern operating technique and reagents are capable of contending with this condition to a major degree, provided that the proportions of the reagents used are varied correctly. This is particularly true at the Tennessee Copper Co., where the ore treated contains pyrrhotite in addition to other sulphides. A number of soluble salts, some of which are unstable, can be formed during the oxidation of the sulphide ores. Those unstable salts, whose oxygen requirements are unsatisfied, are constantly changing to more stable forms because oxygen reacts with them during the crushing, grinding and other operations of ore preparation. We add no chemicals of any kid to the ore pulp in its preparation for flotation feed. Consequently the only compounds that are present in the flotation feed are those produced by the natural oxidation of the ore in the presence of air and water. The Tennessee Copper Co. ore is composed of from 60 to 70 per cent sulphides and from 40 to 30 per cent non-sulphide material. It is not the purpose of this paper to discuss the nature of these various oxygen-sulphur compounds nor their effect on flotation, but to describe a method for correcting the effect. Suffice it to say that we have found that the reducing sulphur and oxygen salts have a depressing action on our bulk flotation process.&apos; From long experience we find that the best means of correcting for this variation in our work is to increase or decrease the quantity of xanthate, the promoting agent, as the quantity of the reducing salts increases or decreases. It was, therefore, very desirable to provide the operators with some quick and

Jan 1, 1947