Search Documents

By John S. Brown

IN 1925 the writer undertook a detailed statistical study of all producing areas in the Joplin district as a basis for evaluating programs and measuring objectives. For this purpose, the published figures in the yearly volumes of Mineral Resources were used, supplemented for earlier years by publications of the Missouri Geological Survey and other local and less official sources. When all else failed, the available data were projected backward to hazard a reasonable guess as to the unrecorded early output of important areas. Fortunately, the proportion of such prehistory production is not a large factor in any of the totals. These results were used during the next few years to measure the relative importance of various producing areas and to predict the peak period of development of the all-important Picher field. For the purpose of this review, the charts have been completed to the end of 1950. During World War 11, the U. S. Bureau of Mines became interested in a similar study and issued comprehensive statistical tabulations of data up to 1945 ( Info. Circular 7383), which have been checked against the figures used herein. This tabulation, however, does not include all the earlier data used by the writer nor does it offer any estimates of the wholly unrecorded era in the beginnings of the earlier camps. The area covered in this study is shown in Fig. 1 on which are indicated the relative location and approximate outlines of the principal producing camps. This also shows the approximate yield to date of each major camp in terms of combined lead and zinc concentrates. The output of zinc concentrates is roughly seven times that of lead. Hence, the economy of the district has depended primarily on the price of zinc, with lead as an important byproduct. Over much of the productive period, lead concentrates averaged about twice the value of zinc concentrates per ton, and in certain mines or areas the proportion of lead to zinc was substantially above average. The Joplin district is largely flat prairie but is partly moderately dissected, partially wooded land with a relief generally less than 100 ft. The rocks are almost flat-lying, nearly parallel to the surface, and the chief ore formation is the Mississippian Boone limestone, including its cherty phases. This formation either outcrops in the producing areas or is covered by a thin veneer of Pennsylvanian shales. Virtually all the ore occurs within 400 ft of the surface, and a large part at less than 300 ft in depth. Most of the land was divided into small farms or town lots before mineral development; tracts seldom exceeded 160 acres, and averaged considerably less. Mineral rights followed the surface ownership, segregation was rare, and a system of leasing for mineral development became well established early in the region's history, many landowners deriving small to sizable fortunes from royalties. Because of the shal-lowness of the ore and other factors, prospecting and mining was cheaper than in almost any comparable mining district in the United States. This situation, coupled with the widely divided land ownership, offered a fertile field for promoters and speculators and led to the rise of many small mining concerns. Only in its later history, under stern economic compulsion, has control tended to centralize in a few companies. Under these conditions, any important new discovery or successful development had much the effect of a gold rush or an oil boom. Every property in the area was leased quickly, promptly drilled, and, if ore was found, it was soon on the market. Many companies and individuals participated, and the average producing lease-hold probably was about 40 acres in extent. Any important field thus was attacked by anywhere from 10 to 100 or more producers. Production zoomed, eventually steadied or wavered, and ultimately subsided, leaving a desolation of tailings mountains, cave-ins, empty housing, and wreckage. The object of this paper is to depict the pattern of this process, so far as metal production is concerned, and to note the way in which it reacted to economic and political pressures. Production Charts In Fig. 2 is charted the production record, in tons of lead and zinc concentrates combined, of eight of the principal camps, which together account for approximately 99 pct of the total district production, over the years from 1870 to 1950. This period covers all but the very minor beginning of mining history. Two important camps are divided by state lines; hence, it has been necessary to combine production records for the two portions, based on estimates that may be slightly in error. Certain camps are sub-dividable into important units for which separate figures are available in whole or in part and have been charted as fractions of the major unit. The corresponding price of zinc is shown above all the charts. Three camps, Aurora, Neck City, and Galena, show a remarkably symmetrical graphic pattern, which is interpreted as the norm. The curves rise steeply to a peak, level off for an irregular interval, and then drop sharply to zero on a slope corresponding roughly to that covered by the initial rise. The three portions of these charts seem appropriately characterized by the designations of youth, maturity, and decline. On the whole, with some irregularities, the production in each of the three periods seems to be almost equal. A fourth camp, Granby, fails to conform to the normal pattern. It exhibits a very long period of reasonably uniform, stabilized production corresponding to maturity, followed by a rather precipitate decline. Its youth is hidden in the era of prehistory. This habit of steady, long-continued production at an even keel is attributable to the fact that this camp, more than any other, was controlled largely by a single principal owner at any given period over most of its history and this permitted the imposition

Jan 1, 1952

By Allen H. Rogers

THE need for coordinated effort on public problem by engineers has long been felt. Early in June there will assemble in Washington a conference composed of delegates from all the engineering organizations in the country. The call for this conference is issued by the Joint Conference , Committee of the four national societies as the completion of its work on the organization of a congress composed of delegates representing all the engineering organizations of the United States. The plan for this confederation was presented at a joint meeting of the administrative boards of the national founder societies on Jan. 23, 1920; and was unanimously approved in principle by that meeting. The work of the committee since that date has consisted in drafting a constitution of the organization to be presented at the conference for discussion and, after such amendments as may be adopted, acceptance.

Jan 1, 1920

By F. D. Wright

Production of a coal preparation plant is governed by many restrictions, such as the tonnage of different products and blends that can be sold within a given period, capacities and output proportions of the cleaning and sizing units, blending proportions, quality specifications, and costs and prices for the various products. Determination of the tonnage of each product and blend that should be made in order to obtain the maximum profit can be difficult unless a systematic method such as linear programming is used. In this paper the basic method of linear programming is described briefly. The Old Ben No. 9 preparation plant is used as an example to illustrate in detail how eqwations can be written to form a linear programming model of a coal preparation plant. Three sample problems, each requiring 56 or more equations and 63 structural variables, were solved with an IBM 650 computer. Linear programming is one of several mathematical tools used for operations research. It has been applied to many fields and has been used by a number of industries either to maximize the profits of certain operations or to minimize costs. P. B. Nalle and L. W. weeks' have described the use of the method by the Riverside Cement Co. to minimize the cost of blending raw materials to make portland cement. Their problem is to obtain at minimum cost a mix with certain specifications from a number of possible materials which have various costs and various amounts of CaO, SiO2, Fe2O3, and other constituents. In a paper on the use of linear programming by the National Coal Board in England, K. B. Williams and K. B. Halley2 describe how the transportation method, a variation of linear programming, is used to minimize the cost of sending 37 grades of coal from 28 mines to seven central washing plants which produce coal for furnace coke and foundry coke. The various coals have different percentages of volatile matter, moisture, sulfur, ash, and phosphorous, so there is considerable choice in how they can be blended to meet the specifications of the two products. The purpose of this paper is to show how linear programming can be used to maximize the profits of a coal washing plant which produces individual final products as well as blends. The Old Ben Corp. furnished assumed sample data from their Old Ben Mine No. 9 preparation plant for this investigation. However, the data that have been used are entirely the author's responsibility. METHOD OF LINEAR PROGRAMMING Numerous articles and books have been written on the theory and applications of linear programming.3-5 However, since the method has not been widely applied by the mining industry, a brief, nontheo-retical discussion of its basic method seems to be in order. Linear programming (Table I) is used to determine the best possible solution to a number of interdependent activities. It is essentially a method for making systematic selections from a number of possible solutions to determine positively the optimum solution. There may be other equally good solutions but no better ones. Each activity must have linear coefficients and there must be a criterion to judge how good the solution actually is. Linear programming is different from the solution

Jan 1, 1961

By Wesley G. Josephson

THE MINING PROPERTY of the Argonaut Mining Co., Jackson, Calif., is one of the oldest on the Mother Lode. A vein outcropping on a hill in this section could not long elude the eye of the forty-niner, so it was first discovered in 1850. From that time until 1893 the Pioneer mine, as it was then called, limped along under various poorly equipped and financed operators who tried tapping it by trenching and tunneling. Then the Argonaut Mining Co. took over the property and sank the present 65° inclined shaft in the hanging wall of the vein. The mine workings have now reached the 6000-ft. level, which is 5283 ft. vertically below the surface, or just 3 ft. over a mile. The total production of the mine is uncertain, because of lack of early records, but from 1893 to 1932 it is known to have produced in excess of $17,000,000.

Jan 1, 1932

"The zinc concentrator of the Butte & Superior Copper company, shown on the opposite page, represents an industry which is coming into importance in Butte. The existence of large bodies of zinc ore in some of the silver veins of Butte has been realized for years, but it is only recently that some of them have proved amenable to successful concentration. Most of the zinc ores thus far found in the camp are mixed with considerable pyrite, but those found in the Black Rock and Elm Orlu mines contain very little pyrite, so that a concentrate low in iron is possible.The Butte & Superior mill is rated at 1,200 tons daily capacity. The ore is sphalerite, most of which is finely disseminated through a hard quartz gangue, with small quantities of galena, pyrite, chalcopyrite, rhodocrosite and rhodonite. In mining, the included granite and the low grade vein matter are sorted out and used for waste filling so that the ore as it goes to the concentrator will carry about 20 per cent of zinc, 1 per cent lead, .25 per cent copper, 8 to 10 ozs. silver and a little gold. The ore bodies ranging from 5 to 103 feet in width, are mined by the square set method and filling of stopes with waste rock.The ore is hard and tough requiring extensive crushing and grinding equipment, consisting of Blake and gyratory crushers, 54-inch and 42-inch high speed rolls, Chili mills, Tube, and Conical mills. All of the lead con¬centrate and part of the zinc concentrate are recovered in the upper part of the mill by jigs and tables. The classifier overflow and the re-ground jig and table tailings go to settling tanks and from there to the Hyde Flotation process, where the balance of the zinc concentrate is recovered, and the tailing go to waste."

Jan 1, 1913

By J. J. Beeson

Page I. PrimaRy MineRalization............................................ 356 1. Introduction..................................................... 356 a. Scope of Work............................................... 356 6. Acknowledgments............................................ 357 c. The Bingham Mining District.................................. 357 d. General Geology.............................................. 357 e. The Utah Copper Mine....................................... 376 f. Field and Laboratory work.................................... 376 2. The Quartz-Monzonite.............................................. 377 3. The Pegmatite Veins.....:.•..............................:........ 378 4. The High-Temperiture Veins.........................-.............:379 5. The Early Hydrotherma! Period.:......................'............ 380 6. The Late Hydrothermal Period................................:.... 385 II. Seconuabx EnricuMENT............................................. 386 . 1. Author's Note;..... ;............................................ 386 2. Factors Governing Enrichment.....................................: 387 3. The Enrichment.................................................... 387 4. The Covellite Enrichment.; .:; ; : .:. :..:.............:................ 388 a. The Capping above the Covellite Ores:....:....................... 388 b. Conclusions Drawn. from a Study of the Capping and the Covellite ; Ores....,.............................................:.....,.' 392 c. Covellite Enrichment at Depth......:......................... : : 392 5. The Chalcocite Enrichment...................................... ; 394 a. The Carbonates in the Capping above .the Chalcocite Ores...:..: .. 394 ' b. The Formation of Chalcocite..:.:. :......:..'...........,......' 394 . 6. Secondary Chalcopyrite and Bornite.............................i ..., . 395 111.- Conclusions as to the Formation.oF the ImpoRtant Sulphides in the Disseminated ORes........................................,.......... 400 I. Primary MiNeRalization 1. Intrdtiction a. Scop. e .of Work.. first part bf, this paper deals with the country rock, its pegihatitic, pneumatolytic', and hydrothermal altektions; also, the effect of magnetite on the deposition of the primary chalcopyrite and pyrite.

Jan 1, 1916

By Zay Jeffries

Rearmament superimposed on buying sprees by the public, caused a general shortage of metals in 1911. and the rare metals were no exception; they also shared with the more common metals the uncertainty of future demand. In general, the apparent undersupply of metals is a favorable condition for the realization of sleeping possibilities of the rare metals, especially if the supply can he made sufficient to take care of the possible new demand. Many changes in metal usage in 1941 were forced because of shortages. When such changes are in the direction of the economic trend there is a speeding up in the tempo of the inevitable change, but when the forced changes are against the economic trend they are likely to be shortlived. In any event, the latter is not a solid foundation on which to build a future business.

Jan 1, 1942

By C. G. Grant, Wm. B. Price

This investigation of low copper-nickel silvers was untiertaken to check the work of Lèon Guillet on special brasses and to determine, more accurately, the effect of the addition of nickel on the mierostructure of the binary alloys of copper arid zinc. It was hoped that the results could be successfully applied to the practical production of low copper-nickel silvers. To explain the results of his investigations on special brasses, Lèon Guillet evolved his conception of "fictitious compositions." He states,' in his general conclusions, that on the introduction of a small amount of a third metal to a copper-zinc alloy, it enters into solid solution with the normal constituents up to saturation, but by so doing it brings the ternary alloy into a state microscopically equivalent to a binary copper-zinc alloy of fictitious composition, and physically more nearly like the latter than the brass containing copper-zinc in the ratio actually present. The physical properties of the ternary alloy, when compared to the same properties of an actual brass of the fictitious composition, are modified by the natural properties of the third element. Beyond the point of saturation, a special constituent appears and the above generalization no longer holds. For example, if a 60:40 brass has 4 per cent. of tin substituted for 4 per cent. of zinc, the actual composition would analyze 60:36:4. Assuming that 1 per cent. of tin plays the same part as 2 per cent. of zinc, the proportions of copper and equivalent zinc may be stated as 60 parts of copper and 44 parts of zinc, which, figured to 100 per cent., gives an analysis of 57.7 per cent. of copper and 42.3 per cent. of zinc, the fictitious composition for a 60:36:4 tin brass. The relation between ternary alloys containing copper and zinc together with a third metal, and the microscopically equivalent binary alloy of copper and zinc, may be expressed mathematically.

Jan 1, 1924

By S. J. Sindeband

Prior to discussing the metallurgy of sintered chromium borides, it is pertinent to outline some of the reasoning behind this investigation and the purposes underlying the work. This study was initiated as an aproach to the ubiquitous problem of a material for service at high temperatures under oxidizing atmospheres, and it was undertaken with a view to raising the 1500°F (816°C) ceiling to 2000°F (1093°C) or better. For the reason that no small, but rather a major, lifting of the high temperature working limit was being attempted, it was felt appropriate that a completely new approach be taken to this problem. A summary of the thinking behind this approach was published recently by Schwarzkopf.' In briefest terms, it was postulated that the following requirements could be set up for a material which would have high strength at high temperatures. 1. The individual crystals of the material must exhibit high strength interatomic bonds. This automatically leads to consideration of highly refractory materials, since their high energy requirements for melting are related to the strength of their atom-to-atom bonds. 2. On the polycrystalline basis, high boundary strength, superimposed on the above consideration, would also be a necessity. Since this implies control of boundary conditions, the powder metallurgy approach would hold considerable promise. Such materials actually had been fabricated for a number of years, and the cemented carbide is the best example of these. Here a highly refractory crystal was carefully bonded and resulted in a material of extremely high strength. That this strength was maintained at high temperature is exhibited by the ability of the cemented carbide tool to hold an edge for extended periods of heavy service. Nowick and Machlin2,3 have analytically approached the problem of creep and stress-rupture properties at high temperature and developed procedures whereby these properties can be approximately predicted from the room temperature physical constants of a material. The most important single constant in the provision of high temperature strength and creep resistance is shown to be the Modulus of Rigidity. On this basis, they proposed that a fertile field for investigation would be that of materials similar to cemented carbides, which have Moduli of Rigidity that are among the highest recorded. The cemented carbide, however, does not have good corrosion resistance in oxidizing atmospheres and without protection could not be used in gas turbines and similar pieces of equipment. It would be necessary then to attempt the fabrication of an allied material based upon a hard crystal which had good corrosion resistance as well. It was upon these premises that the subject study was undertaken and at an early stage it was sponsored by the U.S. Navy, Office of Naval Research. Since then, it has been carried on under contract with this agency. Chromium boride provided a logical starting point for such research, since it was relatively hard, exhibited good corrosion resistance, and, in addition, was commercially available, since it had found application in hard-surfacing alloys with iron and nickel. That chromium boride did not provide a material that met the ultimate aim of the study results from factors which are subsequently discussed. This, however, does not detract from the basis on which the study was conceived, nor from the value of reporting the results which follow. Chromium Boride While work on chromium boride proper dates back to Moissan,4 there has been a dearth of literature on borides since 1906. Subsequent to Moissan, principal investigators of chromium boride were Tucker and Moody,5 Wede-kind and Fetzer,6 du Jassoneix,7,8,9 and Andrieux." These investigators were generally limited to studies of methods of producing chromium boride and detennining its properties. Some study, however, was devoted to the chromium-boron system by du Jassoneix,7 who did this chemically and metal-lographically. This system is not amenable to normal methods of analysis by virtue of the refractory nature of the alloys involved, and the difficulties of measurement and control of temperature conditions in their range. Dilatometric apparatus is nonexistent for operation at these temperatures. Du Jassoneix made use of apparent chemical differences between two phases observed under the microscope and reported the existence of two definite compounds, namely: Cr3B2 and CrB. These two compounds, he reported, had quite similar chemical characteristics, but were sufficiently different to enable him to separate them. The easiest method for producing chromium boride is apparently the thermite process, first applied by Wede-

Jan 1, 1950

By H. Foster Bain

AFTER all, mineral sanctions are not a measure of peace, they are a measure of war, and we must regard them as such. We have had two examples now in the world-first, Italy, and secondly, Japan-where we have applied sanctions. When we got ready to apply sanctions to Italy that would hurt, they went to war. In the Far East, when we applied sanctions against Japan, in the latter part of 1941, there was a quick reaction, and the Japanese bombed Pearl Harbor.

Jan 1, 1944

By J. Burns Read, S. Tour

It is the purpose of this paper to summarize, as far as possible, the metallurgical information and experience gained by the Ordnancc Department, during the war, in the manufacture of artillery cartridge cases, to describe the tests to which artillery cartridge cases were put, and to summarize the knowledge and experience gained in this testing. The authors wish to acknowledge the aid given by manufacturers, army officers, and civilian employees of the Department in obtaining data. Artillery cartridge cases are cold drawn from circular disks punched from strips of rolled brass. The rnanufacture involves from 25 to 30 main operations, which are done almost entirely on a punch press. Descriptions of the operations have appeared in various periodical:: and, therefore, will not he given here. After each cupping, or drawing, operation, except the last, the cases are annealed at from 540" to 650" C. (1000" to 1200°F.), to remove all the hardening stresses set up in the metal and to allow complete recrystallization. After each annealing, the cases are pickled in niter cake or sulfuric-acid solution and then washed in water to remove all traces of acid. In some instances, the cases arc then immersed in a cyanide-salt solution, and afterwards rinsed in water, to remove the thin layer of copper that forms on the surface of the cases during the acid pickle. The last cold-drawing operation is followcd by the heading operation which, by flattening the head of the case on the outside, causes the metal to flow on the inside to approximately the proper finished dimensions. The mouth, or open end, is then annealed at 430" to 450" ('. 1800" to 900" F.) by immersion in a salt bath or by gas flames. After being washed, the eases are tapered, when they arc ready for machining, inspection, and testing. Cartridge-case Disks Good disks of proper composition and physical properties are essential to the production of good cartridge cases. The Ordnance Department

Jan 1, 1923

By J. Burns Read, S. Tour

It is the purpose of this paper to summarize, as far as possible, the metallurgical information and experience gained by the Ordnancc Department, during the war, in the manufacture of artillery cartridge cases, to describe the tests to which artillery cartridge cases were put, and to summarize the knowledge and experience gained in this testing. The authors wish to acknowledge the aid given by manufacturers, army officers, and civilian employees of the Department in obtaining data. Artillery cartridge cases are cold drawn from circular disks punched from strips of rolled brass. The rnanufacture involves from 25 to 30 main operations, which are done almost entirely on a punch press. Descriptions of the operations have appeared in various periodical:: and, therefore, will not he given here. After each cupping, or drawing, operation, except the last, the cases are annealed at from 540" to 650" C. (1000" to 1200°F.), to remove all the hardening stresses set up in the metal and to allow complete recrystallization. After each annealing, the cases are pickled in niter cake or sulfuric-acid solution and then washed in water to remove all traces of acid. In some instances, the cases arc then immersed in a cyanide-salt solution, and afterwards rinsed in water, to remove the thin layer of copper that forms on the surface of the cases during the acid pickle. The last cold-drawing operation is followcd by the heading operation which, by flattening the head of the case on the outside, causes the metal to flow on the inside to approximately the proper finished dimensions. The mouth, or open end, is then annealed at 430" to 450" ('. 1800" to 900" F.) by immersion in a salt bath or by gas flames. After being washed, the eases are tapered, when they arc ready for machining, inspection, and testing. Cartridge-case Disks Good disks of proper composition and physical properties are essential to the production of good cartridge cases. The Ordnance Department

Jan 1, 1923

By Edward C. Roper

Pegasus' Gold Ltd. operates two gold/silver heap leaching operations in the Little Rockies area of Montana. The Little Rockies has produced gold from underground operations on an intermittent basis from the 1880's to the early 1950's and from the open-pits on a continuous basis since 1979. Run-of-the-mine ore is drilled, blasted, sorted, loaded and hauled. The waste is dumped and compacted into 30 meter (100 foot) fills to be used for future leach pads. The leach pads have a central drain system and the impermeable membrane is constructed of bentonite and 30 mil PVC. The plants which have beenexpanded to 4900 Ipm (1300 gpm) capacity use the Merrill-Crowe process for gold and silver recovery. 4600 liters (1200 gpm) of the 9500 Ipm (2500 gpm) spray capacity is recycled through the old leach pads for upgrading before being processed. The gold/silver precipitate is smelted and the resultant dore' is shipped to a buyerhefiner. 1983 projected production is 2,177 kg (70,000 02s) of gold at a cost of less than $10/gm.

Jan 1, 1984

By W. Spencer Hutchinson

THE purpose of this account is to introduce to other engineers and geologists who use photography a means of interpreting topographic and geologic structure with the stereoscope. Anyone who finds this of sufficient interest to read it at all must cut out the pictures shown and have a good look at them through the stereoscope; there is no other way to appreciate what is meant. Most of us have been disappointed by the flatness of mountain pictures and by the lack of perspective in photographs taken to illustrate topographic and geo- logic features. The use of the stereoscopic principle was suggested by the work of the photographic division of the Air service during the war. Photographs of the battle line, taken from air planes, were mounted for stereoscopic study, with most remarkable development of topography, penetration of camouflage and, by the matching of pictures with a time interval between, sure revelation of new work by the enemy. Thus, two views taken from a plane flying at 10,000 ft., both of the same terrain but from different points, are mounted in proper relation and put into the stereoscope. If the distance between the two positions of the camera was 200 ft., the observer then sees the topographic and military features as though his eyes were 200ft. instead of 235 in. apart.. The result is startling in its revelation of features that are flat and unintelligible when viewed by the unaided eye or in a single photograph. The technic of the work, as developed during the war, was quite complex and

Jan 1, 1921

By Charles Will Wright

DESPITE the war, the First Pan American Mining Congress, held in Santiago, Chile, Jan. 15-23, was attended by about 300 persons including the official delegates from sixteen of the American republics. The United States delegation consisted of Elmer Pehrson, of the U. S. Bureau of Mines; D. F. Hewett, of the U. S. Geological Survey; William H. Hobbs, of the Carnegie Foundation; and C. W. Wright, delegate of the Board of Economic Warfare and of the A.I.M.E. Mr. Wright was elected to head the delegation. Among the other members were Edward Steidle, of Pennsylvania State College and also an official A.I.M.E. delegate; John Huttl, of Engineering and Mining Journal; W. 0. Vanderburg, foreign mineral specialist from Lima, Peru; O. B. Hundley, of the American Cyanamid Co.; Horace Graham, of the Anglo-Chilean Nitrate Co.; and several officials and engineers from the Anaconda, Kennecott, and Bethlehem Steel companies' mines in Chile.

Jan 1, 1942

By W. R. Bull, J. R. Roos

A method is described whereby the true financial value of each constituent of each concentrate can be calculated. Each value is then compared with what this value would be in a perfect separation. The difference in each case represents the loss incurred by each aspect of an inefficient separation. The relative magnitudes of these losses indicate those avenues of plant investigation and research that offer the highest potential reward. The metallurgical efficiency of a concentration operation is difficult to express because there are two criteria of performance, namely, grade and recovery. Neither of these alone gives any indication of the effectiveness of an operation and, if they are combined in some formula, it must be empirical and unreliable because of many external factors. Since milling is an operation performed as one step in the most profitable overall method of producing a metal or other end product, the main objective of mill operation should be to make a maximum contribution to this maximum profit. When concentrates are sold to custom smelters, the income from the operation, and the costs, may be calculated. When concentrates are further processed by another division of the same company, and there is no formal financial relationship between, say, the milling and smelting divisions of the company, the mill superintendent's job is less well defined. But even so, if the mill superintendent works as though he were selling his concentrates, and uses reasonable, if fictitious, conditions of sale, then he can get a good indication of the effectiveness of his operation by calculating his "Economic Recovery". ECONOMIC RECOVERY This is a method used as a basis of operation by several mills and has been described in the literature. Very briefly, the "standard" of operation is taken as that of a mill separating the ore into perfectly pure concentrates with 100% recovery of each mineral in its respective concentrate. For example, a 4%Pb, 4% Zn ore (galena and sphalerite), would provide a lead concentrate weighing 4.62% of the feed and assaying 86.6% Pb and a zinc concentrate weighing 5.97% of the feed and assaying 67.1 % zinc. These perfect concentrates are (hypothetically) shipped to the appropriate smelters, freight and treatment charges and payments calculated, and the net return obtained. This is the optimum financial return for the operation of the mill and is used as the standard. Now the return for the actual, real-life, mill operation is calculated in the same way, and the ratio of the two is termed the Economic Recovery. Many additions and modifications may be made in any particular case. For example, if the zinc mineral is marmatite, the optimum grade of the zinc concentrate may be set lower than 67.1%. If silver is present, it will be recovered 100% in the lead concentrate in the perfect operation. Similarly, cadmium will be recovered 100% with the sphalerite. Mr. Weiss' paper' mentions a case where, because of extremely fine intergrowth between the valuable mineral, chalcocite, and pyrite, the optimum grade of copper concentrate was taken as 45% Cu instead of the theoretical 80%. Each operation will present its own possibilities in this way.

Jan 1, 1970

By Samuel H. Dolbear

THE purpose of a technical report is to record facts, usually collected by investigation, and to interpret these facts in understandable language. The audience may range from a small shareholder without technical knowledge, to a highly trained engineer or geologist. If the client is a mining company with technically trained executives, the report writer's problem is relatively simple. The writer will then be appraised not only for his conclusions, but for clarity of language and organization of the report. If the writing is bad, the construction careless, and there is a failure to clearly convey to the reader the facts and the author's conclusions, the report is a failure and the writer may have damaged his professional character. Spoken words die quickly, written words may constitute a permanent record and if they are badly composed they may rise up to damn the author. "A good measure of an author's understanding of his subject is his ability to express it clearly in plain words." Good English Teachers in the fields of mineral technology have frequently complained that even in post-graduate groups there is an appalling indifference to their appeals for good English. Some have even noted a student's belief that the use of refined English is effeminate. If those with such immature beliefs could measure the pay-check damage arising from the use of "sloppy" language, they would realize that precision and refinement in English may be quite as important as technical accuracy. When the reader audience is without technical knowledge simplicity in treatment becomes especially important. If one is engaged in consulting work, in government service, or in any field where reports have public distribution, the language employed should be technically adequate but simple enough to be understood by non-technical readers. For example, one may use the term "visual" in place of "megascopic." Technical language can be so obscure that it cannot be understood even by highly-trained students. In the March-April (Vol. 47-No. 2) issue of Economic Geology, Nicholas Vanserg ridicules these extremes and quotes various paragraphs from published material, such for example: "However, lattice orientation unaccompanied by cognate dimensional orientation can never be attributable to growth from an isotropic blastetrix." "The temperature declines because of cessation of the exothermic chemical and mechanical equilibriopetal processes." These he calls "good geologese" and they are calculated not only to baffle the reader but to impress upon him the erudite character of the author. Revision In some cases, difficulty arises from the fact that the writer is too close to the subject and unconsciously assumes that his reader is equally familiar with the background of the report. It is difficult for the writer to regard his work objectively and to determine to what extent it is likely to be understood. Every important manuscript will gain in clarity if the author will have it reviewed by an informed reader. But the writer must not be oversensitive to criticism and should not treat his composition as perfect and beyond the possibility of improvement. The first draft of a report always requires revision, regardless of the care used or the ability of the writer. Three or four revisions are not uncommon. The first draft usually requires expansion in places, the deletion of non-essential material, and language changes to promote clarity of expression. This should be done by the author after a lapse of time, even if only overnight, in which his mind has been occupied on some other subject. Possible improvements are always more visible. The manuscript should be passed on to another reader for further suggestions. Organization of Material The engineer should study available reports and library references before going into the field. If the previous reports have been responsibly done and can be accepted as correct, then much field time can be saved. It is, of course, customary to make some on-the-ground checks to confirm earlier reports, particularly those relating to ore reserve which may have undergone changes. Report writing requires time and expense, but nevertheless, the basic reasons for conclusions should be presented even in the case of a worthless property, for it may prevent a duplication of the work. If the mine examined is obviously of no further interest, no useful purpose can be, served by preparing a report in detail. In one case an engineer travelled all the way to South America only to find that the mine had been grossly misrepresented and was valueless. His cabled report "Nonsense" is a case of over-simplification, but it served his company's purpose. The first step in report organization should be the selection of subjects. This should be done at the mine, and the data collected for each subject should be reviewed in considerable detail on the ground. Otherwise one may find that he has failed to collect some essential details not readily obtained after he has returned to headquarters. If the property to be described is undeveloped, then many of the subject titles are automatically eliminated. Usually no useful purpose is served by an attempt to calculate the cost of production under such circumstances, although the cost of exploration

Jan 1, 1952

By James Douglas

Discussion of the paper of James Douglas, presented at the New Haven meeting, February, 1909, and published in Bulletin No. 29, May, 1909, pp. 439 to 451. JAMES DOUGLAS, New York, N. Y. (communication to the Secretary*) :-In my paper on the Conservation of Natural Resources, I referred to the slow replacement of bee-hive ovens by the by-product ovens as a most notable instance of waste. And I quoted from Mr. Parker's report for .1906 an explanation given by him in accounting for the small production of by-product coke. It was that the markets for the by-products of the coke-ovens was so limited that some of the ovens constructed were out of operation. His report on the manufacture of coke in 1908 1 does not record an improvement, and attributes the strange fact that we alone, of all the industrial peoples, delay the adoption of this cardinal improvement from the continuance of the same almost inexplicable cause. To quote again from his report, lie says (p. 241): "The year 1908 was not marked by any notable gain in the construction of by-product coking plants, though some new work was done. There was a net increase of 115 in the number of completed ovens in 1908 over 1907, the totals for the two years being, respectively, 3,892 and 4,007. The additional equipment consisted of 140 Koppers regenerative ovens built at Joliet, I11., by the United States Steel Corporation, but this increase was partly offset by the dismantling of Y5 Semet Solvay ovens at Sharon, Pa., the net gain being 115 ovens. Included in the total of 4,007 completed ovens in 1908 are 152 Newton-Chambers ovens at Vintondale, Pa., but as no recovery of by-products was made at this plant in 190S, the production of coke is included with that from beehive ovens. The 56 ovens of the same type at Pocahontas, Va., have not been in practical operation since they were first. installed. In addition to these there was one other by-product plant of 120 ovens. Oat. was not operated during the year. The number of retort ovens producing coke in 1908 was 3,679, as compared with 3,811 active ovens in 1907." In describing the anomaly he says (p. 249): It has been contended that the development of the by-product coking industry would have shown more rapid progress if markets for the by-products were * Received Feb. 2, 1910. Mineral Resources of the United States for 1908, Part I1., U. S. Geological Survey (1909).

Apr 1, 1910

By R. C. FLEMING

G OLD MINING is enjoying a real revival in the West, and a considerable portion of the production is coming from small properties. The large mining companies of the world get most of the publicity, but in the last year the small gold property has often proved a more attractive field for the mining engineer looking for something to do. Old mines have been re- opened, prospects have been more closely examined, and many properties that were out of the running with the high commodity and labor costs of two or three years ago, have recently been making money for their operators. An interesting phase of this activity is the operation of so-called one-man mines. The west is dotted with these small properties, without the resources or reserves to warrant large-scale operation, but which return a living and often something over to one or two men who under- stand mining and simple methods of treatment.

Jan 1, 1932

By R. W. Heckel, R. L. DeGregorio

The DeHoff method of determining the size distribution of ellipsoid-shaped, second-phase particles has been applied to the spheroidization of cementite in a eutectoid steel. The surface area of Precipitates determined from the various size fractions in the distribution was correlated with surface-area measurements based on the number of intersected interfaces on a random lest line. The precipitate particles were found to be oblate ellipsoids with an axial ratio of about 0.90. The size distributions were found to be log-normal. A method is proposed whereby the shrinkage of small particles and growth of large ones can be determined from the experimental data. The experimental data are compared to previously proposed mathematical models describing diffusion-controlled kinetics and various types of interface-controlled kinetics. The experimental growth and shrinkage rates are considerably slower than those predicted by diffusion-controlled kinetics. The best fit is obtained for a model describing interface-controlled kinetics limited by the rate of formation of cementite at the growing interfaces where the interfacial reaction rate is proportional to the solute thermodynamic activity gradient across the surface. THE subject of spheroidization of second-phase particles has been considered previously by other investigators. Livingston1 has studied the precipitation of the cobalt-rich phase from copper alloys containing 0.7 to 3.2 wt pet Co. His results indicate that the average particle size increases as the cube root of the heat treatment time in accord with diffusion-controlled kinetics.'-' Komatsu and rant' in their studies of the growth of SiO2 in a dispersion-strengthened copper-silica alloy found that the initial growth of SiO2 proceeded by diffusion-controlled growth and later stages were limited by interface-controlled growth. The values of the activation energy obtained for the interface- controlled process led them to the conclusion that the process was limited by the dissociation of SiO2 at the shrinking interface. The transition from diffusion-controlled growth to interface-controlled growth was characterized by a particle size which varied with the heat-treatment temperature. It is also interesting to note that the particle-size distribution as found by Komatsu and Grant exhibits log-normal behavior when replotted on log-probability coordinates. Dromsky, Lenel, and Ansell9 have observed the growth of Al2O3 particles having a mean free path of about 1.5 to 13 µ. Their photomicrographs indicate that the Al2O3 particle sizes were larger than those observed by Komatsu and Grant. Dromsky, Lenel, and Ansell concluded that the Al2O3 coarsened by an interface-controlled growth mechanism limited by the solution of A12O3 at the shrinking interfaces. Bannyh, Modin, and Modin10 have studied the spheroidization of a eutectoid steel (0.83 wt pet C). Their spheroidization (tempering) treatments were carried out in the range from 210o to 700°C for times between 1.5 sec and 20 hr. Measurements of mean particle size as a function of time indicated a cube root of time dependence of size at 700°C, in agreement with previous analyses of diffusion-controlled kinetics.2°7 At lower temperatures, the time dependence was less than the one-third power. It is important to note that, although mathematical models of growth* considering particle-size distribution have been available, measurements of only mean particle size have been carried out. DeHoff11 has presented a quantitative metallography technique which is applicable to the determination of the size distribution of ellipsoids of constant shape. This method is applicable to both oblate and prolate ellipsoids of all ratios of minor to major axis and is based upon an extension of Saltykov's analysis12 of the distribution of spheres of varying size. DeHoff's analysis is based upon measurements of the minor axis of the particles on a random plane of polish in a unit area. This method provides a measure of the number of ellipsoids in various size ranges per unit area. As pointed out by DeHoff, such measurements may be used to obtain surface area and total precipitate volume data. Thus, the accuracy of the distribution analysis may be checked by comparison of the surface and volume

Jan 1, 1965