Search Documents

By Victor J. Miller

The Northeast Tripp Slide is one of the larger slope failures that can be attributed to open pit mining. It is a 11.7 million cubic meter (15.3 x l0 6 yd3) wedge failure created by two thick gouge-filled fault zones whose intersection plunges into the Tripp pit at 13°. One unique aspect of this failure is that the slide is now stable despite having moved an estimated 8.5m (28 ft.) towards the pit and having reached a maximum overall velocity of 2lmmlday (0.07 ft/day). The slide started to fail in 1968, accelerated until mining in the slide's toe area was halted in April 1970, then began to decelerate. With the cessation of mining in the toe area, rubblized rock sloughed into the pit bottom which added weight to the failures toe constraints and began the stabilization process. Measurements from a network of survey stations revealed a correlation between the slide's velocity and heavy precipitation. Runoff water accumulating in the tension cracks is believed responsible for this correlation. Moreover, the survey net measurements showed that during the failure's last stage the vertical component of the slide's movement greatly increased. It is proposed that this settling was caused by plastic-like flowage of the clay gouge underlying the failure The fault zone's effective shear strength was estimated by a back- analysis on the wedge's geometry and by performing direct shear tests. The tests, performed on cores taken from samples that were collected on the failure, yielded a residual shear strength of: cohesion 0.61 kg/cm2 (8.7 lb/in2), and a friction angle of 9.6°. This residual shear strength was near1y equal to the back-calculated strength indicating that the controlling fault's effective strength was essentially the same as the residual shear strength of the gouge filling

Jan 1, 1983

By Christopher Haycocks, Lawrence P. Johnson, George M. Neall, James M. Townsend

No method of roof control yet devised has proven to be universally acceptable for the wide range of strata conditions experienced in U. S. coal mines. However, a relatively new innovation, the roof truss, has proven itself capable of preventing roof failures which both conventional and resin bolting could not. Presently, the economics of roof trusses are not favorable when compared to bolting due primarily to drilling and installation procedures, but this is expected to change with improved truss and equipment designs. To realize the full potential of this new method of roof control, design criteria are needed which can optimize the effect of the truss for varying strata conditions. A review of the literature reveals that some work has been conducted on the roof truss. Cambrell and Haynes1 (1970) showed that the roof truss is superior to angled roofbolts installed through a header. Sheorey, Verma, and Singh2 (1973) used statics to prove that the optimum angle of inclination should be greater than 45°. However, to date, no systematic attempt has been made to establish design criteria. In this paper, the problem was approached in three ways. First, model studies were performed to determine general trends of truss support as a function of a number of variables. This provided a better understanding of the support mechanism involved. Secondly, beam theory was employed to calculate the actual support capacity of a truss, realizing the many simplifications, assumptions, and shortcomings of this approach to such a complicated problem. Last, field testing will be utilized to test the hypotheses previously developed and provide hard data to further synthesize roof truss design criteria. Field testing has recently commenced and should be complete before mid 1977.

Jan 1, 1979

By R. W. Jenkins, O. J. Neslage

The need for mechanized drilling to decrease mining costs has resulted in the development of the jumbo from column-and-bar drill carriages to hydraulically controlled jib jumbos. Resultant savings from use of improved jumbos have been high enough usually to retire the machinery investment within a year. The jib jumbo unit has been applied successfully to development and preparation programs and flat-bedded stopes, and an even wider field is forecast for its use.

Jan 1, 1950

By GUY B. HUNNER

THOSE magnetite ore bodies comprising the Clifton Mines are situated in the south central part of St. Lawrence County, New York, on the western slope of the Adirondack Mountains. The topography is made up of gently rolling hills densely wooded with second-growth maple, birch, and hemlock. Drainage is north and west to the St. Lawrence River.

Jan 1, 1943

Abbey, Robert Graham, District Mgr.. The W. W. Sly Mfg. Co., 50 Church St.. New York, N. Y. '21 Abbott, A. N., Mines Supt., Mazapil Copper Co., Ltd Concepcion del Oro, Zac., Mexico. '28 Abbott, Argyle Campbell, Dev. Dept., E. I. du Pont de Nemours & Co., Wilmington, Del. '29 Abbott, Clarence E., V.P., Charge of Raw Materials, Tenn. Coal, Iron & R. R. Co., 1242 Brown-Marx Bldg.. Birmingham, Ala. '04 Abbott, Louis Benjamin, Chief Engr., Elkhorn Div., Consolidation Coal Co., Jenkins, Ky. '16 Abeel, George H., Jr., Cons. Min. Engr Box 427, Santa Monica, Cal. '18 Abel, Albert E., Asst. to Pres., Valley Mould & Iron Corp Hubbard, Ohio. '19 Abel, Raymond L., Asst. Prof., Dept. of Pet. Refin., Univ. of Pittsburgh Pittsburgh. Pa. '28 Abeel, Leo M., Research Engr., Sullivan Concentrator Chapman Camp, B. C., Canada. '31

Jan 1, 1932

By AIME AIME

IT its annual meeting on Oct. 21 and 22, the Engineers' Council for Professional Development announced the selection of J. P. H. Perry. vice-president of the Turner Construction Co. and prominent civil engineer of New York City as its new Chairman. He succeeds C. F. Scott, who becomes Chairman of its Committee on Professional Recognition. S. L. Tyler, Secretary of the American Institute of Chemical Engineers, succeeds A. B. Parsons as ECPD Secretary. R. E. Doherty is Vice-chairman. C. E. Davies remains as Assistant Secretary, as do R. L. Sackett as Chairman of the Committee on Student Selection and Guidance, O. W. Eshhach as Chairman of the Committee on Engineering Training, and Karl T. Compton as Chairman of the Committee on Engineering Schools.

Jan 1, 1938

By AIME AIME

THE Board of Trustees, made up of three from each of the four societies, conducts the business com- mitted to United Engineering Society by its Founder Societies under its Charter, the Founder's Agreement and the Library Agreement. A draft of a budget of revenue and expenditures for the ensuing calendar year is presented each September to the secretaries of the Founder Societies for the information and comment of their governing bodies. After revision, the budget is adopted, by the incoming Board of Trustees at its meeting in January.

Jan 1, 1929

By Francis Church Lincoln

I. SITUATION AND SURROUNDINGS. THE Promontorio mine is situated at the northern end of the Sierra San Francisco de Coneto, in the town of Promontorio, Partido of El Oro, State of Durango, Mexico. As shown in the sketch-map, Fig. 1, the nearest railroad station is Chinacates on the Mexican International Railroad, 82 miles north of the city of Durango. The mine is 16 miles north of the station by air-line. It is reached by means of a good wagon-road which first crosses the Guatimapé Plain, passing the ranches of San Antonio and San Julian, to Estacion-a distance of about 15.5 miles-and then entering the mountains crosses the Sierra to Promontorio-a further distance of 11.5 miles¬making in all a distance of 27 miles by road from railroad to mine. Promontorio is just beyond the summit of the range, at an elevation of about 8,000 ft. above sea-level, or 1,350 ft. above the Chinacates station. The Castillo de San Francisco, the highest peak in the Sierra, has an altitude of 10,000 ft., and the Promontorio road crosses the summit of the ridge at an elevation of 9,000 ft. by a pass just below this peak known as the Puerto del Almagre. The Promontorio mill is situated at Santa Ives, 2 miles by tram or 3 miles by wagon-road to the north of Promontorio and about 600 ft. lower. The Sierra San Francisco de Coneto decreases in height towards the north and west till it comes to an end at the Melchor Arroyo on the ranches of Melchor and Ramos. Beyond this arroyo another range, the Sierra de la Candela, begins. In the vicinity of the Promontorio mine the hills are very rugged and the surface is furrowed by ravines which contain running streams during the rainy season-July, August and

Jan 1, 1908

By Hiland G. Batcheller

HISTORY shows that the nation which makes the most steel is the most likely to win wars. Today the course of war shows that the nations which get there first with the most steel of the right kind will be the ones to win. Not only the most steel, mind you, but the right kind. Adequate production, which was enough for victory before the days of totally mechanized warfare of 1943, must now be accompanied by still better quality as well as more effective distribution. Further, both production and distribution must be flexible enough to permit rapid shifts from one weapon to another for use in varying elements in varying geographical areas. Thus the problem of making enough steel of the right kind at the right time in the face of changing requirements dictated by experience has been and will remain highly complex. This does riot permit us to ease our restrictions on nonessential use. War is a complex business, like the job of making steel for war. Each time we solve one problem, another pops its head up. Yet we are making some progress.

Jan 1, 1943

By C. Chamberlain

The Telfer Project, Australia's newest, largest, and most remote gold mine treats 480 kt of ore grading 9.33 g/t derived from open pit mining operations. Coarse gold is recovered by gravity concentration with jigs and further upgraded wing a continuous strake launder table, and by amalgamation. Remaining gold is recovered in a cyanide circuit and incorporates flat bottom air agitators, counter current decantation (CCD) and stellar filters for clarification and precipitate removal. Overall recovery into a bullion averages 98%. The mill incorporates a number of design features that allow for maximum efficiency and security wing a minimum number of operation personnel.

Jan 1, 1983

R. W. Raymond, New Pork City: It seems questionable to me whether Mr. Mezger's identification of the rock-structure he describes, as the Augengneiss of previous authors, is warranted by the definitions given by them. Naumann (1854)t describes Augengneiss as a porphyry-like variety, " which has assumed, by reason of single large kernels or granular concre-

Jan 1, 1896

By WM. HUFF WAGNER

Computations and allowances for mine depletion for Federal income tax purposes depend upon the meaning of certain terms in the pertinent provisions of section 114(b) 4 of the Internal Revenue Code. Unfortunately, but one of these terms is defined in the Code. Congress left it to the Commissioner to define the other terms in the Regulations. Even though the Commissioner, through his staff, labored long and earnestly to draft these definitions they have not been satisfactory to the mining industry, because the definitions in the Regulations and the interpretation placed thereon by the Commissioner do not state what the industry believes to be the clear and obvious intent of Congress. Consequently serious and prolonged disputes, unduly delaying the settlement of Federal tax returns involving percentage depletion deductions are continually arising between taxpayers and the Commissioner.

Jan 1, 1949

By John T. Crawford

Introduction Loading and hauling systems are evaluated in open pit mining for new properties, expanding existing operations, changing systems or equipment, and equipment replacement analysis. The objective of such evaluations is to determine the equipment needed to handle planned tonnages at the lowest cash flow cost. Cash flow costs are used to combine capital outlays with operating and maintenance costs. Leasing costs could be substituted for capital costs with appropriate modifications to calculation procedures. These modifications will not be covered. This chapter will describe methods of evaluating loading and hauling systems, concentrating on some of the more often raised questions concerning quantitative data. While the methods described are not the only ones in current use, they have a record of proven reliability. The shovel and haulage truck system is used In the examples because of its common use in open pit mines. In medium to large open pit mines, electric shovels and diesel-electric drive haulage trucks are normally used. The basic ideas presented in this chapter apply to all loading and hauling systems, with appropriate modifications. The process of performing a shovel and haulage truck evaluation can be time-consuming and tedious because of the quantity of data involved, but it is not particularly difficult. The examples used to Illustrate shovel and haulage truck evaluation are based on a hypothetical open pit mine operating 350 days per year producing 31 750- 000 t (35,000,000 st, 100,000 stpd) annually, of which 11 110 000 t ( 12,250,000 st, 35,000 stpd) are ore. Selection of the optimum shovel and haulage truck fleets will be shown. The principal sources of data for the examples or any other equipment evaluation are equipment manufacturers and actual operations. Whenever possible, actual operating experience should be used to verify estimates. The quantitative data presented herein are unrelated to a specific existing mining operation.

Jan 1, 1979

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons.) Opening for three unmarried draftsmen with large mining company in Chile, S. A. Two must be designers familiar with the layout and detail work connected with a large milling and smelting plant; the third must be good steel designer. Salary starts day of leaving New York; all expenses paid to Chile and return; three-year agreement required. Applicants should state age, experience, and- salary expected. No. 27. ENGINEERS AVAILABLE (Under this heading will be published notes sent to the Secretary. of the Institute by members or other persons introduced by members.) Member, aged 43, with 25 years' experience as engineer, examiner, and superintendent of steel, copper, lead, nickel, gold mines, and plants. Record for organizing and handling work quickly and economically even in remote districts. Last position five years' heavy reconstruction work covering blast furnaces, converters, roasting and refining plant. Ready to go anywhere, similar fields. Speaks German. No. 188.

Jan 3, 1915

September steel production established a new record for a 30-day month with 9,034,000 tons. It was the highest of any month since March. Output of ingots and steel for castings was 535,000 tons more than was poured in August 1952, and 373,000 tons over the total for September 1951. Prime Minister Daniel F. Malan touched a gold button to start South Africa' a first uranium plant into production on the premises of the West Rand Consolidated Gold Mine, near Krugersdorp, Transvaal, 25 miles west of Johannesburg. Uranium oxide is being extracted from mine tailing after removal of the gold. Thirteen gold mines in the region are scheduled for uranium production. Defense Materials Procurement Agency signed an agreement-with the Bagdad Copper Corp., Bagdad. Ariz., for expansion of the firm's facilities to enable delivery of at least 27 million lb of copper a year and 91,0000 lb of molybdenite. It is said that the company will spend about E million on the expansion.

Jan 1, 1952

Assistant Professor of Mining Engineering.-Mining engineer to teach mine surveying, mine mapping, assaying, etc., but not metallurgy. Location, Ohio. Salary, $1800 per annum. No. 379. Metallurgist.-Experienced metallurgist capable of running 25-ton blast lead furnace. Man who knows the country and speaks Spanish desired. You may know that this state is in peaceful conditions and that even during the worst time of the revolution there were several mining concerns never idle. Besides, its resources are wonderful, and once a man gets started, he will find many possibilities. Notwithstanding that Sinaloa is a mining state, our smelter will be the only lead smelter on this coast. Location, Culiscan, Sin., Mexico. No. 381. Quarry Superintendent.-Engineer experienced in limestone quarry work for position as superintendent; must be capable of producing results; must increase output of quarries from 4 to 12 cars per day. Young man with abundant energy is desired. Permanent position, chance to grow up with the company. Location, New Jersey. Salary depends upon the man. No. 382.

Jan 4, 1919

The Institute conducts jointly with the American Society of Civil Engineers, American Society of Mechanical Engineers and American Institute of Electrical Engineers, certain activities as listed below, and is joint owner with them of certain properties. United Engineering Trustees, lnc. When Mr. Carnegie made his gift which made possible a home for the engineering societies, a separate corporation was organized to act as a holding company and to manage the common property. This was long known as the United Engineering Society, but the name has now been changed to one which more nearly reflects the real function of the corporation. It holds title to the Engineering Societies Building and to various funds placed in its charge and is managed by a Board of Trustees, of which three are chosen by each of the four societies, American Institute of Mining and Metallurgical Engineers, American Society of Mechanical Engineers, American Institute of Electrical Engineers and American Society of Civil Engineers, which have equal and undivided interests in. the property. The land and building cost two million dollars. During the year 1934, the Constitution and Bylaws

Jan 1, 1938

By Roger G. Rowe

In late 1980, Exxon Minerals Company performed rock mechanics testing on oriented 150 mm drill core from their 75Fi tonne massive sulfide deposit near Crandon, Wisconsin. Instrumented samples from depths of 300 meters indicate premining horizontal stresses in a north-south direction (parallel to pillar faces) to average 12,300 kPa, with the perpendicular plane yielding an average stress of 14,630 kPa. Rock strength versus sample size was compared using uniaxial compressive strengths from 47 mm, 95 mm and 150 mm core. Massive sulfide averaged 153,300 kPa, 139,845 kPa and 75,330 kPa respectively, while the hanging wall and foot- wall averaged 92,000 kPa, 76,560 kPa and 57,960 kPa respectively. Point load compressive strengths were calculated using formula suggested by both Hassani et al., 1980 and Broch et al., 1972. Values calculated using the Hassani formula closely resembled pre- existing point load and uniaxial compressive strengths, while values calculated using the Broch formula were 50 percent low.

Jan 1, 1982

By AIME AIME

APOCRYPHAL, no doubt, but widely entertained is the proposition that top-flight mining geologists never agree with each other on anything. Being rugged individualists, they frequently seem intolerant of opinions that conflict with their own. However, one may suspect that controversy is often more apparent than real. For example, at last summer's meeting of the American Mining Congress, Ira B. Joralemon and Reno H. Sales, discussing "Mining Geology, Today and Tomorrow," seemed to be in serious disagreement over various phases of the subject; but much of this arises from the different angles of approach of the two distinguished and successful ore finders.

Jan 1, 1941

By B. E. Mix

THE present methods of unloading ore and coarse-crushing at the Magna plant of the Utah Copper Co. are the developments of the past five years. Hand dumping and breaking have given way to the rotary car dump and large gyratory; and the bucket elevators and stationary screens have been replaced by conveyors and shaking screens. The coarse-crushing plant may be broadly divided into two units: the primary crushing and the secondary crushing, or primary roll, unit. The former was erected in 1923; with the exception of the excavation, the construction was carried on by forces of the company. Excavation was started in the middle of March, the first concrete was poured July 16, erection of the steel building started Oct. 30, and the unit was com-pleted and operating Dec. 30. The unit has a capacity of over 24,000 tons of ore per day, and cost more than a million dollars. Remodeling of the primary-roll unit extended over a period of years preceding this, some of the work having been done as early as 1918.

Jan 8, 1925