Search Documents

Jan 1, 1918

By Y. M. Chang, C. H. Pitt

A jet slurry apparatus has been constructed to test corrosive/erosive wear properties of grinding ball metal. Plain high carbon steel heat treated to a hardness of about 60 Rc was used. Slurries of quartz and chalcopyrite ore concentrate were used as the jetting media. Weight loss due to pure corrosion was determined by the linear polarization technique. Weight loss due to pure erosion was determined by jetting while cathodically protecting the sample. By comparing the total weight loss with the sum of the weight losses from pure corrosion and pure erosion, it was found that there was a synergistic effect between corrosion and erosive wear. Corrosion rate, erosion rate, and total erosion/corrosion rate are given as a function of pH and mineral type.

Jan 1, 1986

Jan 12, 1951

By Kingman, Robert I.

SUFFICIENT testing has been .performed with the Dutch State Mines Cyclone for thickening and desliming flotation feed at the concentrator of the National Lead Co., Tahawus, N. Y., to prove its application for this work. It is the purpose of this article to present some of the test results, operational details and advantages of cyclone thickening and classification. The metallurgy of the mill operation was described by Frank R. Milliken, assistant manager of the titanium division.

Jan 1, 1950

By J. E. McConnell

No. 1 Electric Furnace and Billet Casting Shop, located in Plant No. 4 adjacent to our new 12 inch merchant bar mill, represents Inland Steel Company's first venture into both electric furnace steelmaking and continuous casting. Construction of the shop began in September, 1968 with excavation and foundation work, followed by awarding of general construction and major equipment contracts from December, 1968 to April, 1969. The first heat was tapped from No. 90 furnace on December 18, 1970, and the first cast attempted on December 29, 1970. The rated shop capacity is 500,000 tons per year of semi-finished billets and blooms, and was justified on the basis of approximately 85 percent of the product mix falling into the special bar quality category of steel grades. Auxiliary equipment has been designed into the shop to pursue free machining steels, including leaded and tellurized grades. The start-up and operation of the shop for the first year was essentially based on a two-part philosophy: 1. Initially operate with the "open stream" casting technique to accomplish machine shakedown and operator familiarization and training. 2. Operate with special bar quality, or "submerged casting", practices, make necessary refinements and gain customer acceptance

Jan 1, 1972

By Charles H. Jones

Jan 1, 1905

By Booker Morey, Ashok Gupta

Amid controversy, the resource recovery industry is rapidly approaching its first commercial operations. Some of the problems are reviewed along with some of the important systems that are being developed for resource recovery. Market specifications for the inorganic fraction recovered from municipal solid waste are reviewed along with the details of the unit operations that have been tested.

Jan 1, 1976

By J. C. Konopka, S. A. G. Poppen, E. K. Roesner

Many shafts have experienced stability problems during shaft sinking because the designer failed to fully appreciate the conditions he would encounter. Some shafts have failed during construction because the ground supports provided to compensate for the expected conditions were inadequate despite the most careful investigations and analyses. To design a ground support which is ultimately safe to achieve stability during shaft sinking would be too costly and impractical and, therefore, many shafts would simply not be constructed. The design of a ground support for shaft sinking based on an intimate understanding of the expected ground behaviour and stress development during excavation combines the art of mining with the science of geotechnical engineering. Where no historical design data is available, the designer of the ground support must: 1. classify the rocks and soils and assess their behavioural characteristics; 2. calculate the primary and secondary stresses; 3. design and/or select a ground support system which will ensure stability of the excavation during shaft sinking.

Jan 1, 1983

By James M. Barker

Jan 1, 1985

Jan 1, 1920

By JAMES J. PURDY

The great majority of stokers used in residential heating installations are of the clinkering type. Because of inherent characteristics of the under- feed combustion process as it occurs in these small stokers, and because of the wide range of operating conditions encountered in residential heating schedules, not all bituminous coals can be used successfully in residential underfeed units. The problem of providing consumer satisfaction has been attacked by the joint efforts of the stoker manufacturers and the coal industry; the stoker manufacturers have been concerned with improving their product to permit the use of a wider range of coals, and coal operators have made every effort to market selected and better prepared coals. In view of the wide range of physical characteristics and chemical properties of bituminous coals, the problems are real and are receiving increased attention.

Jan 1, 1949

Abel, Charles Edwin, Student, Univ. of California Los Angeles, Cal. '31 Adams, Horace M.5148 Benton Ave., Downers Grove, Ill. '31 Ahlskog, Harold A., Student, Washington State College Pullman, Wash. '30 Aldridge, John, Student, New Mexico School of Mines Sbcorro,, N. M. '30 Allen, Hugo K., The Univ. of Texas 104 W. 33rd St., Austin, Tex. '31 Ames, Marshall B., Student, Washington State College Pullman, Wash. '31 Ancell, Virgil F., Student,. Missouri School of Mines Rolla, Mo. '30 Anderson, Norman John, Student, South Dakota School of Mines Rapid City, S. D. '32 Annett, Norman T., Student, Mackay School of Mines, Univ. of Nevad Reno, Nev. '32 Apablasa, Salvador C., Student, Univ. of California Los Angeles, Cal. '31 Armstrong, James Arthur, Jr., Student, Michigan College of Min. & Tech., Houghton, Mich. '31 Armstrong, John R. Box 274, Neosho, Mo. '31 Armstrong, Robert H., Student, Lafayette College Easton, Pa. '31 Armstrong, Thomas E., Student, Univ. of California Los Angeles, Cal. '31 Arnot,. Paul H 2617 Haste St., Berkeley, Cal. '31 Ashby: Harve I., Willow Creek Mines Wasilla, Alaska. '31 Aud, Robert A., Student, Lafayette College Easton, Pa. '30 Augenthaler, Robert L., Student, New Mexico School of Mines Socorro, N. M. '32 Augustine, Grant, Jr., Instrument man, Min. Dept., Fairbanks Exploration Co., Fairbanks, Alaska. '31

Jan 1, 1932

Jan 1, 1887

By V. F. STANLEY

THERE is not the slightest doubt that the present recoveries of valuable minerals by the Broken Hill mills could be improved, and that further machinery would be installed for the purpose if it could be assured that a high price of metals would be maintained; but concentration, like all other com¬mercial propositions, is a question of profit and loss, and no sensible metallurgist would carry out his work in such a manner as to obtain high recoveries at a financial loss to his company. There is a point in all concentration at which the added money obtained from the higher recovery of minerals is balanced by the extra cost of obtaining the last part of the recovery; a wise metallurgist will be content with his work before his working-expenditure reaches this point. To a casual observer, the work being done by the various Broken Hill mills is identically the same. A closer investigation will show that this is far from being the case, for it is a remarkable fact that, although the larger mines extend over a length of approximately only 2 miles, such a difference in the physical and chemical properties of the ores exists that, from the first reduction downwards, special treatment is necessary in each case, and hardly any two mills are identical in operation. The details of this paper refer directly- to the work of one . particular mill in Broken Hill, for the reason that the ore from each mine presents special difficulties and requires its own special treatment. I have selected the mill referred to because it has been constructed and modified under my supervision.

Sep 1, 1909

By August E. Vandale

Mining of the Freeport and Pittsburgh coal seams in the Pittsburgh vicinity dates back more than 100 years, and Consolidation Coal Co., or its predecessor, Pittsburgh Coal Co., has been actively mining in the area since 1900. Over the years, Consol has acquired good legal title to the coal lands purchased from individual farm owners, with broad mining rights, and in 98% or more of its title holdings, the company has a complete waiver of surface damage or the right to subside the surface land. (Titles in Pennsylvania can be in three forms: title in fee; title to the mineral; or mining rights permitting the removal and extraction of the mineral with or without waiver of surface damage.) In the early history of Consol, individual farms overlying the seams were purchased from land owners. Many of these titles severed the coal estate from the "in fee" title, and mining rights with waiver of surface damage were conveyed in the original severance deed. In this manner, Consol was able to put together its large mineable coal reserves. Consol has practiced "full recovery" mining as far as practical from its early years of hand loading to the recent era of mechanization.

Jan 9, 1967

TO THE BOARD OF DIRECTORS, AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS: Gentlemen.-I have the honor to present the following report of the President for the year 1919. In order that this report may be printed and distributed to the members in advance of the February meeting, it is necessary that it end with the calendar year 1919. Any activities during the first six weeks of 1920 will be covered in the Secretary's report for the year 1920. VISITS TO MEMBERS Your President has visited each of the Local Sections of the Institute, with the exception of the ones at Washington, D. C., Tulsa, Okla., and the Nevada Section. These three sections have not arranged meetings at which the President could be present. In addition, your President, accompanied by President Jennings and Secretary Stoughton, in the year 1918, attended meetings of members in Minneapolis and Duluth, Minn., and Houghton, Mich. A dinner and meeting of the members in Pitts-burgh, Pa., was also attended, in company with the Secretary and your President also attended the meeting of Canadian Mining Institute in Montreal, in March, 1919.

Jan 2, 1920

By BLAllEY STEVENS

(Canal Zone Meeting, November, 1910.) I. INTRODUCTION. TEH object of this paper is to show how igneous intrusion is governed by definite mechanical laws. A distinction is made between dikes and fissures, and the various characteristics of intrusions are explained on an exact scientific basis. The modification of rock-stresses by intrusion is then considered and extensive isostress regions are recognized. Finally, a complete classification of intrusions is constructed covering all pos-sible cases. The generalizations of observed data, taken from Geikie's Textbook of Geology, conform to the laws of intrusion herein stated, and the deductions based upon these laws. No authority, however, is quoted for the type which I have named a corrugated intrusion. Its existence is a necessary deduction from the laws of intrusion, and even the entire absence of examples in technical publications cannot disprove its reality. In all probability, corrugated fissures would have remained undiscovered, but for the working of mineral veins. As intrusions of tabular form are seldom worked for commercial purposes, it has been left for theory to anticipate the discovery of corrugated dikes. In the light of these laws of intrusion and the corresponding laws of fissures,1 there seems to be a remarkable uniformity of stress-distribution in rocks at moderate depths. This renders .possible the mathematical calculation which should help us to approximate exact science in this and kindred branches of applied geology.

Jan 1, 1911

By R. S. Dean

REQUIREMENTS for war materials have led to large scale experimentation upon metallurgical innovations. It is of interest to inquire what this may contribute of permanent value to our existing technology, as innovations adopted during war are apt to be discarded promptly at its end. This is because utilization of substandard ores usually requires a new technology for ore treatment, and a new use-pattern for employment of the products. Thus two very different problems are involved: first, devising a process; then, adopting its products by industry, with readjustments of the use-pattern if necessary. A new process may be as good or better than an old one, but the readjustments required for use of its products may prevent its general adoption if this implies scrapping existing plants and investing much additional capital. Metallurgical innovations are of three kinds: I. The use of substandard material in processes already established; 2. The grading-up of substandard material to render it more suitable for established processes; 3. The adjustment of technology and use-pattern to the raw materials that we have.

Jan 1, 1945

Jan 1, 1884

Jan 1, 1897