Search Documents

By T. S. Fuller

The tensile properties of steels at elevated temperatures have been studied by numerous investigatorsll primarily for the purpose of determining their suitability for structural uses. Tests with this objective have been confined largely to the temperature range of approximately 20" to 500' C., because of the rapidly decreasing tensile strength at the latter temperature. Tests have also been extended to higher temperatures2 for the purpose of determining the most suitable forging range. This temperature range is also of theoretical interest. The phenomenon if increased tensile strength and decreased ductility .in the so-called "blue-heat" range, approximately 200" to 300" C., is well known. It was suggested to the Bureau early in 1926 that a study of the properties of rail steels in this temperature range might prove of interest in relation to the studies of transverse-fissure failures in rails. There were available from another investigation3 several new rails from several different heats made to approximately the same specification requirements, the complete manufacturing histories of which were known. It was decided to determine, at least in the preliminary series of tests, only the ultimate tensile strength, elongation and reduction of area, because of the difficulty, time and cost involved in determining the proportional limit and yield point at elevated temperatures.

Jan 1, 1930

By Hisahiro Kinoshita, Derek Temple, Yoshio Higashitsuji

The zinc-lead blast furnace process has been installed by two smelters in Japan. In 1966 a unit was commissioned at Harima in Hyogo prefecture by Sumitomo Metal Mining Co. Ltd. and in 1969 a consortium of other Japanese zinc and lead smelters completed their unit at Hachinohe in Aomori prefecture, managed by Mitsui Mining & Smelting Go. Ltd. , the major shareholders. The special characteristics of these two plants are described with particular emphasis on their location and operation. Reference is also made to the processing of a wide range of raw materials, including residues from other processes. Both plants pay scrupulous attention to plant and environmental hygiene to meet the high standards set by the local prefectural governments; the ways in which this has been achieved are discussed. General performance data on each furnace is included, showing that this pyrometallurgical process is supplying 16% of Japan's zinc and refined lead consumption. Note - All tonnes (t) are metric of 2204 lbs.

Jan 1, 1976

By Anna H. Connard

SUMMARY The discussion focusses on developments in the debt/equity swap market since the Marte project was negotiated in early 1988. It emphasises carrying forward the recent market trends to anticipate the breadth and scope of debt/equity conversions for mine development in the 1990s. Secondary market prices of LDC paper, conversion values and political influences in the host countries and the use of near debt and commodity-based instruments as components of mine financing in debt/equity deals will be placed in the perspective of recent trends and expectations for the future. THE MARTE PROJECT The Marte mine is a gold porphyry deposit in Chile's high Atacama, for which financing was put together at the beginning of 1988. The Marte project was financed by a combination of common equity and loans. It was unusual that the equity infusions were made under different programs. Some of the international equity was infused with fresh funds via DL 600. Other common foreign equity was provided through the conversion of Chilean bank debt under Chapter XIX. On the loan side,. export credits for the import component of machinery and equipment were sought. Local bank financing was negotiated for the remainder of ' the project's anticipated cost. The debt conversion market in Chile was at its apex in terms of interest, activity and government support when the mine financing was arranged. The price of Chilean paper in the secondary market hovered about 62 to 66 cents per U.S. dollar of face value. Meanwhile, the Chilean government was negotiating conversion redemptions significantly closer to full face value. The government differentiated between debt paper exchanged for corporate investors who had sourced that paper in the secondary market, and debt paper held by bank investors who would incur a transaction loss in the conversion. The use of a combined DL 600lChapter XIX equity financing created different yield calculation bases for the various investors. Chapter XIX prevents remittance of profits before year 5 and capital repatriation before year 11. Investors choosing this vehicle have either for a corporate policy in the target project not to declare dividends until repatriation is allowed, or they have to seek uses for the peso liquidity that would be generated through dividend declarations in the early years. However, DL 600 investors face no such waiting period on dividends, nor do they have restrictions imposed on cashing out of the investment before the 11th year. Therefore, any equity structure with components of both investment mechanisms will have inherent differences in cost basis and future income flows for the various participants. This equity imbalance is defensible if the investment motivations of the parties are analyzed: a mining investor using fresh funds looks for a hurdle return on equity calculated at conservative commodity prices, with as much flexibility to reap upside benefits as possible; a mining investor choosing to invest through a debt conversion mechanism will realize a modest short term gain on the conversion, reducing his effective cost basis, but sacrificing some return because of the waiting period on repatriation of dividends. INVESTMENT OBJECTIVES A bank investor exchanging his own paper for an equity participation in a mining project realizes a conversion loss on the transaction. He seeks a risk adjusted acceptable hurdle rate of return to recoup that loss over time. Motivation for the bank investor to take that loss may be derived partly from a strategy to diversify its existing portfolio by internal policy and externally regulated guidelines. The bank will compare yields on its loan portfolio to that country with anticipated dividend flows discounted back at a risk adjusted rate. It will analyze the project with return objectives of yield enhancement over time and with

Jan 1, 1990

By J. H. O’Dette

BLISTER formation on wrought aluminum products has been a matter of concern to aluminum fabricators for many years. The fact that blisters make their appearance during the final stages of fabrication means that much time and effort have been expended before it is evident that the material must be scrapped. This and the loss of production are ample reasons for embarking on a research program to find out more about blistering and possible methods of control. Many excellent papers on this subject have appeared in the technical literature in the last few years. In one of the more recent papers, Kostronl gives a fairly complete review of the problem of gas in aluminum and blistering in general. From the work of the various investigators, a general mechanism for the formation of blisters has evolved and may be summarized briefly as follows: Hydrogen gas is usually present in the cast ingot, in the atomic or ionic state, in excess of the solid solubility. At room temperature the gas atoms are relatively immobile, but at elevated temperatures they become mobile and diffuse to free surfaces where they associate to form molecules. If these free surfaces are discontinuities within the ingot then the associated gas molecules collect and build up considerable pressure until equilibrium is reached with the dissolved gas around the discontinuity. Since the solubility of the gas is proportional to the square root of the partial pressure it is evident that large pressures may be built up at the discontinuities. When the metal is rolled to sheet the pressure of the gas in these, discontinuities is sufficient to deform the surface of the sheet and form a blister, particularly when the strength of the material is reduced during the annealing. Although the mechanism of the formation of blisters was fairly well known, the actual impor- tance of the individual roles played by the gas and the discontinuities was not so well established that positive methods for control of blistering were at hand. It was the object of the investigation to learn more about the nature of the discontinuities giving rise to blistering and to develop methods of control. The investigation was carried out in three stages as follows: a) A study of the more commonly used methods of removing hydrogen from aluminum, such as fluxing and holding, and their effects on blistering. b) Location of the discontinuities giving rise to blistering. c) A study, by indirect methods, of the movement of gas in the metal and its effect on blistering, and the development of methods of blister control during fabrication. Removing Gas and Reducing Blistering by Fluxing or Holding-—The work of removing gas and reducing blistering by fluxing or holding was carried out on metal of Alcan 2s (1100) composition with an artificially high gas content. The high gas content was obtained by introducing water into the melt prior to casting; the water reacted with the aluminum forming A12O3 and hydrogen. The procedure was to raise the gas content by introducing water into an aluminum melt and using half the melt to cast one ingot immediately. The remaining metal was treated again with water to make up for the reduction in gas content during holding, while the first ingot was being cast, and then given a fluxing or holding treatment and cast into an ingot. Samples for gas determination were cast from the molten metal before and after the gassing operation; before, after, and during fluxing, and while casting. Samples were also cut from sections of the ingots. Gas determinations were made on these samples using the well known vacuum fusion technique. All ingots were hot rolled at 500°C to 0.250-in. slab which, in turn, was cold rolled to 0.040 in. sheet. The sheet was coiled and annealed for 2 hr at 500 °C and then cut into 5-in. squares which were inspected for

Jan 1, 1958

By M. G. Corson

Information regarding the use of ixanganese alloys has hitherto been incomplete and available only from widely scattered sources. This paper attempts a systematic description of properties and uses of alloys other than manganese bronze, manganin and duralumin, which are probably the only non-ferrous alloys associated with manganese in the minds of most metallurgists. Properties of Manganese Manganese can react either acid or basic; it is hard to obtain in the pure state; it has two different crystalline lattice structures, both of the cubic system, one stable above 850" C. and the other below 650" C., both coexisting in the intermediate range. Although the commercial product is hard and brittle, the pure metal seems to be ductile. In fact Zhemchuzhny, in Russia, was able to obtain ductile manganese and draw it to fine wires by the simple expedient of adding about 3 per cent. copper to the alumino-thermic product. Copper most probably brings the sili-cides, aluminides, nitrides and carbides present in the commercial product into a much less harmful form of distribution. One industrial use that can be foreseen for wrought manganese articles is as anodes for electrolytic processes in sulfate and nitrate solutions, particularly with high voltages. A practically insoluble skin of manganese peroxide is likely to form in such cases and an insoluble and strong anode material will be available. Manganese as a Scavengek Because of its activity manganese might become the most efficient scavenger and refiner of copper, were it not for the fact that 0.01 per cent.

By P. Martignan

UNTIL quite recently, Alsace was the only district in France where petroleum could be found in somewhat industrial quantities. The Pechelbronn fields produce, however, only about 80,000 tons a year, which represent approximately one-eighth of the domestic consumption. Much research work has been done in Alsace to find the prolongation of the Pechelbronn fields, but instead of oil the drillings revealed the existence of large deposits of potash. This can, be easily explained when one remembers that the Pechelbronn oil is of the Oligocene period, and, that in the Alsatian stratification the Oligocene lies immediately on the Keuper, i. e., on the strata that originate from a period during which the largest salt and potash deposits were constituted. Before the war, and mostly at the end of the last century, some wells were drilled in various districts of France where some analogies could be found with the Alsatian geology, the borings being mainly made in the Triassic and Tertiary beds. They led to negative results. After the war, the growing importance of oil urged the necessity of resuming the explorations. But it is our belief. that this was greatly facilitated by the enacting of new legislation, which is embodied in the Mine Act of May 16, 1922.

Jan 3, 1925

By T. L. Joseph

IN connection with its investigations of the blast'-furnace process, the Bureau of Mines, in coöperation with the Minnesota School of Mines Experiment Station, developed a 6-ton experimental furnace. Such a furnace was needed to determine the feasibility of producing ferromanganese from Minnesota manganiferous iron ores, a problem of national importance because of the present need for manganese in the steel industry and our small reserves of ferro-grade ores. Furnace operators are reluctant to use new or untried raw materials or to make decided innovations in practice on account of the financial hazard of experimenting with full-scale equipment. A small furnace which can be operated at a relatively low cost is particularly adapted for testing new, raw materials and for determining the feasibility of decided innovations in practice. Laboratory experiments, plus whatever information may be available, are valuable but often do not indicate the net result of changes in an operation involving a large number of interrelated variables. From time to time the coöperation of the Bureau of Mines is solicited in connection with problems involving departures from normal procedure. Under these circumstances some sort of a practical demonstration is a desirable forerunner to full-scale operations which appear feasible after small-scale tests.

Jan 1, 1928

By C. E. Tsoutrelis

A new method for determining rock drillability in diamond drilling is discussed; the method takes into consideration both penetration rate and bit wear. The method is based on drilling a rock specimen under controlled laboratory conditions using a model bit. The technique used for determining the experimental variables is extremely simple, quick, and reliable. Drillability is then determined by the mathematics of drilling. In considering the different factors that affect diamond drilling performance, the nature of the rock to be drilled is of outmost importance since it affects significantly the drilling costs and such other variables as bit type and design, drilling thrust, and bit rotary speed. Many attempts have been made to study this effect by correlating actual drilling performances either to certain physical properties of the rock being drilled1-? or to test drilling data obtained under laboratory conditions.7-13 These attempts were aimed at providing a reliable method of predicting by simple means the expected rock behavior in actual drilling, thus giving the engineer a tool to use in estimating drilling performances and costs in different types of rock. The purpose of this paper is to describe such a method by which rock drillability (a term used in the technical literature to describe rock behavior in drilling) could be determined in diamond drilling. It is believed that the proposed simple and reliable method will cover the need of the mining industry for a workable method of measuring the drillability of rocks. It should be emphasized, however, that since drill-ability depends on the physical properties of rock and each drilling process (diamond, percussive, rotary) is affected by different or partly different rock properties,14-l6 the proposed method of determining rock drillability cannot be extended to the other drilling processes. The results presented in this paper form part of an extensive three-year research program carried out by the author in the laboratories of the Greek Institute of Geology and Subsurface Research. During this period the effects of the physical properties of rocks and of such operational variables as drilling thrust and bit rotary speed in diamond drilling were investigated in detail. DRILLABILITY CONCEPT The literature is not devoid of drillability studies. While there are a number of investigators1,3,5-7,9-0,12-13,17 who have attempted to establish by direct methods (i.e., drilling tests under laboratory conditions) or indirect (i.e., through a physical property of rock) an index from which the drilling performance in a given rock may be estimated, very few6-7,9,12, of the proposed methods seem to be of much practical value to the diamond drilling engineer and none to date has been universally accepted. Commenting on the proposed methods for assessing rock drillability, Fish14 remarks that "for a measure of drillability to be accepted it is essential that penetration rate at a given thrust and bit life are elucidated as otherwise the method is of little value." This statement should be examined in more detail by making use of the penetration rate-drilling time diagram obtained in drilling a rock under constant operational conditions. Furthermore, the merits of using this diagram to describe rock drillability will be pointed out. At the same time reference will be made to this diagram when discussing some previously proposed methods. Fig. 1 illustrates such a diagram for three rocks,A, B, and C, which have been diamond drilled under identical conditions. It is assumed here that rocks A and B have the same initial penetration rate, i.e., VOA = Vog, but since rock B is more abrasive than A, rapid bit wear occurs and as a result the fall of its penetration rate with respect to time is more vigorous than in rock A. This is shown graphically by a steeper V = f(t) (0 curve in this rock than in rock A. Rock C has a lower initial penetration rate, due to higher strength properties16 but since it is not very abrasive, only a slight fall of its penetration rate occurs during drilling (in this category are some limestone and marbles with compressive strength above 1000 kg per sq cm). It follows from the foregoing considerations that the characteristic for each rock curve (I) is a function of (i), the penetration rate of the rock Vo recorded at the instant of commencing drilling, which determines the starting point of the curve (1) on the y-axis and (ii), the abrasive rock properties which determine the rate of fall of Vo with respect to time. Thus, curve (I) provides an actual picture of the rock behavior in drilling for given operational conditions, and it can be used with complete satisfaction to assess rock drillability. It can be seen clearly from Fig. I that proposed methods for assessing rock drillability by measuring the

Jan 1, 1970

By James H. Hance

Discussion of the paper of JAMES H. HANCE, presented at the New York meeting, .February, 1916, and printed in Bulletin No. 110, February, 1916, pp. 299 to 326. FREDERIC P. DEWEY, Washington, D. C. (communication to the Secretary*).-I wish to congratulate Professor Hance and to thank him for his extremely valuable addition to the fund of data upon this subject. It presents clearly conclusive and incontrovertible proof of the unreliability of drill samples of this class of metal for determining the value of such bullion. I am afraid, however, that his hope that some one in the mint service might continue such an investigation upon a more elaborate and exhaustive scale is, for the present at least, doomed to disappointment. As a practical matter, the mint service is not now particularly interested in segregation in crude bullion. So much trouble and friction arose, -both in the original purchase and in the transfer from one institution to another, in handling segregated bullion, that it became necessary to adopt drastic measures and now it is seldom attempted to determine the value of such bullion in the service. When bullion known or even suspected of being segregated is presented for purchase, it is at once strongly refined in the pot and the disturbing elements so far removed that concordant assays may certainly be obtained from the dip samples and a reasonably fair agreement obtained from drill samples. The mint service prefers that the owner should refine his bullion himself, but if he does not we will do it at his expense and return the slag to him when desired. Much work has been done in the mint service trying to arrive at the value of deposits of segregated bullion without strong refining. It was no unusual thing for such deposits to be melted three times at the purchasing office and to have 30 to 40 assays on the metal made before buying it. Yet when shipped to a mint it was found necessary to melt two or three times more and to make 15 to 25 assays before the mint would accept the bar, and there were considerable differences between the valuations of the two offices. In what was undoubtedly the worst case ever investigated, the purchasing office melted the deposit, 953 oz., three times, with a loss of 105.5 oz., and made 46 assays; the mint melted three times, with a loss of 6.6 oz., and made 28 assays. The mint allowed the purchasing office 1.178 oz. of fine gold more than the purchasing office claimed, while an extensive investigation of the mint samples by the Bureau, in which over 100 independent assays were made in various service laboratories, indicated that the metal carried 0.7 to 0.9 oz. more of fine gold than the mint allowed. Preliminary assays on the original metal

Jan 5, 1916

By Madan M. Singh, William J. Courtney

Pneumatic stowing is commonly employed in European coal mines, but is not used in the United States. This paper reports a study conducted to analyze the conditions under which pneumatic stowing might be advantageously used and the techniques and costs involved in order to effect this. Although stowing may reduce the subsidence in a mining area, this does not entirely eliminate the surface damage. Besides, the cost of stowing will run about $1.50 to $3 per ton of coal mined not including the cost of fill material, if it has to be bought and transported to the mine. Stowing my, however, be economically viable under special circumstances such as in thick, steep, or contiguous seams.

Jan 1, 1976

By S. P. Sharples

HAVING occasion a few weeks ago to investigate the subject of black band iron ore in West Virginia, I was surprised at being met at the outset with a denial of its existence. One gentleman went so far as to offer one hundred dollars an acre for any land in West Virginia that contained a seam or vein of even a single foot in thickness, and when shown the ore he acknowledged that it was genuine, but declared it had been imported. That black band does occur in West Virginia is to-day well known to a number of persons. There is a seam on the Gauley River of about a foot in thickness of good ore, which I understand Mr. Lewis and others are making preparations to work. The great trouble with black band ores as heretofore found in this country has been their limited extent. At Fort Washington, for instance, they had a very fine show ing of ore, but it soon gave out. It has also been asserted that the black band ores of the Western Coal Measures were worthless in the furnace, and Fort Washington has been pointed out as an example of the fate of any one who should undertake to work them. But they have been successfully worked at Youngstown and in other parts of Ohio, and I am assured by old furnace-men from Ohio that there is not the slightest difficulty it working them if properly managed. The deposits to which I wish to call the attention of the Institute,

Jan 1, 1882

By Frank W. Harris

THE strength of hard drawn copper wire is a question of considerable importance to both manufacturer and consumer. Unlike steel and alloy wires, in which strength is governed by both chemical and physical considerations, the high conductivity required for copper wire in the electrical industry generally precludes the possibility of obtaining tensile strength through the use of alloys. Consequently, this strength is largely a matter of the physical structure, and all factors known to affect this structure, such as rolling temperature, die contours, lubricants, drawing speeds, etc., are matters of prime importance. The experiments described here have been carried out during the past year at the Baltimore plant of the American Smelting & Refining Co., in connection with a general investigation of some of the questions mentioned above, with the object of studying the physical structure of hard drawn copper wire and the influence of certain factors on that structure. The work has been of an exploratory nature, rather than comprehensive, but it was thought that the results might prove of sufficient general interest to warrant their publication. The bulk of the hard drawn copper wire used in places where strength is an important factor is manufactured to strict specification, based usually in the United States on that of the American Society for Testing Materials (B-1-23). This specification calls for almost as high a value of tensile strength, consistent with elongation, as it is possible practically to obtain, and only physically perfect material can be relied on to meet such a specification. Obvious defects, such as laminations produced through fins in the original rods or brittleness due to overdrawing, are usually recognized and need only passing reference. Laminations can be detected by twisting and untwisting the wire several times; they will show up on the surface in the form of fins. Fig. 1 shows a very bad example of this defect. The wire may be perfectly smooth before twisting but when such laminations are present they will readily show up under this treatment. This trouble is caused by similar defects in the original rod produced by overfills in rolling. Fig. 2 shows the cross-section of the rod from which the wire in Fig. 1 was drawn.

Jan 1, 1928

By D. S. Bloom

RECENTLY a report has been published on an investigation of the MO-RU system by E. Raub.' In this report it is stated that below approximately 1200°C the system consists of two terminal solid-solution phases and the intervening two-phase field; at 1200°C and above, an intermetallic compound labeled Mo,Ru, makes an appearance. Along with some other little known systems in which it was considered possible for a u phase to form, the Mo-Ru system had been under investigation in this laboratory. Since molybdenum and ruthenium have very high melting points and also since ruthenium is expensive, the investigation was confined to X-ray diffraction by sintered powder compacts. The compositions which were studied were (in atomic percentages): 75 Mo-25 Ru, 67 Mo-33 Ru, 50 Mo-50 Ru, and 25 Mo-75 Ru. All compacts were made from the pure powders, and no chemical analyses were attempted. Each compact weighed about 5 g. All annealing was done in evacuated Vycor capsules, and even though the capsules completely collapsed at 1250°C, they still admitted no air. The results of this investigation in general corroborate the work of Raub. Up to 1150°C the two terminal solutions and the intervening two-phase field were found, and at 1200°C and above an intermetallic compound was found. However, the composition limits of the compound were estimated to lie close to 70 atomic pct Mo rather than 62.5 atomic pct Mo as Raub had reported. At least the X-ray diffraction results indicated that the 75 atomic pct Mo specimen consisted of the molybdenum solid solution plus the compound, while the 67 atomic pct Mo specimen consisted of the ruthenium solid solution plus the compound and the equiatomic composition contained only very little of the compound. The most interesting observation, however, was that the diffraction pattern of the compound was similar to that of the well known u phases, except that unusually large lattice constants were indicated. The d-values, or interplanar spacings, of the diffraction lines (as produced by filtered copper KCX radiation) of the compound are given in Table I, as determined from specimens annealed at 1250°C for 9 hr and then quenched in water. Also shown are the lines of the Mn-Mo u phase as given by Decker, Waterstrat, and Kasper,' the lines of the Fe-Mo a as given by Goldschmidt," and the lines of the Mo-Ru phase multiplied by constants in order to make comparison with the Mn-Mo and Fe-Mo patterns easier. These results indicate that the compound in the Mo-Ru system is apparently isomorphous with the other o- compounds. The rather large lattice constants of the Mo-Ru a phase are acceptable in view of the comparatively large size of the constituent atoms. The data in Table I for the Mo-Ru compound check quite well with those given by Raub, not shown here, though there are some discrepancies between the two sets of data in the estimated intensities of a few lines. Although very little is known at present about this u phase, there are some things which may be pointed out, mainly in comparison with other better known u phases. Even though molybdenum and ruthenium are in the same columns in the Table of Elements as chromium and iron, respectively, the Mo-Ru u phase contains much more molybdenum than ruthenium, while the Cr-Fe u phase centers around or very nearly around the equiatomic composition; furthermore, the Mo-Ru u is stable only above approximately 1200°C, but the Cr-Fe u is stable only below about 825 °C. With respect to its being unstable below 1200°C, the Mo-Ru u is similar to the other binary molybdenum u phases in the Co-Mo and Fe-Mo systems. Similar to the latter two systems, the Mo-Ru u apparently exists over a rather narrow composition range, whereas the Cr-Fe u at lower temperatures is stable over a much wider composition range. The Mo-Ru u thus is closer to the other molybdenum u phases than to the Cr-Fe cr phase. The most striking feature of the Mo-Ru u phase, however, is the absence of any of the transition elements of the First Long Period.

Jan 1, 1956

By C. J. McHargue, J. C. Ogle

Lightly deformed columbiun single crystals which contained only parallel hoins or purullel and intersecting trains were annealed at 1000' and 1600"C. No re-crystallizntion occurred in specimens hawing only parallel twins. Only noncoherent twin boundaries nzipated at 1000°C but both coherent and noncoherent ones moved al 1600°C. Recrystallization occurred within a few minutes at twin intersections at 1000°C. The orientation 01 the recrystallized grains differed front that of both the matrix and deformation twins, but could he derired by (110) and/or(112) rotations. ALTHOUGH twinning in metals has been extensively studied, there have been no definitive studies of the annealing behavior of crystals containing deformation twins. Some effects observed after annealing deformation twins have been summarized by Cahn1 and Hall2. Any or all of these phenomena are observed: 1) The twins may contract so that the sharp edges of the lens become blunted, and eventually the twin may disappear entirely. 2) The twins may balloon out at an edge, giving rise to a large grain having the same orientation as the twin. 3) The specimen may recrystallize; i.e., new grains are nucleated and grow at the expense of the twins and the crystal immediately adjoining the twin. Such grains have orientations which are not present before. Contraction has been observed in iron,3 titanium,3, 4 beryllium,5 zinc,8, 7 Fe-A1 alloy,' and uranium.9 Long anneals at high temperatures are required to have any appreciable effect in these metals and only thin twins are absorbed. Lens-shaped twins are absorbed from the edges: the thin, almost parallel-sided twins are usually punctured in several places and each piece contracts independently. Absorption is very gradual and no sudden cooperative jumps have been observed. The expansion of a twin into a larger grain of identical orientation is unusual, but such growth has been observed in iron,"'" zinc,6 and uranium." Crystals which have been deformed simultaneously by slip and twinning recrystallize first in the area adjacent to the twin. New grains appear faster where the twins intersect: but isolated twins, especially if thick, can also give rise to new grains. This type of recrystallization occurs in zinc.6, 7, 12, 13 and beryllium.14 Reed-Hill noted, in a single crystal of magnesium, the nucleation of a recrystallized grain at a twin intersection which had the same orientation as the second-order twin and which grew into the highly strained matrix.15 Short-time annealing has been reported to cause no change in the deformation twins in vanadium,16 columbium, 17, 18 tantalum,19 tungsten,'' and zinc.7 The purpose of this investigation was to note the effects of annealing on the coherent and noncoherent boundaries of deformation twins in columbium and to locate the nucleating sites for recrystallization. The orientation relationships, which the new recrystallized grains have with the parent crystal and the deformation twins, were also determined. EXPERIMENTAL PROCEDURE Single crystals of columbium were obtained by cutting large grains from electron-beam-melted buttons which contained 10 to 50 ppm C, 10 to 100 ppm O,, 1 to 10 ppm H2, and 10 to 15 ppm N2. The crystals were hand-ground and chemically polished until all grain boundaries were removed. The specimens were mounted in an epoxy resin and a face of each crystal was mechanically polished on a Syntron polisher using Linde A and then Linde B polishing compounds. After all faces were mechanically polished, the crystal was electrolytically polished to remove all distortion due to cutting and grinding. Laue photographs were taken of all faces of the crystals to determine the quality and orientation of each crystal. The crystals were compressed about 10 pct at -196 C in a specially constructed compression cage with an Instron tensile machine. Each crystal was separated from the top and bottom anvils by teflon films which acted as a lubricant. With the specimen crystal in position, the entire cage was cooled to -196°C by being submerged in a Dewar containing liquid nitrogen. The crystals were compressed at a rate of 0.02 in. per min and the load was recorded on a strip-chart recorder. After deformation the crystals were mechanically polished on 600-grit paper and Pellon cloth with Linde A and Linde B polishing compounds. The crystal faces were chemically polished and then etched. The twin planes were identified metallographically from an analysis of the twin traces on two surfaces. Annealing was carried out by placing each crystal in a columbium bucket made from the same electron-beam-melted material as the crystal itself and suspending the bucket by a tantalum wire in a quartz tube. After a vacuum of 10-7 Torr was attained, a furnace at 1000" or 1600 C was raised into position and the crystals held for various lengths of time. The crystals were repolished and etched after annealing to remove any surface contamination. Approximately 0.010 in. was removed during this process. The resulting surface was examined metallographically for microstructural changes due to annealing. A microbeam Laue camera mounted on a Hilger Micro-focus X-ray unit was used to determine the Orientstions of the recrystallized grains. This X-ray micro-beam camera had a 0.002-in.-diam collimator and incorporated the ideas of both and and chisWik21 and Cahn.22

Jan 1, 1967

By O&apos, P. E. T. Connor

Production of petroleum in Trinidad during 1938 reached the record figure of 17,737,061 bbl., an increase of approximately two and a quarter million barrels over 1937. The principal development during the year was along the Guapo fault, which extends from Point Ligoure to Coora across the southwest portion of the island. This fault has been proved to be a major factor governing oil accumulation in the area. At the southeast end of the fault the Coora field has been actively developed during the year and already ranks as one of the major productive fields of the island. Approximately seven miles to the northwest, another richly productive area has been developed on the north side of the fault at Los Bajos, while several widely spaced wells along the fault in the intervening area suggest that the whole seven miles betwen Los Bajos and Coora will prove productive. The Penal field was placed on regular production during the early part of the year on completion of a pipe line to the Point Fortin refinery. This is a shallow pumping field with a daily output of 2000 to 1500 bbl. of heavy oil. Down-flank extension of the oil-producing structures of Forest Reserve, Kern and Point Fortin have considerably extended the proven acreages on these structures and exploitation of the deeper Cruse sands on these structures has also materially increased the known reserves. Wildcat drilling has been active in several areas. Four wells have been completed in the Mayaro district; four at Moruga; six at Cedros; six in the Morne Diable area; one at Erin and one at Point Ligoure. Few data are available from these areas, but it is understood that some cncouraging results have been obtained. In the northern basin, north of the Central Range, two locations were spudded in at the end of the year after extensive seismograph surveys. Both these locations are scheduled for depths in excess of 10,000 ft. This northern basin is entirely untested by the drill and the present drilling program is being keenly followed by all operators in Trinidad.

Jan 1, 1939

By John W. Roberts

The Federal income tax law permits as a deduction in determining net income "in the case of mines,... a reasonable allowance for depletion and for depreciation of improvements, according to the peculiar conditions in each case, based upon cost, including cost of development not otherwise deducted: Provided, that in the case of such properties acquired prior to Mar. 1, 1913, the fair market value of the property (or the taxpayer's interest therein) on that date shall be taken in lieu of cost up to that date." The law provides for a reasonable allowance but the regulations provide for a definite method of computation that possesses more the virtue of simplicity than that of reasonableness. Article 210 of Regulations 45 reads: "When the cost or value as of Mar. 1, 1913, or within 30 days after the date of discovery of the property shall have been determined, and the number of mineral units in the property as of the date of acquisition or valuation shall have been estimated, the division of the former amount by the latter figure will give the unit value for purposes of depletion, and the depletion allowance for the taxable year may be computed by multiplying such unit value by the number of units of mineral extracted during the year." This is simple, but is it reasonable? The intent of the law is clearly that the cost of the ore in the ground shall be considered as part of the cost of the same ore when removed and sold. The regulations fail to carry out that intent, because of the unwarranted assumption that all the ore in the mine cost the same amount per ton. This is what gives the Treasury Department's method its simplicity, but at the same time robs it of its reasonableness because the assumption is contrary to fact. It is self-evident that a ton of ore near the surface or exposed by present workings is worth much more than a ton buried so far down in the earth that it cannot be removed for many years. If no improvements in mining methods were expected, the value of deeply buried ore would be further reduced by the greater expense that would be required to

Jan 1, 1922

By P. E. T. Connor, O&apos

Production of petroleum in Trinidad during 1938 reached the record figure of 17,737,061 bbl., an increase of approximately two and a quarter million barrels over 1937. The principal development during the year was along the Guapo fault, which extends from Point Ligoure to Coora across the southwest portion of the island. This fault has been proved to be a major factor governing oil accumulation in the area. At the southeast end of the fault the Coora field has been actively developed during the year and already ranks as one of the major productive fields of the island. Approximately seven miles to the northwest, another richly productive area has been developed on the north side of the fault at Los Bajos, while several widely spaced wells along the fault in the intervening area suggest that the whole seven miles betwen Los Bajos and Coora will prove productive. The Penal field was placed on regular production during the early part of the year on completion of a pipe line to the Point Fortin refinery. This is a shallow pumping field with a daily output of 2000 to 1500 bbl. of heavy oil. Down-flank extension of the oil-producing structures of Forest Reserve, Kern and Point Fortin have considerably extended the proven acreages on these structures and exploitation of the deeper Cruse sands on these structures has also materially increased the known reserves. Wildcat drilling has been active in several areas. Four wells have been completed in the Mayaro district; four at Moruga; six at Cedros; six in the Morne Diable area; one at Erin and one at Point Ligoure. Few data are available from these areas, but it is understood that some cncouraging results have been obtained. In the northern basin, north of the Central Range, two locations were spudded in at the end of the year after extensive seismograph surveys. Both these locations are scheduled for depths in excess of 10,000 ft. This northern basin is entirely untested by the drill and the present drilling program is being keenly followed by all operators in Trinidad.

Jan 1, 1939

By J. B. Umpleby

The function of gas in the development and production of oil has far-reaching consequences that should be emphasized. The technical aspects of the subject have recently had a great deal of attention but less thought has been given to fundamental concepts underlying oil and gas law and the many customs and practices that have grown up in the industry. I shall review briefly the advance in knowledge of the subject and attempt to relate these concepts to legislative, judicial and operating problems. Early writers on oil and gas in Pennsylvania noted their close association in oil pools and their contemporaneous decline in output; also, that as gas pressure decreases so does production, that new offset wells reduce the output of existing wells, and even that tubing a well lengthens its flowing life. Expanding gas was deduced as the principal expulsive force. These fundamental observations had been made at least as early as 1880.1 They were treated, however, as academic considerations and did not greatly influence law or practice for many years except to instill into all operators an urgent desire to hasten offset drilling in order to obtain as much of the flush as possible. The most noteworthy later advance in knowledge came in 1926 when Beecher and Parkhurst published their paper on Effects of Dissolved Gas upon the Viscosity and Surface Tension of OiL.² This paper added to the old idea of an expelling force the concept of a modifying agent that actually changes the physical characteristics of the oil and facilitates its movement through the pore spaces of the reservoir rock. Largely since the publication of this paper, intensive study and concerted effort have been given to means of using to a maximum, in producing oil, these combined properties of gas. This is shown clearly by the number of papers dealing with the subject, and the new and revived terms now widely used to express thought, such as the expressions gas energy, reservoir pressure, reservoir energy, gas-oil ratio, bottom-hole pressure, beaning, tapered tubing and back-pressure. These terms, some of which are

Jan 1, 1932

By R. D. Boddorff, R. L. Ash, C. T. Butler, W. W. Kay

DRILLING and blasting in anthracite open-pit mines is a continuous problem to contractors and explosive engineers because of the diverse conditions caused by the nature of the geological formations, the extensive mining of the portions of coal beds near the surface, and the proximity of many strip pits to populated areas. Pennsylvania anthracite occurs in four separate long and narrow fields totaling only 480 sq miles. The coal measures are rock strata and coal beds that are considerably folded and faulted. The crests of the anticlines are eroded extensively. The beds outcrop on the mountain sides and dip under the valleys. At first only the upper portions of the synclines could be stripped. Now stripping to increasingly greater depths is economically possible, as is indicated by the fact that the proportion of freshly mined anthracite produced by strip mining has increased from 3.7 pct of the total tonnage in 1930 to 29.6 pct in 1950. Much of the rock overlying the deeper beds now being stripped is so extensively broken that considerable difficulty is experienced in drilling satisfactory blast holes and in using explosives in such manner as to insure a uniformly broken material easily removed by the excavating machinery. Such breaking of rock strata has occurred because the bed now being stripped has been mined extensively in former years by underground methods, and tops of gangways and chambers have subsequently failed. Draglines are used to uncover coal where the overburden can be moved with little or no rehandling. These machines range in size from those having a 2 cu yd capacity bucket on a 60-ft boom to those handling a 25 cu yd bucket on a 200-ft boom. Draglines are also used to strip to the bottom of the coal basins if the depth and the distance between the crops are not too great. For this type of operation blast holes are drilled full depth to the bed. These holes are commonly 30 to 90 ft deep; however, in exceptional cases, holes may be as shallow as 12 ft or as deep as 130 ft. Drilling is normally done for blasts of 12,000 to 60,000 cu yd of overburden, 30,000 cu yd being considered an average blast if vibration is not the controlling factor. Where the stripping of wide basins or the exposure of a moderately pitching vein makes the use of draglines impractical, dipper front shovels equipped with 4 to 6 1/2 cu yd buckets load into trucks. Overburden is removed in benches of 25 to 30 ft with blast holes drilled 4 or 5 ft deeper than the planned floor of the bench. For shovels under 5 cu yd bucket capacity the volume blasted varies from 8000 to 12,000 cu yd, whereas a volume of 30,000 to 50,000 cu yd of overburden is frequently blasted at one time for the larger shovels where vibration is not an important factor. During the past decade the churn drill, generally the Model 42-T Bucyrus-Erie blast hole drill equipped for drilling 9-in. diam holes, has become the most common blast hole drilling machine. Electricity powers half the churn drills in use and is preferred on the large strippings where electric shovels are operated and the working area is concentrated. On these operations the cost of additional electricity for the drills is less than the cost of fuel to operate diesel units because of the existing large demand load of the excavating equipment. Moreover, electric motors start more easily in cold weather and generally are less expensive to maintain. Diesel driven units are employed where a higher degree of mobility. is required. The average drilling speed is 8 ft per hr, although in softer rocks a rate of 15 ft per hr is attained. Where rock is hard and strata is badly broken, drill speeds may ' be less than 2 ft per hr. Low drilling production results under these circumstances when loose material falling from the upper portion of the drill holes causes drill stems to be jammed. Rock formations vary so greatly in the region that a 9-in. diam churn drill bit may become dull after drilling only 2 ft or may drill satisfactorily for 56 ft; however, an average of 35 ft is usual in sandstone of medium hardness. Dull bits are hoisted to flat bed trucks by the sand line of the drill and are usually sharpened in the contractor's bit shop adjacent to the job. Care is generally taken to cover the thread end of the bit with a cap. To facilitate handling of bits around the drill, a heavy thread protector having an eye top is becoming more popular than the flat-top rubber or metal cap furnished with new bits. The 9-in. diam blast holes for a 25 to 30 ft bench are normally on 18x18 ft to 20x20 ft spacings, depending on the character of the overburden, although in broken ground 15x18 ft centers may be used to obtain better breakage and a more even bottom for the bench. The patterns of holes for shots

Jan 1, 1952

By W. C. Lacy

A WIDE variety of metalliferous deposits in Peru shows a close and consistent relationship to intrusive and extrusive igneous rocks. This relation- ship furnishes a clue to the composition of ore-bearing fluids and to the timing in separation of these fluids from differentiation magma. Conclusions presented here are based on ten years' study of a large number of metalliferous deposits in Peru. The most important of these areas are shown in Fig. 1.

Jan 5, 1957