Search Documents

By Harold Markus, Arthur H. Grobe, Gerhard Derge

THE high corrosion resistance possessed by tin under most circumstances, combined with its generally satisfactory appearance and useful physical properties, has led to many and varied uses for the metal. These uses have been partly limited by the fact that tin is an expensive metal, therefore many applications have been developed in which tin has been employed in combination with lead, either by coating, as in tin-lined collapsible tubes, or by the formation of alloys containing various proportions of tin-rich and lead-rich phases, as terne plate. A detailed knowledge of the corrosion characteristics of the tin-lead couple therefore is of general interest and has become specially important at the present time, when every effort is being made to conserve tin as much as possible. The present study. has been limited to carbonate solutions with a pH range from 8.4 to 11.2 so that the results may be related to earlier work on the corrosion of tin and its alloys.1-3,6 In these papers, the effects of a number of anion and cation additions to these solutions have been observed. APPARATUS AND METHOD The electrodes for the corrosion cell were cut from rolled sheet about 1/16 in. thick. The length of all specimens was held constant at 7 in., while the width was varied from 1/2 to 2 in. These electrodes were fastened to brass electrode supports, which were attached to rubber stoppers fitting into tall-type one-liter Pyrex beakers that contained the electrolyte. The lead electrodes were prepared from Omaha pig* and the tin was rolled from a slab of Chempur.? After cutting to size, the sheets were polished with No. I emery paper and cleaned with carbon tetrachloride. The edges, back and upper parts of the specimen were coated with a synthetic lacquer, which was supplemented with beeswax for the lead electrodes. The binding posts were coated with beeswax after the electrodes had been damped. The pH of the electrolyte was controlled? by adjusting the ratio of carbonate to bicarbonate. Approximately 600 ml. of electrolyte was used in each beaker. The entire assembly was placed in an oil bath thermostatically adjusted to operate at 30°C. ± 0.10. Potentials were measured against a saturated calomel electrode connected. to the cell by an agar-agar salt bridge. The carbonate solution used in the salt bridge was the same as that used in the corrosion cell. Currents were measured with a milliam-

Jan 1, 1942

By E. P. Klier, S. M. Grymko

The transformations in eutectoidal systems have been extensively studied as they occur in steels.&apos; As a consequence of these studies the martensite, bainite and pearlite reactions found for most steels are widely recognized. Further, because of the work of Smith and Lindlief2 and of Greninger and Troiano3 these reactions, except for the bainite reaction, are considered as typical for all eutectoidal systems. The primary alloy studied by Smith and Lindlief2 was a CuAl alloy of near eutectoid composition as was the alloy more recently studied by Mack.4 The transformations in these alloys were, for the most part, studied metallo-graphically, while an X ray analysis of structures was essentially wanting. It has appeared desirable, therefore, to investigate selected CuAl alloys at and slightly away from eutectoid composition. For this purpose three alloys were prepared containing 10.5,11.9 and 13.5 pct A1 respectively. The results of a metallographic and X ray analysis of structures obtained for isothermal transformation of the ß-phase are reported here for the 11.9 and 13.5 pct A1 alloys. Introduction The phase equilibria in the CuAl alloys of immediate concern are indicated in the equilibrium diagram section presented in Fig 1.5 The equilibrium and transition structures which have been reported in this system are as follows: a = copper rich terminal phase (f.c.c.) ß = high temperature eutectoidal phase (b.c.c.) r2 = aluminum-rich intermediate phase (r-brass structure) a&apos; = modified a-phase postulated by Bollenrath and Bungnrdt.26 ß1 = ordered ß (b.c.c.) ß&apos; = martensite structure: A1 < 13 pct (near h.c.p.) ß" = ß&apos; of Smith and Lindlief2 7&apos; = martensite structure: A1 > 13.5 pct (h.c.p.); ß2 of Bollenrath and Bungardt.26 The eutectoid transformation can be suppressed at sufficiently high cooling velocities. The ß-phase is then retained to about 500°C where ordering sets in. The ordering interval is not satisfactorily known but indirectly appears to be non-suppressible. Subsequent to the ordering reaction and consequently at lower temperatures, the ordered ß1 decomposes to a marten-sitic structure. The kinetics of these reactions and in particular those of the martensite reaction have an important bearing on the results obtained in this investigation. Since some confusion exists concerning certain reported aspects of these reactions, they will be considered in some detail. THE MARTENSITE REACTION The martensitic structure is formed on cooling through a critical range6

Jan 1, 1950

By C. O. Lee, Z. W. Bartlett, R. H. Feierabend

DESPITE the fact that American brimstone production has increased 2 ½ times since the prewar period 1935-1939, the demand for sulphur exceeds the supply. To alleviate this situation efforts are being made to increase the production of sulphur and bring the shortage to an end. The most important developments are being undertaken on the Gulf Coast. One new brimstone mine has been put into operation and three others are being developed. These projects are expected to account for a large part of the additional sulphur production now anticipated for the free world.1,2 Except for a small amount of byproduct sulphur from sour natural gas and refinery gases, American brimstone is produced by the same process devised by Frasch 60 years ago, consisting essentially of the injection of superheated water at about 325°F into sulphur-bearing formations through wells which are drilled from the surface by standard oilfield methods. Sulphur deposits vary in depth from a few hundred feet to 2500 ft from the surface; in a typical deposit the sulphur occurs as crystalline aggregates in porous limestone and gypsum in concentrations varying from 5 to 40 pct, the thickness of the formation ranging from a few feet to several hundred.3 The deposits are usually surrounded by formations impermeable to the flow of hot water, the top and sides being enclosed by impermeable sediments and the bottom by dense impermeable anhydrite. As the hot water leaves the well bore, it percolates through the formation and transmits its heat to the rock and sulphur. When the sulphur reaches 240°F it melts, separates from the rock, and flows through the hot channels downward to the bottom of the well. Here it is freed from incoming water and from formation water, which saturates the porous rock, by gravity separation, liquid sulphur being 1.8 times as heavy as water. It then is pumped to the surface in a relatively pure state, 99.5 pct or better. Chief contaminants are organic impurities, such as petroleum residues, which are soluble in sulphur and tend to discolor it.4 Sixteen deposits of commercial magnitude have been discovered in the Gulf Coast area. Five of these deposits have been depleted and abandoned with production totalling more than 26,886,000 tons. Eight properties are operating and have produced 65,875,000 tons to Jan. 1, 1952, for a total Frasch-type production of 92,761,000 tons. Three new deposits are under development. Aforementioned deposits are listed in Table I. Each of these deposits has been found in the caprock overlying shallow intrusive salt plugs or domes and buried in several hundred to as much as 2500 ft of sediments. All salt domes do not contain sulphur; only 16 sulphur deposits have been found in a total of 231 salt domes which are known to exist in the Gulf Coastal states of Texas, Louisiana, Mississippi, and Alabama. Ten of the salt domes lie in the Gulf of Mexico offshore from the Texas and Louisiana coasts. Additional offshore domes may be found, but their value as a sulphur potential is questionable owing to the great hazard and high cost that can be visualized at these exposed locations where depths of water reach 50 ft. Marsh operations of Freeport Sulphur Co. are in the southeast section of Louisiana. In general, the country is low, flat, relatively uninhabited marshland broken by many shallow lakes and bayous which extend for irregular distances inland. Geologically, the coastal area is of sedimentary origin, having been built up gradually under the sea by deposition of material carried down by large streams to their deltas. Offshore bars were formed enclosing

Jan 1, 1952

By Z. F. Oszter

This paper discusses the materials handling problems encountered in cement plants in the areas of raw and finished product grinding and cement storage. It illustrates by examples taken from actual installations, how optimum feed rate is maintained in grinding circuits with properly applied bin dischargers (vibrating hoppers, Mexican feed boxes and aerated bin bottoms) for materials with high moisture content and/or difficult handling characteristics. Initial operating problems with the equipment will be discussed and maintenance requirements will be indicated for comparison purposes. In a modern cement plant, properly functioning bins and feeders are as essential as process control, for no process control system, however sophisticated, can perform efficiently if raw materials do not flow into the plant processing facilities at the required time and rate. Most materials used in the manufacture of portland cement - such as silica sand, iron ore fines, crushed limestone, gypsum, clinker or cement itself-have difficult handling characteristics under specific conditions. High moisture content or even dampness due to condensation may create bin hang-ups, arching and ratholing, all of which result in improper functioning of the feeders or proportioning equipment. The occurrence of these problems in existing cement plants spurred a search for the corrective devices discussed in this article. The equipment investigated included bin dischargers in the form of vibrating hoppers for moist raw materials, Mexican feed boxes for clinker and aerated bin bottoms for cement. Operating experience with different types of bin dischargers showed that the actual performance of some did not come up to the expected level under prevailing operating conditions. The aim of this paper is to record the results of this experience and there- by aid designers and/or operators in selecting the most suitable equipment for their requirements. BIN DISCHARGERS (GENERAL) A discharger is a device that causes stored solids to flow out of a hopper without metering the rate of flow as a feeder does. The investigation discussed here encompasses the following types of bin dischargers used in a cement plant: (1) vibrating hoppers (horizontal motion), (2) whirlpool hoppers (horizontal and vertical motion), (3) aerated bin bottoms (air fluidization), and (4) Mexican feed boxes. Most of the bins used in the cement industry are of the plug flow type. Raw materials with difficult handling characteristics such as high moisture content may cause flow problems when fed through small openings (12 x 18 in.), even if two walls of the bin are vertical.&apos; The most appropriate solution to these flow problems would be the installation of separate mass flow bins for the different materials such as silica sand, iron ore fines, crushed limestone and gypsum, with each bin correctly designed from test data obtained by measuring the flow properties of representative samples. However, limited storage capacity and plant space usually preclude this approach. Quantitative design of bins for flow based on measured flow properties of representative samples of the bulk solid to be handled is no longer an "engineering art," thanks to the basic research done on the flow of bulk solids in bins during the last decade.2, Where space limitations exist, however, or where improvements are being sought for equipment already installed, bin dischargers offer a satisfactory solution to flow problems. They can be applied effectively under flat-bottom bins or mounted to existing plug-flow bins with very little modification to these facilities. In both the foregoing cases, plug flow will be maintained, but the flow channel will be considerably increased so that it is larger than the discharger&apos;s bin-side diameter, and material flow can be sustained if the discharger is correctly selected. The main purpose of a bin discharger is to draw the bulk solids across the whole area of the bin outlet, to make the opening fully effective. As long as the bin-side opening of the discharger is large enough

Jan 1, 1969

By K. A. Natarajan, I. Iwasaki

The influence of dissolved oxygen and the Pt - Pt-O reaction on the measurement of redox potentials in solutions containing ferrous-ferric couple was examined. Current-potential curves were used to illustrate the shift in measured potentials toward the oxygen potential in oxygenated and deoxygenated systems at low concentrations of ferrous and ferric ions. The ranges of concentrations of the ferrous-ferric couple, in which the interference from oxygen and the platinum-oxygen reactions becomes significant, are illustrated through the mixed potential mechanism.

Jan 1, 1975

By Thomas A. Simpson

THE Birmingham red iron ore district in Jefferson County, north central Alabama, Fig. 1, is bounded on the northwest by the Warrior and Plateau coal fields and on the southeast by the Cahaba and Coosa coal fields. The area of study includes the ridge and valley between Red Mountain and Shades Mountain, Fig. 2, approximately 70 square miles extending from Homewood in the northeast to Greenwood in the southwest. The district is one of the most important producers of hematite in the United States, with an annual production of about 7 million tons. The amount of hematite mined between 1870 and 1950 ranged from 6 to 16 pct of the nation&apos;s total annual production, and the iron and steel products from blast furnaces in the Birmingham district supply the entire southeastern section of the country.

Jan 1, 1955

By K. C. Ko, M. K. McCarter

Experimentation with seismic velocity measurements at Kennecott Copper Corp.&apos;s Bingham mine disclosed that some recognized slide areas are characterized by low velocity profiles. A new traverse technique employed during the investigation allows rapid and precise measurements of a quantity referred to as "apparent velocity." This value is a weighted average of the actual velocity in the overbreak zone near the surface and in the intact rock at depth. The low points on the velocity profile are apparently the result of lower actual velocities and deeper overbreak in less competent material within the slide zones. Experience verifies the usefulness and practicality of the technique in delineating adverse areas prior to detectable failure. The technique may be employed as a rapid and economic means of slope stability surveillance in large open pit mines.

Jan 1, 1973

By P. Payson

INTERGRANULAR corrosion in corrosion-resistant chromium-nickel steels has been widely discussed in the last few years. So far as the author knows, nothing has been published which definitely shows that this tendency can be eliminated, although suggestions have been made that a remedy is possible if certain specifications are satisfied. Strauss, Schottky and Hinueber1 suggested an increase in chromium content to an extent that would prevent the impoverishment of chromium on carbide precipitation sufficient to cause impaired corrosion resistance in the matrix. Pilling2 suggested an increase in nickel, so that the stability of the austenite matrix would be increased. Aborn and Bain,3 say that "intergranular attack-may be eliminated by preventing carbide precipitation (e. g., by lowering the carbon content or somehow raising its solubility) or by precipitating it permanently under conditions which will not remove chromium from solid solution so drastically at any points." In a later paper Aborn and Bain4 state that many different metallic elements, tungsten, vanadium, copper, aluminum, molybdenum, titanium and zirconium, have been added in small per-centages to increase the stability of these alloys, but that it has been reported that according to the copper sulfate test these added elements act only to retard the intergranular corrosion, and that increased nickel and chromium contents have similar effects. Newell5 showed that the lower the quenching temperature before reheating, the less severe was the intergranular attack.

Jan 1, 1932

By C. C. Clark, J. R. Mihalisin, K. G. Carroll

OBSERVATIONS made in this paper were for the purpose of exploring the anomalous behavior of a particular heat of Type 310 stainless steel. The alloy, of nominal composition 25 pct Cr, 20 pct Ni, was observed to form a grain boundary precipitate at exceedingly high rates. A sheet of this metal, 0.060 in. thick, after cooling in air from 2000°F showed the presence of the grain boundary material, whereas none was found after water-quenching from the same temperature. X-ray techniques were applied without success and, in view of the ex-

Jan 1, 1958

By R. W. Raymond

In connection with the discussion of the paper of Mr. James Gayley, presented at the Baltimore meeting, in February, 1892, on " The Preservation of the Hearth and Bosh-walls of the Blast-furnace,"* I offered a translation of a letter received from our distinguished honorary member, Professor P. Ritter von Tunner, concerning the use of carbon-bricks at the Donawitz furnace, then (February, 1892) in the third month of its campaign. The purpose of this brief paper is to put upon record later results of practice with carbon-bricks, both in this country and abroad.

Jan 1, 1897

By Huey-Lin Luo, T. R. Anantharaman, William Klement

Two new metastable phases have been obtained in Au-Ge alloys by rapid cooling from the melt. One is of the hep structure with near-ideal axial ratio and may be considered a Hume-Rothery phase. The other has a complex tetragonal structure (a = 11.627Å and c = 22.191Å for the Au60Ge40 alloy) and may be looked upon as a superlattice made up of forty-four fee unit cells. Alloys with the tetragonal phase are charactevized by marked preferred orientation. The metastable constitution of the Au-Ge alloys is discussed with reference to the rate of cooling from the melt. THE Au-Ge equilibrium diagram features a rather deep eutectic near 27 at. pet Ge with a maximum solid solubility of 3.2 at. pet Ge in gold and is similar to the Ag-Ge, Ag-Si, and Au-Si diagrams.&apos; The present study of the effects of rapid cooling from the melt on the structure of Au-Ge alloys constitutes an extension of similar investigations2-8 in this laboratory on alloys of noble metals with germanium and silicon. Nonequilibrium hep structures have so far been obtained by quenching Ag-Ge2, 3 and Ag-Si4, 5 alloys from the melt; an Au-Si alloy of approximately eutectic composition has been found6 to solidify in a noncrystalline state. EXPERIMENTAL PROCEDURES Twenty-nine alloys prepared from gold of 99.9+ pet and germaium of 99.999 + pet purity were investigated. The method of alloy preparation, the technique of rapid quenching from the melt, and the X-ray diffraction procedures were similar to those described previously.3, 4 Essentially, small sections (-20 mg) of thin alloy rods (-1 mm diam) were rapidly heated up to 1200°C in a graphite crucible under argon and the liquid alloy ejected by a helium blast onto a polished copper strip held on the inner periphery of a rotating wheel. The resulting thin foils were examined with or without the copper substrate in a G.E. X-ray Diffractometer or in a 114.6-cm-diam Debye-Scherrer camera. RESULTS Table I gives the constitution of liquid-quenched Au-Ge alloys, as estimated from intensities of X-ray reflections from the corresponding phases, viz., a (fee solid solution), ß (hep phase), ? (tetragonal phase), and diamond-cubic (dc) germanium. Despite unavoidable variations in the quenching rates, the proportions of the phases in different alloys were generally reproducible and stable at room temperature. There was no evidence of quenching strain, since the a doublets were well-resolved in high-angle Debye-Scherrer reflections in all cases except where stacking faults in the a fee and ß hep structures contributed to X-ray line broadening. The ß and ? metastable phases showed signs of decomposition to the equilibrium a phase and germanium only after a few hours annealing above 100°C. A few alloys around the eutectic composi-

Jan 1, 1965

By R. N. Orava

TO the author&apos;s knowledge, only one satisfactory high-resolution technique for etch-pitting dislocations in Cu-Zn alloys has been published.&apos; In that account, pits in 70/30 brass single crystals were produced by etching electrolytic ally in a 30 pct orthophosphoric acid bath. Thereafter, observations were made from surface replicas by electron microscopy. The method of pitting and observation permitted the high resolution necessary for the distinction of individual dislocations in arrays of pile-ups. However, no comment was offered concerning the possibility of obtaining pits which are amenable to optical resolution. Moreover, for adequate results, the electrolytic pitting process is invariably preceded by a polishing stage which could obscure the surface features of interest. Consequently, it would be desirable to be able to delineate, by solely chemical means, dislocations which could be detected by both optical and electron metallo-graphic techniques. This was achieved by the simple expedient of modifying two etchants reported by young2 to reveal dislocations on the (100) planes of pure copper. Single crystals of 70/30 a brass, described previously,3 were sectioned to provide a surface parallel to a set of {100) planes, mechanically polished, and subsequently electropolished at 2.4 v in a solution comprised of 2 parts H3PO4, 4 parts ethanol, and 3 parts water. The inclusion of ethanol tended to inhibit nonuniform surface attack. Etch-pitting was effected by a 2 to 3 sec immersion in a 70 pct aqueous solution of HNO3. The samples were then washed in a fast-flowing stream of water, and rinsed further in distilled water, and ethanol, before drying. It is important to note that this reagent should be either used immediately after mixing, or, if allowed to cool, reheated to about 35°C prior to use. No pitting was obtained at room temperature. Typical results are shown in Fig. 1 where (a) is an optical view of the pitted surface and (b) is an electron micrograph of a silicon monoxide replica shadowed with tungsten oxide. The former is characteristic of a somewhat longer etching time (-6 to 8 sec) which varied with bath temperature. Similar pits accrued from a 1/10 aqueous dilution of another of Young&apos;s solutions2—2 M FeC1,6H20 and 7.8 M HBr.

Jan 1, 1968

By John C. Smock

THE question of the proper valuation of mines of iron ore was suggested to me by the difficulties experienced in getting answers for the United States Census Office, while I was engaged in the work of collecting the statistics of mines in New Jersey and New York The answers to the questions relating to values of real estate of mine properties varied so greatly that it was necessary to revise them according to some general principles of valuation. Generally the returns of mine proprietors Seemed to be too low. There were, however, examples of what would be termed excessive valuation. The Subject appeared to be of practical importance, and led to the paper here presented. The following table of selected mine statistics is given, prefacing the discussion of the principles of valuation. It is in part made up of census returns and partly of data obtained directly from mine owners and managers. The mines which were Selected for the Several groups and mining districts include nearly all of those from Which the more full and carefully filled returns were received, and are also representative of their respective districts. Hence the averages obtained from them become good types of these groups or districts. The mines of New Jersey appear in Six groups, each containing from three to eleven mines, or, in all, thirty-four mines. The magnetic iron ores of New York are in four well-marked groups, and there are twenty-six mines in them. Then follow the red hematite mines of St. Lawrence and Jefferson counties; and, lastly, the brown hematite groups of Dutchess and Columbia counties, and those of the adjacent parts of Connecticut and Massachusetts. The whole number of mines represented by the table is eighty-eight, of which twenty-eight are hematite mines. The first column gives the value of the real estate; the second that of the plant; the third is the sum of these two, or the capital invested. Then follow the number of men employed, the amount of wages paid during the census year, and the value of materials used in mining and preparing the ores for market.* The seventh column gives the total expendi- * The value of materials is somewhat uncertain in many cases, as royalties are included under this head. Likewise, under wages, the cost of explosives and light is often included. Hence it is impossible to draw the line sharply between these items of expenditure.

Jan 1, 1882

By J. G. Davis, P. C. Thakur

Hazardous methane gas in coal mining is receiving increased attention due to the increased US demand for coal which has resulted in the exploitation of deeper seams and the utilization of more productive equipment. Problems posed by methane emission has the Mining Research Division of Continental Oil Co. (Conoco) accelerating efforts that began in the early 1950&apos;s with Consolidation Coal Co. (Consol).1 The program&apos;s focus is on finding new techniques for degasification of virgin areas as well as control of methane in gob areas.

Jan 10, 1977

By L. Seigle, R. Resnick

An inert-marker movement experiment indicates that the ratio of the intrinsic diffusion coefficients DC:DTa = 80:l in TaC at 2500°C. Measurements of the diffmion coefficient of carbon in nonstoichiometric TaC at temperatures from 1700° to 2700°C reveal that Dc increases with decreasing carbon content, but much less than expected from the probable change in vacancy concentration with carbon content. A diffusion process involving two simultaneously operating mechanisms is postulated, and shown to be theoretically feasible. The average value of the carbon diffusion coefficient is given by DC = 0.18 exp[(-85,000 ± 3000)/RT] sq cm per sec over the composition range 46 to 49.5 at. pct C. BECAUSE of their high melting points and hardness, the carbides of the IV, V, and VI group transition metals, along with those of uranium, have attracted considerable interest for applications at high temperatures. In these applications the reactivity of the materials is important, and, since rates of diffusion within the compounds influence reactivity, a knowledge of diffusion kinetics and mechanisms is desirable. While many investigations of the mechanical and electrical properties of these compounds have been made, only two fundamental investigations of diffusion in the carbides are known. Chubb, Getz, and Townleyl measured the diffusivity of carbon and uranium in UC, and Gel&apos;d and Liubimov2 measured the diffusivity of carbon and niobium in NbC. This paper describes an investigation of the diffusion of carbon in tantalum monocarbide and, in particular, the influence of carbon deficiency on this process. Tantalum carbide melts at approximately 3800°C, which makes it one of the highest melting materials known. The compound exists over a rather wide range of carbon Content.3-7 At the peritectic temperature, 3240°C, the phase extends from about 36 to 50 at. pct C. Although the compound can exist with a substantial carbon deficiency, the high carbon phase boundary remains near the stoichiometric composition over the entire temperature range; i.e., no carbon excess is observed. The structure of TaC is the NaCl type wherein carbon atoms normally occupy the octahedral sites in a somewhat expanded fcc lattice of tantalum. Decrease of the lattice parameter with decreasing carbon suggests that the removal of carbon introduces octahedral vacancies into the lattice. I) EXPERIMENTAL DETAILS AND RESULTS Inert-Marker Experiments. In a compound such as TaC the interstitial element would be expected to diffuse more rapidly than the metal. This was confirmed by an inert-marker experiment, following Srnigelskas and irkeendall.8 Ideally, the markers should be placed at the interface between a slab of low-carbon TaC and graphite, and their movement during subsequent inter-diffusion measured. Unfortunately, no solid could be found which is unreactive in contact with carbon at the high temperatures employed in these experiments. In order to circumvent this problem, a specimen was designed in which the markers consisted of several small canals running just below the surface of a tantalum slab. This specimen was prepared by machining grooves on the surface of the tantalum slab and then diffusion-bonding a thin plate of tantalum to the slab over the grooves. The surface of the plate was then ground down until the distance between the canals and surface was as small as possible (about 0.01 cm). Thus, the canals would lie entirely within the TaC phase after a short period of diffusion. The diffusion anneal consisted of immersing the metal sample in high-purity graphite powder and heating for approximately 10 hr at 2500°C under vacuum. At this temperature, the vapor pressure is sufficiently high and the transfer of carbon from graphite sufficiently rapid to allow the surface of the diffusion sample to attain the stoichiometric carbon concentration very quickly. Conclusions regarding the relative diffusion rates of carbon and tantalum in the compound layers (TaC and Ta2C) can be drawn from the location of the canals after the diffusion anneals. If the growth of the layers is governed mainly by the diffusion of carbon, as expected, the canals should remain close to the sample surface. If the diffusion of tantalum contributes appreciably to formation of the compound layers, the distance from the markers (canals) to the surface should increase. Fig. 1 shows, diagrammatically, the appearance of the specimens after diffusion, and Table I presents the depth below the surface at which the

Jan 1, 1967

By T. S. Lundy, C. J. McHargue

HE diffusion rate of v48 in single crystals of bee vanadium has been determined at temperatures from 1002° to 1888°C. Standard techniques of lathe sectioning were used for specimens annealed above 1500°C while sectioning by grinding was used for specimens annealed at lower temperatures. As will be seen, the lower-temperature data is enhanced on an Arrhenius-type plot relative to values expected by extrapolation of the high-temperature data. Single crystals were obtained from Linde Co. In Table I the analysis supplied by the vendor is compared with an analysis at Oak Ridge National Laboratory of a sample after a diffusion anneal. The isotope v4&apos; was prepared by the Isotopes Division of Oak Ridge National Laboratory. Proton bombardment of a titanium target in the 86-Inch ORNL Cyclotron was followed by a carrier-free chemical separation. Nineteen specimens, 1/2 in. diam and 3/8 in. long, were cut from the as-received vanadium single crystals. Each specimen was machined with the flat face perpendicular to the longitudinal axis. Specimens were polished through 1/0 emery paper and were etched with 25 pct HF-10 pct H2SO4-10 pct HNO3-55 pct H2O. The polishing and etching steps were repeated until a satisfactory surface finish was achieved. The isotope was electroplated onto the specimens from a neutral solution. Counting rates of the deposited layers were approximately 100 counts per sec. At temperatures above 1200°C specimens were annealed in a tantalum resistance furnace under an argon atmosphere. Temperatures were measured with a Pyro micro-optical pyrometer and a Pt-Pt 10 pct Rh thermocouple. At lower temperatures the specimens were sealed in evacuated quartz ampoules and annealed in Kanthal wire-wound horizontal tube furnaces. A severe reaction occurred at 1200°C between the quartz and the vanadium. This

Jan 1, 1965

By E. E. Bach

STATEMENT OF THE PROBLEM THE administration of industrial organization today embraces more than the cost of production and selling prices. Competition is deeper seated than mechanical devices, overhead charges, and a shrewd manipulation of the markets. Despite the "down-to-the-minute" equipment and the "last word in organization," it is quite evident that "capacity production" will be an unknown quantity until the workman is considered as a producer, in relation to his home, as he is now considered in relation to industry. Whether or not a man shall do an honest day&apos;s work is as much a psychological condition as it is a matter of physical strength or skill. His attitude toward his work each morning is determined, to a large degree, by the environment of his home. Whether this attitude, good or bad, obtains the day through will depend entirely upon the one fact as to whether the corporation which employs him does or does not differentiate between the mechanical factor and the human factor in industry. To be more specific, sociological work, under whatever name, should be of such a character as to influence the life of a workman in such a manner as to establish a cooperative interest in his work, foster within him a spirit of contentment in his home, lead him-so to employ his leisure time that he will not lower his efficiency as a workman, destroy his domestic happiness, or endanger his standing in the community as a citizen. While no fixed rules of procedure can well be formulated for the development of the work, yet definite lines of activities will readily present themselves as applicable to the individual needs of a community. This is especially true where community influences and agencies pertaining to general welfare are easily correlated.

Jan 2, 1918

By F. Weinberg

INTEREST is currently being directed toward grain boundary morphologies in zinc in terms of grain boundary facetingl and grain boundary energies.&apos; Some years ago the present author attempted to measure grain boundary energies in 99.999 pct purity Zn as a function of boundary angle, using the standard procedure of measuring equilibrium angles of the boundary traces at triple points. This followed an investigation he carried out on preferential melting of |H (112) Fig. 1—Electron transmission micrograph of a stacking fault, grain boundary intersection in copper. GRAIN BOUNDARY STACKING FAULT Fig. 2—Schematic representation of the intersection of Fig. 1, indicating inclination angles 0 and trace angles $. specimens were prepared by the Bollman technique in an electrolyte of 70 pct methanol, 30 pct HNO3 main-tained at -30°C. The interfacial free energy of the high angle grain boundary and of the stacking fault is assumed to be thermodynamically equivalent to the corresponding in-terfacial tensions. In terms of the true dihedral angles & between the intersecting interfaces, the equilibrium of interfacial tensions in the direction parallel to the stacking fault yields: ysF = -ygb(cos F1+ cos ±cosF2) Here, ysF is the stacking fault free energy and ygb is the grain boundary free energy, assumed equal on both sides of the intersection. Forces acting normal to the grain boundary, of the form ??gb/?F,l are assumed negligible as the grain boundary remains straight for a considerable distance on either side of the intersection. The micrograph of Fig. 1 may actually consist of several closely spaced stacking faults on the same slip plane. The actual point of intersection between the grain boundary and the first stacking fault, and the equilibrium configuration of the intersection, should not be affected by the presence of the other faults, as

Jan 1, 1970

By K. Thirumalai

Although the term "spalling" has long been known, Norton l first referred to its usage for the fracture or disintegration of materials subjected to rapid temperature changes. Spalling of ceramic materials at high temperatures has received attention in the past.2-4 Removal of the char formed during ablation in reentry of space vehicles has been referred to as mechanical spalling.5 The first experiments to evaluate the process of rock fragmentation by thermal spalling were conducted by Stoces6 using a series of gasoline burners on the quartz veins of the Zinnwald deep mines in Germany. After the development of rocket-jet burners, the principles of thermal spalling combined with high fluid momentum found wide practical application in rocks. The well-known jet piercing process for drilling blastholes in taconite and for jet channeling in the quarrying of granite are among the more notable of these application.7 For the purposes of this study, thermal spalling or spallation of rocks is defined as progressive failure caused by thermal stresses induced by a sudden application of heat from a high temperature heat source. Gray observes that the size of the spall is dependent on the pattern of induced thermal stresses before failure. The spallability or the relative susceptibility of rocks to failure by thermal spalling is a complex but potentially useful parameter for qualitative comparisons. Fundamental differences exist in the degree of spallability among different types of rocks. Accurate prediction of spallability of any particular rock has so far not been possible. Measurement of the state of stress and temperature in the rock during the rapid thermal spalling process poses difficult problems that must be solved. Identifying the parameters that influence the thermal spalling proc-

Jan 1, 1970

By Jerome Alexander

The object of this paper is to show that many of the important phenomena of metals and alloys are due to the facts that, at some stage, metals and alloys, or some of their constituents, are in a colloidal state and that a portion of the metal or alloy tends to remain in this state. The so-called amorphous phase in pure metals is an isocolloid, consisting of colloidal groups of metal molecules that may be dispersed in still more finely subdivided metal; these colloidal particles are not truly amorphous, but may consist, in part, if not entirely, of ultramicroscopic crystals; as a result the expressions amorphous phase and amorphous theory might he replaced by the expressions colloidal phase and colloidal theory. Any substance is in the colloidal state when the constituent particles consist of molecular or atomic groups, whose size varies approximately from about 100 down to about 5pp, that is from just below the limit of microscopic resolvability to the dimensions commonly ascribed to the larger molecules. Colloidality involves no assumption as to the shape, internal structure, or orientation of the colloidal particles; size alone is the critical factor. A colloidal system may therefore contain crystalline groups, or amorphous groups (non-crystalline, random or haphazard clusters), or a mixture of the two. All colloids consist of at least two phases, the subdivided substance, or dispersed phase, and the substance into which this is subdivided, the dispersion medium. It is not necessary that there be any chemical difference between the dispersed phase and the dispersion medium. As molecular forces are extremely powerful, their application may produce marked changes in the physical properties of metals. It is doubtful whether metal in the interior, especially of large masses, possesses the same properties as that on or near the surface, which alone is open to inspection.

Jan 1, 1921