Search Documents

By Franklin Allison

THE influence of cobalt and nickel on the properties of steel might be readily expected to be very similar. The two elements occupy close and somewhat unusual positions in the periodic table, their chemical behavior and compounds are so completely analogous and their various physical properties, including the ferro-magnetic characteristic, show such a remarkable correspondence, that there is no doubt of a strong resemblance existing between these two metals. However, the variety of, properties that are obtained from steel is due, largely to the fact that the element iron possesses allotropic forms. Alloying elements that affect these allotropic forms, or alter the nature of the allotropic changes, exert a profound influence on the resulting steel. In the case of nickel and cobalt, although these elements are very similar chemically and physically, it is found that they differ distinctly in their individual effects on the critical points of iron. Both nickel and cobalt form a series of homogeneous solid solutions with iron at temperatures above 1800° F. The difference in their behavior does not occur until changes begin to take place in the solid state below this temperature. An inspection of the respective thermal equilibrium diagrams at the lower temperatures makes the opposite effects of nickel and cobalt clearly evident.

Jan 3, 1927

By O. A. Knight

THE suppression of the austenite-martensite transformation that can be brought about by the addition of certain alloying elements, such as manganese or nickel, to plain carbon steel has been known for a long time, especially since Guillet's investigation at the beginning of this century. The extent to which the critical range is lowered depends upon the percentage and nature of the special element added. First the Ar1 point is lowered gradually, then at a certain percentage a sudden lowering to about 300° C. occurs. The addition of still larger percentages of the alloy may result in lowering the Ar1 point to room temperature or below, in which case the steel remains austenitic at room temperature, especially after rapid cooling. The effect of alloying elements of this general type on the lowering of the transformation temperature is well illustrated by Sauveur(1)§ in his Fig. 281a, reproduced here as Fig. 1. This type of curve is characteristic of both manganese and nickel though it requires about 2 1/2 times as much nickel as of manganese to produce the same result. The influence of nickel in retarding the transformation of austenite into the lower transition constituents is due to its lowering of the critical range of the steel, which is also well illustrated by Sauveur(1) (after Osmond) in his Fig. 284, reproduced here as Fig. 2. Scott(15) presents a diagram illustrating the effect of manganese on the Ac3 and Ar3 points which is strikingly similar to the diagram above referred to in Fig. 2 concerning the effect of nickel.

Jan 1, 1934

By J. J. Rutledge

FULLY 60 per cent of the serious and fatal accidents in Maryland coal mines are due to falls of roof and side. Usually, the victim of the fall sustains a broken back, sometimes not only the vertebrae being fractured but the spinal cord also being severed. When the spinal cord has not been severed and yet the vertebrae have been broken or injured, it is often possible to rehabilitate the victim of the broken back. - Such accidents are classed as Permanent Total and the victim receives a certain compensation from the State Industrial Accident Commission; sometimes the amount is awarded in a lump sum, but usually it is paid weekly. When the amount allotted to the victim of such an accident has been expended, either in a lump sum or weekly payments, the victim of the accident is dependent on public charity. Some efforts have been made to physically rehabilitate the victims and make them at least partly self-supporting before the expiration of their compensation payments. The State Industrial Accident Com-mission has done some of this rehabilitation. The Maryland Bureau of Mines, in cooperation with R. C. Thompson, Supervisor of Vocational Rehabilitation, State Department of Education, and his assistants, has, through an informal cooperative arrangement, placed several of the victims in hospitals in Baltimore for treatment. Six years ago, through the efforts of the Maryland Bureau of Mines, a dozen or more broken-back victims were examined by an orthopedic surgeon and report was made to the Bureau regarding such cases and the possibility of their rehabilitation. This paper details the result of such examinations.

Jan 1, 1936

By U. K. Custred, E. W. Long, V. R. Degner

In 1973, the United States production of marketable phosphate rock set a record in excess of 42 million tons. This production rate is expected to continue to increase, due to the growing international requirement for fertilizer, at a rate exceeding 5% per year well into 1977. One approach towards increasing plant production capacity to meet the growing demand is through large-capacity flotation cells, provided they achieve metallurgical performance comparable to existing smaller cells. A 9-month evaluation test program recently completed at the Haynsworth mine at Bradley, Fla., demonstrated the feasibility of achieving economically acceptable concentrate grade and recovery levels using large, high-capacity flotation cells. The composition of the feed to the Haynsworth beneficiation plant is a typical Florida pebble phosphate matrix composed of phosphorite pebbles ranging in size from approximately 1-1/2 in. down to 150 mesh and intimately associated with a mixture of clay and sand (essentially silica). The feed contains approximately 22 to 28% phosphate reporting as tricalcium phosphate, Ca3 (PO,) 2, or "bone phosphate of lime" (BPL). The flotation section utilizes the double-float procedure typical of Florida plants. The phosphate is first floated away from the silica in the rougher circuit, using crude fatty acid, ammonia, and fuel oil or kerosene. Rougher conditioning is accomplished at 60 to 70% pulp solids with sufficient ammonia added to raise the pH to 9 to 9.5. Following coarse and fine rougher flotation, the concentrate (overflow) streams are joined and conditioned (sulfuric acid cleaned and washed) prior to entering the cleaner circuit where an amine float (cationic reagent and kerosene added in the feed box; pH 7.3 to 7.8) is employed to float the silica. The feed to the coarse rougher circuit averages 29% +35 mesh while the fine rougher feed averages 10%+35 mesh. Primary attention was directed toward the large rougher cell performance (recovery and grade) on coarse feed during the Haynsworth evaluation program. Flotation Cell Test Program A row of three No. 120 size (300 cu ft) WEMCO flotation cells was installed in parallel with an existing air-cell row. The total installed volume of the large cell circuit was 900 cu ft and required a floor space of 306 sq ft. This compared to the air-cell total volume of 200 cu ft and 152 sq ft floor space. (Both floor areas include feed and tails hoppers but exclude walkways.) Fig. 1 is a schematic cross section of the large flotation cell showing the relative location of key mechanism elements. In operation, the rotor generates a fluid vortex extending up along the walls of the standpipe and creating a sufficient vacuum within its core to ingest air into the standpipe/rotor cavity through the air inlet duct. The ingested air mixes with the pulp, which has been recirculated through the false bottom and draft tube, in the rotor. Further mixing occurs as the air and pulp move radially outward from the rotor, finally passing through the disperser into the flotation cell. Flotation is accomplished outside the disperser, where phosphorite laden air bubbles rise and the remaining pulp recirculates down along the cell wall to the false bottom and draft tube. Large-flotation-cell performance is influenced by the ability of the mechanism to (1) circulate, or suspend, the solids in the pulp; (2) ingest air into the rotor cavity; and (3) mix the air and pulp effectively. The proper balance between pulp circulation and air ingestion is a key consideration in achieving good recovery in a course feed application. Large-flotation-cell pulp circulation and air transfer characteristics are significantly influenced by rotor speed and rotor submergence; therefore, these two operational parameters can be used to "optimize" a particular mill application. Fig. 2 maps the hydraulic performance of the WEMCO No. 120 size flotation cell. This map can be used to relate the cell operational parameters which influence metallurgical performance. At a given rotor speed, power intensity (i.e., pulp circulation) is seen to increase, and airflow decrease, as rotor submergence is increased. The inverse relation between power and airflow is due to the two-phase air-liquid mixture density reduction accompanying the increased airflow rate. For any fixed rotor submergence, the power intensity (i.e., fluid circulation) and airflow both increase as rotor speed is increased. The selection of these two mutually related operating conditions (i.e., rotor speed and submergence) was a key consideration in the Haynsworth evaluation program.

Jan 1, 1976

By F. Wald, A. J. Rosenberg

The general features of the constitution of the B-Pt system were determined using standard rnetal-lograph~c, thermoanalytic, and X-ray diffraction techniques. Three compound were found. Two of these, Pt3B and Pt,B, are formed by peritectic reactions at 523° and 890°C, respectively. The third, Pt3B,, is congruently melting with a flat maximum at 940°C but decomposes eutectoidally in to Pt,B ant1 boron nt - 600° to 650°C. THE low-temperature allomorph of boron (red, simple rhombohedra1 a boron) is of scientific and technological interest as an elemental semiconductor.' However, the studies of this material have been hampered by its reported instability above 1200"~ which precludes crystal growth from the melt (mp - 2200°C). Crystallization from platinum solutions has been suggested as an alternative crystal-growth technique, but has met with only limited success.' The technique depends upon the existence of a significant difference between the eutectic temperature and the transformation temperature of boron. In order to clarify the conditions for further crystal-growth experiments, we found it desirable to redetermine the main features of the B-Pt phase diagram since previous reports on the system1'5'6'7 are in marked disagreement. EXPERIMENTAL The experimental methods used were thermal analysis, metallography, X-ray analysis, and, to a lesser extent, measurements of microhardness. Most of the alloys were prepared from spectrograph-ically standardized boron obtained from Johnson-Matthey &Co., Ltd. (212 ppm impurities, exclusive of carbon and oxygen) and platinum powder obtained from F. Bishop & Co. (200 ppm impurities, mainly of other platinum group metals). Some alloys were also prepared with very high-purity, float-zone refined boron (99.9999 pct obtained from "Wacker Chemie" and extrahigh-purity platinum (99.999 pct) obtained from Johnson-Matthey & Co., Ltd. The reported results did not depend on the choices of these starting materials. Five-gram alloy specimens containing 10, 20, 25, 27.5, 30, 33.3, 34, 35, 37, 37.5, 38, 39, 40, 41, 42, 43, 45, 50, 55, 60, 70, and 80 at. pct B were made by melting the elements together in boron nitride crucibles using rf heating of a graphite susceptor, either in vacuum or under high-purity argon. All alloys were heated to at least 1800°C for -5 to 15 min. Most of the alloys did not wet the crucibles when the latter were outgassed by preheating under vacuum. In any event, no weight loss was detected after melting, and the nominal composition was assumed for all specimens. Thermal analysis on 2.5-g samples were carried out in boron-nitride crucibles under a vacuum of 5 x X torr. The apparatus was heated in a "Kan-thal A 1" wound furnace, which limited the maximum temperature to about 1100°C. The output of the indicator thermocouple was fed to a dc recorder with a 1-mv full-scale span and an adjustable zero. The apparatus was calibrated repeatedly, using the freezing points of high-purity aluminum, silver, and gold. The results justified the use of the NBS voltage vs temperature tables for Pt/Pt 10 pct Rh thermocouples. All thermal analyses were run at least twice and both the heating and cooling effects were recorded. Most of the alloys had a very strong tendency to supercool. However, the use of mechanical vibration permitted reproducibility within *5°C for all alloys, except in the region around 40 at. pct B. Only the cooling effects are plotted in Fig. 2, since they appear to be more reliable. For metallography, the alloys were cut with a diamond cutting wheel, cast in a polymethacrylate resin, ground and polished with diamond paste, and etched with dilute aqua regia, a common etch for platinum alloys. Both copper and molybdenum radiation were employed to obtain X-ray diffraction data using Debye-Scherrer cameras and a "Norelco" diffractometer Diffractometry with high scanning speeds (1 deg per min) using nickel filtered CuK, radiation was used to identify the main regions of the diagram. However, molybdenum radiation was used for the detection of boron, since the latter showed very strong absorption and fluorescence effects with CuK, radiation. RESULTS AND DISCUSSION Three intermediate compounds, corresponding to the compositions Pt3B, Pt2B, and Pt3B2, were found in the system. Fig. 1 reproduces their X-ray diffraction spectra, together with those of pure boron and pure platinum. As can be seen from the thermal-analysis data in Fig. 2, Pt3B and Pt2B are formed by

Jan 1, 1965

By H. E. Kramm

During the summer of 1910, I had the opportunity to study in detail the geological conditions of what is known in northern California as " Harrison gulch," in Shasta county. Though the district, as a whole, that is, the western part of Shasta and the eastern part of Trinity county, has contributed during the last 15 years a considerable share of the gold-production credited to Shasta county, very little is known of its geology, perhaps because the country is covered with a dense growth of brush which makes exploration and prospecting extremely difficult. Topographically the district presents a succession of ridges trending approximately N-S., and alternating with deep, narrow canyons. The drainage is partly into the Sacramento, partly into the Trinity river. Climatic conditions in summer time are almost ideal. It is true, the thermometer may climb to 115°, but the air is dry

Jan 1, 1913

By P. C. Claspy, P. H. Smakula

The electro-optic coefficients of LiNbO, and KTao.,5Nboe3,O3 (KTN) have been experimentally determined at the HeNe laser wavelengths of 0.6328, 1.15, and 3.39 µ. The coefficients were calculated fronz the retardation induced by an applied electric field. The retardations were measured by observing one or move transmission maxima and minima as a function of the applied field, and by measuring the retardation directly with a Babinet-Soleil compensator. The values obtained agree quite well with those previo~lsly reported by others. Extinction ratios as high as 3000:l have been observed. Resistivities and Curie temperatures have also been measured. Light-induced optical inhornogeneities in LiNbO, repovted by others have been observed. CONSIDERABLE interest has recently been shown in the electro-optic properties of LiNb03 (Refs. 1 and 2) and KTN.3, 4 These crystals have a number of advantages over such well-known materials as KDP. These advantages include: 1) the infrared transmission of KTN and LiNb03 extends to 5 p whereas that of KDP cuts off at 1.5 p ; 2) driving voltages required for modulators using these materials are considerably lower than those required for KDP. After first discussing some theoretical considerations of the electro-optic effect, we will report the results of measurements of the dc electro-optic coefficients of these materials at wavelengths of 0.6328, 1.15, and 3.39 p. THEORY The generalized equation for the electro-optic effect can be written: Although lattice polarization is the fundamental variable, rather than the applied electric field, we follow the convention of expressing the linear electro-optic effect in terms of the applied field. For LiNbO the quadratic terms are negligible. Since KTN has a center of symmetry the rijk tensor is 0. After applying the usual symmetry considerations and index contractions,* the rijk and gijkl tensors can be expressed as follows: LiNbOaT If field directions are now chosen, the change in refractive index and the angle between the induced optic axes and the crystallographic axes can be found. The induced rotations of the principal axes of the index ellipsoid for fields in principal crystallographic directions are given in Table I. Since KTN is initially isotropic, the principal axes in the zero-field condition are parallel to the crystallographic axes. The induced retardations are given in Table 11. EXPERIMENTAL We obtained the various electro-optic coefficients by measuring the induced retardation as a function of

Jan 1, 1968

By Erhard Hornbogen

Twins were propagated into large, well-annealed crystals of a, iron-phosphorous and a, iron-molybdenum solid solutions. Strain fields caused by interaction of these twins were made visible by precipitation. These strain fields can be explained by assuming that transmitted and reflected plastic waves are created when a twin strikes an obstacle with high velocity. The twin front itself can be regarded as a shear wave that may be able to develop a one-dimensional shock front. The occurrence of {WO} fracture by the reflected stress is also discussed. The described effects were not found when twins propagated at lout velocity into disturbed crystals, for example, into crystals previously deformed by slip. DEFORMATION twinning leads to shearing of a crystal lattice under external load. The shear appears to be homogeneous over a large number of crystal layers. In a iron, shear occurs on the (112) planes and in the <1ll> directions. The formation of a twin proceeds by the movement of partial dislocations that change the stacking at the twinning plane.l, In the bcc lattice, this partial dislocation can be created by dissociation of a sessile a/2[111] dislocation that lies in the (112) plane: Cottrell and Bilby&apos;s spiral mechanism can explain the homogeneous shear, but has not been proven experimentally. Nevertheless, this mechanism can explain the possible high velocity of formation of a twin. In Cottrell and Bilby&apos;s model, as in other models of twinning or phase transformation, a much higher energy is required to spread the first stacking fault than to add new layers by further movement of the partial dislocations. The dislocations will therefore become accelerated proportional to the difference between the stress, tN, to nucleate and tp to propagate the twin. It has been assumed3,4 that tn is the stress required to make two partial dislocations of apposite sign pass for the first time. After the first layer of new stacking has been formed, the maximum stress is TN=Gb/4pd where G is the shear modulus, b is the Burgers vector of the partial dislocation, and d is their perpendicular spacing so that the amount of shear is S = b/d. From this formula, a value of 25 kg per mm2 has been estimated for twinning in Zn3. The measured values are smaller, but local internal stresses may help to provide the necessary stress. For a iron, a higher value can be expected, mainly due to the higher value of G. That agrees with the observation that "burst" twinning occurs if the yield strength is in-

Jan 1, 1962

By R. Maddin, S. K. Tung

SUCCESS of the dislocation theory in formulating the transitional lattice theory proposed by Har-greaves and Hill in 1929&apos; is well established for low angle grain boundaries. The theoretical work of Burgersa and Read and Shockley,3 together with the experimental observations of Aust and Chalmers4 and Parker and colleagues,6 leaves little doubt as to the structure of grain boundaries with differences of orientations up to between 15" and 20". Beyond these angles, the structure of the boundary is not so clear, and is still a matter for conjecture. There have been notable experiments devised from which the data could be used to calculate energetics for possible arrangements of atoms in forming a large angle boundary.6 Most of these experiments deal with diffusion through and along the grain boundary. The recent work of Rhines and Cochart7 and Rhines, Bond, and Kissel18 was concerned with the relative movement of grains in aluminum bicrystals under constant tensile loads with their boundaries aligned at 45 " to the tension axis. The gliding along the grain boundary was cyclic and began after an incubation period. The velocity of gliding increased with the sum of the angular difference, 8, between the operative slip direction in the conjugate crystals and the angular difference between the active slip planes as measured between their traces upon the grain boundary. The initial gliding rate varied with temperature, and the logarithm of the average gliding taken over a considerable period was a linear function of the reciprocal of the absolute temperature: the slope gave an activation energy of 11,000 ±1,000 cal per mole. Since the rate of grain boundary shear is sensitive to the misorientation of the grains themselves, as shown by several workers,7,8 it is suggested that further work of this type might be fruitful in adding information regarding the behavior of boundaries under stress. The techniques devised by Chalmers" added impetus to the facility for observing grain boundary behavior, in that they provided a simple means for producing bicrystals of predetermined orientation so that the angle of the boundary could be controlled,

Jan 1, 1958

By R. F. Mehl, G. V. Smith

THE decomposition of austenite in steels, because of its immense practical importance, has been subjected to extensive study in recent years from the point of view of the mechanism of the process.1-3 Although much information has been acquired, a number of questions, principally of theoretical interest, remain. One is that of the atomic-crystallographic mechanism by which each of the various reaction products forms. The isothermal reaction products of the eutectoid decomposition in plain carbon steels (to which this study is restricted) have conveniently been classified in three general groupings-pearlite, bainite, and martensite. Of these several products, pearlite and martensite have been studied extensively, but bainite has received only scant attention. As a result, the mechanism of the formation of pearlite and that of martensite are now fairly well understood while a great deal of uncertainty exists regarding bainite. PEARLITE Pearlite forms from austenite by the precipitation of alternate platelets of cementite and ferrite, which grow into the austenite matrix .2-5 The rate of reaction may be described in terms of a rate of nucleation and a rate of growth.2.3 Mehl and Smith6 have attempted to determine the lattice relationships existing between the ferrite in pearlite and the parent austenite. Using a pole-figure method of analysis, it was found that a limited number of ferrite orientations resulted from the decomposition of a single grain of austenite; it was not possible, however, to decide between two assumed ideal relationships, both of which appeared to account for the experimentally determined pole figure. It was definitely shown, however, that the relationship obtaining was quite different from that determined for the proeutectoid separation of ferrite.7 No attempt was made to determine the habit plane (matrix plane to which the precipitate lies parallel) of the pearlite lamellae. Belaiew8 earlier had stated that the number of directions assumed by the pearlite lamellae in a single grain of austenite was 12 (no details were given) and concluded wrongly, as Mehl and Smiths have pointed out, that the lamellae delineate the [210] planes of ferrite.* MARTENSITE It is known that martensite is a transitional constituent of body-centered tetrag-

Jan 1, 1942

By C. H. Hewitt, J. T. Morgan

The Fry cocurrent in situ combustion project was carried out in a 3.3-acre portion of a lenticular body of Robinson sandstone of Lower Pennsylvanian age. This particular sand body is about 12,000 ft long and 3,500 ft wide; it varies in thickness from 0 to 55 ft, trends northeast-southwest, and occurs at depths between 880 and 936 ft. The reservoir is made lip of three distinct types of sandstone, each having characteristic reservoir properties. (See Table I.) Textural gradients, sedimentary structures, erosional basal contact, absence of marine fossils, and geometry of the sand body all indicate that the sandstone is of fluvial origin and part of an extensive complex of river-deposited sedirnents. Geographically oriented cores reveal that the direction of depositing currents was to the southwest, parallel with the sand-body trend. Directions of maximum pernleability also parallel the northeast-southwest trend. The layered nature of the sandstone reservoir and its directional properties have controlled the areal distribution of produced gas, the ignition behavior, and the vertical profile and horizontal extent of the conbustion zone. INTRODUCTION This paper is the first of a series of three papers that describe Marathon Oil Co.&apos;s Fry in situ combustion test. This first paper contains the results of a detailed study of the geology and reservoir characteristics of the Robinson sandstone reservoir in which the Fry test was conducted. The second and third parts of this series report on the field operations&apos; and performance. The geologic work reiated to cores cut through the combustion zone, and to the effect of reservoir properties on the combustion process is included in the third paper.&apos; GEOLOGIC STUDY OF THE FRY RESERVOIR The close spacing of continuous cores in the Fry combustion site provided an unusual opportunity to study the details of distribution of lithology and reservoir properties within a petroleum reservoir. The objectives of the study were: 1. To determine the distribution of rock types within the Robinson sandstone in the Fry area; 2. To determine the relationship of porosity and permeability to rock properties and establish the distribution and homogeneity of reservoir properties; 3. To determine the origin of the Robinson reservoirs so that attempts could be made to predict the size, shape, distribution, extent and continuity of Robinson reservoirs; and 4. To determine what effects, if any, the reservoir rocks might have on the combustion process, so that the process might be better evaluated. AVAILABLE MATERIALS Continuous cores were cut from 14 wells in the vicinity of the Fry site. Ten of the cores are from within the 3.3-acre pattern; six of the 10 were cut prior to combustion, and four were cut through the combustion zone. Cores from the Emma Fry No. 15, Wampler 0-2 and Fry B wells (Figs. 1, 2 and 9) were geographically oriented by the Eastman Oil Well Survey Co. Maps, electric

Jan 1, 1966

By Michael J. Messel

THE critical shortage of asbestos fiber in the world today brings to the foreground the question of locating and developing new deposits. The object of this paper is to discuss some of the more important factors which should be considered in the examination and valuation of a new asbestos enterprise. Some of the more important uses of asbestos fiber are for textiles, heat insulators, building materials, filters and a series of other uses. The properties of this mineral, such as fibrous structure, color, strength, silkiness and flexibility, coupled with resistance to fire, certain chemical action and decay make its application unique for certain industrial uses which consume over 500,000 tons annually. These same unique properties which make this mineral so valuable also make a deposit one of the most difficult to appraise accurately, because of the many undeterminable and varying factors which must be considered before a deposit can properly be termed commercial. The majority of the asbestos fiber today, having the above mentioned properties, is sold by grades which are based on fiber length. Present day fiber prices vary over a wide range from $800 to $225 for crude fibers and $300 to $20.00 per ton for milled grades. For valuation purposes a careful study should be made of existing fiber prices and markets. EXAMINATION OF DEPOSITS In carrying out prospecting and examination of a deposit, considerable caution is required to get the necessary information in the form that will have the most value for the final determination. There are two main classes of asbestos fibers, chrysotile and the amphiboles, the chrysotile being, by far, the most important both in abundance and uses. This paper will stress mainly chrysotile deposits, however, the amphiboles have many important uses, especially amosite and crocidalite. Their valuation presents special problems as other factors may be involved, especially as they are not graded according to any well defined and adopted standard but usually according to the use for which they are being supplied. Most chrysotile deposits occur in two main types of rock, (I) mainly in basic igneous, such as dunite and peridotite, (2) to a lesser extent in sedimentary rocks, such as dolomite and limestone. All of these require a certain degree of metamorphism to be favorable to asbestos formation. Approximately 90 pct of the asbestos deposits are derived from serpentinization of dunite or peridotite, whereby the magnesiumsilicate olivine was altered to hydrous magnesium-silicate serpentine. Under certain favorable geological conditions, this serpentine takes a fibrous form having a definite crystal structure, probably due to molecular rearrangement, and is known as chrysotile. The fiber veins are usually ir-

Jan 1, 1947

By HUBERT O. De

IN December, 1936, several drilling tests were made at the Hubert O. De Beck feldspar mine at Green Mountain, N. C., to determine the most efficient type of hammier-drill bit and drilling method for use at this particular property. This mine is well recognized as having the hardest rock in the Burnsville - Spruce Pine feldspar district and drilling costs always have been high. Local structural deformation has greatly distorted and warped the normal crystalline structure of the feldspar so the rock is much tougher than usual. In studying drilling methods and bit types, available literature was re¬viewed but little specific data could be found on the direct comparison of four-point and six-point drill bits so the following results may be of some interest.

Jan 1, 1937

By Ben. B. Cox

The principal events during the year consisted in the exploitation of the Kirkuk field, the regular operation of the four-million-ton pipe line to the Mediterranean, and the discovery of low-gravity oil on three other structures in the West Tigris (Shergat) area. The Iraq Petroleum Co., Ltd. continued the systematic exploitation and exploration of its Kirkuk field, maintaining a carefully unitized operation. Bottom-hole pressure differentials and low gas-oil ratios were maintained. All crude was produced by flowing The cleaning up following the construction of the Mediterranean pipe line, which began deliveries in August, 1934, was completed during the first quarter of 1935. The line easily maintained its rated capacity for the remainder of the year. The Mosul Oilfields, Ltd., through its operating subsidiary, the B.O.D., Ltd., expanded its exploratory organization from 9 to 16 drilling rigs and discovercd 20" A.P.I. crude on the Sadid, Hibbarah and Qasab anticlines. Whether these discoveries will be commercial pools remains to be proved. The Qaiyarah-Najmah-Jawan field, which was discovered by the I.P.C. in 1928, was extended arid production was found in the Eo-Cretaceous as well as the "Main Limestone" (Eocene, Oligocene and Lower Miocene). Gas caps were found under each of the crests of the West Tigris structures. Negotiations are in progress between the Mosul Oilfields, Ltd. and the Iraq Government for the extension of the Anatolian Railway from the Turkish border to Mosul, with a view to tanking the heavy West Tigris crude to the Mediterranean. The subsidiary of the Anglo-Iranian Oil Co., Ltd.&apos;, the Khanaqin Oil Co., Ltd., continued to operate its Naft Khaneh field near the Iranian (Persian) border to supply the local Iraq market through the Rafidain Oil Co., Ltd. Somewhat more than 28 million barrels of crude was produced in Iraq during 1935. Crude delivcred to the pipe line for export during the years 1934 and 1935 was: Year BaRrels 1934................................................. 7,096,669 1935................................................. 27,014,904 Total as at Dec. 31, 193.5.............................. 34,111,573 ° Converted at an avcrage of 7.0 bbl. per ton.

Jan 1, 1936

By Eckley B. Coxe

IN the anthracite coal regions of Pennsylvania the custom has been to sight either at an open light (generally a mine-lamp), or at the string of a plumb-bob. If the station was intended to be a permanent one, a spud, as it is called, that is, a nail resembling a horseshoe nail with a hole in the head, is driven into the timbers over the station, or, if there be no timber, a hole is drilled in the coal or rock roof, into which a wooden plug is driven, which serves to hold the spud. The first operation in making a survey is to lay out the stations, that is, to mark the place where the holes are to be drilled for the plugs or the points on the timbers where the spuds are to be driven in. This should be done before any instrumental work is begun, as much labor can generally be spared, and the use of very short sights can often be avoided, by carefully laying out the stations beforehand. When the stations were laid out, a plumb-bob was hung from the innermost spud, which I will call No. 1, the instrument was put in position at No. 2, by plumbing down and putting a centre-pin under the spud, and then setting up over the centre-pin, and another plumb-bob was suspended from No. 3. If great accuracy was not required, a mine-lamp was set up under the plumb-bobs, at No. 1 and No. 3, and the engineer sighted at them. If great accuracy was required, a lamp or some white surface was held by an assistant behind the strings of the plumb-bobs. To work with any speed by the latter method (i. e., the accurate one), it was necessary for the engineer to have three assistants on whom he could rely even when the chaining was done afterwards; viz.: one to hold the light behind the string at No. 1, one at No. 3, and an assistant at the instrument to hold the light while levelling, reading the in-

Jan 1, 1873

The principal events during the year consisted in the exploitation of the Kirkuk field, the regular operation of the four-million-ton pipe line to the Mediterranean, and the discovery of low-gravity oil on three other structures in the West Tigris (Shergat) area. The Iraq Petroleum Co., Ltd. continued the systematic exploitation and exploration of its Kirkuk field, maintaining a carefully unitized operation. Bottom-hole pressure differentials and low gas-oil ratios were maintained. All crude was produced by flowing The cleaning up following the construction of the Mediterranean pipe line, which began deliveries in August, 1934, was completed during the first quarter of 1935. The line easily maintained its rated capacity for the remainder of the year. The Mosul Oilfields, Ltd., through its operating subsidiary, the B.O.D., Ltd., expanded its exploratory organization from 9 to 16 drilling rigs and discovercd 20" A.P.I. crude on the Sadid, Hibbarah and Qasab anticlines. Whether these discoveries will be commercial pools remains to be proved. The Qaiyarah-Najmah-Jawan field, which was discovered by the I.P.C. in 1928, was extended arid production was found in the Eo-Cretaceous as well as the "Main Limestone" (Eocene, Oligocene and Lower Miocene). Gas caps were found under each of the crests of the West Tigris structures. Negotiations are in progress between the Mosul Oilfields, Ltd. and the Iraq Government for the extension of the Anatolian Railway from the Turkish border to Mosul, with a view to tanking the heavy West Tigris crude to the Mediterranean. The subsidiary of the Anglo-Iranian Oil Co., Ltd.&apos;, the Khanaqin Oil Co., Ltd., continued to operate its Naft Khaneh field near the Iranian (Persian) border to supply the local Iraq market through the Rafidain Oil Co., Ltd. Somewhat more than 28 million barrels of crude was produced in Iraq during 1935. Crude delivcred to the pipe line for export during the years 1934 and 1935 was: Year BaRrels 1934................................................. 7,096,669 1935................................................. 27,014,904 Total as at Dec. 31, 193.5.............................. 34,111,573 ° Converted at an avcrage of 7.0 bbl. per ton.

Jan 1, 1936

By R. F. Mehl, G. V. Smith

THE decomposition of austenite in steels, because of its immense practical importance, has been subjected to extensive study in recent years from the point of view of the mechanism of the process.1-3 Although much information has been acquired a number of questions, principally of theoretical interest, remain. One is that of the atomic-crystallographic mechanism by which each of the various reaction products forms. The isothermal reaction products of the eutectoid decomposition in plain carbon steels (to which this study is restricted) have conveniently been classified in three general groupings-pearlite, bainite, and martensite. Of these several products, pearlite and martensite have been studied extensively, but bainite has received only scant attention. As a result, the mechanism of the formation of pearlite and that of martensite are now fairly well understood while a great deal of uncertainty exists regarding bainite. PEARLITE Pearlite forms from austenite by the precipitation of alternate platelets of cementite and ferrite, which grow into the austenite matrix.2-5 The rate of reaction may be described in terms of a rate of nucleation and a rate of growth 2 3 Mehl and Smiths have attempted to determine the lattice relationships existing between the ferrite in pearlite and the parent austenite. Using a pole-figure method of analysis, it was found that a limited number of ferrite orientations resulted from the decomposition of a single grain of austenite; it was not possible,[ ]decide between two assumed ideal relationships, both of which appeared to account for the experimentally determined pole figure. It was definitely shown, however, that the relationship obtaining was quite different from that determined for the proeutectoid separation of ferrite.7 No attempt was made to determine the habit plane (matrix plane to which the precipitate lies parallel) of the pearlite lamellae. Belaiew8 earlier had stated that the number of directions assumed by the pearlite lamellae in a single grain of austenite was 12 (no details were given) and concluded wrongly, as Mehl and Smith&apos; have pointed out, that the lamellae delineate the {210} planes of ferrite.* MARTENSITE It is known that martensite is a transitional constituent of body-centered tetrag-

Jan 1, 1942

By John T. Galey

In southwestern Pennsylvania 151 wells1 were completed during 1938, a total of 61 less than the preceding year. Of this number 81 were gas wells and 28 oil wells, which shows a considerable decline from 1937, when 108 gas wells and 64 oil wells were completed. However, 42 dry holes were drilled during 1938, which is two more than the previous year. Shallow Development—Gas No new extensions to old pools, or new wells that would indicate any substantial reserves, mere found during the year. However, a number of commercial wells and many dry holes were drilled to the Big Injun sand in Menallen township, Fayette County. One well had an initial open flow of 6 million cu. ft. In Rich Hill township, Greene County, one well producing, from the Big Injun sand, 2 million cu. ft. was brought in. Several other gas wells were completed in Shaler township, Alleghany County and Center township, Greene County, both of which had initial open flows of 1 million cu. ft. from the 30-ft. sand. Another well, in Aleppo township, Greene County, had an equal volume from the Gordon Stray sand. Oil Development has proceeded at a retarded rate because of the low price of Pennsylvania-grade crude. A total initial of only 205 bbl., an average of 7.3 bbl. per well, was developed. This is 1785 bbl. less than during 1937 and no new repressuring operations have been contemplated to prevent the declining production. The average price received for oil was $1.56 per barrel, with a high of $1.88 and a low of $1.34. This oil costs $1.94 per barrel2 to produce. The average price paid for Bradford

Jan 1, 1939

By Charles P. Williams

BY PROFESSOR CHARLES P. WILLIAMS, ROLLA, MISSOURI. During the fall of the year 1873, attention was redirected to the occurrence of lead ores in Southwestern Arkansas (chiefly in Sevier County), and somewhat extensive explorations of the deposits have since been made in the hope of finding the ores sufficiently argentiferous to be profitably worked. How far the expectations have been realized I am not authentically advised, but samples of the galena ore, yielding 62.09 per cent. of lead, gave on assay at the rate of 15 3-10 ounces of silver to the ton of ore. This was the highest result obtained by myself, though I am informed that higher yields have been obtained by others. Among the samples of ores from this locality, forwarded to me in January last, was one specimen which I at once recognized as stibnite, and, on notification, other specimens of the same from Sevier County were forwarded me. The first specimen of the several received contained 11.51 per cent. of gangue, 57.62 per cent. antimony, 4.57 of bismuth, with small amounts of arsenic and iron. The latest result from a portion of another hand specimen I append in full, with duplicate estimations of the arsenic, bismuth, and gangue. The analyses were all conducted by Mr. C. R. Winters, under my direction, and in the case of those given below the ore mas separated as closely as possible from the gangue before analysis. The results are for the mineral freed from hygroscopic moisture, and are as follows: I. 11. Mean. Sulphur,.. 28.618 .. . 28.518 Antimony,.68.576 .. . 68.676 Arsenic,..6 47 .474 .497 Bismuth,..521 .498 .509 Iron,.......762 .. ..762 Gangue,..944 .948 .946 99.868 99.808 This result indicates that the ore is stibnite.

By John T. Galey

In southwestern Pennsylvania 151 wells1 were completed during 1938, a total of 61 less than the preceding year. Of this number 81 were gas wells and 28 oil wells, which shows a considerable decline from 1937, when 108 gas wells and 64 oil wells were completed. However, 42 dry holes were drilled during 1938, which is two more than the previous year. Shallow Development—Gas No new extensions to old pools, or new wells that would indicate any substantial reserves, mere found during the year. However, a number of commercial wells and many dry holes were drilled to the Big Injun sand in Menallen township, Fayette County. One well had an initial open flow of 6 million cu. ft. In Rich Hill township, Greene County, one well producing, from the Big Injun sand, 2 million cu. ft. was brought in. Several other gas wells were completed in Shaler township, Alleghany County and Center township, Greene County, both of which had initial open flows of 1 million cu. ft. from the 30-ft. sand. Another well, in Aleppo township, Greene County, had an equal volume from the Gordon Stray sand. Oil Development has proceeded at a retarded rate because of the low price of Pennsylvania-grade crude. A total initial of only 205 bbl., an average of 7.3 bbl. per well, was developed. This is 1785 bbl. less than during 1937 and no new repressuring operations have been contemplated to prevent the declining production. The average price received for oil was $1.56 per barrel, with a high of $1.88 and a low of $1.34. This oil costs $1.94 per barrel2 to produce. The average price paid for Bradford

Jan 1, 1939