Search Documents

By Martin Rubenstein

CdS crystals have been grown from a number of metallic solvents such as bismuth, tin, lead, and cadmium. Etching studies have shown that plastic deformation occurs if the crystals are not removed from the solvent prior to the solidification of the solvent, on cooling. The deformed crystals show a umique exciton fluorescence as a function of edge dislocation density. If one grows the CdS in the eutectic alloy of the above four metals (commonly called Wood's metal) the crystals can be removed from the solvent with hot water and no plastic deformation occurs. In this paper, the liquidus solubility measurements of CdS, as a function of temperature, are presented. The data were obtained using a high -temperature filtration technique. CADMIUM-SULFIDE crystals have been grown from a number of metallic solvents1 such as cadmium, bismuth, tin, and lead. Liquidus solubilities of CdS in cadmium,2 bismuth,3 and tin4 have already been measured. Crystals of CdS, in all four metals, have been grown by solution growth: 1) by cooling a saturated solution and 2) by a solution transport method.1'"1 CdS crystals grown in these four solvents have a few characteristics in common: 1) 1.8°K photolumines-cent emission consisted mainly of the radiative recombination of the bound exciton commonly known as I,, 2) slip lines which could easily be seen by the naked eye, and 3) edge dislocation densities in the order of l05 per cu cm.1 It was decided that these slip lines and the high edge dislocation densities were caused by a plastic deformation of the CdS crystals. It was felt that this plastic deformation did not occur during the growth of the crystals nor during the cooling of the solution, but did occur when the solvent which was in contact with the crystals froze. If these assumptions were valid, the slip lines and the high number of dislocations could be reduced or eliminated by removing the crystals from the solvent before the solvent froze. Since crystals of CdS had already been grown separately in such solvents as bismuth, lead, tin, and cadmium, it was felt that crystals could be grown in a eutectic mixture of these four metals. In this work a eutectic (or near eutectic) mixture of bismuth, lead, tin and cadmium in the proportion 50, 26.5, 13.5, and 10 wt pct, respectively, was used to grow CdS crystals. Such a mixture has a melting point of about 70°C and is close in composition to the alloy commonly known as Wood's metals. If the crystals could be grown from this mixture of solvents, and if hot water (>75°C) could be used to separate the crystals of CdS from the metallic solvent, it was hoped that CdS crystals could be grown with little or no plastic deformation which had been ob- served when crystals were grown from these solvents uncombined. CdS crystals were grown from this low melting eutectic mixture of bismuth, lead, tin, and cadmium using the solvent transport method. CdS powder and the appropriate amount of metals were sealed in a quartz tube under a pressure of about 5 X 10-6 torr. This ampule was then placed in a vertical position in a furnace. The temperature was raised to about 900°C. The furnace was designed so that the top of the liquid column within the ampule was between 10° to 40°C higher than the bottom of the liquid column. These temperatures were measured on the outside of the quartz ampule. The ampule was maintained at temperature for 7 to 14 days (depending on the temperature at which transport was taking place) and then the furnace temperature was lowered until the temperature was about 125°C. The ampule was then removed from the furnace, placed in water maintained at about 90°C, and opened in this 90°C environment. The crystals could then be removed from this two-phase liquid (Wood's metal and water) by mechanically picking them out. Alternatively, the crystals could be quantitatively removed by adding an excess of mercury to the mixture of metals, crystals, and hot water. The hot solution of metals and the hot water could be evacuated using a small diameter tube connected to a vacuum. Small amounts of mercury and water could be removed by heating the crystals in vacuum. Crystals prepared using this technique showed no evidence of slip. However, some of these crystals did show edge dislocation densities as high as l04 per cu cm. Some few selected crystals showed no dislocations. Single crystals of CdS were grown as large as 5 by 5 by 0.5 mm. The ampules for the growth of these crystals were 13 mm O.D., 11 mm I.D., 150 mm! LIQUIDUS SOLUBILITY MEASUREMENTS The CdS starting materials was G.E. 118-8-2 powder which was fired in H2S at 1000°C, and then a vapor transport technique5 was applied to produce a "sound" mass of CdS. The Wood's metal was prepared by weighing out bismuth, lead, tin, and cadmium in the proportions of 50, 26.5, 13.5, and 10 wt pct, respectively. The bismuth, cadmium, and lead were from the American Smelting and Refining Co. (ASARCO) and all had purities of 99.999+ pct. The tin was 99.9999 pct spectroscopic grade from the Vulcan Materials Co. The appropriate mixture was placed in a quartz tube, evacuated to a pressure of 5 X 10-6 torr, melted to a liquid, cooled to room temperature under this same vacuum. This ingot was then placed in another quartz tube, evacuated to 5 x l0-6 torr, and sealed off under vacuum. The ampule was then horizontally placed in a furnace. The temperature was raised to 600°C, and over a period of several hours the ampule was vigorously shaken several times. The ampule was then removed from the furnace, and the metallic liquid was

Jan 1, 1970

By S. R. Balajee, I. Iwasaki

The adsorption mechanism of corn starch and its derivatives at mineral-solution interfaces was investigated by the adsorption of cationic starch, unmodified corn starch, British Gum 9084, and anionic starch on quartz and hematite. The adsorption of these starches, which decreases in the order mentioned, is dependent on the balance between the magnitude of the electrostatic interaction and the magnitude of the hydrogen bonding. There exists a critical starch concentration for both optimum flotation and flocculation conditions of iron ores, which corresponds to a point where the starch adsorption reaches a saturation coverage. Flocculation occurs due to the adsorption of starch via electrostatic and hydrogen-bonding forces and by interparticle bridging as a result of the conformation of starch molecules at the interface. The depressant property of starches and starch derivatives in flotation' and their flocculation char: acteristics in clarification and filtration2.3 have long been recognized on a wide variety of ores. The effectiveness of a starch as a depressant for iron minerals has been the subject of much investigation in recent years both in the amine flotation of siliceous gangue and in the anionic flotation of activated silica from iron ores. It has been reported that the depressant activity of starches and dextrins in the cationic flotation of quartz from hematite increases with molecular weight, branching, and number of hydroxyl groups, 1 and that the selectivity is affected by changing the configuration of starch molecules and the composition of its polar groups.4 ,5 The manner in which starches are solubilized was shown to exert a significant influence as a depressant in the anionic silica flotation, and a series of articles covering the practical aspects of flotation and flocculation have already been reported.618 Chemical modification of the starch structure, the pulp pH, the calcium ion, and the residual starch concentration were identified as some of the more important variables affecting the flotation behavior. In the flocculation of iron ores, it was noted that most starches flocculated suspensions of hematite in water but did not flocculate similar suspensions of quartz,9 and that an excessive use of starch restabilized the suspensions due presumably to protective action. 6 An admirable application of such an observation to practice may be cited in the selective flocculation and desliming in the anionic silica flotation of iron ores, which resulted in superior metallurgy and lower reagent cost. 10 From detailed adsorption measurements, Schulz'and Cooke4 established that the adsorption of starches and their derivatives depended on the types of minerals and of starches, pH, and electrolytes present. Their adsorption data and the foregoing flotation and flocculation observations suggested that an electrical interaction between starches and charged mineral surfaces might be playing a role in their adsorption process. Adsorption of organic polymers, particularly of synthetic origin, at solid-liquid interfaces has been extensively studied in recent years,' and it is realized that their adsorption mechanism is considerably more complex than that of simple ions or molecules. A polymer molecule possesses a number of functional groups, and the adsorption at a point may restrict the adsorbability of adjacent groups. The mechanism may be further complicated by the conformation of the polymer molecules which may exist as coiled spheres, helices, or extended chains as a result of intramolecular interactions among functional groups as well as intermolecular interactions with solvent molecules. The object of the present investigation was to examine the effect of the chemical modification on the adsorption characteristics of starches and starch products on quartz and hematite at several pH values, so that by correlating this information with flocculation and flotation results, adsorption mechanism of starches on mineral-solution interface may be elucidated. EXPERIMENTAL MATERIALS Quartz: St. Peter sand was screened at 35 mesh and the undersize was scrubbed and deslimed at a Fagergren cell. The deslimed sand was cleaned with 0.1 N hot hydrochloric acid and washed repeatedly with distilled water, For anuscript, measurementsl the -200-mesh fraction of the sand was ground dry in a porcelain mill for 3 hr. The specific surface of the finely ground quartz was

Jan 1, 1970

By K. E. Manchester, A. H. Clark

Hall measurements have been made on three groups of silicon samples, which were implanted with boron, aluininunz, and phosphorus ions. Boron and phosphorus implants show essentially bulk properties when annealed under previously determined conditions, i.e., 15 min at 80O°C for boron and 10 mirz at 600°C for phosphorus. Bulk properties were also observed in alu?rrilzum-implanted samples when ion concentrations were below 1015 cm-'; however, strange low- terrzperalure behavior and a falloff in cavrier concenlralion was observed for sarnples with ion concenlration abozle loL5 ern-'. This can be attributed to solid-solubility effects since the average bulk concentration f0.r the sample exhibiting bulk properties was below the reported solubility limit for aluminum, while the other samples were above the limit. A detailed study of the annealirzg process indicates that mobilities reach bulk c~alues in phosphorus implants at 250DC, in alutninurn ivnplanls a1 500°C, and in boron implants at 700°C. A simple rnodel has been proposed to fit the annealing data. THE technique of semiconductor doping by direct injection of energetic ions is being actively investigated at this Center. Previously published results from this laboratory have been concerned with the investigation of implanted profiles in silicon and the electrical properties of the resultant p-n structures.1'2 Diode properties have been reported for junctions produced by implantation of boron ions and aluminum ions in n-type silicon and phosphorus ions in p-type silicon. Reverse current characteristics, as well as electron diffraction data, have indicated that the damage to the structure produced by the energetic ions during the stopping process can be minimized by a gentle anneal. The time-temperature conditions for this process have been determined by sheet resistivity studies.3 Electrical profiles of implanted phosphorus ions which have been determined by a differential sheet conductivity technique are based on the assumption that the carrier mobilities and activation energies for ionization are the same as in bulk silicon. These assumptions have been substantiated experimentally by measurement of Hall constants and resistivities of these implanted structures and the results are presented herein. After establishing the bulk property equivalence of the annealed layers, a more detailed examination of the annealing process was undertaken. The sheet resistivity technique initially used to determine anneal conditions has been broadened to include Hall constants and mobility behavior with anneal conditions. PROCEDURE The three groups of samples prepared for Hall measurements were implanted with mass-separated beams of boron, aluminum, and phosphorus ions. Ion concentrations are equivalent surface concentration and they have been determined from beam current measurements during implantation. Implant conditions for the samples are shown in Table I. In all cases, the samples had previously been angle-lapped on one edge and the junction delineated with an HF-copper sulfate solution. The surfaces of the implanted regions of the samples were exposed to the delineating solution and in the case of the "n"-type phosphorus-implanted areas it was later discovered that a finite amount of surface could be etched by this solution. This is discussed in the section on results. The implanted samples were ultrasonically cut into the conventional six-probe configuration shown in Fig. l.* In the annealing studies, for which the meas- urements were taken at room temperature, the sample holder was a Bakelite jig incorporating tungsten mechanical probes. The other measurements were taken using a conventional liquid-nitrogen cryostat, in which the temperature could be varied from 77" to about 400°K. For these measurements, 10-mil aluminum dots were evaporated onto the samples and alloyed with the silicon at 530°C for 15 min. The samples were then mounted in flat-packs, and gold wires were bonded to the aluminum dots. The electrical measurements were made with either a Leeds & Northrup K-5 Potentiometer, a Keithley 147 Nanovolt Null Detector, or a Keithley 601 Electrometer. No external bias was applied to the substrate. There is an inherent self-biasing arrangement at one or the other of the current contacts (depending upon the polarity), and this suffices to limit the current flow to the implanted layer. The magnetic field was generated by an A. D. Little electromagnet. Except for occasional checks of linearity of the Hall voltage with

Jan 1, 1969

By W. L. Finlay

Size effects in quenching steel are particularly prominent and well recognized because of the existence of a critical cooling rate separating nuclea-tion and growth transformations, as exemplified by the formation of pearl-ite, from the shear type of transformation characterizing the martensite reaction. The absence of a similar, sharply demarcating cooling rate is characteristic of precipitation hardening systems and size effects in these are correspondingly less prominent. This paper is concerned with a size effect in high-purity, precipitation-hardenable alloys which appears not to have been recognized previously. This effect is believed to result from the thermal fluctuations which inevitably occur in quenching a specimen of finite size into a cooling liquid rather than from the existence of a critical cooling rate. QUENCHING "ANOMALIES" The precipitation hardening literature contains many references to so-called anomalous quenching and aging results. By "anomalous", investigators usually meant that their alloys did not consistently harden on aging after quenching according to some anticipated pnttern: not infrequently virtually no age hardening occurred with compositions known to be precipitation-hardenable. Perhaps the most prominent series of anomalies was reported over a 15-year period by Gayler and coworkers on aluminum-copper.l,2,3,4 Working with silver-rich copper alloy, Cohen5 secured some very interesting Rockwell F hardness changes of from 1-5 Rockwell points between the first peak and valley. Fink and Smith borrowed one of Cohen's specimens and, following his heat treatment and quenching practice to the letter, secured6 very different results in which only one peak was obtained and in which the hardness level at the aging lime of Cohen's first peak was 20 Rockwell F points higher. Fink and Van Horn7 encountered serious deviations in age-hardening high purity aluminum-zinc alloys. They stated that "the discrepancies were larger than might be expected from possible experimental errors in the Brinell readings." Geisler, Barrett and Mehl8 likewise encountered anomalous hardening results in aluminum-silver alloys, securing quite different age-hardening curves from two identical specimens. They stated that "the treatments of these samples had been the same, so that the different behaviors could be attributed only to accidental variations in the quenching practice."

Jan 1, 1950

By W. Klement

By quenching liquid alloys, single-phase solid solutions are obtained in the ranges 0 to 42.0 at. pct Co-Au and 0 to 15 and 75 to about 100 at. pet Co-Cu. Metastable solid solutions are also found in multiphase 42.0 to 49.0 and 69. 0 to about 100 at. pet Co-Au alloys. fie inability to achieve complete solid solubiliiies in Au-co and cu-co alloys is rationalized by a conszderation of the rate processes during cooling and solidification. Trends in lattice distortion and shifts in the compositions of the melting-point minima and critical points are discussed for the binary alloys of copper, silver, and gold with some of the transition metals of the first long period. By rapidly cooling alloys from the melt, a continuous series of metastable solid solutions can often be obtained for components of similar crystal structure which normally form eutectic systems.' The eutectic system Au-Co, Fig. 1, and the peritectic system Cu-Co, Fig. 2, were investigated in order to determine the extent of the metastable solid solutions attainable with the present technique.* EXPERIMENTAL PROCEDURES Most of the alloys were prepared by melting weighed quantities of the elements (purity greater than 99.9 pct) under hydrogen in alumina crucibles by means of induction heating. After reweighing, the alloys were cast under argon into 1 mm diam wires. However, it was not possible to prepare some of the Cu-Co alloys with the requisite homogeneity (over about 1 mm3) in this way. For these alloys, reduced powders (purity greater than 99.9 pct) were mixed for 12 to 48 hr, pressed into compacts that were sintered at 1000º to 1050°C for 6 to 48 hr under hydrogen, and then furnace-cooled. Alloy charges of a few mm3, cut from the cast wires or chipped from the sintered compacts, were heated to 1550º to 1600°C in 30 sec in an alumina insert held within a graphite support and then ejected by a pulse of helium onto a lightly polished copper strip on the inner periphery of a rotating wheel. The

Jan 1, 1963

By William A. Kapp

INTRODUCTION Coal is being mined from beneath residential areas, structures, bodies of water and other surface features in the coalfields to the north, south and west of Sydney. The particular problems faced by mine operators in these areas vary considerably due to differences in the overlying strata, the variation in the depths of cover and also depend on the number of seams being mined. Detailed subsidence work first commenced in the Southern Coalfield in 1965 and is now being carried out over areas of extraction at roost collieries. The analysis of the results of the early investigations and of the work which continues in other areas has shown that there is a consistent relationship between subsidence and mine geometry and has led to a reliable empirical method for the prediction of subsidence. In addition, particular aspects of each of the studies in the Southern Coalfield results in a clearer understanding of strata movements and of the resulting subsidence. The features of a subsidence trough apply generally to all areas but the magnitudes of specific features vary according to the stratigraphy of the particular coalfield. The aim of the subsidence work is to quantify the effects of subsidence for a range of mining geometries and mining conditions to enable the maximum safe recovery of coal from beneath surface features. The importance of local subsidence investigations is becoming more evident to mine operators and to authorities or organisations with surface interests. The subsidence work also provides important information on the stabilities of pillars of coal which remain unmined between panels of extracted coal. These pillars are not extracted either because of poor mining or geological conditions, or because pillar extraction is not part of the particular mining operation. Subsidence studies over these coal pillars clearly establish whether the pillars have remained stable or have failed to support the overlying strata. With subsidence studies continuing over several years, it is possible to assess the stabilities of these pillars on a long term basis. BACKGROUND TO THE STUDY OF SUBSIDENCE Geographical setting Most of the black coal production in Australia comes from the Sydney Basin. The coal seams extend for approximately 350 km along the coast of New South Wales and inland for distances up to 150 km. The City of Sydney is located near the centre of the coastal extent of the Basin where coal has been mined at a depth of 900 m. The Sydney Basin is part of the Main Coal Province of NSW and is divided into several coal- fields. The Southern Coalfield to the south of Sydney contained 15 operating mines and produced 12.7 million tonnes of raw coal during the 12 months to June 1981. The collieries discussed later are shown in Fig. 1. The prominent topographical feature of the area is the Illawarra Escarpment which rises to 400 m above sea level, or 300 m above the coastal strip along the South Pacific Ocean. The escarpment is mainly sand- stone and the weathering of the cliff line has resulted in a covering of talus material at its base. Several collieries are located near the seams which outcrop along the escarpment. The city of Wollongong is located in a scenically attractive area on the coastal plain. The suburbs of Wollongong extend north along the coastline, south to beyond Lake Illawarra and west to the lower slopes of the escarpment. The Illawarra Escarpment forms the eastern boundary of the Woronora Plateau. On a regional scale the surface dips gently to the west and thus forms a watershed for the rivers, most of which flow in a general north westerly direction, sometimes forming steep gorges in the sandstone. These rivers join the Nepean and Hawkesbury River system and flow into the Pacific Ocean north of Sydney. Seven dam have been constructed over the Southern Coalfield (Fig. 1) and with one large dam further to the west, their stored waters provide the needs of the Cities of Sydney and Wollongong and the surrounding districts. A large part of the area affected by mining is the undeveloped bushland of the associated catchment areas. In general no special precautions have been required with respect to subsidence with the exception of the dam structures and stored waters. With the increase in coal mining activities and the expanding residential development south of the City of Campbelltown in the outer Sydney Metropolitan area, subsidence is becoming an increasingly important area of research. Structures which have been affected or considered are townships and extensive residential areas, buildings of historical importance, major tollways, and a high pressure natural gas pipeline. The subsidence effects of mining beneath natural features within national parks is coming under study as mining approaches these areas. Geological setting The coal seams of the Southern Coalfield lie within the Illawarra Coal Measures. They contain high rank coking coal used in the local steel industry and for export. The Bulli Seam is mined extensively through- out the Southern Coalfield with the lower Wongawilli Seam being second in importance with regard to coal production. The top of the Bulli Seam is taken to be the marker horizon between the Permian Coal Measures

Jan 1, 1982

By Carl Altstetter, Emmanuel deLamotte

The influence of an external stress and plastic deformation on the allotropic transformation of single crystals of a Co-30.5 pct Ni alloy was investigated. Experimental results were obtained from dilatometry, X-ray diffraction, and optical and electron microscopy. The effects of stresses could be conveniently divided into three stress ranges. In range I, from 0 to about 400 g per sq mm, the specimens exhibited a multi-variant phase change on cooling and a considerable amount of retained cubic phase. In range II, from 400 g per sq mm to the elastic limit, hexagonal regions of a given orientation grew in size and the cubic phase disappeared with increasing stress level. In range III, just above the elastic limit, specimens transformed into hexagonal single crystals. It was found that plastic deformation, not applied stress, was the factor which determined whether a single-crystal product was formed. The observed macroscopic shear directions were mainly (112) on cooling, but the behavior was more complicated on heating under stress. To explain these properties of the phase change, a model based on the nucleation of partial dislocations is proposed. IT is well-known1 that, on heating, hcp cobalt transforms into an fcc arrangement by shearing on close-packed planes. The crystallographic orientation relationship of the phases is as follows: the habit plane is (OOO1)hcp ?{lll}fcc and a (1010)hcp direction is parallel to a (112)fcc direction. The temperature at which the transformation occurs in pure cobalt is around 420.C 1,2This temperature decreases with increasing nickel concentration: and at about 30 pct Ni it reaches room temperature. However, many of the transformation characteristics remain essentially the same, particularly the crystallographic features.495 A convenient way of studying the transformation is to alloy cobalt with nickel, thus avoiding the difficulties of doing experiments at the high temperatures needed to transform pure cobalt. Due to the hysteresis of the transformation it is possible to choose a Co-Ni alloy with an Ms temperature below room temperature and an A, temperature above room temperature. Either structure of such an alloy could then be studied at room temperature, depending on whether it had just been heated or cooled to room temperature. The choice of nickel is further favored by the small difference in lattice parameters between cubic cobalt and nickel and the similarity of their physical, chemical, and electronic properties. Co-Ni alloys are reported to have neither long- nor short-range order.6 The main purpose of this work was to investigate the influence of an external stress on the transformation characteristics of Co-Ni single crystals. It may be expected that slip, twinning, and transformation should have many features in common in cobalt, because the (111) planes of the cubic phase operate as slip planes when plastic deformation by slip occurs, they are the twinning planes, and they are the habit planes for the transformation. Many previous investigators7-&apos;6 have concluded that dislocations must play an important role in the nucleation and propagation of the transformation, just as they do for slip and twinning propagation. An external stress will affect their motion, and a study of its influence should yield further information about the atomic mechanism of transformation. The present work extends that of Gaunt and christian17 and Nelson and Altstette18 in both qualitative and quantitative effects of stress. The basic concept underlying all the present theories of the transformation of cobalt and Co-Ni alloys is the motion of a/6<112> partial dislocations over {1ll} planes of the cubic lattice. The ABCABC... stacking of the close-packed planes of the cubic phase can be changed into the hexagonal ABABAB... stacking by the sweeping of an a/6 <112> partial on every second plane. Twinning, on the other hand, requires a shear of a/6 <112> on each close-packed plane. The reverse transformation can be effected in a similar way by a/3 (1010) dislocations moving over every other basal plane of the hexagonal phase. Transformation theories2, 7- 12,14 differ in the details of the nucleation of the transformation and the propagation of the partial dislocations from plane to plane. EXPERIMENTAL PROCEDURE Nickel and cobalt rods supplied as 99.999 pct pure were induct ion-melted together under a vacuum of about 10-5 torr in a 97 pct alumina crucible. An alloy containing 30.5 pct Ni was found to have the desired transformation range, with an Ms near -10°C and an j4s in the vicinity of +10O°C. The ingots were swaged to &--in. rod and electron beam zone-leveled in a 10-6 torr vacuum. This procedure resulted in 12-in.-long single fcc crystal rods (designated I to VII) from each of which several tensile specimens of identical orientation were made. Chemical analysis of the bar ends indicated no contamination or gross segregation and no micro segregation was seen in electron micro-probe scans. Tensile specimens with a 9/32-in.-sq by 1-in.-long gage section were spark-machined from the rods and then electropolished or chemically polished to remove the machining damage and to provide a flat surface

Jan 1, 1970

By A. Eilers

(Butte Meeting, August, 1913.) A NUMBER of the copper refineries in this country have lately separated some of the rarer metals from the slimes in the refinery tanks One of these has furnished me the following table of recoveries from given amounts of blister. I publish . this to show the proportions, to gold and silver and to each other, in which these rarer metals may be expected to occur in copper from certain localities.

Jan 6, 1913

By Caudle B. H., Cooper H. E. Jr., O. K. Kimbler

The results of studies of areal sweepout behavior in nine-spot injection patterns are presented in this paper. The ratio of the production rates of the two types of producing wells in a nine-spot pattern is considered in its effect on breakthrough. A model study was used to develop a method to predict the production histories of both side and corner wells and to develop the production history of the pattern or the field. INTRODUCTION The importance of areal sweepout behavior in injection operations has been recognized for a number of years. We now know that the fraction of a reservoir which will be reached by an injected fluid is a function of the geometric arrangement of the production and injection wells and of the mobility ratio of the fluids. Of these two, the mobility ratio (which is a measure of the relative ease with which the oil and the injected fluid can move through the reservoir) appears to have the greatest effect on recovery. The effect of mobility ratio on production history has been reported for most of the dispersed injection patterns (i. e., five-spot, staggered and straight-line drives).4-6 ere has been very little published on the nine-spot injection pattern. This may be because the two types of producing wells in the nine-spot pattern can—and sometimes should —be produced at different rates. This adds a second variable (the fist being mobility ratio) to be covered in a study of the nine-spot flooding network. Muskat1 has reported the sweep pattern efficiency at breakthrough for a mobility ratio of one at various ratios of producing rates for the two types of wells. For these conditions he found maximum oil production at breakthrough to occur when the corner well (the producing well farthest from the injection well) is produced 10.7 times as fast as the side well. Other investigatorsa2,3 have studied a few of the many possible operating conditions possible with this injection pattern. This paper presents the results of studies which are strictly applicable to a nine-spot injection pattern surrounded by other nine-spots in a homogeneous reservoir and which has no flowable gas present (no oil bank is formed). Although the full ranges of the variables mentioned above have not been covered, the results reported here should allow reasonable estimates of field operations to be made. EXPERIMENTAL The well spacing geometry of the nine-spot pattern is shown in Fig. 1. Here we see that each injection well is surrounded by eight production wells arranged in a square. Four of these producing wells are located at the corners of the square; the other four are in the midpoints of the four sides. These two types of producing wells are called "comer wells" and "side wells" respectively. It is the ratio of the producing rates of these two types of wells that affects the breakthrough recovery, as calculated by Muskat.&apos; This ratio is defined as the total producing rate of a corner well divided by the total producing rate of a side well. The model used in this study represented one-eighth of a nine-spot pattern, as shown in Fig. 1. It contained the equivalent of one-fourth of a side well, one-eighth of a comer well, and one-eighth of an injection well. Because of these proportions, the actual producing rate ratios in the model were one-half of the ratios of producing rates as

Jan 1, 1965

By M. Kaufman, D. Rosenthal

IT would be of great importance to our understanding of the phenomena of fracture in metals if a unique relationship could be established between stress and some easily measurable parameter of deformation up to the fracture. It is known that no such relationshir, has been found when the parameter was the mechanically measured strain,&apos; the major part of which is plastic. The present investigation was initiated to determine, among other things, if the X-ray or lattice strain" might be a • For the definition of lattice strain see ref. 2. more suitable parameter. To this end, annealed stress free*&apos; specimens of 61s aluminum alloy were ** Freedom of stress in this particular case means absence of those stresses which can be checked by the technique employed. tested at room temperature and liquid nitrogen temperature (—195OC), by first maintaining the same temperature from the beginning until the end of the test, and then with crossovers from one temperature to the other. Three major factors had to be taken into consideration in designing the specimens and testing equipment. The test setup must allow X-ray pictures to be taken while the specimen is under load (for as much as 2 hr at a given load). Provision must be made for maintaining the test specimen at the temperature of liquid nitrogen as well as at room temperature. In addition, the specimen must be able to rotate to allow the X,ray beam to take in as large a sample of grains as possible, to maintain centering, and to correct for effects of large grains. The final design of the specimen and equipment is shown in Figs. 1 and 2. The specimen and grips are hollow, enabling liquid nitrogen to be poured in through a funnel-container arrangement while the specimen is rotating. The diameter of the specimens at the 2 in. gage section is 5/16 in. with a 3/16 in. diameter hole through the center. A small pilot valve in the lower grip allows a very small stream of liquid nitrogen to escape, thus assuring circulation of the liquid at all times. A low temperature silicone grease-tissue paper packing is used to seal all joints. The specimen is held in the grips by a pin. Spherical socket joints at top and bottom are used to allow for proper alignment. The grips are connected to the thrust bearings by means of plastic couplings to decrease the heat flow. Rotation is accomplished by means of a motor which drives a plastic gear (integral with the lower coupling) through a semiuniversal joint to allow for deforma- tion of the specimen. The torque applied to the specimen is very small. The maximum stress caused by this torque at the highest loads reached was found to be less than 200 psi, The whole unit was mounted in a 10,000 Ib testing machine. An insulation cage was placed around the specimen to cut down air circulation, and consequent frosting of the specimen, and also to reduce radiation and convection heat losses. A narrow window, covered on both sides with a thin plastic materiai allows the X-ray beam to reach the specimen. Thermocouples placed just outside the pilot hole at the lower grip, in the bottom of the funnel container and near the top of the funnel container permitted checks of the

Jan 1, 1955

By Jill Dill Pasteris

Several mineralogical prospecting techniques are used in diamond exploration. Most are concerned with identifying indicator minerals such as pyrope garnet and magnesian ilmenite, which are derived from mantle xenoliths hosted by kimberlites. The first goal of such prospecting is to locate kimberlite intrusions; the second goal is to identify the diamond-bearing kimberlites. Explorationists have worked much less on the indigenous kimberlite phases. The kimberlitic opaque oxides, ilmenite and particularly spinels, promise to be useful in discriminating between intrusion episodes in identified kimberlites, and perhaps in the evaluation and prediction of diamond grades. Several petrologists have showed that spinel compositions and zoning patterns are specific to certain intrusive facies in South African and Canadian kimberlites. Careful evaluation may indicate a correlation between spinel parameters and diamond content.

Jan 1, 1984

By I. C. White

Only two factors appear to be directly responsible for the geographic distribution of sulfur in the coal fields of West Virginia: these are the stratigraphic position of the coals in question, and the eastward or westward location of the deposits. There appears to be a progressive increase in the sulfur content of West Virginia coals from the oldest Peqnsylvanian deposits in the Pocahontas, New River, and Kanawha Groups of the Pottsville Series up through the Allegheny, Conemaugh, and

Jan 1, 1920

By G. Sachs, B. B. Muvdi, E. P. Klier

IT is now generally i-ecognized that hydrogen is responsible for delayed failures encountered in high-strength steels,&apos;.&apos; and the hydrogen responsible for the embrittlement is introduced in the cathodic cleaning and plating operations to which these steels are subjected. Numerous test methods have been used in the past for the determination of brittleness in embrittled parts, namely tension? = notch-tension:&apos; impact,&apos; stress-rupture: a and bend tests.% * Several of these tests are not suitable for routine testing.

Jan 1, 1958

By P. R. Kalischer

IN the production of alloys by powder metallurgical processes it is often necessary or desirable to include one or more components that tend to form very stable oxides Included in this group of metals are aluminum, manganese, magnesium, silicon, and a few others In many cases it is not necessary for the sintered compact to have full density and the other physical characteristics of a cast alloy and in that event no undue precautions need be taken If, however, it s required that the sintered part be entirely homogeneous, and have maximum density and physical properties, some method must be found to reduce the surface films of oxide, which are always present on the metals, and for the metals mentioned above this is always extremely difficult, if not impossible Since the production of high-density alloys is of particular interest to powder metallurgists, some experiments were undertaken to devise methods of reducing the refractory oxides For this work, alloys of iron, nickel, and aluminum were chosen because aluminum oxide is one of the most stable oxides and because these alloys in the right compositions form excellent permanent magnets All of the pertinent properties of the magnets could be accurately and delicately measured by density measurements and magnetic tests of sufficient scope to give a complete demagnetization curve From such a curve the maximum coercive force, residual magnetism, and energy products could be obtained and compared with the same properties for a cast material Any lack of homogeneity, density, or solid diffusion would be immediately apparent as a decrease in the magnetic properties NATURE AND REMOVAL OF SURFACE BARRIERS The early work of the present investigation was based upon published processes In the published information it was claimed that by intimately mixing iron, nickel, and iron-aluminum alloy (50 per cent Fe, 50 per cent Al) powders, compressing such a mixture into the desired shape and size, and then sintering (heating to a temperature below the melting point of the component metals) in hydrogen at 1200ºC or higher, a sound, homogeneous article could be made having the desired physical size, shape, and strength, and good magnetic characteristics However, this early work showed clearly that something in the powder compress was inhibiting diffusion and the process was almost entirely unworkable In the initial phase of the investigation samples of iron powder, nickel powder, and iron-aluminum alloy powder were pressed into separate bars and sintered in hydrogen Both the iron and nickel powders sintered

Jan 1, 1941

By J. M. Gaines, C. H. Herty, M. W. Lightner, H. Freeman

Few subjects have attracted the attention of metallurgists more than oxygen in steel. From the days of Mushet and Ledebur interest in this subject has been increasing, and as additional knowledge has become available, the problem has naturally grown more complex. Instead of using the simple term "oxygen" we now distinguish between iron oxide, silicates of various kinds, oxysulfides, oxygen as gas and oxygen in solid solution in steel. There are five general methods for determining oxides in steel: hydrogen reduction; vacuum fusion; various wet-extraction methods, including electrolytic methods; methods depending on volatilization of the iron away from the oxides; and metallographic methods. For oxygen in solid steel each of these methods has both advantages and disadvantages. The hydrogen-reduction method is of no use on steels above about 0.20 per cent. carbon;&apos; furthermore, it gives only FeO and possibly some MnO. The vacuum-fusion method2 is expensive and gives total oxygen, with the exception of some A12O3, and does not differentiate between the various oxides in which the oxygen exists. Most of the wet extraction methods3 give only the more insoluble oxides SiO2 and A12O3, though the iodine method gives MnO to an uncertain degree (information that may be more misleading than no information

Jan 1, 1930

By Carle Hayward

AT THE February, 1916, meeting of the Institute, a paper presented by Hayward and Raymond gave the results of a study on the effect of time in tempering medium-carbon steel, when the following conclusions were reached: It is not fair to consider the question settled when only three specimens were used for each treatment, but the results obtained indicate that for reheating quenched medium-carbon steel to temperatures below 500° it is only necessary to heat it through. Longer heating has little or no effect on the tensile strength, ductility, or hardness. At temperatures above 500°, increasing the time of treatment causes a slight falling off in hardness and tensile strength with a corresponding increase in ductility. In the discussion of the paper these conclusions were attacked and evidence presented that seemed to throw doubt on their accuracy. The authors, however, showed that this evidence was based on high-carbon or alloy steels and no facts regarding medium-carbon steel were presented. During this study the heat treatment was carried out in a small electric resistance furnace. It held nine specimens, but when these were placed in the furnace the temperature was lowered to such an extent that 30 to 40 min. were required to reach the desired heat. The authors pointed to this as a weak point in the investigation and it seemed wise to supplement the research by work on similar steel but using a different method of heating. This has been done and the results are given in the present paper. The Rhode Island Tool Co. cooperated by furnishing the steel and turning the tensile specimens.

Jan 1, 1922

By A. R. Troiano, E. A. Steigerwald, F. W. Schaller

The initiation of localized cracking in hydrogenated high strength steel was dependent on the developmeni of a critical hydrogen conceniration and relatively insensitive to the magnitude of the applied stress. The stress was believed to influence the deluyed failure process by providing the means for grouping the hydrogen. On the basis of an assumed distribution law the observed changes in the lower critical stress as a function of notch acuity, yield strength, and temperature were predictable over a significant range of these variables. THE phenomenological characteristics of delayed failure in high-strength steel have been comprehensively investigated and the behavior has been attributed to the strong embrittling action of hydrogen.1-3 Delayed failure or, as it is also termed, static fatigue, is the most sensitive means of detecting hydrogen embrittlement since it allows the maximum time for hydrogen diffusion during a test.3 The nature of delayed failure cail be aptly described by four parameters which are schematically depicted in Fig. 1. The upper critical stress corresponds to the rupture stress in a conventional notch tensile test. The lower critical stress or static fatigue limit is the stress below which no delayed failure will occur. The incubation period is the time required for the formation of the first crack and the fourth parameter is the failure time. An increase in hydrogen content, notch acuity, or strength level of the material increases the susceptibility for delayed failure by decreasing the lower critical stress, the incubation period, and the time to failure.lY3 A decrease in test temperature prolongs the incubation period in accordance with the lower diffusion rate of hydrogen, and also de-

Jan 1, 1961

By L. J. Buck

Lead smelting in the ore hearth, first practiced in Europe, whence the traditional name "Scotch hearth, and later developed in America to its present efficiency, is based upon the roast reduction process and is applicable to relatively high-grade galena concentrates. The roast reduction process embraces not only the roast reactions: 2PbS + 70 = PbO + PbSO4, + SO2 PbS + 2PbO = 3Pb + SO2 PbS + 2PbSO4 = Pb + 2PbO + 3SO2 but also, by reason of the addition of extraneous fuel, the reduction reaction: 2PbO + C = 2Pb + CO2 Thus in the ore hearth the roasting of lead sulphide, forming lead oxide and lead sulphate, the reaction of lead oxide and lead sulphate with lead sulphide producing lead, and the reduction of lead oxide by carbon producing lead, go on simultaneously. The Ore Hearth Function of the Ore Hearth.—The ore hearth, through the roast reduction process, provides for the extraction of lead and the immediate disposal of the smelting products—fume, hearth slag and lead, all of which are subsequently treated as follows: the fume is recovered in the flue system and baghouses, mixed with concentrates, and returned to the ore hearth in the form of ore mix; the hearth slag is smelted in a blast furnacc for the further recovery of lead; and the lead is refined and cast into a marketable product. Concentrates Amenable to Ore-hearth Smelting.—Only concentrates that are high in lead content, 70 per cent or more, are ordinarily considered amenable to ore-hearth smelting. Silica should not exceed 2 per cent and iron is allowable only to 4 per cent. These slag-forming constituents occlude both sulphide and mctallic lead, prevent the elimination of sulphur and decrease the lead extraction. Lime and magnesia are beneficial in that both favor a dry slag, promote elimination of sulphur, and prevent occlusions of metallic lead.

Jan 1, 1937

By Edgar R. Kendall

A knowledge of the fundamental principles of locating, sampling, testing and evaluating materials is essential in prospecting for mineral aggregates. In this discussion, mineral aggregates will be considered sand, gravel, crushed stone and slag that are used as materials of construction. The quantity of mineral aggregates produced in the United States during the year 1935 for such purposes was roughly 165,000,000 tons, about 60 per cent of which was sand and gravel, 37 per cent crushed stone and 3 per cent crushed slag. The total value of this material was approximately $100,000,000. It is apparent therefore that the prospecting for suitable mineral aggregates is of considerable economic importance. In prospecting for mineral aggregates, the methods employed are the same whether the organization is large or small. In the large organization there may be available geologists for locating sources of supply, a land acquisition department to arrange for the necessary options or permits, engineers to do the sampling, a laboratory for testing, and a board of consulting materials engineers to make the final selection. Even small organizations must follow the same general procedure, though the responsibility for the selection of aggregates may rest with one man, who may or may not be an engineer, but who must depend entirely upon his own judgment. Locating the Supply The initial step in prospecting for mineral aggregates is the locating of suitable, adequate and economic sources of supply for the project in mind. Commercial plants in the vicinity should be investigated and a survey made of the existing structures that have been built of aggregates from these sources. If the structures are rather old and show no signs of deterioration, it is fairly good evidence that the aggregate is satisfactory. If materials of the proper quality can be obtained from commercial sources in sufficient quantity, and delivered to the job economically, it

Jan 1, 1942

By Edgar R. Kendall

A knowledge of the fundamental principles of locating, sampling, testing and evaluating materials is essential in prospecting for mineral aggregates. In this discussion, mineral aggregates will be considered sand, gravel, crushed stone and slag that are used as materials of construction. The quantity of mineral aggregates produced in the United States during the year 1935 for such purposes was roughly 165,000,000 tons, about 60 per cent of which was sand and gravel, 37 per cent crushed stone and 3 per cent crushed slag. The total value of this material was approximately $100,000,000. It is apparent therefore that the prospecting for suitable mineral aggregates is of considerable economic importance. In prospecting for mineral aggregates, the methods employed are the same whether the organization is large or small. In the large organization there may be available geologists for locating sources of supply, a land acquisition department to arrange for the necessary options or permits, engineers to do the sampling, a laboratory for testing, and a board of consulting materials engineers to make the final selection. Even small organizations must follow the same general procedure, though the responsibility for the selection of aggregates may rest with one man, who may or may not be an engineer, but who must depend entirely upon his own judgment. Locating the Supply The initial step in prospecting for mineral aggregates is the locating of suitable, adequate and economic sources of supply for the project in mind. Commercial plants in the vicinity should be investigated and a survey made of the existing structures that have been built of aggregates from these sources. If the structures are rather old and show no signs of deterioration, it is fairly good evidence that the aggregate is satisfactory. If materials of the proper quality can be obtained from commercial sources in sufficient quantity, and delivered to the job economically, it

Jan 1, 1942