Search Documents

By Henry N. Toler

Development in the Jackson gas field, Hinds and Rankin counties, for 1935 continued at a slow pace, there being only nine wells drilled on the structure, of which five resulted in gas producers and four in dry holes. There were no wells drilled deep enough during 1935 to test any of the horizons below the producing Selma chalk. There are 113 producing gas wells in the Jackson gas field, with three wells on the southeast edge of the field making some oil with a large quantity of salt water; this oil comes from the same horizon as the gas. The combined open flow of the 113 gas wells is about 4,100,000,000 cu. ft. The proven area of the field is approximately 8000 acres. The production of 10,291,000,000 cu. ft. for 1935 represents the largest yearly pull from the field by almost a billion cubic feet. The total production from the field to date is 45,104,000,-000 cu. ft. It is interesting to note that the rock pressure has dropped from 1010 lb. per sq. in. initial to 943 Ib. at the end of 1935, a decline of only 67 lb. in 6 years. There is a difference of opinion as to the age of the deepest formation tested on the Jackson structure; some people holding that it is Tuscaloosa, others, Trinity, and still others that it is Paleozoic, probably Pottsville. The production of the Amory gas field, Monroe County, continued to decline and the capacity was far under the demand. Originally there were four producing wells in the field with a combined open-flow capacity of approximately 15,000,000 cu. ft. and a rock pressure of 680 lb. per sq. in. At the end of 1935 only two wells were producing with a combined open-flow of less than 1 million cu. ft. and the rock pressure down to 100 lb. or less. No attempt has been made to drill new wells in the immediate field but three wells are being drilled in the county in an effort to secure new supplies of gas. The wildcat operations for 1935, with only 11 wells drilled, were the lowest since 1932, just about one-half the number drilled during 1934. None of the wildcat wells drilled in 1935 resulted in producers and, so far as the writer is aware, did not uncover any large structures. The 11 wells drilled were abandoned or junked at comparatively shallow depths, except the well drilled in George County to 6928 ft. by the United Gas

Jan 1, 1936

By H. H. Rachford, J. Douglas, D. W. Peaceman

A numerical solution of equations describing two-phase flow in porous media shows promise in providing a technique for predicting the displacermet from satlds of oil by water or gas. The description includes the influence of relative permeability, fluid viscosities and densities, graviry, and capillary pressure, and, tholrgh tested ortly for two-dimensional cases, should be eqlmlly applicable in three-dimensional geometry. Two memorical methods ore presented: the first method is quite general in its applicability; the second method can be used only with certain types of boundary conditions but requires less computing. Comparisons of computed results with data from Inhoratory models are presented. These data were taken on a water flood of a strarified model and on water floods of a five-spot model for favorable and unfavorable mobility ratios. On the stratified model, excellent agreement with recovery at breakthrough was obtained; agreement with recovery after breakthrough was poor. In the five-spot model, good agreement was obtainecl with recovery at and after breakthrough. The purpose of this paper is twofold: first, to present a reservoir engineering method requiring knowledge only of rock geometry and the normally measured rock and fluid properties for calculating the multi-dimensional flow of water displacing oil from porous, water-wet rock containing connate water; and, second, to investigate the validity of the method by comparing results of calculations with previously observed displacements in laboratory models. The availability of such a verified technique of reservoir analysis would afford major advantages. First, it would demonstrate that the fundamental macroscopic concepts of two-phase fluid mechanics, i.e., relative permeability and capillary pressure, yield an adequate description of the physical process. Also, since most reservoir rocks appear to be water-wet and contain connate water along with oil, it would provide a method of technical and economic value for calculating the course of oil displacement by water directly from measured reservoir and fluid properties. It is important to emphasize that the calculation is subject only to the limitations of detail and precision of reservoir information, but not to limitations introduced by simplifying assumptions. Further, it would providc almost the only means of examining the influence of factors such as the size and extent of reservoir inhomogeneities and uncertainties in the basic reservoir data. Knowledge of this influence is essential in stating quantitatively the detail required to define a reservoir and in establishing the relation between the uncertainty in the definition of reservoir properties and the reliability of predicted performance. Moreover, in the process of solving a particular problem much detailed information would become available about the displacement process. For example, at each point in the reservoir for all stages of the displace ment. the calculations would yield not only the water and oil saturations but also the direction and magnitude of fluid velocities and the local fluid mobilities. Such dctail is potentially of great value in giving insight into the mechanics of particular displacements. The development of such a method has long been the goal of research in the application of numerical an-alysis to petroleum reservoir enginecrinz. The most complete treatment of the displacement process published to date is that of Douglas. Blair, and Wagner,' which, however, was limited to flow in a single dimension. The method presented in the present work is hascd on the numerical solution of a finite difference analogue of the multi-dimensional differential system describing the displacement process. Although current work has considered only displacement of oil by water from water-wet sands, the differential system for other immiscible displacements, such as gas displacing oil with which it is in phase equilibrium, is quite similar. It should therefore be expected that the technique described will be applicable to displacement by gas as well. The description of the simultaneous flow of fluids through porous media in terms of relative perrncability and capillary pressure has been adequately discussed in the literature and standard textbooks. Sec, for exampje, Muskat. Chapter VII.'

By V. R. Garfias

INTRODUCTION FOR a number of years the senior author has been interested in the various geologic and engineering problems involved in the development of the petroliferous districts of northeastern Mexico, having in a previous paper 1 endeavored to present a summarized statement of the information relating to the geology and soil resources of this region. Of the many interesting geologic phenomena, perhaps those which have been the object of more speculation relate to the igneous intrusions which, in places, have a controlling influence on the accumulation of oil in commercial quantities, a relationship which has been tentatively explained by various observers with as many interestingly different views. The authors of the present paper aim to record, in the course of a general discussion of the various viewpoints, some additional data, and present further tentative conclusions with a view to rounding out an up-to-date summary of the subject. The greater part of the area in question lies in the State of Vera Cruz, only a northwest fraction being in the State of San Luis Potosi. Vera Cruz is bounded on the north by the State of Tamaulipas, the northernmost of the Mexican States along the Gulf. The topography of the States of Tamaulipas and Vera Cruz and of Texas and Louisiana to the north, is controlled by the Gulf coastal plain which in northern Vera Cruz has an average width of about 60 miles, the transitional topography between that of the rugged flanks of the Sierra and the lowlands of the coast being made up of a series of terraces and irregular hills and valleys.

Jan 8, 1917

By R. A. Fitch, J. D. Griffith

A performance calculation method was used in conjunction with experimental studies to develop means of predicting and interpreting miscible floods and to explore possible methods. of improving their efficiency. The calculation method is based upon the division of reservoirs into multiple independent zones or strata. Comparison was made with some experimental floods and with a field project to obtain some measure of the applicability of the method. Two aspects of miscible flooding were considered: (I) the displacement of a miscible front through a reservoir, and (2) the distribution and utilization of the solvent volume injected to maintain miscibility. Calculations and experihental observations indicate that alternate gas-water injection behind a miscible front significantly improves miscible flood performance, both within a single stratum and in a multistrata reservoir. Calculations were made on the extent to which miscibiliry is maintained by a given solvent volume in a stratified reservoir. Two alternate criteria for determining the optimum volume of solvent for injection are discussed. The preinjection of a small volume of water ahead of the solvent is suggested as a method of obtaining more efficient utilization of solvent. Calculations and experiments were made to investigate the effects of water preinjection. INTRODUCTION Miscible fluid displacement as a possible means of recovering oil has been the subject of extensive research and numerous field tests over the past several years. This work has brought out both favorable and unfavorable features of the miscible recovery methods. Many tests have shown that a miscible fluid can displace all of the oil contacted, leaving no high residual oil saturation, as is characteristic of immiscible displacements. The miscible methods have proven dificult to control, however, as evidenced by early breakthrough of the displacing fluid and poor sweep efficiency in several field projects. It became apparent early in the investigation of miscible displacement that the development of improved techniques and better methods of control would be required to extend the range of applicability to any significant portion of our petroleum reservoirs. The purpose of this study was to consider the problem of designing miscible floods to obtain better performance. A performance calculation was used in conjunction with experimental studies to develop means of predicting and interpreting miscible floods and to explore possible methods of improving their efficiency. Two aspects of miscible floods were considered separately in this study and the results are presented in two parts. The first part concerns the manner in which the miscible front is displaced through the reservoir. In these calculations the condition of miscibility between the reservoir oil and the displacing fluid is assumed. In the second portion the distribution and utilization of the preinjected solvent in maintaining rniscibility is considered. This portion dealing with solvent utilization applies only to the enriched gas or LPG slug processes. CALCULATION METHOD AND EXPERIMENTAL STUDIES COMPUTATIONAL MODEL The calculations for expected reservoir performance are based upon the multi-strata concept of reservoir properties. The method assumes multiple, independent strata (no crossflow between strata) and explicitly includes variations in patterns, injectivity, areal sweep and displacement efficiency. Lateral variation in permeability within the strata (for example, directional permeability) may be considered in the calculations, provided the variations are similar in all strata. The calculations based on this model furnish the rates of injection and rates of production of both oil and the displacing fluid for the composite system of strata. To carry out calculations on the mathematical model described, information is required on the performance of the displacement process under consideration in a single stratum element of the pattern to be used. In particular, for a given pattern and displacement process, data are required relating injectivity and composition of the produced stream to the volume of fluid injected. Data on the variations in areal sweep must also be available if it is desired to track the areal sweeps in the multi-strata model. These data may be obtained from experimental work such as model studies or other suitable methods. This representation of reservoir properties is, of course, an approximation and may be inappropriate in some cases. But the representation is not an arbitrary one since most oil reservoirs are essentially successive layers of sediment with the net producing pay zone often comprising but a fraction of the gross formation thickness. The fact that permeabilities measured in the vertical direction are frequently but a fraction of the horizontal permeability adds some evidence to the validity of this model. This type cal-

Jan 1, 1965

By R. T. Hukki

The purpose of this paper is to present an analysis of the unit operation of grinding and the circulating load, of the unit operation of classification and the circulating load, and of the two superimposed into one operation to clarify the overall trend of events relating the circulating load to the capacity of the closed circuit grinding system, to the specific surface area of the final fine product, and to the energy consumption in the closed circuit grinding process. The capacity of the closed circuit is frequently, if not always, determined by the classifier, not by the mill." With these words a startling idea was expressed in 1934 by Dorr and Anable.1 Today, some 30 years later, grinding in closed circuit is universally accepted. The basic curve presenting the capacity factor versus circulating load by Dorr and Anable has obviously been so convincing that not a single authoritative investigation regarding its validity seems to have been conducted. The only major subject of discussion appears to have been the relative merits of the 'high' and 'low' circulating loads. It seems to be universally agreed that much still remains to be hoped for regarding sharpness of classification. BASIC CURVES FOR CONSTANT MILL LOADING Fig. 1 presents a series of basic curves for constant mill loadings in function of new feed rate and circulating load. The mill loading indicated by each curve is the sum of hourly tonnages of new feed and circulating load. For example, at point 0 where the new feed rate is 100 t/h and the circulating load 300%, or 300 t/h, the mill loading is 400 t/h. In closed circuit grinding, the new feed rate corresponds to the rate of finished classified material produced. Although at this stage the effect of classification is excluded in construction of the basic curves, the trend indicated by these curves is strongly in favor of closed circuit operation under relatively small circulating loads. A study of the curves reveals that, e.g., a mill operating under a load of 200 t/h at point P where the new feed rate is 50 t/h and the circulating load 300% will also operate under the same total load at point Q where the new feed rate is 100 t/h and the circulating load 100%. In other words, a reduction of circulating load from 300% to 100% would lead to doubling of the new feed rate and doubling of the rate of production of finished material, without a change in the total mill loading. The obvious question is, is it also possible by a reduction of the circulating load in a closed industrial grinding circuit to increase the production of finished classified material and, if so, how and to what extent? GRINDING TESTS BY DORR AND ANABLE In a series of open circuit grinding tests reported by Dorr and Anable1 limestone was ground at various feed rates in a 3-ft ball mill. The original data are reproduced in Table I. It can be seen that with the increased feed rate production of -65-mesh material increased and the energy consumption per unit weight of the -65-mesh product decreased in the reverse ratio. The data shown in Table I have been reproduced for our purposes in Table II for a scale corresponding to grinding in a large industrial mill. This reproduction

Jan 1, 1968

By W. A. Schaeffer, M. Albertson

The Yates field is situated in northeastern Pecos County, Texas. Its productive area is about 15,000 acres. Production is chiefly from limestone of Permian age. Depths of wells vary from 1100 to 1800 ft. Initial productions range from a few barrels to 8000 bbl. per hour. The field outlet has always been prorated. Gas-oil ratios originally varied from less than 100 cu. ft. up to 8000 cu. ft. per barrel at allowable production rates. The average ratio was about 500 cu. ft. Fig. 1 shows the structure of the field and the location of the Tippett lease, on which the original experimental tubing work was done. Before the latter part of the year 1929, little actual effort in practice had been given to determination of the conditions under which the highest efficiencies may be realized in naturally flowing wells. For the preceding few years attention had been given to gas-oil ratios and their possible reduction by maintenance of back-pressure by choking at the well head. Some attempts had been made toward reduction of ratio by bottom-hole choking. In late 1929, the Shell Petroleum Corp. started the experimental installation of specially designed flow columns adapted to high-pressure flowing conditions in the Yates field. The objectives in view were the attainment of low gas-oil ratios at low rates of flow and the maintenance of high bottom-hole pressures. All naturally flowing wells should be provided with a suitable eductor string immediately upon completion of the well, so that the benefits of efficient flow will be derived from the beginning. This paper presents a method of tubing for efficient flow and a discussion of some complex factors which influence well behavior. Factors Influencing Gas-oil Ratios Many factors influence the production of gas from naturally flowing wells. The writers believe that in some instances gas control is effected mainly in the reservoir itself, in others in the well bore, and in still others both sets of factors may be significant. Some wells apparently have penetrated productive zones in which practically all of the gas is closely associated with, and mostly dissolved

Jan 1, 1932

By John J. Croston

IN the closing months of 1936 the copper industry gave every evidence that it was at last on the threshold of an improved era. At the beginning of the year prices stood at 9 ¼ ¢, which in itself was a great improvement over prices prevailing for the three previous years. Industry generally was showing signs of moving forward in this country, and business was definitely good in certain foreign quarters. The threat of war and preparations for rearmament in Europe and Asia acted as a further stimulus to purchasing. By midsummer the situation had so improved and stocks had been so reduced that the cartel of foreign producers (including American producers with foreign mines) decided to increase the production quota to 75 per cent on Aug. 1. Large-scale buying gave continued strength to the price and by Oct. 1 the quota was increased to 80 per cent, and again on Oct. 15, to 85 per cent. Notwithstanding this the price of copper continued its advance and on Nov. 1, with stocks declining continuously, the cartel increased operations to 95 per cent, then to 105 per cent on Nov. 5. In the meantime the domestic producers, because of the great increase in home consumption, had increased their production by nearly one-half. At the close of the year copper sold at 12¢ per pound, and since the turn of the present year has reached 17¢. This rapid increase has not been wholly justified. Much of the increase was due to the legitimate demands of recovering industry, but rearmament orders plus accumulation of reserve stocks in case of war, purchases in anticipation of labor strikes and purely speculative activities on the London Metal Exchange accounted for the balance. Certainly in view of the state of industry and the general world price level, it appears unnecessarily high. Talk of a copper shortage is sheer nonsense, the recent condition in the market being created by overbuying, leaving but a small volume for speculative supplies. It takes some months for an increase in mine output to reach the market, but production is again overtaking apparent consumption, stocks have begun to increase, and this, together with the reopening of many small

Jan 1, 1937

By V. C. P. Morfopoulos, N. Arbiter

Theoretical and experimental studies of the interactions of mineral particles with electrical fields of cylindrical symmetry have been made. Theoretically, an expression relating field gradient and intensity to the force experienced by a dielectric particle was derived in a manner paralleling the magnetic analog. Pauthenier's and Cohen's expressions were considered in the evaluation of coulombic forces. Comparison of dielectric and coulombic interactions of minerals exhibiting a wide difference in dielectric susceptibility revealed the potential significance of dielectric forces in a field of appropriate characteristics. Experimentally, apparatus was designed for the study of forces experienced by a single stationary particle in an electrostatic field. This permitted the separate and precise measurement of dielectric interactions in the field. The experimental results were in good agreement with the theory and with relevant published data. Dielectric forces were found of comparable magnitude with coulombic in the presence of an adequate field gradient. Prolonged exposure of minerals to an inhomogeneous field was found to enhance the dielectric response. Dielectric inter- actions properly employed may thus be important in electrostatic concentration techniques. Conventional electrostatic separation techniques employ forces between charged particles and field electrodes to establish the trajectories which effect separation. Uncharged mineral aggregates, although unaffected by homogeneous electrical fields, should respond to fields exhibiting appropriate orientation and electrical gradients. The purpose of this paper is to establish the theoretical and experimental base for the comparison of the forces due to dielectric-field interactions with those of electrostatic origin. Apparatus and techniques developed for the determination of dielectric interactions are described and data on the dielectric forces experienced by stationary particles in cylindrical fields are reported. Finally, a quantitative comparison of dielectric and electrostatic forces is given. THEORY Dielectric Forces: When dielectric particles, minerals for example, are placed in an inhomogeneous field they experience interactions that give rise to substantial dielectric forces.' The latter were shown proportional to the intensity of the field, the potential gradient, the size of the particles and the dielectric permittivity difference between the particles and the medium. The properties of the inhomogeneous field, E, and the magnitude of the gradient, dE/dl, depend on the geometry of the system in question.

Jan 1, 1965

By Ernest R. Darby

If the correct balance between fuel and air is maintained in an open-flame furnace,' little chemical action may be expected between the products of combustion and the metal being melted. Physical' changes in the metal are the object of the melting operation, and indirectly, under certain conditions, may be the cause of subsequent chemical actions. If sufficient heat has been introduced into the metal to bring about the change from the solid phase to the liquid phase, and still further from the liquid to the vapor phase, the metal vapor in all probability will be carried from the furnace by the exhaust and rapidly combined with the oxygen of the outside air. The charge being melted in the furnace may contain elements which are chemically inactive at normal temperatures but which will form compounds at the elevated temperatures of the metal bath, or even at a lower degree. Such indirect chemical actions are very confusing and often lead to incorrect conclusions regarding furnace atmospheres. In the open-flame furnaces used in the melting of bronze, the furnace atmosphere is spoken of as being either neutral, oxidizing or reducing in its effect upon the metal. A neutral atmosphere, as mentioned, is generally considered as the atmosphere of the furnace that will produce melted bronze, neither oxidized nor gassed. It is in effect an atmosphere which is not directly the cause of any chemical action. In such an atmosphere absolutely pure metals may be melted and poured without the absorption of gases or the formation of metallic oxide. The metal has undergone a simple, physical change. An oxidizing atmosphere is one in which the air introduced to the furnace is in excess of that required to complete combustion of the fuel used. The oxygen of the excess air may combine with the metal being melted to form metallic oxide, which may or may not be dissolved by the metal. If an absolutely pure metal is melted in a furnace operating with such an atmosphere, a portion of the metal charged may be converted into metallic oxide, the amount depending upon the duration of the

Jan 1, 1930

By M. H. Sommer

Many attempts have been made to develop a relation between the tensile properties and the deep-stamping qualities of metals commonly used in deep drawing. These operations are generally performed cold and the metal is always stressed beyond the elastic limit. However, the problem cannot be readily solved without a proper investigation of: (1) the relation between actual stress and actual strain in the plastic range and (2) the stresses that are set up in the metal during the process of deep stamping. Much work has been done in recent years to add to our knowledge on plastic deformation of metals and the shortcomings of the ordinary tensile test, particularly in the plastic range, have been sufficiently recognized. It has been widely acknowledged that the local contraction, which appears in a tensile test after the maximum load is reached, is not a general characteristic of the material but is peculiar to this form of testing. The plastic deformation of materials is explained by the slip of their crystals along certain planes and this rearrangement should be similar whether observed in a tensile, compression or torsion test, and if the results of any of these forms of testing show deviations, it must be due to other influences, as for example the local contraction in a tensile test. For this reason the tensile-test curve as obtained from the measurements taken on a tensile-test machine or registered by an autographic device has been supplemented by the so-called "actual stress-strain curve," which is constructed from the observed tensile-test data by eliminating the effect of local contraction and is in complete alignment with the stress-strain values obtained in a compresison or torsion test. The actual stress-strain curve shows the increase of actual unit stress in relation to unit elongation beyond the yield point and beyond the point of maximum load and indicates clearly the extent of strain-hardening which the ordinary tensile-test curve does not reveal. The following metals have been investigated in this paper and their actual stress-strain curves and, further, their char-

Jan 1, 1934

By Morgan Walker, C. D. Watson, Reid W. Bond, D. L. Trax

Common practice in the Mid-Continent until recently was to prolong the natural flow of oil wells as long as possible by agitation, and then swab for a short period until the well was put on the pump. Comparatively recently the gas-lift has superseded the swabbing and agitating period and in some cases encroached on the natural flowing life, particularly where it was evident that the potential oil capacity of the well was greater than the gas supply, or lifting medium. The majority of wells are finished with either 6¼, 65/8 or 8¼-in. casing and connected to a separator through a flow line which is usually 65/8 in. The flow line is generally designed to eliminate sharp turns and has reduced the gas-oil ratio and therefore increased the efficiency in a good many instances. Until recently all wells were allowed to flow without restriction against the possible trap pressure until it was deemed advisable to put them on gas-lift. This resulted in a fairly efficient flow during the early life of the well if the well was rather large but was usually inefficient in small wells and in the later flowing life of large wells, on account of the large area in the casing and therefore excessive slippage. Recently, considerable effort has been made to increase the efficiency of small flowing wells by running tubing to eliminate as much slippage as possible. With large wells there is a considerable trend toward back-pressuring, or beaning to find out whether it is possible to reduce the gas-oil ratios and increase the flowing life. The greater number of fields that have been back-pressured have been produced in that manner through necessity, either to restrict production for proration purposes or, in fields producing by hydraulic pressure, to reduce water encroaching. The recent Cromwell sand development in Little River is an example where both back-pressuring by means of high-pressure traps and beans and flowing through tubing were used to conserve gas, reduce the high gas-oil ratio and prolong the flowing life. It

Jan 1, 1930

By John J. Croston

In the closing months of 1936 the copper industry gave every evidence that it was at last on the threshold of an improved era. At the beginning of the year prices stood at 91/4c, which in itself was a great improvement over prices prevailing for the three previous years. Industry generally was showing signs of moving forward in this country, and business was definitely good in certain foreign quarters. The threat of war and preparations for rearmament in Europe and Asia acted as a further stimulus to purchasing. By midsummer the situation had so improved and stocks had been so reduced that the cartel of foreign producers (including American producers with foreign mines) decided to increase the production quota to 75 per cent on Aug. 1. Large-scale buying gave continued strength to the price and by Oct. 1 the quota was increased to 80 per cent, and again on Oct. 15, to 85 per cent. Notwithstanding this the price of copper continued its advance and on Nov. 1, with stocks declining continuously, the cartel increased operations to 95 per cent, then to 105 per cent on Nov. 5. In the meantime the domestic producers, because of the great increase in home consumption, had increased their production by nearly one-half. At the close of the year copper sold at 126 per pound, and since the turn of the present year has reached 17c. This rapid increase has not been wholly justified. Much of the increase was due to the legitimate demands of recovering industry, but rearmament orders plus accumulation of reserve stocks in case of war, purchases in anticipation of labor strikes and purely speculative activities on the London Metal Exchange accounted for the balance. Certainly in view of the state of industry and the general world price level, it appears unnecessarily high. Talk of a copper shortage is sheer nonsense, the recent condition in the market being created by overbuying, leaving but a small volume for speculative supplies. It takes some months for an increase in mine output to reach the market, but production is again overtaking apparent consumption, stocks have begun to increase, and this, together with the reopening of many small

Jan 1, 1937

By O. J. Huber

HYDROGEN effects in titanium alloys have been the subject of extensive research in recent years. Lenning, Craighead, and Jaffee1 showed that hydrogen embrittles a titanium and, at the same time, elevates the temperature at which the transition from brittle to ductile failure occurs during impact testing. In later work: the same investigators concluded that several all-ß alloys tolerate large amounts of hydrogen without serious damage to mechanical properties, but two-phase alloys suffer varying degrees of embrittlement, depending upon the specific ß-stabilizing addition used and whether or not an a stabilizer is also present. The mechanism of hydrogen embrittlement has not been clearly established. Strain rate has been shown to be an important factor and, therefore, a strain-aging phenomenon is suspected to cause the effects that hydrogen has produced on mechanical properties.3-5 Ripling6 has pointed out that ductility damage varies inversely with strain rate in a-ß alloys and directly in a alloys. This effect in a alloys can be associated with transition-temperature behavior, but the embrittlemeat mechanism in two-phase alloys remains in question. During the course of research conducted for the U. S. Air Force, a dark-etching phase has been observed at the grain boundaries of certain two-phase titanium alloys after duplex (solution plus aging) heat treatments.5-7 An example of the dark-etching interface phase is shown in Fig. 1. Decrease in ductility accompanies the appearance of the minor phase but has not always been attributable solely to the presence of the phase. Although the dark-etching phase has been observed in alloys under a rather narrow range of heat-treatment conditions, it is of general interest since it is always associated with the presence of hydrogen. The known embrittling effect of hydrogen makes any facet of its behavior of particular importance. The intergranular phase has been observed in titanium-base alloys with relatively high amounts of the ß-stabilizing elements. Specific examples of such alloys include Ti-5 pct Mn-2.5 pct Cr, Ti-3.5 pct Cr-3.5 pct V, Ti-8 pct Mn, and Ti-3 pct Mn-1

Jan 1, 1958

By F. N. Ward, E. H. Bailey

Camp and sample-site methods useful for determining about 0.5 to 16 ppm of mercury in soils and rocks have been devised to complement the analytical methods already widely used in geochemical prospecting. In the camp-site procedure the sample solution is obtained by digesting the finely powdered sample with hot nine-molar sulfuric acid and bromine, the latter generated in place. The solution is buffered at a pH of 4 and the mercury is extracted into a relatively small volume of an organic solvent. Estimations are made by comparing the color of the mercuric dithizonate extracted from the sample with that extracted from a standard. In the sample-site method the mercury is volatilized as the iodide and the latter is dissolved in a buffer solution from which the mercury dithizonate is extracted as in the camp-site method. The estimation is made by a similar comparison with standards or by comparing the color of the mercuric dithizonate with artificial standards prepared from Orange II, an azo dye. Except for the establishment of standards, the time required by an experienced analyst seldom exceeds 10 min for a camp-site determination and 5 min for a sample-site determination. Camp-site determinations are useful for commodity studies and intensive exploration programs; sample-site determinations are applicable to extensive and reconnaissance-type geochemical prospecting programs. The results obtained on samples taken along traverses above known mercury ore deposits in the California Coast Range and western Nevada demonstrate the usefulness of both methods in geochemical prospecting. The increasing use of the mercury content of soils, rocks, plants, or water in geochemical prospecting emphasizes the need for analytical methods which are sensitive and at the same time require a minimum of readily available equipment. Sensitive methods based on the absorption of ultraviolet light by mercury vapor are common in the literature31 12. Although none of these methods have been used to analyze the large number of samples required in geochemical prospecting, they could be extremely useful except for the expensive instrumentation usually required to make the methods quantitative Also, such methods are perhaps too sensitive for field use, especially around areas of possible contamination. Other methods involve the distillation of mercury from a relatively large sample and subsequent collection of the vapors in nitric acid6. The mercury is then estimated by titration with a suitable reagent such as thiocyanate. These methods are not trace methods because the actual amount of mercury measured is often as great as 50 to 100 milligrams. Also, such methods are unsuitable for geochemical prospecting because of the amount of equipment necessary and the time required. Still other methods involve colorimetry, and the sensitive reaction between dithizone and mercury (11).. is the basis for a number of reports on the determination of mercury in biological materials 5,7. Moreover, by the judicious use of solvent extraction and suitable complexing agents, the dithiaone method can be made almost specific for mercury. However, none of the dithizone methods have yet been applied to the determination of mercury in soils and rocks. In most colorimetric methods he sample solution

Jan 1, 1961

By B. M. Larsen, T. E. Brower

IN two previous papersl,2 dealing with the carbon-oxygen reaction, and the simultaneous content of each, in liquid steel in the furnace, we have made use of the quantity 0[O], defined as the excess oxygen beyond what would be in equilibrium with carbon then present if the pressure of carbon monoxide were I atm,; that is, if [C] X [O] is taken as 0.00222, 0[O] = [O] - 0,00222/[C] where [O] is the percentage of oxygen by weight as measured by the method described earlier.' This quantity 0[O] proves to be substantially independent of carbon content over the range 0.08 to 1.2 per cent, as well as of the basicity of the slag, and is nearly always within the limits 0.015 to 0.025 per cent when the bath is boiling normally and is in what we have termed a steady state. Apparently it must be at least about 0.014 per cent before boiling occurs; but this threshold value seems to depend upon the ease of bubble formation at the metal-hearth interface, hence upon the condition of the surface of the hearth. In any case, 0[O], on the average, changes considerably following any disturbance of the bath, as by addition of ore. The present paper deals with the average changes in ?[O] level following addition of Spiegel or crop ends, or after procedures to promote stirring, or by tapping of the steel from the furnace. The observations were made on a large number of commercial heats, and consequently are subject to the influence of various disturbing factors; the results have the compensating merit of showing the consistency obtainable under the limitations imposed by practical operation. VARIABILITY OF EXCESS OXYGEN IN NORMAL OPEN-HEARTH OPERATION The preceding general statements refer to the average value of ?[O] particularly in heats that are boiling actively; on individual heats, which are less active, there may be a variable time lag between the disturbance and its effect, which complicates the interpretation of what is going on. For instance, if in the normal refining process boiling is sluggish, the slag usually is gaining oxygen from the gas phase above it, or from added ore, faster than it is losing oxygen to the metal; yet when the bath starts to boil vigorously, the opposite condition may prevail for some time. The consequence of this lag is a variation of ?[O], the interpretation of which in a single heat may not be immediately obvious, This condition is illustrated in Figs. I and 2. In Fig, I, ?[O] at the beginning of the test period was near the lower limit of its usual range (dashed lines) in the steady state as a consequence of the lime boil, which had ended about as indicated. The bath is now cold, carbon drop is slow, and the first small ore feed causes only a small rise in 0[O]; as the temperature rises and as lime dissolves in the slag, and the bath becomes more active, the

Jan 1, 1946

By E. P. Mathewson

The experiments described in this paper were made at the Washoe Reduction Works, Anaconda, Mont., for the purpose of determining the relative speed of elimination of the iron, sulphur and arsenic during the process of bessemerizing copper-mattes. The samples were taken from a horizontal a barrel" converter, 8 ft. in diameter and 12 ft. 6 in. long, having an average charge of 9 tons of matte, and blown with a 16-lb. air-pressure. All samples were taken with the blast on, turning the converter from its normal blowing-position to nearly vertical, so that a conical mold, with a long handle attached to a horizontal rod, could be introduced from a platform above the converter into the mouth of the converter and a sample taken. The difficulties of taking a sample with the blast on are apparent, and the irregularities of' the lines in Figs. 1, 2 and 3 can be readily accounted for by the amount of slag in the samples. On the whole, the plotting of the results gives comparatively uniform lines, considering the conditions. The samples were taken by the regular sampling-force of the works at 10-min. intervals, as shown in Tables I., 11. and III., which also give the chemical analysis of the samples so taken. The test shown in Table I. was made with a new converter; that of Table 11. with a converter that had made three charges and had been cleaned out; that of Table 111. with a converter that had blown one charge to white metal, and had then been " washed " out and used for the test. In plotting these results, it was necessary to take, as a basis, the percentage of copper in the samples. This basis does not exactly represent the true condition, since the volume is constantly decreasing and a certain quantity of copper passes into the slag, but it is as near as can be obtained in practice. Take, for instance, in Table I., the sample No. 5, which shows: Cu, 59.9;

Jan 1, 1908

By Richard Henry Lee

Since the economies in the blast furnace resulting from enriching iron ores are so great, much attention has been paid during the past few years to the various methods of concentrating lean ores, and, as the concentrated ore is usually of extreme fineness, various methods of agglomeration and sintering, of more or less value, have been put into operation. The resulting agglomerated concentrates are generally obtained in the form of briquettes or nodules. The briquettes naturally divide themselves into two classes: (1) those made by the mixture of some binding agent, and then formed into briquettes under great pressure; and (2) those made by sintering the concentrates, the latter either being formed into bricks before exposure to heat or the sintered mass broken into fragments afterward. Of the first class I will not speak, as they are not used on an extensive scale in this country. The second class of briquettes, or those made by sintering, are simply masses of melted or fused silicate and oxide of iron mingled with more or less silicates of aluminum, lime, and magnesia. The fact that the material in a briquette is sintered is proof positive that there are no pores in the material. There are, however, quite a number of holes of greater or less diameter through the gubstance of the briquette. They are not pores in the common acceptance of that term as applied to ores by furnacemen, as the ides of the holes and channels are fused. In reality the material is simply mill cinder. It is practically untouched by the gases in the upper part of the furnace, and the iron has to be reduced by solid carbon in the boshes and hearth. Briquettes sometimes show a little saving in fuel in the furnace over an ore mixture of large lumps, but that saving is made simply because, owing to the numerous holes and channels through the mass, the briquette is practically composed of numerous small or fine lumps, and, as is well known, the finer the

Jan 1, 1914

By Arnulf Muan, R. W. Taylor

Activities of iron in Fe-Pt alloys have been dctermined by equilibrating mixtures of platinum metal and iron oxide at known oxygen Pressures in a thermobalance at 1300°C. Conzpositions and iron activities of the oxide phase at equilibrium are known from previous work, and compositions of the Fe-Pt alloy phase formed at equilibrium were detcvt?zined from the observed weight changes of the samples. The activity curve obtained shows a strow negative deviation from Raoult's law. THE present investigation was undertaken as part of a research program dealing with phase equilibrium relations existing among the oxides of iron and titanium at 1300°C. At low oxygen pressures of the gas phase in equilibrium with these oxides, the iron activity of the system is high, and considerable alloying of iron with the platinum used as a container material takes place. Thermodynamic data for Fe-Pt alloys at 1300°C are needed in order to evaluate quantitatively the extent of such reactions. Larson and chipmanlhave determined activities of iron in Fe-Pt alloys at 1550°C by equilibrating platinum metal with CaO-iron oxide-SiOzmelts in which the iron activities were known. Compositions of the resulting Fe-Pt alloys were determined by chemical analysis. Mundiath and Gerassimov2 have studied thermodynamic properties of Fe-Pt alloys by electromotive force measurements in the temperature range 550" to 1000°C. The experimental method used in the present investigation is a slight modification of that used by Grube and Ratsch3 in studies of NiCr-alloys. 1) EXPERIMENTAL METHOD 1) General. Mixtures of platinum metal and iron oxide were equilibrated at 1300°C in atmospheres of known oxygzn przssures, and the course of the reactions was followed by measuring the weight changes of the mixtures. The principles involved in the derivation of composition-activity relations from these measurements are illustrated by the composition triangle for the system Fe-FeZO3-Pt shown in Fig. 1. Take as an example a mixture of FeZO3 (hematite) and platinum such that the total composition is represented by point T. If this mixture is heated to 1300c in air (poz = 0.21 atm) and the oxygen pressure is then reduced gradually, the oxygen content of the oxide phase decreases and increasing amounts of iron enter the metal phase. As the oxide phase and the metal phase for all practical purposes are insoluble in each other, their compositions are represented by points moving toward Fe along the joins Fe-Fe,03 and Fe-Pt, respectively. The total composition of the mixture during this process also changes, but only with respect to oxygen content, because the vapor pressures of iron and platinum are negligible at 1300°C. Hence the change in total composition is described by a straight line (constant Fe/Pt ratio) radiating from the 0 apex of the composition triangle Fe-Pt-0, of which the triangle in Fig. 1 is a part. Only one such line ("oxygen reaction line", T-T",) is shown in Fig. 1. The total composition of the alloy-iron oxide mixture at any instant must, in addition, be located on the straight line (conjugation line) connecting the two points representing the compositions of the two coexisting phases. It therefore follows that the total composition of the mixture at any instant is represented by the point of intersection between the conjugation line and the oxygen reaction line. An example of the situation prevailing at a chosen oxygen pressure, po2, is shown in Fig. 1 by points a' (alloy composition), b' (oxide composition) and T' (total composition). Point b' is known from the work of Darken and Gurry,4 and point T' is experimentally determined by the observed weight change of the mixture (distance T-T). Hence, point a', the composition of the alloy, is determined from the above data as the intersection between the join Pt-Fe and the extension of the straight line bl-7'. The activity of iron in the alloy at equilibrium is identical to that of the iron oxide phase, if the same

Jan 1, 1962

By M. E. Nicholson

The solid solubility of boron in iron has been determined by saturating iron with respect to FeyB at several temperatures from 870° to 1135 C. In alpha iron the maximum solubility was found to be 0.002 pct B and in gamma iron the solubility varied from 0.001 pct at 915°C to 0.020 pct B at 1165OC. The eutectic and peritectoid temperatures were found to be 1165° and 911 °C respectively and the gamma iron solidus was located approximately at 0.020 pct B. RECENT investigations of boron-treated steels', ' indicate that the solubility of boron in austenite is of the order of 0.003 pct at 900°C. This has led to the general belief that the solubility of boron in a and r iron is considerably less than that indicated by Wever and Muller." Therefore the solid solubilities of boron in a and r iron have been re-determined. The eutectic and peritectoid temperatures were also remeasured and the r-iron solidus was studied in some detail.* In 1929 Wever and Miiller investigated the phase equilibria of Fe-B alloys. Fig. 1 shows the solid solubility region of the Fe-B diagram based on their investigation. They found that boron lowered the A, transformation temperature to 1381 °C where saturated 6 solid solution "which must contain about 0.15 pct B" and "r solid solution containing about 0.10 pct B" are in equilibrium with liquid containing 1.9 pct B. At the eutectic temperature of 1174"C, 7 solid solution was found to contain "about 0.15 pct B." A peritectoid relation was found to exist between a and y iron with an invariant temperature at 915 "C, where the boron solubility in 7 iron was "about 0.10 pct B" and the solid solubility in a iron "did not exceed 0.15 pct B." Although most of their

Jan 1, 1955

By Walter W. Bradley

Mining by hydraulic process of the important gold-bearing gravels of the Sacramento Valley in the basins of the Yuba, Bear and American rivers began in 1853, and continued at an ever-increasing rate for 30 years. In its most active days it reached an annual production of $15,000,000, and averaged $10,000,000 per year over the 30 years. During that period no provisions were made to prevent the debris from being discharged into the water courses, and ultimately large quantities of silt, sand and gravel were washed down to the lower valleys; filling channels, causing overflow of agricultural lands and difficulty in maintaining navigable depths in the Sacramento River. Agitation and suits filed because of these damages finally resulted in the injunction decision of Judge L. B. Sawyer,' in the U.S. Circuit Court, Jan. 23, 1884, which closed down practically all hydraulic mining operations not having means to restrain their debris. In 1893 (approved March 1, 1893), Congress passed the act introduced by Representative Anthony Caminetti, of California, creating the California Debris Commission, composed of three officers assigned from the Engineer Corps of the U.S. Army, and since that time it has been legal and possible within the drainage systems of Sacramento and San Joaquin rivers to conduct hydraulic mining of gold-bearing gravels behind dams built under this commission's permit and supervision. In the watersheds of the Trinity and Klamath rivers, which flow directly to the Pacific Ocean and do not affect navigation or agriculture, operating permits from the California Debris Commission are not required. There is a measure of restriction there, however, through what is known as the Trinity and Klamath River Fish and Game District. Chap. 215, Stat. 1931, in order to secure relatively clear water for the fishing season, provides that between July 15 and October 15 each year there must not be discharged into these rivers debris that will cause a turbidity greater than a content of 50 parts per million in the

Jan 1, 1937