Search Documents

By C. M. Schwartz, A. P. Young

ZIRCONIUM is noticeably embrittled at room temperature by hydride precipitate not only in notch-impact tests but also in tensile-impact tests.' The embrittlement in slow-strain tensile samples is much less severe. To understand better the relationship of the hydride precipitate to the strain-rate effect in tensile samples, the surfaces of chemically polished zirconium tensile samples strained at a slow rate (0.03 in. per min head speed) and at an impact rate (18.1 fps hammer speed) were examined in the light and electron microscopes. Vacuum-degassed samples and hydrogenated samples (100 ppm hydrogen) were examined. The hydrogenated samples were slow cooled from 800°C. The most apparent difference between slow-strain and impact tensile samples was the preponderance of twinning over slip in impact samples as opposed to relatively little twinning in slow-strain samples. The twin bands in hydrogenated samples often terminated on hydride needles as seen in Fig. 1. Almost opposite the twin terminus is a fine crack and a nearly round fissure. Holes near the areas where single lens-shaped twins or opposing pairs terminate on hydride particles also could be seen In the light micrbscope. Quite frequently, microcracks associated with a partial row of hydride particles were visible, as in Fig. 2, indicating that the crack was parallel to a row of hydride particles. Some samples were chemically polished after straining to remove metal with a minimum of disturbance of internal voids. Fig. 3 shows a crack in the interior of a hydrogenated impact sample. Holes along grain boundaries were seen after impact in both degassed and hydrogenated samples. Very few microcracks were seen in degassed samples after impact or slow strain, or in hydrogenated samples after slow strain.

Jan 1, 1959

By E. G. Leonardon, C. Schlumberger, M. Schlumberger

In the search for practical geological problems amenable to solution by the potential methods, the geophysicist is led to study mathematically various theoretical cases. In these idealistic discussions, the media under consideration are generally supposed to be homogeneous and iso-tropic. The geophysicist, of course, realizes perfectly that these conditions do not occur in their entirety in reality. However, the assumptions made are justified, because very often they are necessary in order to render possible an exhaustive study of a given problem, which otherwise would be too complicated, and would not lend itself to a complete mathematical analysis. Of the above two assumptions, that concerning the homogeneity of a given geological formation is satisfactorily realized except in so far as isotropy is concerned, since this property is not often encountered in practice. As a consequence, it is very desirable for the geophysicist to have quite an extensive knowledge of the properties of anisotropic formations, and of the laws that govern the propagation of electric current therein. With such principles in mind, he will be able to decide whether the conclusions arrived at in simple, isotropic conditions are still correct in more complex cases, or in what way they must be modified or adapted in order to constitute a sound basis for the interpretation of the results obtained in anisotropic media. On the other hand, the fact that in anisotropic formations the mobility of the ions is greater along the strike than perpendicular thereto can be utilized for determining the direction of the dip by induction measurements. We therefore propose to study in three successive chapters the following points: 1. Propagation of the electric current in anisotropic media. 2. Some consequences of the anisotropy of geological formations with reference to the surface electrical measurements, and their interpretation. 3. Determination of the direction of the dip of anisotropic formations by surface induction measurements.

Jan 1, 1934

By G. Sherburne Rogers

One of the features of oil-field work that puzzles operator, chemist, and geologist alike, is variation in the gravity of the petroleum produced on neighboring leases or even from adjoining wells. Few fields in the United States yield oil that is of uniform gravity throughout; in some fields the different grades are produced from different sands, in a few from different formations, and in many from different areas in the same sand. In a few cases, perhaps, a common assumption—that the heavier oil is derived from the lighter through the escape of the more volatile constituents—is valid, but many cases can not be explained in this way. Although in the California fields the specific gravity of the oil generally decreases with depth, there are numerous exceptions to this rule; and, as in many other regions the light oil is found nearest the surface, it is evident that evaporation underground is generally an unimportant factor. It is generally recognized that the great differences between petroleum from widely separated fields are due largely to differences in age and degree of metamorphism and to variation in the composition of the original organic matter; but in the writer's opinion some of these broader differences, as well as most of the minor variations in the character of the oil from any one field, are due to the local action of natural reagents such as sulphur or oxygen. This is particularly likely to be true if the oil has migrated from one formation to another, as in the California fields; and in some arcas it appears that variation in sulphur content may even afford a rough index of the extent or distance of the migration. It is the purpose of this paper to call attention to the chemical action of sulphur and oxygen on petroleum, to show that the gravity of the oil from any one field is intimately related to its sulphur content, and to discuss the possi-

Jan 1, 1918

By G. St. J. Perrott

One of the important hazards in coal mining is the danger of ignition of explosive mixtures of methane and air or coal dust and air, or both, by the explosives used in blasting the coal. It has long been recognized that certain explosives are more dangerous than others in this respect. ' In America and abroad, government testing stations have been established for officially passing on the suitability of explosives for use in coal mines. In this country the Federal government is given no power to enforce the use of the approved explosives but merely publishes from time to time, through the Bureau of Mines, those explosives which have passed the tests necessary to place them on the list for use in coal mines. In spite of this lack of police power, the increase in the use of permissible .explosives since the promulgation of the fist list in 1909 has been rapid. In 1912, only 8 per cent. of the explosives used in coal mines were permissible; in 1925, this figure had increased to 25 per cent. While the past record of permissible explosives has been most gratifying, it is very desirable that we pave the way for further improvement in explosives and blasting methods by learning more about the mechanism of ignition of gas and coal dust by explosives. To this end a considerable amount of investigative work already has been carried out and a large amount yet remains to be done. It is the purpose of this paper to discuss briefly the effect of the characteristics of explosives and method of loading in the borehole on the liability of a blown-out shot to ignite explosive mixtures of gas or dust. For an account of the methods by which an explosive is tested for permissibility for use in coal mines, the reader is referred to Schedule 17-A of the U. S. Bureau of Mines. Safety Factor in Using Explosives The factors that affect the liability of an explosive to ignite gas or dust are already known in a qualitative way but quantitative data are

Jan 1, 1927

By T. T. Chen, P. Pint

Based on the mineralogy, phase characteristics and compositions of the smelter feed, the smelter products and the smelter wastes, the sources and distributions of mercury and arsenic in the Afton copper smelter, Kamloops, British Columbia have been determined. Of the total mercury In the feed, approximately 33% is in solid solution in tennantite, 51% is in native copper and 16% occurs as mercurian silver. Arsenic in the feed occurs mainly as tennantite. Under current smelting conditions, 99.6% of the total mercury In the feeds enters the off-gas cleaning system. From this off-gas, about 1% of the total mercury, occurring as dust, is recirculated to the flotation concentrate; 4.6% of the total mercury is contained in SO2 scrubber sludge which is discharged to tailings. Approximately 78% of the total arsenic in the smelter reports in the copper products; 20% is incorporated in the dust and slag which are subsequently recirculated to the mill. Only 1.8% is rejected as scrubber sludge, and less than 0.2% 1s released to the mercury scrubber.

Jan 1, 1984

By R. A., D. L. Sponseller, Flinn

Using specially del'eloped titanium nitride crucibles and a pressurized syslem, it has been possible to determine the solzibilitv of liquid calcium in liquid iron and iron-base alloys. At 2925°F the solubility is 0.032 wt pet Ca in pure iron. The solubility is increased by aluminum, carbon, nickel, and silicon additions, and lowered by additions of gold. An inflection in the calcium-solubility curve occurs as carbon is added to iron. At approximately 0.87 Wt pet Ca the CaC, phase replaces liquid calcium, and the calcium concentration de- creases as more carbon is added to the iron. The maximum solubility, 0.36 wt pet Ca, was obtained in iron containing 10.5 wt pet Si. The data have important implications regarding the use of calcium in process metallurgy, as well as providing an interesting test of theories of metallic solutions. Reasonably good agreement is found with theories of Alcock and Richardson and of Wagner, and criteria are suggested which permit these theories to be applied more readily to systems of this type. AT the present time relatively little is known about the factors influencing solubility in liquid metals. Information of this type is important for such matters as the control of impurity levels in liquid metals, the use of magnesium in ductile-iron production, and the use of liquid-metal alloys as fuels and coolants in nuclear power plants. One important example of restricted solubility concerns the extent to which liquid calcium will dissolve in liquid iron. This is a matter of considerable interest in view of the strong potential of calcium for removing certain impurities in steel,. as well as the ability of calcium to desulfurize, inoculate, and produce spheroidal graphite in cast irons.' Since ferrous materials normally contain other elements in addition to iron, the interactions of third elements with the Fe-Ca system are of interest. In view of the foregoing, this investigation was conducted to determine the solubility of liquid calcium in liquid iron and the effects of various third elements upon the solubility. For reasons of theoretical and engineering importance, the elements investigated were aluminum, carbon, gold, nickel, and silicon. Numerous attempts were made in the early part of the present century to determine the solubility of calcium in both liquid iron and steel, employing a variety of open-melt and closed bomb-type systems.2-4 From the results of these tests Wever concluded that calcium is insoluble in liquid and solid iron.5 These investigations were unsatisfactory in that they failed to insure the presence of a liquid layer

Jan 1, 1964

By J. W. Rutter, K. T. Aust

THE object of the experiments to be described in this report was to determine, first, which grains, out of a large number introduced into a sample in which their growth could proceed, were able to grow most successfully; and, second, the factors which control their growth selection. In an earlier study of grain boundary migration in high-purity lead,' it was found that, under some conditions, the most successful grain in an experiment of this type bears a special orientation relationship to the grain into which it is growing. The present work represents an extension of the previous study, directed at the determination of the orientation relationships which appear under a wider variety of conditions. Experiments of this general type have been done using commercial aluminum2 with somewhat conflicting results. In the present experiments, in contrast to the above,' the sample composition was a principal controlled variable, resulting in a considerable clarification of the phenomena observed. EXPERIMENTAL TECHNIQUE The experimental technique used in this investigation was essentially that employed previously in studies of grain boundary migration kinetics.1'3 The material used was zone-refined lead with various small amounts of tin or silver added to study the effect of varying the sample composition. The specimens were in the form of single crystals, about 1/4 in. 1/4 in cross section by 3 to 4 in. in length, grown from the melt in a horizontal graphite boat. A crystal grown in this way generally contained a lineage or "striation" substructure of the type shown in Fig. 1 of Ref. 1. This substructure consists of an array of low-angle boundaries which partition the crystal into regions misoriented from each other by a few degrees. The substructure constitutes a source of driving energy, estimated to be about 4000 ergs per cc, for the migration of a large-angle grain boundary into the striated crystal. New grains were introduced by plastic deformation in compression of a localized reglon at one end of the sample. Re-crystallization occurs at room temperature in the deformed region, introducing a large number of new, striation-free grains into the specimen. These grains are able to grow into the melt-grown crystal on annealing at a suitable temperature. The stria-tions are removed by passage of the grain boundary, as the substructure energy is utilized to produce the boundary migration. Usually, only one or two of the recrystallized grains persist after growth has occurred for about 1 cm out of the deformed region. Laue back-reflection X-ray photographs were obtained to determine the orientation relationship between the melt-grown crystal and the recrystallized grain or grains which grew most successfully in each specimen. EXPERIMENTAL OBSERVATIONS Fig. 1 shows the results obtained for a series of specimens to which had been added tin in the range from 0 to 5 ppm by weight. In this figure is plotted, in the standard stereographic triangle, the single axis about which the most successful recrystallized grain or grains are related to the starting, melt-grown crystal by the smallest rotation. The range of angular rotations observed about such axes is indicated beside each stereographic triangle. The results shown in the stereographic triangle on the left, Fig. l(a), were obtained by localized deformation at one end of each specimen at room temperature, followed by annealing in a furnace which had been preheated to 300°C. The furnace atmosphere was argon. It will be seen that the orientation relationships observed between the melt-grown and recrystallized grains are quite random. On the right, Fig. l(b), are shown results for samples in which the de-

Jan 1, 1961

By Henry S. Rawdon

The structure of wrought iron as usually described by metallographists and workers in metal in general is that of a fairly pure iron. Impurities, if present, are usually considered as being in solid solution in the crystals of the ferrite matrix or as forming part of the ever present "slag streaks." Attention is herein directed to one type of these dissolved impurities; to the detection of such impurities, particularly in low-grade irons, and to their possible influence on the physical properties of the metal. The attention of the Bureau of Standards was first directed to wrought iron of the peculiar and unusual characteristics to be described later, in material which had failed in service and was submitted for test. The examination was extended to other grades of wrought iron, to see whether such features are of common occurrence in this class of material. MICROSTRUCTURE OF WROUGHT IRON Usual Structure The general microstructure of wrought iron is so well known that a detailed description of it here is needless. There is shown in Fig. 2 the structure of a sample of Swedish iron which illustrates well the matrix of ferrite crystals in which are embedded the slag threads so characteristic of the puddling process and the subsequent working of the material. The usual commercial product contains varying amounts of the impurities commonly associated with iron and steel, i,e,, manganese, phosphorus, silicon, and sulphur together with small amounts of carbon. Of these, the larger part of the phosphorus and some of the silicon present are held in solid solution in the ferrite while most of the remaining impurities, other than carbon, exist in the in closures of slag. Aside from the discontinuities introduced by the slag streaks the ferrite matrix has the microstructure and appearance of a pure metal. No definite orientation of the various crystals or grains is apparent; deep etching of the specimens reveals no intracrystalline features (i.e., within the grains) other than those noted in " pure " metals in general (etching pits).

Jan 1, 1918

By D. A. Stevenson, T. Alden, J. Wulff

A portion of the liquidus curve has been determined for the binary alloy systems Ni-Pb and Cr-Pb. The solubility of nickel is 0.53 atomic pet at 372° and 18.63 atomic pet at 1200°C. Chromium shows low solubility, 0.634 atomic pet at 1210°C. Molybdenum and tungsten were also studied and found insoluble in lead, less than 0.005 atomic pet at 1200°C. INCREASED use of liquid metals of low melting X point for heat transfer, coating, joining, and other purposes has renewed interest in the solubility of structural metals in these liquids. A study of Hansen1 and current literature indicates that few liquidus curves at the low melting end of the binary diagrams have been accurately delineated. This statement applies particularly to the binaries of lead. The present paper is limited to nickel, chromium, tungsten, and molybdenum in lead. In early studies2, 3 of the lead end of the Pb-Ni system, a monotectic at 1340°C was established. Tammann and Oelsen' determined the solid solubility of nickel in lead at 20°C to be 0.023 wt pet. Recently Pelzel5 determined the liquidus curve from the eutectic temperature of 327° up to 727°C using a segregation method. In the present paper this part of the curve has been checked and extended to 1244°C. The Pb-Cr system was first studied by Hindrichs.6 He pointed out the existence of a monotectic at 1470°C and indicated a tentative liquidus. Recent corrosion studies of Fe-Cr alloys in lead suggest that chromium is more soluble than iron in lead.7-8 The solubility of tungsten in lead according to Inouye8 is about 30 wt pet at 1200°C. Appreciable solubility of molybdenum in lead might therefore be expected. Experimental Various experimental techniques have been employed in the determination of solubility in liquid metals. For low solubility, thermal analysis is unsatisfactory. A segregation method was used by Pelzel3 in his study of the Pb-Ni system. In this procedure separation of liquid and solid is possible due to difference in density. In the technique of Kleppa10 a single piece of material is maintained in contact with the liquid metal in evacuated Vycor vials. After equilibration, solid and liquid are separated by tilting. Keck and Broder" measured the weight of a piece of the solid solute before and after immersion in a pure solvent bath; the weight loss was a measure of the solubility. All of the above procedures are time-consuming since they permit only one determination per run. Numerous samples for analysis may be taken from the melt in the method described by Gurinsky and CO-workers.10 The rate of extraction of samples is limited only by the time required for equilibration. In the present work, a modification of this method was employed. A 150-g charge of analytical reagent grade lead and the added metal* were contained in an Alun- dum crucible. It rested on firiely divided silica at the closed end of a 45 mm Vycor tube, 500 mm long. The top of the tube was provided with an inlet and

Jan 1, 1959

By Frank H. Macpherson

Few people realize the tremendously important part that Saline and Pulaski Counties in central Arkansas have played in the winning of the war The present favorable war situation might have been very different if we had not had the bauxite produced during the past two years from these two small areas, a total Of about 15 square miles. As a general statement, it can be said that the Arkansas bauxite deposits are, individually, relatively small, irregular in thickness, somewhat scattered and, therefore, compared with coal or iron-ore or open-pit copper deposits, relatively ill adapted to a rapid and drastic expansion in output. A few years ago it would have seemed an impossibility for these two counties to produce over six million long dry tons of bauxite in one year. However, with the cooperation of the operators, that is what happened in 1943, when the state of Arkansas achieved the seemingly impossible with a production of 6,020,684 1 long tons (dried equivalent) of bauxite ore during the calendar year, compared with an average annual production of 323,7252 tons in the period 1931 to 1941. It became apparent early in the year '94' that the united States soon might be drawn into the war, and, therefore, that an immediate study of the domestic metal situation was necessary. Aluminum is by far the most important metal used in the manufacture of aircraft and many other implements of war and it was evident that there would have to be a tremendous increase in the domestic production of bauxite, which is practically the only present source of this metal. AS more than 95 per cent of the known bauxite reserves of the United states was in Arkansas, careful preliminary studies were made in that state by representatives of the united States Bureau of Mines, the United States Geological survey and the War Production Board in the summer of 1941 Reserves in other states also were studied. The result of these studies was a recommendation by the War Production Board that mining in the bauxite.producing areas of Arkansas be geared for maximum production, in order to supply sufficient ore for this country's war requirements and, if necessary, to supply the war needs of Canada as well. The annual goal of eight million long tons (dry weight) set for Arkansas by the war Production Board was exceeded in 1943, when in August the output reached a rate equivalent to more than 8,300,000 long tons, dry basis. Because of the comparatively small tonnage of bauxite reserves, Congress appropriated funds for an extensive drilling program to be carried out by the Bureau of Mines in cooperation with the Geological Survey. Drilling began in May 1942 but owing to delay in delivery of drills, and trucks upon which the drills were mounted the program did not get into peak operation until early in 1943. By the end of July 1944, the Bureau of Mines records indicated an addition to the Arkansas reserves of 10,000,000 long tons (wet basis) in place,

Jan 1, 1946

By R. C. Buehl, J. P. Morris

ACTIVITY values for sulphur dissolved in liquid iron and slags as functions of composition and temperature are needed in applying thermodynamics to sulphur-control problems in iron- and ' steel-making. The purpose of this investigation was to determine the effect of carbon on the activity of sulphur in the metal phase. The method employed was the same as that used in an earlier investigation' concerning the effect of silicon on sulphur activity in liquid iron. A study was made of the conditions of equilibrium in the reaction between hydrogen gas and sulphur dissolved in iron-carbon alloys. The chemical equation for this reaction can be written as follows: S (in liquid Fe-C alloy) + H2 (gas) = H2S (gas). It was found that the activity coefficient of sulphur in liquid iron increases as the carbon content increases. At 2.3 pct carbon and 1600 °C, the activity coefficient of sulphur is twice its value in carbon-free iron, and at carbon saturation it is more than six times as great. The effect of temperature on sulphur activity was found to be small. Previous work on the reaction between hydrogen gas and sulphur dissolved in liquid iron has been reported by several investigators2,³,4 but only recently have studies been made of the effect of alloying elements. Silicon1 is known to have a pronounced influence on the activity of sulphur in iron, its effect being similar to that shown by carbon as described in the present report. Kitchener, Bockris, and Liber-man5 recently have published a preliminary report of their work on the effect of carbon on sulphur activity in iron. Their experiments were made at 1570°C and carbon saturation in the melt. Under these conditions they found that the activity coefficient of sulphur was approximately doubled by the presence of carbon. This is a much smaller effect than that found in the present work. Experimental Method: The apparatus and procedure were essentially the same as those used in the earlier investigation of the effect of silicon on sulphur activity.' Briefly, the method was as follows: A molten iron-carbon alloy was brought to equilibrium at constant temperature with a mixture of H2 and H2S of constant composition by bubbling the gas through the metal. Samples of the melt were

Jan 1, 1951

By R. D. Vaughn

The analysis of laminar flow of power-law non-Newtonian fluids in narrow, eccentric annuli is employed in this paper to discuss the problems of lubricant flow in journa! bearings and of errors introduced by eccentricity in experimental studies with concentric annuli on extruders and wellbore annuli. The velocity profile and pressure loss-flow rate equations are developed for the laminar flow region. In addition, the expected error in flow rate and pressure-loss measurements for concentric annuli as a result of eccentricity is determined. For example, a 10 per cent displacement of the core of an almost concentric annul us would cause a 1.8 per cent decrease in the observed pressure loss for a fluid with a power-law exponent n of 0.25. The corresponding increase in the observed volumetric flow rate would be 7. 5 per cent. INTRODUCTION Non-Newtonianism and eccentricity occur simultaneously in two engineering problems: (1) flow of lubricants in journal-bearings and pressure-reducing bushings, and (2) flow of non-Newtonian fluids in plastic extruders and wellbore annuli. The lubricants used for moving parts are often non-Newtonian in character — often they are plastic in behavior. A solution to the problem of flow of non-Newtonian fluids in narrow eccentric annuli is particularly pertinent to this problem. In all experimental studies of laminar flow of fluids in concentric annuli, such as in extruders and well casings, the error due to eccentricity must be estimated or studied. A number of publicationsl-4,6,7 have dealt with this problem for Newtonian fluids; however, I am not aware of work for non-Newtonian fluids. This work is directed to the non-Newtonian problem. Before the solution to the problem is given, the pertinent conclusions from the work on Newtonian fluids will be reviewed. Heyda 1 and Redberger and Charles 2 have published general solutions to the problem of the laminar flow of Newtonian fluids in eccentric annuli, apparently without knowing of the earlier work of Ca ld well 3 and Bairstow and Berry,4 which is reported by Dryden, et al. 5 Although several mathematical routes are encompassed by the work of these authors, the results appear to be equivalent. Redberger and Charles2 show that the error caused by eccentricity in concentric annuli is negligible for small diameter ratios (k < 0.5); however, for large diameter ratios (k + l), the error in the predicted flow rate can be as great as 100 per cent or more. Partial solutions to the problem are available from the work of Dryden,5 Tao and Donovan6 and Piercy, et a1.7 Tao and Donovan examined the case of flow in narrow, eccentric annuli (k + 1) with and without rotation of the annular core. These authors also reviewed previous work on this subject and verified their approach with experimental data. Dryden gives the solution for the limiting case of complete eccentricity or tangency. Piercy, et a l. published an early solution to the problem of narrow eccentric annular flow. The conclusions of Redberger and Charles2 and the experimental proof of Tao and Donovan6 both suggest that the region of large diameter ratios (k + 1) is of main interest and that the parallel planes approximation to the solution in this region is satisfactory. This method will now be extended to the laminar flow of non-Newtonian fluids in narrow eccentric annuli. THEORETICAL SOLUTION The geometrical aspects of the problem are illustrated in Fig. 1. To represent the non-Newtonian fluid the power-law model was selected. This model has many disadvantages which have been pointed out; nevertheless, its simplicity, its frequent and wide applicability justify its use in this work. Fredrickson and Bird8 and Savins9 have used it as a basis for a theoretical study of laminar flow of non-Newtonian fluids in concentric annuli.

Jan 1, 1966

By Louis A. Rosales, Kanji Ono

The anomalous behavior of hydrogen in iron is examined and a new model is proposed It is postulated that hydrogen single and di-interstitials are in equilibrium with each other. When the binding enthalpy of the di-interstitial, B, is assumed to be about 10 kcal per mole, the predicted temperature dependence of the solubility agrees reasonably well with the reported data. Effective diffusiuity is calculated assuming the di-interstitials to be immobile. Since the number of mobile single interstitials is greatly reduced at lower temperatures, the effective diffusivity is decreased. A good agreement in the temperature dependence of diffusivity between theory and experiment is provided with B - 10 kcal per mole. The predicted diffusivity is also a function of total concentration of hydrogen and this appears to be Partly responsible for the large scatter in the reported data. HYDROGEN is known to form an interstitial solid solution with iron.&apos;&apos;&apos; At elevated temperatures, it has been well-established that hydrogen enters iron in the dissociated form and occupies the interstices, and that diffusion of hydrogen in iron is via the interstitial mechanism. The concentration, c, permeability, P, and diffusivity, D, of hydrogen in iron have been separately determined and are consistent with each other under the steady-state condition for temperatures above approximately 400°C; that is, the relationship P = c-D holds. At lower temperatures, however, anomalous behavior of hydrogen in iron has been observed by many investigators. The results of experimental studies4-&apos;&apos; of the diffusion of hydrogen in iron are summarized in Fig. 1, in which the values of D are plotted against the reciprocal temperature. Although there is an increasing divergence in observed values of D with decreasing temperature, the values of D at temperatures below approximately 200°C are definitely small as compared with the extrapolation from high-temperature data. The lines shown bracket the region containing the most probable data. The observed values of c6," are plotted against the reciprocal temperature in Fig. 2, where the dashed lines represent Geller and sun&apos;s&apos;&apos; most probable isobars at 1 and 100 atm. At high external hydrogen pressure and low temperatures, the values of c observed are higher than those expected from high temperature data. It is generally accepted that certain trapping mechanism is responsible for the anomalies, but the nature of the trapping mechanism has not been clarified. Various types of hydrogen traps were suggested in the literature, such as "rifts" in the lattice dislocations, voids, microcracks, and so forth. However, no quantitative account of the observed behavior has been given in terms of these trapping mechanisms. Formation of methane in hydrogen-charged steel was found by ~odgurski." This appears to explain the existence of the so-called "residual" hydrogen,4 but not the observed anomalies of hydrogen in iron. McNabb and Foster&apos; proposed a mathematical analysis in terms of a trapping mechanism. However, the physical significance of the traps was not clarified. The necessity of evaluating five parameters in their theory made comparison with experiment difficult. In the present paper, a model is proposed in which the anomalous behavior of hydrogen is attributed to the formation of hydrogen di-interstitials at lower temperatures. In this model, it is postulated that single and di-interstitials are in equilibrium with each other. (The hydrogen di-interstitial is to be distinguished from a hydrogen molecule which may exist in voids.) It can then be shown that most of the anomalies can be explained by assuming that the di-interstitials are virtually immobile and that the binding enthalpy of the di-interstitial, B, is approximately 10 kcal per mole. Predictions of the theory agree with the available experimental data reasonably well. THEORY The basic postulate of the present analysis is that single and di-interstitials are in equilibrium with each

Jan 1, 1969

By A. S. Richardson

AIR conditioning, or air cooling, for the improvement of ventilation in the Butte mines has come into increasing use during the past 10 years. In part, the methods practiced have been described in previous publications of the Institute, but some improvements on earlier methods have been made and a number of new features have been developed. This paper is presented as a record of progress made, and for the sake of completeness describes all general features of the work. The need for air conditioning in the ventilation of mines in the district arises from the fact that the temperature of the ground and mine water has shown a very great increase with increase in mining depth, and has now reached a maximum of slightly over 130°F. The most difficult part of the ventilation problem is the maintenance of temperature and humidity of a satisfactory standard in the working places, especially on the lower levels. Although ordinary ventilation is adequate to maintain good conditions in most of the working places it is subject to a number of limitations at great depth. Most important among these limitations is that with increase in depth the air becomes heated before it reaches the working places, both by compression from increase in atmospheric pressure and by heat transferred to it from rock at high temperature, so that its capacity for lowering temperatures is greatly reduced before it reaches the operating zone. Increasing depth of mining also increases the distance traveled by the air in its passage through the mine, and this causes a corresponding increase in resistance to air flow, so that there is greater difficulty in maintaining even the same volume in circulation. Thus, in the face of a demand that the ventilating system have a very much greater capacity to remove heat from the mine, the tendency is for that capacity to diminish. The only evident alternatives were (I) the opening of additional air shafts to increase the volume of air in circulation, (2) an extension of the existing system that would be subject to the same limitations, or (3) the adoption of an entirely different method such as air cooling. Fortunately for an economic solution of the problem, the mean annual temperature of the surface atmosphere at Butte is about 40°F., with very low relative humidity in summer, so that there is unlimited natural cooling power at a temperature range adaptable to air-conditioning methods. METHODS Two similar methods of air conditioning are used, as necessitated by service requirements and dependent upon the equipment available. In one, which is the more important and has the greater cooling capacity, water is circulated in a closed circuit, and, alternately, first absorbs heat from warm mine air and then dissipates it in the surface atmosphere by cooling at a cooling tower. The second

Jan 1, 1941

By Peter Greenfield, Paul A. Beck

Thirty binary systems of vanadium and chromium group transition elements with second and third long period transition elements were explored in regard to the intermediate phases formed. It was found that the phases predominating in these systems are s, AB type with ordered a-tungsten or C8 structure, close-packed-hexagonal with small unit cell dimensions and, finally, phases isomorphous with 1-manganese. IN recent years, considerable information has become available concerning the intermediate phases in binary systems of the transition elements. Thus, the s phase has been found to occur in most of the binary systems of vanadium, chromium, and molybdenum with the group of elements manganese, iron, cobalt, and nickel.&apos; It was observed that, while the rr phases formed by chromium with manganese, iron, or cobalt possess a considerable temperature range of stability, particularly in the Cr-Co system, the corresponding s phases with molybdenum are limited to a temperature range of less than 400" above about 1200°C. Goldschmidt&apos; reported v phases of tungsten with iron and cobalt, and these are apparently stable only at (and above?) 1400°C." Exploratory work in this laboratory with Fe-W and Co-W alloys of approximately 60 atomic pct W annealed at 1300°C did not produce X-ray patterns suggesting the presence of a phase. It appears then that the phases of iron and cobalt with the chromium group elements decrease in stability as the two components are chosen from long periods further removed from each other. From the available information, it might be concluded that the controlling factor is the increasing difference in atomic radii between the components. In contrast to the a phase, the phases formed by iron and cobalt with chromium group elements&apos; are stable only when the latter have large atomic radii (molybdenum and tungsten); the corresponding phases with chromium do not occur. When the difference in atomic size becomes still larger (r,/r,, approaching the ideal value of 1.225), the u and p phases are replaced by Laves phases (AB,), as in the alloys of iron and cobalt with columbium," tantalum." and titanium."-" However, atomic size certainly cannot be the sole determining factor, since, for instance, in contrast to the very stable (Mo, Co)p phase, no such phase occurs in the Mo-Ni system even though the atomic diameters of cobalt and nickel are nearly the same. Similarly, chromium and cobalt form a a phase in a wide temperature range," but the corresponding s phase in the Cr-Ni system is missing. It has been shown that the composition of the u phase in various binary and ternary systems of transition elements in the first long period may be correlated in a fairly quantitative manner with the number of electron vacancies. The influence of electronic structure is probably present also in binary and ternary phases&apos; and to some extent, apparently, even in Laves phases." " Although the absence of phases in the Cr-Ni and Mo-Ni systems has not as yet been explained on the basis of electronic structure, it appears reasonable to suspect a connection. One of the great difficulties in arriving at well founded rules in regard to the alloying behavior of transition elements lies in the lack of reliable information concerning the details of their electronic structure in the metallic and alloy form. The theoretical penetration of this field appears to be beset by very considerable difficulties, even when the complications due to alloy formation are disregarded. Another great source of uncertainty is the scarcity of phase diagram information even for binary systems of the transition elements so that only a very limited basis is provided for generalizations as to the occurrence of intermediate phases. For instance, very few binary phase diagrams of second and third long period transition element systems have so far been published. The present work was undertaken in order to survey the various types of intermediate phases occurring in 30 binary systems of elements of the group vanadium, columbium, tantalum, chromium, molybdenum, and tungsten with the elements rhenium, ruthenium, rhodium, palladium, and platinum. For most of these binary systems phase diagrams are very incompletely or not at all known, as will be further reviewed.*

Jan 1, 1957

By Y. Baskin

Solid-solubility relationships in the Pseudobinary systems UAS-UP, UAs-US. UAS-UC, aid UAs-UN were investigated. The first two systems exhibit complete mutual solubility, whereas the component compounds in the other two systenzs are immiscible. The above information, together with solid-solubility data joy six additional pseudobinary systems , were analyzed for compliance wilh the Hurrze-Rothery rules for rnetallic systems. The relative size difference of the component nonmetal atoms was found to be the dopainant jactor determining the extent of solid solubility between the NaC1-type uranium compounds. The anionic and covalent radii of the nonmetal atoms appear to be inadequate for these systems, but compuled radii based on rare earth compounds yield consistent results for the uranium compounds. THE actinide elements, like metallic elements of the transition and rare earth series, readily form binary compounds with nonmetallic elements of groups IV, V, and VI of the periodic table. Of particular importance are the NaC1-type equiatomic compounds with carbon, nitrogen, sulfur, phosphorus, and arsenic. The uranium members of this family of compounds have high melting points, are essentially stoichiometric, and exhibit various amounts of mutual solubility. Thus, they are of interest for investigating the factors governing the extent of solid solubility. Previous investigators have determined the solid-solubility limits in the pseudobinary systems between the compounds UC, UN, US, and UP. Anselin et a1 .&apos; reported complete miscibility in the system UC-UN. Baskin and shalek 2 and Allbutt et a1.3 reported that UP and US exhibit complete mutual solubility. Shalek and white4 reported partial miscibility in the system US-UC. At 1800°C the maximum solubility of UC in US is 40 mol pct, but that of US in UC is 4 rnol pct. shalek5 found limited solubility in the system US-UN; the maximum solubility of UN in US is 11 rnol pct at 1800°C, while that of US in UN is only 0.3 mol pct. White and askin 6 found very limited miscibility in the system UP-UC at 1800°C. Approximately 7 mol pct UC is soluble in UP, but there is no solubility of UP in the monocarbide. Phase relations in the pseudo-binary system UN-UP were investigated by askin.&apos; Approximately 0.7 mol pct UN is soluble in UP at 1800°C, while UP is immiscible in UN. The present study was carried out to explore the extent of terminal solubility in the systems UAs-UC, UAs-UN, UAs-US, and UAs-UP. This information, combined with existing data, provided a sufficient basis on which to determine the factors governing solid solubility in pseudobinary systems containing NaC1-type uranium conpounds. I) EXPERIMENTAL 1) Materials. The compounds UC and UN were obtained from the Kerr-McGee Corp. and United Nuclear Co., respectively. The US, UP, and UAs were synthesized by reacting finely divided uranium with H2 S, pH3, or AsH3 gas at low temperature (300° to 500°C), followed by homogenization in a vacuum at moderately high temperatures (1400° to 1700°c).8-10 The materials were essentially stoichiometric, with the exception of UC, which exhibited a C/U ratio of 1.05. Oxygen was the major contaminant in these compounds, ranging from 0.05 wt pct in US to 0.30 wt pct in UC, and it was generally combined with uranium to form UO2. The UO2 content in these materials was usually of the order of 1 wt pct, and did not exceed 2 wt pct. Furthermore, no evidence was found for a high-temperature reaction between uranium dioxide and any of the compounds. Chemical analyses of equilibrated compositions in the systems UAs-UP and UAs-US showed that the non-metal atom to uranium ratios averaged about 1.01, and that the oxygen contents ranged from 0.06 to 0.22 pct. However, the small deviations from stoichiome-try or the presence of minor oxygen impurities do not invalidate the conclusions to be drawn from this study. 2) Experimental Procedures. The component compounds in powdered from were blended in the desired proportions for 5 hr in the ball mill that consisted of stainless-steel balls in a plastic container. Chemical analyses indicated very little metallic pickup from the blending operation and virtually no increase in oxygen content. The pellets were pressed in a 0.270-in.-diam steel die under 40,000 psi pressure. One wt pct of stearic acid dissolved in CCl 4 served both as a binder and as a die lubricant. Chemical analyses revealed that the stearic acid left no carbon residue in the sintered samples. The pellets were sintered in vacuum in an unsealed tantalum crucible. The temperature, measured with a calibrated optical pyrometer, was maintained at 1800" + 30°C for 3 hr. This was sufficient time for attaining equilibrium as no change occurred in either the lattice parameters or the sharpness of the X-ray patterns when samples were annealed for longer periods of time. The pellets were cooled with the furnace. Debye-Scherrer powder patterns were taken at room temperature with a 114.59-mm-diam Norelco powder camera and CuKor radiation (CuGI = 1.5405A). Unit cell dimensions were determined from a Nelson-Riley extrapolation to the high-angle reflections. The values for were precise to k 0.001A. 11) RESULTS X-ray and met allographic investigation revealed that complete mutual solid solubility exists in the pseudobinary systems UAs-UP and UAs-US. The lattice parameter vs composition plots, Fig. 1, show a

Jan 1, 1968

By R. G. Patterson

The usual procedure in determining the magnetic susceptibilities of rocks and formations has been to take samples in the field and measure their volume susceptibilities in the laboratory, using one of numerous methods available. In none of these methods is the measuring instrument suited for field use. Usually the sample is pulverized; sometimes it is machined to a desired sue and shape, and in one method1 a cast of the sample is made and the susceptibility of the rock compared with that of a material of known susceptibility of the same size and shape, made from the cast of the original sample. Some writers assert that the difference in susceptibility of a rock sample in powdered and solid forms is negligible, and while doubtless this is true in many cases there are others in which the difference becomes appreciable. Further, the susceptibility of a small specimen may differ from that of the rock from which it is taken, owing to the stresses produced by the hammering or other forces used to obtain the sample and shape it for testing. Wilson2 found that an individual specimen of granite had about the same susceptibility in the solid as in the powdered form, but that pieces from different parts of the rock varied as much as 750 per cent because of unequal distribution of magnetite. The most accurate value of susceptibility would, obviously, be obtained from averag- ing a number of tests on the undisturbed rock instead of from one or two samples. No such procedures have been published, to the writer&apos;s knowledge. It is the purpose of this paper to describe a method by which susceptibilities of rocks may be determined in place by means of a portable instrument. Method The principle involved in this new method is that there is a change in inductance of a coil due to the presence in its magnetic field of a paramagnetic or dia-magnetic medium. In this case, however, the windings of the coil do not enclose any part of the rock under test. Instead, the coil is circular, being small in cross section as compared to its radius, and consists of several hundred turns of fine wire. It is placed flat on the rock of which the susceptibility is to be measured. Thus only part of the magnetic field from the coil penetrates the rock under test. The relation between the change in field strength or inductance of the coil and the susceptibility of the medium will be developed later. To measure the change in the inductance of the coil due to the presence of a magnetic material an alternating-current inductance bridge was chosen. Description of Apparatus Of many alternating-current bridge methods applicable,3 the one shown in Fig. 1 (Owen&apos;s bridge&apos;) was adopted for its simplicity and sensitivity. In Fig. I, the test coil is indicated by PlL1. It is connected to the bridge by about

Jan 1, 1946

By R. G. Patterson

The usual procedure in determining the magnetic susceptibilities of rocks and formations has been to take samples in the field and measure their volume susceptibilities in the laboratory, using one of numerous methods available. In none of these methods is the measuring instrument suited for field use. Usually the sample is pulverized; sometimes it is machined to a desired sue and shape, and in one method1 a cast of the sample is made and the susceptibility of the rock compared with that of a material of known susceptibility of the same size and shape, made from the cast of the original sample. Some writers assert that the difference in susceptibility of a rock sample in powdered and solid forms is negligible, and while doubtless this is true in many cases there are others in which the difference becomes appreciable. Further, the susceptibility of a small specimen may differ from that of the rock from which it is taken, owing to the stresses produced by the hammering or other forces used to obtain the sample and shape it for testing. Wilson2 found that an individual specimen of granite had about the same susceptibility in the solid as in the powdered form, but that pieces from different parts of the rock varied as much as 750 per cent because of unequal distribution of magnetite. The most accurate value of susceptibility would, obviously, be obtained from averag- ing a number of tests on the undisturbed rock instead of from one or two samples. No such procedures have been published, to the writer&apos;s knowledge. It is the purpose of this paper to describe a method by which susceptibilities of rocks may be determined in place by means of a portable instrument. Method The principle involved in this new method is that there is a change in inductance of a coil due to the presence in its magnetic field of a paramagnetic or dia-magnetic medium. In this case, however, the windings of the coil do not enclose any part of the rock under test. Instead, the coil is circular, being small in cross section as compared to its radius, and consists of several hundred turns of fine wire. It is placed flat on the rock of which the susceptibility is to be measured. Thus only part of the magnetic field from the coil penetrates the rock under test. The relation between the change in field strength or inductance of the coil and the susceptibility of the medium will be developed later. To measure the change in the inductance of the coil due to the presence of a magnetic material an alternating-current inductance bridge was chosen. Description of Apparatus Of many alternating-current bridge methods applicable,3 the one shown in Fig. 1 (Owen&apos;s bridge&apos;) was adopted for its simplicity and sensitivity. In Fig. I, the test coil is indicated by PlL1. It is connected to the bridge by about

Jan 1, 1946

By Irving B. Cadoff, Ernest Levine

The crack formation and propagation in the single -phase Cu-4 pct Ag alloys were studied. The alloys were loaded in mercury to various stress levels, the mercury was removed, and the specimen examined for cracks. Cracks were found to develop below the fracture stress; the frequency of such cracks increased with increasing stress level. Some cracks were nmpropagative. Fracture in mercury was found to occur by the link-up of cracks formed at various stress levels rather than by the growth and propagation of a single crack. If the mercury environment is removed prior to a critical amount of crack formation, then continued loading results in ductile fracture. The appearance of the cracks at selected grain boundaries is related to the relative orientation of the boundaries, as are the propaga-tive characteristics of the crack. The mercury interaction appears to be one of lowering the strength of the metal-metal bonds in the high-stress area of the grain boundary. GRIFFITH&apos;S microcrack theory1 proposed a critical crack size above which a crack in an elastic material grows with decreasing energy at a stress of From his theory it was proposed that the presence of a liquid tends to lower the surface energy of the microcrack faces2 leading to a decrease in the critical crack size necessary for spontaneous fracture propagation. stroh3 proposed that the stress concentration at a grain boundary due to pile-up may initiate a microcrack at the grain boundary. petch4 and Stroh5 evaluated the stress distribution at the head of a pile-up in a polycrystal-line material and deduced that the critical crack size and hence of is dependent on the grain size. Experimental verification of this dependence was found by petch6 for hydrogen embrittlement of steel. Studies in stress-corrosion cracking7 have provided a picture of fracture which shows that initial separations occur in a scattered, independent fashion in regions of high tensile stress. A minimum or threshold stress is necessary to produce a sufficient stress concentration to initiate frac- ture. These separations join up to form a crack. The extension of fracture is largely discontinuous and consists of a joining up of cracks. In recent worka evidence of this scattered crack network was found in a Cu-Ag alloy embrittled by mercury. For the Cu alloy-Hg couple, the crack path has also been found to be dependent on the orientation of adjacent grains, and with the addition of zinc to mercury a reduction in embrittlement along with a change in fracture morphology was found.9 In this present study, a mercury-dewetting method was used to observe crack initiation and fracture morphology when a Cu-4 pct Ag alloy is deformed in mercury and Hg-Zn solutions. PROCEDURE Specimens of Cu-4 pct Ag were prepared as in previous crack-path studies.&apos; The specimens were heated at 770°C for 24 hr and water-quenched Tension tests using a table-model Instron were carried out in mercury and in various concentrations of Hg-Zn. Loading was in steps up to the fracture stress, with the load being removed and the specimen examined for surface cracks at each step. The specimens were dewetted after each load to permit examination of the surface structure and rewetted prior to continued loading. The specimens were wetted by electro polish ing in phosphoric acid, rinsing in alcohol, and then immersing in a pool of mercury. Dewetting was accomplished by flame heating the specimen for 30 sec in a vacuum. Some surface contamination was found, but not enough to obscure crack configurations and grain boundaries. RESULTS Fracture Characteristics in Mercury. Fig. 1 is a stress-strain curve showing the progressive step-wise loading of the specimen. As may be seen from the graph, the first position stopped at a is at a stress 5000 psi below the expected fracture stress of 25,000 psi. Examination of the specimen after removal of mercury showed only one crack. The appearance of this crack at a stress far below the fracture stress of this alloy in mercury did not affect the stress-strain curve in any manner. The specimen was then recoated with mercury and deformation was continued (curve b, Fig. 1) raising the stress by 4000 psi, and the same procedure re~eated. The initial crack was located and appeared as in Fig. 2 (crack lb). In this figure the crack is

Jan 1, 1964

By Thomas Fraser, Alvaro Abreu

The work described in this paper was carried out under the sponsorship of the Foreign Economics Administration and in cooperation with the Departamento Nacional da Produggo Mineral, Rio de Janeiro. The project was undertaken to obtain complete data on the variations in washability of coal to be used for coke manufacture in the steel industry and to determine the economy of preliminary hand-sorting operations. The coal-producing industry of Brazil is in that pioneering stage in which operating practices and methods are just being developed. Increased wartime demand for fuel, coincident with a drastic curtailment of foreign supplies due to lack of shipping facilities, has put a tremendous pressure on the national industry to furnish more coal. Under this incentive, production facilities are being -expanded- and new methods of operation are being tested. Such changes are being developed both by improvement of existing methods that originated in the field and by adaptation and modification of methods introduced from the United States and Europe. These mining conditions and mining practices in Brazil are typical of what the American mining engineer will find in many instances when he goes pioneering into the developing coal fields of the Southern Hemisphere. The producing coal fields of Brazil are all in the southern states of that country. The coal measures are in a band roughly paralleling the coast and extending in a generally southwesterly direction from northern Sao Paulo through the states of Paraná, Santa Catarina and Rio Grande do Sul to near the Uruguayan border in the vicinity of Bajé. The accompanying map1 (Fig. I) shows the general location of these fields and also the principal routes of movement of both national and imported coal in a late pre-war year (1940). Statistical data on production by states up to that year are given in Table I. Rio Grande do Sul is still the largest producer among the coal states; but wartime

Jan 1, 1947