Search Documents

By E. L. Claridge, K. S. Lee

Areal sweep efficiency of oil displacement by enhanced-viscosity water exhibiting pseudoplastic behavior was measured in a Hele-Shaw model representing one-quarter of a five-spot pattern. The pseudoplasticity of polymer solutions and the velocity distribution in the five-spot pattern produced a condition under which the mobility ratio between the displacing and the displaced fluid could not be assigned a single value. Instead, the movement of the displacement front is governed by local mobility ratios which are also time dependent. The areal sweep at breakthrough with polymer solutions was poorer than the sweep obtained with Newtonian fluids of comparable viscosity. However, the areal sweep at 1 PV throughput was greatly improved as compared to flood water without polymer. It was also demonstrated that, even after the oil-cut had declined to a low value during a regular waterflood, switching to polymer flood efficiently swept out the oil remaining in the model. INTRODUCTION The behavior of fluid displacements in isotropic porous media for various patterns of injection and production wells has been extensively investigated.1-7 These investigations all concerned Newtonian fluids, i.e., the viscosity of each fluid was constant regardless of flow rate. The generally unfavorable influence on areal sweep efficiency of higher mobility of the displacing fluid as compared to the mobility of the displaced fluid has been established for both miscible and immiscible fluids. The principle was also established that a close correspondence exists between miscible and immiscible flood front behavior,2, 3 although oil recovery in a waterflood at unfavorable mobility ratio may be less than that observed in a miscible displacement at the same mobility ratio. This is true even when oil recovery is expressed on the basis of movable oil. The reason is that oil saturation only slowly achieves its final value behind the water-flood front in accordance with the Buckley-Leverett8 simultaneous flow relations. It is convenient to use miscible displacements for laboratory simulation of waterflood frontal advance since the interfacial tension forces which are negligible in proportion to viscous forces on a reservoir scale9 are thus made nonoperative in the laboratory model. For miscible displacements, the Hele-Shaw type of model adequately represents a porous medium so long as the appropriate scaling rules5-10 are observed in its design and operation. During simulation of waterflood front behavior in the laboratory by using miscible displacements, the behavior of connate water may ordinarily be disregarded since it is usually indistinguishable from flood water in this process. However, when the flood water is deliberately thickened to improve the mobility ratio between water and oil. the effect on the sweep efficiency due to generation of a connate water bank during the process must be considered. In a uniform porous medium, such a bank is generated11 and efficiently displaced by injection of thickened water.l2 The oil originally in-place at the start of the waterflood is then displaced by connate water followed by thickened water. If the flood water must be thickened to obtain a favorable mobility ratio, the mobility of the oil phase is appreciably less than that of the connate water. Hence, the oil phase is inefficiently displaced by the connate water bank, and a considerable proportion of the oil comes in contact with and is displaced by the thickened waterflood front' A recent study 12 of five-spot displacements using miscible Newtonian fluids in which connate water banks of various sizes were simulated shows that, for connate water banks as large as 40 percent of 1 PV, major improvements in sweep efficiency resulted from use of a thickened

Jan 1, 1969

By R. C. Ruder, C. E. Birchenall

The method of decrease in surface activity was used to determine the rates of diffusion of Co" into cobalt and into nickel. Since the absorption curves for cobalt radiation were quite complex under the conditions of these experiments, the effects of geometry and surface preparation on the diffusion results were investigated. The cobalt self-diffusion coefficients obey the equation DCoco = e-61100/RT cm2 per sec. For dilute cobalt diffusing in nickel, DConi, == 1.46 e-/R' cm2 er sec. AS part of the general program to measure the self-diffusion and dilute-solution diffusion rates of the iron-group metals, the diffusion coefficients of cobalt into cobalt and nickel have been measured using the radioactive isotope Co"'. Self-diffusion studies in iron have been previously reported by Birchenall and Mehl.' The technique of measurement used was the decrease in surface activity method described by Steigman, Shockley, and Nix.' It has been determined that scattering of the measured beta radiation by the specimen matrix is significantly influenced by the condition of the surface and the counting geometry. Accurate diffusion coefficients can be calculated from the activity data provided that the specimens have plane diffusion surfaces and that the absorption properties of the emitted radiation are determined under geometrical conditions duplicating with external absorbers the absorption and scattering in a thin film at the specimen surface as nearly as possible. The cobalt used in this research was originally in the form of hydrogen reduced rondels 99.9+ pct pure. The nickel had been prepared by the carbonyl process and was found by spectrographic analysis to contain 0.03 pct Fe, 0.04 pct Co and smaller traces of other metallic elements for a balance purity of 99.9+ pet Ni. Both materials were vacuum melted and cast in rectangular ingots. Specimens 7/8x7/8x1/4 in. were machined from these ingots. The specimens were then ground to 4-0 emery paper and annealed in hydrogen for at least a day at 1200°C. Some of the specimens were used in preliminary experimentation after which their diffusion faces were machined to remove the radioactive material from the previous diffusion experiments. After grinding, the specimens were polished using an electrolytic lapping technique described by Mazia." This lapping was continued until at least 0.005 in. was removed from the diffusion surface. The final surfaces were metallographically smooth except for a few fine scratches caused by the glass cloth. A large percentage of the area was undisturbed as determined by microscopic examination. The grain diameters of the diffusion specimens varied from 0.1 to 5 mm. There were no effects due to grain boundary diffusion in the experiments

Jan 1, 1952

By John S. Marshall

The purpose of this paper is to present to the profession data and experience obtained over a period of 5 years in the operation of 87 shaker-conveyor units, and the production of 2,169,638 tons of run-of-mine anthracite coal. The data are not generally available and should be of interest to those concerned with the operation of anthracite and bituminous mines. To simplify comparison, a ton of 2000 lb. of raw run-of-mine coal has been used as the production unit throughout this paper. Mining Methods and Equipment The mine is in the vicinity of Wilkes-Barre, Pa., in the Buried Valley area of the Susquehanna River. Seven veins were mined, varying in thickness from 18 in. to 8 ft. The cover overlying the veins varied from 200 to 800 ft. Three-fourths of the 1200 acres of property was covered with from 100 to 200 ft. of water-bearing gravels and clays, which prevented first mining under rock cover less than 50 ft. and pillar removal under rock cover less than 100 ft. The property was opened by two shafts sunk on the mountainside to avoid the sand and gravel present in the river valley. The veins dipped an average of 5" from the shafts. In certain areas the veins were practically flat and in some places a reverse pitch as high as 5" was encountered for short distances. A daily output of 3800 tons was hoisted on a two-shifi; hoisting operation. The mining consisted of 75 per cent pillar removal, and of the total production in the later years of operation 80 per cent was loaded by shaker conveyors, chain conveyors and scraper loaders. Shaker conveyors accounted for 70 per cent of the total output; chain conveyors and scraper loaders for 10 per cent. All conveyor work was double-shifted and 25 per cent was triple-shifted. A total of 87 shaker-conveyor units were on the property, of which 75 were kept in operation at all times.

Jan 1, 1940

By John S. Marshall

The purpose of this paper is to present to the profession data and experience obtained over a period of 5 years in the operation of 87 shaker-conveyor units, and the production of 2,169,638 tons of run-of-mine anthracite coal. The data are not generally available and should be of interest to those concerned with the operation of anthracite and bituminous mines. To simplify comparison, a ton of 2000 lb. of raw run-of-mine coal has been used as the production unit throughout this paper. Mining Methods and Equipment The mine is in the vicinity of Wilkes-Barre, Pa., in the Buried Valley area of the Susquehanna River. Seven veins were mined, varying in thickness from 18 in. to 8 ft. The cover overlying the veins varied from 200 to 800 ft. Three-fourths of the 1200 acres of property was covered with from 100 to 200 ft. of water-bearing gravels and clays, which prevented first mining under rock cover less than 50 ft. and pillar removal under rock cover less than 100 ft. The property was opened by two shafts sunk on the mountainside to avoid the sand and gravel present in the river valley. The veins dipped an average of 5" from the shafts. In certain areas the veins were practically flat and in some places a reverse pitch as high as 5" was encountered for short distances. A daily output of 3800 tons was hoisted on a two-shifi; hoisting operation. The mining consisted of 75 per cent pillar removal, and of the total production in the later years of operation 80 per cent was loaded by shaker conveyors, chain conveyors and scraper loaders. Shaker conveyors accounted for 70 per cent of the total output; chain conveyors and scraper loaders for 10 per cent. All conveyor work was double-shifted and 25 per cent was triple-shifted. A total of 87 shaker-conveyor units were on the property, of which 75 were kept in operation at all times.

Jan 1, 1940

By George Rice

THE subject of violent bumps in coal mines has been again brought to attention by a recent succession of such occurrences in the coal mines of the Cumberland field of eastern Kentucky and southern Virginia, which have caused fatalities and injuries to underground employees, a report on which is being issued by the United States Bureau of Mines1. The A.I.M.E. has had two valuable papers on bumps in the No. 2 Mine, Springhill, Nova Scotia, each followed by general discussion on bumps and their causes2. This paper gives a brief review of suggested causes and remedial measures given in English, Canadian and United States reports on bumps in coal mines, and then presents suggestions arising from the writer's recent investigation of the bumps in the Cumberland mines, made at the request of the mine operators, to determine the causes and remedies. These bumps, which occur under the simplest natural conditions, provide better opportunity for analysis of causes and effects than afforded under more complex conditions. The simple conditions in this field consist of relatively thin and level coal beds and uniform roof strata free' from folding and faulting.

Jan 1, 1935

By B. B. A. Luzzat

ALUMINUM is today the most widely used of the nonferrous metals. The technical literature on the aluminum smelting process is, nevertheless, very meager, so that anyone interested in the subject cannot rely on more than a couple of dozen publications.' The patent literature is equally scarce; most patents refer to the production of alumina from aluminum-bearing ores, while not more than a few score significant patents deal with the electrolytic reduction of alumina, which is the real core of the aluminum smelting industry. The "reduction phase" is, from a technical and a scientific point of view, much more interesting than the "alumina phase", which, in effect, is only a combination of such well-known chemical operations as dissolving, precipitating, filtering, drying, and calcining. The electrolytic reduction of alumina, on the other hand, has features which do not appear in any other metal smelting operation. Some of them are of great technical and scientific interest even for those not directly engaged in the production of aluminum. The purpose of this paper is to describe in some detail the basic facts and developments of the reduction phase of aluminum smelting. Two Aspects of the Electrolytic Process The raw material for the reduction process is alumina (Al2O3) . Its purity in general runs as high as 99.50 pct or more. Small differences in the chemical composition generally do not affect the reduction process.* Of more importance are the physical prop- erties of the alumina, since they affect not only its rate of solution in the molten bath but also its heat insulating power.† In the following pages, un- less otherwise stated, it is assumed that a standard "Bayer" alumina is used. The reduction process, by which alumina is broken down into its components, may be roughly defined as its electrolysis in molten cryolite. The oxygen separates at the anode, and the aluminum at the cathode, which forms the bottom of the electrolytic cell. The electrolytic cell (or pot) where the process is carried out is a strongly reinforced steel box. The

Jan 1, 1951

By A. H. Larson, R. J. McClincy

The activity of Sb,03 in PbO-Sb,03 slags containing less than 50 mol pct Sb,03 was determined by the inert-gas saturation method at 700°C. In this composition range, the activity gf SbzO3 shows a strong negative deviation from ideality. The activity of PbO in these slags was calculated by application of the Gibbs-Duhem iniegration to the Sb203 activity data. The calculated activity of PbO in slags containing more than 63 mol pct PbO was found to deviate in a positive direction from ideality uthile a negative deviation was found for slags containing less PbO. The standard Gibbs free energies of formation of Sb,03 and PbO. Sb203 have been calculated and compared with existing data in the literature. The activity of Sb203 in PbO-Si0,-Sb203 (PbO/SiO, = 2) slags containing less than 25 mol pct Sb,03 was also determined by the inert-gas saturation method at 700°C. In this composition range, the activity of Sbz03 shows a very large negative deviation from ideality. VERY little experimental work has been published in the past to determine equilibrium data in the oxide systems connected with the refining of lead. These data are of value since impurities such as antimony, arsenic, and tin must be removed from lead and recovered for further treatment. Equilibrium studies on antimony and arsenic systems are also of interest for the design of new processes for lead refining and lead dross treatment. Maier and ~incke' first determined the liquidus curves for the PbO-Sb203 system and identified the compound PbO . Sb203. They found the phase diagram for this system to be two simple eutectics located on either side of the congruent melting compound. They also determined a very limited amount of vapor pressure data for Sb406 abbve PbO-Sba3 melts at 697"~. A second phase diagram investigation on this system was reported by Hennig and Kohlmeyer' who confirmed the existence of the compound PbO . Sb203 as well as the form of the diagram. A disagreement was noticed, however, in that their liquidus temperatures over nearly the entire composition range were higher than those reported by Maier and Hincke. Barthel~ and pelze14 redetermined the liquidus curve at the PbO-rich end of the PbO-Sb@, system and agreed very closely with the results of Maier and Hincke. None of the investigators mentioned above reported any mutual solid solubility in the PbO-SbD3 system. Zunkel and Larson5 have determined the phase diagram for the PbO-rich end of the PbO-Sb203 system by slag-metal equilibrium studies in the Pb-PbO-Sb203 system and by thermal analysis studies in the PbO-Sbz03 system. A maximum solid solubility of 5.6 mol pct Sb203 in PbO was observed at the eutectic temperature of 604°C. Their results for the phase diagram agree favorably with those of Maier and Hincke. The vapor pressure of Sb2O3 in the temperature range from 470" to 800°C has been determined by Hincke, using a modification of the transportation meth~d.~ His results for temperatures below the melting point of Sba3 are the only data reported in the published literature. The predominant vapor species has been shown to be Sb,06 by Norman and staley.? Myzenkov and Klushin,8 using the boiling-point method, have determined the pressure of Sb406 above liquid SbD3 in the temperature range from 715" to 1025°C. The agreement between these two studies is not very close. A portion of the discrepancy lies in the fact that Hincke used silica crucibles, which were attacked by the liquid Sbz03 at high temperatures. This fact does not account, however. for the large difference observed at the melting point. ~aier' gives a brief summary of vapor pressure data for Sb,O, above pure liquid Sbz03 which agree quite well with the data of Myzenkov and Klushin at temperatures near the melting point. This paper describes the determination of Sb2O3 activity data in the PbO-Sb203 and Pb0-Si02-Sb203 (PbO/SiOz = 2) systems by the inert-gas saturation method. These activity data are compared with the data calculated by Zunkel and arson. EXPERIMENTAL Materials. The materials used in this investigation were analytical reagent-grade PbO (99.8 pct PbO, 0.14 pct insoluble in CHsCOOH, 0.02 pct not precipitated by HB, 0.1 pct CaO, and 0.08 pct SiOz), Sbf13 (99.6 pct Sb203, 0.004 PC~ C1-, 0.005 PC~ SO;-, 0.15 p~t AS, 0.001 pct Fe, and 0.03 pct other heavy metals such as Pb), and SiOz (chromatographic grade). Apparatus for Vapor Pressure Determinations. The apparatus used in this investigation consisted of a transportation reaction system with two separate gas trains. The argon transporting gas was first mixed with a small amount of hydrogen, metered, and dried by passage through silica gel and anhydrone drying tubes arranged in series. After this preliminary drying, the argon was passed through copper wool at 500°C to convert the residual oxygen to water vapor which was removed by three anhydrone drying tubes. A second stream of argon was metered and dried and then passed around the outside of the alumina reaction tube to flush away the volatile species to pre-

Jan 1, 1970

By A. J. Ardell

SASS and cohenl (S-C) have recently reported some transmission electron microscope observations of an interesting effect which they call "veining". They observed veining in thin foils of solution-treated and (in certain cases) aged samples of a Ni-10.3 at. pct Ti-0.6 at. pct A1 alloy (assumed equal to 10.9 at. pct Ti). S-C suggest that veining in solution-treated samples is due to the selective electrolytic etching of titanium-rich regions in alloys which are otherwise homogeneous. They associate the veins with the discrete titanium-rich regions detected in a magnetic study of aging in this system by Ben Israel and Fine,' and they also suggest that the initial strengthening of aged Ni-Ti alloys is due to these titanium-rich regions, rather than the formation of the coherent precipitate (Ni3Ti, L12 crystal structure).

Jan 1, 1970

By R. A. Breitrick, J. N. Swinderman, J. J. Cooper, H. L. Bauer Jr.

The Robinson Mining District, near Ely, Nev., is one of the major porphyry copper districts in the world. Within the district is an eight mile long east-trending zone of altered porphyry, metamorphosed sedimentary rocks, and sulphide mineralization surrounded by Paleozoic limestone, dolomite, shale and sandstone, Tertiary volcanics, and Quaternary alluvium. Six major disseminated ore deposits have been exploited in this zone. About 20% of the district production has come from disseminated ore in metamorphosed sedimentary rocks found adjacent to altered quartz-monzonite porphyry. The following brief statements summarize some of the relations between porphyry alteration, metamor-phism, and mineralization: 1) Disseminated copper ore does not occur in unaltered porphyry or in m-metamorphosed sedimentary rocks. 2) Sedimentary rocks have been only weakly metamorphosed where intruded by unaltered porphyry. 3) Intensely metamorphosed sedimentary rocks are found only adjacent to altered porphyry. 4) Many hydrothermal minerals are common to both altered porphyry and adjacent metamorphosed sediments. 5) Disseminated ore is found in altered porphyry and adjacent metamorphosed sedimentary rocks. 6) In general, there is a direct correlation between grade of ore in porphyry and copper content in the adjacent rocks. 7) Chemical changes in the altered porphyry and metamorphosed rocks appear to be related. The foregoing relations support a hypothesis that the porphyry alteration, the metamorphism of the sedimentary rocks, and the ore deposition were all part of a continuous hydrothermal process which probably closely attended the porphyry intrusion. The Robinson Mining District, most often referred to as the Ruth or Ely District, is located in eastern Nev. and is one of the major porphyry copper districts of the world. Production from 1908 through 1962 was nearly 250 million tons of ore averaging a little over one percent copper with a total metal value of nearly one billion dollars. The ore has been produced from six major disseminated-type deposits with the Liberty Pit deposit accounting for 70% of the total district production. Less than one million tons of base metal and gold ores have been produced from the replacement-type deposits of the district. Approximately 20% of the district production has come from underground mining operations; the pit ore has been mined with shovels and removed by train haulage, truck-train haulage combinations, truck haulage, and presently by a combination truck-skip system. Many of the ore deposits formerly worked by underground methods have been and are being exploited by open pit methods. (See Fig. I.) Two co.'s have accounted for virtually the entire production from the district. In 1958 Kennecott Copper Corp. acquired the district assets of Consolidated Coppermines Corp. and is now the sole ore producer in the district. Present operations are confined to the Liberty Pit where 22,500 tons of ore averaging a little less than 0.8% copper is mined per day. Cutoff grade is 0.4% copper, and the stripping ratio is three to one. The ore is hauled by rail 23 miles to the McGill Reduction Plant where it is concentrated to about 20% copper. Molybdenite is recovered as a by-product in the mill. The copper concentrates are smelted in McGill, and the blister copper is shipped for refining to Balt. where gold, silver, platinum and palladium are recovered. The Robinson Mining District has been well known as a porphyry copper district for the past fifty years, but many geologists are unaware of the fact that a large portion of the production has come from disseminated ore found in metamorphosed sedimentary rocks. The scope of this paper describes the occurrences of disseminated ore in the various metamorphosed sedimentary rocks, and presents evidence for the hypothesis that these ores are genetically, spacially, and coevally related to the disseminated ore in the porphyry rocks. Publication of this paper was granted by the management of Kennecott Copper Corp. A. H. James suggested and encouraged the writing of the manuscript. Special mineralogical and spectrographic analyses were performed by the Kennecott Research Center. The deposits of the district have been studied by many geologists since the turn of the century, and

Jan 1, 1964

By G. R. Belton, Y. K. Rao

A galvanic cell, using liquid MgCl2 or MgC12-CaC12 mixtures as the electrolyte, has been used to determine activities in Mg-A1 liquid alloys between 700' and 880°C. The incovporation of a chlorine electrode in the cell also allowed measurements to be made of the standard free energy of formation of MgCl2(l). The results are shown to be in good agreement with thermo-chetrlical values from the literature, and this is taken as evidence that the small, known solubility of magnesium in iMgCl2 introduces no significant error in galcanic cell measurements. Within experimental error, the activity coefficients and relative partial molar enthalpies at 800°C are shown to be represented by the following "subregular" solution equations: logy~~ =-0.68(1 -xMgj3 log yAL =-1.02(1 - XMf + 0.68(1 - XMf H.M = -4400(1 - %)3 / cal Mg 7Ag' HZ =-6600(1 - xA1)' + 4400(1 - XMf cal SCHNEIDER and toll' have used a transpiration technique to measure the vapor pressures of magnesium over Mg-A1 alloys between 544" and 594°C. amsstad,' however, has since suggested that the extrapolation to zero flow rate, used by these authors in interpreting their apparent pressure vs flow rate data, gives unreliable results. Rogers, Tomlinson, and Richardson,3 in interpreting the results of solution equilibria between Mg-A1 alloys and liquid MgC12, also considered the measurements of Schneider and Stoll to be unreliable and preferred to derive activities for the alloys from the earlier boiling point determinations of ~eit~ebel~ and the partial molar heats recommended by Kubaschewski and ~atterall.~ These latter heats were based substantially on the early calorimetric work of Kawa-kami but, unfortunately, his work on other systems has sometimes been found to be inaccurate.7 Rogers et al., in the above-mentioned paper,3 tentatively concluded that the most likely species responsible for the limited solubility (0.3 mole pct at 800°C) of magnesium in MgC12 were Mg° (neutral) and Mg2++. Two more recent studies8,9 have supported Mg2++ as the soluble species. In the present study, activities in Mg-A1 alloys have been determined by means of a galvanic cell involving liquid MgCl2 or MgC12CaCl, mixtures as the electrolyte. Since the reactive nature of magnesium precluded simple Faraday yield experiments, a chlorine electrode was incorporated in the cell in order that the performance of the cell could be checked by measurements of the heat and free energy of formation of MgC12. This procedure was considered necessary since it has been suggested1' that the solubility of a metal in a molten salt might introduce electronic conductivity; also, previous determinations of the standard electrode potential for MgC12 differed by as much as 70 mv11-13 EXPERIMENTAL Materials. Analyses of the materials used in preparing the alloys and the electrolyte mixtures are presented in Table I. The alloys were prepared by induction melting weighed amounts of the metals in a graphite crucible held under an argon atmosphere. Pure anhydrous magnesium chloride was prepared by heating the mixture MgCl, . 6H20 +NH4C1(1:1) to 650°C, followed by melting under dry argon. The melting point of the dry MgC12 was found by differential thermal analysis to be 714.8oC, which compares well with the accepted value of 714C.14 This agreement was taken to be an indication of the high purity of the dried salt. Table I. Compositions of Materials, wt pn Impurity Mg Al MgCI2 CaCI, Ba - - 0.005 Ca - - 0.010 Cu 0.02 0.02 Fe - 0.10 0.001 0.010 Pb 0.01 - 0.001 0.005 Mn 0.15 0.001 Si - 0.10 Sr - - 0.005 MBSO* - 0.040 ARGON TUNGSTEN CHLORINE LEAD—411 11 II ALUMINA 'A I / ave GRAPHITE on irA~_ ( ^"l ROD MAGNESIUM S>ILICA~^ /, OR ALLOY-. I /A] ___________ -«^- _ ELECTROLYTE I y FRITTED DISCS Fig. l—Arrangement of chlorine and metal electrodes in electrolytic cell.

Jan 1, 1970

By H. C. Fiedler

The development of cube-on-edge secondary re crystallization texture in Si-Fe strip depends upon the ability of inclusions, such as manganese sulfide, to restrain nomal grain gvowth. The ability of inclusions to perform this function is shown to depend upon their size and distribution. The desired uniform dispersion of many small inclusions is obtained by controlling the cooling rate from above the solution tempmature of the inclusions or, alternatively, by drastic 'quenching from above the solution temperature followed by heat treating at a lower temperature. The development of the cube-on-edge secondary recrystallization texture in Si-Fe strip depends upon both establishing the proper primary recrystallization texture and having inclusions to restrain normal grain growth. It has been suggested that the first requirement is met with a texture which, though weak, is near (110)[001]. A mechanism for secondary recrystallization originally proposed by ielsen' is consistent with the presence of this primary texture. It is visualized that a secondary grain appears where two adjacent grains happen to be sufficiently similar in orientation to be capable of behaving as a single large grain. This pair of grains will grow at the expense of its smaller neighbors as a consequence of its having lower grain boundary free energy. Other explanations of the origin of the secondary recrystallization texture have been offered,' and it can be concluded that the mechanism is not fully understood. Nevertheless, it is apparent that operationally the necessary primary recrystallization texture is obtained simply by interposing an anneal during the cold reduction to final gage. The role of inclusions in the development of the secondary recrystallization texture has been demonstrated by May and Turnbull4 in a comparison of a high-purity heat and a heat containing manganese sulfide. They showed that the driving force for secondary recrystallization is inversely proportional to the diameter of the matrix grains and that the function of the inclusions is to maintain a small matrix grain size. Other inclusions, such as various sul- fides,')' silicon nitride,8 and vanadium nitride,' titanium carbide,'' and vanadium carbide," have been shown to be effective in promoting secondary recrystallization to the cube-on-edge texture. There is also evidence that silica inclusions in Si-Fe strip made by powder-metallurgy techniques perform this function.' This report is concerned with the second of the two requirements for secondary recrystallization, namely the importance of the metallurgical control of the size and therefore number of inclusions. While the concepts involved are simple, they are fundamental to the making of this material. EXPERIMENTAL PROCEDURE A heat containing 3.27 pct Si, 0.026 pct S, 0.06 pct Mn, and 0.004 pct C was made in an air induction furnace from electrolytic iron, 98 pct ferro-silicon, electrolytic manganese, and iron sulfide. The heat was divided between graphite and baked-sand molds with a cavity 2-5/8 by 5 in. and with walls 2-3/4 in. thick. Slabs, 1 in. thick and 2-5/8 by 5 in., were cut from the ingots and hot-rolled either in the as-cast condition or after one of the heat treatments described later. After pickling, the 80- to 100-mil-thick hot-rolled band was, unless otherwise noted, heat-treated for 5 min at 900°C before being cold-rolled to 25 mils. After a heat treatment of 1 to 3 min at 860°C, the strip was cold-rolled to 12 mils, the final thickness. The percent cube-on-edge texture was determined by dividing the maximum torque as averaged from four samples by the maximum torque of a 3-1/4 pct Si-Fe single crystal having the (110) plane in the plane of the sample. The torque measurements were made in a field of 1000 oe on 1-in.-diam disks. RESULTS AND DISCUSSION The importance of the thermal history of the ingot is evident in Fig. 1 from the appearance of strips heat-treated in a temperature gradient. The sample

Jan 1, 1964

By F. H. Bunge, W. H. Jr. Dailey

This paper covers an investigation of the magnetic roasting characteristics of several iron ores when treated in the form of small pebbles (1/8" to 1/2" in size), and in the form of balled fines. The roasting treatment was carried out with apparatus capable of very close control of time, temperature, face velocity, and per cent combustible in the reaction gas. The effect of rapid initial heating was not studied although it is believed that this has a major effect on the results when processing solid pebbles. The test equipment is a fixed bed type, with such a wide range of gas velocities, temperature, combustible content and etc., that the results obtained can be made to approximate those from various commercial roasting processes. The data presented in this report covers reaction rates, effect of processing variables on silica in the concentrate, flow resistance of beds, and to a limited extent, the effect of particle size. The work is far from complete and raises many more problems than it gives answers for. We believe, however, that much of the information will be useful to those engaged in investigation of magnetic roasting processes. We measured the time required for various degrees of completion of the reaction of hematite to magnetite, for finely pound material in balled form and for carefully sized crushed ore. Measurements were made for a variety of Minnesota and Labrador ores. This report covers an ore requiring fine ginding (-325 M) for liberation (Lower Kevin) and an ore requiring coarser grinding (-100 M) for liberation (Upper Olson). These ores represent approximately the range of characteristics for a group in the west end of the Mesabi Range. Our data shows that the reaction rate is very fast for the finely ground material and that tests are readily reproducible. The reaction rate of the larger size material, in the range of 1/8" to 1/2", is much slower and the results more erratic. We found that for the ores tested, the percentage of silica in the Davis tube magnetic concentrate was a function of iron recovery. Normally the concentrate had a low and relatively uniform percentage of silica up to a critical value of recovery. Above this critical recovery value the percentage of silica increased very rapidly. For example, for one particular ore roasted in the form of 3/8" diameter balls made from -28 mesh fines, the silica remained at about 7% to 8% until the recovery exceeded about 93%. Increasing the recovery beyond 93% resulted in over 25% silica with the additional recovery. The degree of conversion of hematite to magnetite (% completion of roast) required to obtain 93% recovery for balled material, varied inversely with the gas flow rate. Percentage silica in the concentrate resulting from roasting 3/16" and 1/2" solid material was relatively erratic. However, for varying degrees of iron recovery the lowest silica percentages corresponded to those obtainable when roasting fines. It is thought the probable reason for the erratic values was the variation in shattering or cracking of the pebbles during initial heating and roasting. There is some indication that very fast initial heating will greatly increase the permeability of the individual particles of ore to gas flow so that the reaction rate for coarse sizes will approach that obtainable with balled fine material.

Jan 1, 1961

By John V. Morgan

Although the Lansing-Kansas City groups One one of the more important producing horizons of Central Kansas, exploitation has been hindered by inability to consistently identify and correlate the various productive intervals. A study of gamma ray-neutron logs and core data indicates that definite zones exist which are related to production and which may be generally correlated over an appreciable portion of Central Kansas. A suggested system of zoning and nomenclature is developed and illustrated, along with examples of its specific application in overall evaluation and in development of zonal production characteristics. General adoption of the suggested system should aid appreciably in the future development of commercial Lansing-Kansas City production in Central Kansas. It is probable that similar systems might be developed for other regions where production is obtained from various uncorrelated and unnamed zones in thick pay intervals. GENERALIZED GEOLOGY OF CENTRAL KANSAS The most important large subsurface feature in Central Kansas regarding oil production is the Barton Arch, which is part of the Central Kansas uplift. The Barton Arch is a buried ridge of Pre-Cambrian granite running northwest-southeast, near which the majority of Central Kansas oil fields have been found. To the northeast of this arch, the granite dips sharply into the Salina Basin and similar basin areas to the west and south are termed the Hugoton Embayment and Anadarko Basin, respectively. This report deals Primarily with the region of the Central Kansas Uplift and its southwestern flank. Fig. 1 indicates the general location of subsurface structural features along with the oil and gas fields of central Kansas. Above basal granite lies the Cambro-Ordovician Arbuckle Dolomite which is the principal oil producing zone in Central Kansas. This formation, as well as those higher in the section, reflects the general underlying granite structure; however, the Arbuckle top is an erosional surface and most oil producing structures are probably topographic hills. Formations above the Arbuckle in ascending order may include those of the Ordovician, Silurian, Devonian, Mississippian, Pennsylvanian, and Permian periods as well as certain recent sediments. As the Barton Arch is approached, those formations below the Pennsylvanian and above the Arbuckle tend to pinch out until Pennsylvanian rocks, which include the Lansing-Kansas City groups, rest directly upon the Arbuckle. The Arbuckle itself is also completely eroded away at points on the Arch, but is up to 600 ft thick only 20 to 30 miles down dip. Formations of the Pennsylvanian system vary considerably in thickness but probably average about 1,000 ft as an overall total. The more commonly known oil productive zones are the Tarkio, Topeka, Toronto (Dodge), Lansing-Kansas City and Marmaton. Of these, the Lansing-Kansas City, which varies from about 200 ft to 400 ft in thickness, is the most important, since its areal frequency of oil production is exceeded only by that of the Arbuckle. Most Pennsylvanian rocks in Central Kansas were deposited in shallow seas which alternately covered, then retreated from the land. This resulted in recurring cycles of thin beds which cover relatively large areas. Small surface deformations during the period of deposition also caused variations in the type material deposited and its thickness. The local structures of Pennsylvanian time probahlv influenced the accumulation of

Jan 1, 1952

By Charles R. Cavanaugh, John F. Elliott

The activity of nickel in liquid Pb-iVi alloys which are rich in lead was measured in the temperature region of 700° to 1100°C by means of the galvanic cell: The electrolyte used was stabilized zirconia. Tlze data were correlated using the a function, and a plot of the temperature coefficient aE/aT All subsequent calculations of the thermodynamic properties are based on these two functions. The activity, activity coefficient, and molar properties of mixing of nickel are reported. Nicke1 shows extreme positive deviations frorn ideality while lead shows a very slight positive deviation in the composition range studied The study of the activity of nickel in liquid Pb-Ni alloys reported herein was undertaken to explore the use of stabilized zirconia, an oxygen-ion electrolyte, with liquid-metal electrodes, and to obtain further information on the thermodynamic properties of the liquid binary Pb-Ni system. The cell The reversible electromotive force of the cell results from the difference in the chemical potential of the oxygen at the two electrodes: po, (left) - p~ (right) = -4E5 [I] The chemical potential of oxygen on the right is fixed by the activity of nickel in the solution and pure solid nickel oxide. That on the left is set by pure solid nickel in equilibrium with pure solid NiO. By definition: Since the chemical potential of nickel is related to the chemical potential of oxygen through the equilibrium constant for the formation of NiO from nickel and oxygen gas, the electromotive force of the cell is also expressed In this case, n is 2, E is the reversible potential of the cell, and 5 is Faraday's constant. The work of Kuikkola and wagnerl and Schmalz-reid2 has shown that the stabilized zirconia electrolyte is essentially an ionic conductor at the oxygen levels encountered in the experimental arrangement of the work, i .e., PG > 10-l7 atm. THE EXPERIMENTS The advantage of this type of reversible cell over those using a liquid electrolyte is the simplicity arising because the electrolyte also functions as one of the containing crucibles. A further simplification was the choice of the Ni (sat.)-NiO electrode as the standard. This permitted a ready check on the behavior of the electrolyte, as the potential of the cell must become zero when the right electrode becomes saturated with nickel, either because of a change of temperature or because of the addition of nickel to the electrode. It also permitted the potentials being measured to lie in the most satisfactory experimental range of 0 to 100 mv. Although it was not theoretically necessary, lead was included in the standard electrode as it assured good contact between the electrode and electrolyte. Cell Design. The general arrangement of the experimental cell assembly is shown in Fig. l(a) and the details of the cell itself are contained in Fig. l(b). The anode lead wire on the interior of the cell was connected to a coil of perforated sheet nickel. Within this coil were nickel oxide pellets which were held beneath the surface of the liquid Pb-Ni alloy. A disc of nickel oxide was held at the bottom of the external crucible (alumina) by means of the thermocouple protection tube. The nickel oxide disc and pellets were compressed dry at 10,000 psi and sintered at approximately 1000°C for an hour in air. A major experimental difficulty of reversible electromotive force cells with liquid electrodes is the selection of suitable materials for connecting

Jan 1, 1964

By E. H. Denny

In the past few years many men, including technically trained engineers, have been asphyxiated in metal mines, coal mines, tunnels and surface wells where a few relatively simple precautions with regard to ventilation and air testing would have saved them. Death from mine gases is analogous in some respects to death from poison and from drowning. The respiratory passages of a victim who has breathed oxides of nitrogen from burning explosives are badly irritated and a few hours or even a day after exposure he may develop a quick and fatal pneumonia; if, however, he enters without respiratory protective apparatus an atmosphere deficient in oxygen (a condition that may occur in unventilated or poorly ventilated parts of all underground mines) he collapses and if not rescued dies more quickly and surely than a lone nonswimmer who falls suddenly into deep water. An example of an atmosphere virtually without oxygen was demonstrated by an air sample taken by a Bureau of Mines engineer wearing oxygen breathing apparatus in a Cripple Creek shaft some years ago, during the recovery of the bodies of two victims of asphyxiation; analysis of the sample by the Pittsburgh laboratory of the Bureau showed the presence of 18.40 per cent of carbon dioxide, 0.27 per cent of oxygen, and 81.33 per cent of nitrogen, although the atmosphere apparently was clear and normal. In a mine one can pass from good, breathable air to an atmosphere that will kill as quickly as one can dive from a board to deep water below. Some Instances of Asphyxiation by Gases in Metal Mines The following typical examples of comparatively recent instances of asphyxiation in metal mines were taken chiefly from reports of various kinds of the U. S. Bureau of Mines.

Jan 1, 1940

By E. H. Denny

In the past few years many men, including technically trained engineers, have been asphyxiated in metal mines, coal mines, tunnels and surface wells where a few relatively simple precautions with regard to ventilation and air testing would have saved them. Death from mine gases is analogous in some respects to death from poison and from drowning. The respiratory passages of a victim who has breathed oxides of nitrogen from burning explosives are badly irritated and a few hours or even a day after exposure he may develop a quick and fatal pneumonia; if, however, he enters without respiratory protective apparatus an atmosphere deficient in oxygen (a condition that may occur in unventilated or poorly ventilated parts of all underground mines) he collapses and if not rescued dies more quickly and surely than a lone nonswimmer who falls suddenly into deep water. An example of an atmosphere virtually without oxygen was demonstrated by an air sample taken by a Bureau of Mines engineer wearing oxygen breathing apparatus in a Cripple Creek shaft some years ago, during the recovery of the bodies of two victims of asphyxiation; analysis of the sample by the Pittsburgh laboratory of the Bureau showed the presence of 18.40 per cent of carbon dioxide, 0.27 per cent of oxygen, and 81.33 per cent of nitrogen, although the atmosphere apparently was clear and normal. In a mine one can pass from good, breathable air to an atmosphere that will kill as quickly as one can dive from a board to deep water below. Some Instances of Asphyxiation by Gases in Metal Mines The following typical examples of comparatively recent instances of asphyxiation in metal mines were taken chiefly from reports of various kinds of the U. S. Bureau of Mines.

Jan 1, 1940

By B. H. Bergstrom, Will Mitchell, T. G. Kirkland, C. L. Sollenberger

IN a previous article' the authors outlined a study of the variables in rod milling and also reported data from a series of open circuit grinding tests on a massive limestone in a 30-in. x 4-ft end peripheral discharge rod mill. As a second part of the experimental program, an analysis is now presented for the 30-in. x 4-ft overflow rod mill grinding under identical conditions, except that discharge ports on the periphery of the mill shell have been sealed so that the products from the present series overflowed through a 9-in. diam .opening in the center of the end plate. A variance analysis has been made of the combined data for the two experiments, and performances of the two mills are compared here. Included in the first report' were descriptions of feed preparation, rod mill circuit, instrumentation and controls, and techniques used to evaluate data. Dependent and independent variables were defined, and variance analyses were made to test the relative significance of variables and to establish magnitude of error for the experiment. Significant data were plotted in various combinations, and conclusions were drawn from the graphs. The procedure and analysis in this series of tests follows the first tests and is not repeated. Data from the second series are recorded in Table I. Listed in the first three columns are the independent variables of feed rate (1000, 2000, 3000, 4000, and 5000 1b per hr), mill speed (50, 60, 70, 80, and 90 pct of critical), and pulp density (50, 60, 70, and 80 pct). The dependent variables, Pso, P100, reduction ratio, slope of the log-log sieve analysis curve, power demand, and Bond work index follow. Of these, only the reduction ratio and the Bond work index were analyzed for significance. Production of new surface as calculated from sieve analyses has not been included for this series because of the questionable assumptions that have to be made to satisfy the formulas involved. The large number of products obtained during the runs precluded the use of surface measurement techniques by the gas adsorption methods at this time; however, samples of all products have been stored for future reference. To test the consistency of the reporting of the sieved products, an averaged sieve analysis was calculated from the wet-dry plots obtained from the three product samples of each run. The resulting averaged analysis was plotted and the P80, selected. The relative deviations of the P80's from each of the three product samples with respect to the P80 of the averaged analysis were then calculated. In only two sets were the relative deviations (6.2 and 9.9 pct) considered excessive. In each of these two sets, one sieve analysis was obviously out of line; hence that analysis was ignored and new averages were computed. This reduced the relative deviations to 1.2 and 2.7 pct respectively. The relative deviations of the product analyses with respect to their averages ranged from 0.1 to 1.4 pct at 1000 lb per hr, 0.0 to 1.1 pct at 2000 lb per hr, 0.2 to 3.0 pct at 3000 lb per hr, 0.3 to 4.3 pct at 4000 lb per hr, and 0.5 to 5.2 pct at 5000 lb per hr. The relative deviation of the 80 pct passing point for 96 dry sieve analyses of the feed with respect to that of the averaged analysis was 7.6 pct. This slightly higher percentage can probably be attributed to a greater proportion of tramp oversize in a crusher product than is ordinarily found in a rod mill product. The last column on Table I lists the adjusted work index, which has been used as the measure of efficiency for the various combinations of operating conditions investigated. Efficiency increases as the index becomes lower. It was reported in the previous paper that the work indexes for the Waukesha limestone used in these experiments decreased as the product size decreased (as calculated from Bond grindabilities). That is, this limestone becomes easier to grind as the material becomes finer. This is unusual, because the work index for most materials as calculated from the Bond grindability has remained constant as the product size decreased or has increased slightly. Table II lists the results of Bond grindability tests at all mesh sizes from 3 to 200 and the work indexes calculated from them. To remove this variation of work index with product size from the data so that results would apply to any material of constant work index, the work index values shown in Table II were plotted against product size on log-log paper. From this curve (a straight line function in this case), the expected work index for the product size for each of the runs of the experiment was obtained. The work indexes as calculated from the reduction ratio and energy consumption were then divided by the corresponding expected work index. The results obtained are reported in percentages on Table I as adjusted work index and are actually percentages of the work index for the Waukesha limestone at the size in question. Multiplication of the work index value for a material of constant index by these percentages should allow the application of the adjusted work index curves to the material. Only the adjusted work index values, not the actual experimental values, were used for the variance analyses and for the graphs.

Jan 1, 1956

By F. F. Craig

The authors have done a commendable job in combining a number of recognized waterflood performance prediction methods into one composite method. The availability of a FORTRAN program for this composite method should encourage its widespread industry use. Pan American has had a computer program developed along similar lines for a number of years,' and it has received more use than any other reservoir prediction method. In three important stages of a pattern waterflood, the authors fail to consider fully the effects of water-oil mobility ratio on performance. This is discussed in the following paragraphs and modifications of the prediction method are suggested. During the early stages of a waterflood in a partially depleted formation, the injected water and its preceding oil bank move out radially from the injection wells. As pointed out in the author's paper the method of Yuster and Calhoun2 or predicting the water injection rate during this period assumes that the mobilities of the water and oil are equal. In his book, Muskat3 resents a modification of the Yuster-Calhoun approach that considers fully the influence of water-oil mobility ratio. In Muskat's method, the prediction of the injection rate-injected volume-time relationship is expressed in readily programmed dimension-less unts. At and following fillup the five-spot pattern consists of a water-invaded pattern with the remainder of the pattern containing only oil and connate water. In the paper, Eq. 18 is used to calculate the water injection rate at fillup. This equation considers that the entire pattern is invaded by water. To properly consider both the incomplete areal sweep of water and the water-oil mobility ratio, Eq. 18 should read:

Jan 1, 1969

By Nathaniel Herz

The formula very frequently used for computing the economical size of pipe to transmit compressed air is that of D'Arey, as follows: D = cV w1l Where, D = the volume of compressed air delivered in cubic feet per minute, at the final pressure. c = an experimental coefficient determined for the various sizes of pipe, d = the diameter of the pipe in inches. 1 = the length of the pipe in feet. p, = the initial gauge-pressure in pounds per square inch, p2 = the final gauge-preesure in pounds per square inch. w1 = the density of the air, or the weight in pounds per cubic foot at the initial pressure, p1. The most common case is that in which the given quantities are: the quantity of air required, the length of the pipe, and the initial pressure. The method of solution is to assume a pressure-loss and to compute the remaining factor, cd5, thus giving the size of pipe corresponding to the assumed loss of pressure. It is always desirable to try two or more pressure-drops, in order to find the combination that is most satisfactory, since often a small change in the size of pipe will reduce or increase the loss of pressure several pounds. An alternative method is to assume a size of pipe and calculate the corresponding pressure-drop. Each method involves a series of tedious calculations to arrive at the most economical solution, and also requires the use of tables giving the constant, c, the density of the air, w1, and often, for convenience, a table giving the values of the expressions p1-p2 and c J I hare constructed a graphic chart, Fig. 1, for the solution of

Jan 1, 1913

By Caner Zanbak

Deformational behavior of a rock mass can be modeled with a constitutive law based on theories of elasticity, and plastic and viscous deformation. For most rock types, such constitutive models may be used with confidence because there is no geochemical interaction between the rock-forming minerals and water. However, if volume changes in the rock due to geochemical phase transitions are predicted, then these volume changes must be converted into mechanical parameters and must be included into the constitutive laws. In this paper, geochemical phase transitions between anhydrite (CaS04) and gypsum (CaS04-2H20) will be brought to the attention of researchers in rock mechanics. Hydration of anhydrite to gypsum may yield volume increases up to 62.6 percent and dehydration of gypsum to anhydrite may cause volume decreases up to 38.5 percent. If one were to convert the volume increases in hydrating anhydrite into strains and calculates the required stresses to restrict the expansions, the magnitude of stresses will be found at GPa levels. Such stresses on swelling anhydrite layers cannot be provided by geologic media. Therefore, the host rocks will deform under these high stresses. On the other hand, under increasing stresses, geochemical transition of anhydrite to gypsum may stop after some hydration of anhydrite, and anhydrite and gypsum systems may become stable. Changes in temperature and solution compositions in the anhydritel gypsum system also control the stability of the geochemical system, and therefore, the extent of volume changes. A similar conceptual model can be drawn for volume decreases due to dehydration of gypsum to anhydrite. In this case, stress reduction on the gypsum layer may cause extensive fracturing and changes in the state of stress in the host rock mass.

Jan 1, 1984