Search Documents

By G. A. Colligan, G. L. F. Powell

A new experimental technique has been developed to study nucleation behavior in eutectic alloys. It is somewhat similar to that applied by Sundquist and Mondolfo1 but with the advantages that: 1) bulk samples are undercooled instead of small droplets thus allowing the thermal behavior to be monitored by a thermocouple immersed in the sample, and 2) nucleation behavior is investigated in the same sample on either side of the eutectic composition by adding additional component to the sample under controlled conditions which preclude the addition of nu-cleation contaminants. Sundquist and Mondolfo carried out ]nucleation ex-periments on a large number of eutectic alloy sys-tems and concluded that nonreciprocal nucleation operated. If one phase a was a good nucleant for the other phase 0, then B was a poor nucleant for a. This was determined experinlentally by comparing the nucleation temperatures of 100 to 300 u diameter droplets of hypereutectic and hypoeutectic composition cooled from above the liquidus and from a temperature between the liquidus and the eutectic temperature. Primary phase a was concluded to be an efficient nucleant for the other phase B, if the following experimental result was obtained. Referring to Fig. 1, the temperature TI at which a drop of hypereutectic alloy of composition B froze when cooled from above the B liquidus was noted. This was the nucleation temperature for B in the absence of a. A drop of hypoeutectic alloy of composition A was then frozen from temperature T2 between the a liquidus and the eutectic temperature. The temperature T3 at which the eutectic nucleated in the presence of the primary or proeutec-tic a was noted. If this temperature T3 was higher than the temperature TI at which the B nucleated in a hypereutectic alloy, it was concluded that the primary a had nucleated the 6. This temperature T3, representing a certain undercooling below the equilibrium eutectic temperature Te , was designated ?TB by a> the undercooling below T, for nucleation of 13 by a. If there was no substantial difference in nucleation temperature between the hypereutectic drop cooled from above the /3 liquidus and the hypo-eutectic drop cooled from a temperature between the a liquidus and the eutectic temperature, it was considered that the a nucleated B at an undercooling equal to or greater than that at which P nucleated from a hypereutectic alloy. Sundquist and Mondolfo1 found that faceted primary crystals were good nucle-ants for metals that grow as orthogonal dendrites when present as the primary phase. Jackson2 has questioned Sundquist and Mondolfo's technique and proposed that in Sundquist and Mon-dolfo's samples, such as composition A, primary a retained B in reentrant grooves at their surfaces when heated to a temperature above the eutectic but below the a liquidus. This objection was suggested by experiments with organic eutectics where reten-

Jan 1, 1970

By M. D. Hassialis, A. F. Taggart

ark' observed some years ago that collector-coating reactions with xanthates and with fatty acids clearly follow paths parallel to those prescribed by the familiar mass-action law for reactions in dilute solutions. He proposed, therefore, the logical hypothesis that they are governed by the solubility-product principle. However, he went astray in the application of his proposal to collector coating by overlooking the fact that coating involves a heterogeneous reaction. A mistaken concept of the meaning of the word adsorption also entered. Wark thought that the concentration of metallic ion that must be used in setting up the solubility-product equation for the coating reaction was that which could be obtained by solution of the mineral. Since this is very low for sulphide ores, and since the amount of the collector ion necessary for coating produces an extremely low concentration, the resulting ion-concentration product, under conditions when coating occurs, is much lower than that which would indicate a saturated solution of the collector-coating compound. Hence he was forced to the position that the solubility product governing the coating is much smaller than the standard solubility product. To justify this position it was necessary to postulate a coating mechanism that did not obey the ordinary laws of chemical reaction. This Wark did by adopting the concept that adsorption is a property of matter, rather than merely a more or less ephemeral local concentration thereof. Thus he says (p. 142 of ref. I): "Adsorption is not a purely physical property of the solid surface, for the specific nature of the adsorbed molecule or ion is important." The result was that he destroyed the great potential utility of his postulate by tying it to this erroneous concept in the words (pp. 142, 143): "It will be obvious that the adsorption solubility product is less than the normal solubility product." The writers have found quantitatively in the case of galena and potassium ethyl xanthate, and semiquantitatively in the case of covellite and the same collector, that the coating reaction does follow the mass-action law to the extent that coating occurs when the ordinary solubility product of the coating compound is exceeded, and that coating does not take place under the reverse conditions. In the course of the investigation leading to the establishment of this fact it was necessary to work with xanthate concentrations so low (down to 0.0004 mg. per liter), that very long conditioning times, and bubble-contact times of as much as 16 hr. were necessary sometimes to follow the reactions. The results have led to some illuminating conclusions as to necessary collector concentrations in normal flotation operations, and the action of the frothing agent in connection therewith' The experimental work comprised accurate determination of the standard solubility product of lead ethyl xanthate, development of a much less laborious

Jan 1, 1947

By P. R. Sperry

Aluminum alloy 3S was examined to determine the relationship between the applicable phase diagram and the microstructures produced under conditions tending toward non-equilibrium as well as equilibrium. The only phases present in the alloy were aluminum, (Mn,Fe)A16, aAI(Mn,Fe)Si, and silicon. It was found that the alloy behaved essentially as though it belonged to the Al-Mn-Si system. The effects of various solidification rates and of various homogenization treatments were studied. Particular attention was given to a nonuniform precipitate distribution which reflected the solute distribution in the cast aluminum solid solution. Some possible explanations for the solute distribution based on characteristics of the Al-Mn-Si or AI-Mn systems were discussed. ALUMINUM alloy 3s (aluminum plus 1.25 pct Mn) is one of the oldest and the most widely used of the wrought aluminum alloys. In spite of this fact, there are some aspects of the metallography of 3s which have not been revealed or which have not been brought to the attention of the metallurgist working with the alloy. The purpose of this investigation was to demonstrate in general how some of the fundamentals of equilibrium phase diagrams may be applied to the study of an alloy and to show specifically the origin of certain metal-lographic features of aluminum alloy 3s. It is hoped that this information can serve as a basis for solving specific problems relating microstructure to such things as mechanical properties, recrystallization, grain growth, and surface finish. Literature Survey Considering that alloy 3s contains only one alloying addition, manganese, it seems reasonable that it would have characteristics pertaining to the A1-Mn system. However, those characteristics might well be altered by the impurities in the commercial alloy, especially iron and silicon. Therefore, not only the simple binary but also more complex systems had to be reviewed. One characteristic of the A1-Mn system worthy of mention is its sluggishness, which leads to conflicting solubility data1,'2 and makes it relatively easy to supersaturate the solid solution and shift the eutectic composition during rapid solidification.3'4 Another characteristic is the strong influence which small amounts of impurities, especially iron, exert in lowering the solid solubility of manganese. Undissolved manganese is ordinarily present in an intermetallic phase, MnAl,, having an orthorhombic crystal structure. A metastable precipitating phase designated as "G" has been reported but small amounts of iron and silicon suppress this phase entirely." Raynor has established that MnA1, can dissolve a considerable amount of iron by a substitution of iron for manganese atoms up to 50 atomic pct.'" Consequently, in the Al-Mn-Fe liquidus diagram, the eutectic valley separating the primary aluminum and (Mn,Fe)Al, fields is fairly close to a constant Mn + Fe content." This is an important consideration in regulating the composition of 3s and also other aluminum alloys with high manganese additions."

Jan 1, 1956

By E. W. Hough, G. L. Stegemeier

Empirical equations for surface tension of propane and normal butane as functions of reduced temperature are obtained from experimental data. Another correlation relating surface tension to enthalpy of vaporization is given for these two compounds. In addition, new paracbor numbers are calculated for the normal paraffin hydrocarbons. These numbers are utilized for the calculation of interfacial tension of two-component systems as functions of pressure and temperature, using a modified form of Weinaug-Katz equation. The experimental data for two binary systems are approximated by the correlation. From these results it is found that the interfacial tension in the high-pressure region remains extremely low at large pressure decrements below the critical pressure. Thus, it appears that condensate systems may have flow characteristics almost like single-phase conditions even though the pressure is within the two-phase region. Experimental data have shown that interfacial tension divided by density difference approaches zero as the critical pressure is approached. A calculation of wetting-phase saturations indicates that the saturation gradient at the two-phase contact becomes increasingly abrupt as the critical pressure is approached. DISCUSSION Prediction of the surface and interfacial tension of the light hydrocarbons and of two-component hydrocarbon mixtures at various temperatures and pressures may be made if other physical properties are known. Extensive experimental work on single-component and binary systemsl is the basis for the correlations outlined in this paper. Interfacial tension is defined as the specific surface-free energy between two phases of unlike fractional composition, while surface tension is defined as the specific surface-free energy between two phase:; of the same fractional composition. The usual definitions relating interfacial tension to a liquid-liquid interface and surface tension to a gas-liquid interface are not clearly defined when the critical region is included, and there is no sharp distinction between a gas and a liquid phase. Interfacial tension is probably the most important single force that makes one-half to one-third of the total oil actually in place in a reservoir rock unrecoverable by conventional gas-drive or waterflood methods. A rough estimate of this figure for the United States is 100 billion bbl. Interfacial tension presently is used by petroleum engineers in the estimation of saturation gradients at the gas-oil contact and at the oil-water contact. The data in this paper should prove useful for estimates of reserves involving gas-oil contacts. Relative permeability undoubtedly is influenced by interfacial tension, for sufficiently small values. These data should be useful in determining how small the values are In addition, these data should eventually add to our fundamental knowledge of surfaces. At the critical point, all surface excesses approach zero and the thickness becomes very large. SINGLE-COMPONENT SYSTEMS It has been observed1 that the following relationships are good approximations to the physical properties of propane and n-butane.

By Edwin M. Chance

During the last decade many conditions have been encountered that have materially increased the cost of the production of coal. As in most cases it has not been practicable to increase the selling price of such coal sufficiently to insure the necessary margin of profit, the mine management has been forced to avail itself of what might be termed unusual means that costs might be held at as low a figure as possible. The so-called efficiency engineer has been called upon, costly power plants have been built and machinery has been installed to replace manual labor wherever possible. Another aid used recently to secure economies through the more intelligent production of coal, is the chemist. As the coal industry, barring the production of byproduct coke, does not at once give evidence of its need of the services of the chemist, the writer will endeavor to point out a few of the services that this branch of the staff has been able to render. The preparation of coal in the past has been carried on entirely upon an empirical basis, that is, the criterion adopted has been an ocular inspection. Unfortunately, the appearance of a coal and especially of an anthracite, has but little relation to its fuel value, and as long as coal is purchased for the heat that can be obtained from it by its combustion, the quantity of such heat that is purchased must be one of the principal desiderata in selecting or preparing a coal. Were coals purchased for use as bric-a-brac or for exhibition in museums it might be both wise and just to purchase them upon their appearance. After 4 or 5 years of investigation the fact has been established that coals of very inferior appearance, and I now have special reference to anthracite, might and often did possess heating and burning properties superior to those possessed by bright coals which in the past had commanded considerable and uniform premiums in the market. This being the case the question arose as to whether the trade could be convinced of this fact. While at first some difficulty was experienced in establishing the quality of such dull coals, still it was found that the real obstacle to the sale of these materials in the past had been the fact that the coal producers' own sales departments felt convinced of the inferiority of this type of fuel and when complaints were registered they were given ready credence. Upon convincing the sales department of the quality of this type of fuel, but

Jan 1, 1917

By Akira Yazawa, Alžbeta Gubcova

RECENT lead-smelting techniques have tended toward use of high-grade concentrates with minimum amounts of flu, accompanied by profitable employment of roast reaction.1-5 In order to better understand these smelting processes, thermodynamical calculations have been carried out on the Pb-S-0 system, and the results obtained have been presented in isothermal reaction diagrams in which log Ps, and logPo, were the axes. The diagram thus constructed seems to be more convenient to grasp the equilibrium aspect than those published hitherto.6-8

Jan 1, 1968

By Walter M. Stephen

Modern developments in alloy steels have been so rapid and diverse that engineering practice has scarcely had time to re-appraise all items of past experience wherein conclusions became axiomatic under conditions that no longer apply. A case in point is the wet screening of abrasive ores within the fine range still looked upon as belonging exclusively to classifiers. By virtue of the development of stainless steels (18 per cent Cr, 8 per cent Ni), it is no longer true that classifiers are more economical than screens in closed circuit with large-tonnage ball or rod mills at 65 or even 100 mesh, provided a selective overgrind of the higher-gravity constituents of the ore is not desired. Wet screening of ores is a highly corrosive as well as an abrasive operation, because of the inevitably high degree of oxygenation of the water. Screen cloth of ordinary or spring-steel wire almost at once becomes pitted and covered with a film of corrosion products, which causes rust-blinding of fine-mesh screens and offers high frictional impedance to the flow of ore particles. On the other hand, the well-known properties of stainless steel enable it to maintain a bright surface, and so to eliminate blinding either by ore particles or by corrosion products. That a large-tonnage mill grinding hard ore to 65 mesh can be operated economically in closed circuit with screens instead of classifiers has recently been demonstrated at the Copper Cliff concentrator of the International Nickel Co.; in the test to be described, a 6½ by 12½-ft. Marcy rod mill ground from 625 to 820 tons of ore per day to approximately 65 mesh, operating in closed circuit with three 4 by 5-ft. Hum-mer screens, without any classifier. Stainless-steel cloth gave an indicated life of several months. There was no difficulty with blinding, yet dilution and spray water could be controlled so that screen undersize averaged not less than 40 per cent solids. In contrast, ordinary carbon steel was pitted and blind with rust within 40 hours.

Jan 1, 1939

By Walter M. Stephen

Modern developments in alloy steels have been so rapid and diverse that engineering practice has scarcely had time to re-appraise all items of past experience wherein conclusions became axiomatic under conditions that no longer apply. A case in point is the wet screening of abrasive ores within the fine range still looked upon as belonging exclusively to classifiers. By virtue of the development of stainless steels (18 per cent Cr, 8 per cent Ni), it is no longer true that classifiers are more economical than screens in closed circuit with large-tonnage ball or rod mills at 65 or even 100 mesh, provided a selective overgrind of the higher-gravity constituents of the ore is not desired. Wet screening of ores is a highly corrosive as well as an abrasive operation, because of the inevitably high degree of oxygenation of the water. Screen cloth of ordinary or spring-steel wire almost at once becomes pitted and covered with a film of corrosion products, which causes rust-blinding of fine-mesh screens and offers high frictional impedance to the flow of ore particles. On the other hand, the well-known properties of stainless steel enable it to maintain a bright surface, and so to eliminate blinding either by ore particles or by corrosion products. That a large-tonnage mill grinding hard ore to 65 mesh can be operated economically in closed circuit with screens instead of classifiers has recently been demonstrated at the Copper Cliff concentrator of the International Nickel Co.; in the test to be described, a 6½ by 12½-ft. Marcy rod mill ground from 625 to 820 tons of ore per day to approximately 65 mesh, operating in closed circuit with three 4 by 5-ft. Hum-mer screens, without any classifier. Stainless-steel cloth gave an indicated life of several months. There was no difficulty with blinding, yet dilution and spray water could be controlled so that screen undersize averaged not less than 40 per cent solids. In contrast, ordinary carbon steel was pitted and blind with rust within 40 hours.

Jan 1, 1939

By S. C. Das. Gupta, B. S. Lement

isothermal formation of martensite occurs in the range of —65o to —197oC and is always preceded by some athermal transformation. By rapid cooling the isothermal, but not the athermal, component of transformation can be suppressed. Stabilization against isothermal transformation can be induced by cycling from below M. to room temperature. A LTHOUGH the transformation of austenite to XV martensite is generally believed to occur only on cooling, recent evidence indicates that this reaction can also occur at constant temperature. Isothermal formation of martensite was observed in tool steel by Fletcher, Averbach, and Cohen.'. They found that the hardening reaction that occurs during the quenching of a plain carbon or low carbon alloy tool steel does not stop immediately when room temperature is reached; instead austenite continues S. C. DAS GUPTA is Research Fellow, Department of Metallurgy, University of Notre Dame, Notre Dame, Ind. B. S. LEMENT, Associate Member AIME, is on the Research Staff, Department of Metallurgy, Massachusetts Institute of Technology, Cambridge, Mass. Discussion on this paper, TP 3123E, may be sent, 2 copies, to AIME by Dec. 1, 1951. Manuscript, April 16, 1951. Detroit Meeting, October 1951. This paper represents part of a thesis by S. C. Das Gupta submitted in partial fulfillment of requirements for the degree of Doctor of Philosophy in Metallurgy to the University of Notre Dame. to transform at room temperature although at a decreasing rate. Since only a small amount of austenite transforms in this fashion, isothermal formation of martensite was considered to be merely a "tailing off" effect of the main hardening reaction. Another point of view was advanced by Kurd-jumov and Maksimova"' * who reported that the austenite-martensite reaction could be suppressed by rapid cooling of a 6 pct Mn-0.6 pct C steel in liquid nitrogen and that as much as 25 pct martensite could be formed by reheating to and holding at subzero temperatures above that of liquid nitrogen. These investigators came to the conclusion that martensite is thermally nucleated at certain special regions in the austenite and subsequently grows to observable dimensions. Isothermal transformation of austenite to martensite was cited by Fisher, Hollomon, and Turnbull" as evidence supporting another nucleation and growth theory of martensite formation. According

Jan 1, 1952

By W. J. Reagan

Many factors enter into the manufacture of basic open-hearth steel of high quality. Perhaps the two most important are temperature and the iron oxide content of the metal. If we can control these two factors we can essentially control basic open-hearth practice. SOURCE AND EFFECT OF IRON OXIDE Earlier investigators, especially Herty and his associates, have shown that iron oxide is introduced into the open-hearth furnace in four ways:' 1. By oxidation of the scrap by furnace gases. 2. By decomposition of the limestone. 3. By oxidation of the iron oxide in the slag by furnace gases. 4. By direct addition of iron ore to the charge. We also know that the speed of operation of an open-hearth furnace depends, for a given charge and given combustion conditions, on the rate at which iron oxide will diffuse from the slag into the metal. The rate of diffusion depends upon a number of variables, such as iron oxide content of the slag, slag viscosity, etc., which also depend upon the amount of iron oxide in the metal, amount of carbon present, temperature, and so forth. For a given carbon and a given temperature, the iron oxide content of the metal is in proportion to the iron oxide content of the slag. This fact can be easily verified by analysis of slag samples taken as described by Herty.2 It is preferable to take these samples just before deoxidetion. In killing the steel samples with aluminum it is desirable to use aluminum rod of 99 per cent purity; ordinary commercial aluminum rod with a purity of approximately 92 per cent is not satisfactory. In drilling these samples it is also essential to take the largest amount of drillings possible. This gives more accurate results because it eliminates spotty segregation of A12O3.

Jan 1, 1932

By G. R. Speich, R. A. Oriani

The rate of coarsening (Ostwald ripening) of copper precipitate Particles in an a-iron matrix has been studied in three Fe-Cu alloys containing 2.3, 4.0, and 5.4 wt pct Cu in the temperature range 730° to 830°C. The kinetics of Ostwald ripening ohevs the law as deduced by Lifshitz and Wagner so that matrix diffusion controls the process. The equilibrium shape of the particles is that of rods with hemispherical caps, and is due to the BOTH Lifshitz and slyozov and wagner3 have recently solved the complex problem of determining the rate of coarsening of an assembly of precipitate particles. Both workers, although using somewhat different mathematical approaches, arrive at the same equation for the relation between the mean radius 7 of a distribution of spherical particles and the bulk solubility co, diffusivity D in the matrix, large anisotropy in the copper/a iron interfacial free energy (y,/y, = 4). A Lifshitz -Wagner equation, modified for both the nonsphericity of the diffusion field and the reformulation of the Gibbs-Thomson equation for the case of nonsphencal particles, is derived. Using the modified equation, the calculated values of the mean radius are smaller than those observed by a factor of about one -half. absolute temperature T, gas constant R, surface free energy y of the precipitate/matrix interface, and the time t of aging: where V, is the molar volume of the precipitate and v is a stoichiometric factor. Wagner's treatment is restricted to the case of spherical particles growing in a liquid matrix where strain energy is not a factor. Lifshitz and slyozov have discussed the effect of anisotropic particle shapes and internal strains on the rate of coarsening. Oriani4

Jan 1, 1965

By Zay Jeffries

It has been known for centuries that iron and steel could be hardened by cold hammering and that the metal could be restored to the normal condition by heating to a red heat arid cooling, either rapidly or slowly with nearly pure iron, but slowly with steels containing considerable carbon. The art of tempering steels is also very old. When a medium- or high-carbon steel is quenched from a cherry-red heat, the hardness is increased; this hardness can be reduced by heating to various temperatures below the lower thermal critical point,, which is near 700" C. The present paper will not consider these old and well known changes in iron and steel below the thermal critical range but will confine itself to the more unusual changes, some of which have been studied recently. Stromeyer,1 for example, In 1886, reports that both working steel and heat treatment of steel in the blue-heat range arc highly injurious. Recently, however, some metallurgists believe that the straiglltening of warped steel forgings at a blue heat produces a beneficial effect on the metal2 The Engineering Division of the National Research Council has constituted a committee on Physical Changes in Iron and Steel below the Thermal Critical Range, which has the following personnel: K. R. -Abbott, H. C. Boynton, William Campbell, J. V. Emmons, F. B. Foley, H. J. French, H. M. Howe, Zay Jeffries (chairman), F. C. Langenberg, J. A. Mathews, P. D. Merica, A. H. Miller, J. H. Nelson, G. A. Reinhardt, W. E. Ruder, H. F. Wood. This committee is studying several aspects of the physical changes in iron and steel. The results, reported in the literature and obtained by recent experimentation, will be given; this will be followed by a general theoretical discussion of the more important

Jan 1, 1922

By Zay Jeffries

It has been known for centuries that iron and steel could be hardened by cold hammering and that the metal could be restored to the normal condition by heating to a red heat arid cooling, either rapidly or slowly with nearly pure iron, but slowly with steels containing considerable carbon. The art of tempering steels is also very old. When a medium- or high-carbon steel is quenched from a cherry-red heat, the hardness is increased; this hardness can be reduced by heating to various temperatures below the lower thermal critical point,, which is near 700" C. The present paper will not consider these old and well known changes in iron and steel below the thermal critical range but will confine itself to the more unusual changes, some of which have been studied recently. Stromeyer,1 for example, In 1886, reports that both working steel and heat treatment of steel in the blue-heat range arc highly injurious. Recently, however, some metallurgists believe that the straiglltening of warped steel forgings at a blue heat produces a beneficial effect on the metal2 The Engineering Division of the National Research Council has constituted a committee on Physical Changes in Iron and Steel below the Thermal Critical Range, which has the following personnel: K. R. -Abbott, H. C. Boynton, William Campbell, J. V. Emmons, F. B. Foley, H. J. French, H. M. Howe, Zay Jeffries (chairman), F. C. Langenberg, J. A. Mathews, P. D. Merica, A. H. Miller, J. H. Nelson, G. A. Reinhardt, W. E. Ruder, H. F. Wood. This committee is studying several aspects of the physical changes in iron and steel. The results, reported in the literature and obtained by recent experimentation, will be given; this will be followed by a general theoretical discussion of the more important

Jan 1, 1922

By W. Hume-Rothery

IN recent interesting papers,1,2 Bardos et al. have described ternary Laves phases of the type A2(BsSi) and A4(B5Si3) where A = titanium vanadium, niobium, and so forth, and B = manganese, iron, cobalt, or nickel; other more complex formulae have also been established. In these phases, silicon plays the part of the smaller B atom of a Laves phase AB2, and the interatomic distances show that the effec- tive silicon radii lie between 1.16 and 1.21Å, and are thus very much smaller than the metallic radius of silicon for CN = 12. It does not seem to have been pointed out that these small atomic radii are almost the sape as the normal covalent radius of silicon (1.174Å). If, therefore, silicon acts as an acceptor of electrons as suggested by Bardos et al.,1 it appears to do so, not by the building up of a negatively charged silicon ion which would be large, but by the formation of what are very nearly or may be actually normal covalent bonds. Since a covalent bond contains two electrons, its formation would reduce the number of electrons available for bonding in other parts of the structure, and in this way the effect of silicon in stabilizing the o phase at high electron concentrations might be understood.

Jan 1, 1965

By Read Winterburn

This study of the relationship of the accumulation and drainage of oil to the structural conditions in the Wilmington oil field is presented with the hope that the data contained herein will aid in efficient exploita-tion of other fields where similar conditions exist. It is also probable that the conditions observed in this field will enable accurate comparisons of various well-spacing programs as to efficiency of production and ultimate recovery. Formations in Wilmington Field Age Formation Thickness Lithology and Remarks Quaternary and Pleistocene. San Pedro 1000 t Fresh-water sands, gravels and clays Pliocene Upper Pico 800 t Alternating sands and silt- Stones Pliocene Middle Pico 0-200 ± Sands and siltstones Unconformity Pliocene Repetto 875-1150 Gray and green shales, silt-stones and sands at top grading to interbedded gray-ish brown shales and fine-grained sands toward bot-tom Miocene Puente 4100± Hard brown shales and sands. Sands are fine and uncon-solidated at top, becoming firmer and coarser grained toward bottom. Top por-tion contains layers of lam-inated diatomaceous shale Unconformity Schist The data included herein are not complete as to all areas and zones, being confined mostly to the area south of Anaheim Street. The sections presented are illustrative of edge-water conditions in the Terminal zone and Tar zone, but have not been extended down the structure far enough

Jan 1, 1940

By H. Scott

Since Bohler discovered, in 1903, on cooling certain alloy steels, the phenomenon of a new and lower temperature transformation than the usual Ar 3-2-1 obtained by increasing the maximum temperature to which the material was heated, much has been published1 connecting this phenomenon with a large number of dissimilar steels of high alloy content. From the fact that the transformation divides itself, taking place at two widely separated temperatures, it has been called a "split transformation." The significant facts established by recent investigators2 are: that when the transformation occurs at the higher temperature Ar1, troostite or a decomposition product is formed, and that when the transformation occurs at the lower temperature Ar", the resulting structure is martensite. The terminology Ar' and Ar" adopted here is that of Portevin. Previous Investigations Reviewing the work on this subject published in a recent issue of Revue de Metallurgie and referring in particular to his statement that martensite is a solution of carbide in alpha iron, Le Chatelier says :4 "How then can a theory already 20 years old demand new investigations? The reason for it is that we have not succeeded in proving directly the real presence of the transformation of iron during the very short duration of the quenching. The fall of temperature takes place at the rate of several hundred degrees per second and the observation of

Jan 1, 1920

By P. R. Sperry

In an investigation of the decomposition of the solid solution in a cold worked high-purity aluminum alloy containing 7 pct Mg, aged at temperatures from 30o to 82°C, the nucleating sites at the earliest stages of precipitation were observed to be of two types. Nucleation occurred at the high angle grain boundaries both when the alloy was initially cold worked and when solution annealed. Nucleation also occurred at certain unique deformation markings which began to appear in abundance at approximately 30 pct reduction in thickness by cold rolling. These deformation markings were identified as deformation (kink) bands rather than as the usually assumed "slip planes." Zn material that was cold rolled 15 pct, only the grain boundary Fig. 2—A1-7 pct Mg alloy, cold worked 60 pct and heated at 230° C for 5 min. Etched with Perryman's reagent. X500. Reduced approximately 25 pct for reproduction. (a) Bright field illumination, precipitate deeply pitted. (b) Phase contrast, showing slip markings.

Jan 1, 1962

By Staff

Concentrates at the rate of 1000 tons a day are being smelted by International Nickel Co.'s new commercial flash smelting furnace. Developed by Inco, the process is a radical departure from the former practice which involved conventional smelting in coal-fired reverberatory furnaces. In the new process copper flotation concentrate and flux are injected horizontally with oxygen into a specially designed reverberatory furnace, and smelting temperature is maintained solely by the flash combustion of iron and sulphur while the particles are in suspension. The major benefits of this new process stem from two sources: 1)-Substitution of energy from local resources for imported coal; and 2)-Production of liquid sulphur dioxide, replacing equivalent imported sulphur. A measure of these benefits is afforded by considering the saving, in 1954, of 60,000 tons of coal and the production of 70,000 tons of liquid sulphur dioxide, equivalent to 35,000 tons of sulphur.

Jun 1, 1955

By Jack Parker, Gonzalo Barrientos

The most realistic mine pillar design is based on observations and measurements in situ. Low-cost reliable instrumentation has made this approach possible. At the White Pine mine, with its thousands of pillars of all shapes and sizes under all kinds of loading conditions, practical pillar design criteria have been developed. The pressure arch theory is explained and work in two test panels o f the mine is described. The pressure arch mechanism, which relies on lateral stress for support, can be applied to puzzling roof and pillar conditions in other mines.

Jan 1, 1975

By J. W. Rutter, K. T. Aust

The motion of individual grain boundaries under a constant driving force was investi,qated for zone-refined lead, with and without solute tin additions. The rate of boundary migration was found to depend strongly on tin content and on the orientation relationship between the adjacent grains. The results are compared with the theory of impurity-controlled grain boundary miqration developed by Lucke and Detert. Evidence was found that grain boundaries separating grains which have the Kronberg-U&apos;ilson orientation relationships of 38 and 22 deg about <Ill> and 28 deg about <100>, correspond to boundaries of high mobility. The results are discussed in relation to the formation of annealing textures in metals and the structure of high-angle boundaries. It is generally known that small amounts of impurities in solid solution greatly influence the re-crystallization behavior of metals. For example, the addition of 0.005 at. pct of tellurium to copper,&apos; or 0.005 at. pct of silver to lead,2or 0.01 at. pct of manganese or nickel to aluminum3 greatly decreases the rate of recrystallization of these metals. However, this effect may be the combined result of a decrease in the rates of both nucleation and growth; recrystallization experiments do not separate these two factors. Bolling and winegard4 determined the effects of small quantities of tin, silver, and gold on grain growth in polycrystalline zone-refined lead.

Jan 1, 1960